DVD Player
DVD-P182
DVD-P183
www.samsung.com
AK68-01505A(01)
PRECAUTIONS
1. Setting up
- Refer to the identification label located on
the rear of your player for its proper operating voltage.
- Install your player in a cabinet with adequate ventilation holes. (7~10cm) Do not
block ventilation holes on any of the components for air circulation.
- Do not push the disc tray in by hand.
- Do not stack components.
- Be sure to turn all components off before
moving the player.
- Before connecting other components to this
player, be sure to turn them off.
- Be sure to remove the disc and turn off the
player after use, especially if you don’t use
it for a long time.
- The mains plug is as a disconnect device
and shall stay readily operable at any time.
2. For your safety
- This product utilizes a laser. Use of controls
or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
- Do not open covers and do not repair yourself. Refer servicing to qualified personal.
3. Caution
- Your player is not intended for industrial use
but for domestic purposes. Use of this product is for personal use only.
- Apparatus shall not be exposed to dripping
or splashing and no objects filled with liquids, such as vases, shall be placed on the
apparatus.
- Exterior influences such as lightning and
static electricity can affect normal operation
of this player. If this occurs, turn the player
off and on again with the POWER button, or
disconnect and then reconnect the AC
power cord to the AC power outlet. The
player will operate normally.
- When condensation forms inside the player
2
due to sharp changes in temperature, the
player may not operate
correctly. If this occurs, leave the player at
room temperature until the inside of the
player becomes dry and operational.
4. Disc
- Do not clean record-cleaning sprays, benzene, thinner, or other volatile solvents that
may cause damage to the disc surface.
- Do not touch the disc’s signal surface. Hold
by the edges or by one edge and the hole
in the center.
- Wipe the dirt away gently; never wipe a
cloth back and forth over the disc.
5. Environmental info
- The battery used in this product contains
chemicals that are harmful to the environ
ment.
- So, dispose of batteries in the proper man
ner, according to federal, state, and local
regulations.
The product unit accompanying this user manual is
licensed under certain intellectual property rights of
certain third parties. This license is limited to private
non-commercial use by end-user consumers for
licensed contents. No rights are granted for
commercial use. The license does not cover any
product unit other than this product unit and the
license does not extend to any unlicensed product
unit or process conforming to ISO/OUR 11172-3 or
ISO/OUR 13818-3 used or sold in combination with
this product unit. The license only covers the use of
this product unit to encode and/or decode audio files
conforming to the ISO/OUR 11172-3 or ISO/OUR
13818-3. No rights are granted under this license for
product features or functions that do not conform to
the ISO/OUR 11172-3 or ISO/OUR 13818-3.
CAUTION: USE OF ANY CONTROLS,
ADJUSTMENTS, OR PROCEDURES OTHER
THAN SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DVD
TV
TV SOURCE
STEP
ZOOM
VIDEO SEL. SUBTITLE
+
TV VOL
^
PLAY
STOP
TV CH
^
MENU
RETURN
ENTER
DISC MENU EZ VIEW
INFO
OPEN/CLOSE AUDIO
REPEAT
CANCEL
REPEAT
A-B
BEFORE YOU
Remote Control
BEFORE
YOU
Batteries for Remote
STAR T
Control (AAA Size)
STAR T
SELECT
POWER
SAMSUNG
DVD
TV
SELECT
POWER
SAMSUNG
DVD
TV SOURCE
TV
STEP
ZOOM
VIDEO SEL. SUBTITLE
TV VOL
PLAY
STOP
-
^
TV CH
TV SOURCE
RETURN
STEP
MENU
ZOOM
VIDEO SEL. SUBTITLE
+
TV VOL
PLAY
STOP
^
+
^
TV CH
ENTER
^
MENU
RETURN
DISC MENU EZ VIEW
INFO
OPEN/CLOSE AUDIO
REPEAT
ENTER
DISC MENU EZ VIEW
INFO
OPEN/CLOSE AUDIO
REPEAT
CANCEL
REPEAT
A-B
CANCEL
REPEAT
A-B
Remote Control
User’s
Manual
Remote
Control
Batteries for Remote
Video/Audio
Batteries
for Remote
Control (AAA
Size)
Cable
Control (AAA Size)
Install Batteries in the Remote control
1. Open the battery cover on the back of the remote
control.
2. Insert two AAA batteries.
Make sure that the
User’s Manual
Video/Audio
polarities
(+ and -) are aligned correctly.
User’s
Manual
Video/Audio
Cable
3. Replace the
battery cover.
Cable
Install Batteries in the Remote control
Install Batteries in the Remote control
1. Open the battery cover on the back of the remote
1. Open
the battery cover on the back of the remote
control.
If remote
control doesn’t operate
2. control.
Insert two AAA batteries.
properly:
2. Insert
Make two
sureAAA
thatbatteries.
the
- Check
the
- ofaligned
the batteries
(Dry-Cell)
Make
surepolarity
polarities
(+that
andthe
-)+ are
correctly.
- 3.
Check
if the
are
drained.
polarities
(+batteries
and
-) are
aligned
correctly.
Replace
the
battery
cover.
Replace
the battery
cover.
- 3.
Check
if remote
control
sensor is blocked by
obstacles.
- Check if there is any fluorescent lighting nearby.
If remote control doesn’t operate
If
remote control doesn’t operate
properly:
properly:
- Check the polarity + - of the batteries (Dry-Cell)
-- Check
polarity
+ - of
batteries (Dry-Cell)
Check the
if the
batteries
arethe
drained.
-- Check
batteries
aresensor
drained.
Check ifif the
remote
control
is blocked by
- Check
if remote control sensor is blocked by
obstacles.
- obstacles.
Check if there is any fluorescent lighting nearby.
- Check if there is any fluorescent lighting nearby.
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Setup
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Disc Type and Characteristics . . . . . . . . . . . . . . . . 5
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tour of the Remote Control . . . . . . . . . . . . . . . . . . 8
Connections
Choosing a Connection . . . . . . . . . . . . . . . . . . . . . 9
Basic Functions
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Playing
Disc
. . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Before ayou
start
Precautions.
. . . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 23
Using
the
Search
Before
you
start
.and
. . . Skip
. . . . Functions
. . . . . . . . ...................16
.3
Setup
Using
theFeatures
Display Function
Setup
General
. . . . . . . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .16
.4
Using
theFeatures
Disc
General
. Title
. . . . Menu
. . . . . ............................................16
.. 45
Disc Type
and and
Characteristics
Repeat
Playand
. .. .. .. .. .. .. .. .. .. .. .. ..............................................17
Disc
Type
.. 56
Description
.. .. .Characteristics
Slow
Play
.
.
.
.
.
Description
.
.
.
........Control
..............................................................17
.. 68
Tour of the Remote
Advanced
Functions
Tour
of the Remote
Control . . . . . . . . . . . . . . . . . . 8
Connections
Adjusting
Aspect Ratio. .(EZ
Connections
Choosingthe
a Connection
. . . View)
. . . . . .. .. .. .. .. .. .. .. .. .18
.9
Selecting
the
Audio
Language
.
Choosing
a Connection . . . . . .............................18
.9
Basic Functions
Selecting
the
Subtitle
Basic
Playing aFunctions
Disc
. . . . .Language.
. . . . . . . . .. .. .. .. .. .. .. .. .. .. .. .. .. .19
15
Changing
Camera
Playing
a the
Disc
. . .and
. . .Angle
. . . . Functions
..........................................19
15
Using the
Search
Skip
16
Using
Using
the
Search
and
Skip Functions
16
Usingthe
theInstant
DisplayReplay/Skip
Function
. .Function
. . . . . . ..........................19
16
Using
the
Bookmark
Function
.
Using
the
Display
Function
.
.
.
16
Using the Disc and Title Menu ..........................................20
16
Using
the
Zoom
Using
the
Disc. .and
16
Repeat
Play
.Function
. . Title
. . . . Menu
.. .. .. .. .. ...........................................20
17
Clips
Repeat
Play
SlowMenu
Play
.for
. .. .MP3/WMA/JPEG/
. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 17
17
CD
Audio/MPEG4.
Slow
Play . . . . Functions
. . .................................................21
17
Advanced
Folder
Selection
. . . . .Ratio
. . . . (EZ
. . . .View)
. . . . . .. .. .. .. .. .. .. .. .21
Advanced
Functions
Adjusting
the Aspect
18
MP3/WMA/CD
AudioLanguage
Playback.
Adjusting
Ratio (EZ ..View)
18
Selecting the
the Aspect
Audio
.. .. .. .. ............................21
18
MPEG4
Playback
. . Language
. . Language.
. . . . . . ...........................................22
Selecting
the
18
Selecting
the Audio
Subtitle
19
Picture
CD
Playback.
.
.
. . . . . .. .. ........................................23
Selecting
19
Changingthe
theSubtitle
CameraLanguage.
Angle
19
Changing
Setup
Menu
Changing
Camera
Angle
. Function
. . . . . . . .. .. .. .. .. .. .. .. 19
Using the the
Instant
Replay/Skip
19
Using
Menu
. . . . . . .Function
Using
the
Instant
Replay/Skip
19
Usingthe
theSetup
Bookmark
Function
.. .. .. .. .. .. .........................24
20
Setting
Up
the
Language
Features
Using
Function
20
Using the
the Bookmark
Zoom Function
. . . . .. .. .. ...................................24
20
Setting
Up Zoom
the
Options
Using
the
Function
. . .................................25
20
Clips Menu
forAudio
MP3/WMA/JPEG/
Setting
Up the
Clips
Menu
forDisplay
MP3/WMA/JPEG/
CD Audio/MPEG4.
