Epson BrightLink 455Wi%2b User's Guide

TM

BrightLink 455Wi+

Interactive Projector

User’s Guide

2

Important Safety Information

WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes.

Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.

WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small children to avoid any risk of suffocation.

Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.

Copyright Notice

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.

Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by

Seiko Epson Corporation.

Trademarks

Epson and Instant Off are registered trademarks, and Epson Exceed Your Vision is a registered logomark of Seiko

Epson Corporation.

E-TORL is a registered trademark, BrightLink and SizeWise are trademarks of Epson America, Inc.

Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

© 2010 Epson America, Inc.

12/10

CPD-28223R1

Contents

Welcome

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . 10

Getting More Information . . . . . . . . . . . . . . . . . . . . . . . 10

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Unpacking the Mounting Hardware. . . . . . . . . . . . . . . . . . . 12

Projector Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connection Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Projector Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . 15

Interactive Pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Projector Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Additional Components. . . . . . . . . . . . . . . . . . . . . . . . . 19

Optional Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Interactive Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

1

Connecting to Computers, USB Devices, and Other Equipment

. . . . . . . . . . . . . . . . . . . . . . . 21

Connecting to a Computer. . . . . . . . . . . . . . . . . . . . . . . . . . 22

Connecting to the VGA Computer Port . . . . . . . . . . . . 22

Connecting to the USB Port . . . . . . . . . . . . . . . . . . . . . 23

Connecting the USB Cable for the Interactive

Pen or Remote Mouse Control . . . . . . . . . . . . . . 25

Connecting an External Monitor . . . . . . . . . . . . . . . . . . 26

3

4

Connecting to Video Equipment . . . . . . . . . . . . . . . . . . . . . 27

Connecting a Composite Video Source . . . . . . . . . . . . . 27

Connecting an S-Video Source . . . . . . . . . . . . . . . . . . . 28

Connecting a Component Video Source . . . . . . . . . . . . 29

Connecting an RGB Video Source. . . . . . . . . . . . . . . . . 30

Playing Sound Through the Projector . . . . . . . . . . . . . . . . . 31

Playing Computer Audio . . . . . . . . . . . . . . . . . . . . . . . . 31

Playing Sound from Video Equipment . . . . . . . . . . . . . 32

Connecting a Microphone . . . . . . . . . . . . . . . . . . . . . . . 33

Connecting External Speakers . . . . . . . . . . . . . . . . . . . . 34

Connecting a Document Camera or Other USB Device . . . 35

2

Displaying and Adjusting the Image

. . . . . . . . 37

Turning the Projector On and Off . . . . . . . . . . . . . . . . . . . . 38

Using the Direct Power On Function . . . . . . . . . . . . . . 39

Shutting Down the Projector . . . . . . . . . . . . . . . . . . . . . 40

Selecting an Image Source . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Focusing the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Selecting the Color Mode . . . . . . . . . . . . . . . . . . . . . . . 43

Resizing Video Images . . . . . . . . . . . . . . . . . . . . . . . . . . 44

3

Using the Interactive Pen

. . . . . . . . . . . . . . . . . . . 45

Using the Easy Interactive Pen Driver . . . . . . . . . . . . . . . . . 46

Calibrating the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Using the Pen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Using Easy Interactive Tools . . . . . . . . . . . . . . . . . . . . . . . . 50

Using the Tools for Windows . . . . . . . . . . . . . . . . . . . . 50

Using the Tools for Mac OS X . . . . . . . . . . . . . . . . . . . 62

Using the Tablet PC Function . . . . . . . . . . . . . . . . . . . . . . . 72

4

Presenting With the Remote Control

. . . . . . . . 73

Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Controlling the Picture and Sound . . . . . . . . . . . . . . . . . . . . 74

Turning Off the Picture and Sound . . . . . . . . . . . . . . . . 74

Stopping Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Zooming In on Your Image . . . . . . . . . . . . . . . . . . . . . . 75

Controlling the Volume . . . . . . . . . . . . . . . . . . . . . . . . . 76

Displaying Patterns. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Assigning a Pattern to the User Button. . . . . . . . . . . . . . 77

Creating Your Own Pattern . . . . . . . . . . . . . . . . . . . . . . 77

Operating Your Computer With the Remote Control . . . . . 78

Highlighting Your Presentation . . . . . . . . . . . . . . . . . . . . . . 79

Using the Pointer Tool. . . . . . . . . . . . . . . . . . . . . . . . . . 79

Customizing the Pointer Tool . . . . . . . . . . . . . . . . . . . . 80

Presenting a Slideshow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Starting a Slideshow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Selecting Slideshow Display Options . . . . . . . . . . . . . . . 82

5

Using the Projector Menus

. . . . . . . . . . . . . . . . . . 83

Using the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . 85

Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Adjusting Signal Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Customizing Projector Features . . . . . . . . . . . . . . . . . . . . . . 89

Customizing Power and Operation. . . . . . . . . . . . . . . . . . . . 91

Using the Projector Security Features . . . . . . . . . . . . . . . . . . 93

Enabling Password Protection . . . . . . . . . . . . . . . . . . . . 94

Creating Your Own Startup Screen . . . . . . . . . . . . . . . . 96

Disabling the Projector’s Buttons . . . . . . . . . . . . . . . . . . 97

Using Security Locking . . . . . . . . . . . . . . . . . . . . . . . . . 98

5

6

6

Using the Projector on a Network

. . . . . . . . . . . 99

Connecting to a Wired Network . . . . . . . . . . . . . . . . . . . . 100

Installing the Optional Wireless LAN Module . . . . . . . . . . 103

Using Quick Wireless Connection . . . . . . . . . . . . . . . . . . . 105

Configuring Basic Settings . . . . . . . . . . . . . . . . . . . . . . . . . 105

Configuring a Wireless Connection . . . . . . . . . . . . . . . . . . 107

Configuring the Projector . . . . . . . . . . . . . . . . . . . . . . 108

Selecting Wireless Network Settings in Windows . . . . 110

Selecting Wireless Network Settings in Mac OS . . . . . 110

Using Wireless Security Options . . . . . . . . . . . . . . . . . . . . 111

Enabling WEP Encryption . . . . . . . . . . . . . . . . . . . . . 111

Enabling WPA Security . . . . . . . . . . . . . . . . . . . . . . . . 113

Enabling Data Encryption from

EasyMP Network Projection . . . . . . . . . . . . . . . 114

Using the EasyMP Software . . . . . . . . . . . . . . . . . . . . . . . . 115

Using Projector E-mail Alerts . . . . . . . . . . . . . . . . . . . . . . . 115

Using SNMP to Monitor the Projector . . . . . . . . . . . . . . . 117

Using a Browser to Control the Projector . . . . . . . . . . . . . . 118

Using Web Remote Control . . . . . . . . . . . . . . . . . . . . 120

7

Maintaining the Projector

. . . . . . . . . . . . . . . . . . 123

Cleaning the Projection Window . . . . . . . . . . . . . . . . . . . . 124

Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . 124

Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Replacing the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Resetting the Lamp Timer . . . . . . . . . . . . . . . . . . . . . . 131

Checking Lamp Usage . . . . . . . . . . . . . . . . . . . . . . . . . 131

Replacing the Pen Batteries . . . . . . . . . . . . . . . . . . . . . . . . 132

Replacing the Remote Control Batteries . . . . . . . . . . . . . . . 133

Transporting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . 134

8

Solving Problems

. . . . . . . . . . . . . . . . . . . . . . . . . . . 135

Using On-Screen Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

Checking Projector Status. . . . . . . . . . . . . . . . . . . . . . . . . . 137

What To Do When the Lights Flash . . . . . . . . . . . . . . 137

Solving Projector Operation Problems . . . . . . . . . . . . . . . . 139

Solving Problems With the Image or Sound . . . . . . . . . . . . 140

Solving Problems With the Interactive Pen. . . . . . . . . . . . . 148

Solving Password Problems. . . . . . . . . . . . . . . . . . . . . . . . . 151

Solving Network Problems . . . . . . . . . . . . . . . . . . . . . . . . . 151

Solving Problems With the Remote Control. . . . . . . . . . . . 154

Where To Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155

Internet Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155

Speak to a Support Representative . . . . . . . . . . . . . . . . 155

Purchase Supplies and Accessories . . . . . . . . . . . . . . . . 156

A

Technical Specifications

. . . . . . . . . . . . . . . . . . . . 157

B

Notices

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . 163

FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . 166

Latin America Limited Warranty . . . . . . . . . . . . . . . . . . . . 167

Software Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171

Index

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199

7

8

-

Welcome

T he BrightLink

™

455Wi+ is an easy-to-use, ultra short-throw projector that turns any wall into an interactive whiteboard. The projector can be wall-mounted above a whiteboard or other surface and project an image up to 96 inches (diagonal) in native WXGA format. You can use the interactive pen to operate your computer or write and draw on a virtual whiteboard.

■

■

■

The projector offers up to 2500 lumens of white and color light output (brightness). You can connect it to a wide range of computers, interactive whiteboards, and video sources. You can also project from a document camera, USB storage device, or over your network. With the optional wireless LAN module, you can project over a wireless network.

The BrightLink 455Wi+ includes these additional features:

■

Wall bracket (setting plate) and built-in slide plate for easy and inexpensive wall mounting

■

■

Battery-operated pen and software that turns any wall into an interactive whiteboard

8.5-second startup time and Instant Off

®

feature for fast setup and shut down

Closed captioning

12 watt speaker and microphone input

USB display for easy setup of Windows

®

and Macintosh

® computers

9

10

Welcome

■

■

■

■

Using Your Documentation

This manual contains all the information you need to set up and use your projector. Please follow these guidelines as you read through it:

Warnings must be followed carefully to avoid bodily injury.

Cautions must be observed to avoid damage to your equipment.

Notes contain important information about your projector.

Tips contain additional projection hints.

Getting More Information

Need quick steps for setting up your projector? Here’s where you can look for help:

■

Installation Guide

Provides detailed instructions on installing the projector using the wall mounting hardware included in the box.

■

Quick Guide

Provides all the information you need to install the software, use the interactive pen, and solve basic problems.

■

EasyMP Network Projection Operation Guide

Provides detailed instructions on using your projector in a network environment (PDF installed along with this manual from the projector CD).

■

EasyMP Monitor Operation Guide

Provides instructions on using the EasyMP Monitor software to manage projectors on a network. To view the guide, double-click the icon on your computer's desktop. To download the software, double-click the

Download EasyMP Monitor

icon on your computer’s desktop.

■

Built-in help system

Provides assistance for common problems. Available from the

? Help

button on the projector or the remote control. See

page 136 for details.

■ www.latin.epson.com

Download FAQs and e-mail your questions to Epson support.

(Site available only in Spanish and Portuguese.)

Warranty

Your projector comes with a basic warranty that lets you project with

confidence. For details, see “Latin America Limited Warranty” on page 167.

Unpacking the Projector

After unpacking the projector, make sure you have all these parts:

BrightLink

455Wi+ CD

Epson Projector

Software CD

Projector

Power cord

Security sticker

USB cable

Epson Projector

Software for Easy

Interactive Function CD

2 AA batteries

(for remote control)

Remote control

Interactive pen

2 AAA batteries

(for interactive pen

Welcome

11

12

Welcome

Unpacking the Mounting Hardware

After unpacking the setting plate and mounting hardware, make sure you have all these parts:

End cap

Wall plate

Wall mount (setting plate)

Wall plate cover

Hex wrenches

Installation template

Bolts

See the Installation Guide for instructions on mounting the projector on a wall. Save all packaging in case you need to ship the projector.

Always use the original packaging (or the equivalent) when you need

to send the projector to another location. See page 134 for

transportation instructions.

Projector Parts

Speaker

Control panel

Remote receiver

Cable cover

Air exhaust vent

Security cable attachment

Kensington security slot

Filter cover switch

Air filter

Lamp cover

Lamp cover screw

Air filter cover

Focus lever

Remote control receiver

Projection window

Interactive pen receiver

Wireless LAN module slot

Welcome

13

Base

Wall mounting slide plate


14

Welcome

Connection Panel

S-Video port

Video port

Audio in ports

Audio out port

Microphone jack

Computer1/

Component input and audio jack

AC power inlet

RS-232C port

Monitor out port

USB

USB

(TypeA) port

(TypeB) port

LAN port

Computer2/Component input and audio jack

Projector Control Panel

Source Search button

(searches for connected video sources)

Keystone button

(corrects screen shape)

Menu button

(displays projector menus)

Esc button

(exits menu items)

Power light

Power button

Help button

Lamp and

Temperature warning lights

Wide button

(increases image size

Tele button

(decreases image size)

Keystone button

(corrects screen shape)

Enter button

(selects menu items)

Interactive Pen

Battery indicator

Button

Battery compartment cover

Attachment for strap or cord (not included)

Welcome

15

16

Welcome

Remote Control

Power button

A/V Mute button (turns off image and audio)

Auto button (adjusts image size and position)

Aspect button

(changes screen size)

Page Up/Down buttons

®

(control PowerPoint slides; USB cable required)

E-Zoom +/– buttons

(zoom into image)

Menu button

(accesses projector menus)

Source Search and

Source buttons

(select image source)

Freeze button

(stops image)

User button (lets you assign function)

Color Mode button

(changes display mode)

Num button (activates number buttons)

Pointer button

(activates pointer tool)

Esc button

(exits menus)

Menu navigation

(arrow) buttons and Enter button

Projector Dimensions

Use the dimensions below to guide you in placing or installing the projector.

With slide plate

0.33 in. (8.3 mm)

0.22 in. (5.5 mm)

6.7 in.

(170 mm)

11.5 in. (292 mm)

19.0 in. (483 mm)

14.5 in.

(369 mm)

7.0 in.

(177 mm)

Welcome

17

Without slide plate

0.91 in. (23 mm)

6.1 in.

(155 mm)

14.5 in.

(369 mm)

Mounting screw holes

4.2 in.

(107 mm)

6.7 in.

(170 mm)

3.6 in.

(92 mm)

6.2 in. (157 mm) 6.3 in. (160 mm)

19.0 in. (483 mm)

6.5 in. (166 mm)

14.5 in.

(369 mm)

18

Welcome

Additional Components

Depending on how you plan to use the projector, you may need additional components:

■

■

■

■

To receive a component video signal from a DVD player or other video device, you’ll need a component-to-VGA video cable. You can purchase the ELPKC19 cable from an authorized Epson

reseller. See “Optional Accessories” on page 20.

To receive an S-Video signal, you’ll need an S-Video cable. One may be included with your video equipment, or you can purchase one from a computer or electronics dealer.

To receive an audio signal, you’ll need an RCA-type audio cable with two male plugs, or a stereo mini-jack audio adapter cable

(with red and white jacks on one end).

To connect a Macintosh that includes only a Mini DisplayPort or

Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector’s VGA video port.

Contact Apple for compatible adapter options.

Welcome

19

note

Availability varies by country.

Optional Accessories

To enhance your use of the projector, Epson offers the following optional accessories:

Product

Additional interactive pen

Replacement lamp

Replacement air filter set

Wireless LAN module*

Quick Wireless Connection USB key

Kensington security lock

DC-10s document camera

DC-11 document camera

Component-to-VGA video cable

Cable management system

* USB cable is still required for interactive use.

You can purchase accessories from an Epson authorized reseller. To find the nearest reseller, call your nearest Epson sales office as

described in “Where To Get Help” on page 155.

Part number

V12H442001

V13H010L57

V13H134A34

V12H306P11

V12H005M05

ELPSL01

ELPDC10S

V12H377020

ELPKC19

ELPCK01

Interactive Table

The BrightLink 455Wi+ can be mounted at a 90-degree downward angle to create an interactive workspace directly on a table surface.

This is ideal for interactive group projects or lessons. For more information, visit one of the following: www.epson.com/bl455table

20

Welcome

Connecting to Computers,

USB Devices, and Other

Equipment

T his chapter tells you how to connect the projector to a notebook or desktop computer or to video equipment, such as a VCR, DVD player, or video camera.

You can also connect the projector to a USB storage device or document camera.

■

■

■

■

■

Follow the instructions in this chapter on:

Connecting to a computer

Connecting an external monitor

Connecting to video equipment

Playing sound through the projector

Connecting to a document camera or other USB device

1

21

note

If you have an iBook with an RCA video-out port, follow the instructions for connecting to a video device

on page 27.

Connecting to a Computer

You can connect the projector to any computer that has a standard video output (monitor) port. This connection is recommended for use with the interactive pen. See the next section for instructions.

You can also connect the projector to a computer using the projector’s

TypeB

(square) USB port, including desktop models,

PC notebook computers, MacBook ® computers, and other devices.

To play sound through the projector, connect an audio cable (see

page 31).

You may be able to use your remote control as a wireless mouse when

projecting from a computer (see page 78).

note

To connect a Macintosh that includes only a Mini

DisplayPort or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector’s VGA video port. Contact Apple for compatible adapter options.

Connecting to the VGA Computer Port

You can connect to the projector using a VGA computer cable, which you can purchase from a computer or electronics store. This is the best type of connection for use with the interactive pen.

1. Connect one end of the VGA computer cable to the projector’s

Computer1

or

Computer2 port and the other end to your computer’s monitor port.

Computer1 port

caution

Don’t try to force a connector to fit a port with a different shape or number of pins. You may damage the port or connector, or the device you are trying to connect.

Computer2 port

2. You may need to change the

Input Signal setting in the projector’s Signal menu to

RGB or

Auto

(see page 88).

