Maxtor HVR-04E Installation guide

Add to my manuals
57 Pages

advertisement

Maxtor HVR-04E Installation guide | Manualzz

HVR-04E

Installation Guide

v 1.0

FCC Compliance Statement

Caution: Any changes or modifications in construction of this device which are not expressly approved the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION

1. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

2. Disposal of used batteries according to the general recommendations against the environmental pollution.

3. Do not throw the batteries into a fire, and do not heat, short-circuit or attempt to disassemble the batteries.

4. Do not attempt to recharge the batteries.

Important Notice

1. Do not place heavy objects on the top of the HVR-04E.

2. HVR-04E is for indoor use. It is not weatherproof. Use HVR-04E with referring to its environmental specifications (Temperature & Humidity). To clean the HVR-04E, gently wipe the outside with a clean dry cloth.

3. Be sure to use a DC adapter that is provided by Hunt Electronic USA, Inc. Connecting HVR-04E directly to an AC current will cause electric damages to HVR-04E.

4. Be careful not to drop the HVR-04E. Physical shocks may harm the product. In addition, be sure the

HVR-04E is secured after installation.

5. If HVR-04E does not operate properly, please contact the closest HUNT ELECTRONIC USA, INC. distributor for after sales service. Tampering or disassembling the product will void the warranty.

6. Security surveillance laws may differ for each country. Therefore, please contact the local region first to avoid any surveillance law violations.

HVR-04E TABLE OF CONTENTS

OVERVIEW ................................................................................................................................ 7

1. What is HVR-04E?.............................................................................................................. 7

2. Supplied Accessories........................................................................................................ 8

3. Description & Function ..................................................................................................... 9

INSTALLATION AND CONNECTION........................................................................................11

4. Connecting & Running HVR-04E.....................................................................................11

4.1. Connecting camera .....................................................................................................11

4.2. Connecting Monitor .................................................................................................... 12

4.3. Connecting Audio ....................................................................................................... 12

4.4. Supplying Power......................................................................................................... 14

5. Running OSD menu......................................................................................................... 15

5.1. Using menu ................................................................................................................ 15

5.2. Dialogue Box to Edit a Word....................................................................................... 16

6. Setting remote controller ................................................................................................ 17

6.1. Setting remote control DIP switch............................................................................... 17

6.2. Set ID of HVR-04E ..................................................................................................... 17

6.3. Selecting HVR-04E..................................................................................................... 18

6.4. Operable range of remote controller ........................................................................... 19

6.5. Loading the batteries into remote controller................................................................ 19

7. HVR-04E Configuration ................................................................................................... 20

7.1. Basic Configuration .................................................................................................... 20

7.2. Advanced Configuration ............................................................................................. 20

7.3. External Storage & Backup Configuration................................................................... 21

7.4. Internet/Intranet Configuration .................................................................................... 21

8. HVR-04E Basic Setting .................................................................................................. 22

8.1. Viewing Image ............................................................................................................ 22

8.2. Setting Date & Time.................................................................................................... 23

8.2.1. Time Zone ........................................................................................................... 23

4 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

TABLE OF CONTENTS HVR-04E

8.2.2. Daylight Saving ................................................................................................... 23

8.2.3. Time Format ........................................................................................................ 24

8.2.4. Date..................................................................................................................... 24

8.2.5. Time .................................................................................................................... 24

8.2.6. Apply Date/Time .................................................................................................. 24

8.3. Setting Recording Condition ....................................................................................... 25

8.3.1. Configuration Status ............................................................................................ 26

8.3.2. Channel Status .................................................................................................... 26

8.3.3. Recording Speed/Quality..................................................................................... 26

8.3.4. Speed(ips) ........................................................................................................... 26

8.3.5. Quality ................................................................................................................. 27

8.3.6. Audio Recording.................................................................................................. 27

8.3.7. Apply ................................................................................................................... 27

9. Connecting and Configuring Sensor ............................................................................. 28

9.1. Connecting Sensor Input ............................................................................................ 28

9.2. Setting Sensor at OSD menu ..................................................................................... 29

10. Connecting & Configuring Relay Out ......................................................................... 30

10.1. Connecting Relay Out ............................................................................................. 30

10.2. Configuring Relay Out............................................................................................. 31

11. Connecting External Device with Serial Port ............................................................. 32

11.1. Connecting Text Input Device (ATM / POS / Access Control) .................................. 32

12. Connecting & Configuring Serial Ports for Pan/Tilt/Zoom........................................ 33

12.1. Connecting Serial Port ............................................................................................ 33

12.1.1. Connecting RS232........................................................................................... 33

12.1.2. Connecting RS485........................................................................................... 33

12.1.3. Connecting RS422........................................................................................... 33

12.2. Configuring Serial Port ............................................................................................ 34

13. Connecting USB Device .............................................................................................. 35