. . .Options
. . . . . . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .27
21
Setting
Up
the Parental
CD
Audio/MPEG4.
.. .. .. .. .. ............................................28
21
Folder
Selection
. . .. .. .. ..Control
21
Reference
Folder
SelectionAudio
. . . . Playback.
. . . . . . . . .. .. .. .. .. .. .. .. .. .. .. .. .. .. 21
MP3/WMA/CD
21
Firmware
Upgrade
MP3/WMA/CD
Audio
21
MPEG4 Playback
.. .. ..Playback.
.. .. .. .. .. .. .. ...........................................30
22
Troubleshooting
.
.
.
.
.
MPEG4
Playback
.
.
.
.
22
Picture CD Playback. ................................................................31
23
Specifications
. .Setup
. . . . ......Menu
......................................32
Picture
CD Playback.
23
Changing
TABLE OF
TABLE OF
CONTENT
CONTENT
Changing
Setup
Using the Setup
Menu . Menu
. . . . . . . . . . . . . . . . . . . . 24
Using
Menu . . .Features
. . . . . . . .. .. .. .. .. .. .. .. .. .. .. 24
Settingthe
UpSetup
the Language
24
Setting
Features
Setting Up
Up the
the Language
Audio Options
. . . . . .. .. .. .. .. .. .. .. .. .. .. 24
25
Setting
Options
. . .. .. .. .. .. .. .. .. .. .. .. .. .. 3
.. 25
Setting Up
Up the
the Audio
Display
Options
27
Setting
Setting Up
Up the
the Display
ParentalOptions
Control .. .. .. .. .. .. .. .. .. .. .. .. .. .. 27
28
Setting
Up the Parental Control . . . . . . . . . . . . . . 28
Reference
Reference
Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . 30
Firmware
Upgrade
Troubleshooting
. . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 30
31
Troubleshooting
Specifications . . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 31
32
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3
3
English
SAMSUNG
English
English
SELECT
POWER
SETUP
General Features
SETUP
Excellent Sound
Dolby Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound reproduction.
General Features
Screen
Both regular and
widescreen(16:9) pictures can be
Excellent
Sound
viewed.
Dolby
Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound reproduction.
Slow Motion
An important scene can be viewed in slow motion.
Screen
Both
regular and
widescreen(16:9)
Parental
Control
(DVD) pictures can be
viewed.
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such
as those with violence, adult subject
Slow
Motion
matter,
etc.
An
important
scene can be viewed in slow motion.
Various On-Screen
Menu Functions
Parental
Control
(DVD)
You parental
can select
various
languages
(Audio/Subtitle)
The
control
allows
users to
set the level
and
screen
angles
while
enjoying
necessary to prohibit children frommovies.
viewing harmful
movies such as those with violence, adult subject
matter,
etc.
Progressive
Scan
Progressive scanning creates an improved picture
with double On-Screen
the scan lines ofMenu
a conventional
interVarious
Functions
lacedcan
picture.
You
select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
EZ VIEW (DVD)
Easy View enablesScan
picture adjustment to match
Progressive
your TV's screen
size creates
(16:9 or an
4:3).
Progressive
scanning
improved picture
with double the scan lines of a conventional interlaced
picture.
Digital
Photo Viewer (JPEG)
You can view Digital Photos on your TV.
EZ VIEW (DVD)
Easy
View enables picture adjustment to match
Repeat
your
TV'srepeat
screena size
or 4:3).
You can
song(16:9
or movie
simply by pressing
the REPEAT button.
Digital Photo Viewer (JPEG)
You
can view Digital Photos on your TV.
MP3/WMA
This unit can play discs created from MP3/WMA
files.
Repeat
You can repeat a song or movie simply by pressing
the
REPEAT
button. (DVD)
Instant
Replay
This function is used to replay the previous 10
seconds
of
a
MP3/WMAmovie from the current position.
This unit can play discs created from MP3/WMA
files.
Instant Skip (DVD)
This function skips playback ahead 10 seconds.
Instant Replay (DVD)
MPEG4
This
function is used to replay the previous 10
This unitofcan
play from
MPEG4
formats
within an
seconds
a movie
the current
position.
avi file.
Instant Skip (DVD)
This function skips playback ahead 10 seconds.
MPEG4
This unit can play MPEG4 formats within an
avi file.
4
4
Note
- Discs which cannot be played with this
player.
• DVD-ROM
• DVD-RAM
• CD-ROM
• CDV
Note
• CDI
• CVD
-• Discs
be played
with this
CDGswhich
play cannot
audio only,
not graphics.
player.
- Ability to play back may depend on recording
•conditions.
DVD-ROM
• DVD-RAM
• CD-ROM
• CDV
DVD-R, +R
• CDI
• CVD
CD-RW
• CDGs
play -RW
audio(Vonly,
not graphics.
DVD+RW,
mode)
- Ability
to may
play not
backplay
maycertain
depend
on recording
The unit
CD-R,
CD-RW
conditions.
and DVD-R due to the disc type or recording
conditions.
• DVD-R, +R
• CD-RW
COPY
PROTECTION
• DVD+RW, -RW (V mode)
Many DVD discs are encoded with copy protection.
- The unit
mayyou
not should
play certain
CD-R, CD-RW
Because
of this,
only connect
your DVD
anddirectly
DVD-Rtodue
thenot
disctotype
or recording
player
yourtoTV,
a VCR.
Connecting
to conditions.
a VCR results in a distorted picture from copyprotected DVD discs.
COPY
PROTECTION
This product
incorporates copyright protection
technology
that isare
protected
bywith
methods
claims of
Many
DVD
discs
encoded
copy protection.
certain
U.S.
patents
and
other
intellectual
property
Because
of
this,
you
should
only
connect
your
DVD
rights owned
by
Macrovision
Corporation
and other
player
directly
to
your
TV,
not
to
a
VCR.
Connecting
rights
owners.
Use
of
this copyright
protection
techto
a
VCR
results
in
a
distorted
picture
from
copynology must
bediscs.
auzthorized by Macrovision
protected
DVD
Corporation,
and is intended for home and other
This
product
incorporates
copyright
protection
limited
viewing
uses only unless
otherwise
authotechnology
that is protected
by methods
claims
rized by Macrovision
Corporation.
Reverse
engi-of
certain
patents andisother
intellectual property
neeringU.S.
or disassembly
prohibited.
rights owned by Macrovision Corporation and other
rights
owners. Use of thisSCAN
copyrightOUTPUTS
protection techPROGRESSIVE
nology
must be auzthorized by Macrovision
(525p)
Corporation, and is intended for home and other
limited
viewing uses
only unless
“CONSUMERS
SHOULD
NOTE otherwise
THAT NOTauthoALL
rized
MacrovisionTELEVISION
Corporation. SETS
Reverse
engiHIGHby
DEFINITION
ARE
FULLY
neering
or disassembly
is prohibited.
COMPATIBLE
WITH THIS
PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PROGRESSIVE
OUTPUTS
PICTURE, IN CASE OF SCAN
525 PROGRESSIVE
(525p)
SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CON“CONSUMERS
SHOULD
NOTE THAT
NOT ALL
NECTION TO THE
‘STANDARD
DEFINITION’
OUTHIGH
DEFINITION
TELEVISION
SETS ARE FULLY
PUT. IF
THERE ARE
QUESTIONS
COMPATIBLE
WITH THIS
PRODUCT
AND MAY
REGARDING YOUR
TV SET
COMPATIBILITY
CAUSE
ARTIFACTS
TO BE
DISPLAYED
THE
WITH THIS
MODEL 525p
DVD
PLAYER, IN
PLEASE
PICTURE,
CASE OF 525
PROGRESSIVE
CONTACT IN
SAMSUNG'S
CUSTOMER
SERVICE
SCAN
PICTURE PROBLEMS, IT IS RECOMCENTER.”
MENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS
REGARDING YOUR TV SET COMPATIBILITY
WITH THIS MODEL 525p DVD PLAYER, PLEASE
CONTACT SAMSUNG'S CUSTOMER SERVICE
CENTER.”
Disc Type and Characteristics
Disc Types (Logos)
Recording Types
DVD
Audio
+
Video
VIDEO-CD
Audio
+
Video
AUDIO-CD
Disc Size
Max. Playing Time
Characteristics
12 Cm
Single-sided 240 min.
Double-sided 480 min.
8 Cm
Single-sided 80 min.
Double-sided 160 min.
- DVD contains excellent sound
and video due to Dolby Digital
and MPEG-2 system.
- Various screen and audio functions can be easily selected
through the on-screen menu.
12 Cm
74 min.
8 Cm
20 min.
12 Cm
74 min.
8 Cm
20 min.
Audio
Disc Markings
~
PAL
Play Region Number
PAL broadcast system in
U.K, France, Germany, etc.
Dolby Digital disc
STEREO
DIGITAL
SOUND
Stereo disc
Digital Audio disc
DTS disc
MP3 disc
You must only insert one DVD disc at a
time. Inserting two or more discs will not
allow to play them back and it may cause
damage to the DVD player.
- Video with CD sound, VHS quality & MPEG-1 compression technology.
- CD is recorded as a Digital
Signal with better audio quality,
less distortion and less deterioration of audio quality over time.
Region Number
Both the DVD player and the discs are coded
by region. These regional codes must match in
order for the disc to play. If the codes do not
match, the disc will not play.