22


3. You can connect an optional stereo mini-jack audio cable to play

sound through the projector (see page 31) or connect a

microphone (see page 33).

4. You may also be able to use the remote control as a wireless mouse

(see page 78).

When you’ve finished making connections, see page 38 for

instructions on turning on the projector and page 41 for instructions

on displaying and adjusting the image. For instructions on using the

interactive pen, see page 45.

Connecting to the USB Port

You can connect a Windows or Macintosh computer to the projector’s

TypeB

(square) USB port and project your computer’s display. This feature supports the following operating systems: 32-bit versions of Windows 7, Windows Vista

®

, Windows

XP, Windows 2000 (SP4), or Mac OS

®

10.5.1 or later.

A USB 2.0 connection (recommended) provides better picture quality and response than USB 1.1.

The first time you connect a computer to the projector’s USB port, software from the projector is installed on your computer.

1. Follow the instructions beginning on page 38 to turn on the

projector.

2. Make sure the

USB Type B

setting on the Extended menu is set to

USB Display

(see page 91).

3. Turn on your computer.


23

4. Connect the square end of the USB cable to the projector’s

TypeB

USB port.

note

If the software does not install automatically, you can install it manually. See

page 139 for instructions.

5. Connect the flat end of the cable to any available USB port on your notebook or desktop computer.

Messages appear on your computer screen as the projector is recognized and the software is installed automatically.

6. In Windows, if the AutoPlay window appears, click

EMP UDs.exe

.

On Mac OS, double-click the

USB Display Installer

icon to install the software.

7. Follow the instructions on the screen to install the Epson USB

Display software. If you see a “Digital Signature Warning,” select

Continue

or

Continue Anyway

. (You see these instructions only the first time you connect.)

After the software is installed, you see your computer’s current desktop displayed by the projector. You can switch the projector to other image sources using the

Source Search

button on the remote control or the projector.

24


8. You can connect an optional audio cable if you want to play

sound through the projector (see page 31).

When you’ve finished making connections, see page 41 for

instructions on displaying and adjusting the image.

9. When you’re done projecting, do one of the following:

Windows: simply disconnect the USB cable.

Mac OS: click the

USB Display

icon on the Dock and drag it to the trash, then remove the USB cable.

Connecting the USB Cable for the Interactive

Pen or Remote Mouse Control

In order to use the interactive pen, you must connect the USB cable to the projector and your computer.

Connecting the USB cable also lets you use the projector’s remote control as a wireless mouse. You can control your computer and click through slideshow-style presentations, such as PowerPoint, from up to

19.7 feet (6 meters) away (see page 78 for more information).

1. Connect the square end of the USB cable to the projector’s

TypeB

USB port.


25

2. Connect the flat end of the cable to any available USB port on your notebook or desktop computer. A USB 2.0 port is recommended for the best performance.

3. Set the

USB Type B

setting in the projector’s Extended menu to

Wireless Mouse

(see page 92).

4. Press the

Computer

button on the remote control to select your computer as the source. (The wireless mouse function doesn’t work when other sources are selected.)

5. If necessary, configure your computer to work with a USB mouse.

See your computer documentation for details.

note

Some LCD monitors may not be able to display the image correctly. If you have trouble displaying the image, connect a multiscan monitor. If you’re projecting computer images, make sure the computer’s refresh rate is set to 65 Hz or greater.

The projector must be turned on for the Monitor

Out port to send a signal to the monitor (though it may be in standby mode). Make sure Standby Mode is set to

Communication On

in the Extended menu. See

page 91.

Connecting an External Monitor

If you want to view your computer presentation close-up (on a monitor) as well as on the screen, you can connect an external monitor. You can use it to check on your presentation even if you’ve pressed the

A/V Mute

button or switched to a different picture source.

Only computer images will appear on the external monitor, not video images.

First make sure your computer’s VGA cable is connected to the projector’s

Computer1

port (see page 25). Then connect your

monitor to the projector’s

Monitor Out

port, as shown:

26


Connecting to Video Equipment

You can connect several video sources to the projector at the same time. Before starting, look at your video equipment to determine its available video output connections:

■

■

■

If your video player has a yellow RCA video output connector, see

“Connecting a Composite Video Source” on page 27.

If your video player has an S-Video connector, see “Connecting an S-Video Source” on page 28.

If your video player has a component video port (three connectors

labeled either Y/Cb/Cr or Y/Pb/Pr), see “Connecting a

Component Video Source” on page 29.

■

If your video player has an RGB video port, see “Connecting an

RGB Video Source” on page 30.

After connecting video cables, you may also want to connect an

optional audio cable to play sound through the projector; see page 31.

Connecting a Composite Video Source

1. If your video cable has an RCA connector, connect it to the yellow video output connector on your player and the yellow

Video

port on the projector.

Video port

note

If the video cable was not provided with your video device, you can purchase one from an electronics dealer.

2. If you want to play sound through the projector, see page 31 for

instructions on connecting an audio cable.


27

3. When you’ve finished making connections, see page 38 for

instructions on turning on the projector and page 41 for


Once the projector is turned on, select the image source by pressing the

Source Search

button on the projector or remote control.

Connecting an S-Video Source

1. Connect the S-Video cable to the S-Video connector on your player and the

S-Video


S-Video port







Source Search


28


Connecting a Component Video Source

If your video equipment has component video connectors (three connectors labeled either Y/Cb/Cr or Y/Pb/Pr), you will need a component-to-VGA video cable or a component video cable and adapter. You can purchase component-to-VGA cable (ELPKC19)

from an authorized Epson reseller (see page 20) or an electronics

dealer.

1. Connect the component end of the cable (3 male RCA) to the color-coded Y/Cb/Cr (or Y/Pb/Pr) connectors on your player.

2. Connect the other end of the cable (HD15 male) to the blue

Computer1 or

Computer2 port on the projector.

Connect componentto-VGA cable

Component-to-

VGA cable

(ELPKC19)

Connect componentto-VGA cable


Input Signal setting in the projector’s Signal menu to

Auto

(see page 88).







Source Search



29

Connecting an RGB Video Source

You can connect to an RGB video source using a VGA computer cable, which you can purchase from a computer or electronics store.

1. Connect the cable to the RGB video port on your player and the

Computer1

or

Computer2 port on the projector.

Connect to RGB video source

Connect to RGB video source


Input Signal

setting in the projector’s Signal menu to

RGB

(see page 88).


instructions on connecting audio cables.





Source Search


30


Playing Sound Through the Projector

You can play sound through the projector’s speaker system or attach an external speaker system. You can also connect a microphone and output sound through the projector.

You can use the or

Volume

buttons on the remote control to adjust the volume.

You can use the projector’s Extended menu to select a specific audio input source, or to enable audio output when the projector is in

standby mode. See page 92 for more information.

Playing Computer Audio

For laptop and most desktop computers, use a 3.5 mm stereo mini-jack cable, which you can purchase from a computer or electronics store.

1. Connect one end of the cable to the

Audio1

or

Audio2 jack on the projector.

Audio jacks

2. Connect the other end to your laptop’s headphone jack or audio-out jack, or your computer’s speaker or audio-out port.


31

note

If you are using a component-to-VGA cable, you will need to connect an audio adapter to use the

Audio1 or Audio2 jack.

Playing Sound from Video Equipment

For video equipment, use an RCA-style audio cable, which you can purchase from an electronics store.

1. Connect the red and white plugs on one end of the cable to the

L and

R Audio

jacks on the projector.

Connect to audio-out ports for video equipment

2. Connect the red and white plugs on the other end to the corresponding color-coded audio output jacks on your video source.

32


Connecting a Microphone

You can connect a dynamic microphone to the projector’s

Mic

port, using a 3.5 mm mini-jack cable as shown below.

Use the

Mic Input Level option on the Settings menu to adjust the

volume. See page 90 for more information.


33

Connecting External Speakers

You can output sound from the projector to external speakers with a built-in amplifier.

1. Locate the appropriate cable to connect your speakers.

Depending on your speakers, you may be able to use a standard audio cable with a stereo mini-jack connector on one end and pin jacks on the other end. For some speakers, you may need a special cable or adapter.

2. Connect the stereo mini-jack end of the audio cable to the

Audio

Out


Audio cable

3. Connect the other end of the cable to your speakers.

The projector’s internal speaker system is disabled while sound is output to external speakers.

34


Connecting a Document Camera or

Other USB Device

You can connect an interactive whiteboard, document camera, USB thumb (flash memory) drive, USB hard drive, or multimedia storage viewer, such as the Epson P-7000. You can use the projector’s

Slideshow function to display JPEG images or a presentation. See

page 80 for details.

Use the USB cable specified for your device.

1. Follow the instructions beginning on page 38 to turn on the

projector.

2. Connect the USB drive or the flat end of the USB cable to the

TypeA

(flat) USB port on the projector, as shown.

note

Use a cable less than 10 feet

(3 meters) long and connect the camera or other device directly to the projector.

Your projector may not function correctly if you use a longer cable or connect to a USB hub.

If you connect a USB hard drive, make sure you use the

AC adapter to power the hard drive. Make sure the file format is FAT 16/32.

Some USB hard drives may not be supported.

Connecting the Epson document camera

Indicator light

3. Connect the other end of the cable to your camera or other device, if necessary.

The indicator light on the projector turns orange and then green when a USB device is connected.

note

If the USB light turns red, the device may not be supported.


35

4. If the projector is connected to a storage device (and not connected to another image source), the Slideshow program appears.

If you are connected to another image source, press the

USB button on the remote control to go to the Slideshow program.

5. See page 80 for instructions on controlling the slideshow.

6. When you’re finished, press

Esc

and select

Exit

to exit the

Slideshow before turning off or removing the USB device.

Be sure to turn off your USB device (if necessary) before you remove the device or cable from the projector. Failure to do so may damage the device and/or the projector.

36



W hether you’re projecting from a computer or video equipment, you need to follow some basic steps to display your image on the screen.

■

■

■

Follow the guidelines in this chapter for:

Turning the projector on and off

Selecting the image source

Adjusting the image

2

37

Turning the Projector On and Off

Turn on any connected computer or video equipment before starting the projector so it can automatically detect and display the image source. If you turn on the projector first, or have multiple pieces of connected equipment, you may have to select the image source

manually (see page 41).

Follow these steps to turn on the projector:

1. Make sure the power cord is connected and the projector is plugged into an electrical outlet.

The Ppower light should be orange.

Power light

38


2. Press the Ppower button on the projector or on the remote control.

The projector beeps once and the Ppower light flashes green as the projector warms up, then an image begins to appear. When the Ppower light stops flashing and remains green, the projector is ready for use.

3. If you are prompted to enter a password, see page 95.

warning

Never look into the lens when the lamp is on. This can damage your eyes, and is especially dangerous for children.

Using the Direct Power On Function

The Direct Power On function enables faster setup. The projector starts up automatically when you plug it in or turn it on with a wall switch. You don’t have to press the Ppower button.

Follow these steps to enable Direct Power On:

1. Press the

Menu

button on the remote control or projector, then select the

Extended

menu and press

Enter

.

2. Choose

Operation

and press

Enter

.

3. Choose

Direct Power On

and press

Enter

.

note

If a power outage occurs when Direct Power On is enabled and the projector is plugged in, the projector will restart when the power is restored.

4. Highlight

On

and press

Enter

.

5. Press

Menu

to exit. The setting will take effect the next time you plug the projector into a power outlet or turn it on with a wall switch.


39

note

Lamp life will vary depending upon mode selected, environmental conditions, and usage.

Turn off this product when not in use to prolong the life of the projector.

You can set the projector to automatically turn off the lamp and enter “sleep mode” when it has not received any signals for 1 to 30 minutes

(see page 92). This conserves

electricity, cools the projector, and extends the life of the lamp. If you want to start projecting again,

press the P power button.

Shutting Down the Projector

This projector incorporates Instant Off technology. To turn it off, you can press its Ppower button as described below, unplug it, or turn off a power switch that supplies power to the projector. You don’t have to wait for the projector to cool down first.

1. To turn off the projector, press the Ppower button on the remote control or projector.

You see a confirmation message.

(If you don’t want to turn it off, press any other button.)

2. Press the Ppower button again. The projection lamp turns off and the projector beeps twice. You can then unplug the power cord.

If you want to turn the projector on again, make sure the orange

P power light is not flashing, then press the Ppower button.

40


Selecting an Image Source

You may need to select the image source if you have multiple image sources connected to the projector (such as a computer or DVD player). Selecting the image source lets you switch between images input from different pieces of connected equipment.

If you don’t see the image you want, press the

Source Search

button on the remote control or the projector until you see the image you want to project. Or, press one of the Source buttons on the remote control (

Computer

,

Video

,

USB

, or

LAN

).


Source buttons

If you still can’t see an image or can’t project the same image that is on

your notebook or computer screen, see page 140 for solutions.

Select

USB to project from a USB device or

LAN

to project over a

network. See page 80 for instructions.

■

■

■

■

Adjusting the Image

Once you see your image, you may need to make certain adjustments:

To focus the image, see page 42.

To quickly adjust the color, brightness, or contrast, see page 43.

To change the image aspect ratio, see page 44.

If you need to fine-tune the image and/or sound, see “Using the

Projector Menus” on page 83.


41

Focusing the Image

Focusing the projector is part of the installation process. If necessary, you can re-adjust the focus at any time using the focus lever next to the air filter on the side of the projector.

1. Slide the switch to open the air filter cover on the side of the projector.

2. Raise or lower the focus lever to sharpen the image.

Air filter cover switch

Focus lever

42


Selecting the Color Mode

The Color Mode adjusts the brightness, contrast, and color for various common viewing environments. Use this setting to quickly obtain a good picture.

Press the

Color Mode

button on the remote control to select an option. Press it until the option you want is projected in the upper right corner.

Color Mode button

■

■

Select from one of these

Color Mode

options:

■

■

Dynamic:

Brightest mode; for video games or TV in a bright room

.

Presentation:

For color presentations in a bright room (default setting).

Theatre:

For natural-toned movies in a darkened room.

Photo:

For vivid, high-contrast still images in a bright room (only available when the source is set to

LAN or

USB)

.

■

■

■

■

Sports:

For vivid TV images in a bright room (only available for component video, S-Video, or composite video sources).

sRGB:

Matches the color palette of standard sRGB computer displays.

Blackboard

: Projects accurate colors on a green chalkboard

(adjusts the white point).

Whiteboard

: For computer presentations in a bright room with black-and-white text and graphics.


43

note

You cannot change the aspect ratio when displaying from a computer using the

USB

TypeB

port or from a

USB device using the

USB

source.

Resizing Video Images

You can resize your images by changing the aspect (width to height) ratio (depending on your input signal).

Press the

Aspect

button on the remote control. Press the

Aspect button repeatedly to cycle through the available options.

Aspect button

Select from one of these

Aspect

options:

■

Normal:

Displays images using the full projection area and maintains the aspect ratio of the image. Choose this setting to automatically resize the image and make the best use of the display area.

■

■

16:9:

Converts the aspect ratio of the image to 16:9. 4:3 ratio images are elongated horizontally to fit.

Full:

Displays images using the full width of the projection area, but does not retain the aspect ratio. 4:3 ratio images are elongated horizontally.

■

■

Zoom:

Displays images using the full width of the projection area and maintains the aspect ratio of the image. The image may be cut off on the top and bottom depending on its aspect ratio.

Native:

Displays images as is (aspect ratio and resolution are maintained). Black bands may appear or images may be cut off, depending on the resolution.

If you are using the interactive pen, you will have to recalibrate after changing the projector’s aspect setting.

44



T he interactive pen included with your projector turn almost any wall into an interactive whiteboard. This chapter tells you how to use the Easy Interactive Driver software, calibrate the projector, and use the pen to annotate presentations or write and draw on a virtual whiteboard.

Follow the instructions in this chapter on:

■

Using the Easy Interactive Pen Driver

■

Calibrating the projector

■

Using the pen

■

Using the Easy Interactive Tools

■

Using the Tablet PC function

Periodically, it’s a good idea to check Epson’s support website at

www.latin.epson.com/proyectores for free updates to your Easy

Interactive software. (Site available only in Spanish and Portuguese).

3

45

46


Using the Easy Interactive Pen Driver

The Easy Interactive Driver software is included on the CD labeled

“Epson Projector Software for Easy Interactive Function.” Note the following system requirements:

■

Microsoft ® Windows 2000, Windows XP, Windows Vista (32-bit versions) or Windows 7 (32-bit and 64-bit) or

Mac OS X 10.3 or above

■

USB 1.1 port (minimum) or USB 2.0 port (recommended)

1. Connect a VGA computer cable and USB cable to the projector

and computer, as described on pages 22 and 25.

2. Turn on your computer.

3. Make sure the driver software is installed on your computer, as described in the Quick Guide.

4. Turn on the projector, as described on page 38.

■

■

You should see your computer desktop displayed. If you see a blank screen or the

No signal

message, check the following:

■

Make sure the power light on the projector is green and not flashing.

Press the

Computer

button on the remote control.

If you’re using a Windows laptop, press the function key on your keyboard that lets you display on an external monitor. It may be labelled

CRT/LCD

or have an icon such as may need to hold down the

Fn

key while pressing it.

. You

If you need more help, see page 142.

5. Check the connection status.

Windows: you should see the pen icon in the system tray on your taskbar (lower right corner of your screen).

Mac OS: you should see the pen icon in the Dock.

You may need to wait a minute for the icon to appear after you turn on the computer and projector.

