Samsung AZ09A7KE User Manual

Window-type Room Air Conditioner ( Cool and Heat )
Climatiseur de type Fenêtre ( Refroidissement et Chauffage )
E F A DB98-05458A(1)
ENGLISH
AZ09F7KE
AZ09A7KE
AZ09F8KE
AZ09A8KE
FRANÇAIS
OWNER’S INSTRUCTIONS
MANUEL D’UTILISATION
Safety Precautions
The following safety precautions must be taken when installing
and using your air conditioner.
1 The air conditioner must be plugged into its own specific power source, which must be
installed in compliance with national wiring, earthing and safety regulations.
Depending on national regulations and your specific installation, you may need to install:
◆ A circuit breaker
For further information on electrical requirements, contact a professional electrician.
This device must be installed according to the national electrical rules.
2 Make sure that the unit is correctly ventilated at all times;
do NOT place clothing or other materials over it.
3 NEVER spill liquids of any kind into the unit.
Should this happen, unplug the unit and contact your installation specialist.
4 Do NOT insert anything between the air outlet blades, as it may damage the inner fan
and you may be hurt. Keep children away from the unit.
5 ALWAYS ensure that the power cable is in good condition.
If the power cord is damaged in any way, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.
6 Do NOT attempt to repair the unit yourself. If it is damaged in any way, contact:
◆ An authorized service center
◆ The dealer from whom you purchased the air conditioner.
7 Do NOT place any brocking objects in front of the unit.
8 If the remote control will not be used for a long time, remove the batteries.
9 Before throwing out the device, it is necessary to pull back the battery cells
and get rid of them safely.
E-2
ENGLISH
Contents
◆ PREPARING YOUR AIR CONDITIONER
■
■
■
■
■
Safety Precautions .........................................................................................
Air Conditioning Unit - Main Parts, Buttons and Display ...............................
Remote Control Buttons .................................................................................
Getting Started ...............................................................................................
Inserting the Remote Control Batteries ..........................................................
2
4
5
6
7
◆ OPERATING YOUR AIR CONDITIONER
■
■
■
■
■
Cooling Your Room ........................................................................................ 8
Heating Your Room ........................................................................................ 9
Airing Your Room ........................................................................................... 10
Adjusting the Air Flow Direction Horizontally .................................................. 11
Adjusting the Air Flow Direction Vertically ...................................................... 11
◆ PROGRAMMING YOUR AIR CONDITIONER
■
■
Switching the Unit Off Automatically (Off Timer) ............................................ 12
Canceling the Off Timer .................................................................................. 12
◆ RECOMMENDATIONS FOR USE
■
■
■
■
■
Operating Recommendation ...........................................................................
Temperature and Humidity Ranges ................................................................
Cleaning Your Air Conditioner ........................................................................
Solving Common Problems ............................................................................
Technical Specifications .................................................................................
◆ METHOD
OF INSTALLATION
13
14
15
17
17
.................................................................................... 18
E-3
Air Conditioning Unit - Main Parts, Buttons and Display
❄ The design and shape are subject to
change according to the model.
Inner air flow blades
(right/left orientation)
Air outlet
Air inlet (inside)
Outer air flow blades
(up/down orientation)
Air filter
(The air filter is
located inside)
Air inlet (Outside)
Ventilation lever
Hr.
C
FAN SPEED
Power plug
(The type of the power
plug may differ
according to the type of
local power supply.)
Temperature/Timer setting
Remote control sensor
Timer indicator
Hr.
C
Temperature
adjustment button
TEMP.
Temperature indicator
Deice indicator
HIGH
Fan speed indicators
RESTART
LOW
Fan speed button
Air flow blade swing button
SWING
COOL
FAN SPEED
FAN
MODE
Operating mode indicators
(HEAT, COOL, FAN)
Operating mode selection
button
POWER
ON/OFF button
Restart Indicator
■
■
E-4
When the power plug is connected,
the indicator comes on.
If a power failure occurs when the air
conditioner is operating, the unit is switched off.
Then the power returns, the air conditioner
starts up again automatically and the restart
indicator blinkes. The indicator lights up
after 2 minutes.