The Region Number for this player is
described on the rear panel of the player.
DivX Certification
DivX, DivX Certified, and associated logos are trademarks of
DivXNetworks, Inc and are used
under license.
5
English
This DVD player is capable of playing the following types of discs with the corresponding logos:
Description
Description
Front
Front Panel
Panel Controls
Controls
11
22
33
1.
1. STANDBY/ON
STANDBY/ON (( ))
When
WhenSTANDBY/ON
STANDBY/ONisispressed
pressedon,
on,the
theindicator
indicator
goes
goesout
outand
andthe
theplayer
playerisisturned
turnedon.
on.
2.
2. STANDBY
STANDBY indicator
indicator
When
Whenthe
theunit
unitisisfirst
firstplugged
pluggedin,
in,this
thisindicator
indicator
lights.
lights.
3.
3. DISC
DISC TRAY
TRAY
Place
Placethe
thedisc
dischere.
here.
44
55
66
4.
4. DISPLAY
DISPLAY
Operation
Operationindicators
indicatorsare
aredisplayed
displayedhere.
here.
5.
5. OPEN/CLOSE
OPEN/CLOSE /STOP
/STOP (( ))
Stops
Stopsdisc
discplay.
play.
Press
Presstotoopen
openand
andclose
closethe
thedisc
disctray.
tray.
6.
))
6. PLAY/PAUSE
PLAY/PAUSE ((
Begin
Beginor
orpause
pausedisc
discplay.
play.
Front
Front Panel
Panel Display
Display
Total
Total playing
playing time/Displays
time/Displays various
various messages
messages concerning
concerning operations
operations such
such as
as PLAY,
PLAY,
STOP,
STOP, LOAD
LOAD ...
...
nodSC:
nodSC:No
Nodisc
discloaded.
loaded.
OPEn:
OPEn:The
Thedisc
disctray
trayisisopen.
open.
LOAd:
LOAd:Player
Playerisisloading
loadingdisc
discinformation.
information.
66
Rear Panel
English
4
1
1.
2
3
- If Component(P-SCAN) Video Output is selected in Setup Menu, progressive scan mode will
work.
- If Component(I-SCAN) Video Output is selected in Setup Menu, interlaced scan mode will
work.
5.1CH ANALOG AUDIO OUT
JACKS
- Connect to an amplifier with 5.1ch analog input
jacks.
2.
3.
VIDEO OUT JACK
- Use a video cable to connect to the Video
input jack on your television.
- The Video Output in Setup Menu must be set
to Component(I-SCAN).
COMPONENT VIDEO OUT
JACKS
- Use these jacks if you have a TV with
Component Video in jacks. These jacks provide PR, PB and Y video.
4.
DIGITAL AUDIO OUT JACKS
- Use coaxial digital cable to connect to a compatible Dolby Digital receiver.
- Use coaxial digital cable to connect to an A/V
Amplifier that contains a Dolby Digital, MPEG2
or DTS decoder.
Note
- Consult your TV User’s Manual to find out if your TV supports Progressive Scan.
If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan
settings in the TV’s menu system.
- See pages 27-28 to get more information on how to use the setup menu.
7
DVD-P182-XTL
2/1/08
12:27 PM
Page 8
Tour of the Remote Control
1
15
16
5.
SEARCH Buttons (
)
/
Allow you to search forward/backward through a disc.
6.
VIDEO SEL.Button
Change video output mode
7.
SKIP Buttons (
)
/
Use to skip the title, chapter or track.
STOP Button (
)
8.
9.
2
MENU Button
Brings up the DVD player’s menu.
›/‚,¥/Š Buttons
10. ENTER/›
This button functions as a toggle switch.
17
3
4
5
6
7
8
9
18
19
20
21
10
11
12
13
22
23
24
14
25
11. EZ VIEW Button
The aspect ratio of a picture can easily be adjusted
according to the screen size of your TV (16:9 or 4:3)
12. DISC MENU Button
Brings up the Disc menu.
13. OPEN/CLOSE (
) Button
To open and close the disc tray
14. AUDIO Button
Use this button to access various audio functions on a disc.
15. DVD Button
Use to operate DVD
16. TV Button
Use to operate TV
17. STEP /TV SOURCE Button
Advances play one frame at a time.
18. TV CH Buttons (
Use to change channel.
/
)
19. SUBTITLE Button
20. PLAY/PAUSE Button (
Begin/Pause disc play.
21. RETURN Button
Returns to a previous menu.
1.
DVD Power Button
Turns the power on or standby.
2.
NUMBER Buttons
3.
ZOOM Button/-/-Enlarge DVD Picture or use this button to select
the channel of TV program by inserted the channel
number (TV mode).
4.
8
TV VOLUME
TV VOL(+,-) button
)
22. INFO Button
Displays the current disc mode.
23. CANCEL Button
Use to remove menus or status displays from the
screen.
24. REPEAT A-B Button
Allows you to repeat A-B disc.
25. REPEAT Button
Allows you to repeat play a title, chapter, track, or disc.
CONNECTIONS
The following shows examples of connections commonly used to connect the DVD player with a TV and
other components.
Before Connecting the DVD Player
- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
- Refer to the user’s manual of the additional components you are connecting for more information on those
particular components.
Connection to a TV (For Video)
1
Using video/audio cables, connect the VIDEO
(yellow)/AUDIO (red and white) OUT terminals of 5.1CH
(front L-R) on the rear of the DVD player to the VIDEO (yellow)/AUDIO (red and white) IN terminals of TV.
2
Turn on the DVD player and TV.
RED
YELLOW
WHITE
Audio Cable
Video Cable
RED
3
WHITE
YELLOW
Press the TV/VIDEO button on the TV's remote
control to select Video.
Note
- Noise may be generated if the audio cable is too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 12 to 14)
- The number and position of terminals can vary depending on your TV set. Please refer to the user's manual of the TV.
- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) 5.1CH(Front LR) terminal of the DVD player.
- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the Video
Output mode changes in the following sequence: (I-SCAN ➝ P-SCAN).
9
English
Choosing a Connection
Connection to a TV (Interlace)
- Connecting to your TV using Component video cables.
- You will enjoy high quality and accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images. (Audio
signals are delivered through the audio output.)
1
Using component video cables (not included), connect the
COMPONENT VIDEO OUT terminal on the rear of the
DVD player to the COMPONENT IN terminal of TV.
2
Using the audio cables, connect the AUDIO (red and
white) OUT terminals of 5.1CH (Front L-R) on the rear of
the DVD player to the AUDIO (red and white) IN terminals
of TV. Turn on the DVD player and TV.
BLUE
RED
GREEN
RED
WHITE
Component cable
(not included)
Audio Cable
3
RED
WHITE
RED
BLUE GREEN
Press the TV/VIDEO button on the TV's remote control to
select Component or DVD.
4
Set the Video Output to Component (I-SCAN) in the
Display Setup menu. (See pages 27-28)
Note
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 12 to 14)
- The component terminal of TV can be marked by “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “PR, PB, Y”
depending on the manufacturer. The number and position of terminals can vary depending on the TV set.
Please refer to the user's manual of the TV.
10
Connection to a TV (Progressive)
1
2
Using the audio cables, connect the AUDIO (red and
white) OUT terminals of 5.1 CH (Front L-R)on the rear of
the DVD player to the AUDIO (red and white) IN terminals
of TV. Turn on the DVD player and TV.
3
BLUE
RED
English
Using component video cables (not included), connect the
COMPONENT VIDEO OUT terminal on the rear of the
DVD player to the COMPONENT IN terminal of TV.
GREEN
RED
WHITE
Component cable
(not included)
Audio Cable
RED
WHITE
RED
BLUE GREEN
Press the input selector on your TV remote control until the
Component signal from the DVD player appears on the TV
screen.
4
Set the Video Output to Component (P-SCAN) in the
Display Setup menu. (See pages 27 to 28)
To see the progressive video output,
-You
Consult
TVsupporting
User’s Manual
to find out
need ayour
TV set
the progressive
scanif your TV supports Progressive Scan. If Progressive
Scan isfunction.
supported,
follow
TV up
User’s
Manual regarding Progressive Scan settings in the TV’s
input
And you
havethe
to set
the TV
menu system.
- Depending on your TV, the connection method may differ from the illustration above.
Note
- What is "Progressive Scan"?
Progressive scan has twice as many scanning lines as the interlace output method has. Progressive
scanning method can provide better and clearer picture quality.
11
Connection to an Audio System (2 Channel Amplifier)
1
Using the audio cables, connect the AUDIO (red and
white) OUT terminals of 5.1 CH (Front L-R) on the rear of
the DVD player to the AUDIO (red and white) IN terminals of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO,COMPONENT OUT terminals on the rear of the DVD player to
the VIDEO, COMPONENT IN terminal of your TV.
3
Turn on the DVD player, TV, and Amplifier.
RED
WHITE
Audio Cable
RED
WHITE
4
Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See
(See page
pages25-27)
27)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
12
Connection to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)
1
English
If using a coaxial cable (not included), connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the
DVD player to the DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO,COMPONENT OUT terminals on the rear of the DVD player to
the VIDEO, COMPONENT IN terminal of TV.
3
Turn on the DVD player, TV, and Amplifier.
Coaxial Cable
(not included)
4
Press the input select button of the Amplifier to select
external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 25 to 27)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
13
Connection to a 5.1CH Analog Amplifier
1
If using audio cables for 5.1 CH Analog Amplifier (not
included) connect the 5.1CH ANALOG AUDIO OUT terminals on the rear of the DVD player to the 5.1CH ANALOG
AUDIO IN terminals of the 5.1CH Analog Amplifier.
