Samsung AM180JNHFKH/EU User Manual

Features of your new air conditioner
Cool Summer Offer
On those hot sweltering summer days and long restless
nights, there is no better escape from the heat than the
cool comforts of home. Your new air conditioner brings an
end to exhausting hot summer days and lets you rest.
This summer, beat the heat with your own air conditioner.
Contents
Safety precautions .......................................................................... 3
Checking before use ................................................................... 10
Viewing the parts ......................................................................... 12
Cleaning and maintaining the air conditioner ............... 13
Appendix ......................................................................................... 14
Installation parts ........................................................................... 18
Cost Efficient System
Your new air conditioner not only provides maximum
cooling power in the summer, but can also be an efficient
heating method in the winter with the advanced “Heat
pump” system. This technology is up to 300% more
efficient than electrical heating, so you can further reduce
its running cost. Now, meet year-round needs with one air
conditioner.
Flexible installation
Duct type air conditioner is designed to be slimmer and
offers different solutions for any shape room allowing for
specific air flow requirements. Also, the air intake can be
set up on either the bottom or rear of the unit, so there is
more flexibility in installation.
This product has been determined to be in compliance with the Low Voltage Directive (2006/95/EC), the Electromagnetic
Compatibility Directive (2004/108/EC) and the Machinery Directive (2006/42/EC) of the European Union
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB
cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where
and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for disposal.
2
Safety precautions
ENGLISH
Before using your new air conditioner, please read this manual thoroughly to ensure that
you know how to safely and efficiently operate the extensive features and functions of your
new appliance.
Because the following operating instructions cover various models, the characteristics of
your air conditioner may differ slightly from those described in this manual. If you have any
questions, call your nearest contact center or find help and information online at www.
samsung.com.
Important safety symbols and precautions:
WARNING
Hazards or unsafe practices that may result in severe personal injury
or death.
CAUTION
Hazards or unsafe practices that may result in minor personal injury
or property damage.
Follow directions.
Do NOT attempt.
Make sure the machine is grounded to prevent electric shock.
Unplug the power plug from the wall socket.
Do NOT disassemble.
FOR INSTALLATION
WARNING
Use the power line with the power specifications of the product or higher and use
the power line for this appliance only. In addition, do not use an extension line.
 Extending the power line may result in electric shock or fire.
 Do not use an electric transformer. It may result in electric shock or fire.
 If the voltage/frequency/rated current condition is different, it may cause fire.
The installation of this appliance must be performed by a qualified technician or
service company.
 Failing to do so may result in electric shock, fire, explosion, problems with the
product, or injury.
Install a switch and circuit breaker dedicated to the air conditioner.
 Failing to do so may result in electric shock or fire.
Fix the outdoor unit firmly so that the electric part of the outdoor unit is not exposed.
 Failing to do so may result in electric shock or fire.
3
Safety precautions
FOR INSTALLATION
WARNING
Do not install this appliance near a heater, inflammable material. Do not install
this appliance in a humid, oily or dusty location, in a location exposed to direct
sunlight and water (rain drops). Do not install this appliance in a location where
gas may leak.
 This may result in electric shock or fire.
Never install the outdoor unit in a location such as on a high external wall where it
could fall.
 If the outdoor unit falls, it may result in injury, death or property damage.
This appliance must be properly grounded. Do not ground the appliance to a gas
pipe, plastic water pipe, or telephone line.
 Failure to do so may result in electric shock, fire, an explosion, or other problems with
the product.
 Never plug the power cord into a socket that is not grounded correctly and make
sure that it is in accordance with local and national codes.
FOR INSTALLATION
CAUTION
Install your appliance on a level and hard floor that can support its weight.
 Failing to do so may result in abnormal vibrations, noise, or problems with the
product.
Install the draining hose properly so that water is drained correctly.
 Failing to do so may result in water overflowing and property damage.
When installing the outdoor unit, make sure to connect the draining hose so that
draining is performed correctly.
 The water generated during the heating operation by the outdoor unit may overflow
and result in property damage.
In particular, in winter, if a block of ice falls, it may result in injury, death or property
damage.
4
FOR POWER SUPPLY
WARNING
Do not pull or excessively bend the power line. Do not twist or tie the power line.
Do not hook the power line over a metal object, place a heavy object on the power
line, insert the power line between objects, or push the power line into the space
behind the appliance.
 This may result in electric shock or fire.
FOR POWER SUPPLY
CAUTION
When not using the air conditioner for a long period of time or during a thunder/
lightning storm, cut the power at the circuit breaker.
 Failing to do so may result in electric shock or fire.
FOR USING
WARNING
If the appliance is flooded, please contact your nearest service center.
 Failing to do so may result in electric shock or fire.
If the appliance generates a strange noise, a burning smell or smoke, unplug the
power plug immediately and contact your nearest service center.
 Failing to do so may result in electric shock or fire.
In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate immediately
without touching the power line.
Do not touch the appliance or power line.
 Do not use a ventilating fan.
 A spark may result in an explosion or fire.
To reinstall the air conditioner, please contact your nearest service center.
 Failing to do so may result in problems with the product, water leakage, electric
shock, or fire.
 A delivery service for the product is not provided. If you reinstall the product in
another location, additional construction expenses and an installation fee will be
charged.
 Especially, when you wish to install the product in an unusual location such as in
an industrial area or near the seaside where it is exposed to the salt in the air, please
contact your nearest service center.
5
ENGLISH
When the circuit breaker is damaged, contact your nearest service center.
Safety precautions
FOR USING
WARNING
Do not touch the circuit breaker with wet hands.
 This may result in electric shock.
Do not strike or pull the air conditioner with excessive force.
 This may result in fire, injury, or problems with the product.
Do not place an object near the outdoor unit that allows children to climb onto
the machine.
 This may result in children seriously injuring themselves.
Do not turn the air conditioner off with the circuit breaker while it is operating.
 Turning the air conditioner off and then on again with the circuit breaker may cause a
spark and result in electric shock or fire.
After unpacking the air conditioner, keep all packaging materials well out of the
reach of children, as packaging materials can be dangerous to children.
 If a child places a bag over its head, it may result in suffocation.
Do not insert your fingers or foreign substances into the outlet when the air
conditioner is operating or the front panel is closing.
 Take special care that children do not injure themselves by inserting their fingers into
the product.
Do not touch the front panel with your hands or fingers during the heating
operation.
 This may result in electric shock or burns.
Do not insert your fingers or foreign substances into the air inlet/outlet of the air
conditioner.
 Take special care that children do not injure themselves by inserting their fingers into
the product.
Do not use this air conditioner for long periods of time in badly ventilated
locations or near infirm people.
 Since this may be dangerous due to a lack of oxygen, open a window at least once an
hour.
6
FOR USING
WARNING
Do not attempt to repair, disassemble, or modify the appliance yourself.
 Do not use any fuse (such as cooper, steel wire, etc.)other than the standard fuse.
 Failing to do so may result in electric shock, fire, problems with the product, or injury.
FOR USING
CAUTION
Do not place objects or devices under the indoor unit.
 Water dripping from the indoor unit may result in fire or property damage.
Check that the installation frame of the outdoor unit is not broken at least once a
year.
 Failing to do so may result in injury, death or property damage.
Max current is measured according to IEC standard for safety and current is
measured according to ISO standard for energy efficiency.
Do not stand on top of the appliance or place objects (such as laundry, lighted
candles, lighted cigarettes, dishes, chemicals, metal objects, etc.) on the appliance.
 This may result in electric shock, fire, problems with the product, or injury.
Do not operate the appliance with wet hands.
 This may result in electric shock.
Do not spray volatile material such as insecticide onto the surface of the appliance.
 As well as being harmful to humans, it may also result in electric shock, fire or
problems with the product.
Do not drink the water from the air conditioner.
 The water may be harmful to humans.
Do not apply a strong impact to the remote controller and do not disassemble the
remote controller.
Do not touch the pipes connected with the product.
 This may result in burns or injury.
7
ENGLISH
If any foreign substance such as water has entered the appliance, cut the power by
unplugging the power plug and turning the circuit breaker off and then contact
your nearest service center.
 Failing to do so may result in electric shock or fire.
Safety precautions
FOR USING
CAUTION
Do not use this air conditioner to preserve precision equipment, food, animals,
plants or cosmetics, or for any other unusual purposes.
 This may result in property damage.
Avoid directly exposing humans, animals or plants from the air flow from the air
conditioner for long periods of time.