If a red

X

appears on the icon, the computer and projector are not connected correctly. Try removing and reconnecting the USB cable.

If you don’t see the icon, do one of the following:

Windows: select or

Start

>

All Programs

or

Programs

>

Epson Projector

>

Easy Interactive Driver

.

Mac OS: open the Application folder, then select the

Easy

Interactive Driver

icon.

If you need more help, see page 148.

When the computer and projector are connected and the Easy

Interactive Driver icon is displayed, you’re ready to calibrate. See the next section for instructions.

note

Do not select

Exit

or

Quit

from the Easy Interactive

Driver menu. If you do, you will have to open the driver as described here the next time you want to use the interactive pen.

Calibrating the Projector

Calibration sets up the connection between your computer and the interactive pen. This simple process ensures that your computer can accurately detect the position of the pen on the projection surface.

You need to calibrate before using the pen for the first time, or if you change the resolution on your computer or connect a different computer.

Two types of calibration are available:

■

Normal, which is faster and appropriate for most situations (25 calibration points)

■

■

Advanced, which is recommended when you need higher accuracy (49 calibration points)

You may need to recalibrate if you change the projector’s aspect ratio using the remote control, or if you change the following settings in the projector’s menu system:

Settings menu:

Keystone

or

Zoom

. See page 89 for more

information.


47

note

For the most accurate calibration, make sure you hold the pen at an angle to the projection surface and touch the center of the circle.

■

Signal menu:

Auto Setup

,

Resolution

,

Tracking

,

Sync

,

Position

, or

Aspect

. See page 87 for more information.

1. To start calibration, do one of the following:

■

■

In Windows, click the pen icon in the system tray on your taskbar (lower right corner of your screen), then select

Calibrate (Normal)

or

Calibrate (Advanced)

.

In Mac OS, click the pen icon in the Dock, select

Calibrate from the menu bar, then select

Calibrate (Normal) or

Calibrate (Advanced)

.

2. After you read the message about calibration, click

OK

.

You see a flashing green circle in the upper left corner of your projected image.

3. Touch the center of the circle with the tip of the pen.

The circle stops flashing and turns black. You see another circle on the right.

4. Touch the center of the next circle, then repeat. When you get to the end of the row, the next circle appears at the left edge of a new row.

Make sure you are not blocking the signal between the pen and the interactive receiver (next to the projection window on the projector)

Don’t press the button on the pen while calibrating.

If you make a mistake, press

Esc

on your computer keyboard and restart the calibration process.

48


5. Continue until all of the circles are black.

After you have finished calibration, you can use either pen as a mouse on the projection board or wall. With additional software, you can also use the pen to write or draw on the projected image. See the next section for more information.

Using the Pen

The Easy Interactive Driver allows you to use the pen as a mouse. If you installed interactive whiteboard software you can also use the pen to write or draw on the projected image.

Battery indicator light

Button

■

■

Press the button on the pen to test the battery. If the indicator light is green, the battery has enough power.

Follow these tips to use the pen as a mouse:

■

For best performance, hold the pen at an angle, rather than perpendicular to the board.

To left-click, tap on the board.

To double-click, tap twice.


49

■

■

To right-click, tap while pressing the button on the pen.

To click and drag, tap and drag with the pen.

To use the pen for writing or drawing on the board, you need to install annotation software.You can use your own interactive whiteboard software or Easy Interactive Tools. To download and install Easy Interactive Tools, double click the

Download Easy

Interactive Tools

on your desktop.

Using Easy Interactive Tools

With Easy Interactive Tools, you can use the pen to write or draw on the projection surface. Make sure you installed the software, as described in the Quick Guide.

note

The Easy Interactive Tools are not required for using the interactive features of the projector. You can use any other interactive whiteboard software.

Using the Tools for Windows

Two different toolbars are available, one for interactive mode and one for whiteboard mode: Interactive Mode and Whiteboard Mode.

Additional whiteboard toolbar

Interactive toolbar

Whiteboard toolbars

■ Interactive Mode:

In interactive mode, the toolbar appears on the projected image and lets you use the pen as a mouse to open applications, access links, and operate scroll bars, for example.

50


■

In this mode, you can also annotate whatever is displayed from your computer and save your annotations.

Whiteboard Mode:

In whiteboard mode, the toolbar appears on a blank white surface. You can write or draw with the pen, add images, and save or print your pages.

1. To start Easy Interactive Tools, select or

Start

>

All

Programs

or

Programs

>

EPSON Projector

>

Easy

Interactive Tools

.

When Easy Interactive Tools opens, it is in interactive mode by default.

2. To toggle between interactive and whiteboard modes, select the

or icon in the upper right corner of the toolbar.

3. To exit, select the Easy Interactive Tools icon on the

Windows taskbar and select

Exit

.


51

Using Interactive Mouse Mode

When you first open Easy Interactive Tools, you are in interactive mode. Either the pen or mouse is active in this mode, as indicated by the icon in the upper left corner of the toolbar. When you see the mouse icon on the toolbar, you can use the pen as a mouse to select other tools.

Toggle between mouse and pen modes

Toggle between interactive and whiteboard modes

Page up and down

Draw on screen

(see page 55)

Undo

Use on-screen keyboard

Hide part of screen

Clear all annotations

Capture current screen

Create spotlight effect

Minimize the toolbar

The following interactive tools are available:

Interactive tools

Icon Description

Page up or down in a browser or other software program.

Use an on-screen keyboard to enter text on a website or in

a browser or other software program. See page 59 for

more information.

Capture the current screen and save it as an image file. See

page 59 for more information.

52


Interactive tools


Hide part of the screen. You can use the yellow arrows to reveal only the portions of the screen that you want the

audience to see. See page 55 for more information.

Create a spotlight effect for highlighting and shading part of the screen. You can move the spotlight and change its

shape, color, and transparency, as described on page 54.

Use the pen to right-click without pressing the button.

Minimize the toolbar. When the toolbar is minimized, you can restore it by selecting the Easy Interactive Tools icon on the Windows taskbar.

Entering Text

You can enter text in a browser or other program, such as a word processor or spreadsheet.

1. Open your internet browser or other program.

2. Select the keyboard tool. You see the on-screen keyboard:

3. Tap on the projected image where you want to enter text.

4. Select the letters and numbers on the on-screen keyboard.


53

Using the Spotlight Tool

To hide most of your projected image and reveal only a particular area, select the spotlight tool.

■

■

■

To resize the revealed area, tap and drag on the edge of the spotlight circle.

To move the revealed area, tap and drag outside the spotlight circle.

To adjust the revealed area, select the icon on the spotlight screen. You see the following window, which lets you adjust the shape of the revealed area, and the color and transparency of the hidden area.

Open a color-selection screen

Reset back to default color

Slide to adjust transparency of the hidden area

■ To remove the spotlight, select the icon on the spotlight screen.

54


Using the Shade Tool

To hide the projected image with an opaque shade and reveal only the area you want, select the shade tool. You see the following on the projected image:

■

■

To adjust the shade, tap and drag one of the yellow arrows.

To remove the shade, select the

Close

button on the screen.

Using Interactive Pen Mode

To switch to interactive pen mode, select any of the drawing tools on the toolbar. Or, select the mouse icon in the upper left corner.

The mouse changes into a pen.

The following annotation and drawing tools are available.

Drawing tools


Write or draw with a semi-transparent highlighter.

Toggle between writing/drawing and erasing. In the erase mode, you can select a free-form or straight line eraser, or circular and rectangular shapes for erasing in large swaths.

Select line width and color (basic/fast).

Customize line width and color (advanced/accurate).


55

Drawing tools


Write or draw free-form lines (or use free-form eraser).

Draw straight lines (or use straight-line eraser)

Draw circles or ellipses (or use circle eraser).

Draw rectangles or squares (or use rectangle eraser).

Undo the last annotation.

Clear all annotations.

Changing the Line Width and Color of the Pen

You can select the line width and color for the highlighter and drawing tools. Two types of selection windows are available, basic and advanced.

■

Select the icon to open the basic line adjustment window, as shown below:

Sample of selected line width

Select from

7 line widths

Select from

44 colors

56


■

Select the icon to open the advanced line adjustment window, as shown below:

Select a color value on the color wheel

Slide the red mark to select line width

Select specific RGB values to create a precise color

Use the slider to adjust the color brightness

Using Whiteboard Mode

To switch to a white screen that you can use as an interactive whiteboard, select the whiteboard icon.

You see the whiteboard tools, as shown below. Select the icon to display the additional tools.

Switch to interactive mode

View list of saved pages

Additional tools

Print preview

Print

Clear annotations

Open background image or previously saved page

Create new page

Save current page(s)

Delete current page

Select background

Copy previous page to current page

Display additional tools


57

Some of the tools are the same as those available in interactive mode.

Following is a list of the tools that are unique to whiteboard mode:

Whiteboard tools

View a list of saved pages in the current folder.

Switch back to interactive mode.

Delete the current page and display the previously saved page.

Insert a picture as the whiteboard background or open a previously saved page. You can select any image file in the

JPEG or BMP format.

Select a background. Tap the button repeatedly to choose from six solid colors, two styles of writing lines, or music staffs.

Create a new page on the whiteboard.

Copy the contents of the previously displayed page and paste it on the current page.

Undo the last operation.

Redo the last operation.

Save the current page as an image file. See the next section for more information.

Display additional tools.

Print preview.

Print all whiteboard pages in the current folder.

58


Saving Your Pages

You can save both whiteboard pages and computer screen images with annotations. You can also choose where you want to save your pages and in what format.

1. Select the icon in your taskbar

(lower right-hand corner of the screen) to open the Easy Interactive

Tools menu:

2. Select

Saving Setting

.

You see the on-screen keyboard and a file saving window:

3. Select or create the folder where you want to save your pages. You can use the on-screen keyboard to enter a file name prefix and select either

Jpeg

or

BMP

as the file type.

4. Select

Save

. You return to Easy Interactive Tools.

5. Do one of the following to save your pages:


59

60


■

In interactive mode, select the camera icon to capture the current screen and annotations. You see a message confirming that the screen is saved. Easy Interactive Tools adds the time and date to the file name prefix you selected, for example:

TEST010-11-29-13-23-3 month prefix year hour seconds minutes day

■

In whiteboard mode, select the save icon. The on-screen keyboard appears and a Save as window opens. You can select a location for saving and enter a name to create a new folder.

Your pages are automatically saved as numbered images.

Printing Your Pages

Once your pages have been saved, you can print them.

1. To display thumbnail images of the pages saved in the current folder, select the pages icon. You see the pages on the side of the screen:

2. To print your pages, select the icon to display additional tools. Then select the printer icon. You see the print window:

Select print settings.

Select the pages you want to print.

3. Select the pages you want to print, then select

OK

.


61

note

The Easy Interactive Tools are not required for using the interactive features of the projector. You can use any other interactive whiteboard software.

Using the Tools for Mac OS X

You can use the tools in two different modes: interactive (transparent background) and whiteboard (white background).

■ In interactive mode, the toolbox appears on the projected image and lets you annotate whatever is displayed from your computer.

You can also use the pen as a mouse to open applications, access links, and operate scroll bars, for example.

■ In whiteboard mode, the toolbox appears on a blank white surface. You can write or draw with the pen and save your pages.

1. To start Easy Interactive Tools, select

Applications

>

Easy

Interactive Tools Easy Interactive Tools

. You see the toolbox on your desktop, as shown below.

2. To quit, select the Easy Interactive Tools menu and select

Quit

Easy Interactive Tools

.

62


Using Interactive Mode (Transparent Background)

When you first open Easy Interactive Tools, you are in interactive pen mode, which lets you use your interactive pen to draw or annotate on the applications or images on the screen. You see the toolbox:

Hide toolbox

Draw free-form lines

Draw straight lines

Type text

Use the on-screen keyboard

Draw circles

Erase

Clear all annotations

Select interactive mouse mode

Save the current page

Draw rectangles

Set rectangle and circle style: bordered, filled, or both

Set line width

Set line color

(upper box)

Set fill color

(lower box)

The following tools are available:

Mac OS X tools


Write or draw free-form lines.

Erase individual annotations.

Draw straight lines.

Clear all annotations.

Open the text input box. See page 66 for more information.

Switch to interactive mouse mode. The arrow turns white, indicating that you can use the pencil tool as a mouse.

Open the on-screen keyboard.

Save the current page. See page 70 for more information.

Draw circles or ellipses.

Draw squares or rectangles.

note

To switch to interactive mouse mode, select the black arrow on the toolbar.

The arrow turns white, indicating interactive mouse mode.


63

Mac OS X tools

Select outline-only circles or rectangles.

Select filled circles or rectangles.

Select outlined and filled circles or rectangles.

Tap and drag the slider to select the line width for circles, rectangles, lines, and the eraser. This also affects the font size of the text you enter into the text input box.

Select the line color (upper box) and fill color (lower box) for

circles, rectangles, and lines. See page 68 for more

information.

To access additional options, select the

Tools

menu on the Mac OS X menu bar:

■

■

■

■

To switch to semi-transparent drawing tools, select

Highlighter

Pen

. Lines, circles, squares, and text input all become semi-transparent.

To switch to whiteboard mode, select

White Background

. For

more information, see page 70.

To save the current screen, select

Save Screen.

This works the same as selecting the

tool. For more information, see page 70.

To hide the toolbox, select the

X

in the upper left corner of the toolbox. To re-display the toolbox, open the Tools menu and select

Show Toolbox

.

64


Entering Text

You can enter text on the screen or in a browser or other program, such as a word processor or spreadsheet.

1. If necessary, select the black arrow on the toolbox to change it to a white arrow. This lets you use the pen as a mouse.

2. Open your internet browser or other program.

3. Select the keyboard tool in the toolbox. You see the on-screen keyboard:

4. Tap in the screen field where you want to enter text.

5. Select the letters and numbers on the on-screen keyboard. Select the caps lock key to enter capital letters.

If the keyboard does not appear, you may need to follow these steps to activate it:

1. Open the Apple menu and select

System Preferences

.

2. Select

Language & Text

, then select the

Input Sources tab.

3. Select

Keyboard & Character Viewer

or

Keyboard Viewer

, then scroll down if necessary and select your country and/or language. Make sure you select the

Show Input menu in menu bar

checkbox at the bottom of the screen.

4. When you want to use the on-screen keyboard, select the Input menu (flag icon) on the right side of the menu bar, then select

Show Keyboard Viewer

.

note

If the keyboard does not appear, you may need to follow these steps to activate it.


65

Using the Text Input Box

You can use the text input box to enter text for searching, dictionary lookup, or pronunciation.

1. To open the text input box, select the type tool, then tap on the board. The text input dialog box opens:

Use the on-screen keyboard

2. To open the on-screen keyboard, select the keyboard tool in the text input box.

3. Select letters and numbers on the on-screen keyboard.

4. Highlight the text and press the button on the pen to bring up a menu as shown below:

66


■

■

Use the options on the upper part of the menu to search on the text, look it up in a dictionary, or cut, copy, and paste it.

Use the options on the lower part of the menu to change the font, check spelling and grammar, or change the capitalization of the text.

■ To have the words spoken aloud, select

Speech > Start

Speaking

. The words in the dialog box are spoken aloud.

5. When you’re done entering text, select the

Enter

button to place the text on the screen, or select

Cancel

to close the text input box.

Selecting Line Width and Graphics Style

To adjust the width of lines, use the tool in the toolbox. Drag the slider to the right to increase the line width. This affects straight lines, free-form lines, circles, squares, and rectangles.

You can also select from three styles for circles and rectangles:

■

■

■

Select , then select the or tool to draw an outlined circle or rectangle.

Select , then select the or tool to draw a solid-color circle or rectangle.

Select , then select the or tool to draw an outlined and filled or solid-color circle or rectangle.

note

The default color and size of the text is determined by the selected Line Width and

Color settings. You can change the text properties by pressing the button on the pen and selecting

Font

>

Show Fonts

.


67

Defining Line and Fill Color

Several color selection dialog boxes are available that allow you to set the color for lines and the fill area in circles or rectangles.

Line color

Select the upper color box in the toolbox to set the line color or the lower box to set the fill color. You see the following Colors dialog box:

Color palettes

Slider

Spectrum

Fill color

Crayon box

Color bar

Move the slider to select darker colors

Indicates selected color

Tap anywhere on the circle to change the color

Save colors by dragging them here

After you select a color that you like, you can drag it from the color bar at the top to one of the squares at the bottom of the dialog box.

This allows you to save favorite colors for later use. More squares are available; you can save up to 300 colors.

68


To display the following alternate color selection dialog boxes, click the icons at the top of the screen.

Slider

Color palettes

Spectrum

Crayon box


69

Using Whiteboard Mode (White Background)

You can switch to a white screen that you can use as an interactive whiteboard.

1. Select the

Tools

menu on the Mac OS X menu bar:

2. Select

White Background

. You see the same tools defined on

page 63, but on a white screen.

3. To switch back to Interactive mode, open the

Tools

menu and select

Transparent Background

.

Saving Your Pages

You can select the location and format for saving your annotated images and pages.

1. Open the Easy Interactive Tools menu and select

Preferences..

..

You see the preferences dialog box:

70


2. Use the on-screen keyboard if you want to enter a different file name prefix for your saved pages; then select

Choose

if you want to change the location for saving.

3. Select

PNG

,

JPEG

, or

Windows BMP

as the file format for your saved pages.