2
Using the video signal cable(s), connect the VIDEO, COMPONENT terminals on the rear of the DVD player to the
VIDEO,COMPONENT terminals of your TV as described
on pages 9 to 11.
3
RED
RED
WHITE
WHITE
BLACK
BLACK
Turn on the DVD player, TV, and Amplifier.
4
5.1ch Analog
Amplifier
Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 25 to 27)
- The position of terminals may vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
14
DVD-P182-XTL u
1/31/08
4:17 PM
Page 15
Playing a Disc
Before Play
- Turn on your TV and set it to the correct Video
Input by pressing TV/VIDEO button on the TV
remote control.
- If you connected an external Audio System, turn
on your Audio System and set it to the correct
Audio Input.
After plugging in the player, the first time you press the DVD
POWER button, this screen comes up: If you want to select
a language, press a NUMBER button. (This screen will only
appear when you plug in the player for the first time.)
If the language for the startup screen is not set, the settings
may change whenever you turn the power on or off.
Therefore, make sure that you select the language you want
to use.
Once you select a menu language, you can change it by
pressing the
button on the front panel of the unit for more
than 5 seconds with no disc in the unit. Then the SELECT
MENU LANGUAGE window appears again where you can
reset your preferred language.
SELECT MENU LANGUAGE
Press
1
for English
Touche
2
pour Français
Drücken Sie
3
für Deutsch
Pulsar
4
para Español
Premere
5
per Italiano
Druk op
6
voor Nederlands
Playback
1. Press the OPEN/CLOSE ( ) button. The STANDBY
indicator light goes out and the tray opens.
2. Place a disc gently into the tray with the disc’s label facing
up.
- You must only insert one DVD disc at a time.
Inserting two or more discs will not allow to play
them back and it may cause damage to the DVD
player.
3. Press the PLAY/PAUSE ( ) button or OPEN/ CLOSE
( ) button to close the disc tray.
- When you stop disc play, the player remembers
where you stopped, so when you press
PLAY/PAUSE ( ) button again, it will pick up where
you left off. (unless the disc is removed or the player
is unplugged, or if you press the STOP ( ) button
twice.)
4. Stopping Play
Press the STOP ( ) button during play.
5. Removing Disc
Press the OPEN/CLOSE ( ) button.
6. Pausing Play
Press the PLAY/PAUSE ( ) or STEP button on the
remote control during play.
- Screen stops, no sound.
To resume, press the PLAY/PAUSE ( )
button once again.
7. Step Motion Play (Except CD)
Press the STEP button on the remote control during play.
- Each time the button is pressed, a new frame will
appear.
- No sound is heard during STEP mode.
- Press the PLAY/PAUSE ( ) button to resume
normal play.
- You can only perform step motion play in the
forward direction.
8. Slow Motion Play
Press and hold the SEARCH ( / ) button to choose
the play speed between 1/8, 1/4 and 1/2 of normal during
PAUSE or STEP mode.
- No sound is heard during slow mode.
- Press the PLAY/PAUSE ( ) button to resume
normal play.
- Reverse slow motion play will not work.
Note
- If the player is left in the stop mode for more
than one minute without any user interaction, a
screen saver will be activated. Press the
PLAY/PAUSE ( ) button to resume normal play.
- If the player is left in the stop mode for more than
about 30 minutes, the power will automatically
shut off. (Automatic Power-Off Function)
- If the player is left for about 5 minutes in pause
mode, it will stop.
- This (
) icon indicates an invalid button press.
15
English
BASIC FUNCTIONS
Using the Search and Skip
Functions
During play, you can search quickly through a chapter or track, and use the skip function to jump to the
next selection.
Searching through a Chapter or
Track
During play, press the SEARCH ( or
) button on
the remote control for more than 1 second.
DVD
2X, 4X, 64X, 128X
VCD
4X, 8X
CD
2X, 4X, 8X
2. Press the �/��buttons to select the desired item.
- Only Menu Off is available for VCD2.0. Each press of
the DISC MENU button toggles between Menu On and
Menu Off.
3. Press the �/� buttons to make the desired setup and then
press the ENTER button.
- You may use the number buttons of the remote control
to directly access a title, chapter or to start the
playback from the desired time.
4. To make the screen disappear, press the CANCEL button
again.
Note
To access the desired title when there is
more than one in the disc. For example, if
there is more than one movie on a DVD,
each movie will be identified.
Note
- The speed marked in this function may be different from
the actual speed of playback.
- No sound is hearing during search mode (Except CD).
Chapter
Allows playback of the film from a desired
time. You must enter the starting time as a
reference.The time search function does not
operate on some disc.
Skipping Tracks
During play, press the SKIP (
or
) button.
- When playing a DVD, if you press the SKIP (
) button, it
moves to the next chapter. If you press the SKIP (
)
button, it moves to the beginning of the chapter. One more
press makes it move to the beginning of the previous
chapter.
- When playing a VCD 2.0 in Menu Off mode, or a VCD 1.1
or a CD, if you press the SKIP (
) button, it moves to
the next track. If you press the SKIP (
) button, it moves
to the beginning of the track. One more press makes it
move to the beginning of the previous track.
- If a track exceeds 15 minutes when playing a VCD and
you press the
If you press the
button, it moves forward 5minutes.
button, it moves backward 5 minutes.
Note
Only Menu Off is available for VCD2.0. Each press of the
DISC MENU button toggles between Menu On and Menu
Off.
Using the Display Function
When Playing a DVD/VCD/MPEG4
1. During play, press the INFO button on the remote control.
16
Most DVD discs are recorded in chapters so
that you can quickly find a specific passage
(similar to tracks on an VCD).
Audio
Refers to the language of the film soundtrack.
In the example, the soundtrack is played in
English 5.1CH. A DVD disc can have up to
eight different soundtracks.
Refers to the subtitle languages available in
the disc. You will be able to choose the
subtitle languages or, if you prefer, turn them
off from the screen. A DVD disc can have up
to 32 different subtitles.
To access the desired Bookmark or Angle
function.
Some DVD discs are have more angle function from any picture.
Bookmark function make you easily and
quickly to find a track or chapter from DVD.
Using the Disc and Title
Menu
Using the Disc Menu
1. During Stop mode, press the MENU button on the remote
control.
2. Press the �/� buttons to select Disc Menu, then press the
� or ENTER button.
Press ENTER key
for Disc Menu
Note
Using the A-B Repeat function
- Depending on a disc, the Disc Menu may not work.
- You can also use the Disc Menu, using the DISC
MENU button on the remote control.
- Only Menu Off is available for VCD2.0. Each press of
the DISC MENU button toggles between Menu On and
Menu Off.
1. Press the REPEAT A-B button at the point where you
want repeat play to start (A).
2. Press the REPEAT A-B button at the point where you
want the repeat play to stop (B).
3. To return to normal play, press the CANCEL button.
1. During stop mode, press the MENU button on the remote
control.
English
DVD/VCD
Using the Title Menu
Repeat A-
2. Press the �/� buttons to select Title Menu, then press
the � or ENTER button.
Repeat A-B
Press ENTER key
for Title Menu
Note
- Depending on a disc, the Title Menu may not
work.
- Title Menu will only be displayed if there are at
least two titles in the disc.
Repeat Play
Repeat the current track, chapter, title, a chosen
section (A-B), or all of the disc.
When playing a DVD/VCD
1. Press the REPEAT button on the remote control.
Repeat screen appears.
2. Press the �/� buttons to select Chapter, Title or A-B,
then press the ENTER button.
- DVD repeats play by chapter or title, VCD
repeat play by disc or track.
- Chapter : repeats the chapter that is playing.
- Title : repeats the title that is playing.
- Disc : repeats the disc that is playing.
- Track : repeats the track that is playing.
- A-B: repeats a segment of the disc that you select.
Not
- A-B REPEAT allows you to set point(B) until at
least 5 seconds of play back time has elapsed
after point (A) has been set.
- Depending on a disc, the Repeat function may
not work.
- Only Menu Off is available for VCD2.0. Each
press of the DISC MENU button toggles
between Menu On and Menu Off.
Slow Play
This feature allows you slowly to repeat scenes containing sports, dancing, musical instruments being
played etc., so you can study them more closely.
When playing a DVD
1. During play, press the PLAY/PAUSE (
) button.
2. Press and hold the SEARCH ( / ) button to choose the
play speed between 1/8, 1/4 and 1/2 of normal during
PAUSE or STEP mode.
DVD
Off
01
T
01 A - B
ENTER REPEAT
01 A - B
ENTER REPEAT
VCD
Off
T
01
D
17
If you are using a 4:3 TV
ADVANCED
FUNCTIONS
For 16:9 aspect ratio discs
Adjusting the Aspect Ratio
(EZ View)
To play back using aspect ratio
(DVD)
Press the EZ VIEW button.
- The screen size changes when the button is pressed
repeatedly.
- The screen zoom mode operates differently depending on the
screen setting in the Display Setup menu.
- To ensure correct operation of the EZ VIEW button, you
should set the correct aspect ratio in the Display Setup
menu. (See pages 27 to 28).
4:3 letter box
EZ VIEW
If you are using a 16:9 TV
For 16:9 aspect ratio discs
- WIDE SCREEN
Displays the content of the DVD title in 16:9 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the black bars at
the top and bottom of the screen will disappear. The picture
will look vertically stretched. (Depending on a type of disc,
the black bars may not disappear completely.)