14. Connecting External Storage ...................................................................................... 37

14.1. IEEE1394 Bay......................................................................................................... 37

14.2. Connecting IEEE1394 Device................................................................................. 37

HVR-04E TABLE OF CONTENTS

14.3. Available HDD......................................................................................................... 37

14.4. Registering & Formatting HDD................................................................................ 38

15. Network Monitoring & Managing ................................................................................ 39

15.1. Connecting Ethernet ............................................................................................... 39

15.2. Configuring HVR-04E’s Network Information .......................................................... 40

16. Using DVR Manager..................................................................................................... 41

16.1. PC System Requirements for running DVR Manager ............................................. 41

16.1.1. Installing DVR Manager ................................................................................... 41

16.1.2. Uninstalling DVR Manager............................................................................... 43

16.2. Configstation ........................................................................................................... 43

16.3. Monitor.................................................................................................................... 44

16.4. Playback ................................................................................................................. 44

APPENDIX ............................................................................................................................. 45

Appendix #1 Installing and Replacing internal HDD ......................................................... 46

Appendix #2 Video Input ..................................................................................................... 51

Appendix #3 Using CD-ROM ............................................................................................... 52

Appendix #4 Specification .................................................................................................. 53

6 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

OVERVIEW

1. What is HVR-04E?

The HVR-04E is a 4-Analog, 12-IP channel network digital video recorder. The HVR-04E can record and display 4 analog video channels and 12 IP video channels simultaneously. Video, Audio, and Text Event-

Logs are digitized and stored on two internal hard-drives.

Key features

□ Expandable up to 16 channels (4 analog video channels + 12 IP video channels)

□ 1 channel audio recording & playback

□ Total 120 ips recording speed (Analogue video 60ips + IP video 60ips)

□ Total 120 ips display speed (Max 60ips over Network)

□ Built-in software multiplexer for all 16 live monitoring channels (1 / 4 / 9 / 13 / 16Ch Mode on

CCTV Monitor as well as PC)

□ Maximum 4TB storage capacity (IEEE 1394 for external HDD)

□ ATM/POS transaction information text recording and search with corresponding video

□ 4 pairs of sensor inputs and alarm outputs

□ Built-in hardware motion detection with search function (64-division comparison)

□ Various efficient back-up methods (IEEE 1394(FiWi), USB (V 1.1), Ethernet)

□ PTZ Control (Preset support) via RS 232 and RS 485/RS422

□ User-friendly 32bit True-colored Graphic OSD Menu

□ Dynamic IP (DHCP, Floating IP) support (when xDSL and Cable Modem are used)

□ IR remote controller (User controls PTZ with remote controller)

□ Remote Management Software (DVR Manager)

HVR-04E

2. Supplied Accessories

Unpack and check all the items as below.

1. HVR-04E (1) 2. DC Power Supply (1)

(110V~220V)

OVERVIEW

3. AC Power Cord (1) 4. CD-ROM (Including DVR Manager) (1)

5. Remote Controller (1) 6. Guide (2)

7. Plug Bracket (1)

8

8. HDD Fixing Screw (8)

2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

3. Description & Function

HVR-04E Front

(1) LED

(2) IEEE1394 connecter

(3) Remote controller receiver

(4) USB connecter

(5) Function buttons

(6) Bracket fixing hole for rack mount

HVR-04E

HVR-04E Rear

OVERVIEW

(7) Power switch

(8) Ethernet connector

(9) BNC connector for Video input

(10) Audio input / output connector

(11) RS232 connecter (9Pin D-Sub)

(12) Terminal block for RS232 & 422/485

(13) Terminal block for Sensor input

(14) Terminal block for Relay output

(15) Video output for MONITOR or VCR

(16) Video input type/impedance select & remote controller switch

(17) IEEE1394 connecter

(18) USB connecter

(19) Power connector (DC12V)

(20) GND

10 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION HVR-04E

INSTALLATION AND CONNECTION

4. Connecting & Running HVR-04E

4.1. Connecting camera

(1) Connect CCTV camera to HVR-04E with BNC cable as shown below.

(2) Set video type (NTSC/PAL) by rear panel’s switch.

<Note>

The video type for all channels should be either NTSC or PAL. NTSC is the standard used in North

America.

(3) Set the impedance control switch for each channel as needed.

<Note>

It may be necessary to configure impedance of video input differently for each channel. For more detailed information, please refer to “Video type / impedance setup switch” in Appendix #2.

HVR-04E INSTALLATION AND CONNECTION

4.2. Connecting Monitor

(1) Connect CCTV monitor to HVR-04E with BNC cable as shown below.

<Note>

HVR-04E has two video output ports ; for Monitor and VCR. The output signals from the two ports are same and either port may be used.

4.3. Connecting Audio

(1) Connect audio signal to HVR-04E.