4. When you want to save a page, select the camera tool. You see a message like the following:

Your captured screen image is saved in the location you selected, with an automatically generated filename based on the current date and time, for example: image20101005132629 prefix year month day hour seconds minutes

5. Select

OK

to confirm.


71

72


Using the Tablet PC Function

When you install the Easy Interactive Driver, the Tablet PC function is enabled in Windows 7 and Windows Vista. This allows you to annotate, use handwriting input, and perform other actions using the pen, even without installing annotation software.

If you have Microsoft Office 2003 or later, you can also use the Ink function in Office applications. This lets you add handwritten notes to a document, spreadsheet, or presentation, and save the notes with the file.

For more information about the Tablet PC and Ink functions, visit

Epson’s support website and select your product. (Site only available in Spanish and Portuguese).

Presenting With the Remote

Control

T he projector includes a number of tools to enhance your presentation. All of them can be accessed using the remote control, which lets you operate the projector from anywhere in the room—up to 19.7 feet (6 meters) away.

■

■

■

■

■

■

This chapter covers:

Using the remote control

Controlling the picture and sound

Displaying Patterns

Operating your computer with the remote control

Highlighting your presentation

Presenting a slideshow from a USB device

4

73

note

If a button is stuck down for longer than 30 seconds, the remote control stops operating to conserve battery power. When you release the button, normal operation resumes.

Using the remote control under bright fluorescent lamps or in direct sunlight may affect projector response.

■

■

■

Using the Remote Control

Make sure batteries are installed as described on page 133. Follow

these tips for using the remote control:

Point the remote control at the projector or at the screen.

Stand within 19.7 feet (6 meters) of the projector.

Aim the remote control within 30° to the side of, or 15° above or below, the remote control receivers on the projector.

Controlling the Picture and Sound

You can use the remote control to temporarily turn off the picture and sound, freeze the action, zoom in on the picture, and adjust the volume.

Turning Off the Picture and Sound

Press the

A/V Mute

button on the remote control to turn off the image and sound, and darken your screen. This is useful if you want to temporarily re-direct your audience’s attention without the distraction of a bright screen.

A/V Mute button

To turn the image and sound back on, press the button again.

You can create an image, such as a company logo or picture, to display on the screen whenever you press the

A/V Mute

button. (See page 96

for more information.)

74


Stopping Action

Press the

Freeze

button on the remote control to stop the action in your video or computer image. The image freezes but the sound continues.

To restart the action, press the

Freeze

button again.

Freeze button

note

The Freeze function pauses the image, not the sound.

Because the source continues to transmit signals, it will not resume at the same point.

Zooming In on Your Image

You can zoom in on a portion of the image using the

E-Zoom

buttons on the remote control.

If you are using the interactive pen, the pen position and mouse position will not match when you press the

E-Zoom

buttons.

1. Press the

E-Zoom + button on the remote control.

note

You cannot use the

Progressive

feature (see

page 87) while you are using

E-Zoom.

E-Zoom + button

You see a crosshair indicating the center of the zoom-in area.

2. Use the arrow (menu navigation) buttons to position the crosshair.

3. Continue pressing the

E-Zoom + button to enlarge the selected area up to 4 times.


75

note

To temporarily shut off the sound and picture, press the

A/V Mute

button.

4. While the image is enlarged, you can:

■

Use the arrow buttons to move around the screen.

■

Press the

E-Zoom – button to zoom out.

5. Press the

E

SC

button to return the image to its original size.

Controlling the Volume

To change the volume on the projector, press the or button on the remote control.

Volume buttons

You can also adjust the volume using the projector’s menu system.

See page 89.

Displaying Patterns

You can display a test pattern or one of the following 4 patterns for use on a whiteboard or chalkboard:

Pattern 1 Pattern 2

Pattern 3

Pattern 4

1. Press the

Menu

button on the remote control, then select the

Settings

menu and press

Enter

.

2. Highlight

Pattern

and press

Enter

.

3. Highlight

Pattern Type

and press

Enter

.

76


4. Select one of the patterns shown on page 76, or choose

Test

Pattern

. If you want to create your own pattern, choose

User

Pattern

. See below for more information.

5. Press

Enter

to select the pattern you want, then press

Esc

.

6. Choose

Pattern Display

to display the pattern.

7. Press

Esc

when you’re finished displaying the pattern.

Assigning a Pattern to the User Button

You can assign any of the available patterns to the

User

button on the remote control, and then display it by simply pressing the

User button.

1. In the Settings menu, select the

Pattern Type

as described on

page 76.

2. Highlight

User Button

and press

Enter

.

3. Highlight

Pattern Display

and press

Enter

.

4. Press

Menu

to exit.

Creating Your Own Pattern

You can transfer any image from your computer or video source to the projector and then use it as a pattern. If you assign it to the

User button as described above, you can display it any time you want by simply pressing the

User


Start by displaying the image you want to use from a computer or other source. Then follow these steps to capture the image and transfer it to the projector:

1. In the Settings menu, highlight

Pattern and press

Enter

.

2. Select

User Pattern

and press

Enter

.

3. When you see a message asking if you want to use the current image as the pattern, select

Yes

and press

Enter

.

4. Press

Enter

again.

note

When you choose an image for the user pattern, it erases any previously used image.


77

5. When you see a confirmation message, select

Yes

and press

Enter

. Saving the image may take a few moments. Do not use your projector, remote control, or video source while the pattern is being saved.

6. When you see a message that saving is complete, press

Menu

to exit.

note

You can use the remote control as a wireless mouse only when projecting from the

Computer1

or

Computer2

ports.

You may need to select specific settings on your computer to use the remote control as a mouse. See your computer documentation for details.

Operating Your Computer With the

Remote Control

You can use the remote control in place of your computer’s mouse so you won’t have to stand next to the computer to control the presentation.

Before you can use the remote control to operate your computer, you must connect a USB cable to the

TypeB on

the projector (see page 23) and select

Wireless Mouse

as the

USB Type B

setting on the Extended menu (see page 91).

Page up or down to change slides in PowerPoint

Right-click

Left-click

78


■

■

Then you can control your computer as follows:

■

Use the remote control’s

Page Up

or

Page Down

buttons to move through presentation slides.

Use the arrow buttons to move the cursor on the screen.

Press the

Enter

button once to left-click, or twice to double-click.

Press the

Esc

button to right-click.

■

To drag-and-drop, hold down the

Enter

button. Then use the arrow buttons to drag the object. When it’s where you want it, release the

Enter

button.

note

You can use the

Page Up/Page Down feature with USB Display.

Highlighting Your Presentation

You can display a pointer to call out important information on the screen. If you want to customize the pointer tool, you can choose from three alternative shapes.

Using the Pointer Tool

1. To activate the pointer tool, press the

Pointer

button on the remote control. A pointer appears on the screen.

Pointer button

If you prefer to use a different style of pointer, see the instructions in the next section.

2. Use the arrow buttons on the remote control to position the pointer on the screen.

3. When you’re done using the pointer, press the

Pointer

or

Esc button to clear the screen.


79

Customizing the Pointer Tool

You can change the appearance of the pointer by choosing from three alternative shapes.

1. Press the

Menu

button on the remote control, highlight the

Settings menu, highlight

Pointer Shape

, and press

Enter

. You can select one of the pointer shapes shown at the left.

2. Select the shape you want and press

Enter

.

3. Press

Menu to exit from the menu system.

note

You can project .JPG files in resolutions up to

4608 × 3072, with pixel counts incrementing in multiples of 8.

If a .JPG file is highly compressed, your projector may not be able to display it correctly. The projector can’t display progressive or

CMYK .JPG files.

You cannot project movie files using the Slideshow feature.

Presenting a Slideshow

You can use your projector’s Slideshow feature whenever you connect a USB device that contains image files having a .JPG filename extension. This lets you quickly and easily display individual images, or start a slideshow of all the images in a folder. You can control your slideshow using the projector remote control.

For an instant PowerPoint presentation, convert your PowerPoint slides to individual .JPG files (save as *.jpg) and store them in a folder.

Copy that folder to a USB flash memory drive (thumb drive), or other

USB device. Then connect the device to the projector and begin your presentation.

You can switch the display from the device displaying the slideshow to another source using the

Source Search

button or one of the specific source buttons on the remote control. To return to the Slideshow source, press

Source Search

and select

USB

, or simply press the

USB button.

Starting a Slideshow

1. Connect a USB device to the projector’s

TypeA

(flat) USB

port (see page 35).

2. If you are connected to another image source, press the

USB button on the remote control to go to the Slideshow program.

80


If you are not connected to another image source, the Slideshow program appears automatically.

Files for images that have been scanned or modified will display an icon, rather than a thumbnail image.

If necessary, press the arrow buttons on the remote control to highlight the device you want to present from, then press the

Enter

button.

3. If you need to select a subfolder on your device, press the arrow buttons to highlight the folder and press

Enter

.

4. To display an individual image, press the arrow buttons to highlight it and press

Enter

. To display additional image files, press the l or r arrow button.

5. To display a slideshow of all the images in the current folder, use the arrow buttons to highlight

Slideshow

on the bottom of the

Slideshow screen and press

Enter

. The images display sequentially one time through. At the end, you see the folder display again.

Select the following as necessary to control your display or slideshow:

■

To move back up a folder level, highlight

Back to Top

at the top of the Slideshow screen and press

Enter

.

■

To select a different device, highlight

Select drive in the upper right corner of the screen, press

Enter

, and select the device.

note

To rotate a displayed image,

press the u or d button on

the remote control until it is displayed correctly.

note

To display a slideshow from a folder that is not open, highlight the folder and press the

Esc

button on the remote control. Then select

Slideshow

from the menu that appears and press

Enter

.

To begin a slideshow from a particular image, use the arrow buttons to highlight that image, press

Enter

, then press

Enter

again.


81

■

■

If all the images in a folder do not fit on the Slideshow screen, highlight

Next page

at the bottom of the screen and press

Enter to display the next screen full of images. Select

Previous page

at the top of the screen to select the previous screen.

To exit the slideshow, press

Esc

, select

Exit

, and press

Enter

.

Selecting Slideshow Display Options

1. Highlight

Option

at the bottom left corner of the slideshow screen and press

Enter

. You see this screen:

2. Highlight the options you want to use, and press

Enter

.

Option

Display order

Sort order

Available settings

Name order displays files in name order

Date order displays files in date order

In Ascending sorts the files first to last

In Descending sorts the files last to first

Continuous play

On displays a slideshow continuously

Off displays a slideshow one time through

Screen switching time

No does not switch file display automatically

1Sec. to 60Sec. displays files for the selected time and switches them automatically

3. When you are finished, highlight

OK

at the bottom of the screen and press

Enter

. (Highlight

Cancel

and press

Enter

to cancel.)

82


■

■

■

■

■

■


Y ou can use the projector’s on-screen menus to adjust the image, sound, and other features. This chapter covers the following information:

Using the menu system

Adjusting the image

Adjusting signal settings

Customizing projector features

Customizing power and operation

Using the projector security features

5

83

Using the Menu System

You can use the remote control or the projector’s control panel to access the menus and change settings. Follow these steps:

1. To display the menu screen, press the

Menu

button on the remote control or on the projector. You see a menu screen similar to the one below:

Options

Menu list

The menus are listed on the left and the options available for the highlighted menu are shown on the right.

2. Use the arrow buttons on the remote control or the projector to scroll through the menu list. When you’ve highlighted the desired menu, press the

Enter

button to select it.

3. Once you’ve selected the menu, use the arrow buttons to scroll through the list of options. (Some of the options may be grayed out or unavailable, depending on the selected source.)

4. After highlighting the option you want to adjust, use the arrow buttons to change the setting. In some cases, you may have to press the

Enter

button to view a sub-screen.

■

■

Press the left or right arrow button to adjust a slider bar.

To select from two or more settings, press the up or down arrow button to highlight the setting and press

Enter

.

84


5. After changing the settings, press the

Esc

button to save your changes and return to the previous menu (or press it again to exit the menu system). You can also press the

Menu

button to exit.

Restoring the Default Settings

You can use the

Reset

option on any menu to restore the factory-default settings for the settings in that menu.

To restore all the projector settings to their factory-default values, select the

Reset

menu, highlight

Reset All

, press

Enter

, and select

Yes

to confirm.

note

When you select

Reset All

in the Reset menu, it does not reset the Input Signal,

User’s Logo, Language, or

Lamp Hours settings.

Adjusting the Image

You can use the Image menu to adjust the brightness, sharpness, color, tint, contrast, and

Auto Iris

settings.

1. Press the

Menu

button on the projector or remote control and select the

Image

menu. You see a screen similar to one of these:

Computer/USB/USB Display/LAN Component video/

Composite video/

S-Video


85

note

The available settings vary depending on the input source selected.

The

Brightness

setting changes the opacity of the projector’s LCD panels. You can also change the lamp’s brightness. Select

Power

Consumption

in the

Settings menu, then choose

Normal

or

ECO

(the default setting is

Normal

).

2. Adjust the desired options as needed:

■

■

Color Mode

Lets you quickly adjust the color and brightness for various environments. You can save a different setting for each

source. See page 43 for a description of each color mode.

Brightness

Lightens or darkens the overall image.

■

■

Contrast

Adjusts the difference between light and dark areas.

Color Saturation

Adjusts the color depth of the image.

■

■

■

■

Tint

Adjusts the balance of green to magenta in the image.

Sharpness

Adjusts the sharpness of the image.

Color Adjustment

Adjusts the color values. Select

Abs. Color Temp

. to adjust the overall value from 5000 °K (red) to 10000 °K (blue).

Select

Red

,

Green

,

Blue to adjust red, green, and blue hue and saturation values. (Not available if sRGB

is selected as the

Color Mode setting.)

Auto Iris

Automatically adjusts the projected luminance according to the brightness of the image. (Available only when

Dynamic or

Theater

is selected as the Color Mode for the current input source.)

86


Adjusting Signal Settings

Although the projector normally detects and optimizes the input signal automatically, you can use the Signal menu to make manual adjustments. In addition to changing the position of the projected image, you can correct tracking and sync for computer images, or change the aspect ratio.

1. Press the

Menu

button and select the

Signal

menu. You see a screen similar to one of those below. (The settings will be different depending on the source you are projecting from.)

Component video

Computer

Composite video/S-Video

2. Adjust the desired options as needed:

■ Auto Setup

Leave this setting

On to automatically optimize computer images. Turn it off if you want to save adjustments you have made to the Tracking, Sync, and Position settings.

■ Resolution

Set to

Auto

to have the projector automatically identify the resolution of the input signal. If necessary, select

Wide

(for widescreen images) or

Normal

(for 4:3 or 5:4 ratio images).

note

If you are using the interactive pen, you will have to recalibrate if you change any of these settings:

Auto Setup, Resolution,

Tracking, Sync, Position, or

Aspect.


87

note

You can also use the remote control’s

Auto

button to automatically reset the projector’s Tracking, Sync, and Position settings. See

page 146 for details.

■

■

■

■

■

■

■

■

Tracking

Adjust this value to eliminate vertical stripes in computer images.

Sync

Adjust this value if computer images appear blurry or flicker.

Position

If the image is slightly cut off on one or more sides, it may not be centered exactly. Select this setting and use the arrow buttons to center it.

Progressive

For composite video, S-Video, and component video. Turn this setting on to convert interlaced signals into progressive signals (best for moving images). Leave the setting

Off

for still images.

Noise Reduction

Smooths out rough images. You may need to experiment to select the best setting for your image. Select

Off

when viewing low-noise image sources, such as DVDs.

Input Signal

If the colors don’t look right on the

Auto

setting, select the setting for the type of equipment you’ve connected to the

Computer1

or

Computer2 port. Choose

RGB

for a computer or RGB-video connection, or

Auto

for a video player that outputs a component video signal (with connectors labeled Y/Cb/Cr or Y/Pb/Pr).

Video Signal

(composite or S-Video signals only)

Select the setting for the type of equipment you’ve connected to the

Video

port. Leave this setting at

Auto

unless you are using a 60-Hz PAL system (then select

PAL60

).

Aspect

Sets the image’s aspect ratio (ratio of width to height). See

page 44 for more information.

88


Customizing Projector Features

You can use the Settings menu to lock the buttons on the projector, adjust audio volume, and customize several other features.

■

■

■

■

■

■

Keystone

Adjusts the shape of the image if the projector has been tilted upward or downward. If you notice that lines or edge look jagged after adjustment, decrease the

Sharpness

setting (see page 85).

Zoom

Adjusts the image size from

Wide

(larger) to

Tele

(smaller).

Control Panel Lock

Lets you disable all of the buttons on the projector, or all of the

buttons except the Ppower button. See page 97 for more

information.

Pointer Shape

Lets you choose from three alternative pointer shapes. See page 79

for more information.

Power Consumption

Lets you select from two levels of brightness. The

ECO setting reduces power consumption and projector noise, and extends the lamp’s operating life.

Volume

Raises or lowers the volume of the projector’s speaker.

note

If you are using the interactive pen and you change the Keystone or

Zoom settings, you will have to recalibrate.


89

■

■

■

■

Mic Input Level

Adjusts the microphone volume.

Remote Receiver

Deactivates the projector’s front and/or rear sensors that detect signals from the remote control. Use this setting to prevent use of the remote control or to stop interference from bright fluorescent lights. Restart the projector for this setting to take effect.

User Button

Lets you create a shortcut to one of the following menu items:

Power Consumption

,

Info

,

Progressive

,

Closed Caption

,

Test Pattern

,

Resolution

,

Mic Input Level

, or

Pattern

Display

. When you press the

User

button on the remote control, the assigned menu item is displayed.