 This may result in harm to humans, animals or plants.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
For use in Europe :
 This appliance can be used by children aged from 8 years and above and persons
with reduced physical,sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play
with the appliance. Cleaning and user maintenance shall not be made by children
without supervision.
FOR CLEANING
WARNING
Do not clean the appliance by spraying water directly onto it. Do not use benzene,
thinner or alcohol to clean the appliance.
 This may result in discoloration, deformation, damage, electric shock or fire.
Before cleaning or performing maintenance, unplug the air conditioner from the
wall socket and wait until the fan stops.
 Failing to do so may result in electric shock or fire.
8
FOR CLEANING
CAUTION
ENGLISH
Take care when cleaning the surface of the heat exchanger of the outdoor unit
since it has sharp edges.
 To avoid cutting your fingers, wear thick cotton gloves when cleaning it.
Do not clean the inside of the air conditioner by yourself.
 For cleaning inside the appliance, contact your nearest service center.
 When cleaning the internal filter, refer to the descriptions in the ‘Cleaning and
maintaining the air conditioner’ section.
 Failure to do may result in damage, electric shock or fire.
9
Checking before use
Operation ranges
The table below indicates the temperature and humidity ranges the air conditioner can
be operated within.
Refer to the table for efficient use.
MODE
OUTDOOR TEMPERATURE
INDOOR TEMPERATURE
COOLING
-15°C/5°F to 50°C/122°F
18°C/64°F to 32°C/90°F
HEATING
-20°C/-4°F to 24°C/75°F
27°C/81°F to less
DRYING
-15°C/5°F to 50°C/122°F
18°C/64°F to 32°C/90°F
INDOOR HUMIDITY
80% or less
• T he standardized temperature for heating is 7˚C/45˚F. If the outdoor temperature drops to 0˚C/32˚F or below, the
heating capacity can be reduced depending on the temperature condition.
If the cooling operation is used at over 32˚C/90˚F (indoor temperature), it does not cool at its full capacity.
NOTE
CAUTION
• The use of the air conditioner at a relative humidity above the expected one (80%) may
cause the formation of condensate and the leakage of water drops on the floor.
Maintaining your air conditioner
Internal protections via the unit control system
 This internal protection operates if an internal fault occurs in the air conditioner.
Type
NOTE
10
Description
Against cold air
The internal fan will be off to against cold air when the heat pump is heating.
De-ice cycle
(Defrost cycle)
The internal fan will be off to against cold air when the heat pump is heating.
Anti-protection of
internal battery
The compressor will be off to protect internal battery when the air conditioner operates
in Cool mode.
Protect compressor
The air conditioner does not start operating immediately to protect the compressor of
the outdoor unit after it has been started.
• If the heat pump is operating in Heat mode, De-ice cycle is actuated to remove frost from an outdoor unit that may
have deposited at low temperatures.
The internal fan is switched off automatically and restarted only after the de-ice cycle is completed.
Tips on using air conditioner
Here are some tips that you would follow when using your air conditioner.
RECOMMENDATION
Cooling
•If current outside temperatures are much higher than the selected
indoor temperature, it may take time to bring the inner temperature
to the desired coolness.
•Avoid drastically turning down the temperature. Energy is wasted and
the room does not cool faster.
Heating
•Since the air conditioner heats the room by taking heat energy
from outdoor air, the heating capacity may decrease when outdoor
temperatures are extremely low. If you feel the air conditioner
insufficiently heats, using an additional heating appliance in
combination with the air conditioner is recommended.
Frost & De-ice
•When the air conditioner runs in Heat mode, due to temperature
difference between the unit and the outside air, frost will form.
If this happens:
-The air conditioner stops heating.
-The air conditioner will operate automatically in De-ice mode for 10 minutes.
-The steam produced on the outdoor unit in De-ice mode is safe.
No intervention is required; after about 10 minutes, the air conditioner
operates again normally.
❈ The unit will not operate when it starts to de-ice.
Fan
•Fan may not operate for about 3~5 minutes at the beginning to
prevent any cold blasts while the air conditioner is warming up.
High indoor/
outdoor
temperatures
•If both indoor and outdoor temperatures are high and the air
conditioner is running in Heat mode, the outdoor unit’s fan and
compressor may stop at times. This is normal; wait until the air
conditioner turns on again.
Power failure
•If a power failure occurs during the operation of the air conditioner,
the operating immediately stops and unit will be off. When power
returns, the air conditioner will run automatically.
Protection
mechanism
•If the air conditioner has just been turned on after operation stops or
being plugged in, cool/warm air does not come out for 3 minutes to
protect the compressor of the outdoor unit.
11
ENGLISH
TOPIC
Viewing the parts
Congratulations on the purchase of the air conditioner. We hope you enjoy the features of your air conditioner and stay cool or
warm with optimal efficiency.
Please read the user manual to get started and to make the best use of the air conditioner.
BIG DUCT TYPE
Air filter (the return air side)
Ceiling
Air intake
Air outlet
NOTE
12
• Y our air conditioner and display may look slightly different from the illustration shown above depending on your
model.
Cleaning and maintaining the air conditioner
If the air conditioner will not be used for an extended period of time, dry the air conditioner to maintain it in best condition.
Periodical checks
Refer to the following chart to maintain the air conditioner properly.
Type
Indoor unit
Description
Monthly
Every 4
months
Once a year
Clean the condensate drain pan (2)
●
Thoroughly clean the heat exchanger (2)
●
Clean the condensate drain pipe (2)
●
Replace the remote control batteries (1)
Clean the heat exchanger on the outside of the unit (2)
Outdoor unit
●
●
Clean the heat exchanger on the inside of the unit (2)
●
Clean the electric components with jets of air (2)
●
Verify that all the electric components are firmly tightened (2)
●
Clean the fan (2)
●
Verify that all the fan assembly is firmly tightened (2)
●
Clean the condensate drain pan (2)
●
●: This check mark requires checking the indoor/outdoor unit periodically, following to the description to maintain the air
conditioner properly.
NOTE
CAUTION
• The described operations should be performed more frequently if the area of installation is very dusty.
• These operations must always be performed by qualified personnel. For more
detailed information, see the installation part in the manual.
13
ENGLISH
 Dry the air conditioner thoroughly by operating in Fan mode for 3 to 4 hours and
disconnect the power plug.
There may be internal damage if moisture is left in components.
 Before using the air conditioner again, dry the inner components of the air conditioner
again by running in Fan mode for 3 to 4 hours. This helps remove odors which may have
generated from dampness.
Appendix
Troubleshooting
Refer to the following chart if the air conditioner operates abnormally. This may
save time and unnecessary expenses.
PROBLEM
SOLUTION
The air conditioner
does not operate
immediately after it
has been restarted.
• B ecause of the protective mechanism, the appliance does not start
operating immediately to keep the unit from overloading.
The air conditioner will start in 3 minutes.
The air conditioner
does not work at all.
• C heck that the power plug is properly connected. Insert the power
plug into the wall socket correctly.
• Check if the circuit breaker is switched off.
• Check if there is a power failure.
• Check your fuse. Make sure it is not blown out.
The temperature
does not change.
• C heck if you selected Fan mode.
Press the Mode button on the remote control to select another
mode.
The cool (warm)
air does not come
out of the air
conditioner.
• C heck if the set temperature is higher (lower) than the current
temperature. Press the Temperature button on the remote control
to change the set temperature. Press the Temperature button to
decrease or increase the temperature.
• Check if the air filter is blocked by dirt. Clean the air filter every two
weeks.
• Check if the air conditioner has just been turned on. If so, wait 3
minutes. Cool air does not come out to protect the compressor of
the outdoor unit.
• Check if the air conditioner is operating in defrost mode. When the
ice formed in winter or the outdoor temperature is too low, the
air conditioner operates in defrost mode automatically. In defrost
mode, indoor fan stops and warm air does not come out.
• Check if the air conditioner is installed in a place with a direct
exposure to sunlight. Hang curtains on windows to boost cooling
efficiency.
• Check if the cover or any obstacle is not near the outdoor unit.
• Check if the refrigerant pipe is too long.
• Check if the air conditioner is only available in Cool mode.
• Check if the remote control is only available for cooling model.
14
SOLUTION
The fan speed does
not change.
• C heck if you selected Auto or Dry mode.
The air conditioner automatically adjusts the fan speed to Auto in
Auto/Dry mode.
Timer function does
not set.
• C heck if you press the Power button on the remote control after
you have set the time.
Odors permeate in
the room during
operation.