12 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION HVR-04E

HVR-04E INSTALLATION AND CONNECTION

4.4. Supplying Power

(1) Connect power cable to HVR-04E.

(2) Turn on the power switch located on the HVR-04E rear panel.

14

<Note>

Use the plug bracket to secure the power cable if needed.

<Note>

To connect EARTH, refer to the following picture.

2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION

5. Running OSD menu

5.1. Using menu

Press the [MENU] button to open the OSD Configuration Menu.

(1) Main Menu

(2) Sub-menu

(3) Setting Page

HVR-04E

(4) Help message

(1) Main Menu Tabs: The selected tab is shown in blue and the related sub-menus will be shown below the tab. To move to the previous/next Main Menu Tab, use the [◄◄ / ►►] arrow buttons. To move to a sub-menu, press the [ENTER] or [▼] buttons.

(2) Sub-menu: The selected sub-menu is shown in blue and the related setting page will be shown to the right of the sub-menu. Use the [▲/▼] arrow buttons to move within the sub-menu list. To move to the setting page press the [ENTER] button. To exit the setting page, press the [EXIT] button.

(3) Setting Page: The selected item is shown in gray. To move within each page, use the [◄◄ / ►►] or

[▲/▼] arrow buttons. Press the [ENTER] button to change the value of a setting. When the setting value is a word, a dialogue box to edit the word will open. When setting value is a number, it should be set with using the [◄◄ / ►►] or [▲/▼] arrow buttons. After the value is set, press the [EXIT] button. To exit the Setting Page, press the [EXIT] button.

(4) Help message: Related information for each menu/setting will be displayed here.

HVR-04E

5.2. Dialogue Box to Edit a Word

There are two methods to set word.

INSTALLATION AND CONNECTION

(1) Using number button

Enter the related numbers in order of horizontal/vertical. (For example, in order to select “C”, press [3] and [2] buttons.)

(2) Using arrow button

Select a value using the [◄◄ / ►►] or [▲/▼] buttons. The intersection of the horizontal and vertical bar is selected value. Press the [►] button to confirm the selected value.

(3) Function word

The following symbols are for executing specific functions:

9 : Enter

: Back Space & delete

: Space

◄ : Move to left

► : Move to right

: Previous Code Page

: Next Code Page

16 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION

6. Setting remote controller

6.1. Setting remote control DIP switch

Set the remote control DIP switch to “ON.”

HVR-04E

6.2. Set ID of HVR-04E

When controlling several HVR-04Es with one remote controller, set Remote Control ID as follows.

(1) Press [MENU] button.

(2) Select “System” with using [►►] button and press the [ENETR] or [▼] button.

HVR-04E INSTALLATION AND CONNECTION

(3) Select “Miscellaneous” from the sub-menu list using the [▼] button and press the [ENETR] button.

(4) Select “Remote Control ID,” and press the [ENETR] button.

(5) Select a value using the [◄◄ / ►►] buttons and press the [EXIT] button.

(6) Press the [EXIT] button to exit the Settings Page and return to Monitor mode.

<Note> Remote Control ID

Up to 16 HVR-04Es can be controlled with a single remote controller.

6.3. Selecting HVR-04E

If several HVR-04Es are set with unique ID numbers, they can be controlled with one remote controller.

To select a specific HVR-04E, press the ID button of remote controller until the 8 LEDs on the front of the HVR-04E light up and a buzzer sounds.

<Note>

Because remote controller ID is sixteen, HVR-04E will correspond.

18 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION

6.4. Operable range of remote controller

HVR-04E

6.5. Loading the batteries into remote controller

Remote controller requires two AAA-type batteries.

1. Remove the battery cover.

2. Taking care that the poles(+/-) are correctly positioned

3. Replace the battery cover.

<Note>

Batteries are not included as a packing accessory.

HVR-04E

7. HVR-04E Configuration

7.1. Basic Configuration

INSTALLATION AND CONNECTION

7.2. Advanced Configuration

20 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION

7.3. External Storage & Backup Configuration

HVR-04E

7.4. Internet/Intranet Configuration

HVR-04E INSTALLATION AND CONNECTION

8. HVR-04E Basic Setting

8.1. Viewing Image

After initial start-up, images from Ch.1~4 are displayed in a quad-split screen.

<Note>

If user password is set, a prompt for entering the password will appear.

22 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION

8.2. Setting Date & Time

HVR-04E

(1) Press [MENU] button, and select “Quick Setup” tab.

(2) Select “Date/Time” and enter the Settings Page by pressing [ENTER].

8.2.1. Time Zone

(1) Select “Time Zone” and press [ENETR] button to configure.

(2) Select a value using the [◄◄ / ►►] button and press the [EXIT] button when finished.

8.2.2. Daylight Saving

(1) “Daylight Saving Time” is only activated for time zones that use Daylight Savings. If activated, press

[ENTER] to enter a new value.