Pattern

Lets you select one of the following:

Pattern Display to display one of the available patterns.

Pattern Type to select from the following 4 patterns, or select a user-defined pattern:

Pattern 1 Pattern 2 Pattern 3 Pattern 4

User Pattern

to capture a customized pattern. See page 77 for

more information.

Test Pattern to display a pattern that you can use for adjusting the projector without connecting it (for a 16:10 image). You can use the pattern to adjust the zoom, focus, and other settings. To cancel the test pattern, press the

Esc


90


Customizing Power and Operation

You can use the Extended menu to customize the way the projector displays images, enable Direct Power On, use closed captioning, turn sleep mode on or off, and customize other projector operations.

■

■

■

■

Display

Messages:

Lets you turn screen messages on or off.

Display Background:

Sets the screen background to

Black

,

Blue

, or

Logo

when no image signal is available.

Startup Screen:

Enables or disables display of the startup (User’s

Logo) screen when the projector is turned on.

A/V Mute:

Sets the screen background to

Black

,

Blue

, or

Logo when the

A/V Mute

button is pressed.

Closed Caption

Lets you display closed captioning for content that provides it.

User’s Logo

Create a custom startup screen, as described on page 96.

Projection

Front/Ceiling:

Lets you project onto the front of a screen.

Rear/Ceiling:

Lets you project from behind onto a transparent screen.


91

note

If

Direct Power On

is enabled, the power cord is connected, and a power outage occurs, the projector will start when the power is restored.

note

Do not use the projector at altitudes above 7,500 feet

(2,286 meters).

■

■

■

Operation

Direct Power On:

Enable if you want to be able to start the projector when you connect the power cord (without pressing the

P power button).

Sleep Mode

: Enable if you want the projector to turn off automatically if it is idle and no signal is received for 1 to 30 minutes (you can adjust the amount of time using the next setting).

Sleep Mode Timer

: When Sleep Mode is on, you can set the period of time before the projector turns off automatically, from

1 to 30 minutes.

High Altitude Mode

: Enable when you are using the projector above 4,900 feet (1,500 meters) to ensure that the temperature is regulated properly. Turn this setting off for lower elevations.

Audio Input:

Select a specific audio input source or set to

Auto to support any input source.

Standby Setup

Standby Mode

: Select

Communication On

to enable the projector to be monitored and controlled from a computer when it is in standby mode (the power light is orange). This setting also allows you to use a microphone connected to the projector or to run audio through the projector in standby mode.

Standby Microphone

: Enable this setting to use a connected microphone when the projector is in standby mode.

Standby Audio

: Enable this setting to output audio when the projector is in standby mode.

USB Type B

Select how you want to use the

TypeB

(square) USB port.

Select

USB Display

to use the USB port to project computer images. Select

Wireless Mouse

to use the remote control

buttons like a wireless mouse. See page 78 for restrictions and

details.

92


■ Language

Select a language to use for the projector menus and messages. To change the language, press the

Menu

button on the remote control, highlight

Extended

and press

Enter

, select

Language and press

Enter

, then select your language and press

Enter

.

■

■

■

■

Using the Projector Security Features

To prevent unauthorized use of the projector, you can:

Assign a password. You can use the password to prevent the projector from being turned on and prevent your custom startup screen from being changed. See the next section.

Create a custom screen that is displayed at startup and/or when the

A/V Mute

button is pressed. The screen can be locked with a password to discourage theft and provides a way to identify the

projector should it be stolen. See page 96.

Disable the projector’s buttons; this is useful, for example, in a classroom when you want to ensure that no one touches the projector’s buttons while you’re using the remote control. See

page 97.

Secure the projector to prevent theft using a cable locking system.

See page 98.


93

caution

If you lose the remote control, you will not be able to enter the password. Keep the remote control in a safe place at all times. Also, it’s a good idea to write down your password.

Enabling Password Protection

The default setting for the password is

0000

. Follow these steps to create a new password:

1. Press the

Freeze

button on the remote control for five to seven seconds. You see this screen:

Hold down

2. Select the type(s) of password protection you want to use:

■

Power On Protect

: Prevents unauthorized use of the projector. After the projector is plugged in and turned on, you must enter a password to use the projector. Select

On

, press

Enter

, then press

Esc

to return to the Password Protect screen.

■

■

User’s Logo Protect

: Prevents your custom screen (see

page 96), display, and User’s Logo settings in the Extended

menu from being changed. Select

On

, press

Enter

, then press

Esc


Network Protect

: Prevents any of the network settings from being changed. Select

On

, press

Enter

, then press

Esc


3. Use the arrow buttons to select

Password

and press

Enter

.

4. When you see a message asking if you want to change the password, select

Yes

and press

Enter

.

5. Hold down the

Num

button and use the numeric keypad to enter a four digit password.

6. When you see a confirmation message, re-enter the password.

94


7. Press the

Menu

button, then press

Enter

to exit the screen.

8. Turn off and unplug the projector.

Starting the Projector With a Password

When the password function is enabled, you see this screen when you plug in and turn on the projector:

note

If you leave the projector plugged in, the Password screen will not appear. It appears only if you unplug and reconnect the power cord.

Hold down the

Num

button and use the numeric keypad to enter the four digit password.

The password screen closes and projection begins.

If projection does not begin, check the following:

■ If the password is not correct, you see a message prompting you to re-enter the password. If you enter an incorrect password three times in succession, you see an error code with the message

The projector’s operation will be locked and the projector switches to standby mode. Write down the error code, then disconnect the projector’s power cord from the electrical outlet, reconnect it, and turn the projector back on. Try entering the correct password again.

■

■

If you have forgotten the password, contact Epson with the request code number that appears in the Password screen for

assistance. See “Where To Get Help” on page 155.

If you enter an incorrect password 30 times in succession, the projector remains locked and you must contact Epson to arrange for service.


95

note

When you choose an image for the user’s logo, it erases any previously used image.

You can save an image up to

300 × 400 pixels in size.

Once you have saved a new user’s logo, you cannot return to the factory default logo.

Creating Your Own Startup Screen

You can transfer any image from your computer or video source to the projector and then use it as your startup screen. You can also use it as the screen displayed when the projector is not receiving a signal or when you press the

A/V Mute

button. The image can be a company logo, slogan, photograph, or any other image you want to use.

Capturing the Image

Start by displaying the image you want to use from either a computer or video source, such as a DVD player or digital camera. Then follow these steps to capture the image and transfer it to the projector:

1. Press the

Menu

button on the remote control, highlight the

Extended menu, and press

Enter

.

2. Highlight

User’s Logo

and press

Enter

.

3. When you see a message asking

Choose this image as the

User’s Logo?

, select

Yes

and press

Enter

. A selection box displays over the image.

4. Use the arrow buttons to select the area of the image you want to use. Then press

Enter

.

5. When you see the message

Select this image?

, highlight

Yes and press

Enter

.

6. Use the arrow buttons to select a zoom factor (display size) and press

Enter

.

96


7. When the message

Save this image as the User’s Logo?

appears, select

Yes

and press

Enter

. Saving the logo may take a few moments. Do not use your projector, remote control, or video source while the logo is being saved.

8. When you see the message

Completed

, press

Menu

to exit.

Choosing When to Display the Image

After your image is saved, you can set it to display as the startup screen, the screen you see when there’s no signal, or the screen you see when you press the

A/V Mute

button (see page 74).

1. Press the

Menu

button, highlight the

Extended menu, and press

Enter

.

2. Select

Display

and press

Enter

.

3. Choose from these display options:

■

■

Set

Display Background

to

Logo

to display your image when there is no signal.

Set

Startup Screen

to

On

to display your image when the projector is warming up.

■

Set

A/V Mute

to

Logo

to display your image when you press the

A/V Mute

button.


Menu

to exit.

note

You can lock these settings to prevent them from being changed without a password

(see page 94).

Disabling the Projector’s Buttons

When you enable the Control Panel Lock function, you can lock all of the projector’s buttons, or all of the buttons except the Ppower button. The remote control can still be used to operate the projector.

1. Press the

Menu

button, highlight the

Settings

menu, and press

Enter

.

2. Select

Control Panel Lock

and press the

Enter

button.


97

3. Select

Full Lock

(to lock all projector buttons) or

Partial Lock

(to lock all buttons except the Ppower button) and press

Enter

.

4. Select

Yes

and press

Enter

to confirm the setting.

5. Press the

Menu

button to exit.

To disable the Control Panel Lock function, select

Off

in the Control

Panel Lock menu. Or press and hold the

Enter

button on the projector’s control panel for seven seconds. A message is displayed and the lock is released.

Using Security Locking

The projector includes two security locking points to prevent its theft when installed or used in public locations:

■


. You can attach a commercially available security cable as shown below to secure the projector to the wall mount (setting plate).

Kensington security slot

Security cable attachment bar

■

Kensington security slot.

The security slot (located on the side of the projector) is compatible with the MicroSaver security systems manufactured by Kensington. You can purchase this lock

from Epson (see page 20).

98


note

If you want to use the interactive pen while projecting through a wired or wireless network, you must connect the USB cable from the projector to your computer.

Using the Projector on a

Network

T his chapter tells you how to prepare to send images to your projector through a wired or wireless network.

Using EasyMP Network Projection, you can project images shown on your computer screen—including text, graphics, and video—directly to your audience. See the EasyMP Network Projection Operation Guide for information on features and use.

You can use EasyMP Monitor (available for Windows only) to monitor and control your projector through the network. For information on installing and using EasyMP Monitor, see the EasyMP

Monitor Operation Guide.

You’ll find instructions in this chapter on:

■

Connecting the projector to a wired LAN

■

Installing the optional wireless LAN module

■

Using Quick Wireless Connection

■

Configuring projector and network settings

■

Using wireless security options

■

Sending e-mail alerts and monitoring the projector

■

Using a browser to control the projector

For wireless connection, make sure you’ve installed the optional

wireless LAN module, as described on page 103. Then follow the steps

in this chapter to use Quick Wireless Connection (Windows only) or configure your projector and network. See the EasyMP Network

6l

99

Projection Operation Guide for instructions on installing the software.

The guide also contains instructions on using the software to project over the network.

If you want to use the interactive pen while projecting through a wired or wireless network, you must set the

USB Type B

option to

Wireless Mouse

in the Extended menu. See page 92 for more

information.

Connecting to a Wired Network

With a shielded, Category-5 Ethernet cable, you can connect the projector to your network and configure it with an IP address. You can then project from multiple computers on your network without changing any cables.

1. Connect the projector to your network using a commercially available 100BaseTX or 10BaseT network cable. Connect the cable to the

LAN

port on the projector as shown.

Network cable

2. Connect the other end to your Ethernet hub or router.

3. Point the remote control at the projector and press the Ppower button.

100


4. Press the

LAN button on the remote control to select network as the source.

5. Press the

Menu

button on the remote control, select the

Network

menu, then press

Enter

.

6. Choose

Network Configuration

and press

Enter

.

7. Select the

Wired LAN

menu and press

Enter

.

8. Choose

IP Settings

and press

Enter

. You see a screen like the following:


101

9. Do one of the following:

■

If your network assigns addresses automatically, turn on the

DHCP

setting.

■

If your network does not assign addresses automatically, turn off

DHCP

and enter the projector’s

IP Address

,

Subnet

Mask

, and

Gateway Address

, as needed.

To enter numbers, use the arrow buttons on the remote control to select each number on the screen, then press the

Enter

button. When you’re finished entering an address in the network menu, highlight

Finish

, then press the

Enter button.

10. Press

Esc

to return to the previous menu.

11. To prevent the IP address from appearing on the standby screen, set the

IP Address Display

setting to

Off

.

12. When you’re done making these changes, press

Esc

, select

Complete

and press

Enter.

Then select

Yes

and press

Enter again to save your settings.

Press

Menu

to exit the menu system.

102


Installing the Optional Wireless LAN

Module

Make sure you have the optional Wireless LAN Module. Turn off the projector and disconnect the power cord before you install the module.

1. Open the air filter cover by sliding the switch and lifting the cover.


103

2. Insert the wireless LAN module as shown.

3. As a security feature, you can fasten the module using the screw that came with it.

Insert screw here

4. Close the air filter cover.

If you have the optional Quick Wireless Connection USB key

(V12H005M005), you can use Quick Wireless connection as described in the next section (Windows only). Or, you can configure

your connection manually as described on page 105.

104


Using Quick Wireless Connection

Using the optional Quick Wireless Connection USB key, you can connect the projector to a Windows computer wirelessly without any configuration.

First, make sure you have installed the wireless module as described on

page 103 and turned on the projector.

1. Connect the USB key to the projector’s port.

TypeA

(flat) USB

2. When you see a projected message that the network information update is complete, remove the USB key.

3. Connect the USB key to a USB port on your computer or notebook.

In Windows 7 or Windows Vista, if you see the AutoPlay window, select

Run LaunchU3.exe

. When you see the User

Account Control screen, click

Allow

.

4. Follow the instructions on the screen to install the Quick Wireless

Connection driver.

If you see a Windows Firewall message, click

Yes

to disable the firewall.

After a few moments, your computer image will be displayed through the projector. If not, try restarting your computer.

5. When you’re done with your presentation, remove the USB key.

You may need to restart your computer to reactivate your wireless interface.

note

Do not attempt to write to the USB key or use it as a flash memory drive.

note

The Quick Wireless

Connection utility will disable any other wireless sessions and adapter programs. Make sure you leave the USB key in your computer for your entire

Quick Wireless Connection session.

Configuring Basic Settings

You can give your projector a unique name, enable a projector keyword, or create a password for controlling the projector over the

Web.

1. Press the

Menu

button, then choose

Network

and press

Enter

.

2. Choose


and press

Enter

.


105

3. Choose

Basic

and press

Enter

. You see the following screen:

4. Make sure the projector has a unique name, so you can identify it on your network.

If you need to rename it, highlight the

Projector name

text box then press

Enter

.

5. Use the arrow buttons on the remote control to select individual letters; then press

Enter

to input a character. To navigate backward and forward through the input text, highlight the arrows and press

Enter

. To toggle symbol settings or capital letters, highlight the option and press

Enter

. (The only symbols available are the hyphen and underscore.) When you’re done, highlight

Finish

and press

Enter

.

6. If you want to create a password for using PJLink to control the projector, highlight

PJLink Password

, press

Enter

, and enter a password of up to 8 alphanumeric characters. When you’re done, highlight

Finish

and press

Enter

.

106


7. If you want to create a password for remote access to the projector, highlight

Web Control Password

, press

Enter

, and enter a password of up to 8 alphanumeric characters. When you’re done, highlight

Finish

and press

Enter

.

8. If you want to set up a security keyword so that only people who are in the same room as the projector can access it, turn

Projector keyword

on. Then when you want to connect to the projector, it displays a randomized four-digit number or “keyword” on the screen. If you’re using EasyMP Network Projection, you can enter the keyword on your computer to connect (see the EasyMP

Network Projection Operation Guide for details).

9. When you’re done making these settings, press

Esc

, choose

Complete

and press

Enter

, then choose

Yes

and press

Enter

to save your settings.

■

■

Configuring a Wireless Connection

After you install the optional wireless LAN module, you can use the

EasyMP Network Projection software to connect to the projector and send images wirelessly in two modes: Ad Hoc mode or Access Point mode.

Ad Hoc mode (computer-to-computer mode) lets you connect just one computer to the projector at a time; it’s easy to set up, and the only equipment you need is a computer with a wireless

(802.11g, 802.11b, or 802.11a) network card or adapter, or a

Macintosh with an AirPort ® or AirPort Extreme card. When you connect with this mode, any connection to other wireless networks is broken; you can connect to the projector only.

Access Point mode (infrastructure mode) lets multiple computers access the projector at the same time and easily trade off control over the projector. To use Access Point mode, you need a wireless

(802.11g, 802.11b, or 802.11a) access point or an AirPort

Extreme (or AirPort) base station, and one or more computers with wireless network cards or adapters.

note

Make sure you’ve installed the EasyMP Network

Projection software as

described in the EasyMP

Network Projection

Operation Guide.

To connect to the projector over a wireless network, your computer must be running

Windows 2000, XP, Vista, or Windows 7. Your Mac must be running Mac OS X

10.3 to 10.6.

Access Point mode

(infrastructure mode) is required to achieve transfer speeds up to 54MB/sec on an

802.11g network. Ad Hoc mode (computer-tocomputer mode) limits network connections to

11MB/sec. This is a standard specification of

802.11g networking.


107

Configuring the Projector

1. Press the

Menu

button, then choose

Network

and press

Enter

.

2. Choose


and press

Enter

.

3. Choose

Wireless LAN and press

Enter


4. Make sure Wireless LAN Power is set to

On

. You can turn it off to prevent unauthorized access.

5. Select one of the following connection modes:

■

Quick

mode lets you easily connect one computer to the projector at a time. You can also select this setting when you’re using the optional Epson Quick Wireless Connection

USB key.

■ Advanced mode lets multiple computers access the projector at the same time and easily trade off control of the projector.

This method requires a wireless network access point or an

AirPort Extreme (or AirPort) base station.

6. If your network is using 802.11a, use the arrow buttons on the remote control to highlight

802.11a

, then press

Enter

to select it.

Press

Esc


108


7. Highlight

SSID

, press

Enter

, and enter the name you want to assign to the projector (Quick mode), or the name of your existing wireless network (Advanced mode):

Use the arrow buttons to select individual letters; then press

Enter to input a character. To navigate backward and forward through the input text, highlight the arrows and press

Enter


Enter

. When you’re done, highlight

Finish

and press

Enter

.