• C heck if the appliance is running in a smoky area or if there is a smell
entering from outside. Operate the air conditioner in Fan mode or
open the windows to air out the room.
The air conditioner
makes a bubbling
sound.
• A
bubbling sound may be heard when the refrigerant is circulating
through the compressor. Let the air conditioner operate in a
selected mode.
• When you press the Power button on the remote control, noise may
be heard from the drain pump inside the air conditioner.
Water is dripping
from the air flow
blades.
• C heck if the air conditioner has been cooling for an extended period
of time with the air flow blades pointed downwards. Condensation
may generate due to the difference in temperature.
Remote control is
not working.
•
•
•
•
The air conditioner
does not turn on or
off with the wired
remote control.
• Check if you set the wired remote control for group control.
The wired remote
control does not
operate.
• C heck if TEST indicator is displayed on the wired remote control.
If so, turn off the unit and switch off the circuit breaker. Call your
nearest contact center.
The indicators of
the digital display
flashes.
• P ress the Power button on the remote control to turn the unit off
and switch the circuit breaker off. Then, switch it on again.
ENGLISH
PROBLEM
Check if your batteries are depleted.
Make sure batteries are correctly installed.
Make sure nothing is blocking your remote control sensor.
Check that there are strong lighting apparatus near the air
conditioner. Strong light which comes from fluorescent bulbs or
neon signs may interrupt the electric waves.
15
Appendix
Model specification (Dimension and weight)
Dimension and weight
Type
Indoor unit
16
Model
Net dimension (WxDxH)
(mm)
Net weight
(kg)
AM180JNHFKH
1350*910*450
82.5
AM224JNHFKH
1350*910*450
82.5
ENGLISH
17
INSTALLATION PARTS
Indoor unit installation
When deciding on the location of the air conditioner with the owner, the following restrictions must be taken into account.
1
Place the pattern sheet on the ceiling at the spot where you want
to install the indoor unit.
• Since the diagram is made of paper, it may shrink or
stretch slightly due to temperature or humidity. For this
reason, before drilling the holes maintain the correct
dimensions between the markings.
• Pattern sheet is supplied depending on the model type.
2
Insert bolt anchors. Use existing ceiling supports or construct a suitable support as shown in figure.
3
Install the suspension bolts depending on the ceiling type.
Concrete
Insert
Hole in anchor
hole in plug
Suspension bolt(M10)-field supply
•Ensure that the ceiling is strong enough to support the weight
of the indoor unit. Before hanging the unit, test the strength of
each attached suspension bolt.
•If the length of suspension bolt is more than 1.5m,
it is required to prevent vibration.
• If this is not possible, create an opening on the false ceiling in
order to be able to use it to perform the required operations on
the indoor unit.
4
Ceiling support
Screw eight nuts to the suspension bolts making space for hanging
the indoor unit.
•You must install all the suspension rods.
5
Hang the indoor unit to the suspension bolts between two nuts.
•Piping must be laid and connected inside the ceiling when
suspending the unit. If the ceiling is already constructed, lay the
piping into position for connection to the unit before
placing the unit inside the ceiling.
6
Screw the nuts to suspend the unit.
7
Adjust level of the unit by using measurement plate for all 4 sides.
•For proper drainage of condensate, give a 3mm slant to the
left or right side of the unit which will be connected with the
drain hose, as shown in the figure. Make a tilt when you wish to
install the drain pump, too.
•When installing the indoor unit, make sure it is not tilted toward
front or back side.
18
When the drain hose is installed to the right.
3mm
Drain hose port
Performing leak test & insulation
Leak test
ENGLISH
◆ LEAK TEST WITH NITROGEN (before opening valves)
In order to detect basic refrigerant leaks, before recreating the vacuum and recirculating the R410A, it’s responsable
of installer to pressurize the whole system with nitrogen (using a cylinder with pressure reducer)
at a pressure above 40 bar (gauge).
◆ LEAK TEST WITH R410A (after opening valves)
Before opening valves, discharge all the nitrogen into the system and create vacuum. After opening valves check
leaks using a leak detector for refrigerant R410A.
Liquid refrigerant
G_1 port
Gas refrigerant port
• Discharge all the nitrogen to create a vacuum and charge the system.
 The designs and shape are subject to
change according to the model.
Insulation
Once you have checked that there are no leaks in the system, you can insulate the piping and hose.
1 To avoid condensation problems, place T13.0 or thicker Acrylonitrile Butadien Rubber separately around each refrigerant
pipe.
No gap
• Always make the seam of pipes face upwards.
•
The insulation has to be produced in full compliance of European regulation reg. EEC / EU 2037/ 2000 that requires the use of sheaths insulation form without using CFC and HCFC gases for health and the environment.
2 Wind insulating tape around the pipes and drain hose avoiding to compress
the insulation too much.
3 Finish wrapping insulating tape around the rest of the pipes leading to the outdoor
unit.
4 The pipes and electrical cables connecting the indoor unit with the outdoor
unit must be fixed to the wall with suitable ducts.
• A
ll refrigerant connection must be accessible, in order to permit
either unit maintenance or removing it completely.
NBR(T13.0 or thicker)
Insulation cover pipe
Insulation pipe
Indoor unit
Be sure to overlap
the insulation
5 Select the insulation of the refrigerant pipe.
• Must fit tightly against
◆ Insulate the gas side and liquid side pipe referring to the thickness body without any gap.
according to the pipe size.
◆ Indoor temperature of 30°C and humidity of 85% is the stan dard condition.
If installing in a high humidity condition, use one grade thicker insulator by referring to the table below.
If installing in an unfavorable conditions, use thicker one.
◆ Insulator’s heat-resistance temperature should be more than 120°C.
19
Performing leak test & insulation
Pipe
Pipe size
Liquid
pipe
Ø6.35 ~ Ø9.52
Ø12.7 ~ Ø19.05
Ø6.35
Ø9.52
Ø12.70
Ø15.88
Ø19.05
Gas
pipe
Insulation Type (Heating/Cooling)
Standard [30°C, 85%]
High humidity [30°C, over 85%]
EPDM, NBR
9t
9t
13t
13t
13t
19t
19t
Remarks
Internal temperature is
higher than 120°C
25t
◆ When installing insulation in places and conditions below, use the same insulation that is used for high humidity conditions.
<Geological condition>
- High humidity places such as shoreline, hot spring, near lake or river, and ridge (when the part of the building is covered by
earth and sand.)
<Operation purpose condition>
- Restaurant ceiling, sauna, swimming pool etc.
<Building construction condition>
- The ceiling frequently exposed to moisture and cooling is not covered.
e.g. The pipe installed at a corridor of a dormitory and studio or near an exit that opens and closes frequently.
- The place where the pipe is installed is highly humid due to the lack of ventilation system.
Drainpipe and drain hose installation
Care must be taken when installing the drain hose for the indoor unit to ensure that any condensate
water is correctly drained outside.
The drain hose can be installed to the right of the base pan.
1
Installing the drain hose should be the shorter, the better.
◆ In order to discharge condensation water, the drain hose should keep tilted.
◆ Fix the drain hose with Cable-Tie, so that it will not separate from the machine.
◆ While using draining pump, connect the end with draining pump.
2
Insulate and fix the drain hose according to the figure.
◆ Insert the drain hose to bottom of the outfall of water basin.
◆ Lock steel ring of the drain hose according to the figure.
◆ Wind and wrap steel ring and drain hose fully with thermal insulation sponge; fix both ends of external layer with ribbon for thermal insulation.
◆ After being installed, drain hose must be insulated fully by heat insulating material. (To be provided
at site.)
Fix with Cable-Tie
Indoor unit
Steel ring of drain hose
Joint of drain hose
Drain hose
A-A’
Wrap thermal sleeve hose
20
Drain hose
As shown in the figure,
tighten steel ring of the
drain hose.
Drainpipe and drain hose installation
Drainpipe Connection
Without the drain pump
ENGLISH
1. Install horizontal drainpipe with a slope of 1/100 or more and fix it by hanger space of 1.0~1.5m.
2. Install U-trap at the end of the drainpipe to prevent a nasty smell to reach the indoor unit.
3. Do not install the drainpipe to upward position. It may cause water flow back to the unit.
1~1.5m
Hanger
Flexible hose
Ceiling
Horizontal drainpipe
more than 1/100 slope
With the drain pump
1. The drain pipe should be installed within 300mm to 550mm from the flexible hose and then lift down 20mm
or more.