(2) Select “On/Off” using the [◄◄ / ►►] button and press the [EXIT] button when finished.

HVR-04E INSTALLATION AND CONNECTION

8.2.3. Time Format

(1) Select “Time Format” using the [◄◄ / ►►] or the [▲/▼] buttons and press [ENTER].

(2) Two Time Formats are available; ‘MM/DD/YYYY’ and ‘YYYY/MM/DD’. Select a value using [▲/

▼ ] buttons, and press the [EXIT] button when finished. (Default value is ‘MM/DD/YYYY’.)

8.2.4. Date

(1) Select “Date” using the [◄◄ / ►►] or the [▲/▼] buttons and press [ENTER].

(2) Select ‘MM’/‘DD’/‘YYYY’ using the [◄◄ / ►►] buttons, and select the value using the [▲/▼] buttons.

(3) Press the [EXIT] button when finished.

8.2.5. Time

(1) Select “Time” using the [◄◄ / ►►] or the [▲/▼] buttons and press [ENTER].

(2) Select ‘HH’/‘MM’ using the [◄◄ / ►►] buttons, and select the value using the [▲/▼] buttons.

(3) Press the [EXIT] button when finished.

8.2.6. Apply Date/Time

Most setting values are applied automatically, when exiting from the related menu page. But “Date”

& “Time” settings are not applied automatically because they may critically affect the file system of the recorded HDD. To apply Date/Time settings confirm settings with [Apply Date/Time] button.

(1) Select “Apply Date/time” using the [◄◄ / ►►] or the [▲/▼] buttons and press [ENTER]. A warning message will appear.

(2) Select “OK” using the [◄◄ / ►►] or the [▲/▼] buttons and press [ENTER]. To cancel, press the

[EXIT] button.

24 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION HVR-04E

8.3. Setting Recording Condition

Recording conditions under the “Quick Setup” menu tab apply the same values to all analog channels 1~4.

All settings are applied for 24 hours/day regardless of the values set for “Time Schedule” or “Alarm Rec.”

HVR-04E INSTALLATION AND CONNECTION

(1) Press [MENU] button, and select “Quick Setup.”

(2) Move to sub-menu by pressing [ENTER] or the [▼] button.

(3) Select “Recording” using the [▲/▼] buttons and press the [ENTER] button.

8.3.1. Configuration Status

Displays the recording configuration status. When setting up through the “Quick Setup” menu, “Quick

Setup” will be shown. When setting up through “Normal Rec.” or “Alarm Rec.,” “Custom Setup” will be shown.

<Note>

Only when all the 16 channels' normal recording conditions are set through 'Macro Setup' and maintained, it is marked as 'Macro Setup'. Otherwise, it will be marked as 'Custom Setup'.

8.3.2. Channel Status

(1) Select “Channel Status” using [▲/▼] buttons and press the [ENTER] button.

(2) Select a value using the [◄◄ / ►►] button. Press the [EXIT] button when finished.

8.3.3. Recording Speed/Quality

(1) Select “Recording Speed/Quality” using [▲/▼] buttons and press the [ENTER] button.

(2) Select a value using the [◄◄ / ►►] button. Press the [EXIT] button when finished.

<Note> Recording Speed/Quality means

- Low : Speed=1ips and Quality=Q5

- Std. : Speed=5ips and Quality=Q5

- High : Speed=15ips and Quality=Q5

- Custom : Manually defined by User.

8.3.4. Speed(ips)

When “Recording Speed/Quality” is set as “Custom,” values can be set manually.

(1) Select “Speed” using [▲/▼] buttons and press the [ENTER] button.

(2) Select a value using the [◄◄ / ►►] button. Press the [EXIT] button when finished.

26 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION

8.3.5. Quality

When “Recording Speed/Quality” is set as “Custom,” values can be set manually.

(1) Select “Quality” using [▲/▼] buttons and press the [ENTER] button.

(2) Select a value using the [◄◄ / ►►] button. Press the [EXIT] button when finished.

8.3.6. Audio Recording

(1) Select “Audio Recording” using [▲/▼] buttons and press the [ENTER] button.

(2) Select a value using the [◄◄ / ►►] button. Press the [EXIT] button when finished.

8.3.7. Apply

(1) Select “Apply” using [▲/▼] buttons and press the [ENTER] button.

(2) Setting values are applied and the previous menu will be displayed.

HVR-04E

HVR-04E INSTALLATION AND CONNECTION

9. Connecting and Configuring Sensor

9.1. Connecting Sensor Input

To connect a sensor to S1, fix the wire to “S1” and “G“.

<Note>

Devices connected to the sensor input should have “Dry contact.” The following diagram is of an electric circuit with approximately 12mA flows.