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarge
- 4:3 Letter Box
Displays the content of the DVD title in 16:9 aspect ratio. The
black bars will appear at the top and bottom of the screen.
- 4:3 Pan&Scan
The left and right portions of the screen are cut off and the
central portion of the 16:9 screen is displayed.
- SCREEN FIT
The top and bottom portions of the screen are cut off and a
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarged.
For 4:3 aspect ratio discs
- Normal Screen
Displays the content of the DVD title in 4:3 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off and the
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are cut
off and the central portion of the screen is enlarged.
Note
This function may behave differently depending on
the type of disc.
Selecting the Audio
Language
You can select a desired audio language quickly and
easily with the AUDIO button.
Using the AUDIO button
1. Press the Audio button. The Audio changes when the audio
button is press repeatedly.
The audio languages are represented by
abbreviations.
DVD
For 4:3 aspect ratio discs
- Normal Wide
Displays the content of the DVD title in 16:9 aspect ratio.
The picture will look horizontally stretched.
- SCREEN FIT
The top and bottom portions of the screen are cut off and
the full screen appears.
The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are
cut off and the central portion of the screen is enlarged.
- Vertical Fit
When a 4:3 DVD is viewed on a 16:9 TV, black bars will
appear at the left and right of the screen in order to prevent
the picture from looking horizontally stretched.
18
5.1CH
When playing a VCD, you
can select among Stereo,
Left or Right.
AUDIO
VCD
Stereo
AUDIO
Press Audio button at remocon repeatedly to select the
desired audio on MPEG4.
PCM 1/2
AUDIO
2. To remove the AUDIO icon, press the CANCEL or RETURN button.
Note
- This function depends on audio languages are
encoded on the disc and may not work.
- A DVD disc can contain up to 8 audio languages.
- To have the same audio language come up
whenever you play a DVD;
Refer to “Using the Audio Language” on page
25.
Selecting the Subtitle
Language
You can select a desired subtitle quickly and easily
with the SUBTITLE button.
Using the SUBTITLE button (DVD)
1. Press the SUBTITLE button. The subtitle languages are
represented by abbreviations. The subtitle changes when
the button is pressed repeatedly.
Note
- You have to change the desired subtitle in the
Disc Menu, according to discs. Press the DISC
MENU button.
- This function depends on what subtitles are
encoded on the disc and may not work on all
DVDs.
- A DVD disc can contain up to 32 subtitle
languages.
- To have the same subtitle language come up
whenever you play a DVD; Refer to “Using the
Subtitle Language” on page 25.
Changing the Camera
Angle
When a DVD contains multiple angles of a particular
scene, you can use the ANGLE function.
Using the ANGLE Function (DVD).
If the disc contains multiple angles, the ANGLE
appears on the screen.
1. During play, press the INFO button on the remote control.
2. Press the �/� buttons to select Shortcut.
3. Press the �/� buttons to select Angle, then press ENTER
button.
DVD
Off
SUBTITLE
4/6
MPEG4
Subtitle Selection
External Subtitle option
will appear, depends on
the DivX disc.
External Subtitle Off
readme.TXT
Non- standard fonts are not supported
Enter
Return
Menu
Press SUBTITLE button at remocon repeatedly to select the
desired subtitle language on MPEG4.
MPEG4
1/5
Using the Instant
Replay/Skip Function
Using the Instant Replay function
(DVD)
If you miss a scene, you can see it again using this
function.
SUBTITLE
If you press the INSTANT REPLAY button, the current scene
moves backward about 10 seconds, and plays back.
2. To remove the SUBTITLE icon, press the CANCEL or
RETURN button.
19
English
MPEG4
- Playback will skip ahead 10 seconds.
1 2 -
Note
Depending on the disc, these functions may not
work.
Using the Instant Skip function
Using the Bookmark
(DVD)
Use
this function to skip playback about 10 seconds
Function
ahead of the current scene.
This feature lets you bookmark sections of a DVD or
Press
INSTANT
SKIP button.
VCD the
(Menu
Off mode)
so you can quickly find them
-atPlayback
skip ahead 10 seconds.
a later will
time.
Using the Bookmark Function
Note
(DVD/VCD)
Depending on the disc, these functions may not
work.
1. During play, press the INFO button on the remote control.
2. Press the �/� buttons to select Shortcut.
Using the Bookmark
DVD
Function
1. During play, press the INFO button on the remote control.
2.
�/�buttons
buttonstotoselect
selectShortcut.
Bookmark(except VCD),
3. Press
Press the
the �/�
then press the ENTER button.
DVD
4. When you reach the scene you want to mark, press the
ENTER button. Up to three scenes may be marked at a time.
1 - -
ENTER button. Up to three scenes may be marked at a time.
CANCEL
Note
20
- Only Menu Off is available for VCD2.0. Each
press of the DISC MENU button toggles
between Menu On and Menu Off.
- Depending on a disc, the Bookmark function
may not work.
20
Recalling a Marked Scene
Clearing a Bookmark
1~3. The first 1~3 steps are the same as those for “Using the
1~3. The first 1~3 steps are the same as those for “Using the
Bookmark Function” on page 20.
Bookmark Function” on page 20.
4. Press the �/� buttons to select a marked scene.
4. Press the �/� buttons to select the bookmark number you
1 2 CANCEL
want to delete.
5. Press the CANCEL button to delete a bookmark number.
5. Press the PLAY/PAUSE (
scene.
1 2 3
CANCEL
) button to skip to the marked
Function
1~3. The first 1~3 steps are the same as those for “Using the
Using the Zoom Function
Bookmark Function” on page 20.
(DVD/VCD)
4. Press the �/� buttons to select the bookmark number you
to play
delete.
1. want
During
or pause mode, press the ZOOM button on the
remotethe
control,
press
the ENTER
button.
5. Press
CANCEL
button
to delete
a bookmark number.
2. Press the ������� buttons to select the part of the
screen you want to zoom in on. 1 2 3
CANCEL
- During DVD play, press ENTER to zoom in
2X/4X/2X/Normal in order.
- During VCD play, press ENTER to zoom in
Using
theinZoom
Function
2X/4X/2X/Normal
order.
Using the Zoom Function
(DVD/VCD)
CANCEL
Note
- Only Menu Off is available for VCD2.0. Each
press of the DISC MENU button toggles
between
Menu
On and
Menu
Off.
buttons
to select
Bookmark(except
VCD),
3. Press
the �/�
-then
Depending
a disc,
the Bookmark function
press the on
ENTER
button.
may you
notreach
work.the scene you want to mark, press the
4. When
1 - -
) button to skip to the marked
Clearing
Bookmark
Usingathe
Zoom
This feature lets you bookmark sections of a DVD or
VCD (Menu Off mode) so you can quickly find them
VCD
at a later time.
Using the Bookmark Function
(DVD/VCD)
VCD
5. Press the PLAY/PAUSE (
scene.
CANCEL
1. During play or pause mode, press the ZOOM button on the
remote control, press the ENTER button.
2. Press the ������� buttons to select the part of the
screen you want to zoom in on.
- During DVD play, press ENTER to zoom in
2X/4X/2X/Normal in order.
- During VCD play, press ENTER to zoom in
2X/4X/2X/Normal in order.
Clips Menu for
MP3/WMA/JPEG/CD
Audio/MPEG4
- To select the Sub-Folder
Press the �/� buttons to highlight right window.
Press the �/� buttons to select the desired folder,
then press ENTER.
Open the disc tray.
Place the disc on the tray.
Close the tray.
The tray closes and this
screen displays.
Stop
Off
00:00:00
Root
WMA
JPEG
English
CD Audio or discs with MP3/WMA/JPEG/MPEG4
contain individual songs and/or pictures that can be
organized into folders as shown below. They are similar to how you use your computer to put files into different folders.
Parent Folder
MP3
MUSIC
Current Folder
1st
Sub-Folders
2nd
SONG FILE 1
Peer Folders
SONG FILE 2
SONG FILE 3
-
: Name of currently playing file.
-
: Current Playback Time.
-
: Current Playback Mode : There are four
modes. They can be selected in order by
pressing the REPEAT button.
- Off: Normal Playback
- Track: Repeats the current track.
- Folder: Repeats the current folder.
- Random: Files in the disc will be played
in random order.
-
: MP3 file icon. -
: Folder Icon.
-
: WMA file icon. -
: Current Folder icon.
-
: JPEG file icon.
-
: AVI file icon.
-
: CD Audio file icon.
MPEG4 FILES
MP3/WMA/CD Audio Playback
1. Open the disc tray. Place the disc on the tray. Close the tray.
- Only one kind of file is played back when a disc or a
folder contains both MP3 and WMA files.
2. Press the �/� or �/� buttons to select a song file.
Press ENTER to begin playback of the song file.
Play
Off
Repeat
Folder Selection
The folder can be selected in Play mode.
- To select the Parent Folder
Press the RETURN button to go to parent folder, or press the
�/� buttons to select “..” and press ENTER to go to the
parent folder.
- To select the Peer Folder
Press the �/� buttons to highlight left window. Press the
�/� buttons to select the desired folder, then press
ENTER.
Repeat
Repeat/Random playback
Press the REPEAT button to change the playback mode. There
are four modes, such as Off, Track, Folder and Random.
- Off: Normal Playback
- Track: Repeats the current song file.
- Folder: Repeats the song files which have the same
extension in the current folder.
- Random: Song files which have the same extension will be
played in random order.