2. Install horizontal drainpipe with a slope of 1/100 or more and fix it by hanger space of 1.0~1.5m.
3 Install the air vent in the horizontal drainpipe to prevent water flow back to the indoor unit.
• You may not need to install it if there were proper slope in the horizontal drainpipe.
4 The flexible hose should not be installed upward position,
it may cause water flow back to the indoor unit.
Air vent
200mm
or more
300mm or less
20mm
or more
Within
300~550mm
Flexible hose Ceiling
1~1.5m
Hanger
Horizontal drainpipe
more than 1/100 slope
21
Drainpipe and drain hose installation
Centralized Drainage
Without the drain pump
Install horizontal drainpipe with a slope of 1/100 or more and fix it by hanger space of 1.0~1.5m.
2
Install U-trap at the end of the drainpipe to prevent a nasty smell to reach the indoor unit.
100mm or more
1
Ceiling
Horizontal drainpipe
more than 1/100 slope
With the drain pump
1
Install main air vent at the front of the farthest indoor unit from the main drain when installed
indoor units are more than 3.
2
You may need to install individual air vent to prevent water flow back at the top of each indoor unit
drainpipe.
1~1.5m
Hanger
Individual
air vent
Main drainpipe
550mm or
less
Centralized horizontal drainpipe
(more than 1/100 slope)
Testing the drainage
Prepare a little water about 2 liter.
1
Pour water into the base pan in the indoor unit as shown in figure.
2
Confirm that the water flows out through the drain hose.
22
Main air vent
G_6
Wiring work
Power and communication cable connection
1. Before wiring work, you must turn off all power source.
ENGLISH
2. Indoor unit power should be supplied through the breaker( ELCB or MCCB+ELB ) separated by the
outdoor power.
ELCB:Earth Leakage Circuit Breaker
MCCB:Molded Case Circuit Breaker
ELB:Earth Leakage Breaker
3. The power cable should be used only copper wires.
4. Connect the power cable{1(L), 2(N)} among the units within maximum length and communication
cable(F1, F2) each.
5. Connect F3, F4(for communication) when installing the wired remote control.
Outdoor Unit
Wired Remote
Control
220-240V~
or
ELCB
Indoor Unit 1
Indoor Unit 2
V2
L
V1
Indoor Unit 3
h ELCB : Essential Installation
WARNING :
Power off before connecting any wires;
Indoor PBA will be damaged while V1,V2,F3,F4 short each
other.
EEV kit
N
MCCB+
ELB
N
Indoor Unit 4
Indoor Unit 5
L
N
L
N
L
Indoor Unit 6
h Ceiling, wall-mounted indoor unit.
Selecting compressed ring terminal
Silver solder
B
D
d1
E
F
L
d2
t
Norminal Norminal
Standard
Standard
Standard
dimensions dimensions Standard
Allowance
Allowance
Allowance
Allowance
dimension
dimension
Min. Min. Max. dimension
Min.
for cable for screw dimension
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm2)
(mm)
4
6.6
+0.3
+0.2
1.5
±0.2
3.4
1.7
±0.2
4.1
6
16
4.3
0.7
4
8
-0.2
0
4
6.6
+0.3
+0.2
2.5
±0.2
4.2
2.3
±0.2
6
6 17.5
4.3
0.8
4
8.5
-0.2
0
+0.3
+0.2
4
4
9.5
±0.2
5.6
3.4
±0.2
6
5
20
4.3
0.9
-0.2
0
23
Wiring work
Specification of electronic wire
Power supply
MCCB
Max : 242V
Min : 198V
XA
ELB or ELCB Power cable Earth cable
X A, 30mmA
0.1 s
2.5mm2
2.5mm2
Communication cable
0.75~1.5mm2
 Decide the capacity of ELCB(or MCCB+ELB) by below formula.
 Power supply cords of parts of appliances for outdoor use shall not be lighter than polychloroprene
sheathed flexible cord.
(Code designation IEC:60245 IEC 57 / CENELEC:H05RN-F ; IEC:60245 IEC 66 / CENELEC:H07RN-F)
The capacity of ELCB(or MCCB+ELB) X [A] = 1.25 X 1.1 X ∑Ai
T X : The capacity of ELCB(or MCCB+ELB).
T ∑Ai : Sum of Rating currents of each indoor unit.
T Refer to each installation manual about the rating current of indoor unit.

Decide the power cable specification and maximum length within 10% power drop among indoor units.
n
Coef×35.6×Lk×ik
k=1
1000×Ak
∑(
) < 10% of input voltage[V]
T coef: 1.55
T Lk: Distance among each indoor unit[m], Ak: Power cable specification[mm2]
ik: Running current of each unit[A]
24
Easy Tuning
EASY Tuning
ENGLISH
If the more cooling and heating airflow rate which set up when installing is wanted, or if the more Silent operation
which sets up when installing is wanted, air conditioner is tuned for comfort.
Indoor unit airflow rate for high, mid, low mode increases or decreases for +2 ~ -2 Steps with wired remocon.
SEG Used
Main Menu Sub-menu
12 34
56
1. Press the User Set button.
 (Main Menu) will be displayed, and you can press the [Λ]/
[V] buttons to select No. 8, which will set the Easy Tuning.
2. Press the [>] button to select airflow step.
 Press the [Λ]/[V] buttons to select airflow step(-2,-1,0,1,2)
tuning (During the Easy Tuning setting, AC Fan Speed icon
will be displayed)
Away/MDS
3) Press the
button to complete the Easy Tuning.
(When the Easy Tuning setting complete, AC Fan Speed icon will be off)
4) Press the
Main menu
8
NOTE
button to to exit to normal mode.
Sub menu
-
Functions
Easy Tuning
SEG used
1,2
Default
Range
0
-2 : -2 Step
-1 : -1 Step
0 : No Use
1 : +1 Step
2 : +2 Step
• Press the
button anytime during setup to exit without setting.
• According to airflow changed from the Easy Tuning,Air conditioning performance reducing is
possible.
25
Setting the indoor unit option code
In order to set the indoor unit option code use the wired remote controller and follow the directions below.
Data bit
Main Menu Sub-menu
12 34
Page number
Option Code
12 34
56
SEG1
0
56
SEG2
SEG3
SEG4
SEG5
SEG6
✴
✴
✴
✴
✴
Page number
SEG7
1
SEG8
SEG9
✴
✴
SEG10 SEG11 SEG12
✴
✴
✴
Page number
SEG13 SEG14 SEG15 SEG16 SEG17 SEG18
✴
✴
✴
✴
✴
2
Page number
Away/MDS
SEG19 SEG20 SEG21 SEG22 SEG23 SEG24
✴
✴
✴
✴
✴
3
Page number
1) Press the
displayed.
and
2) Press the
/
button to select
and then press
button to enter a Sub-menu setting screen.
3) Press the
screen.
/
button to select
and then press
button to enter a Indoor unit option code setting
NOTE
buttons at the same time for more than 3 seconds and then a Main menu will be
• The first digit represents the page number and the remaining five digits are option codes.
• The option code which is currently setting will flicker.
4) Press the
/
5) Press the
button to save and complete the option setting.
6) Press the
button to exit to normal mode.
NOTE
• Press the
button to set the option code in order. Press
button to go to the next page.
button anytime during setup to exit without setting.
• Option code will not be applied if you don’t press the
• Setting indoor unit option code is only possible in Master wired remote controller.
You can only check the indoor unit option code in Slave wired remote controller.
• Setting indoor unit option code is possible when one indoor unit is connected. If more than 2
indoor units are connected, you can only check the Master indoor unit option code.
26
Setting an indoor unit address and installation option
Set the indoor unit address and installation option with remote controller option. Set the each option
separately since you cannot set the ADDRESS setting and indoor unit installation setting option at the same
time. You need to set twice when setting indoor unit address and installation option.
1) Press the
displayed.
and
2) Press the
/
button to select
3) Press the
/
button to select and then press
ENGLISH
Setting an indoor unit address
buttons at the same time for more than 3 seconds and then a Main menu will be
and then press
button to enter a Sub-menu setting screen.
button to enter a Indoor Address setting screen.
Data bit
12 34
NOTE
56
• The Main/RMC Address which is currently setting will flicker.
• Data bit 1 and 2 present Indoor unit main address checking
• Data bit 3 and 4 present Indoor unit main address setting(outdoor unit reset is needed to set).
• Data bit 5 and 6 present Indoor unit RMC address setting/checking.
4) Press the
/
5) Press the
button to save and complete the option setting.