28 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION

9.2. Setting Sensor at OSD menu

HVR-04E

After a sensor is connected, it can be activated through the OSD Configuration menu.

Select the sensor number (S1, S2, etc.) and press the [Enter] button to configure. Use the [◄◄ / ►►] buttons to select “On” or “Off.” Press [EXIT] when finished.

<NOTE>

When activated, the “Pre / Post Alarm” function will cause the HVR-04E to record images at the specified Speed and Quality for a length of time before and/or after the sensor is triggered.

HVR-04E INSTALLATION AND CONNECTION

10. Connecting & Configuring Relay Out

10.1. Connecting Relay Out

HVR-04E has total four ports of Relay Out.

To connect a device to “O1,” connect the wires to two “O1”s.

<Note>

The rated voltage and current of Relay Out are as follows. Do not exceed the rated values.

Maximum Switching Capacity

24V DC, 1.25A, 30W

125V DC, 0.24A, 30W

125V AC, 0.5A, 62.5VA

30 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION

10.2. Configuring Relay Out

HVR-04E

Each relay can be synchronized with a sensor input or with motion detection for each of the four time schedules (Weekday (Day), Weekday (Night), Weekend (Day), Weekend (Night)). Relays can also be controlled locally by pressing the [SEARCH/RELAY] button followed by the relay number (1-4). Relays can also be controlled remotely through the “DVR Manager Software.”

HVR-04E INSTALLATION AND CONNECTION

11. Connecting External Device with Serial Port

11.1. Connecting Text Input Device (ATM / POS / Access Control)

In addition to images, the HVR-04E can record text data received from POS/ATM through the RS232 serial port.

Connect RS232 to 9pin D-sub of HVR-04E, and configure the “Text” sub-menu under the “System” tab.

Set “Serial Setup” under the “System” menu tab to “RS232” and “Device” to “Text.” The baud rate may differ for each device; consult the device manual for more information.

<Note>

Before installing any external device, consult with the local HUNT ELECTRONIC USA, INC. distributor. Some external devices may not be compatible with the HVR-04E.

32 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION HVR-04E

12. Connecting & Configuring Serial Ports for Pan/Tilt/Zoom

12.1. Connecting Serial Port

The HVR-04E has most major PTZ protocols already pre-programmed. Makes and models not supported can still be controlled using the Transparent Protocol. For a list of supported protocols, refer to the list on the OSD Configuration menu.

12.1.1. Connecting RS232

Fix the wire to 1~3 pins (RX, TX, GND).

12.1.2. Connecting RS485

Fix the wire to 4~5 pins and 8 pin (R+, R-,GND).

12.1.3. Connecting RS422

Fix the wire to 4~8 pins (R+, R-, T+, T-, GND).

HVR-04E INSTALLATION AND CONNECTION

12.2. Configuring Serial Port

Configure PTZ serial ports and available modes at “System / Serial Setup”.

After completing serial setup, configure base address and port for each channel under the “Camera” menu tab. When connecting PTZ devices to several cameras, be sure the base address matches the address for the camera.

34 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION HVR-04E

<Note> Wire Handling

Trimming Wire

When connecting a wire to a terminal block, follow the instructions below. Note the different types of wire that can be used.

Stranded Wire: Peel off the wiring cover

8~10mm and solder it. Wire gage should be

AWG 22 ~ 26.

Solid Wire: Peel off the wiring cover 8~10mm and solder it. Wire gage should be AWG 20 ~

26.

Inserting & removing wire

To insert the wire, use a screwdriver as shown in the diagram to the right.

13. Connecting USB Device

USB port can be used to copy up to 1 minute of images to a USB Flash memory disk. When connecting

USB device, do not exceed the rated values of USB device.

USB Spec.

Available Device

Ver 1.1 (Max 12M bps)

USB Memory Stick,

Output Voltage/Current Max. 200mA per DC 5V / Port

<Note>

The disk should be formatted with FAT32 type.

HVR-04E INSTALLATION AND CONNECTION

If properly connected, the disk is recognized automatically as in the following picture. To copy images, the process is as follows: Set copy range (up to 1 minute) Æ Select drive Æ Copy (press “Start”).

<Note>

USB Flash products that require a Windows program to operate may not be recognized by the HVR-

04E.

36 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION HVR-04E

14. Connecting External Storage

14.1. IEEE1394 Bay

HVR-04E has three IEEE1394 ports for external storage device interface. With them, HVR-04E can expand storage capacity up to 4TB.

<Note>

Some IEEE1394 Bay may not be recognized by the HVR-04E. Before purchasing, consult the local

HUNT ELECTRONIC USA, INC. distributor.

14.2. Connecting IEEE1394 Device

When using FireWire supported external HDD, hard drive bays can be connected to 1 port in the front panel or 2 ports in the rear panel. The HVR-04E does not supply power to the hard drive bay; therefore only bays that use external power can be used.