To resume normal play, press the CANCEL button.
21
CD-R MP3/WMA file
When you record MP3 or WMA files on CD-R, please refer
to the following.
- Your MP3 or WMA files should be ISO 9660 or JOLIET
format.
ISO 9660 format and Joliet MP3 or WMA files are
compatible with Microsoft's DOS and Windows, and with
Apple's Mac. This format is the most widely used.
- When naming your MP3 or WMA files, do not exceed 8
characters, and enter “.mp3, .wma” as the file extension.
General name format : Title.mp3. or Title.wma. When
composing your title, make sure that you use 8 characters or
less, have no spaces in the name, and avoid the use of
special characters including: (.,/,\,=,+).
- Use a decompression transfer rate of at least 128 Kbps
when recording MP3 files.
Sound quality with MP3 files basically depends on the rate of
compression/decompression you choose. Getting CD audio
sound requires an analog/digital sampling rate, that is
conversion to MP3 format, of at least 128 Kbps and up to 160
Kbps. However, choosing higher rates, like 192 Kbps or more,
only rarely give better sound quality. Conversely, files with
decompression rates below 128 Kbps will not be played
properly.
- Use a decompression transfer rate of at least 64Kbps
when recording WMA files.
Sound quality with WMA files basically depends on the rate of
compression/decompression you choose.
Getting CD audio sound requires an analog/digital sampling
rate, that is conversion to WMA format, of at least 64Kbps
and up to 192Kbps. Conversely, files with decompression
rates below 64Kbps or over 192Kbps will not be played
properly.
- Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected to
prevent illegal copying. These files are of the following types:
TM
Windows Media (registered trade mark of Microsoft Inc) and
TM
SDMI (registered trade mark of The SDMI Foundation). You
cannot copy such files.
- Important:
The above recommendations cannot be taken as a
guarantee that the DVD player will play MP3 recordings, or as
an assurance of sound quality. You should note that certain
technologies and methods for MP3 file recording on CD-Rs
prevent optimal playback of these files on your DVD player
(degraded sound quality and in some cases, inability of the
player to read the files).
- This unit can play a maximum of 500 files and 500 folders
per disc.
22
MPEG4 Playback
MPEG4 Play Function
AVI files are used to contain the audio and video
data. Only AVI format files with the “.avi” extensions
can be played.
1. Open the disc tray. Place the disc on the tray.
Close the tray.
2. Press the �/� or �/��buttons to select an avi file
(DivX/XviD), then press the ENTER button.
Stop
Off
00:00:00
Repeat Playback
Press the REPEAT button to change playback mode. There
are 4 modes, such as Off, Folder, Title an A-B.
-Folder : Repeats the AVI files which have the same exten
sion in the current folder.
-Title : repeats the title that is playing.
-A-B : repeats a segment of the file that you selecting.
MPEG4 Function Description
(
(
Function
Description
Reference page
Skip
or
During play, press the
or
button, it moves forward or
backward 5 minutes.
During play, press the SEARCH (
or
) button and press again to
search at a faster speed. Allows you
to search at a faster speed in an
AVI file. (2X, 4X, 8X)
Allows you to search at a slower
speed in an AVI file. (1/8X, 1/4X,
1/2X)
Each time the STEP button is
pressed, a new frame will
appear.
-
)
Search
or
)
Slow Motion
Play
Step Motion
Play
ZOOM
2X/4X/2X/Normal in order
-
P 15
P 15
P 20
- These functions may not work depending on MPEG4 file.
CD-R AVI file
This unit can play the following video compression formats
within the AVI file format:
- DivX 3.11 contents
- DivX 4 contents (Based on MPEG4 Simple Profile)
- DivX 5 contents (MPEG4 simple profile plus additional features such as bi-directional frames. Qpel and GMC are also
supported.)
- XviD MPEG4 compliant Contents.
This unit supports all resolutions up to maximum below.
DivX5
Bitrate may fluctuate:
720 x 480 @30fps
Device may skip decoding the
720 x 576 @25fps
high bitrate portions and begin
: Maximum bitrate : 4Mbps
decoding again when Bitrate
•
: When this icon is selected and ENTER is
pressed, the pictures change automatically
with about a 6 second interval.
•
: The pictures change automatically with
about a 12 second interval.
•
: The pictures change automatically with
about a 18 second interval.
returns to
normal.
Note
- Some MPEG4 files created on a personal computer may not be play back.
That is why Codec Type, Version and Higher resolution over specification is not supported.
English
DivX3.11 & DivX4 & XviD
Timer :
- This unit supports CD-R/RW written in MPEG4 in
accordance with the “ISO9660 format”.
Picture CD Playback
1. Select the desired folder.
2. Press the �/� buttons to select a Picture file in the clips
menu and then press the ENTER button.
3. Press the INFO button on the remote control to select the
menu you want to view and then press the ENTER button.
Note
- If no buttons on the remote control are pressed
for 10 seconds, the menu will disappear.
- Press the STOP button to return to the clips
menu.
- When playing a Kodak Picture CD, the unit
displays the Photo directly, not the clips menu.
Rotation
: Each time the ENTER button is pressed, the
picture rotates 90 degrees clockwise.
Zoom
: Press the �/� buttons to select the part of the
screen you want to zoom in on.
Press the ENTER button. Each time the ENTER button is pressed, the picture is enlarged up to 2X.
Slide Show
•
: The unit enters slide show mode.
• Before beginning the Slide Show, the picture interval must
be set.
Note
- Depending on a file size, the amount of time
between each picture may be different from the
manual.
- If you don’t press any button, the slide show will
start automatically in about 10 seconds by default.
CD-R JPEG Discs
- Only files with the “.jpg” and “.JPG” extensions can be played.
- If the disc is not closed, it will take longer to start playing and
not all of the recorded files may be played.
- Only CD-R discs with JPEG files in ISO 9660 or Joliet format
can be played.
- The name of the JPEG file may not be longer than 8
characters and should contain no blank spaces or special
characters (. / = +).
- Only a consecutively written multi-session disc can be played.
If there is a blank segment in the multi-session disc, the disc
can be played only up to the blank segment.
- A maximum of 500 images can be stored on a single CD.
- Kodak Picture CDs are recommended.
- When playing a Kodak Picture CD, only the JPEG files in the
pictures folder can be played.
- When playing a Kodak Picture CD, only the JPEG files in the
pictures folder can be played.
- Kodak Picture CD: The JPEG files in the pictures folder can
be played automatically.
- Konica Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- Fuji Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- QSS Picture CD: The unit may not play QSS Picture CD.
- If the number of files in 1 Disc is over 500, only 500 JPEG
files can be played.
- If the number of folders in 1 Disc is over 500, only JPEG
files in 500 folders can be played
23
Setting Up the Language
Features
CHANGING SETUP
MENU
If you set the player menu, disc menu, audio and
subtitle language in advance, they will come up
automatically every time you watch a movie.
Using the Setup Menu
Using the Player Menu Language
The Setup menu lets you customize your DVD player by allowing you to select various language preferences, set up a parental level, even adjust the player to the type of television screen you have.
1. With the unit in Stop mode, press the MENU button.
2. Press the �/� buttons to select Setup, then press the �
or ENTER button.
3. Press the �/� buttons to select Language Setup, then
press the � or ENTER button.
1. With the unit in Stop mode, press the MENU button on the
remote control. Use the �/� buttons to select Setup, then
press the � or ENTER button.
4. Press the �/� buttons to select Player Menu, then press
the � or ENTER button.
5. Press the �/� buttons to select the desired language,
then press the � or ENTER button.
- The language is selected and the screen
returns to Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
Language Setup
�
Audio Setup
�
Display Setup
�
Parental Setup :
�
DivX(R) Registration
�
❶ Language Setup: Setup of the Language.
❷ Audio Setup : Setup of the Audio Options.
❸ Display Setup : Setup of the Display Options. Use to
select which type of screen you want to watch and sever
al display options.
❹ Parental Setup : Setup of the Parental Level. Allows
users to set the level necessary to prevent children from
viewing unsuitable movies such as those with violence,
adult subject matter, etc.
❺ DivX(R) Registration : Please use the Registration code
to register this player with the DivX(R) Video On
Demand format. To learn more go to www.divx.com/vod.
2. Press the �/� buttons to access the different features.
Press the � or ENTER button to access the sub features.
3. To make the setup screen disappear after setting up, press
the MENU button again.
Note
Depending on the disc, some Setup Menu selections may not work.
Using the Disc Menu Language
This function changes the text language only on the
disc menu screens.
1. With the unit in Stop mode, press the MENU button.
2. Press the �/� buttons to select Setup, then press the �
or ENTER button.
3. Press the �/� buttons to select Language Setup, then
press the � or ENTER button.
4. Press the �/� buttons to select Disc Menu, then press
the � or ENTER button.
5. Press the �/� buttons to select the desired language,
then press the � or ENTER button.
- If the selected language is not recorded on the disc,
the original pre-recorded language is selected.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
LANGUAGE SETUP
DivX
24
Using the Audio Language
Using the DivX Subtitle Language
1. With the unit in Stop mode, press the MENU button.
2. Press the �/� buttons to select Setup, then press the �
or ENTER button.
3. Press the �/� buttons to select Language Setup, then
press the � or ENTER button.
4. Press the �/� buttons to select Audio, then press the �
or ENTER button.
ƒ buttons to select the desired language, then
5. Press the œ/�
/ƒ
press the ‹ or ENTER button.
- Select “Original” if you want the default soundtrack
language to be the original language the disc is
recorded in.