Note that the SSID is case-sensitive (if you enter the name in uppercase on the projector, you must type it the same way on the computer connecting to the projector).

8. Select

IP Settings

and do one of the following:

■ If your network assigns addresses automatically, turn on the

DHCP

setting.

■ If your network does not assign addresses automatically, turn off

DHCP

and enter the projector’s

IP Address

,

Subnet

Mask

, and

Gateway Address

, as needed.


Enter

button. When you’re finished entering an address in the network menu, highlight

Finish

, then press the

Enter button.

9. If you want to prevent the SSID from being displayed on the standby screen, set the

SSID Display

option to

Off

.

10. To prevent the IP address from appearing on the standby screen, set the

IP Address Display

setting to

Off

. Press

Esc


note

For specific details about your network, please consult your network administrator.

If you’re using AirPort, start the AirPort Admin utility, select your base station and click

Configure

. Then click the Network tab to see your base station’s IP address.


109

note

Settings may vary, depending on your wireless network adapter. See the documentation for your adapter for more information.


Esc

. Choose

Complete

and press

Enter

, then choose

Yes

and press

Enter


Now you’re ready to select the wireless network your computer, as described below.

Selecting Wireless Network Settings in

Windows

Before connecting to the projector, select the correct wireless network on your computer.

1. To access your wireless utility software, double-click the network icon on the Windows taskbar.


■ If your projector is set up on an existing network (Advanced mode), select the network name (SSID).

■ If your projector is configured for Quick mode, select the

SSID you assigned to the projector.

3. Click

Connect

.

Now you’re ready to connect to the projector. See the EasyMP

Network Projection Operation Guide for details.

Selecting Wireless Network Settings in Mac OS

Before connecting to the projector, select the correct wireless network on your computer.

1. Click the AirPort icon on the menu bar at the top of the screen.

2. Make sure AirPort is turned on, then do one of the following:

■

■

If your projector is set up on an existing network (Advanced mode), select the network name (SSID).

If your projector is configured for Quick mode, select the

SSID you assigned to the projector.

110


Using Wireless Security Options

The projector includes WEP and WPA data encryption security options which you can enable for network projection.

Make sure the settings you select match the ones used by your network; follow the directions from your network administrator.

See the following sections to enable security options on your projector:

■

“Enabling WEP Encryption” below

■

“Enabling WPA Security” on page 113

You also need to enable security settings from EasyMP Network

Projection (see page 114).

Enabling WEP Encryption

1. Press

Menu

on the projector remote. Highlight

Network

and then press

Enter

.

2. Choose


and press

Enter

.

3. Highlight

Security

, then press

Enter


note

The authentication and firewall features are only effective when the access point for the connection destination supports the same functions.

4. Press

Enter

to select Security, then select

WEP and press

Enter

.

Press

Esc



111

note

Text input for WEP encryption varies with different access points; check with your network administrator. Try ASCII first. If that doesn’t work, try Text2 and then Text3.

5. For the WEP encryption setting, select

128Bit

or

64Bit

and press

Enter

. Press

Esc


6. For Format, highlight

ASCII

to enable text input or

HEX

to enable hexadecimal input, then press

Enter

. Press

Esc


7. If you chose

64Bit as WEP Encryption, choose

Encryption key

1

,

2

,

3

, or

4

. Press

Esc


Highlight the

Encryption key

that corresponds to the Key ID you selected, then press

Enter

. Use the arrow buttons to select individual letters; then press

Enter


Enter


Enter


Finish

and press

Enter

.

8. Check with your network administrator for directions on entering a key for your network, and follow these general guidelines:

■

For 128 bit WEP encryption with hexadecimal input, enter

26 characters, from 0 to 9 and from A to F.

■

■

For 64 bit WEP encryption with hexadecimal input, enter 10 characters, from 0 to 9 and from A to F.

For 128 bit WEP encryption with ASCII or text input, enter

13 alphanumeric characters.

■

For 64 bit WEP encryption with ASCII or text input, enter 5 alphanumeric characters.

9. For Authentication Type, select

Open

or

Shared

, depending on the setting your network uses. Press

Esc


112



Esc

. Choose

Complete

and press

Enter

, then choose

Yes

and press

Enter


Enabling WPA Security

1. Press

Menu

. Highlight

Network

and then press

Enter

.

2. Choose


and press

Enter

.

3. Highlight

Security

, then press

Enter


4. Press

Enter

to show the menu, then choose one of the following and press

Enter

.

■

WPA-PSK (TKIP)

■

WPA-PSK (AES)

■

WPA2-PSK (TKIP)

■

WPA2-PSK (AES)

5. Press

Esc

to return to the previous screen.


113

note

If the password is longer than 32 characters, enter it by accessing the projector from a web browser. This lets you enter up to 63

characters. See page 118 for

details.

6. Highlight the

PSK

(pre-shared key) and press

Enter

. Use the arrow buttons to select individual letters; then press

Enter


Enter


Enter


Finish

and press

Enter

.


Esc

. Choose

Complete

and press

Enter

, then choose

Yes

and press

Enter


Enabling Data Encryption from EasyMP

Network Projection

When using the EasyMP Network Projection software, follow these steps to enable data encryption.

1. Click

Set options

on the main screen.

2. Click the

General Settings

tab.

3. Select the

Encrypt communications

checkbox.

4. Click

OK

.

For more information, see the EasyMP Network Projection Operation

Guide.

114


■

■

■

■

■

Using the EasyMP Software

Once you’ve set up your projector and computer for network projection, see the EasyMP Network Projection Operation Guide for instructions on the following EasyMP features:

Starting EasyMP Network Projection

Projecting over the network (content over IP)

Multi-screen projection

Using Presentation mode

Connecting to a projector on a different subnet

Using Projector E-mail Alerts

When this feature is enabled, the projector sends you an e-mail alert if it has any problems.

1. Press the

Menu


Network

menu, then press

Enter

.

2. Choose


and press

Enter

.

3. Choose

Mail

, then press

Enter


4. Highlight

On to receive E-mail notifications, then press

Enter

.

Press

Esc



115

note

If a critical problem develops with a projector which causes it to suddenly stop working, it may not be possible for the projector to send a message.

If Standby Mode is set to

Communication ON

in the Extended menu, the projector can still be monitored even if the projector is in standby mode

(when the power is off).

5. Enter the IP address for the SMTP server for the projector.

You can enter a number from 0 to 255 in each field of the address.

However, the following IP addresses cannot be used: 127.x.x.x,

224.0.0.0 to 255.255.255.255 (where x is a number from 0 to

255).


Enter

button.

When you’re finished entering an address in the network menu, highlight

Finish

, then press the

Enter

button.

6. Enter the SMTP server’s port number. The default value is 25.

You can enter a numeric value from 1 to 65535.

7. Choose one of the

Address

fields and press

Enter

. Then enter the e-mail address and the contents of the message that you will receive when a problem or warning occurs. You can register up to three addresses. You can enter up to 32 alphanumeric characters for the e-mail address.


Esc

. Choose

Complete

and press

Enter

, then choose

Yes

and press

Enter


When the selected problem or warning occurs, an e-mail message is sent to the specified notification addresses. The subject line of the e-mail is

EPSON Projector

.

The e-mail includes the following information:

■

Line 1: The name of the projector where the problem has occurred

■

■

Line 2: The IP address of the projector where the problem has occurred

Line 3: Details of the problem

116


Using SNMP to Monitor the Projector

Network administrators can use SNMP (Simple Network

Management Protocol) to monitor projectors.

1. Press the

Menu


Network

menu, then press

Enter

.

2. Choose


and press

Enter

.

3. Choose

Others

, then press

Enter


note

If you’re a network administrator, you can use the SNMP option to enter a trap IP address. This lets you receive trap alerts for the projectors you’re monitoring.

4. Turn on the SNMP setting.

5. Enter up to two IP addresses for notification in the Trap IP

Address fields.

You can enter a number from 0 to 255 in each field of the address.

However, the following IP addresses cannot be used: 127.x.x.x,

224.0.0.0 to 255.255.255.255 (where x is a number from 0 to

255).


Enter

button.

When you’re finished entering an address in the network menu, highlight

Finish

, then press the

Enter

button.

6. For

Priority Gateway

, select

Wired

or

Wireless

. Press

Esc

to return to the previous screen.


117

7. If your network environment uses an AMX controller, select

ON to allow the projector to be detected by AMX Device Discovery.


Esc

. Choose

Complete

and press

Enter

, then choose

Yes

and press

Enter


Using a Browser to Control the Projector

You can use a standard web browser to monitor and control the projector through the network. Because you can use your computer’s keyboard, you may find it easier to make network settings using your browser than using the projector’s remote control.

1. Make sure the projector is set up for your network, as described

on page 100. (Standby Mode in the Extended menu should be set

to

Communication On

to monitor the projector in standby mode.) When using a browser to access the projector, you cannot connect through a proxy server.

2. Open your web browser and enter the IP address of the projector you want to monitor in the browser window.

If you’re not sure what the address of the projector is, turn the projector on and select

Net. Info.-Wired LAN

or

Net.

Info.-Wireless LAN

from the Network menu to display the IP address of the projector. Do not enter the leading zeroes.

118


3. Press

Enter

, or, if you set a Web control password in the projector’s Network menu, enter your user name and password, then press

Enter

. You see a screen like the following:

4. Select one of the menu options listed on the screen, then change any of the settings as needed. These settings correspond to those found in the projector’s menu system.

You cannot change the following settings using a web browser:

■

Pointer Shape

,

Pattern

, or

User Button in the Settings menu

■

■

■

User’s Logo

,

High Altitude Mode

, and

Language

in the

Extended menu

Reset All

and

Reset Lamp Hours

in the Reset menu

Password protection


119

Using Web Remote Control

When you access the projector through your browser, you can display a “virtual remote control” on your computer screen. This lets you change sources and perform many of the same functions as you can with the physical remote control.

From the Projector Control menu, select

Web Remote


Power button


Computer button

Video button

A/V Mute button

Pause button

Page-up/down buttons

LAN button

USB button

Volume buttons

Closed captioning button

■

■

■

■

■

■

■

The

Power

button turns the projector on and off.

The

Search

button searches for signal sources (see page 41).

The Computer button selects a computer signal (connected to the

Computer1

or

Computer2

port).

The Video button selects a video signal (connected to the

Video or

S-Video port).

The LAN button selects a network signal or wireless signal (using the optional wireless unit).

The USB button selects USB computer display (see page 23) or a

signal from equipment connected to the

TypeA

(flat)

port, such as a document camera (see page 35).

The Pause button stops the image (see page 75).

120


■

■

■

■

A/V Mute button temporarily turns off the picture and sound (see

page 74).

The Page Up/Down buttons control PowerPoint slides (requires

USB cable. See page 78).

The Volume buttons raise or lower the audio volume.

The

CC

(Closed Captioning) button lets you display closed captioning for content that provides it.


121

122


warning

Before you clean any part of the projector, turn it off and unplug the power cord.

Never open any cover on the projector, except the lamp cover. Dangerous electrical voltages in the projector can injure you severely. Do not try to service this product yourself, except as specifically

explained in this User’s

Guide. Refer all other

servicing to qualified service personnel.


Y our projector needs little maintenance. All you have to do on a regular basis is clean the lens, and check that the air filter and vents are clean. A clogged air filter or vent can block ventilation needed to cool the projector.

The only parts you should replace are the lamp and air filter. If any other part needs replacing, contact your dealer or a qualified servicer.

■

■

■

■

■

■

■

■

This chapter covers the following:

Cleaning the projection window

Cleaning the projector case

Cleaning the air filter

Replacing the air filter

Replacing the lamp

Replacing the pen batteries

Replacing the remote control batteries

Transporting the projector

7

123

caution

Do not rub the projection window with harsh materials or subject it to shocks, or you may damage the window.

Do not use wax, alcohol, benzene, paint thinner, or other chemical detergents.

These can damage the case.

Cleaning the Projection Window

Clean the projection window whenever you notice dirt or dust on the surface.

To remove dirt or smears on the window, use a commercially available cloth for cleaning glasses.

■

■

Cleaning the Projector Case

Before cleaning, turn off the projector and unplug the power cord.

To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth.

To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent and firmly wring the cloth dry. Then wipe the case.

124


Cleaning the Air Filter

Your projector includes an air filter to ensure the best performance and help protect your equipment investment. If dust collects on the air filter, clean it as described here. Dust clogs prevent proper ventilation and can cause overheating, which can damage the projector.

1. Turn off the projector.

2. Remove dust from the air filter using a small vacuum cleaner designed for computer or office equipment, or gently clean the vent with a soft brush (such as an artist’s paintbrush).

note

To order replacement air filters, request part number

V13H134A34. See page 20

for ordering information.

You can remove the air filter to clean both sides.

If the filter is too dirty or broken, replace the filter as described below.

■

■

■

Replacing the Air Filter

You need to replace the air filter if:

You cannot remove the dust from it

The air filter is damaged or torn

You repeatedly see a projected message telling you to clean or replace it


125

Contact your dealer or call Epson as described in “Where To Get

Help” on page 155 to obtain a new air filter. Request part number

V13H134A34.

1. Turn off the projector and unplug the power cord.

2. Slide the switch, then open the air filter cover on the side of the projector.

note

Air filters contain ABS resin and polyurethane foam.

Dispose of used air filters according to local regulations.

3. Grasp the tab and pull the air filter straight out as shown.

126


4. Press in the new air filter until it clicks into place.

Replacing the Lamp

The life span of the projection lamp is about 2500 hours if

Power

Consumption in the Settings menu is

Normal

(default), and 3500 hours if this setting is

ECO

. See page 131 to check the lamp usage.

■

■

It is time to replace the lamp when:

The projected image gets darker or starts to deteriorate.

The message

Replace the lamp appears on the screen and the

Lamp

light flashes orange. To maintain projector brightness and image quality, replace the lamp as soon as possible.

You may also need to replace the lamp if the

Lamp

light flashes

red. See page 137.

note


Contact your dealer or call Epson as described in “Where To Get

Help” on page 155. Request part number V13H010L57.


127

warning

Let the lamp cool fully before replacing it.

In the unlikely event that the lamp has broken, small glass fragments may be present and should be removed carefully to avoid injury. If the projector has been installed on the ceiling, you should stand to the side of the lamp cover, not underneath it.

If the lamp is used after the replacement period has passed, the possibility that the lamp may break increases. When a lamp replacement message appears, replace the lamp with a new one as soon as possible, even if it is still working.

Follow these steps to replace the lamp:

1. Turn off the projector and unplug the power cord.

2. Let the projector cool for at least an hour (if it has been on). The lamp is extremely hot immediately after use.

3. Loosen the lamp cover screw (you cannot remove it). Then slide the lamp cover off.

4. Loosen the two screws holding the lamp in place (you can’t remove them).

Loosen, but don’t remove these screws

128


5. Grasp the lamp handle as shown and pull it straight out.

note

The lamp(s) in this product contain mercury.

Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.

6. Gently insert the new lamp along the guide rail, then push it in place.


129

7. Tighten its screws, then press it in by the handle until it clicks into place.

note

Tighten the lamp cover securely so you do not receive a lamp cover error when you turn the projector back on.

8. Replace the lamp cover, then tighten its screw.

9. Reset the lamp timer as described in the next section.

130


Resetting the Lamp Timer

After you replace the lamp, you need to reset the lamp timer using the projector’s menu system.

1. Press the

Menu

button on the remote control or on the projector’s control panel. You see the main menu.

2. Select the

Reset

menu and press

Enter


3. Select

Reset Lamp Hours

and press

Enter

.

4. When you see the prompt, select

Yes and press

Enter

.


Menu

to exit.

Checking Lamp Usage

To check the number of hours the lamp has been used, press the

Menu

button and highlight the

Info

menu. You see a screen like this:

note

The information displayed depends on the input signal currently selected.

If you have used the projector for less than

10 hours, the hours are listed as

0H

.


131

caution

When replacing batteries, take the following precautions:

■

Replace the batteries as soon as they run out. If the batteries leak, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash immediately.

■

Do not expose batteries to heat or flame.

■

Dispose of used batteries according to local regulations.

■

Do not use batteries other than those specified in this

User’s Guide and do not

use batteries of different types or mix old and new batteries.

■

Keep these batteries out of the reach of children.

Batteries are choking hazards and are very dangerous if swallowed.

The life span of the lamp is about 2500 hours if

Power

Consumption

in the Settings menu is

Normal

(default), and 3500 hours if this setting is

ECO

. Make sure you have a spare lamp handy if the usage hours on this menu are close to the life span of your lamp.

Replacing the Pen Batteries

To check the pen batteries, press the button. If the indicator light is green, the battery has enough power.

Battery indicator light

Button

If you need to replace the batteries, use two rechargeable or alkaline

AAA batteries.

1. Press in the tab on the battery cover as you lift the cover off.

2. Install two batteries, inserting the

+ and

–

ends as shown.

132


3. Replace the battery cover and press it down until it clicks into place.

Replacing the Remote Control Batteries

Replace the batteries in the remote as described below:

1. Turn the remote control over.

2. Press in on the catch on the battery cover as you lift the cover off.

3. Install two AA alkaline batteries, inserting the

+ and

–

ends as shown.


133

4. Replace the battery cover and press it down until it clicks into place.

note

Epson shall not be liable for any damages incurred during transportation.