6) Press the
button to exit to normal mode.
• Press the
NOTE
button to set the Indoor unit Main/RMC Address.
button anytime during setup to exit without setting.
• Address will not be applied if you don't press
button.
• Setting Main/RMC Address of an Indoor unit is available only with a master wired remote controller.
Setting an indoor unit installation option
In order to check and set the indoor unit installation option code use the wired remote controller and follow
the directions below.
1) Press the
displayed.
and
2) Press the
/
buttons at the same time for more than 3 seconds and then a Main menu will be
button to select
and then press
button to enter a Sub-menu setting screen.
3) Press the
/
button to select
code setting screen.
and then press
button to enter a Indoor unit installation option
27
Setting an indoor unit address and installation option
NOTE
• The first digit represents the page number and the remaining five digits are installation option.
• The total option codes are 24 digits. You can set six digits at a time and it is distinguished by page
number (0, 1, 2, 3).
4) Press the
SEG1
0
SEG7
1
SEG13
2
SEG19
3
/
button to set the installation option code in order. Press
button to go to the next page.
SEG2
SEG3
SEG4
SEG5
SEG6
External room
temperature sensor
FAN RPM
/ Minimizing fan
2
-Central control
compensation
operation when
thermostat is off
SEG8
SEG9
SEG10
SEG11
SEG12
EEV Step when
Drain pump
Hot water heater
--heating stops
SEG14
SEG15
SEG16
SEG17
SEG18
External control
Number of hours
output / External
External control
S-Plasma ion
Buzzer
heater On or Off
using filter
signal
SEG20
SEG21
SEG22
SEG23
SEG24
Heating setting
compensation
EEV Step of stopped
Individual control of a
/ Removing
unit during oil return/ Motion detect sensor
-remote controller
condensated water in
defrost mode
heating mode
5) Press the
button to save and complete the option setting.
6) Press the
button to exit to normal mode.
• Press
NOTE
28
button anytime during setup to exit without setting.
• Option code will not be applied if you don't press
button.
• Setting Installation option code is available only with a master wired remote controller.
• Setting Installation option code is available when there is one on one connection between a wired
remote controller and an indoor unit.
Set the indoor unit address and installation option with remote controller option.
Set the each option separately since you cannot set the ADDRESS setting and indoor unit installation setting
option at the same time. You need to set twice when setting indoor unit address and installation option.
ENGLISH
The procedure of option setting
Air flow direction (Up and down)
Adusts the air flow direction up and
down (Not applicable to Duct type
models).
Mode
Selects operation mode.
Power
Turns the air conditioner on
or off.
Temperature
Adjusts the temperature.
Fan speed
Adjusts the fan speed.
Options
Selects options during
operation.
Air flow direction (Left and right)
Adjusts the air flow direction left and
right.
Settings
Selects settings.
Timer
Sets timer option.
SET
Selects or cancels an option.
Direction
Moves to select and set an
option.
Step 1. Entering mode to set option
1. Remove batteries from the remote controller.
2. Insert batteries and enter the option setting mode while pressing High Temp button and Low Temp button.
Auto
3.
Check if you have entered the option setting status.
On
Step 2. The procedure of option setting
After entering the option setting status, select the option as listed below.
• Option setting is available from SEG1 to SEG 24
• SEG1, SEG7, SEG13, SEG19 are not set as page option.
• Set the SEG2~SEG6, SEG8~SEG12 as ON status and SEG14~18, SEG20~24 as OFF status.
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12
0
X
X
X
X
X
1
X
X
X
X
X
SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24
2
X
X
X
X
X
3
X
X
X
X
On(SEG1~12)
Auto
On
Off(SEG13~24)
Auto
Off
X
29
Setting an indoor unit address and installation option
Option setting
1. Setting SEG2, SEG3 option
Press Low Fan button(∨) to enter SEG2 value.
Press High Fan button(∧) to enter SEG3 value.
Each time you press the button,   …  will be selected in rotation.
Status
Auto
Auto
On
On
SEG2
SEG3
2. Setting Cool mode
Cool
Press Mode button to be changed to Cool mode in the ON status.
3. Setting SEG4, SEG5 option
Press Low Fan button(∨) to enter SEG4 value.
Press High Fan button(∧) to enter SEG5 value.
Each time you press the button,   …  will be selected in rotation.
On
Cool
Cool
On
On
SEG4
SEG5
Dry
4. Setting Dry mode
On
Press Mode button to be changed to DRY mode in the ON status.
5. Setting SEG6, SEG8 option
Press Low Fan button(∨) to enter SEG6 value.
Press High Fan button(∧) to enter SEG8 value.
Each time you press the button,   …  will be selected in rotation.
Dry
On
SEG6
6. Setting Fan mode
SEG8
Fan
Press Mode button to be changed to FAN mode in the ON status.
7. Setting SEG9, SEG10 option
Press Low Fan button(∨) to enter SEG9 value.
Press High Fan button(∧) to enter SEG10 value.
Each time you press the button,   …  will be selected in rotation.
On
Fan
Fan
On
On
SEG9
8. Setting Heat mode
SEG10
Heat
On
Press Mode button to be changed to HEAT mode in the ON status.
9. Setting SEG11, SEG12 option
Press Low Fan button(∨) to enter SEG11 value.
Press High Fan button(∧) to enter SEG12 value.
Each time you press the button,   …  will be selected in rotation.
Heat
Heat
On
On
SEG11
Off
Press Mode button to be changed to AUTO mode in the OFF status.
30
SEG12
Auto
10. Setting Auto mode
11. Setting SEG14, SEG15 option
Press Low Fan button(∨) to enter SEG14 value.
Press High Fan button(∧) to enter SEG15 value.
Each time you press the button,   …  will be selected in rotation.
Dry
On
Auto
Auto
Off
Off
SEG14
SEG15
Option setting
Status
12. Setting Cool mode
Cool
Press Mode button to be change to Cool mode in the OFF status.
Off
ENGLISH
13. Setting SEG16, SEG17 option
Press Low Fan button(∨) to enter SEG16 value.
Press High Fan button(∧) to enter SEG17 value.
Each time you press the button,   …  will be selected in rotation.
Cool
Cool
Off
Off
SEG16
SEG17
Dry
14. Setting Dry mode
Off
Press Mode button to be change to Dry mode in the OFF status.
15. Setting SEG18, SEG20 option
Press Low Fan button(∨) to enter SEG18 value.
Press High Fan button(∧) to enter SEG20 value.
Each time you press the button,   …  will be selected in rotation.
Dry
Dry
Off
Off
SEG18
16. Setting Fan mode
SEG20
Fan
Off
Press Mode button to be change to Fan mode in the OFF status.
17. Setting SEG21, SEG22 option
Press Low Fan button(∨) to enter SEG21 value.
Press High Fan button(∧) to enter SEG22 value.
Each time you press the button,   …  will be selected in rotation.
Fan
Fan
Off
Off
SEG21
18. Setting Heat mode
SEG22
Heat
Off
Press Mode button to be change to HEAT mode in the OFF status.
19. Setting SEG23, SEG24 mode
Press Low Fan button(∨) to enter SEG23 value.
Press High Fan button(∧) to enter SEG24 value.
Each time you press the button,   …  will be selected in rotation.
Heat
Heat
Off
Off
SEG23
SEG24
Step 3. Check the option you have set
After setting option, press
Auto
On

Dry

On
Auto
Off
button to check whether the option code you input is correct or not.
Cool
Dry
Cool

Off
Fan

On

Off
On
Heat

Fan

Off

On
Heat

Off
Step 4. Input option
Press operation button
with the direction of remote control for set.
For the correct option setting, you must input the option twice.
Step 5. Check operation
1. Reset the indoor unit by pressing the RESET button of indoor unit or outdoor unit.
2. Take the batteries out of the remote controller and insert them again and then press the operation button.
31
Setting an indoor unit address and installation option
Setting an indoor unit address (MAIN/RMC)
Indoor Unit
1(L)
2(N)
1. Check whether power is supplied or not.
F2
F1
- When the indoor unit is not plugged in, there should be additional
power supply in the indoor unit.
2. The panel(display) should be connected to an indoor unit to receive option.
3. Before installing the indoor unit, assign an address to the indoor unit according to the air
conditioning system plan.
4. Assign an indoor unit address by wireless remote controller.
- The initial setting status of indoor unit ADDRESS(MAIN/RMC) is “0A0000-100000-200000-300000”.