14.3. Available HDD

It is recommended to use the following HDD models with the HVR-04E. If a non-recommended HDD is used, Hunt Electronic USA, Inc. will not guarantee the warranty.

Manufacturer : MAXTOR

Series Model No. Size

DiamondMax

Plus 9

(7200rpm)

6Y060L0 60GB

6Y080L(P)0 80GB

DiamondMax

6Y120L(P)0 120GB

16

6Y160L(P)0 160GB

(5400rpm)

6Y200P0 200GB

6Y250P0 250GB

4R060L0 60GB

4R080L0 80GB

4R120L0 120GB

4R160L0 160GB

<Note>

Buffer for DiamondMax Plus 9’s model “L” is 3MB; for model “P” the buffer is 8MB.

HVR-04E INSTALLATION AND CONNECTION

14.4. Registering & Formatting HDD

“Disk Manager” will automatically run on start-up after installing a HDD.

If “Disk Manager” does not automatically run on start-up, make sure the HDD is properly installed.

(1) Press [ENTER] button at “Select Disk”.

(2) Select new added HDD (indicated as “[F]”) using [▲/▼] button and press [EXIT] button

(3) Select “Action” using [▲/▼] button and press [EXIT] button.

(4) Select “Add” using [◄◄ / ►►] button and press [EXIT] button.

(5) Select “Apply” using [▲/▼] button and press [EXIT] button. The HDD status is changed to “[*]”.

(6) Select “Action” using [▲/▼] button and press [EXIT] button.

(7) Select “Format” using [◄◄ / ►►] button and press [EXIT] button.

38 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION HVR-04E

(8) Select “Apply” using [▲/▼] button and press [EXIT] button. The HDD status is changed to “[R]” after formatting.

(9) Shut down “Disk Manager” by pressing [EXIT] button.

15. Network Monitoring & Managing

HVR-04E can be accessed, controlled, and managed from remote site via Internet/Intranet.

15.1. Connecting Ethernet

1) Turn off HVR-04E’s power switch.

2) Connect HVR-04E to hub with Ethernet cable.

3) Turn on HVR-04E’s power switch.

<Note>

1. Supply power to HVR-04E after connecting Ethernet cable to protect against electrical damage to

HVR-04E.

2. Check cable connection status.

3. Check LED on HVR-04E’s rear panel after supplying power.

HVR-04E INSTALLATION AND CONNECTION

15.2. Configuring HVR-04E’s Network Information

The following description is on based on Ethernet connection. For more detailed information on the

Network Settings Page, please refer to “HVR-04E OSD User’s Guide”.

(1) Press [MENU] button.

(2) Select “System” using the [◄◄ / ►►] buttons and press [ENTER].

(3) Select “Network” using the [▲/▼] buttons and press [ENTER].

(4) Select “IP Addr” using the [▲/▼] buttons and press [ENTER].

(5) Press [EXIT] button after entering IP address in the dialogue box.

(6) Select “Net Mask” using the [▲/▼] buttons and press [ENTER].

(7) Press [EXIT] button after entering Net Mask in the dialogue box.

(8) Select “Gateway” using the [▲/▼] buttons and press [ENTER].

(9) Press [EXIT] button after entering Gateway in the dialogue box.

(10) Select “DNS” using the [▲/▼] buttons and press [ENTER].

(11) Press [EXIT] button after entering DNS in the dialogue box.

(12) Press [EXIT] button to exit the page.

40 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION HVR-04E

16. Using DVR Manager

16.1. PC System Requirements for running DVR Manager

Minimal Requirements Recommended Requirements

CPU

RAM

VGA

OS

Resolution

Network

P-Ⅲ 600MHz or above

128 MB or above

16 MB or above

Windows 2000/XP

1024 X 768 pixels or above

100 Base TX Fast Ethernet

P-Ⅲ 1GHz or above

256 MB or above

32 MB or above

Windows 2000/XP

1024 X 768 pixels or above

100 Base TX Fast Ethernet

16.1.1. Installing DVR Manager

(1) Insert Setup CD-ROM into CD-ROM drive of administrator’s PC

(2) Doubleclick the DVR Manager setup file. Install Shield Wizard will be automatically installed.

(3) Click the “I Agree” button to accept the license agreement

HVR-04E INSTALLATION AND CONNECTION

(4) Select which components to install and press the “Next” button.

(5) Browse and choose a directory if the default directory is not preferred. Click the “Install” button, after selecting a directory to install.

(6) Click the “Close” button after DVR Manager program is installed successfully

42 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

INSTALLATION AND CONNECTION

16.1.2. Uninstalling DVR Manager

(1) Click Windows “Start” Button.

(2) Select and Click ‘Uninstall’ icon to run Uninstall Shield.

HVR-04E

(3) DVR Manager program will be automatically deleted.