Transporting the Projector

The projector contains many glass and precision parts.

Follow these guidelines to prevent damage when transporting it:

■ When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector.

■ When transporting the projector a long distance, first place it in a hard-shell shipping case, then pack it in a firm box with cushioning around the case.

134


■

■

■

■

■

■

■

■

■

Solving Problems

T his chapter helps you solve problems with your projector and tells you how to contact technical support for problems you can’t solve yourself. The following information is included:

Using the projector’s on-screen help system

What to do when the projector’s status lights flash

Solving projector operation problems

Solving problems with the image or sound

Solving problems with the interactive pen

Solving password problems

Solving network problems

Solving problems with the remote control

Contacting technical support

8

135

136

Solving Problems

Using On-Screen Help

If the image doesn’t look right or your audio isn’t working, you can get help by pressing the

?

Help

button on the projector or the remote control.

1. Press the

?

Help

button on the remote control or on the projector. You see the Help menu:

2. Use the arrow buttons on the remote control or the projector to highlight menu items.

3. Press the

Enter

button on the remote control or the projector to select the menu item and read the solutions.

4. To exit the help system, press the

? Help

button or

Esc

button.

If none of the suggestions solve your problem, see additional solutions to problems in the following sections.

Checking Projector Status

If your projector isn’t working correctly, first turn it off and unplug it.

Then plug the power cord back in and turn on the projector. If this doesn’t solve the problem, check the lights on top of the projector.

What To Do When the Lights Flash

The lights on top of the projector indicate the projector’s status.

Power light

Lamp light

Temperature light

Refer to the following tables for a complete description of the projector’s status lights:

Power light status

P

Power light status Description

Flashing green The projector is warming up. Wait for the image to appear.

Green

Orange

Flashing orange

Red or flashing red

The projector is operating normally.

The projector is in sleep or standby mode. You can unplug it or press the

P power button to turn it on.

Preparing for network monitoring or cooling down.

There is a problem with the projector. Check the next table to diagnose the problem.

Solving Problems

137

Error light(s) status

Error light(s) status Description

P

Green or orange

Flashing orange

It’s time to replace the lamp. See page 127 for instructions. If you continue to

use the lamp after the replacement warning, there is an increased possibility that the lamp may break.

Off

P

Flashing red

P

Off

Flashing orange

Red

Off

Rapid cooling is in progress. Although this is not an abnormal condition, projection will stop automatically if the temperature rises higher. Make sure there is plenty of space around and under the projector for ventilation, and that the air filter and vents are clean.

The projector is overheating, which turns the lamp off automatically. Wait until the projector switches to standby mode (about 5 minutes). Make sure there is plenty of space around and under the projector for ventilation.

Red

The air filter may be clogged. Clean or replace the air filter as described on

pages 125 to 127.

If you’re using the projector above an altitude of 4,900 feet (1,500 meters), turn

on High Altitude Mode in the Operation menu (see page 92).

If the projector continues to overheat after you clean the air filter, stop using the projector, disconnect the power cord, and contact Epson for help as

described on page 155.

P

Flashing red

Red

Flashing red

P

Red

Warning: Except as specifically explained in this User’s Guide, do not attempt to service this product yourself.

The projector has an internal problem. Stop using the projector, disconnect the

power cord, and contact Epson for help, as described on page 155.

There is a problem with the fan or temperature sensor. Stop using the projector, disconnect the power cord, and contact Epson as described on

page 155.

Off

Flashing red

P

Red

Flashing red

Off

The lamp may be burnt out. First make sure the lamp cover is securely installed. If that’s not the problem, the air filter may be clogged. Clean or

replace the air filter as described on pages 125 to 127.

If this does not resolve the problem, let the lamp cool and then remove it. If the

lamp is cracked, replace it as described on page 127. If the lamp is not cracked,

reinstall it. If reinstalling doesn’t work, replace the lamp.

P

Flashing red

Flashing red

Flashing red

If you’re using the projector above an altitude of 4,921 feet (1,500 meters), turn

on High Altitude Mode in the Operation menu (see page 92).

If none of these suggestions resolves the problem, contact Epson as described

on page 155.

The projector has an Auto Iris error or power error. Stop using the projector, disconnect the power cord, and contact Epson for help, as described on

page 155.

138

Solving Problems

Solving Projector Operation Problems

The power doesn’t turn on.

■ If the projector doesn’t turn on when you press the Ppower button, make sure the power cord is connected to the projector and plugged into a working electrical outlet.

■

■

The power cord may be defective. Disconnect the cord from the

outlet and contact Epson as described on page 155.

If you’re using the Direct Power On function and you immediately plug the power cord back in after unplugging it, the power may not turn back on. Press the Ppower button to turn the projector back on.

The buttons on the projector don’t work.

If the Control Panel Lock function has been enabled, you can’t use the buttons on the projector. Try using the remote control instead, or press and hold the projector’s

Enter

button for seven seconds to

release the lock (see page 97).

You are having trouble projecting through the USB cable connection.

■ Press the

USB


■ If the USB Display driver is not installed automatically the first time you connect the cable, do one of the following:

Windows: Double-click

Computer

or

My Computer

>

EPSON_PJ_UD

>

EMP_USDE.EXE

.

Mac OS: Double-click

EPSON_PJ_UD

>

USB Display

Installer

.

Solving Problems

139

140

Solving Problems

■

■

■

■

■

■

If nothing is projected after the drivers are installed, do one of the following:

Windows: Select or

Start

>

All Programs

or

Programs

>

EPSON Projector

>

EPSON USB Display

>

EPSON USB

Display Vx.x

.

Mac OS: Click the

USB Display

icon in the Dock. If you don’t see it, open the

USB Display folder in the Applications folder and run

USB Display

.

Make sure

USB Type B

in the Extended menu is set to

USB

Display

(see page 92).

In Windows, if the mouse pointer flickers, select

All Programs or

Programs

>

EPSON Projector

>

EPSON USB Display

>

EPSON USB Display Vx.x

., then clear the

Transfer layered window

checkbox.

With Windows DirectX, turn off DirectX functions.

If you are using Windows Media Center, make sure you use window display mode, rather than full-screen display mode.

If the image is choppy, make sure you are using a USB 2.0 interface on your computer.

Solving Problems With the Image or Sound

No image appears on the screen.

■ Check that the Ppower light is green and not flashing. Also press the

A/V Mute button on the remote control to make sure the picture has not been turned off temporarily.

■ The projector may be in standby or sleep mode. If the Ppower light is orange, press the Ppower button to turn the projector on.

■

■

■

■

■

■

■

■

If the power was switched off and then on again, the projector may be cooling down. Wait until the Ppower light stops flashing and remains orange; then press the Ppower button again.

The attached computer may be in sleep mode or displaying a black screen saver. Try pressing a key on the computer.

If you are projecting from a DVD player or other video source, make sure you turn it on and press its

Play

button.

If you are projecting video from a laptop, you may need to set the laptop to external output only.

If you are projecting from a composite or S-Video video source,

make sure the Video Signal setting is correct (see page 87).

You can also try resetting all of the menu settings (see page 85).

If you’re projecting through your computer’s USB port, make sure the

USB Type B

setting in the Extended menu is set to

USB

Display

(see page 92).

With Windows, you may need to install the USB display drivers manually by clicking

My Computer

or

Computer

>

EPSON_PJ_UD

>

EMP_UDSE.EXE

. If nothing is projected after the USB display drivers are installed, click

All Programs

or

Programs

>

EPSON Projector

>

EPSON USB Display

>

EPSON USB Display Vx.x

on your computer.

With Mac OS X, click the

USB Display

icon in the Dock. If there is no USB Display icon in the Dock, open the

USB Display folder in the Applications folder and run

USB Display

.

If you see a black screen and you are connected through your computer’s USB port (or through your network), the application may be using DirectX drawing features, which are not supported.

Solving Problems

141

142

Solving Problems

You’ve connected a computer and see a blue screen with the message

No Signal

displayed.

■

Make sure the cables are connected correctly, as described

beginning on page 22.

■

■

If you’ve connected a computer and one or more video sources, you may need to press the

Source Search button to select the correct source. Allow a few seconds for the projector to sync up after pressing the button.

■

Make sure the power for your connected equipment is turned on.

If you’re using a PC notebook:

Press the function key that lets you display on an external monitor. It may have an icon such as , or it may be labelled

CRT/LCD

. You may have to hold down the

Fn

key while pressing it. Allow a few seconds for the projector to sync up after changing the setting. Check your notebook’s manual or online help for details.

■

On most systems, the key lets you toggle between the LCD screen and the projector, or display on both at the same time.

Depending on your computer’s video card, you might need to use the Display utility in the Control Panel to make sure that both the

LCD screen and external monitor port are enabled. See your computer’s documentation or online help for details.

If you’re using Mac OS X:

1. Open

System Preferences

.

2. Click

Display

or

Displays

.

3. Click

Detect Displays

.


Mac OS X 10.6: Click

Show displays in menu bar

.

Other versions of Mac OS X: Make sure the

VGA Display

or

Color LCD

dialog box is selected. Click the

Arrangement

or

Arrange

tab and make sure the

Mirror Displays

checkbox is selected.

The message

Not Supported

is displayed.

■

Make sure the correct input signal is selected in the Signal menu

(see page 87).

■

Make sure your computer’s resolution and frequency or refresh

rate is supported by the projector (see page 160). If necessary,

change your computer’s settings.

The projector and notebook don’t display the same image

If you’re projecting from a notebook, and you can’t see your image on the projection screen and on your computer at the same time, follow these guidelines.

If you’re using a PC notebook:

■ On most systems, there’s a function key that lets you toggle between the LCD screen and the projector, or display on both at the same time. It may be labeled

CRT/LCD

or have an icon such as

. You may have to hold down the

Fn

key while pressing it.

Allow a few seconds for the projector to sync up after changing the setting.

■ If the function key doesn’t permit you to display simultaneously on both screens, you should check your monitor settings to make sure both the LCD screen and the external monitor port are enabled.

From the Control Panel, open the

Display

utility, select the

Settings

option, then select the

Advanced

option (in Windows

Vista, right-click on the desktop, select

Personalize

, select

Display Settings

, then select

Advanced Settings

). The method for adjusting the settings varies by brand; you may need to click a

Monitor

tab, then make sure the external Monitor port is set as your primary display and/or enabled. See your computer’s documentation or online help for details.

Solving Problems

143

144

Solving Problems

If you’re using Mac OS X:

You may need to set up your system to display on the projector screen as well as the LCD screen. Make sure your projector is connected and follow these steps:

1. Open

System Preferences

.

2. Click

Display

or

Displays

.

3. Click

Detect Displays

.


Mac OS X 10.6.x: Click

Show displays in menu bar

.

Other versions of Mac OS X: Make sure the

VGA Display

or

Color LCD

dialog box is selected, click the

Arrangement

or

Arrange

tab, then make sure the

Mirror Displays

checkbox is selected.

Only part of the computer image is displayed.

■ Press the

Auto

button on the remote control or the

Enter

button on the projector.

■

■

■

■

■

Make sure the image

Position

setting is correct in the Signal

menu. See page 88 for more information.

Press the

Aspect button on the remote control or select the correct

Aspect

setting from the Signal menu. See page 44 for

details on the available options.

Press the

Esc

button on the remote control to cancel the E-Zoom function.

Make sure your computer’s resolution setting is correct. See the

compatible video formats listed on page 160.

You also may need to modify existing presentation files if you created them for a different resolution. See your software documentation for specific information.

■

■

If you’re projecting a widescreen computer image, adjust the

Resolution

setting (see page 87), if necessary.

If you’re projecting an image from a computer with dual display activated, turn dual display off.

The image isn’t square, but keystone-shaped.

If the image isn’t evenly rectangular, adjust its shape using the

Keystone setting on the Settings menu (see page 89).

The image contains static or noise.

■

If you’re using a computer cable longer than 6 feet (1.8 meters), or an extension cable, the image quality may be reduced.

■

■

■

■

■

■

■

■

Keep your computer and video cables away from the power cord as much as possible to prevent interference.

The video signal may be split between the computer and the projector. If you notice a decline in the projected image quality when the image is displayed simultaneously on your notebook computer and the projector, turn off the notebook’s LCD display.


(see page 88).

If you’re using a composite, S-Video, or component video source with 480i signals, turn on the

Progressive

setting on the Signal

menu (see page 88).

If you’ve used the Keystone adjustment, you may need to decrease the

Sharpness

setting in the Image menu (see page 86).

If you’re projecting from a computer, make sure its signal is

compatible with the projector. See page 160.

If you’re projecting from a computer, press the

Auto

button on the remote control to reset the projector’s Tracking, Sync, and

Position settings.

Reconnect the interface cable or try a different cable.

Solving Problems

145

note

You must be projecting an image for the

Auto

button to have any effect. It works only with computer images projected through the

Computer (Component

Video)

port.

■

■

The image is blurry.

■

There may be dirt or smears on the projection window. Clean the

window as described on page 124.

■

Adjust the focus using the focus lever (see page 42).

Lower the projection angle to reduce the amount of keystone correction required.

If you’re projecting from a computer, you may need to adjust the tracking and sync settings as described in the next section.

You see vertical bands or the image still looks blurry after trying the solutions in the previous section.

■ If you’re projecting from a computer and displaying an image that contains a lot of fine detail, you may notice vertical bands or some of the characters may look heavy or blurred. Press the

Auto button on the remote control or the

Enter

button on the projector to reset the projector’s Tracking, Sync, and Position settings.

■ If further adjustment is needed, you can fine-tune the

Tracking and

Sync

settings manually using the Signal menu, as described

on page 88.

1. Fill the screen with an image containing fine detail, such as a pattern to appear as your desktop background, or try projecting black text on a white background.

2. Adjust the

Tracking

to eliminate vertical bands.

146

Solving Problems

3. Adjust the

Sync

setting to increase the image sharpness.

■

■

■

The image is too light or dark, or colors are incorrect.

■

Press the

Color Mode

button or select a different

Color Mode

option in the Image menu. See page 43 for details on the available

options.

■

If you’re displaying video, adjust the

Color Adjustment

and

Color Mode settings on the Image menu. You can also try adjusting the

Color Saturation

,

Abs. Color Temp

, and

Tint settings on the Image menu.

■

■

■

Try adjusting the

Brightness

and

Contrast settings on the Image menu.

Try adjusting the

Power Consumption

setting (see page 89).

Check your computer display settings to correct the color balance.

The projector’s lamp may need to be replaced. See page 127 for

instructions.


(see page 88).

Make sure that all cables are connected to the proper ports and connected securely.

note

Because of the different technologies used, your projected image may not exactly match the colors on your notebook or computer monitor.

Nothing appears on an external monitor.

The only images that can be displayed on an external monitor are computer images connected through the

Computer1 port (see

page 22).

Solving Problems

147

148

Solving Problems

■

■

There is no sound, or the sound is not loud enough.

■

Use the

Volume

buttons to adjust the volume (see page 76), or

adjust the

Volume

setting in the Settings menu.

■

■

■

Make sure you are using a “no resistance” audio cable.

Make sure A/V Mute is not enabled. (Press the

A/V Mute

button to disable it.)

If your presentation includes computer audio, make sure the volume control on your computer is not turned all the way down or muted. In Windows, you may be able to check this by clicking the volume control in your Windows system tray (lower right corner of the screen). On a Mac, you may be able to adjust the volume from your menu bar (top right corner of the screen) or via the volume control function keys.

If you’re using a DVD player or other video source, make sure the

cables are connected correctly, as described on page 31.

If you are using a microphone connected to the projector’s

Mic port, make sure the cable is connected securely and the

Mic Input

Volume

on the Settings menu is adjusted correctly. See page 89

for more information.

Solving Problems With the Interactive

Pen

You see the message “Hardware device not found” when you try to use the Easy Interactive Driver.

■ Make sure the USB cable is securely connected to the projector and computer. Try disconnecting and reconnecting the cable to your computer.

■ If you’re using a laptop computer, make sure the battery has enough power.

■

■

If an antivirus program is running, try disabling it and restarting the Easy Interactive Driver.

If your USB cable is installed in the wall, try connecting a different USB cable to the projector and your computer.

You don’t see the Easy Interactive Driver on your computer.

If you don’t see the pen icon on your taskbar (Windows) or in the Dock (Mac OS), do one of the following:

■

■

■

■

Make sure you install the driver from the CD labeled “Epson

Projector Software for Easy Interactive Function.”

In Windows, select

All Programs

or

Programs

>

Epson

Projector

>

Easy Interactive Driver

.

In Mac OS, open the Application folder, then select the

Easy

Interactive Driver

icon.

If the pen icon has a red

X

on it, make sure the USB cable is securely connected to the projector and computer. Try disconnecting and reconnecting the cable to your computer.

The pen doesn’t work.

■

Make sure nothing is blocking the signal between the pen and the

interactive pen receiver on the projector (see page 13).

■

■

■

■

Make sure the cable cover is in place to keep cables from blocking the signal.

Make sure the pen batteries have enough power. If the light on the pen doesn’t turn green when you press the button, you need to replace the batteries.

Dim the room lights and turn off any fluorescent lights. Make sure the projection surface and the pen receiver are not in direct sunlight or other sources of bright lighting.

Make sure the pen receiver on the projector is clean and free from dust.

Solving Problems

149

150

Solving Problems

■

■

■

■

Make sure the USB cable is securely connected to the projector and computer. Try disconnecting and reconnecting the cable to your computer.