Option No. : 0AXXXX-1XXXXX-2XXXXX-3XXXXX
Option
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
Explanation
PAGE
Mode
Setting Main address
100-digit of indoor
unit address
10-digit of indoor
unit
The unit digit of
an indoor unit
Remote
Controller
Display
Auto
Auto
On
On
Dry
Cool
Cool
On
On
On
Indication Details Indication Details Indication Details Indication Details Indication Details Indication Details
Indication
and Details
0
Option
SEG7
Explanation
PAGE
No Main
address
1
Main
address
setting
mode
A
SEG8
SEG9
0~9
100-digit
0~9
SEG10
Setting RMC address
Remote
Controller
Display
SEG12
Group channel(*16)
Group address
0
No RMC
address
1
RMC
address
setting
mode
1
Heat
On
On
Indication Details
__
A unit
digit
0~9
Heat
On
__
10-digit
SEG11
Fan
Indication Details
Indication
and Details
0
Indication Details Indication Details
RMC1
0~F
RMC2
0~F
• When “A”~”F” is entered to SEG5~6, the indoor unit MAIN ADDRESS is not changed.
• If you set the SEG 3 as 0, the indoor unit will maintain the previous MAIN ADDRESS even if you
input the option value of SEG5~6.
• If you set the SEG 9 as 0, the indoor unit will maintain previous RMC ADDRESS even if you input
the option value of SEG11~12.
• You cannot set SEG11 and SEG12 as F value at the same time.
32
Setting an indoor unit installation option
(suitable for the condition of each installation location)
1. Check whether power is supplied or not.
1(L)
2(N)
ENGLISH
Indoor Unit
- When the indoor unit is not plugged in, there should be additional
power supply in the indoor unit.
F2
F1
2. The panel(display) should be connected to an indoor unit to receive
option.
3. Set the installation option according to the installation condition of an air conditioner.
- The default setting of an indoor unit installation option is
“020010-100000- 200000-300000”.
- Individual control of a remote controller(SEG20) is the function that controls an
indoor unit individually when there is more than one indoor unit.
4. Set the indoor unit option by wireless remote controller.
 02 series installation option
SEG1
SEG2
SEG3
0
2
--
SEG7
SEG8
SEG9
SEG4
External room
temperature sensor
/ Minimizing fan
operation when
thermostat is off
SEG10
SEG5
SEG6
Central control
SEG11
SEG12
--
FAN RPM
compensation
1
Drain pump
Hot water heater
--
EEV Step when
heating stops
SEG13
SEG14
SEG16
SEG17
SEG18
2
External control
S-Plasma ion
Buzzer
Number of hours
using filter
SEG19
SEG20
SEG15
External control
output / External
heater On or Off
signal
SEG21
SEG22
SEG23
SEG24
3
Individual control of
a remote controller
Motion detect
sensor
--
Heating setting
compensation
EEV Step of stopped
/ Removing
unit during oil return/
condensated water in
defrost mode
heating mode

1WAY/2WAY/4WAY MODEL : Drain pump(SEG8) will be set to ‘USE + 3minute delay’ even if the drain
pump is set to 0.

1 WAY/2WAY/4WAY,DUCT MODEL : Number of hours using filter(SEG18) will be set to ‘1000hour’ even
if the SEG18 is set to exept for 2 or 6.

When setting the option other than above SEG values, the option will be set as “0”.
 SEG5 central control option is basically set as 1 (Use), so you don’t need to set the central control
option additionally.
However, if the central control is not connected but it doesn’t indicate an error message, you need to
set the central control option as 0 (Disuse) to exclude the indoor unit from the central control.
33
Setting an indoor unit address and installation option
 The output of hot water heater in SEG9 is generated from the hot coil part of the terminal board in duct models.
* The output of hot coil terminal is AC 220 V / 230 V
(The same as Indoor Unit’s input Power)
F1
F2
COM1
V1
(+)
F3
V2
(-)
F4
1(L) 2(N) 1
L
COM2
2
N
OUTDOOR
Remote
AC
DC 12 V Wire
Controller POWER
COMMUNICATION
HOT
COIL
 The external output of SEG15 is generated by MIM-B14 connection. (Refer to the manual of MIM-B14.)
 02 series installation option(Detailed)
Option No. : 02XXXX-1XXXXX-2XXXXX-3XXXXX
Option
Explanation
SEG1
PAGE
Remote
Controller
Display
SEG2
SEG3
MODE
Use of robot
cleaning
Auto
Auto
On
On
SEG4
Use of external room temperature
sensor / Minimizing fan operation when
thermostat is off
SEG5
SEG6
Use of central control
FAN RPM compensation
Dry
Cool
Cool
On
On
On
Details
Indication Details Indication
Details
Indication
and Details
0
2
Use of
Indication Details Indication External
room
temperature
sensor
0
Disuse
0
Disuse
1
Use
1
Use
Option
SEG7
SEG8
SEG9
Explanation
PAGE
Use of drain pump
Use of hot water
heater
Dry
Remote
Controller
Display
Indication
and Details
34
Details
Details
Disuse
0
Disuse
Disuse
Use
Use (*1)
Use (*1)
1
Use
SEG10
SEG11
Details
0
Disuse
RPM
compensation
1
High ceiling
KIT
2
SEG12
Heat
On
Indication Details Indication
Disuse
0
Disuse
1
Use
1
Use (*2)
2
--
2
When an indoor
unit stops, drain
pump will operate
for 3min
Details
Indication
0
1
3
Indication
EEV Step when heating
stops
Fan
0
1
Indication
Disuse
On
On
Indication Details Indication
2
3
Minimizing fan
operation when
thermostat is off
Use (*2)
Details
Default
value
Noise
decreasing
setting
Indication
Details
Option
SEG13
SEG14
Explanation
PAGE
Use of external control
Auto
Auto
Off
Off
SEG16
SEG17
SEG18
S-Plasma ion
Buzzer control
Hours of filter usage
Cool
Dry
Cool
Off
Off
Off
Details
Setting the
External Indication Details Indication
Indication Details Indication Details Indication output of
Details
heater On/Off
external
signal
control
0
Disuse
0
Thermo on
0
Disuse
0
Use buzzer
Indication
ON/OFF
Operation
and Details
1
1
1
Disuse buzzer
control
on
OFF
2
2
2
Use (*3)
control
1
Use
Window
3
ON/OFF
3
Use (*3)
control
Option
SEG19
SEG20
SEG21
SEG22
SEG23
EEV Step of stopped
Individual control of a Heating setting compensation / Removing
Explanation
PAGE
unit during oil return/
Motion detect sensor
remote controller
condensated water in heating mode
defrost mode
Dry
Remote
Controller
Display
Off
Fan
Fan
Off
Off
Details
Removing
Indication Details Indication Details Indication Heating Setting Condensated Indication
Water in
Compensation
Heating
Mode
Details
Default
value
Indication
Details
0
Disuse
Turn out in 30min.
without motion
Turn out in 60min.
without motion
Turn out in 120min.
without motion
0
Default (*4)
Disuse
2
channel 2
1
2 °C
Disuse
2
3
channel 3
2
5 °C
Disuse
3
3
Default (*4)
Use (*5)
4
4
2 °C
Use (*5)
1
4
channel 4
5
5 °C
Use (*5)
Details
2
1000 Hour
6
2000 Hour
SEG24
-
Heat
channel 1
3
Indication
Off
0 or 1
Indication
and Details
0
ENGLISH
Remote
Controller
Display
SEG15
Setting the output of external control /
External heater On/Off signal
Oil return
or Noise
decreasing
in defrost
mode
1
5
6
7
8
Turn out in 180min.
without motion
Turn out in 30min.
without motion or
*advanced function
Turn out in 60min.
without motion or
*advanced function
Turn out in 120min.
without motion or
*advanced function
Turn out in 180min.
without motion or
*advanced function
35
Setting an indoor unit address and installation option
*
Advanced function: Controlling cooling/heating current or power saving with motion detect.
(*1) Minimizing fan operation when thermostat is off
- Fan operates for 20 seconds at an interval of 5 minutes in heat mode.
(*2) 1: Fan is turned on continually when the hot water heater is turned on,
3: Fan is turned off when the hot water heater is turned on with cooling only indoor unit
Cooling only indoor unit: To use this option,install the Mode Select switch(MCM-C200) on the outdoor unit and fix it as cool mode.
(*3) When the following 2 or 3 is used as external heater On/Off signal, the signal for monitoring external contact control will not be output.