- If the selected language is not recorded on the disc, the
original pre-recorded language is selected.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
1. With the unit in Stop mode, press the MENU button.
LANGUAGE SETUP
2. Press the �/� buttons to select Setup, then press the �
or ENTER button.
3. Press the �/� buttons to select Language Setup, then
press the � or ENTER button.
4. Press the �/� buttons to select DivX Subtitle, then press
English
the � or ENTER button.
5. Press the �/� buttons to select the desired language,
then press the � or ENTER button.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the
MENU button.
LANGUAGE SETUP
Player Menu
Disc Menu
Audio
Subtitle
DivX Subtitle
√ Unicode
Western
Turkish
Central
Cyrillic
Greek
Setting Up the Audio
Options
Using the Subtitle Language
1. With the unit in Stop mode, press the MENU button.
2. Press the �/� buttons to select Setup, then press the �
or ENTER button.
3. Press the �/� buttons to select Language Setup, then
press the � or ENTER button.
4. Press the �/� buttons to select Subtitle, then press the �
or ENTER button.
5. Press the �/� buttons to select the desired language,
then press the � or ENTER button.
- Select “Automatic” if you want the subtitle language to
be the same as the language selected as the audio
language.
- Some discs may not contain the language you select as
your initial language; in that case the disc will use its
original language setting.
- The language is selected and the screen returns to
setup menu.
- To make the setup menu disappear, press the MENU
button.
LANGUAGE SETUP
Audio Options allows you to setup the audio device
and sound status settings depending on the audio
system in use.
1. With the unit in Stop mode, press the MENU button.
2. Press the �/� buttons to select Setup, then press the �
or ENTER button.
3. Press the �/� buttons to select Audio Setup, then press
the � or ENTER button.
4. Press the �/� buttons to select the desired item, then
press the � or ENTER button.
�
�
�
�
�
Language Setup
Audio Setup
Display Setup
Parental Setup :
DivX(R)Registration
AUDIO SETUP
Dolby Digital Out
:PCM
MPEG-2 Digital Out
:PCM
Dynamic Compression:On
PCM Down Sampling
:On
Output Channel
:5.1CH
Speaker Setup
�
25
put.
lay
❶ Dolby Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bitstream : Outputs Dolby Digital via the digital out
put.Select Bitstream when connecting to a
Dolby Digital Decoder.
❷ MPEG-2 Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bitstream : Converts to MPEG-2 Digital Bitstream
(5.1CH or 8CH). Select Bitstream when using the
Digital Audio Output.
❸ Dynamic Compression
- On : To select dynamic compression.
- Off : To select the standard range.
❹ PCM Down Sampling
- On : Select this when the Amplifier connected to the
player is not 96KHz compatible. In this case, the
96KHz signals will be down converted to 48KHZ.
- Off : Select this when the Amplifier connected to the
player is 96KHz compatible. In this case, all signals
will be output without any changes.
e
Note
Even when PCM Down sampling is Off
• Some discs will only output down sampled
audio through the digital outputs.
• To make the Setup menu disappear, press the
MENU button.
e
s
❺ Output Channel
- 2 Ch : Select this when using 2 channel connection only.
- 5.1Ch : Select this when using 5.1Ch channel connec
tion.
he
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
Surround Sound Speaker Setup
1. With the unit in Stop mode, press the MENU button.
2. Press the �/� buttons to select Setup, then press the �
or ENTER button.
3. Press the �/� buttons to select Audio Setup, then press
the � or ENTER button.
4. Press the �/� buttons to select Speaker Setup, then
press the � or ENTER button.
5. Press the �/�/�/� buttons to select the desired item,
then press the ENTER button to set the speaker.
Note
To make speaker setup menu appear, Select output
channel to 5.1Ch.
26
AUDIO SETUP
Dolby Digital Out
:PCM
MPEG-2 Digital Out
:PCM
Dynamic Compression:On
PCM Down Sampling
:On
Output Channel
:5.1CH
�
Speaker Setup
Enter
Return
Menu
SPEAKER SETUP
Small
Test
Small
On
Small
User
Small
Small
Note
To make the setup menu disappear, press the MENU
button.
The default settings : FRONT L, R (Small),
CENTER (Small), SURROUND (Small).
Select the size of the speakers to be connected.
❶ Front (FL, FR)
- Large: Normally select this.
- Small: When the sound distorts or the suround
sound effects are difficult to hear, select this.
This activates the Dolby Digital bass redirec
tion circuitry and outputs the bass frequencies
of the speaker from the subwoofer.
❷ Center
- None: If you do not connect a center speaker,
select this.
- Large: Normally select this.
- Small: When the sound distorts, select this.
This activates the Dolby Digital bass redirection circuitry and outputs the bass frequencies
of the center speaker from other speakers.
❸ Surround (SL, SR)
- None: If you do not connect a center speaker,
select this.
- Large (Rear/Side): Normally select either of
these according to the rear speaker’s position.
- Small (Rear/Side): When the sound ditorts or
the surround sound effects are dificult to hear,
select either of these according to the rear
speaker’s position.
This activates the Dolby Digital bass rediretion
circuitry and outputs the bass frequencies of
the rear speaker from other speakers.
Setting up Test
The test output signals come clockwise starting
from the Front Speaker(L).
Adjust Channel Balance so that speakers output
equally in your room.
FRONT(L) ➝ CENTER ➝ SUBWOOFER ➝
FRONT(R) ➝ SURROUND(R) ➝ SURROUND(L)
❷ Still Mode
To make the Setup menu disappear or return to
menu screen during set up, press RETURN button.
• The subwoofer test output signal is lower
than the other speakers.
• The MPEG Multichannel logo is a trademark
registered by PHILIPS Corporation.
• If you set Front (L, R) “Small”, LFE
(Subwoofer) is set “On” automatically.
These options will help prevent picture shake in
still mode and display small text clearer.
- Auto : When selecting Auto, Field/Frame mode
will be automatically converted.
- Field : Select this feature when the screen
shakes in the Auto mode.
- Frame : Select this feature when you want to
see small letters more clearly in the Auto mode.
❸ Screen Messages
Use to turn on-screen messages On or Off.
❹ Black Level
Setting Up the Display
Options
Adjusts the brightness of the screen.(On or Off) It
does not function in Progressive mode.
❺ TV System
Display options enable you to set various video
functions of the player.
1. With the unit in Stop mode, press the MENU button.
2. Press the �/� buttons to select Setup, then press the �
or ENTER button.
3. Press the �/� buttons to select Display Setup, then press
the � or ENTER button.
4. Press the �/� buttons to select the desired item, then
press the � or ENTER button.
Language Setup
�
Audio Setup
�
Display Setup
�
Parental Setup :
�
DivX(R) Registration
�
- NTSC : In case of using NTSC disc
• If your TV system only has PAL-Video input,
you must choose “PAL”. When you choose
“PAL”, Interlace output format is PAL 60 Hz output.
• If your TV system only has NTSC, input you
must choose “NTSC ”.
- PAL : In case of using PAL disc
• If your TV system only has NTSC-Video input,
you must choose “NTSC”.
• If your TV system only has PAL input, you must
choose “PAL ”.
• If you set up the PAL TV system.Still mode
DISPLAY SETUP
Return
Enter
Menu
TV Aspect
Still mode
Screen Messages
Black Level
TV System
Video Output
❶ TV Aspect
Depending on a type of television you have, you
may want to adjust the screen setting (aspect
ratio).
Enter
- 4:3 Letter Box : Select when you want to see
the total 16:9 ratio screen DVD
supplies, even though you have a TV with a 4:3
ratio screen. Black bars will appear at the top
and bottom of the screen.
- 4:3 Pan&Scan : Select this for conventional
size TVs when you want to see the central portion of the 16:9 screen. (Extreme left and right
side of movie picture will be cut off.)
- 16:9 Wide : You can view the full 16:9
picture on your wide screen TV.
DISPLAY SETUP
TV Aspect
Still mode
Screen Messa
Black Level
TV System
Video Output
Enter
Letter Box
Pan&Scan
: Off
: PAL
: I-SCAN
Return
Return
: 4:3 L-Box
: Auto
: On
: Off
Menu
➏ Video Output
Select Video Output.
- I-SCAN: Select when you want to use
Component Interlace (525i) Out.
- P-SCAN: Select when you want to use
Component Progressive (525p) Out.
• If you press the VIDEO SEL. button, Video
output mode is changed in regular sequence
in no disc mode. (I-SCAN ➝ P-SCAN).
• If the Yes/No selection in the Display Setup
sub Menu is not made within 10 seconds,
the screen returns to the previous menu.
Menu
27
English
Note
PARENTAL SETUP
DISPLAY SETUP
TV Aspect
: 4:3 L-Box
Still mode
: Auto
Screen Messages : On
Black Level
: Off
TV System
Video Output I-SCAN
Rating level
: Kids Safe
Change Password
P-SCAN
Enter
Return
Menu
• Consult your TV User’s Manual to find
out if your TV supports Progressive Scan. If
Progressive Scan is supported, follow the TV
User’s Manual regarding Progressive Scan
settings in the TV’s menu system.
• If Video Output is set incorrectly, the screen
may be blocked.
• When the resolution is changed during playback, it may take a few seconds for a normal
image to appear.
Setting Up the Parental
Control
5. Enter your password.
- By default, password is set to 0000.
PARENTAL SETUP
Rating Level
: Kids Safe
Change Password
Enter Password
Enter
Return
Menu
6. Press the �/� buttons to select the Rating Level you want,
then press the � or ENTER button.
e.g) Setting up in Kids Safe.