(Only AZ09F8KE / AZ09A8KE)
ENGLISH
Remote Control - Buttons
Operating mode selection buttons
(FAN, HEAT, COOL)
Temperature adjustment buttons
Fan speed adjustment buttons
Timer setting buttons
ON/OFF Button
Air flow blade swing button
E-5
Getting Started
You have just purchased a window-type room air conditioner and it has been installed by your
installation specialist.
Your Owner’s Instructions contain valuable information on using your air conditioner.
Please take the time to read them as they will help you take full advantage of the unit’s functions.
The booklet is organized as follows.
◆ The following figures are shown on pages 4 and 5:
-
Air conditioning unit (main parts, buttons and display)
-
Remote control (buttons)
They will help you find the buttons and understand the symbols displayed.
◆ In the main part of the document, you will find a series of step-by-step procedures for each
function available.
The illustrations in the step-by-step procedures use four different symbols:
PRESS
PUSH
☛
➢
IMPORTANT
NOTE
Moreover, applicable, wherever the illustrations show the positions of the buttons on both the
remote control and the unit itself.
For the...
The illustrations have a...
Remote control
Gray background.
Example:
Unit itself
White background.
Example:
POWER
E-6
ENGLISH
Inserting the Remote Control Batteries
You must insert or replace the remote control batteries when:
◆ You purchase the air conditioner
◆ The remote control does not work correctly
☛
Use two LR03 (R03) 1.5 V batteries. Do not use old
batteries or different kinds of batteries together.
Batteries may be completely discharged after 12 months,
even if they have not actually been used.
1
Push the battery cover on the rear of the remote control with your thumb in
the direction of the arrow and remove it.
2
Insert the two batteries, taking care to respect the polarities:
◆ + on the battery with + on the remote control
◆ – on the battery with – on the remote control
3
Close the cover by sliding it back until it clicks into place.
Result:
You can control all the functions on your air conditioning unit
directly from your seat, using the remote control.
E-7
Cooling Your Room
You must select the Cool mode if you wish to lower the temperature
in your room. You can also set the fan speed.
Remote Control
Control Panel
1
If necessary, press the
Result:
POWER
(On/Off) button.
◆ The operating mode indicator (COOL, HEAT or FAN)
on the unit comes on.
◆ The air conditioner starts up in the mode selected
when the unit was last used.
◆ The unit beeps twice.
air conditioner is fitted with a protection mechanism to prevent
☛ The
the unit from being damaged when it is started immediately after
being:
◆ Plugged in
◆ Stopped
It will start up automatically after a three-minute rest period.
2
RESTART
COOL
FAN
If the COOL indicator is not lit up on the unit:
◆ Press the
button on the remote control
or
◆ Press the MODE button on the unit one or more times until the COOL
indicator lights up
Result:
MODE
POWER
➢
3
Hr.
◆ The unit beeps each time you press MODE.
◆ The air conditioner starts up in Cool mode.
You can change modes at any time.
To adjust the temperature, press the
or
buttons on the remote
control one or more times until the required temperature is displayed.
To adjust the temperature, press the TEMPERATURE button on the unit
one or more times until the required temperature is displayed.
◆ 24°C --> 25°C --> .... --> 29°C --> 30°C --> 18°C --> 19°C --> ....
Possible temperatures are between 18°C and 30°C inclusive.
C
Result:
TEMP.
4
◆ Each time you press the temperature buttons:
– The temperature is adjusted by 1°C and
displayed on the control panel
– The unit beeps
◆ The air conditioner starts cooling if the room temperature
is higher than the selected temperature.
To set the fan speed to...
Then...
High
Press the
button on the remote control.
Low
Press the
button on the remote control.
HIGH
LOW
FAN SPEED
Result:
5
E-8
Each time you press a button, the unit beeps.
To control the direction of the air flow, refer to page 11.
ENGLISH
Heating Your Room
You must select the Heat mode if you wish to heat your room to a
specific temperature. You can also set the fan speed.
1
If necessary, press the
Result:
Remote Control
(On/Off) button.
Control Panel
◆ The operating mode indicator (COOL, HEAT or FAN)
on the unit comes on.
◆ The air conditioner starts up in the mode selected
when the unit was last used.
◆ The unit beeps twice.
POWER
air conditioner is fitted with a protection mechanism to prevent
☛ The
the unit from being damaged when it is started immediately after
being:
◆ Plugged in
◆ Stopped
It will start up automatically after a three-minute rest period.
2
If the HEAT indicator is not lit up on the unit:
◆ Press the
button on the remote control
or
◆ Press the MODE button on the unit one or more times until the HEAT
indicator lights up
Result:
➢
3
COOL
◆ The unit beeps each time you press MODE.
◆ The air conditioner starts up in Heat mode.
FAN
MODE
POWER
You can change modes at any time.
To adjust the temperature, press the
or
buttons on the remote
control one or more times until the required temperature is displayed.
To adjust the temperature, press the TEMPERATURE button on the unit
one or more times until the required temperature is displayed.
◆ 24°C --> 25°C --> .... --> 29°C --> 30°C --> 16°C --> 17°C --> ....
Possible temperatures are between 16°C and 30°C inclusive.
Result:
4
RESTART
Hr.
C
◆ Each time you press the temperature buttons:
– The temperature is adjusted by 1°C and
displayed on the control panel
– The unit beeps
◆ The air conditioner starts heating if the room temperature
is lower than the selected temperature.
To set the fan speed to...
Then...
High
Press the
button on the remote control.
Low
Press the
button on the remote control.
TEMP.
HIGH
LOW
Result:
5
◆ Each time you press a button, the unit beeps.
◆ For the first three to five minutes, the fan operates very
slowly until the air has been sufficiently warmed.
Once the correct temperature has been reached, the
fan is automatically set to the required speed.
FAN SPEED
To control the direction of the air flow, refer to page 11.
E-9
Airing Your Room
If the atmosphere in your room is stale, you can air it using the Fan
feature and if necessary, evacuate the stale air outside.
1
Hr.
C
If you wish to evacuate stale air outside, pull the ventilation lever on the
front of the unit and the open position (
).
Result:
FAN SPEED
The air inside the room circulates and stale air is evacuated
outside.
Otherwise, push the ventilation lever and the closed position (
Result:
Open
Position
).
The air simply circulates inside the room.
Closed
Position
Remote Control
Control Panel
2
If necessary, press the
Result:
POWER
3
RESTART
COOL
FAN
POWER
➢
4
◆ The operating mode indicator (COOL, HEAT, or FAN)
on the unit comes on.
◆ The air conditioner starts up in the mode selected
when the unit was last used.
◆ The unit beeps twice.
If the FAN indicator is not lit up on the unit:
◆ Press the
button on the remote control
or
◆ Press the MODE button on the unit one or more times until the FAN
indicator lights up
Result:
MODE
(On/Off) button.
◆
◆
◆ The unit beeps each time you press MODE.
◆ The air conditioner starts up in Fan mode.
You can change modes at any time.
When the air conditioner is in Fan mode, the
temperature is not displayed; in this case, you do not
need to set the temperature.
To set the fan speed to...
Then...
High
Press the
button on the remote control.
Low
Press the
button on the remote control.
HIGH
LOW
FAN SPEED
Result:
5
E-10
Each time you press a button, the unit beeps.
To control the direction of the air flow, refer to page 11.
ENGLISH
Adjusting the Air Flow Direction Horizontally
Depending on the position of the unit in your room, you can adjust the
orientation of the inner air flow blades on the right-hand side of the
unit, thus increasing the efficiency of the air conditioner.
Remote Control
1
Press the
Result:
➢
(or
Control Panel
on the unit) button on the remote control.
The inner blades swing automatically left and right.
The blades may stop swinging momentarily when the Deice function is
activated(see page 14 for further details on this function). They will start
swinging again automatically as soon as the Deice function stops.
SWING
COOL
2
To stop the blades moving left and right, press the
button on the remote control.
➢
(or
FAN
on the unit)
To stop the blades in a specific position and orient the air flow in the
corresponding direction, simply press the
(or
on the unit)
button on the remote control when the blades are in the desired position.
Adjusting the Air Flow Direction Vertically
Again depending on the position of the unit in your room, you can
adjust the orientation of the outer air flow blades on the right-hand
side of the unit.
RECOMMENDATION
When...
Adjust the blades to face...
Cooling
Upwards.
Heating
Downwards.
Adjust the air flow blades to the desired position, by pushing them upwards or
downwards.
➢
If you orient the air flow blades downwards and the unit operates in Cool mode
for a long period of time, dew may:
◆ Form on the surface of the blades
◆ Drip from the blades
E-11
Switching the Unit Off Automatically (Off Timer)
You can set the timer to switch the air conditioner off automatically
at a given time.
Example:
Remote Control
Control Panel
You wish to switch the unit off two hours after you
have gone to bed.
1
If necessary, press the
2
Select the required mode by pressing the appropriate button:
(On/Off) button.
POWER
◆
◆
RESTART
COOL
FAN
,
or
on the remote control
MODE button on the unit (press it one or more times until the
appropriate operating mode indicator lights up)
MODE
POWER
3
Hr.
Set the operating time by pressing:
◆ TIMER ▲ or ▼ on the remote control one or more times.
C
Example: To switch the unit off two hours after you have gone to bed, set
the operating time to 2 hours.
Possible operating times are between 1 and 24 hours inclusive.
Result:
➢
◆ The Hr indicator flashes for about ten seconds.
◆ The operating time is displayed and decreased
automatically to indicate the remaining time.
◆ The air conditioner switches off automatically when
the operating time reaches zero.
You can change your setting at any time.
Canceling the Off Timer
If you no longer wish to use the Off Timer that you have set, you can
cancel it at any time.
Remote Control
Control Panel
Hr.
E-12
C
To cancel the timer, press:
◆ TIMER ▲ or ▼ on the remote control one or more times until “- -” is displayed.
Result:
◆ The unit beeps each time you press a button.
◆ The Hr indicator on the unit switches off.
◆ The air conditioner operates automatically.
ENGLISH
Operating Recommendation
Here are a few recommendations that you should follow when using
your air conditioner.
Topic
Recommendation
Heating performances
The heat pump inside the air conditioner absorbs
heat from outside air and brings it indoors. If the
temperature of the outside air drops, the air
conditioner will heat less. If you find that the room is
not warm enough, use an additional heating
appliance.
Warm air circulation
The air conditioner circulates warm air to heat your
room; as a result, some time will be required after
starting the air conditioner to warm the entire room.
If necessary, set the air conditioner going a short
time before you wish to use the room.
Frost
When outside temperatures are low and humidity is
high, frost may form in the unit’s condensor when
heating with your air conditioner.
If this happens:
◆ The unit stops heating
◆ The air flow blades stop swinging
◆ The Deice mode is triggered automatically for
about five minutes
◆ The DEICE indicator on the unit lights up red
No intervention is required from you; after about five
minutes, the air conditioner starts operating again
normally.
High indoor and outdoor temperatures
If both the indoor and outdoor temperatures are
high and you select the Heat mode, the fan and
compressor in the unit may stop at times. This is
normal; simply wait until the air conditioner switches
on again.
Power failure
If a power failure occurs when the air conditioner is
operating, the unit is switched off.
When the power returns,
AZ09F7KE
AZ09A7KE
you must press
(On/Off)
button to restart it.
AZ09F8KE
AZ09A8KE
the air conditioner starts
up again automatically and
the restart indicator blinkes
for 2 minutes and then
lights up.
E-13
Temperature and Humidity Ranges
The following table indicates the temperature and humidity ranges within which the air
conditioner can be used.
E-14
Mode
Indoor Temperature
Outdoor Temperature
Indoor Humidity
Cooling
Heating
21°C to 32°C approx.
28°C or less
21°C to 43°C approx.
0°C to 21°C approx.
80% or less
-
If the air conditioner is used at...
Then...
Higher temperatures
The automatic protection feature may be triggered and the air
conditioner stopped.
Lower temperatures
A water leakage or some other malfunction may happen if the
heat exchanger freezes.
Higher humidity levels
Water may condense on and drip from the surface of the unit if
it is used for long periods.
ENGLISH
Cleaning Your Air Conditioner (✴✴✴✴F7/F8✴✴ models)
Be sure to clean the air filter periodically to maintain the air conditioner
in the best condition for a long period of time.
☛
1
When cleaning the air conditioner, turn it off and pull out the
power plug.
Hold the air filter handle, slightly pull it to the left side and open the front grille.
➢
The removal of the front grille makes it easier to clean the air
conditioner. Open the grille as much as possible.
CAUTION
Hr.
C
FAN SPEED
Removal and Reassembly of the Front Grille
For user's safety, a safety clip has been installed in the front grille.
1 Grasp the lower part of the
front grille and the air filter
handle, then open the grille.
Safety clip
2 Remove the safety clip and
the front grille.
3 When reassembling the front
grille, you should install the
safety clip again.
Hr.
C
FAN SPEED
2
Pull the air filter to the right side.
3
Remove all dust on the air filter with a vacuum cleaner or brush.
4
When you have finished, insert the air filter back into its original position.
5
Wipe the surface of the unit with a neutral detergent and then wipe it again
with dry cloth.
(Be sure not to use benzene, solvent or other chemical products.)
Hr.
C
FAN SPEED
➢
If you...
Then...
Will not be using the
air conditioner for a
long period of time
◆ Set the fan going for a few hours to
dry the inside of the air conditioner
thoroughly.
◆ Switch the air conditioner off and
unplug it from the wall socket.
◆ Clean the filter and outer surfaces.
Have not used the air
conditioner for a long
period of time
Set the fan going for a few hours to dry
the inside of the air conditioner
thoroughly.
E-15
Cleaning Your Air Conditioner (✴✴✴✴A7/A8✴✴ models)
Be sure to clean the air filter periodically to maintain the air conditioner
in the best condition for a long period of time.
☛
1
When cleaning the air conditioner, turn it off and pull out the
power plug.
Open the front grille by pulling on the tabs of the unit.
➢
The removal of the front grille makes it easier to clean the air
conditioner. After opening the front grille, lift it up as much as possible,
then pull down to release it.
Hr.
C
TEMP
HIGH
LOW
RESTART
COOL
SWING
FAN
FAN SPEED
POWER
MODE
2
Grasp the handle on the air filter and lift it slightly and then out to the front.
3
Remove all dust on the air filter with a vacuum cleaner or brush.
4
When you have finished, insert the air filter back into its original position.
5
Wipe the surface of the unit with a neutral detergent
and then wipe it again with dry cloth.
(Be sure not to use benzene, solvent or other chemical products.)
Front grille
Front grille
Grille groove
Body guide
E-16
➢
If you...
Then...
Will not be using the
air conditioner for a
long period of time
◆ Set the fan to “FAN” and let it for a few
hours to dry the inside of the air
conditioner thoroughly.
◆ Switch the air conditioner off and
unplug it from the wall socket.
◆ Clean the filter and outer surfaces.
Have not used the air
conditioner for a long
period of time
Set the fan to “FAN” and let it run for
a few hours to dry the inside of the air
conditioner thoroughly.
ENGLISH
Solving Common Problems
Before contacting the after-sales service, perform the following simple checks.
They may save you the time and expense of an unnecessary service call.
Problem
Explanation/Solution
◆ Check that the circuit breaker used for the air conditioner has not
The air conditioner does not
operate at all
been triggered.
◆ Check that the power cable is plugged into a wall socket and
the socket is switched on, if necessary.
◆ Check that the operating mode indicator (COOL, HEAT or FAN)
on the unit is lit up; if necessary press
the remote control or unit.
(On/Off) on
The air conditioner does not
operate with the remote control
◆ Check that there are no obstacles between you and the unit.
◆ Replace the remote control batteries if necessary.
◆ Check that you are close enough to the unit (seven metres/yards or less).
No beep is heard when you press
(On/Off) on the remote control
◆ Check that you are pointing the remote control at the remote control
sensor on the unit.
◆ Replace the remote control batteries if necessary.
The air conditioner does not
cool or heat
◆ Check that the correct operating mode has been selected COOL
or HEAT.
◆ The room temperature may be too low or too high.
◆ Dust may be blocking the air filter; refer to page 15 or 16 for
cleaning instructions.
◆ Check that there is no obstacle blocking the air flow into or
out of the unit.
When heating, the required room
◆ Check that the required temperature has been set correctly.
temperature is never reached and ◆ Increase the fan speed.
the air conditioner frequently stops ◆ If the air flow is directed downwards, direct it upwards.
The air flow direction does not
change when you press the
(or
on the unit)button
◆ Check that the air conditioner has been switched on; if necessary,
press
(On/Off) on the remote control or unit.
The timer is not correctly triggered ◆ Check that the timer has been programmed correctly; see page 12.
Odours are permeated in the
room during air conditioning
◆ Air the room.
Technical Specifications
Design and specifications are subject to change without notice.
Model
Power Supply
AZ09F7KE
AZ09A7KE
AZ09F8KE
AZ09A8KE
220-240V~, 50Hz
E-17
Method of Installation
Before installation, be sure to check the installation area or the air
conditioner, and drain hose.
Checkpoints prior to installation
1 Check the cabinet and front grille of the unit for any harmful defects
such as scratches.
2 Be sure to check the power supply.
- Refer to the specifications on the label attached to the unit.
Installation Conditions
1 As the unit is heavy, the wall or window of the installation area should
have sufficient strength and durability for operation of the air conditioner,
and for prevention of any vibration or noise.
If it is weak, reinforcement work should be performed separately.
2 It is advisable to install the air conditioner in the north or west side to
prevent the effect of direct sunlight.
When installing it in the south or east side due to unavoidable
circumstances, it is advisable to install the sunshade to prevent the
direct sunlight.
In this case, take care not to cause any hindrance to the flow of outside air.
3 When installing the air conditioner, be sure to obtain sufficient space on
the rear side of the unit for smooth flow of air.
When operating the air conditioner in closed areas such as inner building
with cooling operation, and result in trouble with the unit.
See the illustration below.
Awning
75mm
min.
300mm
200mm
500mm
500mm
500mm
Fence, wall
or other
obstacle
Approx.3˚
750mm
➢
150mm min.
◆ If the wall is greater than 150mm thick,
cut the wall back on a 45˚ angle if possible.
Outdoor Side
Indoor Side
100mm or more
E-18
45˚
45˚
ENGLISH
Installation of the Drain Tube
Rear
Fix the drain tube as shown in the figure.
Rubber cap
Gasket
Drain Tube
Screws(2EA)
Installation of the Drain Pan
The procedure for installing the drain pan should be determined by the
condition of the installing area.
◆ In the case of an area where the drain pan can not be directly
installed on the rear side of the unit after installing the air conditioner.
Example: High storage
1
Open the front grille; refer to page 15 or 16.
2
Remove the screw located at the lower section of the front grille.
It is secured in the
section depending on the model.
3
Remove the front panel.
3-1 Press both sides of the cabinet in the direction of the arrow
as shown in the figure.
Hr.
C
FAN SPEED
Front panel
Screw
3-2 Pull the lower part of the front panel slightly forward.
(below three inches)
3-3 Lift the front panel upward.
☛
Applying excessive force to remove the front panel
may cause damage to the tab ; be sure not to use
excessive force.
4
Remove two screws on the lower, right and left sides of the unit.
5
Remove the chassis from the cabinet.
6
Remove the rubber cap inserted into the basepan.
Screw
Rear
7
Fix the drain pan as shown in the figure, and then connect the drain hose.
(You can use any commercially-available drain hose.)
8
Install the cabinet at the specified area after installing the drain pan,
and then re-assemble it in the original condition.
Rubber cap
Drain Pan
Drain Hose
Bottom-Side View with
Drain Pan and Hose in Place
◆ In the case of an area where the drain pan can be directly installed
on the rear side of the unit after installing the air conditioner.
1
Follow steps 6 and 7 only
E-19
THIS AIR CONDITIONER IS MANUFACTURED BY:
CE CLIMATISEUR EST FABRIQUE PAR:
ELECTRONICS
Printed in Korea