16.2. Configstation

Click icon on desktop to run “DVR Manager Configstation” program.

HVR-04E INSTALLATION AND CONNECTION

16.3. Monitor

Click the related icon and run the “DVR Manager Monitor” program.

16.4. Playback

Click the related icon and run the “DVR Manager Playback” program.

44 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

APPENDIX

APPENDIX

HVR-04E APPENDIX

Appendix #1 Installing and Replacing internal HDD

Compatible HDD

It is recommended to use the following HDD models with the HVR-04E. If a non-recommended HDD is used, Hunt Electronic USA, Inc. will not guarantee the warranty.

Manufacturer : MAXTOR

Series Model No. Size

6Y060L0 60GB 4R060L0 60GB

4R080L0 80GB

DiamondMax

Plus 9

(7200rpm)

6Y080L(P)0 80GB

DiamondMax

6Y120L(P)0 120GB

16

6Y160L(P)0 160GB

(5400rpm)

6Y200P0 200GB

4R120L0 120GB

4R160L0 160GB

6Y250P0 250GB

<Note>

L series of DiamondMax Plus 9 has 3MB buffer memory, while P model has 8MB

Installing & Replacing

Adding or replacing HDD should follow below process

(1) Turn off the power of HVR-04E.

(2) Check whether the dip switches are set as illustrated below

46 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

<Note>

The dip switch should be set at ‘MASTER’ position for the first installed or built-in HDD.

Additional HDD should be set as ‘SLAVE.’ Identical dip switch setting may cause system conflict

or mal-function.

(3) Remove the 6 screws as illustrated below and pull up the cover from the rear part to open

(4) Take out power and data cable of HDD from Main PCB ASS’Y. Remove 4 HDD Bracket screws and take out HDD ASS’Y.

HVR-04E

(5) Fix the HDD with provided screws. Connect power and data cables to HDD

APPENDIX

Installing single HDD Installing 2 HDDs

<Note> Caution for HDD Management

1. Replacing ‘SLAVE’ HDD of internal 2 HDDs causes permanent data loss in the SLAVE HDD.

2. MASTER HDD has all the index of stored data including ‘SLAVE’ HDD. Corruption on ‘MASTER’

HDD may cause total data loss. Be careful when handling the main HDD.

3. It is strongly recommended that MASTER HDD should be backed up before replacing

(6) Connect HDD power cable to main PCB ASS’Y. Secure the HDD with screws.

(7) Connect HDD cable’s connector to HDD as in the following picture.

48 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

(8) Assemble the top cover.

Registering & Formatting HDD

“Disk Manager” will automatically run on start-up after installing a HDD. If “Disk Manager” does not automatically run on start-up, make sure the HDD is properly installed.

(9) Press [ENTER] button at “Select Disk”.

(10) Select new added HDD (indicated as “[F]”) using [▲/▼] button and press [EXIT] button

HVR-04E APPENDIX

(11) Select “Action” using [▲/▼] button and press [EXIT] button.

(12) Select “Add” using [◄◄ / ►►] button and press [EXIT] button.

(13) Select “Apply” using [▲/▼] button and press [EXIT] button. The HDD status is changed to “[*]”.

(14) Select “Action” using [▲/▼] button and press [EXIT] button.

(15) Select “Format” using [◄◄ / ►►] button and press [EXIT] button.

(16) Select “Apply” using [▲/▼] button and press [EXIT] button. The HDD status is changed to “[R]” after formatting.

(17) Shut down “Disk Manager” by pressing [EXIT] button.

<Note> HDD Type at Disk Manager

1. [R] Available of recording

2. [V] Connected and formatted as HVR-04E’s file system

If using ‘Add used’ command, it will be changed to [R]. There is no need to reformat.

3. [F] Connected but not available file system. After using ‘Add’, need to format for making as [R].

4. [*] Connected and added using the ‘ADD’ command. If formatting, it will be [R].

5. [X] HDD cable is not

<Note> HDD Managing Command

1. Format : Format as HVR-04E’s file system. Not available to PC file system.

2. Add : Add HDD for recording. Need to format.

3. Add Used : Add a HDD that has been used and formatted. There is no need to reformat

4. Remove : Remove current HDD. HDD can be reused without data loss by the ‘Add Used’ command.

5. Confirm Removed : U sed when a removed HDD is still listed. ALL DATA WILL BE LOST!

<Note> How to format current HDD?

HVR-04E doesn’t need additional format command. Just do it; ‘Remove’ Æ ‘Add’ Æ ‘Format’.

50 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

Appendix #2 Video Input

Video type / impedance setup switch

It’s possible to set up Impedance of Video input line.

When one Video output is connected to several Input as below, the impedance of one input should be 75 ohm.