PARENTAL SETUP
The Parental Control function works in conjunction
with DVDs that have been assigned a rating, which
helps you control the types of DVDs that your family
watches. There are up to 8 rating levels on a disc.
Rating
Rating Level
Level
Change Passwor
Enter
KidsSafe
Safe
√ :Kids
Level 2
Level 3
Level 4
Level 5
Level 6
Return
Menu
Setting Up the Rating Level
1. With the unit in Stop mode, press the MENU button.
2. Press the �/� buttons to select Setup, then press the �
or ENTER button.
Note
• To make the setup menu disappear, press the
MENU button. For example, if you select up to
Level 6, discs that contain Level 7,8 will not play.
Changing the Password
Language Setup
�
Audio Setup
�
Display Setup
�
Parental Setup :
�
DivX(R) Registration
�
3. Press the �/� buttons to select Parental Setup, then
press the � or ENTER button.
Language Setup
�
Audio Setup
�
Display Setup
�
Parental Setup :
�
DivX(R) Registration
�
4. Press the �/� buttons to select Rating Level, then press
the � or ENTER button.
28
1. With the unit in Stop mode, press the MENU button.
2. Press the �/� buttons to select Setup, then press the �
or ENTER button.
Language Setup
�
Audio Setup
�
Display Setup
�
Parental Setup :
�
DivX(R) Registration
�
3. Press the �/� buttons to select Parental Setup, then
press the � or ENTER button. The Enter Password screen
appears. Enter your password.
Language Setup
�
Audio Setup
�
Display Setup
�
Parental Setup :
�
DivX(R) Registration
�
4. Press the �/� button to select Change Password, then
press the � or ENTER button. Enter your password (default
password). Enter the new password again.
PARENTAL SETUP
Rating Level
:Kids Safe
English
Change Password
PARENTAL SETUP
Rating Level
:Kids Safe
Change Password
Enter Password
Enter
Return
Menu
PARENTAL SETUP
Rating Level
:Kids Safe
Change Password
Enter New Password
Setup
Enter
Return
Menu
Note
If you have forgotten your password, see
“Forgot Password” in the Troubleshooting Guide.
29
DVD-P182-XTL u
1/31/08
4:17 PM
Page 31
Troubleshooting
Before requesting service (troubleshooting), please check the following.
Page
No operations can be
performed with the
remote control.
• Check the batteries in the remote control.
They may need replacing.
• Operate the remote control at a distance of no more than 20 feet.
• Remove batteries and hold down one or more buttons for several minutes to drain
the microprocessor inside the remote control to reset it. Reinstall batteries and try
to operate the remote control again.
P3
Disc does not play.
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the DVD.
P5
5.1 channel sound is
not being reproduced.
The
icon appears
on screen.
• 5.1 channel sound is reproduced only when the following conditions are met :
1) The DVD player is connected with the proper Amplifier
2) The disc is recorded with 5.1 channel sound.
• Check whether the disc being played has the “5.1 ch” mark on the outside.
• Check if your audio system is connected and working properly.
• In SETUP Menu, is the Audio Output set to Bitstream?
English
Action
Problem
P 13~15
P25~27
• The features or action cannot be completed at this time because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
Disc Menu doesn’t appear. • Check if the disc has a Menu.
Play mode differs from the • Some of the functions selected in the Setup Menu may not work properly if the
Setup Menu selection.
disc is not encoded with the corresponding function.
P24~29
The screen ratio
cannot be changed.
• The Screen Ratio is fixed on your DVDs.
P27~28
No audio.
• Make sure you have selected the correct Digital Output in the Audio Options
Menu.
P24~29
The screen is blocked
• Press the
button (on front panel) for more than 5 seconds under no disc inside.
All settings will revert to the factory settings.
Forgot password
• Press the
button (on front panel ) for more than 5 seconds under no disc
inside. All settings including the password will revert to the factory settings. Don't
use this unless absolutely necessary.
Other problems.
• Go to the contents of the instruction book and find the section that contains the
explanations regarding the current problem, and follow the procedure once again.
• If the problem still cannot be solved, please contact your nearest authorized service center.
The picture is noisy or
distorted
• Make sure that the disc is not dirty or scratched.
• Clean the disc.
P15
P28~29
P2
31
Specifications
General
Power Requirements
AC 110-240 V, 60/50 Hz
Power Consumption
9W
1.7 Kg
Weight
360mm (W) X 203mm (D) X 37mm (H)
Dimensions
+5°C to +35°C
Operating Temperature Range
Operating Humidity Range
10 % to 75 %
DVD
(DIGITAL VERSATILE DISC)
Disc
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time
(Single Sided, Single Layer Disc) : 135 min.
CD : 12Cm
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
CD : 8Cm
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min. (Video + Audio)
VCD : 12Cm
Video
Output
Composite Video
1 channel : 1.0 Vp-p (75 1 load)
Component Video
Y : 1.0 Vp-p (75 1 load)
Pr : 0.70 Vp-p (75 1 load)
Pb : 0.70 Vp-p (75 1 load)
5.1 Channel
Audio
Output
F/L,F/R,R/L,R/R,CT,S/W
48 kHz Sampling : 4 Hz to 22 kHz
96 kHz Sampling : 4 Hz to 44 kHz
*Frequency Response
*S/N Ratio
110 dB
*Dynamic Range
100 dB
*Total Harmonic Distortion
0.004 %
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications without
notice.
- Weight and dimensions are approximate.
32
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer
care center.
Region
North America
Latin America
Country
CANADA
MEXICO
U.S.A
ARGENTINE
BRAZIL
CHILE
NICARAGUA
HONDURAS
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD & TOBAGO
VENEZUELA
COLOMBIA
BELGIUM
CZECH REPUBLIC
DENMARK
FINLAND
FRANCE
Europe
CIS
Asia Pacific
Middle East &
Africa
Customer Care Center 1-800-SAMSUNG(726-7864)
01-800-SAMSUNG(726-7864)
1-800-SAMSUNG(726-7864)
0800-333-3733
0800-124-421 , 4004-0000
800-SAMSUNG(726-7864)
00-1800-5077267
800-7919267
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
1-800-234-7267
800-7267
1-800-682-3180
1-800-751-2676
1-800-SAMSUNG(726-7864)
0-800-100-5303
01-8000112112
0032 (0)2 201 24 18
844 000 844
Distributor pro Českou republiku:
Samsung Zrt., česka organizační složka
Vyskočilova 4, 14000 Praha 4
70 70 19 70
030-6227 515
3260 SAMSUNG ( 0,15/Min),
08 25 08 65 65 ( 0,15/Min)
Web Site
www.samsung.com/ca
www.samsung.com
www.samsung.com
www.samsung.com/ar
www.samsung.com
www.samsung.com/cl
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com.co
www.samsung.com/be
www.samsung.com/cz
www.samsung.com/dk
www.samsung.com/fi
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/be
www.samsung.com/nl
www.samsung.com/no
www.samsung.com/pl
www.samsung.com/pt
www.samsung.com/sk
www.samsung.com
www.samsung.com/se
www.samsung.com
www.samsung.com/ie
www.samsung.com/at
www.samsung.com/ch
www.samsung.com
www.samsung.kz
www.samsung.uz
GERMANY
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
POLAND
PORTUGAL
SLOVAKIA
SPAIN
SWEDEN
U.K
EIRE
AUSTRIA
SWITZERLAND
RUSSIA
KAZAHSTAN
UZBEKISTAN
KYRGYZSTAN
TADJIKISTAN
UKRAINE
LITHUANIA
LATVIA
ESTONIA
AUSTRALIA
NEW ZEALAND
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
PHILIPPINES
SINGAPORE
THAILAND
TAIWAN
VIETNAM
TURKEY
0900-SAMSUNG(726-7864) ( 0,10/Min)
815-56 480
0 801 801 881 , 022-607-93-33
80820-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
902 10 11 30
0771-400 200
0845 SAMSUNG (7267864)
0818 717 100
0800-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
8-800-555-55-55
8-10-800-500-55-500
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
8-800-502-0000
8-800-77777
800-7267
800-7267
1300 362 603
0800SAMSUNG(726-7864)
800-810-5858 , 010-6475 1880
3698-4698
3030 8282 , 1800 110011
0800-112-8888
0120-327-527
1800-88-9999
1800-10-SAMSUNG(726-7864)
1800-SAMSUNG(726-7864)
1800-29-3232 , 02-689-3232
0800-329-999
1 800 588 889
444 77 11
www.samsung.com
www.samsung.lt
www.samsung.com/lv
www.samsung.ee
www.samsung.com
www.samsung.com/nz
www.samsung.com
www.samsung.com/hk
www.samsung.com
www.samsung.com
www.samsung.com/jp
www.samsung.com/my
www.samsung.com/ph
www.samsung.com
www.samsung.com
www.samsung.com/tw
www.samsung.com
www.samsung.com
SOUTH AFRICA
0860-SAMSUNG(726-7864 )
www.samsung.com
U.A.E
800-SAMSUNG (726-7864), 8000-4726
www.samsung.com
01805 - SAMSUNG(726-7864) (
06-80-SAMSUNG(726-7864)
800-SAMSUNG(726-7864)
0035 (0)2 261 03 710
0,14/Min)
Memo
34
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products,
please contact the SAMSUNG customer care centre.
☎ 3030-8282/1800-1100-11/www.samsung.com
AK68-01505A(01)