2: Fan is turned on continually when the external heater is turned on,
3: Fan is turned off when the external heater is turned on with cooling only indoor unit
Cooling only indoor unit: To use this option,install the Mode Select switch(MCM-C200) on the outdoor unit and fix it as cool mode.
· If Fan is set to off for cooling only indoor unit by setting the SEG9=3 or SEG15=3, you need to use an external sensor or wired remote
controller sensor to detect indoor temperature exactly.
(*4) Default setting value
- 4Way Cassette, Mini 4Way Cassette: 5 °C
- Other indoor units: 2 °C
(*5) This function can be applied to 4 Way Cassette and Mini 4 Way Cassette only. If the air conditioner operates the heating mode
immediately after finishing the cooling mode, the condensated water in the drain pan becomes water vapor by the heat of the indoor
unit heat exchanger. Since the water vapor might be condensed on the indoor unit, which may fall into a living space, use this function to
get rid of the water vapor out of the indoor unit by operating the fan (for maximum 20 minutes) even when the indoor unit is turned off
after cooling mode is turned to heating mode .
• Do not install the electronic heater in the flow channel of the indoor unit fan.
Electronic heater should
not be installed.
Discharge side
Suction side
Air Flow
Duct Indoor unit
 05 series installation option
SEG1
SEG2
SEG3
0
5
Use of Auto Change Over for
HR only in Auto mode
SEG7
SEG8
SEG9
1
(When setting SEG3)
Standard for mode change
Cooling → Heating
(When setting SEG3)
Time required for mode
change
SEG13
SEG14
SEG15
SEG4
SEG5
SEG6
(When setting SEG3)
Standard heating temp.
Offset
SEG10
Compensation option for
Long pipe or height
difference between indoor
units
(When setting SEG3)
Standard cooling temp.
Offset
SEG11
(When setting SEG3)
Standard for mode change
Heating → Cooling
SEG12
-
-
SEG16
SEG17
SEG18
2
-
-
-
-
Control variables when using
hot water / external heater
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
3
-
-
-
-
-
36
 05 series installation option(Detailed)
Option No. : 05XXXX-1XXXXX-2XXXXX-3XXXXX
Option
SEG2
PAGE
SEG3
Use of Auto Change
Over for HR only in
Auto mode
MODE
Remote
Controller
Display
Auto
Auto
On
On
Indication Details Indication
Details
0
Explanation
SEG8
PAGE
(When setting SEG3)
Standard for mode
changing Cooling →
Heating mode
Dry
Remote
Controller
Display
On
Indication Details Indication
Indication
and Details
Details
Dry
Cool
Cool
On
On
On
Indication
Details
Indication
Details
0
0°C
0
0°C
0
1°C
Use Auto
Change
Over for
HR only
1
2
3
4
5
6
7
0.5°C
1°C
1.5°C
2°C
2.5°C
3°C
3.5°C
1
2
3
4
5
6
7
0.5°C
1°C
1.5°C
2°C
2.5°C
3°C
3.5°C
1
2
3
4
5
6
7
1.5°C
2°C
2.5°C
3°C
3.5°C
4°C
4.5°C
SEG9
SEG10
(When setting SEG3)
Time required for
mode change
Compensation option
for Long pipe or height
diffference between
indoor units
Fan
Fan
On
On
Indication Details Indication
0
1°C
0
5 min.
1
1.5°C
1
7 min.
2
2°C
2
9 min.
3
2.5°C
3
11 min.
4
3°C
4
13 min.
5
3.5°C
5
15 min.
6
4°C
6
20 min.
7
4.5°C
7
30 min.
0
1
1
(When setting SEG3)
Standard cooling temp.
Offset
Details
5
SEG7
SEG6
(When setting SEG3)
Standard for mode
change
Heating → Cooling
Follow
product
option
1
Option
(When setting SEG3)
Standard heating
temp. Offset
SEG5
Indication Details Indication
0
Indication
and Details
SEG4
2
SEG11
SEG12
Details
Use default
value
1) Height
difference1)
is more than
30m or
2) Distance2)
is longer than
110m
1) Height
difference1) is
15~30m or
2) Distance2) is
50~110m
37
ENGLISH
Explanation
SEG1
Setting an indoor unit address and installation option
Option
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18(*3)
Explanation
Control variables when using hot water / external heater
Dry
Remote
Controller
Display
Off
Indication
Indication
and Details
2
Details
Set temp. for heater On/Off
Delay time for heater On
0
At the same time as thermo on
No delay
1
At the same time as thermo on
10 minutes
2
At the same time as thermo on
20 minutes
3
1.5 °C
No delay
4
1.5 °C
10 minutes
5
1.5 °C
20 minutes
6
3.0 °C
No delay
7
3.0 °C
10 minutes
8
3.0 °C
20 minutes
9
4.5 °C
No delay
A
4.5 °C
10 minutes
20 minutes
B
4.5 °C
C
6.0 °C
No delay
D
6.0 °C
10 minutes
E
6.0 °C
20 minutes
(*1) Height difference : The difference of the height between the corresponding indoor uint and the indoor unit installed at the lowest place.
For example, When the indoor unit is installed 40m higher than the indoor unit installed at the lowest place, select the
option "1".
(*2) Distance : The difference between the pipe length of the indoor unit istalled at farthest place from an outdoor unit and the pipe length of the
corresponding indoor unit from an outdoor unit.
For example, when the farthest pipe length is 100 m(328 ft) and the corresponding indoor unit is 40 m away from an outdoor unit,
select the option "2".
(100 - 40 = 60m)
(*3) Heater operation when the SEG9 of 02 series installation option is set to using hot water heater or when SEG15 is set to using external heater
e.g. 1) S etting 02 series SEG9 =”1” / Setting 05 series SEG18 = “0”: Hot water heater is turned on at the same time as the heating thermostat
is on, and turned off when the heating thermostat is off.
e.g. 2) Setting 02 series SEG15 =”2” / Setting 05 series SEG18 =”A”:
Room temp. ≤ set temp. + f(heating compensation temp.)
- External heater is turned on when the temperature is maintained as 4.5 °C for 10 minutes. Room temp. > set temp. + f(heating compensation temp.)
- External heater is turned off when the temperature is maintained as 4.5 °C + 1 °C (1 °C is the Hysteresis for On/Off selection.)
38
SEG 3, 4, 5, 6, 8, 9 additional information
Heating Thermo On
Heating Thermo Off
Cooling Thermo On
ENGLISH
Cooling Thermo Off
When the SEG 3 is set as "1" and follow Auto Change Over for HR only operation, it will operate as follows.
Standard temp. for
Heating → Cooling
Temp.
c
b
Standard temp.
for Cooling
Ts
B
A
Set temp.
for Auto mode
C
D
a
Standard temp.
for Heating
d
Standard temp.
for Cooling →
Heating
A : Set with SEG4
B : Set with SEG5
C : Set with SEG6
D : Set with SEG8
Cooling/Heating mode can be changed when Thermo Off status is maintained during the time with SEG9.
39
Setting an indoor unit address and installation option
Changing a particular option
You can change each digit of set option.
Option
SEG1
SEG2
Explanation
PAGE
MODE
Remote
Controller
Display
SEG3
SEG4
SEG5
SEG6
The tens’ digit of an The unit digit of an
The option mode
option SEG you will option SEG you will
you want to change
change
change
Auto
Auto
On
On
Changed value
Dry
Cool
Cool
On
On
On
Indication Details Indication Details Indication Details Indication Details Indication Details Indication Details
Indication and
Details
NOTE
0
D
Option
mode
1~6
Tens’ digit
of SEG
0~9
Unit digit
of SEG
0~9
The
changed
value
• When changing a digit of an indoor unit address setting option, set the SEG3 as ‘A’.
• When changing a digit of indoor unit installation option, set the SEG3 as ‘2’.
Ex) When setting the ‘buzzer control’ into disuse status.
Option
SEG1
SEG2
Explanation
PAGE
MODE
Indication
0
D
SEG3
SEG4
The tens’ digit of an
The option mode you
option SEG you will
want to change
change
2
1
SEG5
SEG6
The unit digit of an
option SEG you will
change
Changed value
7
1
• If you are using heat pump model, mixed operation mode (two or more indoor units operating
in different operation mode simultaneously) is not available when the indoor units are
connected to same outdoor unit. If you set the master indoor unit with a remote controller,
outdoor unit will operate in the mode which was set in the master indoor unit.