HVR-04E APPENDIX

Appendix #3 Using CD-ROM

Components of CD- ROM disc

Installation Guide : HVR-04E Installation Guide

User’s Guide

DVR Manager

Acrobat Reader

: HVR-04E User’s Guide

: DVR Manager User’s Guide

( HVR-04E Remote Management Program)

: Version 5.1

Preparation

To read manual of CD-ROM disc, Adobe Acrobat 5.0 should be installed in client’s PC.

<Note>

If Adobe Acrobat Reader is not installed within client’s PC, use the Acrobat Reader program of CD-

ROM.

Reading manual of CD-ROM

Follow the steps to read user’s guide.

1. Insert the supplied CD-ROM into CD-ROM drive of PC.

2. Open the user’s guide, PDF file.

52 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

Appendix #4 Specification

General

CPU 32bit RISC Processor (200MIPS)

Flash Memory

Main Memory

8MB

64MB

OS

Video Channel

Storage Device

Embedded LINUX

4 Analog Channel & 12 IP Video Channel (NTSC or PAL)

Internal 3.5” IDE HDD 2EA (default 1EA)

External 3EA for IEEE1394 Interface

Support Max. 4Tbytes

Data-loss protection against power failure Intelligent File System

Image Compression

Technology

Average File Size

Image Quality Level

Image Compression Rate

Recording Speed

Differential Wavelet

1~5KB (Standard Quality)

5 Level

20:1~500:1

Max. 120ips in total at NTSC (Analog Ch 60ips + IP Video Ch

60ips)

Network

Browser

Protocol

Connector

S/W Upgrade

Simultaneous Users

Security

DVR Manager

TCP/IP, ARP, ICMP, DHCP, PPPoE

10/100Mbps Ethernet (RJ-45)

Firmware upgrade via Network

Monitoring : Max. 5 Users

Playback : Max. 5 Users

Password (User or Administrator Authentication)

Watermarking (Against image forging)

HVR-04E

Display

Monitoring

Viewer

Playback Performance

Playback Speed

Function

Max. 120ips (Analog Video 60ips)

(IP Video 60ips)

1ch, 4ch, 9ch, 13ch, 16ch, Auto Sequential

Max. 60ips

1x, 2x, 4x, 8x, 16x (Forward & Reverse Play)

Step-Forward, Step-Reverse

Environment

Operation Temperature

Storage Temperature

Analogue VCR

Backup Reminder

Data Copy

Input/Output

Video

5~45 Cº

-10~55 Cº

Operation Humidity

Storage Humidity

30~80%, free of condensation

93% below, free of condensation

Data Backup/Expansion/Copy

HDD Expandable Data Backup IEEE1394

VHS Video output for VCR

Daily / Weekly / Monthly

USB Flash memory disk

Audio

Digital Output

Digital Output Schedule

Sensor Input

1 Monitor output via BNC

1 Video output via BNC

1 Input : Line-in, 1 Vpp

1 Output : Line-out, 1Vpp

Level : -7~8(16 Step) Recording level

AMP : 20dB amplifier for low level audio

Monitoring : Local and remote

4 Relay outputs (Max DC 30W, AC 62.5VA)

Daily : Day / Night

Weekly : Weekdays / Weekends

Conditions : MD, Sensor inputs

4 Sensor inputs (Support Dry contact)

APPENDIX

54 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

PTZ Control

Serial Port

Control Method (Local)

Control Method (Remote)

Preset Mode

Group Mode

Others

Digital Zoom

Alarm Trigger

Alarm Data Preservation

Alarm Log

Pre/Post Alarm

Schedule Recording

Text Data Recording

Electricity

Power (Applied Adaptor)

Consumption Current

Consumption Voltage

RS232(1), RS485(1), RS422(1)

Front panel button & IR remote controller

(control IP video channel as well)

On-the-screen PTZ control on PC

8 points preset per channel

1 group per channel

2x (Live & PlayBack Mode)

Motion Detection or Sensor input

Alarm triggered Video Data Preservation

Log search

Log monitoring via OSD & Network

Pre : 1~10 seconds

Post : 1~60 seconds

Daily : Day / Night

Weekly : Weekdays / Weekends

Conditions : Normal / Event

POS/ATM transaction information archived along with corresponding video data

DC 12V

Max 4.5A (Internal 2 HDD)

Typical 2.9A (Internal 2 HDD)

Max. 54W

Typical 35W

HVR-04E

Mechanical

Dimension (WDH)

Weight

306ⅹ280ⅹ67(mm)

3.5Kg (With one HDD)

APPENDIX

56 2003.05.21 (v 1.0) Hunt Electronic USA, Inc.

Hunt Electronic USA, Inc.

978 West 10 th Street

Azusa, California 91702

Tel : (626) 812-8868

Fax : (626) 812-8828

Technical Support: 1-888-993-4868

URL: www.huntcctv.com

E-mail: [email protected]

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement