HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 2
DIGITAL HOME
CINEMA SYSTEM
THIS APPLIANCE IS MANUFACTURED BY:
HT-WQ20
HT-TWQ22
HT-TWQ25
Instruction Manual
COMPACT
AH68-01887B
DIGITAL AUDIO
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 4
Safety Warnings
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE REAR COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CLASS 1 LASER PRODUCT
GB
Use of controls, adjustments or performance of procedures other
than those specified herein may result in hazardous radiation
exposure.
PREPARATION
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
Precautions
CAUTION-INVISIBLE LASER RADIATION WHEN OPEN
AND INTERLOCKS DEFEATED, AVOID EXPOSURE TO BEAM.
This symbol indicates that dangerous voltage which
can cause electric shock is present inside this unit.
This symbol alerts you to important operating and
maintenance instructions accompanying the unit.
WARNING: To reduce the risk of fire or electric shock, do not
expose this appliance to rain or moisture.
Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install your
player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). Make sure the ventilation
slots are not covered. Do not stack anything on top of the player. Do not place the player on amplifiers or other equipment which may
become hot. Before moving the player, ensure the disc tray is empty. This player is designed for continuous use. Switching off the DVD
player to the stand-by mode does not disconnect the electrical supply. In order to disconnect the player completely from the power supply, remove the main plug from the wall outlet, especially when left unused for a long period of time.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
This Compact Disc player is classified as a CLASS 1 LASER product.
• This apparatus shall always be connected to a AC outlet with a protective grounding connection.
• To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.
Wiring the Main Power Supply Plug(UK Only)
IMPORTANT NOTICE
The main lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin
face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be used.
Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of the same
colour as the fuse fitted in the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you
should obtain a suitable safety approved extension lead or consult your dealer for assistance.
However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the
plug to a main socket as there is a risk of shock hazard from the bared flexible cord.
Never attempt to insert bare wires directly into a main socket. A plug and fuse must be used at all times.
During thunderstorms, disconnect AC main plug from the
wall outlet.
Voltage peaks due to lightning could damage the unit.
Do not expose the unit to direct sunlight or other heat
sources.
This could lead to overheating and malfunction of the unit.
Phones
IMPORTANT
The wires in the main lead are coloured in accordance with the following code:–
BLUE = NEUTRAL
BROWN = LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:–
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK.
The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH
THE LETTER E OR BY THE EARTH SYMBOL
, OR COLOURED GREEN OR GREEN
AND YELLOW.
1
Protect the player from moisture(i.e. vases) , and excess heat
(e.g.fireplace) or equipment creating strong magnetic or electric fields
(i.e.speakers...). Disconnect the power cable from the AC supply if the
player malfunctions. Your player is not intended for industrial use.
Use of this product is for personal use only.
Condensation may occur if your player or disc has been stored in cold
temperatures.
If transporting the player during the winter, wait approximately 2 hours
until the unit has reached room temperature before using.
The batteries used with this product contain chemicals
that are harmful to the environment.
Do not dispose of batteries in the general household
trash.
2
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 6
Features
Contents
GB
Multi-Disc Playback & FM Tuner
USB HOST Function support
You can connect and play files from external USB storage devices such as
MP3 players, USB flash memory, etc. using the Home Theater's USB HOST function.
PREPARATION
SETUP
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Setting the Language . . . . . . . . . . . . . . . . . . . . . . .41
Setting TV Screen type . . . . . . . . . . . . . . . . . . . . . .43
Setting Parental Controls (Rating Level) . . . . . . . . .45
Setting the Password . . . . . . . . . . . . . . . . . . . . . . .46
Setting the Wallpaper . . . . . . . . . . . . . . . . . . . . . . .47
DivX (R) registration . . . . . . . . . . . . . . . . . . . . . . . .49
Setting the Speaker Mode . . . . . . . . . . . . . . . . . . .50
Setting the Delay Time . . . . . . . . . . . . . . . . . . . . . .51
Setting the Test Tone . . . . . . . . . . . . . . . . . . . . . . .53
Setting the DRC (Dynamic Range Compression) . .54
Setting the Audio Quality . . . . . . . . . . . . . . . . . . . . .55
AV SYNC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Sound Field (DSP)/EQ Function . . . . . . . . . . . . . . .58
Dolby Pro Logic II Mode . . . . . . . . . . . . . . . . . . . . .59
Dolby Pro Logic II Effect . . . . . . . . . . . . . . . . . . . . .60
CONNECTIONS
Dolby Pro Logic II
Dolby Pro Logic II is a new form of multi-channel audio signal decoding technology
that improves upon existing Dolby Pro Logic.
Connecting the Speakers . . . . . . . . . . . . . . . . . . . .11
Connecting the optional Wireless Receiving Amplifier 14
Connecting the Video Out to TV . . . . . . . . . . . . . . .16
P.SCAN(Progressive Scan) Function . . . . . . . . . . . .17
Connecting External Components . . . . . . . . . . . . . .18
Connecting the FM Antenna . . . . . . . . . . . . . . . . . .19
DTS (Digital Theater Systems)
DTS is an audio compression format developed by Digital Theater
Systems Inc. It delivers full-frequency 5.1 channel sound.
TV Screen Saver Function
The HT-WQ20/HT-TWQ22/HT-TWQ25 automatically brightens and darkens your TV
screen after 3 minutes in the stop mode.
The HT-WQ20/HT-TWQ22/HT-TWQ25 automatically switches itself into the power
saving mode after 20 minutes in the screen saver mode.
Power Saving Function
The HT-WQ20/HT-TWQ22/HT-TWQ25 automatically shuts itself off after 20 minutes in stop
mode.
Customized TV Screen Display
The HT-WQ20/HT-TWQ22/HT-TWQ25 allows you to select your favorite image during
JPEG, DVD or VCD playback and set it as your background wallpaper.
Optional Wireless receiver amplifier
Samsung ’s optional rear-channel wireless module does away with cables running between
your DVD receiver and rear-channel speakers. Instead,the rear speakers connect to a compact wireless module that communicates with your DVD receiver.
3
OPERATION
Before Using Your Home Theater . . . . . . . . . . . . . .20
Disc Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
MP3/WMA-CD Playback . . . . . . . . . . . . . . . . . . . . .23
Displaying Disc Information . . . . . . . . . . . . . . . . . . .24
JPEG File Playback . . . . . . . . . . . . . . . . . . . . . . . .25
DivX Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Checking the Remaining Time . . . . . . . . . . . . . . . .29
Fast/Slow Playback . . . . . . . . . . . . . . . . . . . . . . . .30
Skipping Scenes/Songs . . . . . . . . . . . . . . . . . . . . .30
Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . .31
A-B Repeat Playback . . . . . . . . . . . . . . . . . . . . . . .32
Step Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Angle Function . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Zoom (Screen Enlarge) Function . . . . . . . . . . . . . .34
EZ VIEW Function . . . . . . . . . . . . . . . . . . . . . . . . .34
Selecting Audio Language . . . . . . . . . . . . . . . . . . .35
Selecting Subtitle Language . . . . . . . . . . . . . . . . . .36
Playing Media Files using the USB HOST feature . .37
Moving Directly to a Scene/Song . . . . . . . . . . . . . .39
Using Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . .40
Using the Title Menu . . . . . . . . . . . . . . . . . . . . . . . .40
PREPARATION
The HT-WQ20/HT-TWQ22/HT-TWQ25 combines the convenience of multi-disc playback
capability, including DVD-VIDEO, VCD, CD, MP3-CD, WMA-CD, DivX, CD-R/RW, and DVDR/RW, with a sophisticated FM tuner, all in a single player.
RADIO OPERATION
Listening to Radio . . . . . . . . . . . . . . . . . . . . . . . . . .61
Presetting Stations . . . . . . . . . . . . . . . . . . . . . . . . .62
About RDS broadcasting . . . . . . . . . . . . . . . . . . . .63
MISCELLANEOUS
Convenient Functions . . . . . . . . . . . . . . . . . . . . . . .65
Operating a TV with the Remote Control . . . . . . . . .67
Before Calling for Service . . . . . . . . . . . . . . . . . . . .68
Cautions on Handling and Storing Discs . . . . . . . . .71
Language Code List . . . . . . . . . . . . . . . . . . . . . . . .72
USB Host Feature Supported Products . . . . . . . . . .73
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
4
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 8
Notes on Discs
GB
DVD (Digital Versatile Disc) offers fantastic audio and video, thanks to Dolby Digital sur-
1
~ 6
DVD players and the discs are coded by region. These regional codes must match in order
for the disc to play. If the codes do not match, the disc will not play.
The Region Number for this player is given on the rear panel of the player.
(Your DVD player will only play DVDs that are labeled with identical region codes.)
Mark (Logo)
Recorded Signals
Disc Size
12cm
8cm
AUDIO-CD
COMPACT
VIDEO-CD
DIGITAL AUDIO
Divx
Max. Playing Time
Approx. 240 min. (single-sided)
Approx. 480 min. (double-sided)
Approx. 80 min. (single-sided)
Approx. 160 min. (double-sided)
Audio
12cm
74 min.
Audio + Video
8cm
20 min.
MPEG4
MP3
12cm
74 min.
8cm
20 min.
• LD, CD-G, CD-I, CD-ROM and DVD-ROM discs cannot be played on this player.
If such discs are played, a "WRONG DISC FORMAT" message appears on the TV screen.
• DVD discs purchased abroad may not play on this player.
If such discs are played, a "WRONG REGION CODE" message appears on the TV screen.
Copy Protection
• Many DVD discs are encoded with copy protection. Because of this, you should only connect
5
• Some CD-R discs may not be playable depending on the disc recording device (CD-Recorder or PC) and the condition of the disc.
• Use a 650MB/74 minute CD-R disc.
Do not use CD-R discs over 700MB/80 minute as they may not be played back.
Do not use the following types of disc!
•
CD-R Discs
not be able to fully play the disc.
Video
DVD-VIDEO
This product does not support Secure (DRM) Media files.
• Some CD-RW (Rewritable) media, may not be playable.
• Only CD-Rs that are properly "closed" can be fully played. If the session is closed but the disc is left open, you may
Playable Discs
Disc Type
Disc Recording Format
your DVD player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected DVD discs.
This product incorporates copyright protection technology that is protected by methods claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
CD-R MP3 Discs
• Only CD-R discs with MP3 files in ISO 9660 or Joliet format can be played.
• MP3 file names should be 8 characters or less in length and contain no blank spaces or special characters (. / = +).
• Use discs recorded with a compression/decompression data rate greater than 128Kbps.
• Only files with the ".mp3" and ".MP3" extensions can be played.
• Only a consecutively written Multisession disc can be played. If there is a blank segment in the Multisession disc,
the disc can be played only up to the blank segment.
• If the disc is not closed, it will take longer to begin playback and not all of the recorded files may be played.
• For files encoded in Variable Bit Rate (VBR) format, i.e. files encoded in both low bit rate and high bit rate
(e.g., 32Kbps ~ 320Kbps), the sound may skip during playback.
• A maximum of 500 tracks can be played per CD.
• A maximum of 300 folders can be played per CD.
CD-R JPEG Discs
• Only files with the ".jpeg" and ".JPEG" extensions can be played.
• If the disc is not closed, it will take longer to start playing and not all of the recorded files may be played.
• Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played.
• JPEG file names should be 8 characters or less in length and contain no blank spaces or special characters (. / = +).
• Only a consecutively written multisession disc can be played. If there is a blank segment in the multisession disc,
the disc can be played only up to the blank segment.
• A maximum of 9,999 images can be stored on a single CD.
• When playing a Kodak/Fuji Picture CD, only the JPEG files in the picture folder can be played.
• Picture discs other than Kodak/Fuji Picture CDs may take longer to start playing or may not play at all.
CD-R/RW DivX Discs
• Since this product only provides encoding formats authorized by DivX Networks, Inc., a DivX file created by the
user might not be played.
• Software update for unsupported formats is not supported.
(Example: QPEL, GMC, resolution higher than 720 x 480 pixels, etc.)
• Sections with high frame rate might not be played while playing a DivX file.
• For more information about the formats authorized by DivX Networks, Inc., visit "www.divxnetworks.net".
6
PREPARATION
round sound and MPEG-2 video compression technology. Now you can enjoy these realistic
effects in the home, as if you were in a movie theater or concert hall.
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 10
Description
GB
—Rear Panel—
Stop (
Disc Tray
COMPONENT VIDEO OUTPUT jacks
) button
Play/Pause (
Open/Close button
Remote
Control Sensor
Cooling Fan
USB Connector
Tuning Up & Skip (
) buttons
Tuning Down & Skip (
) buttons
Connect a TV with component video inputs to
these jacks.
Connect the TV's video input jacks (VIDEO IN)
to the VIDEO OUT connector.
Volume buttons
Function button
Standby indicator
Power (
Video Output Connector
) button
5.1 Channel Speaker
Output Terminals
External Audio Input
Connector
FM Antenna Connector
SCART JACK
Connect to a TV with scart input jack.
TX Card Connector
) button
Accessories
P.SCAN indicator
DOLBY DIGITAL indicator
DTS Disc indicator
REPEAT indicator
LINEAR PCM indicator
TITLE indicator
PBC indicator
Remote Control
Video Cable
FM Antenna
User's Manual
TUNER indicator
CHAPTER indicator
TRACK indicator
PROGRAM indicator
STEREO indicator
SWA-3000
RTA indicator
RDS indicator
DSP indicator
MPEG indicator
PRO LOGIC indicator
7
System Status Display
RADIO FREQUENCY
indicator
SPEAKER indicator
Wireless Receiver Module
TX Card
Speaker Cable (2EA)
8
PREPARATION
—Front Panel—
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 12
Description
GB
PREPARATION
—Remote Control—
Insert Remote Batteries
TV button
DVD RECEIVER button
DVD button
TUNER button
AUX button
USB button
OPEN/CLOSE button
POWER button
cover on the back of
the remote by pressing
down and sliding the
cover in the direction of
the arrow.
TV/VIDEO button
RDS Selection button
Number(0~9) buttons
REMAIN button
STEP button
SEARCH buttons
1 Remove the battery
VIDEO.SEL button
2
Insert two 1.5V AAA
batteries, paying attention to the correct
polarities (+ and –).
3
Replace the battery
cover.
CANCEL button
REPEAT button
Play/Pause button
Stop button
Tuning Preset/CD Skip button
VOLUME button
TUNING/CH button
Caution
MENU button
MUTE button
RETURN button
Cursor/Enter button
INFO button
PL II EFFECT button
PL II MODE button
TUNER MEMORY, P.SCAN button
ZOOM button
SLEEP button
SLOW, MO/ST button
DIMMER button
9
AUDIO button
SUB TITLE button
DSP/EQ button
TEST TONE button
SOUND EDIT button
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity:(+) to (+)and (–)to (–).
• Use the correct type of batteries.Batteries that look similar may differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
Range of Operation of the Remote Control
The remote control can be used up to approximately 23 feet/7 meters in a straight line. It can also
be operated at a horizontal angle of up to 30° from the remote control sensor.
DIGEST button
VOLUME
OPEN/CLOSE
LOGO button
FUNCTION
STANDBY
SLIDE MODE button
EZ VIEW, NT/PAL button
10
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 14
Connecting the Speakers
GB
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
HT-WQ20
Center Speaker
C
Front Speaker (R)
SW
L
Front Speaker (L)
R
CONNECTIONS
SL
SR
Rear Speaker (R)
Rear Speaker (L)
Subwoofer
Position of the DVD Player
• Place it on a stand or cabinet shelf, or under
the TV stand.
Connecting the Speakers
Selecting the Listening Position
The listening position should be located about 2.5 to 3
times the distance of the TV's screen size away from the
TV. Example: For 32" TVs 2~2.4m (6~8feet)
For 55" TVs 3.5~4m (11~13feet)
1
Press down the terminal
tab on the back of the
speaker.
Front Speakers L R
• Place these speakers in front of your listening position, facing inwards (about 45°) toward you.
• Place the speakers so that their tweeters will be at
the same height as your ear.
• Align the front face of the front speakers with the
front face of the center speaker or place them
slightly in front of the center speakers.
speakers.
• You can also install it directly over or under the TV.
Insert the black wire into the
black terminal (–) and the red
wire into the red (+) terminal,
and then release the tab.
Black
Rear Speakers SL SR
• Place these speakers behind your listening position.
• If there isn't enough room, place these speakers so they face each other.
• Place them about 60 to 90cm (2 to 3feet) above your ear, facing slightly
3
Connect the correct color speaker cable
to the same color speaker output terminal
on the rear of the subwoofer, according
to the polarity markings (+/–).
Example: Connect the green center speaker cable
to the green center speaker output terminal on the rear of the subwoofer according to the polarity markings (+/–).
Red
downward.
Unlike the front and center speakers, the rear speakers are used to
* handle
mainly sound effects and sound will not come from them all
Center Speaker C
• It is best to install it at the same height as the front
2
the time.
Subwoofer SW
• The position of the subwoofer is not so critical.
Caution
• Do not let children play with or near the speakers.
They could get hurt if a speaker falls.
• When connecting the speaker wires to the speakers,
make sure that the polarity (+/–) is correct.
Note
• If you place a speaker near your TV set,
screen color may be distorted because of
the magnetic field generated by the speaker. If this occurs, place the speaker away
from your TV set.
Place it anywhere you like.
11
12
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 16
Connecting the Speakers
Connecting the Wireless Receiving Amplifier
GB
HT-TWQ22
Center Speaker
Front Speaker (R)
Front Speaker (L)
CONNECTIONS
Rear Speaker (R)
Rear Speaker (L)
Subwoofer
HT-TWQ25
Rear Speaker (L)
1
Connect the front, center and
subwoofer speakers, referring to page 12.
2
Insert the TX card into the TX card
connection port on the back of the main unit.
Rear Speaker (R)
• Hold the TX card so that the slanted side faces down-
Center Speaker
Front Speaker (R)
WIRELESS RECEIVER MODULE
ward and insert the card into the port.
• The TX card enables communication between the
Front Speaker (L)
main unit and the wireless receiver.
TX card
Slanted side faces
3
Connect the left and right rear
speakers to the wireless receiving
module.
4
Plug the power cord of the wireless
receiving module in the wall outlet and
switch the power switch ‘ON’.
Rear Speaker (L)
Rear Speaker (R)
Caution
Subwoofer
13
• Do not insert a card other than the TX card dedicated for the product. The product might be damaged or it may not be removed easily.
• Do not insert the TX card upside down or in reverse direction.
• Insert the TX card when the main unit is turned off.Inserting the card when it is turned on may cause a problem.
• If the TX Card is inserted in the main unit, the rear speakers don't output sounds.
14
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 18
Connecting the Wireless Receiving Amplifier
Connecting the Video Out to TV
GB
Choose one of the three methods for connecting to a TV.
Resetting Wireless Communication
Reset the system if a communication failure occurs, or if the Link indicator (blue LED) on the wireless receiver does
not light up and the "REAR CHK" message blinks on the main unit's display.
Reset the system while the main unit and the wireless receiver module (SWA-3000) are in Power Standby mode.
1
METHOD 1
METHOD 2
METHOD 3
CONNECTIONS
With the main unit turned off, press and
hold the remote control's REMAIN button
for 5 seconds.
• Press the button until the POWER(
) indicator lights
up blue. (The indicator will turn off in 1 second.)
2
With the wireless receiver module
turned on, use a ball point pen or a pair
of tweezers to press the RESET button
on the back of the unit.
WIRELESS RECEIVER MODULE
• The Standby/On LED on the front panel of the
wireless receiver module blinks 2 times.
3
Turn on the main unit.
• The Link LED of the wireless receiver module is lit
•
and the setup is finished.
If Power Standby mode continues, repeat Steps 1 to
3 above.
Caution
• When the wireless receiving module setting is complete, no audio signal is output from the Rear Speaker OUT ports on the back
of the main unit.
• The wireless receiving antenna is built into the wireless receiver module. Keep the unit away from water and moisture.
• For optimal listening performance, make sure that the area around the wireless receiver module location is clear of any obstruc•
•
tions.
Sound will be heard from the wireless rear speakers in DVD 5.1-CH or Dolby Pro Logic II mode only.
In 2-CH mode, no sound will be heard from the wireless rear speakers.
METHOD 1 Composite Video ............... Good Quality
Connect the supplied video cable from the VIDEO OUT jack on the back panel of the system to the VIDEO IN jack on your television.
METHOD 2 Scart ............... Better Quality
If you television is equipped with an SCART input, connect an Scart Jack (not supplied) from the
AV OUT jack on the back panel of the system to the SCART IN jack on your television.
VIDEO SELECT Function
Press and hold VIDEO SEL. button on the remote control for over 5 seconds.
• "COMPOSITE" or "RGB" will appear in the display.
At this time, press the VIDEO SEL. button shortly to select between "COMPOSITE" and "RGB".
• If Scart (RGB Input) is equipped for your TV, press VIDEO SEL. button to select RGB mode.
You can get a better picture quality by using Scart setting.
• If Scart (RGB Input) is not equipped for your TV, press VIDEO SEL. button to select COMPOSITE
mode.
Note
•
•
•
15
Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too close to the main
unit, some sound interruption may be heard due to interference.
If you use a device such as a microwave oven, wireless LAN Card, Bluetooth equipment, or any other device that uses the same
frequency (2.4GHz) near the system, some sound interruption may be heard due to interference.
The transmission distance of radio wave is about 33 feet, but may vary depending on your operating environment.
If a steel-concrete wall or metallic wall is between the main unit and the wireless receiver module, the system may not operate at
all, because the radio wave cannot penetrate metal.
METHOD 3 Component (Progressive Scan) Video ............... Best Quality
If your television is equipped with Component Video inputs, connect a component video
cable (not supplied) from the Pr, Pb and Y jacks on the back panel of the system to the corresponding jacks on your television.
Note
• When the Progressive scan mode is selected, the VIDEO output (Yellow) and
SCART output does not output any signal.
16
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 20
P.SCAN(Progressive Scan) Function
Connecting External Components
GB
Unlike regular Interlace Scan, in which two fields of picture information alternate to create the entire
picture (odd scan lines, then even scan lines), Progressive Scan uses one field of information (all lines
displayed in one pass) to create a clear and detailed picture without visible scan lines.
Connecting an External Analog Component
1
Press STOP button.
• If playing a disc, press the STOP button twice so that “STOP”, appears on the display.
2
Press and hold P.SCAN button on the remote control for over 5 seconds.
• Pressing and holding the button for over 5 seconds will select "Progressive Scan" and "Interlace Scan"
Example: Analog signal components such as a VCR.
CONNECTIONS
alternately.
• When you select P.SCAN, "P.SCAN" will appear on the display.
• To set P.Scan mode for DivX discs, press the P.SCAN button on the remote control for more than
5 seconds with no disc in the unit (“'NO DISC" on the display), then load the DivX disc and play.
Audio Cable
(not supplied)
If the external analog component has only one Audio Out,
connect either left or right.
What is Progressive (or Non-Interlaced) Scanning?
Interlaced Scan (1 FRAME = 2 FIELDS)
In interlaced-scan video, a frame consists of two interlaced fields (odd and even), where each field contains
every other horizontal line in the frame.
The odd field of alternating lines is displayed first, and
then the even field is displayed to fill in the alternating
gaps left by the odd field to form a single frame.
One frame, displayed every 1/30th of a second, contains
two interfaced fields, thus a total of 60 fields are displayed every 1/60th of a second.
The interlaced scanning method is intended for capturing
a still object.
Note
The progressive scanning method scans one full frame of
video consecutively down the screen, line by line.
An entire image is drawn at one time, as opposed to the
interlaced scanning process by which a video image is
drawn in a series of passes.
The progressive scanning method is desirable for dealing
with moving objects.
• This function works only on TVs equipped with component video inputs (Y, Pr, Pb) that support
•
17
Progressive Scan (FULL FRAME)
Progressive Video. (It does not work on TVs with conventional component inputs, i.e., non-progressive
scan TVs.)
Depending on the capabilities of your TV, this function may not work.
1
Connect AUX (Audio) In on the Home Theater to Audio Out on the external analog component.
• Be sure to match connector colors.
2
Press AUX button on the remote control to select ‘AUX’ input.
• You can also use the FUNCTION button on the main unit.
The mode switches as follows: DVD/CD ➝ AUX ➝ USB ➝ FM
Note
• You can connect the Video Output jack on your VCR to the TV, and connect the Audio
Output jacks on the VCR to this product.
18
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 22
Connecting the FM Antenna
Before Using Your Home Theater
GB
Your Home Theater is capable of playing DVD, CD, MP3/WMA and JPEG discs.Depending on the disc you are
using, these instructions may vary slightly. Read the instructions carefully before using.
To Operate your Samsung TV and the Home Theater with the HT-WQ20/HT-TWQ22/HT-TWQ25's Remote Control
1
Plug the main unit's
power cord into the
AC power supply.
3
Press the POWER
button to turn on
your Samsung TV
with this remote.
2
Press TV button to
set the remote to TV
mode.
FM Antenna (supplied)
VIDEO
1 Connect the FM antenna supplied to the FM 75Ω COAXIAL terminal.
2 Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall or other rigid surface.
Cooling Fan
5
The cooling fan supplies cool air to the unit to prevent overheating.
Please observe the following cautions for your safety.
• Make sure the unit is well-ventilated. If the unit has poor ventilation, the temperature inside the unit could rise
Press DVD RECEIVER
button to switch to
DVD RECEIVER
mode.
6
Press FUNCTION button
on the main unit or DVD
button on the remote to
enable DVD/CD playback.
and may damage it.
• Do not obstruct the cooling fan or ventilation holes. (If the cooling fan or ventilation holes are covered with a
newspaper or cloth, heat may build up inside the unit and fire may result.)
Note
• This unit does not receive AM broadcasts.
Note
19
• Buttons Enabled for TV Operation: POWER, CHANNEL, VOLUME, TV/VIDEO, and Numeric (0-9) buttons.
• By default, the remote control is set to work with Samsung TVs.
See page 67 for more information about remote control operation with other manufacturer's TVs.
20
OPERATION
4
Press TV/VIDEO
button to select
VIDEO mode on
your TV.
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 24
Before Using Your Home Theater
Disc Playback
Disc terminology
Titles and chapters (DVD-VIDEO)
GB
1
Press OPEN/CLOSE button to open the
disc tray.
2
Load a disc.
3
Close the compartment by pressing the
OPEN/CLOSE button again.
• DVD-video is divided into several large sections called "titles" and smaller sections called "chapters".
Numbers are allotted to these sections.
These numbers are called "title numbers" and "chapter numbers".
TITLE 1
CHAPTER 1
CHAPTER 2
TITLE 2
CHAPTER 3
CHAPTER 1
CHAPTER 2
Tracks (Video and music CDs)
facing up.
DVD
Numbers are allotted to these sections. These numbers are called "track numbers".
VCD
OPERATION
• Video and music CDs are divided into sections called "tracks".
• Place a disc gently into the tray with the disc’s label
CD
• Playback starts automatically.
TRACK 1
TRACK 2
TRACK 3
TRACK 4
TRACK 5
To stop playback, press STOP during playback.
• If pressed once, “PRESS PLAY” is displayed and the stop position will be
stored in memory. If PLAY/PAUSE (
) button or ENTER button is
pressed, playback resumes from the stop position. (This function works only
with DVDs.)
Files (DivX)
• DivX is divided into sections called "files".
• If pressed twice, “STOP” is displayed, and if PLAY/PAUSE (
Numbers are allotted to these sections. These numbers are called "file numbers".
) button is
pressed, playback starts from the beginning.
FILE 1
FILE 2
To temporarily pause playback, press PLAY/PAUSE
during playback.
• To resume playback, press PLAY/PAUSE (
Note
• In this manual, the instructions marked with "DVD (
DVD
• Depending on the content of the disc, the initial screen may appear different.
21
Selecting the Video Format
)" are applicable
to DVD-VIDEO and DVD-R/RW discs.
Where a particular DVD type is mentioned, it is indicated separately.
) button again.
Note
• Depending on the content of
the disc, the initial screen may
appear different.
Press and hold NT/PAL button on the remote controller for over 5 seconds
while the power is turned off.
• By default, the video format is set to "PAL".
• "NTSC" or "PAL" will appear in the display. At this time, press the NT/PAL button
shortly to select between "NTSC" and "PAL".
• Each country has a different video format standard.
• For normal playback, the video format of the disc must be the same as the video
format of your TV.
22
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 26
MP3/WMA-CD Playback
Displaying Disc Information
Data CDs (CD-ROM, CD-R, CD-RW) encoded in MP3/WMA format can be played.
1
Press the
OPEN/CLOSE button
to open the disc tray,
and then load the
MP3/WMA disc.
• The MP3/WMA menu screen will appear
•
•
and playback will start.
The appearance of the menu depends on
the MP3/WMA disc.
WMA-DRM files cannot be played.
2
You can view disc playback information on the TV screen.
In Stop mode, use
to select
the album, and then
press the ENTER
button.
• Use
to select the track.
Press INFO button.
• Each time the button is pressed, the display changes as follows:
DVD
VCD
CD
MP3
3
•
4
Press the STOP
button to stop
playback.
23
Icon.
•
tion display may appear different.
Depending on the disc, you can also
select DTS, DOLBY DIGITAL, or PRO
LOGIC.
• What is a Chapter?
Each title on a DVD disc is divided into several smaller sections called
"chapters".
• What is a Track (File)?
A section of video or a music file recorded on a CD, or MP3-CD.
Screen Display
To play a file icon in the screen,
Icon.
A movie contained in a DVD-VIDEO disc.
• Depending on the disc, the disc informa-
mat recorded on the disc.
•
• To view image files only, select the
• To view movie files only, select the
Icon.
• To select all files select the
appears on the TV screen!
• What is a Title?
Note • Depending on the recording mode, some MP3/WMA-CDs may not play.
• Table of contents of a MP3-CD varies depending on the MP3/WMA track for-
Icon.
The information Display disappears from the screen
The information Display disappears from the screen
Note
repeat Steps 2 and 3 above.
To play music files only, select the
JPEG
If this symbol appears on the TV screen while buttons are being operated,
that operation is not possible with the disc currently being played.
• To select another album and track,
Press the
button when it is in stop
status and select a desired icon from the top
part of the menu.
DivX
DVD display
• Music File Icon
• Image File Icon
• Movie File Icon
• All File Icon
VCD display
CD display
TITLE display
ELAPSED TIME display
STEREO (L/R) display
REPEAT PLAYBACK display
DOLBY DIGITAL display
AUDIO LANGUAGE display
ANGLE display
CHAPTER display
TRACK (FILE) display
SUBTITLE display
24
OPERATION
The information Display disappears from the screen
To change the album,
use
to
select another album
in Stop mode, and
then press the
ENTER button.
GB
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 28
JPEG File Playback
JPEG
Images captured with a digital camera or camcorder, or JPEG files on a PC can be stored on a CD and then
played back with this Home Theater.
1
Place the JPEG disc on the disc tray.
2
Press the OPEN/CLOSE button.
Press DIGEST
button during
playback.
2
• JPEG files will be shown in
Press Cursor , , , buttons
to select the desired image and
then press ENTER button.
• The selected image is played for 5 seconds before moving
9 windows.
to the next image.
To view the previous or next image with 9 windows, press
.
OPERATION
•
•
You can view 9 JPEG images on the TV screen.
1
Slide Mode
3
GB
Digest Function
Rotate/Flip Function
Press SLIDE MODE button.
Press Cursor
,
,
,
buttons during playback.
Playback starts automatically.
Each time the button is pressed, the image makes the transition as follows:
From top to bottom
From bottom to top
button: Flip Vertically
Rectangular shape in the center
button: Rotate 90°
Counterclockwise
button: Rotate 90° Clockwise
Original Image
Vertical blinds effect
Each time a new image is displayed, slide modes
(1~11) will be applied randomly and automatically.
button: Flip Horizontally
Cancels the slide mode.
Note
• The maximum resolutions supported by this product are 5120 x 3480 (or 19.0 MPixel) for
standard JPEG files and 2048 x 1536 (or 3.0 MPixel) for progressive image files.
Press
25
to skip to the next slide.
• Each time the button is pressed, the slide moves backward or forward.
26
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 30
DivX Playback
GB
Subtitle Display
The functions on this page apply to DIVX disc playback.
Press the SUBTITLE button.
Skip Forward/Back
During playback, press the
button.
• Goes to the next file whenever you press
•
button, if there are over
2 files in the disk.
Goes to the previous file whenever you press
over 2 files in the disk.
button, if there are
• Each time you press the button, your selection will toggle between “SUBTITLE (1/1, 1/2 ...)” and “SUBTITLE OFF”.
• If the disc has only one subtitle file, it will be played automatically.
• See number 2 (Caption Function) below for more details concerning Subtitle usage with DIVX discs.
Audio Display
Press the AUDIO button.
• If there are multiple audio tracks on a disc, you can toggle between them.
• Each time you press the button, your selection will toggle between “AUDIO(1/1, 1/2 ...)” and
Fast playback
To play back the disc at a faster speed,
press
or
during playback.
follows:
2x ➞ 4x ➞ 8x ➞ 32x ➞ Normal.
•"
”.
" is displayed when there is one supported language in the disc.
DivX(Digital internet video eXpress)
DivX is a video file format developed by Microsoft and is based on MPEG4 compression technology
to provide audio and video data over the Internet in real-time.
MPEG4 is used for video encoding and MP3 for audio encoding so that the users can watch a movie
at near DVD-quality video and audio.
1. Supported Formats
5 Minute Skip function
• This product only supports the following media formats.If both video and audio formats are not supported, the user may experience problems such as broken images or no sound.
●
During playback, press the
, button.
Format
Supported Versions
• Playback skips 5 minutes forward whenever you press button.
• Playback skips 5 minutes back whenever you press button.
●
Press ZOOM
button.
2
Press Cursor , ,
, buttons to move
to the area you want
to enlarge.
• Each time you press the button,
your selection will toggle between
“ZOOM X2” and “ZOOM OFF”.
Note
27
• DIVX file can be zoomed only in ZOOM X2 mode.
• DivX files have .Avi file extensions, however, not all .Avi files are DivX
and may not be playable in this unit.
AVI
DivX3.11 ~ 5.1
WMV
V1/V2/V3/V7
Supported Audio Formats
Format
Bit Rate
Sampling Frequency
Zoom Function
1
Supported Video Formats
MP3
WMA
80~384kbps
56~128kbps
44.1khz
AC3
128~384kbps
44.1/48khz
DTS
1.5Mbps
44.1khz
• DivX files, including audio and video files, created in the DTS format can only support up to 6Mbps.
• Aspect Ratio: Although default DivX resolution is 640*480 pixels (4:3), this product supports up to
720*480 pixels (16:9). TV screen resolutions higher than 800 will not be supported.
• When you play a disc whose sampling frequency is higher than 48khz or 320kbps, you may experience shaking on the screen during playback.
2. Caption Function
• You must have some experience with video extraction and editing in order to use this feature properly.
• To use the caption function, save the caption file (*.smi) in the same file name as that of the DivX
•
media file (*.avi) within the same folder.
Example. Root
Samsung_007CD1.avi
Samsung_007CD1.smi
Up to 60 alphanumeric characters or 30 East Asian characters (2 byte characters such as Korean and
Chinese) for the file name.
28
OPERATION
• Each time you press either button, the playback speed will change as
Note
“
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 32
Checking the Remaining Time
Fast/Slow Playback
Fast Playback
DVD
VCD
CD
Slow Playback
MP3
Press SLOW button.
Press the REMAIN button.
Press
• For checking the total and remaining time of a title or chapter
• Each time the button is pressed during playback,
being played.
GB
.
the playback speed changes as follows:
• Each time the button is pressed during playback,
the playback speed changes as follows:
DVD
VCD
DivX
Each time the REMAIN button is pressed
DVDVIDEO
VCD
CD
TRACK ELAPSED
TITLE REMAIN
TRACK REMAIN
CHAPTER ELAPSED
TOTAL ELAPSED
Note
• No sound is heard during slow playback
Note
• During fast playback of a CD or MP3-CD, sound is
CHAPTER REMAIN
TOTAL REMAIN
heard only at 2x speed, and not at 4x, 8x, and 32x
speeds.
and step motion playback.
• Reverse slow playback does not
work with VCD and DivX.
Skipping Scenes/Songs
Press
MP3
.
• Each time the button is pressed during playback, the previous or next chapter, track, or
directory (file) will be played.
• You cannot skip chapters consecutively.
TRACK REMAIN
DVD
VCD
MP3
TRACK ELAPSED
TITLE 01/05 CHAPTER 002/040
TITLE 01/05 CHAPTER 004/040
• When watching a VCD with a track
29
longer than 15 minutes, each time
is pressed, playback
will skip back or forward 5 minutes.
30
OPERATION
TITLE ELAPSED
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 34
Repeat Playback
A-B Repeat Playback
Repeat playback allows you to repeatedly play a chapter, title, track (song), or directory (MP3 file).
DVD
VCD
CD
MP3
GB
You can repeatedly play back a designated section of a DVD.
JPEG
DVD
VCD
Press REPEAT button.
• Each time the button is pressed during playback, the repeat playback mode changes as follows:
DVDVIDEO
VCD
CD
Repeat Playback Options
CHAPTER
Repeatedly plays the selected chapter.
1
Press INFO button
twice.
2
Press Cursor button
to move to REPEAT
PLAYBACK ( ) display.
4
Press ENTER
button at the end
of the desired
segment.
• For a VCD, press INFO button
once.
TITLE
Repeatedly plays the selected title.
MP3
RANDOM
Plays tracks in random order.
(A track that has already been played may be
played again.)
JPEG
DIR
Repeatedly plays all tracks in the selected folder.
DISC
Repeatedly plays the entire disc.
3
• When ENTER button is pressed,
the selected position will be stored
in memory.
• The specified segment will be
played repeatedly.
A-
OFF
Cancels Repeat Playback.
A-B
REPEAT : A—B
A -?
REPEAT : A—
To Select a Repeat Playback Mode in the Disc Information Screen
Note
• Repeat playback operation is
not possible with version 2.0
VCD discs if PBC is turned
on. To use Repeat Playback
on a VCD with PBC, you
should set the PBC to OFF in
the disc menu. (See page
40.)
31
1
2
Press INFO button twice.
3
Press Cursor button
to select the desired
Repeat Playback mode.
4
Press ENTER button.
DVD
Press Cursor button to
move to REPEAT PLAYBACK ( ) display.
To return to normal playback, press Cursor
buttons to select
OFF.
,
Note
VCD
CD
MP3 and JPEG discs, you cannot select Repeat
* For
Play from the information display screen.
• The A-B Repeat function does not operate with MP3, CD or JPEG discs.
32
OPERATION
TRACK
Repeatedly plays the selected track.
Press Cursor , buttons
to select ‘A-’ and then press
ENTER button at the beginning
of the desired segment.
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 36
Step Function
DVD
Zoom (Screen Enlarge) Function
VCD
This function allows you to enlarge a particular area of the displayed image.
DVD
GB
VCD
Press STEP button.
• The picture moves forward one frame each time the button is pressed
1
during playback.
Press ZOOM button.
2
Press Cursor , ,
, buttons to
move to the area
you want to enlarge.
3
Press ENTER button.
• Each time the button is pressed, the
zoom level changes as follows:
SELECT ZOOM POSITION
Angle Function
DVD
This function allows you to view the same scene in different angles.
2
Press Cursor button to move to
ANGLE ( ) display.
1/3
3
1/3
Press Cursor , or numeric buttons to
select the desired angle.
• Each time the button is pressed, the angle changes as follows:
1/3
Note
OPERATION
1
Press INFO button.
• When a DivX disc is being played, only the 2:1 zoom-in is available.
EZ VIEW Function
DVD
Press EZ VIEW button.
• Each time the button is pressed, the zoom function will switch between On
and Off.
• When a movie is played in Widescreen format, black bars at the top and bottom of the TV screen can be removed by pressing the EZ VIEW button.
2/3
3/3
EZ VIEW
EZ VIEW OFF
Note
Note
• The Angle function works only with discs on which multiple
angles have been recorded.
33
• This function will not work if the DVD is recorded with multi-camera angle format.
• Black bars may not disappear because some DVD discs have a built-in horizontal to vertical ratio.
• This feature is not supported for DivX discs.
34
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 38
Selecting Audio Language
Selecting Subtitle Language
Audio Language Selection Function
Subtitle Language Selection Function
1
Press INFO button
twice.
2
DVD
Press Cursor ,
buttons or numeric buttons to select the
desired audio language.
1
Press INFO button
twice.
3
Press Cursor
button or numeric
buttons to select
the desired subtitle.
2
GB
DVD
Press Cursor
button to move to
SUBTITLE ( )
display.
• Depending on the number of languages on a DVD disc, a different
audio language (ENGLISH, SPANISH, FRENCH, etc.) is selected each
time the button is pressed.
FR 3/3
EN 1/3
EN 01/ 03
OPERATION
SP 2/3
OFF
SP 02/ 03
FR 03/ 03
OFF / 03
Note
• To operate this function, you can also press the Select AUDIO or Select SUBTITLE buttons on the remote control.
• Depending on the disc, the Subtitle and Audio Language functions
may not be available.
35
36
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 40
Playing Media Files using the USB HOST feature
GB
You can enjoy media files such as pictures, movies and music saved in an MP3 player, USB memory or digital camera in high
quality video with 5.1 channel home theater sound by connecting the storage device to the USB port of the home theater.
1
Connect the USB
device to the USB
port on the rear of
the unit.
2
Compatible Devices
1. USB devices that support USB Mass Storage v1.0.
(USB devices that operate as a removable disk in Windows
(2000 or later) without additional driver installation.)
2. MP3 Player: HDD and flash type MP3 players.
3. Digital camera: Cameras that support USB Mass Storage v1.0.
• Cameras that operate as a removable disk in Windows (2000 or later) without additional driver installation.
4. USB HDD and USB Flash Drive: Devices that support USB2.0 or USB1.1.
• You may experience a difference in playback quality when you connect a USB1.1 device.
• For a USB HDD, make sure to connect an auxiliary power cord to the USB HDD for proper operation.
5. USB card Reader: One slot USB card reader and Multi slot USB card reader
• Depending on the manufacturer. the USB card reader may not be supported.
• If you install multiple memory devices into a multi card reader, you may experience problems.
6. If you use a USB extension cable, the USB device might not be recognized.
Press the FUNCTION
button on the main unit
or the USB button on
the remote control to
select the USB mode.
• “USB” appears on the display screen
and then disappears.
• USB MENU screen appears on the TV
screen and the saved file is played.
To stop playback, press the STOP (
) button.
Music
To prevent damage to the memory stored in the USB device, perform safe removal
before disconnecting the USB cable.
Movie
(1) Press the Stop button twice in a row.
The display will show REMOVE ➞ USB.
File name
File
extension
JPG
JPG .JPEG
MP3
.MP3
WMA
.WMA
56~128kbps
V8
–
44.1kHz
VCD
MPG.MPEG .DAT
1.5Mbps
VCD1.1,VCD2.0
320*480
44.1KHz
WMV
.WMV
4Mbps
V1,V2,V3,V7
720*480
44.1KHz~48KHz
DivX
.AVI,.ASF
4Mbps
DivX3.11~DivX5.1,Xvid
720*480
44.1KHz~48KHz
Bit rate
Sampling
Frequency
Version
Pixel
–
–
640*480
–
80~384kbps
–
–
44.1kHz
• CBI (Control/Bulk/Interrupt) is not supported.
(2) Remove the USB cable.
• Digital Cameras that use PTP protocol or require additional program installation
when connected to a PC are not supported.
Skip Forward/Back
During playback, press the
Supported Formats
Still Picture
Safe USB Removal
OPERATION
●
• A device using NTFS file system is not supported.
(Only FAT 16/32 (File Allocation Table 16/32) file system is supported.)
button.
• When there is more than one file, when you press the
• When there is more than one file, when you press the
button, the next file is selected.
button, the previous file is selected.
• The USB HOST function is not supported if a product that transfers media files by
its manufacturer-specific program is connected.
Fast playback
To play back the disc at a faster speed, press
back.
• Some MP3 players, when connected to this product,may not operate depending
on the sector size of their file system.
or
• Each time you press either button, the playback speed will change as follows:
during play-
• Does not operate with Janus enabled MTP(Media Transfer Protocol) devices.
• The USB host function of this product does not support all USB devices.
For information on the supported devices, see pages 73.
2x ➞ 4x ➞ 8x ➞ 32x ➞ Normal.
37
38
HT-WQ20(1~40P) GB
2003.4.11
5:49 PM
Page 42
Moving Directly to a Scene/Song
Using Disc Menu
GB
DVD
You can use the menus for the audio language, subtitle language, profile, etc.
DVD menu contents differ from disc to disc.
DVD
1
VCD
CD
Moving to a Title/Track
2
Press INFO button.
01/05
001/040
0:00:37
1/1
Press Cursor , buttons
or numeric buttons to select
the desired title/track and then
press ENTER button.
03/05
001/002
0:00:01
Moving to a Chapter
Press Cursor ,
buttons to move to
Chapter ( ) display.
3
1
In Stop mode,
press MENU
button.
• When playing a VCD (version
2.), this toggles between PBC
ON and OFF.
1/1
01/05
001/040
0:00:01
Press Cursor , buttons or numeric buttons to
select the desired chapter
and then press ENTER button.
01/05
025/040
0:00:01
5
1/1
Press Cursor ,
buttons to move to
time display.
01/05
025/040
1:17:30
supported by the disc, the "This menu is not supported" message appears on the screen.
• Press ENTER button.
ENTER
MOVE
EXIT
ENTER
EXIT
Moving to a Specific Time
6
Press the numeric
buttons to select the
desired time and then
press ENTER button.
1/1
01/05
028/040
1:30:00
1/1
• Disc menu display may be different depending on the disc.
Note
PBC (Playback Control) Function
When playing a VCD (version 2.0), you can select and view various scenes according to the menu screen.
PBC ON: This VCD disc is version 2.0. The disc is played back according to the menu screen. Some functions
may be disabled. When some functions are disabled, select "PBC OFF" to enable them.
PBC OFF: This VCD disc is version 1.1. The disc is played back in the same way as with a music CD.
Using the Title Menu
DVD
For DVDs containing multiple titles, you can view the title of each movie.
Depending on the disc, the availability of this feature may vary.
MP3
JPEG
Press the numeric
buttons.
• The selected file will be played.
• When playing an MP3 or JPEG disc, you
cannot use
,
to move to a folder.
To move a folder, press (Stop) and
then press
, .
Note
1
In Stop mode,
press MENU button.
2
Press Cursor ,
button to move to
‘Title Menu’.
• You can press
•
on the
remote control to move directly to the
desired title, chapter, or track.
Depending on the disc, you may not
be able to move to the selected title
or time.
3
Press ENTER button.
• The title menu appears.
MOVE
ENTER
EXIT
MOVE
ENTER
EXIT
Press MENU button to exit the setup screen.
39
Note
• Title menu display may be different depending on the disc.
40
OPERATION
4
Moving to a Specific Time
• When you select Disc Menu and it is not
3
Press Cursor ,
, buttons to
select the desired
item.
1/1
MOVE
Moving to a Chapter
2
Press Cursor ,
buttons to move to
‘DISC MENU’ and then
press ENTER button.
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 40
Setting the Language
GB
OSD (On-Screen Display) language is set to English by default.
1
In Stop mode,
press MENU
button.
2
Press Cursor button to move to
‘Setup’ and then
press ENTER button.
3
Select ‘Language’
and then press
ENTER button
4
Press Cursor ,
button to select ‘OSD
Language’ and then
press ENTER button.
5
Press Cursor , button to select the desired
language and then press
ENTER button.
• Once the setup is complete, the OSD will be
English if English has been selected as language.
MOVE
ENTER
EXIT
MOVE
ENTER
EXIT
MOVE
ENTER
RETURN
EXIT
MOVE
ENTER
RETURN
EXIT
MOVE
SELECT
RETURN
EXIT
Press MENU button to exit the setup screen.
Note
• To select another language, select OTHER and enter the language code of your country.
(See page 72 for language codes)
AUDIO, SUB TITLE and DISC MENU language can be selected.
MOVE
ENTER
RETURN
Selecting the
OSD Language
MOVE
41
SELECT
RETURN
EXIT
EXIT
MOVE
ENTER
RETURN
EXIT
Selecting the
Audio Language (recorded on the disc)
MOVE
ENTER
RETURN
EXIT
Selecting the
Subtitle Language
(recorded on the disc)
MOVE
ENTER
RETURN
EXIT
Selecting the Disc Menu
Language (recorded on the disc)
language you selected is
* Ifnottherecorded
on the disc, menu
language will not change even
if you set it to your desired
language.
42
SETUP
Press RETURN button to return to the previous level.
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 42
Setting TV Screen type
GB
Depending on your TV type (Wide Screen or conventional 4:3), you can select the TV's aspect ratio.
1
In Stop mode,
press MENU
button.
2
Press Cursor button to move to
‘Setup’ and then
press ENTER button.
Adjusting the TV Aspect Ratio (Screen Size)
The horizontal to vertical screen size ratio of conventional TVs is 4:3, while that of widescreen and high
definition TVs is 16:9. This ratio is called the aspect ratio. When playing DVDs recorded in different
screen sizes, you should adjust the aspect ratio to fit your TV or monitor.
• For a standard TV, select either "4:3LB" or "4:3PS" option according to personal preference.
Select "16:9" if you have a widescreen TV.
WIDE
MOVE
3
ENTER
MOVE
EXIT
Press Cursor button to move to ‘TV
DISPLAY’ and then
press ENTER button.
4
ENTER
• You can enjoy the widescreen aspect.
EXIT
Press Cursor ,
button to select the
desired item and then
press ENTER button.
• Once the setup is complete, you will
4:3LB
(4:3 Letterbox)
4:3PS
(4:3 Pan&Scan)
EXIT
MOVE
SELECT
RETURN
EXIT
SETUP
RETURN
: Select this to play a 16:9 picture in the pan & scan
mode on a conventional TV.
• You can see the central portion of the screen only (with the
sides of the 16:9 picture cut off).
Note
ENTER
: Select this to play a 16:9 picture in the letter box
mode on a conventional TV.
• Black bars will appear at the top and bottom of the screen.
be taken to the previous screen.
MOVE
: Select this to view a 16:9 picture in the full-screen
mode on your widescreen TV.
• If a DVD is in the 4:3 ratio, you cannot view it in widescreen.
• Since DVD discs are recorded in various image formats, they will look different depending on
the software, the type of TV, and the TV aspect ratio setting.
Press RETURN button to return to the previous level.
Press MENU button to exit the setup screen.
43
44
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 44
Setting Parental Controls (Rating Level)
Use this to restrict playback of adult or violent DVDs you do not want children to view.
1
In Stop mode,
press MENU
button.
2
Setting the Password
You can set the password for the Parental (rating level) setting.
Press Cursor button to move to
‘Setup’ and then
press ENTER button.
1
Press MENU button.
MOVE
MOVE
3
4
Press Cursor , button to select the desired
rating level and then press
ENTER button.
• If you have selected Level 6, you can•
MOVE
EXIT
not view DVDs with Level 7 or higher.
The higher the level, the closer the
content is to violent or adult material.
EXIT
ENTER
3
5
Enter the password
and then press
ENTER button.
Press Cursor button to
move to ‘PASSWORD’
and then press ENTER
button.
Note
RETURN
EXIT
MOVE
SELECT
RETURN
EXIT
Press ENTER button.
5
ENTER
EXIT
Enter the password
and then press
ENTER button.
word, and confirm new password.
• The setting is complete.
• The password is set to "7890" by default.
• Once the setup is complete, you will be
taken to the previous screen.
Note
ENTER
MOVE
EXIT
ENTER
• Enter the old password, a new pass-
MOVE
MOVE
4
2
Press Cursor button to move to
‘Setup’ and then
press ENTER button.
SETUP
Press Cursor button to move to
‘PARENTAL’ and then
press ENTER button.
ENTER
GB
INPUT NUMBER
RETURN
• This function works only if a DVD disc contains the rating level information.
ENTER
RETURN
EXIT
MOVE
SELECT
RETURN
EXIT
INPUT NUMBER
EXIT
RETURN
• The password is set to "7890" by default.
EXIT
If you have forgotten the rating level password, do the following:
• While the player is in the no disc mode, hold the main unit's
Press RETURN button to return to the previous level.
45
Press MENU button to exit the setup screen.
button for longer than 5 seconds. “INITIALIZE”
appears on the display and all settings will return to the default values.
• Press the POWER button.
Using the RESET function will erase all stored settings.
Do not use this unless necessary.
46
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 46
Setting the Wallpaper
JPEG
DVD
GB
VCD
While watching a DVD, VCD or JPEG CD, you can set the image you like as background wallpaper.
Setting the Wallpaper
1
During playback, press
PLAY/PAUSE button
when an image you
like appears.
To select one of the 3 wallpaper settings you've made
Press LOGO button.
2
1
In Stop mode,
press MENU
button.
2
Press Cursor button to move to
‘Setup’ and then
press ENTER button.
3
Press Cursor button to move to
‘LOGO’ and then
press ENTER button.
• “COPY LOGO DATA” will be displayed on the TV screen.
COPY LOGO DATA
PAUSE
MOVE
3
4
The power will
turn off and then
back on.
5
EXIT
MOVE
ENTER
RETURN
EXIT
Press MENU button to exit the
setup screen.
SETUP
Press to select
the desired ‘USER’,
and then press
ENTER.
ENTER
• This selects one of the 3 wallpa-
• The selected wallpaper will be
•
MOVE
EXIT
ENTER
per screens
displayed.
You can select up to 3 wallpaper
settings.
MOVE
SELECT
RETURN
EXIT
Press RETURN button to return to the previous level.
MOVE
47
SELECT
RETURN
EXIT
Select this to set the
Samsung Logo image as
your wallpaper.
MOVE
SELECT
RETURN
EXIT
Press MENU button to exit the setup screen.
Select this to set the desired
image as your wallpaper.
48
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 48
DivX (R) registration
Setting the Speaker Mode
Please use the Registration code to register this player with the DivX (R) video on demand format.
To learn more, go to www.divx.com/vod.
1
Press the MENU
button while the
disc tray is open.
MOVE
EXIT
ENTER
2
Signal outputs and frequency responses from the speakers will automatically be adjusted according to your
speaker configuration and whether certain speakers are used or not.
Press Cursor button to move to
‘Setup’ and then
press ENTER button.
MOVE
ENTER
1
In Stop mode,
press MENU
button.
2
Press Cursor button to move to ‘Audio’
and then press
ENTER button.
EXIT
MOVE
3
GB
Press Cursor button to move to
‘DIVX(R) registration’
and then press
ENTER button.
3
EXIT
ENTER
In the Speaker
Setup, press the
ENTER button
again.
MOVE
4
EXIT
ENTER
Press Cursor , ,
, buttons to
move to the desired
speaker and then
press ENTER button.
• For C, SL, and SR, each time the button
MOVE
ENTER
RETURN
EXIT
MOVE
ENTER
RETURN
EXIT
MOVE
CHANGE
RETURN
EXIT
SMALL : Select this when using the speakers.
NONE : Select this when no speakers are connected.
Note
• Depending on PRO LOGIC and STEREO settings, the speaker mode may vary (see page 59).
49
50
SETUP
•
is pressed, the mode switches alternately as follows: SMALL ➝ NONE.
For L and R, the mode is set to SMALL.
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 50
Setting the Delay Time
GB
If the speakers cannot be placed at equal distances from the listening position, you can adjust the delay time of
the audio signals from the center and rear speakers.
1
In Stop mode,
press MENU
button.
2
Press Cursor button
to move to ‘Audio’ and
then press ENTER button.
3
Press Cursor button
to move to ‘DELAY
TIME’ and then press
ENTER button.
4
Press Cursor , ,
, buttons to move
to the desired speaker
and then press
ENTER button.
5
Press Cursor ,
to set the Delay
time.
• You can set the delay time for C
between 00 and 05mSEC and for
SL and SR between 00 and
15mSEC.
MOVE
ENTER
EXIT
MOVE
ENTER
EXIT
MOVE
ENTER
RETURN
EXIT
MOVE
SELECT
RETURN
EXIT
MOVE
CHANGE
RETURN
EXIT
SETUP
Setting up the Speaker Delay Time
When 5.1CH Surround Sound is played, you can enjoy the best sound if
the distance between you and each speaker is the same. Since the
sounds arrive at the listening position at different times depending on the
placement of speakers, you can adjust this difference by adding a delay
effect to the sound of the Center and Surround Speakers.
Note
(Dolby Pro Logic II), the delay time may be different for each mode.
• With
• With AC-3 and DTS, the delay time can be set between 00 and 15mSEC.
• The Center channel is only adjustable on 5.1 channel discs.
51
• Setting CENTER SPEAKER
If the distance of Dc is equal to or longer than the distance of Df in the figure, set the mode as 0ms.
Otherwise, change the setting according to the table.
Distance between Df and Dc
0 inch
13.6 inches
27.2 inches
40.8 inches
4.5 feet
5.6 feet
Delay Time
0 ms
1 ms
2 ms
3 ms
4 ms
5 ms
• Setting REAR (SURROUND) SPEAKERS
If the distance of Df is equal to the distance of Ds
in the figure, set the mode as 0ms. Otherwise,
change the setting according to the table.
Distance between Df and Ds
0 inch
40.8 inches
6.7 feet
10.0 feet
13.4 feet
16.7 feet
Ideal CENTER SPEAKER placement
Delay Time
0 ms
3 ms
6 ms
9 ms
12 ms
15 ms
Ideal SURROUND
SPEAKER
placement
It is desirable to place all speakers within this circle.
Df: The distance from FRONT SPEAKER
Dc: The distance from CENTER SPEAKER
Ds: The distance from SURROUND SPEAKER
52
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 52
Setting the Test Tone
Setting the DRC (Dynamic Range Compression)
Use the Test Tone feature to check the speaker connections.
1
In Stop or no
disc mode,
press MENU
button.
2
GB
This feature balances the range between the loudest and quietist sounds.
You can use this function to enjoy Dolby Digital sound when watching movies at low volume at night.
Press Cursor button to move to ‘Audio’
and then press
ENTER button.
3
Press Cursor button
to move to ‘TEST
TONE’ and then press
ENTER button.
1
In Stop or no disc
mode, press
MENU button.
2
• The test tone will be sent to L ➝ C ➝
Press Cursor
button to move to
‘Audio’ and then
press ENTER button.
R ➝ SR ➝ SL ➝ SW in order.
If the ENTER button is pressed again
at this time, the test tone will stop.
MOVE
ENTER
EXIT
MOVE
ENTER
EXIT
MOVE
MOVE
ENTER
RETURN
3
Press RETURN button to return to the previous level.
STOP
ENTER
MOVE
EXIT
ENTER
EXIT
EXIT
EXIT
4
Press Cursor
, to adjust
the ‘DRC’.
• When the Cursor
button is pressed,
the effect is greater, and when the
Cursor button is pressed, the effect is
smaller.
Alternate method: press the TEST TONE button on the remote.
Press TEST TONE button.
• Test tone will be produced as follows:
When playing a DVD or CD, this will work only in Stop mode.
• Use this function to check that each speaker is correctly con-
L: Front Speaker (L)
R: Front Speaker (R)
C: Center Speaker
SL: Rear Speaker (L)
SW: Subwoofer
SR: Rear Speaker (R)
Multi-Channel Pro Logic Mode
MOVE
ENTER
RETURN
EXIT
CHANGE
RETURN
EXIT
nected and that there is no problem.
To end the test tone,
press TEST TONE button again.
Start
Press RETURN button to return to the previous level.
Press MENU button to exit the setup screen.
53
54
SETUP
Press MENU button to exit the setup screen.
Press Cursor
button to move to
‘DRC’ and then
press ENTER button.
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 54
Setting the Audio
GB
You can adjust the balance and level for each speaker.
Method 1
1
In Stop mode,
press MENU button.
MOVE
3
When adjusting the audio quality using the setup screen
ENTER
RETURN
EXIT
4
ENTER
CHANGE
Adjusting Front Speaker Balance
1
Press SOUND
EDIT button and
then press Cursor
, .
Adjusting Rear Speaker Balance
Adjusting Center Speaker Level
Press SOUND
EDIT button and
then press Cursor
, .
Press SOUND
EDIT button and
then press Cursor
, .
2
3
EXIT
Press Cursor ,
buttons to select and
adjust the desired item.
Press the , buttons
to adjust the settings.
MOVE
When manually adjusting with the SOUND EDIT button
RETURN
Adjusting Rear Speaker Level
4
Press SOUND
EDIT button and
then press Cursor
, .
Adjusting Subwoofer Speaker Level
5
Press SOUND
EDIT button and
then press Cursor
, .
SETUP
ENTER
MOVE
EXIT
Press Cursor button
to move to ‘SOUND
EDIT’ and then press
ENTER button.
MOVE
2
Press Cursor
button to move to
‘Audio’ and then press
ENTER button.
Method 2
EXIT
Note
Press RETURN button to return to the previous level.
Press MENU button to exit the setup screen.
55
Adjusting Front/Rear Speaker Balance
• You can select between 00 and –06 and OFF.
• The volume decreases as you move closer to –6.
Adjusting Center/Rear/Subwoofer Speaker Level
• The volume level can be adjusted in steps from +6dB to –6dB.
• The sound gets louder as you move closer to +6dB and quieter as you get closer to -6dB.
56
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 56
AV SYNC Setup
Sound Field (DSP)/EQ Function
Video may look slower than the audio if it is connected to a digital TV.
If this occurs, adjust the audio delay time to to match the video.
1
Press the MENU button.
2
DSP(Digital Signal Processor) DSP modes have been designed to simulate different acoustic environments.
EQ: You can select ROCK, POP, or CLASSIC to optimize the sound for the genre of music you are playing
Press Cursor , buttons
to move to ‘Audio’ and then
press ENTER button.
3
ENTER
Press DSP/EQ button.
• "DSP" appears on the display panel.
• Each time the button is pressed, the selection changes as follows:
• Setup menu appears.
MOVE
MOVE
EXIT
4
ENTER
EXIT
Press Cursor
, buttons
to select the AV-SYNC Delay
Time and then press the
ENTER button.
SETUP
Press Cursor ,
buttons
to move to ‘AV-SYNC’ and
then press ENTER button.
• You can set the audio delay time between 0 ms
and 300 ms. Set it to the optimal status.
Note
• DSP/EQ function is only available in STEREO mode.
Press the
PL II mode button to show STEREO on the display.
• This feature works with CDs, MP3-CDs, 2 channel DivX and Dolby
Digital discs.
MOVE
ENTER
RETURN
EXIT
MOVE
SELECT
RETURN
EXIT
• When playing a DVD disc encoded with two or more channels,
multi-channel mode will be selected automatically and DSP/EQ
function does not work.
Press RETURN button to return to the previous level.
Press MENU button to exit the setup screen.
57
GB
POP, JAZZ, ROCK: Depending on the genre of music, you can select POP, JAZZ, and ROCK.
STUDIO : Provides a sense of presence as if in a studio.
CLUB : Simulates the sound of a dance club with a throbbing bass beat.
HALL : Provides a clear vocal as if listening in a concert hall.
MOVIE: Provides the feeling of a movie theater.
CHURCH: Gives the feel of being in a grand church.
PASS: Select this for normal listening.
58
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 58
Dolby Pro Logic II Mode
You can select the desired Dolby Pro Logic II audio mode.
Press
PL II MODE button.
• Each time the button is pressed, the mode changes as follows.
Dolby Pro Logic II Effect
GB
This function works only in Dolby Pro Logic MUSIC mode.
1
Press
PL II MODE button to select ‘MUSIC’ mode.
2
Press
PL II EFFECT button
to select Panorama, then press
Cursor ,
buttons to select
the desired effect setting.
• You can select either 0 or 1.
• This mode extends the front stereo image to
include the surround speakers for an exciting
"wraparound" effect with side wall imaging.
3
Note
• When selecting Pro Logic II mode, connect your external device to the
AUDIO INPUT jacks (L and R) on the player. If you connect to only one of
the inputs (L or R), you cannot listen to surround sound.
Press
PL II EFFECT button
to select C-Width, then press
Cursor , buttons to select
the desired effect setting.
• You can select between 0 and 7.
• This sets the width of the center image.
Note
• You can select between 0 and 6.
• Incrementally adjusts the sound field (DSP)from
the front or rear.
SETUP
The higher the setting, the less sound comes
from the center speaker.
4
Press
PL II EFFECT button
to select Dimension, then press
the Cursor , buttons to
select the desired setting.
• When playing a DVD disc encoded with two or more channels, multi-channel mode will be
selected automatically and
(Dolby Pro Logic II) button does not work.
PRO LOGIC II
• MUSIC: When listening to music, you can experience sound effects as if you are listening to the actual performance.
• CINEMA: Adds realism to the movie soundtrack.
• PRO LOGIC: You will experience a realistic multi-channel effect, as if using five speakers, while using just the front left
and right speakers.
• MATRIX: You will hear 5.1 channel surround sound.
STEREO: Select this to listen to sound from the front left and right speakers and the subwoofer only.
59
60
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 60
Listening to Radio
Remote Control Unit
Press the TUNER
button and select
the FM band.
1
Presetting Stations
GB
Example: Presetting FM 89.1 in the memory
2
Tune in to the
desired station.
Automatic Tuning 1
Automatic Tuning 2
Manual Tuning
1
Press the TUNER
button and select the
FM band.
When
is pressed, a
preset broadcast station is
selected.
Press and hold TUNING/CH to
automatically search for active
broadcasting stations.
2
Press TUNING/CH
to select "89.10".
3
• Refer to Step 2 on page 61 to
Press the TUNER
MEMORY button.
• “PRGM” flashes in the display.
automatically or manually tune in
to a station.
Briefly press TUNING/CH to
increase or decrease the
frequency incrementally.
Main Unit
1
Press the FUNCTION button to select
the FM band.
2
Select a broadcast
station.
Press the STOP ( )
button to select PRESET and then press
button to select the preset station.
Automatic Tuning 1
Press
to select preset
number.
4
• You can select between 1 and
15 presels.
5
Press the TUNER
MEMORY button
again.
6
To preset another
station, repeat steps
2 to 5.
• Press the TUNER MEMORY button before
‘PRGM’ disappears from the display.
• ‘PRGM’ disappears from the display and
the station is stored in memory.
RADIO OPERATION
Press the STOP ( ) button to select "MANUAL"
and then press and hold
button to automatically search the band.
Automatic Tuning 2
Press STOP ( ) to select
MANUAL and then briefly
press
to tune in to a lower or
higher frequency.
Manual Tuning
Press MO/ST button to listen in Mono/Stereo.
(This applies only when listening to an FM station.)
61
• Each time the button is pressed, the sound switches between "STEREO" and "MONO".
• In a poor reception area, select MONO for a clear, interference-free broadcast.
Note
• This unit does not receive
AM broadcasts.
To tune in to a preset station, press
remote control to select a channel.
on the
62
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 62
About RDS broadcasting
GB
PTY (Program Type) indication and PTY-SEARCH function
Using the RDS (Radio Data System) to receive FM stations
RDS allows FM stations to send an additional signal along with their regular program signals.
For example,the stations send their station names,as well as information about what type of
program they broadcast, such as sports or music,etc.
When tuned to an FM station which provides the RDS service,the RDS indicator
lights up on the display.
• Description on RDS function
1. PTY (Program Type) : Displays the type of programme currently being broadcast
2. PS NAME (Program Service Name) : Indicates the name of broadcasting station
and is composed of 8 characters.
3. RT (Radio Text) : Decodes the text broadcast by a station (if any) and is composed of maximum 64 characters.
4. CT (Clock Time) : Decodes the real time clock from the FM frequency.
• Some stations may not transmit PTY, RT or CT information therefore this may not be
displayed in all cases.
5. TA (Traffic Announcement) : When this symbol flashes it shows that the traffic announcement is in progress.
Note
• RDS may not operate correctly if the station tuned is not transmitting
RDS signal properly or if the signal strength is weak.
One of the advantages of the RDS service is that you can locate a particular kind of program from the
preset channels by specifying the PTY codes.
To search for a program using the PTY codes
Display
Before you start, remember...
NEWS
• The PTY Search is only applicable to preset sta•
•
•
tions.
To stop searching any time during the process,
press PTY SEARCH while searching.
There is a time limit in doing the following steps.
If the setting is cancelled before you finish, start
from step 1 again.
When pressing the buttons on the primary remote
control, make sure that you have selected the FM
station using the primary remote control.
1
Press PTY SEARCH while listening to an
FM station.
What information can RDS signals provide?
You can see the RDS signals the station sends on the display.
TO show the RDS signals
2
Press RDS DISPLAY while listening to an FM station.
Each time you press the button, the display change to show you the following information:
About characters shown in the display
When the display shows PS,or RT signals,the following characters are used.
• The display window cannot differentiate upper case and lower case letters and always
uses upper case letters.
• The display window cannot show accented letters, “A,” for instance, may stands for
accented “A’s” like “À, Â, Ä, Á, Åand Ã.”
Note
• If searching finishes at once,“PS”,and “RT” will not appear on the display.
63
3
Press PTY SEARCH again, while the PTY
code selected in the previous step is still on
the display.
• The center unit searches 15 preset FM
stations,stops when it finds the one you
have selected, and tunes in that station.
INFO
SPORT
EDUCATE
DRAMA
• Several matters including a current incident,
documentary, discussion and analysis.
• Information including weights and measures,
returns and forecast, matters interesting the
customer, medical information, etc.
• Sports
• Education
• Drama-Radio serial, etc.
CULTURE
• Culture-National or local culture including the
religious problem, social science, language,
theater,etc.
SCIENCE
• Natural science and technology
VARIED
• Others-Speech, amusing program (quiz,
game), interview, comedy and satirical play,
etc.
POP M
• Pop music
ROCK M
• Rock music
M.O.R.M
• Current contemporary music considered to be
“easy listening.”
LIGHT M
• Light classical music- Classical music and
instrumental and chorus music
CLASSICS
• Heavy classical music-Orchestra music, symphony, chamber music and opera
OTHER M
• Other music - Jazz, R&B country music
WEATHER
• Weather
FINANCE
• Finance
CHILDREN
• Children’s programmes
SOCIAL A
• Social affairs
RELIGION
• Religion
PHONE IN
• Phone in
TRAVEL
• Travel
LEISURE
• Leisure
JAZZ
• Jazz Music
COUNTRY
• Country Music
NATION M
• National Music
OLDIES
• Oldies Music
FOLK M
• Folk Music
DOCUMENT
RADIO OPERATION
PS (Program Service) :While searching,"PS"appears and then the station names will be
displayed."NO PS" appears if no signal is sent.
RT(RadioText) : while searching,"RT"appears and then text messages the station sends
will be displayed. "NO RT"appears if no signal is sent.
Frequency : station frequency (non-RDS service)
Press the PTY-or PTY+until the PTY code
you want appears on the display.
• The display gives you the PTY codes described
to the right.
AFFAIRS
Program Type
• News including an announced opinion and
report
• Documentary
64
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 64
Convenient Functions
Sleep Timer Function
You can set the time that the Home Theater will shut itself off.
Press SLEEP button.
• "SLEEP" will be displayed. Each time the button is pressed, the preset
time changes as follows: 10 ➝ 20 ➝ 30 ➝ 60 ➝ 90 ➝ 120 ➝ 150 ➝ OFF.
GB
Adjusting Display Brightness
You can adjust the brightness of the display on the main unit so it won't interfere
with your movie viewing.
Press DIMMER button.
• Each time the button is pressed, the brightness changes as follows:
DARK ➞ BRIGHT.
Mute Function
To confirm the sleep timer setting, press SLEEP button.
• The remaining time before the Home Theater will shut itself off is displayed.
• Pressing the button again changes the sleep time from what you have set earlier.
To cancel the sleep timer, press SLEEP button until
OFF appears on the display.
This is useful when answering a doorbell or telephone call.
Press MUTE button.
• ‘MUTE ON’ appears in the display.
• To restore the sound, press the button again to
select ‘MUTE OFF’.
MISCELLANEOUS
65
66
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 66
Operating a TV with the Remote Control
When operating a TV with the remote control
1
2
3
4
Press TV button to select TV mode.
Press POWER button to turn on the TV.
Point the remote control toward the TV.
While holding down POWER, enter the code
corresponding to your brand of TV.
• If the code matches the TV's code, the TV will be turned off.
• If there is more than one code listed for your TV in the table,
enter one at a time to determine which code works.
Example: For a Samsung TV
While holding down POWER, use the number buttons to enter 00,
01, 02, 03, 04, and 05.
5
Point the remote control toward the TV
and press POWER. If the TV turns off or
on, the setting is complete.
• You can use the TV POWER, VOLUME, CHANNEL, and Numeric
Note
• The remote control may not work on some brands of TVs. Also, some operations may not
•
67
be possible depending on your brand of TV.
If you do not set the remote control with the code for your brand of TV, the remote control
will work on a Samsung TV by default.
TV Brand Code List
No.
Brand
Code
No.
Brand
1
Admiral (M.Wards)
56, 57, 58
44
MTC
18
2
A Mark
01, 15
45
NEC
18, 19, 20, 40, 59, 60
3
Anam
01, 02, 03, 04, 05, 06, 07, 08, 09, 10,
46
Nikei
03
11, 12, 13, 14
47
Onking
03
Code
4
AOC
01, 18, 40, 148
48
Onwa
03
5
Bell & Howell (M.Wards)
57, 58, 81
49
Panasonic
06, 07, 08, 09, 54, 66, 67, 73, 74
6
Brocsonic
59, 60
50
Penney
18
7
Candle
18
51
Philco
03, 15, 17, 18, 48, 54, 59, 62, 69, 90
8
Cetronic
03
52
Philips
15, 17, 18, 40, 48, 54, 62, 72
9
Citizen
03, 18, 25
53
Pioneer
63, 66, 80, 91
10
Cinema
97
54
Portland
15, 18, 59
11
Classic
03
55
Proton
40
12
Concerto
18
56
Quasar
06, 66, 67
13
Contec
46
57
Radio Shack
17, 48, 56, 60, 61, 75
14
Coronado
15
58
RCA/Proscan
18, 59, 67, 76, 77, 78, 92, 93, 94
15
Craig
03, 05, 61, 82, 83, 84
59
Realistic
03, 19
16
Croslex
62
60
Sampo
40
17
Crown
03
61
Samsung
00, 15, 16, 17, 40, 43, 46, 47, 48, 49, 59, 60, 98
18
Curtis Mates
59, 61, 63
19
CXC
03
62
Sanyo
19, 61, 65
20
Daewoo
02, 03, 04, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 28, 29,
63
Scott
03, 40, 60, 61
30, 32, 34, 35, 36, 48, 59, 90
64
Sears
15, 18, 19
21
Daytron
40
65
Sharp
15, 57, 64
22
Dynasty
03
66
Signature 2000 (M.Wards)
57, 58
23
Emerson
03, 15, 40, 46, 59, 61, 64, 82, 83, 84, 85
67
Sony
50, 51, 52, 53, 55
24
Fisher
19, 65
68
Soundesign
03, 40
25
Funai
03
69
Spectricon
01
26
Futuretech
03
70
SSS
18
27
General Electric (GE)
06, 40, 56, 59, 66, 67, 68
71
Sylvania
18, 40, 48, 54, 59, 60, 62
28
Hall Mark
40
72
Symphonic
61, 95, 96
29
Hitachi
15, 18, 50, 59, 69
73
Tatung
06
30
Inkel
45
74
Techwood
18
31
JC Penny
56, 59, 67, 86
75
Teknika
03, 15, 18, 25
32
JVC
70
76
TMK
18, 40
33
KTV
59, 61, 87, 88
77
Toshiba
19, 57, 63, 71
34
KEC
03, 15, 40
78
Vidtech
18
35
KMC
15
79
Videch
59, 60, 69
36
LG (Goldstar)
01, 15, 16, 17, 37, 38, 39, 40, 41, 42, 43, 44
80
Wards
15, 17, 18, 40, 48, 54, 60, 64
37
38
Luxman
18
81
Yamaha
18
LXI (Sears)
19, 54, 56, 59, 60, 62, 63, 65, 71
82
York
40
39
Magnavox
15, 17, 18, 48, 54, 59, 60, 62, 72, 89
83
Yupiteru
03
40
Marantz
40, 54
84
Zenith
58, 79
41
Matsui
54
85
Zonda
01
42
MGA
18, 40
86
Dongyang
03, 54
43
Mitsubishi/MGA
18, 40, 59, 60, 75
MISCELLANEOUS
buttons (0~9).
GB
68
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 68
Before Calling for Service
GB
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or
if the instruction below does not help, turn off the unit, disconnect the power cord, and contact the nearest authorized dealer or Samsung Electronics Service Center.
Symptom
Disc tray does not open.
Check/Remedy
• Is the power cord plugged securely into the outlet?
• Turn off the power and then turn it back on.
• Check the region number of the DVD.
Playback does not start.
DVD discs purchased from abroad may not be playable.
Theater.
Make sure that the rating level is correct.
Playback does not start
• Are you using a deformed disc or a disc with scratches on
the surface?
immediately when the
• Wipe the disc clean.
Play/Pause button is pressed.
• No sound is heard during fast playback, slow playback, and step
•
•
motion playback.
Are the speakers connected properly? Is the speaker setup correctly customized?
Is the disc severely damaged?
• When listening to a CD or radio, sound is output to the front
Sound can be heard only
from a few speakers and
not all six.
•
•
speakers (L/R) only. Select "PRO LOGIC II" by pressing
(Dolby Pro Logic II) on the remote control to use all six speakers.
Make sure that the DVD disc is 5.1-CH compatible.
If you set C, SL, and SR to NONE in the speaker mode in the
audio setup of the setup screen, no sound is heard from the
center speaker and the front left and right speakers. Set C, SL,
and SR to SMALL.
Picture does not appear, sound • Was the Home Theater suddenly moved from a cold place to a
warm one? When condensation forms inside the player, remove
is not produced, or the disc
the disc and let the player stand for 1 or 2 hours with the power on.
tray opens 2 to 5 seconds later. (You can use the player again after condensation disappears.)
69
• Is there "Dolby Digital 5.1 CH" mark on the disc? Dolby Digital
•
5.1 CH Surround Sound is produced only if the disc is recorded
with 5.1 channel sound.
Is the audio language correctly set to DOLBY DIGITAL 5.1-CH in
the information display?
Check/Remedy
• Is the TV power on?
• Are the video cables connected properly?
• Is the disc dirty or damaged?
• A poorly manufactured disc may not be playable.
• Is the remote control being operated within its operation range of
The remote control does
not work.
angle and distance?
• Are the batteries exhausted?
• Have you selected the mode(TV/DVD) functions of the remote
control (TV or DVD) correctly?
Audio language and subtitles do not work.
• Audio language and subtitles will not work for DVDs not contain-
Menu screen does not appear even
when the menu function is selected.
• Are you using a disc that does not contain menus?
Aspect ratio cannot be
changed.
• The main unit is not working.
(Example: The power goes out or
strange noise is heard.)
• The Home Theater is not
working normally.
ing them. And depending on the disc, they may work differently.
• You can play 16:9 DVDs in 16:9 WIDE mode, 4:3 LETTER BOX
mode, or 4:3 PAN SCAN mode, but 4:3 DVDs can be seen in 4:3
ratio only. Refer to the DVD disc jacket and then select the appropriate function.
• Turn off the power and hold the
button on the main unit for
longer than 5 seconds.
Using the RESET function will erase all stored settings.
Do not use this unless necessary.
• While “NO DISC” message appears on the display of main unit, hold
The password for rating
level has been forgotten.
Can't receive radio broadcast.
the main unit's
button for longer than 5 seconds. “INITIALIZE”
appears on the display and all settings will return to the default values.
• Press the POWER button.
Using the RESET function will erase all stored settings.
Do not use this unless necessary.
• Is the antenna connected properly?
• If the antenna's input signal is weak, install an external FM antenna
in an area with good reception.
70
MISCELLANEOUS
Dolby Digital 5.1 CH
Surround Sound is not produced.
• Disc is rotating but no picture is produced.
• Picture quality is poor and
picture is shaking.
• CD-ROMs and DVD-ROMs cannot be played on this Home
•
Sound is not produced.
Symptom
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 70
Cautions on Handling and Storing Discs
Language Code List
Small scratches on the disc may reduce sound and picture quality or cause skipping.
Be especially careful not to scratch discs when handling them.
Handling discs
Do not touch the playback side of the disc. Hold
the disc by the edges so that fingerprints will
not get on the surface.
Do not stick paper or tape on the disc.
Disc Storage
Keep in a cool ventilated area
Do not keep in
direct sunlight
Caution
Keep in a clean
Protection jacket.
Store vertically.
• Do not allow the discs to become contaminated with dirt.
• Do not load cracked or scratched discs.
Handling and Storing Discs
When you get fingerprints or dirt on the disc, clean it
with a mild detergent diluted in water and wipe with a
soft cloth.
• When cleaning, wipe gently from the inside to the outside of the disc.
• Condensation may form if warm air comes into contact with cold parts
Enter the appropriate code number for the initial settings “Disc Audio”, “Disc Subtitle”
and/or “Disc Menu” (See page 41).
Code
Language
Code
Language
Code
Language
Code
Language
1027
Afar
1181
Frisian
1334
Latvian, Lettish
1506
Slovenian
1028
Abkhazian
1183
Irish
1345
Malagasy
1507
Samoan
1032
Afrikaans
1186
Scots Gaelic
1347
Maori
1508
Shona
1039
Amharic
1194
Galician
1349
Macedonian
1509
Somali
1044
Arabic
1196
Guarani
1350
Malayalam
1511
Albanian
1045
Assamese
1203
Gujarati
1352
Mongolian
1512
Serbian
1051
Aymara
1209
Hausa
1353
Moldavian
1513
Siswati
1052
Azerbaijani
1217
Hindi
1356
Marathi
1514
Sesotho
1053
Bashkir
1226
Croatian
1357
Malay
1515
Sundanese
1057
Byelorussian
1229
Hungarian
1358
Maltese
1516
Swedish
1059
Bulgarian
1233
Armenian
1363
Burmese
1517
Swahili
1060
Bihari
1235
Interlingua
1365
Nauru
1521
Tamil
1069
Bislama
1239
Interlingue
1369
Nepali
1525
Tegulu
1066
Bengali; Bangla
1245
Inupiak
1376
Dutch
1527
Tajik
1067
Tibetan
1248
Indonesian
1379
Norwegian
1528
Thai
1070
Breton
1253
Icelandic
1393
Occitan
1529
Tigrinya
Turkmen
1079
Catalan
1254
Italian
1403
(Afan) Oromo
1531
1093
Corsican
1257
Hebrew
1408
Oriya
1532
Tagalog
1097
Czech
1261
Japanese
1417
Punjabi
1534
Setswana
1103
Welsh
1269
Yiddish
1428
Polish
1535
Tonga
1105
Danish
1283
Javanese
1435
Pashto, Pushto
1538
Turkish
1109
German
1287
Georgian
1436
Portuguese
1539
Tsonga
1130
Bhutani
1297
Kazakh
1463
Quechua
1540
Tatar
1142
Greek
1298
Greenlandic
1481
Rhaeto-Romance
1543
Twi
1144
English
1299
Cambodian
1482
Kirundi
1557
Ukrainian
1145
Esperanto
1300
Kannada
1483
Romanian
1564
Urdu
1149
Spanish
1301
Korean
1489
Russian
1572
Uzbek
1150
Estonian
1305
Kashmiri
1491
Kinyarwanda
1581
Vietnamese
1151
Basque
1307
Kurdish
1495
Sanskrit
1587
Volapuk
1157
Persian
1311
Kirghiz
1498
Sindhi
1613
Wolof
1165
Finnish
1313
Latin
1501
Sangro
1632
Xhosa
1166
Fiji
1326
Lingala
1502
Serbo-Croatian
1665
Yoruba
1171
Faeroese
1327
Laothian
1503
Singhalese
1684
Chinese
1174
French
1332
Lithuanian
1505
Slovak
1697
Zulu
inside the player. When condensation forms inside the player, the player may not operate correctly. If this occurs, remove the disc and let the
player stand for 1 or 2 hours with the power on.
71
72
MISCELLANEOUS
Note
GB
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 72
USB Host Feature Supported Products
Digital Camera
Product
Finepix-A340
Finepix-F810
Finepix-F610
Finepix-f450
Finepix S7000
Finepix A310
KD-310Z
Finecam SL300R
Finecam SL400R
Finecam S5R
Finecam Xt
Dimage-Z1
Dimage Z1
Dimage X21
Coolpix4200
Coolpix4300
Coolpix 2200
Coolpix 3500
Coolpix 3700
Coolpix 4100
Coolpix 5200
Stylus 410 digital
300-digital
U300
X-350
C-760
C-5060
X1
U-mini
Lumix-FZ20
DMC-FX7GD
Lumix LC33
LUMIX DMC-F1
Optio-S40
Optio-S50
Optio 33LF
Optio MX
Digimax-420
Digimax-400
Sora PDR-T30
Coolpix 5900
Coolpix S1
Coolpix 7600
DMC-FX7
Dimage Xt
AZ-1
Company
Fuji
Fuji
Fuji
Fuji
Fuji
Fuji
Konica
Kyocera
Kyocera
Kyocera
Kyocera
Minolta
Minolta
Minolta
Nikon
Nikon
Nikon
Nikon
Nikon
Nikon
Nikon
Olympus
Olympus
Olympus
Olympus
Olympus
Olympus
Olympus
Olympus
Panasonic
Panasonic
Panasonic
Panasonic
Pentax
Pentax
Pentax
Pentax
Samsung
Samsung
Toshiba
Nikon
Nikon
Nikon
Panasonic
Minolta
Olympus
USB Flash Disk
Type
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Product
Company
Cruzer Micro
Cruzer Mini
Cruzer Mini
SONY Micro Vault
FLEX DRIVE
AnyDrive
XTICK
Micro Mini
iFlash
LG
RiDATA
Sandisk
Sandisk
Sandisk
Sony
Serotech
A.L tech
LG
Iomega
Imation
XTICK(M)
EZDrive
Type
USB 2.0 USB Flash Drive 128M
USB 2.0 128M
USB 2.0 256M
USB 2.0 64MB
USB 2.0 32MB
USB 2.0 128MB
USB 2.0 128M
USB 2.0 128M
USB 2.0 64M
USB 2.0 64M
USB 2.0 64M
MP3 Player
Product
Creative MuVo NX128M
Iriver H320
YH-920
YP-T7
YP-MT6
YP-T6
YP-53
YP-ST5
YP-T5
YP-60
YP-780
YP-35
YP-55
iAUDIO U2
iAUDIO G3
iAudio M3
SI-M500L
H10
YP-T5 VB
YP-53
Company
Creative
Iriver
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Cowon
Cowon
Cowon
Sharp
Iriver
Samsung
Samsung
Product
Company
G
E
N
E
R
A
L
T
F U
N
M E
R
V
I
D
E
O
O
U
T
P
U
T
Front speaker output
Center speaker output
Rear speaker output
Subwoofer speaker output
Frequency range
S/N Ratio
Channel separation
Input sensitivity
80W
3.5Kg
430 x 65 x 351.5 mm
+5°C~+35°C
10% ~ 75%
10dB
60dB
0.5%
1.0Vp-p(75Ω load)
Compositive Video : 1.0Vp-p(75Ω load)
RGB Signal : 0.714Vp-p(75Ω load)
Y:1.0Vp-p(75Ω load)
Pr:0.70Vp-p(75Ω load)
Pb:0.70Vp-p(75Ω load)
80W x 2(3Ω)
80W(3Ω)
80W x 2(3Ω)
100W(3Ω)
20Hz~20KHz
75dB
60dB
(AUX)400mV
Power Consumption
60W
Weight
1.3Kg
Dimensions (W x H x D)
Operating Temperature Range
Operating Humidity Range
Output
Frequency range
S/N Ratio
66 x 249 x 165 MM
+5°C~ +35°C
10% ~ 75%
80W x 2(3Ω)
20Hz~20KHz
75dB
Power Consumption
Weight
Dimensions (W x H x D)
Operating Temperature Range
Operating Humidity Range
Usable Sensitivity
S/N Ratio
Distortion
Composite Video
Scart Jack
Component Video
Type
128 MB MP3 Player
20G HDD MP3 Player
20G HDD MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
HDD MP3 Player
256MB MP3 Player
MP3 Player
MP3 Player
256MB MP3 Player
Multi Card Reader
UNICORN
USB 2.0 Card Reader
Specifications
A
M
P
L
I
F
I
E
R
S
W
A
3
0
0
0
GB
Type
Unicorn
USB 2.0 7 IN 1 CARD READER UC-601R
Billionton(Taiwan) USB 2.0 Card Reader for SD/MMC/RS-MMC(3-in-1)
MISCELLANEOUS
USB External HDD
Product
CUTIE
MOMOBAY UX-2
73
Company
Serotech
Dvico
Type
POCKET HARD DISK DRIVE
USB 2.0
74
HT-WQ20(41~70) GB
2003.4.11
5:54 PM
Page 74
Memo
HT-WQ20
Speaker system
S
P
E
A
K
E
R
Impedance
Frequency range
Output sound pressure level
Rated input
Maximum input
Dimensions (W x H x D)
Weights
5.1ch speaker system
Subwoofer speaker
Front/Center/Rear speaker
3Ω
3Ω x 5
35Hz~160Hz
140Hz~20KHz
85dB/W/M
82dB/W/M
100W
80W
200W
160W
90 x 152x 90 mm
200 x 90 x 92 mm
Front/Rear 0.5 Kg/0.4 Kg
Center
0.6 Kg
Front/Rear
Center
175 x 320 x 381 mm
5.1 kg
HT- TWQ22
Speaker system
S
P
E
A
K
E
R
Impedance
Frequency range
Output sound pressure level
Rated input
Maximum input
Dimensions (W x H x D)
Weights
5.1ch speaker system
Subwoofer speaker
Front/Center/Rear speaker
3Ω
3Ω x 5
35Hz~160Hz
140Hz~20KHz
85dB/W/M
82dB/W/M
100W
80W
200W
160W
90 x 1045x 90 mm
90 x 152x 90 mm
Center
200 x 90 x 92 mm
Front/Rear 3 Kg/0.4 Kg
Center
0.6 Kg
Front
Rear
175 x 320 x 381 mm
5.1 kg
HT- TWQ25
Speaker system
S
P
E
A
K
E
R
Impedance
Frequency range
Output sound pressure level
Rated input
Maximum input
Dimensions (W x H x D)
Weights
75
5.1ch speaker system
Subwoofer speaker
Front/Center/Rear speaker
3Ω
3Ω x 5
35Hz~160Hz
140Hz~20KHz
85dB/W/M
82dB/W/M
100W
80W
200W
160W
90 x 1045x 90 mm
90 x 1045x 90 mm
Center
200 x 90 x 92 mm
Front/Rear 3 Kg/2.8 Kg
Center
0.6 Kg
Front
Rear
175 x 320 x 381 mm
5.1 kg