40
0~F
Note
ENGLISH
41
QUESTIONS OR COMMENTS?
COUNTRY
CALL
AUSTRIA
0800 - SAMSUNG (0800 - 7267864)
BELGIUM
02-201-24-18
OR VISIT US ONLINE AT
COUNTRY
CALL
www.samsung.com/be/support (Dutch)
UKRAINE
0-800-502-000
(French)
MOLDOVA
0-800-614-40
051 331 999
www.samsung.com/support
U.A.E
800-SAMSUNG (800 - 726 7864)
BULGARIA
800 111 31 , Безплатна телефонна линия
www.samsung.com/bg/support
OMAN
800-SAMSUNG (800 - 726 7864)
CROATIA
072 726 786
www.samsung.com/hr/support
KUWAIT
183-CALL (183-2255)
CZECH
800 - SAMSUNG (800-726786)
www.samsung.com/cz/support
BAHRAIN
8000-GSAM (8000-4726)
DENMARK
70 70 19 70
www.samsung.com/dk/support
QATAR
800-CALL (800-2255)
FINLAND
030-6227 515
www.samsung.com/fi/support
FRANCE
01 48 63 00 00
www.samsung.com/fr/support
ITALIA
www.samsung.com/n_africa/support
0800-Samsung (72678) www.samsung.com/pk/support
TUNISIA
80-1000-12 www.samsung.com/n_africa/support
Mobilfunk max. 0,60 €/Anruf)
[HHP] 0180 6 M SAMSUNG bzw.
www.samsung.com/de/support
8009 4000 only from landline, toll free
80111-SAMSUNG (80111 726 7864) only from land line www.samsung.com/gr/support
0680SAMSUNG (0680-726-786)
0680PREMIUM (0680-773-648)
800-SAMSUNG(800.7267864)
[HHP] 800.Msamsung (800.67267864)
http://www.samsung.com/hu/support
www.samsung.com/it/support
020 405 888
www.samsung.com/support
080 697 267
090 726 786
800-22273
www.samsung.com/Levant/support
065777444
(English)
SYRIA
18252273
IRAN
021-8255
www.samsung.com/iran/support
MOROCCO
080 100 2255
www.samsung.com/n_africa/support
SAUDI ARABIA
920021230
TURKEY
444 77 11
www.samsung.com/tr/support
ARGENTINE
0800-333-3733
www.samsung.com/ar/support
URUGUAY
000 405 437 33
www.samsung.com/latin/support (Spanish)
PARAGUAY
009 800 542 0001
www.samsung.com/nl/support
NORWAY
www.samsung.com/no/support
815 56480
0 801-172-678* lub +48 22 607-93-33 **
[HHP] 0 801-672-678* lub +48 22 607-93-33**
08008 726 78 64 (08008 SAMSUNG )
Apel GRATUIT
www.samsung.com/sa/support
www.samsung.com/sa_en/support (English)
COSTA RICA
DOMINICA
SLOVAKIA
0800 - SAMSUNG(0800-726 786)
www.samsung.com/sk/support
SWEDEN
0771 726 7864 (SAMSUNG)
SWITZERLAND
0848 726 78 64 (0800-SAMSUNG)
www.samsung.com/es/support
www.samsung.com/se/support
www.samsung.com/ch/support
(German)
www.samsung.com/ch_fr/support
(English)
0800-124-421 (Demais cidades e regiões)
4004-0000 (Capitais e grandes centros)
800-SAMSUNG(726-7864)
www.samsung.com/br/support
www.samsung.com/cl/support
[HHP] 02-24828200
800-10-7260
www.samsung.com/cl/support
[HHP] 4828210
Gratis desde cualquier parte del país 01 8000
www.samsung.com/co/support
112 112 ó desde su celular #SAM(726)
www.samsung.com/ro/support
www.samsung.com/rs/support
www.samsung.com/latin_en/support
Bogotá 600 12 72
COLOMBIA
011 321 6899
[HHP] 0034902167267
BOLIVIA
www.samsung.com/pt/support
SERBIA
0034902172678
CHILE
www.samsung.com/pl/support
** (koszt połączenia według taryfy operatora)
808 20 7267
BRAZIL
www.samsung.com/si/support
NETHERLANDS 0900-SAMSUNG (0900-7267864) (€ 0,10/Min)
SPAIN
JORDAN
(+30) 210 6897691 from mobile and land line
MONTENEGRO
ROMANIA
www.samsung.com/eg/support
16580
PAKISTAN
www.samsung.com/support
PORTUGAL
08000-726786
(*0,20 €/Anruf aus dem dt. Festnetz, aus dem
261 03 710
POLAND
www.samsung.com/ae_ar/support (Arabic)
0180 6 7267864*
LUXEMBURG
SLOVENIA
www.samsung.com/ae/support (English)
021 36 11 00
Mobilfunk max. 0,60 €/Anruf)
HUNGARY
EGYPT
www.samsung.com/support
ALGERIA
(*0,20 €/Anruf aus dem dt. Festnetz, aus dem
GREECE
www.samsung.com/ua_ru/support (Russian)
0180 6 SAMSUNG bzw.
0180 6 67267864*
CYPRUS
www.samsung.com/ua/support (Ukrainian)
www.samsung.com/be_fr/support
BOSNIA
GERMANY
OR VISIT US ONLINE AT
www.samsung.com/at/support
ECUADOR
EL SALVADOR
GUATEMALA
HONDURAS
(French)
JAMAICA
U.K
0330 SAMSUNG (7267864)
www.samsung.com/uk/support
EIRE
0818 717100
www.samsung.com/ie/support
LITHUANIA
8-800-77777
www.samsung.com/lt/support
LATVIA
8000-7267
www.samsung.com/lv/support
ESTONIA
800-7267
www.samsung.com/ee/support
PUERTO RICO
RUSSIA
8-800-555-55-55
www.samsung.com/ru/support
TRINIDAD &
NICARAGUA
PANAMA
TOBAGO
0-800-507-7267
00-800-1-SAMSUNG (726-7864)
1-800-751-2676
1-800-10-72670
www.samsung.com/latin/support (Spanish)
1-800-SAMSUNG (72-6786)
www.samsung.com/latin_en/support
800-6225
(English)
1-800-299-0013
1-800-299-0033
800-27919267
800-2791-9111
1-800-234-7267
www.samsung.com/latin_en/support
1-800-SAMSUNG (726-7864)
(English)
00-1800-5077267
800-7267
www.samsung.com/latin/support (Spanish)
800-0101
www.samsung.com/latin_en/support
1-800-682-3180
(English)
1-800-SAMSUNG(726-7864)
GEORGIA
0-800-555-555
www.samsung.com/support
ARMENIA
0-800-05-555
www.samsung.com/support
AZERBAIJAN
0-88-555-55-55
www.samsung.com/support
KAZAKHSTAN
8-10-800-500-55-500(GSM: 7799, VIP care 7700)
www.samsung.com/support
VENEZUELA
0-800-SAMSUNG (726-7864)
www.samsung.com/ve/support
UZBEKISTAN
8-10-800-500-55-500
www.samsung.com/support
AUSTRALIA
1300 362 603
www.samsung.com/au/support
KYRGYZSTAN
8-10-800-500-55-500
www.samsung.com/kz_ru/support
TADJIKISTAN
8-10-800-500-55-500
www.samsung.com/support
MONGOLIA
'7-495-363-17-00
www.samsung.com/support
BELARUS
810-800-500-55-500
www.samsung.com/support
0-800-777-08
PERU
(Delete) Desde celulares por favor llamar al
www.samsung.com/pe/support
número 336 8686
1-800-10-7267864 [PLDT]
PHILIPPINES
1-800-8-7267864 [Globe landline and Mobile]
www.samsung.com/ph/support
02-4222111 [Other landline]
SINGAPORE
SAMSUNG ELECTRONICS CO.,LTD.
501# Suhong East Road,Industrial Park,Suzhou,Jiangsu,China
Samsung Electronics (UK) Ltd, Euro QA Lab.
Blackbushe Business Park. Saxony Way, Yateley, Hampshire. GU46 6GG United Kingdom
1800-SAMSUNG(726-7864)
www.samsung.com/sg/support
AEEE Yönetmeliğine Uygundur
This product is RoHS compliant
Duct Type Series
Big Duct :
AM✴✴✴JNHF✴✴✴
Air Conditioner
user manual
This manual is made with 100% recycled paper.
imagine the possibilities
Thank you for purchasing this Samsung product.
DB68-05048A-00