Make sure there is no interference from infrared remote controls or infrared microphones.

Make sure the location is free from electromagnetic interference from nearby equipment (such as electric motors or transformers).

If the tablet function does not work, you may have other tablet device drivers on your system. Uninstall the Easy Interactive

Virtual Tablet Driver using the Windows Control Panel.

The pen is hard to use.

For easier operation, hold the pen at an angle to the projection surface.

■

■

The pen position is not accurate.

■

If you use the

E-Zoom +

button on the remote control to enlarge the image, the pen position will not be accurate. When you return to the original size, the pen position should be correct.

You may need to recalibrate (see page 47).

Make sure the cable cover is in place to keep cables from blocking the signal.

You’re having trouble calibrating.

■ If the flashing circles don’t appear, make sure the VGA cable and

USB cable are securely connected to the computer. Try restarting

the Easy Interactive Driver, as described on page 149.

■ If the circles don’t stop flashing and turn black (or they stop flashing and turn black automatically), dim or turn off any bright lights near the projection surface.

■

■

Solving Password Problems

If you cannot enter or remember a password, try the following solutions:

You may have turned on password protection without first setting a password. Try entering

0000

using the remote control.

If you have entered an incorrect password too many times and see a message displaying a request code, write down the code and

contact Epson as described on page 155.

Solving Network Problems

You can’t display an image using Quick Wireless

Connection.

You may need to restart your computer to connect.

■

■

You can’t connect to the projector using EasyMP Network

Projection.

■ Make sure the network cable is connected, as described on

page 100.

■

■

If you are using the optional wireless LAN module, make sure it is

installed correctly in the projector, as shown on page 103.

Restart your computer.

Make sure your projector and computer are configured correctly;

see page 108 (configuring the projector) or page 110 (configuring

the computer).

If you are using the optional wireless LAN module, make sure that you have sufficient wireless signal strength (above 50 percent). On a Mac, check the AirPort icon on the Mac menu bar. In Windows, see the documentation for your computer’s wireless card or adapter for details.

Solving Problems

151

152

Solving Problems

■

■

■

■

■

■

■

Make sure you aren’t projecting one of the EasyMP Network

Projection screens. (You should see a message that the projector is ready to connect.) If you have to exit a configuration screen, restart EasyMP Network Projection.

If the projector is configured for Access Point mode and you’re using DHCP, allow time for your projector to appear. It takes the server a little while to pick up the IP address.

If you’ve changed any settings for your projector or network, or restarted your computer, allow a minute or two for the connection to appear. If you’re using AirPort, try turning AirPort off and then on again.

Make sure that you’re trying to connect to the right network. In

Windows, verify that you’ve enabled your computer’s connection to the access point or that your wireless card or adapter is enabled and connected to the same SSID as the projector. On a Mac, click the AirPort icon at the top of your Mac desktop to make sure

AirPort is turned on and the right network is selected.

If you have an access point or AirPort base station and you’re not using DHCP, check your projector’s IP address on the Access

Point mode advanced settings screen. The first three segments of the IP address should be identical to the first three segments of the

IP address of your access point or base station. The last segment of the projector’s IP address should be close, but not identical, to the last segment of the IP address of the access point or base station.

If you’re not using DHCP, check your projector’s Gateway address on the projector’s Access Point mode advanced settings screen. It should be identical to the IP address for your access point or AirPort base station.

If you’re using a projector keyword, it changes each time you turn the projector off and then on again. Check the projector’s keyword on the LAN standby screen and enter it at the prompt.

■

■

■

■

■

If you’re using AirPort, check the configuration of your network.

Start the AirPort Admin utility, select your base station, click

Configure and click

Show All Settings

. Click the

Network tab. If you set up your projector to connect in DHCP mode, turn on

Distribute IP Addresses

and

Share a Single IP Address

.

If you’re using AirPort and DHCP is turned off on your projector’s Access Point mode advanced settings screen, make sure

Distribute IP Addresses

is off.

If you’re using Access Point mode and you’re connecting to the wrong network, you may be experiencing signal interference from another network. Try resetting your access point or base station, then restart EasyMP Network Projection.

If you’re using AirPort, the projector’s SSID should match the

AirPort network name, not the name of the AirPort base station.

To check the network name, start the AirPort Admin utility, select your base station, and click

Configure

. Then click

Show

All Settings

. The network name appears on the AirPort tab.

If you’re prompted for a password when you connect, enter the

WEP encryption key (if you’re using WEP encryption).

You are not receiving mail when a projector problem occurs.

■ Make sure the Mail settings are correct in the Network menu. For

details, see page 115.

■ To receive mail notification when the projector is in standby mode, you need to set

Standby Mode

to

Communication On

in the Extended menu. See page 92.

Solving Problems

153

154

Solving Problems

Solving Problems With the Remote

Control

The projector doesn’t respond to remote control commands.

■ Point the remote control towards the projector’s receiver. Make sure you are within 19.7 feet (6 meters) of the projector and within a 30° horizontal angle and a 15° vertical angle from the projector’s front or back receiver.

■

■

■

■

■

The remote control’s batteries may not be installed correctly or

may be low on power. To change the batteries, see page 133.

Dim the room lights and turn off any fluorescent lights. Make sure the projector is not in direct sunlight. Strong lighting, especially fluorescent lights, may affect the projector’s infrared receivers. Also, turn off any nearby equipment that emits infrared energy, such as a radiant room heater.

If you can’t adjust the room lighting, you can turn off one of the remote receivers by using the Settings menu. Make sure the

receivers are not both turned off (see page 90).

Check to see if a button on the remote control is stuck down, causing it to enter sleep mode. Release the button to wake the remote.

If you want to use the remote control as a wireless mouse (or to move through presentation slides), make sure

USB Type B

in the

Extended menu is set to Wireless Mouse (see page 92). Also,

make sure you have connected the USB cable.

Where To Get Help

Epson provides these technical support services:

Internet Support

Visit Epson’s support website at www.latin.epson.com for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail

Epson with your questions. (Site available only in Spanish and

Portuguese.)

Speak to a Support Representative

You may speak with a projector support specialist by dialing one of these numbers:

Country

Argentina

Brazil

Chile

Colombia

Costa Rica

Telephone

(54 11) 5167-0300

(55 11) 3956-6868

(56 2) 230-9500

(57 1) 523-5000

(50 6) 2210-9555

800-377-6627

Mexico

Mexico City

Other Cities

Peru

Venezuela

(52 55) 1323-2052

01 800-087-1080

(51 1) 418-0210

(58 212) 240-1111

If your country does not appear on the list, contact the nearest Epson sales office. Toll or long distance charges may apply.

Solving Problems

155

156

Solving Problems

■

■

■

■

■

Before you call for support, please have the following information ready:

Product name (BrightLink 455Wi+)

Product serial number (located on the bottom of the projector and on the Info menu)

Proof of purchase (such as a store receipt) and date of purchase

Computer or video configuration

Description of the problem

Purchase Supplies and Accessories

You can purchase screens and other accessories from an Epson authorized reseller. To find the nearest reseller, call Epson as described above.


General

Type of display

Resolution

(native format)

Color reproduction

Light output

(brightness)

Poly-silicon TFT active matrix

1280 × 800 pixels (WXGA)

16.8 million colors

Contrast ratio

Image size

Projection distance

Normal mode:

White light output 2500 lumens

(ISO 21118 standard)

Color light output 2500 lumens

ECO mode:

White light output 1740 lumens

(ISO 21118 standard)

Color light output 1740 lumens

2000:1 (Dynamic color mode, Normal

Power Consumption, with

Auto Iris setting turned on in the Image menu;

see page 85)

59 to 97 inches (149.8 to 246.4 cm)

18.3 to 30.1 inches (0.465 to 0.766 m), lens to projection surface front or rear ceiling mount Projection methods

Internal sound system

(monaural)

Optical aspect ratio

Zoom ratio

12 W

16:10 (horizontal:vertical)

Digital 1:1.35

A

157

Noise level

Keystone correction

note

Lamp life will vary depending upon mode selected, environmental conditions, and usage.

Brightness decreases over time.


Projection Lamp

Type

Power consumption

Lamp life

Part number

Remote Control

Range

Batteries (2)

Dimensions

Height

Width

Depth

Weight

28 dB in ECO mode

35 dB in Normal mode

±

5°

UHE (Ultra High Efficiency

E-TORL

®

)

230 W

Approx. 2500 hours (Normal mode)

Approx. 3500 hours (ECO mode)

V13H010L57

19.7 feet (6 meters)

Alkaline AA

6.1 inches (155 mm)

19 inches (483 mm)

14.5 inches (369 mm)

Approximately 12.9 lb (5.8 kg) without slide plate

Approximately 14.1 lb (6.3 kg) with slide plate

158


Electrical

Rated frequency

Power supply

Power consumption

100 to 120 V

220 to 240 V

50/60 Hz AC

100 to 240 VAC

±

10%, 3.4 A to 1.4 A

268 W in ECO mode

363 W Normal mode

0.3 W Standby (Communication Off)

10 W Standby (Communication On)

257 W in ECO mode

343 W Normal mode

0.3 W Standby (Communication Off)

12 W Standby (Communication On)

Environmental

Temperature

Humidity

(non-condensing)

Operating altitude

Operating: 41 to 95 °F (5 to 35 °C)

Storage: 14 to 140 °F (–10 to 60 °C)

Operating: 20 to 80% RH

0 to 7500 ft (0 to 2286 m); over 4921 ft (1500 m), enable

High

Altitude

mode in the Extended menu

(see page 91)

Safety and Approvals

United States

Canada

FCC 47CFR Part 15B Class B (DoC)

UL60950-1 Second Edition (cTUVus

Mark)

ICES-003 Class B

CSA C22.2 No. 60950-1-07

Pixelworks

™

DNX

™

ICs are used in this projector.


159

160


Compatible Video Formats

This projector supports the high definition video and computer display formats listed here.

To project images output from a computer, the computer’s video card must be set at a refresh rate (vertical frequency) that’s compatible with the projector. Some images are automatically resized using Epson’s

SizeWize

™

technology to display in the projector’s native format. The frequencies of some computers may not allow images to display correctly; see your computer’s documentation for details.

SXGA1—70

SXGA1—75

SXGA1—85

WXGA—60

WXGA—75

WXGA—85

SXGA2—60

SXGA2—75

SXGA2—85

SXGA3—60

SXGA3—75

SXGA3—85

WXGA1—60

WXGA2—60

Mode

Refresh rate (Hz)

Computer signals (analog RGB)

VGA—60

VESA—72

VESA—75

VESA—85

SVGA—56

SVGA—60

SVGA—72

SVGA—75

SVGA—85

XGA—60

XGA—70

XGA—75

XGA—85

60

72

75

85

56

60

72

75

85

60

70

75

85

60

75

85

60

75

85

60

60

70

75

85

60

75

85

Resolution

640 × 480

640 × 480

640 × 480

640 × 480

800 × 600

800 × 600

800 × 600

800 × 600

800 × 600

1024 × 768

1024 × 768

1024 × 768

1024 × 768

1152 × 864

1152 × 864

1152 × 864

1280 × 800

1280 × 800

1280 × 800

1280 × 960

1280 × 960

1280 × 960

1280 × 1024

1280 × 1024

1280 × 1024

1280 × 768

1360 × 768

Mode

WXGA+—60

WXGA+—75

WXGA+—85

SXGA+60

SXGA+75

UXGA—60

WSXGA+—60*

MAC13

MAC16

MAC19

MAC19-60

MAC21

Composite video, S-Video

NTSC

PAL

PAL—60

SECAM

SECAM—60

60

50

60

50

60

60

67

75

75

60

75

60

75

60

Refresh rate (Hz)

60

75

85

Resolution

1440 × 900

1440 × 900

1440 × 900

1400 × 1050

1400 × 1050

1600 × 1200

1680

×

1050

640 × 480

832 × 624

1024 × 768

1024 × 768

1152 × 870

720 × 480

720 × 576

720 × 576

720 × 576

720 × 576

Component video

SDTV (480i)

SDTV (576i)

SDTV (480p)

SDTV (576p)

HDTV (720p)

HDTV (1080i)

60

50

60

50

60/50

60/50

720 × 480

720 × 576

720 × 480

720 × 576

1280 × 720

1920 × 1080

* Available only when you select Wide as the Resolution setting


161

162


Notices

T his appendix includes safety instructions and other important information about your projector.

Important Safety Instructions

■

■

■

■

Follow these safety instructions when setting up and using the projector:

■

■

■

■

■

■

Do not look into the lens when the projector is on. The bright light can damage your eyes.

Do not operate the projector on its side, or while tilted to one side.

Do not tilt the projector forward or back at a greater angle than that

specified for keystone correction (see page 158).

The projector should be installed by qualified technicians using mounting hardware designed for use with this projector.

If you apply adhesives to the mount to prevent the screws from loosening, or if you use lubricants or oils on the projector, the projector case may crack and the projector may fall from its mount. This could cause serious injury to anyone under the mount and could damage the projector. When installing or adjusting the mount, do not use adhesives to prevent the screws from loosening and do not use oils or lubricants.

Do not use the projector where it may be exposed to rain, water, or excessive humidity. Do not handle the pen with wet hands.

Unplug the projector from the wall outlet before cleaning. Use a dry cloth (or, for stubborn dirt or stains, a moist cloth that has been wrung dry) for cleaning. Do not use liquid or aerosol cleaners.

Never spill liquid of any kind into the projector.

Do not use the projector where it may be exposed to excessive dust or smoke.

Never push objects of any kind through the cabinet slots.

Do not use or store the projector or remote control in a hot location, such as near a heater, in direct sunlight, or in a closed vehicle.

163

B

164

Notices

■

■

■

■

■

■

■

■

■

■

■

■

■

Do not block the slots and openings in the projector case. They provide ventilation and prevent the projector from overheating. Do not operate the projector on a sofa, rug, or other soft surface, or set it on top of loose papers, which could block vents underneath your projector. If you are setting up the projector near a wall, leave at least 7.9 inches (20 cm) of space between the wall and the air exhaust vent.

Do not operate the projector in a closed-in cabinet unless proper ventilation is provided.

If you are using two or more projectors side-by-side, leave at least 2 feet

(60 cm) of space between the projectors to allow for proper ventilation.

You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector.

Do not store the projector outdoors for an extended length of time.

Do not use the projector outside the required temperature range of

41 to 95 °F (5 to 35 °C). Doing so may cause an unstable display and could lead to projector damage.

Do not store the projector outside the required temperature range of

14 to 140 °F (–10 to 60 °C) or in direct sunlight for long periods of time. Doing so may cause damage to the case.

Do not touch the plug during an electrical storm. Otherwise, you may receive an electric shock.

Unplug the projector when it will not be used for extended periods.

Unplug the projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: if it does not operate normally when you follow the operating instructions, or exhibits a distinct change in performance; if smoke, strange odors, or strange noises come from the projector; if the power cord or plug is damaged or frayed; if liquid or foreign objects get inside the projector, or if it has been exposed to rain or water; if it has been dropped or the housing has been damaged.

Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified personnel.

Opening or removing covers may expose you to dangerous voltages and other hazards.

Never open any covers on the projector except as specifically explained in this User’s Guide. Never attempt to disassemble or modify the projector. Refer all repairs to qualified service personnel.

Use the type of power source indicated on the projector. Use of a different power source may result in fire or electric shock. If you are not sure of the power available, consult your dealer or power company.

■

■

■

■

■

■

■

■

■

■

■

■

If you use the projector in a country other than where you purchased it, use the correct power cord for that country.

Do not overload wall outlets, extension cords, or power strips. Do not insert the plug into a dusty outlet. This can cause fire or electric shock.

Take the following precautions when handling the plug: Do not hold the plug with wet hands. Do not insert the plug into an outlet with dust present. Insert the plug firmly into the outlet. Do not pull the power cord when disconnecting the plug; always be sure to hold the plug when disconnecting it. Failure to comply with these precautions could result in fire or electric shock.

Do not place the projector where the cord can be walked on.

The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.

Do not place anything that can become warped or damaged by heat near the exhaust vents. Do not bring your hands or face close to the vents while projection is in progress.

Before you move the projector, make sure its power is turned off, the plug is disconnected from the outlet, and all cables are disconnected.

Never try to remove the lamp immediately after use because it will be extremely hot. Before removing the lamp, turn off the power and wait at least an hour to allow the lamp to cool completely.

Do not place the source of an open flame, such as a lit candle, on or near the projector.

Do not modify the power cord. Do not place heavy objects on top of the power cord or bend, twist, or pull it excessively. Keep the power cord away from hot electrical appliances.

If the lamp breaks, ventilate the room to prevent gases contained in the lamp from being inhaled or coming in contact with the eyes or mouth.

If the projector is mounted overhead and the lamp breaks, be careful to prevent pieces of glass from falling into your eyes when you open the lamp cover.

WARNING: The cords included with this product contain chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. (This notice is provided in accordance with Proposition 65 in Cal. Health & Safety Code

§25249.5 and following.)

Notices

165

166

Notices

FCC Compliance Statement

For United States Users

■

■

■

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

■

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

WARNING

The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces.

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

For Canadian Users

This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le materiel brouilleur du Canada.

Latin America Limited Warranty

1. Limited Warranty for Epson Products

Epson products are covered by warranty against defects in workmanship and materials when operated under normal use and handling conditions, as indicated in the product documentation, for the period specified in

section “Limited Warranty Coverage”. Coverage begins as of the date of delivery to the purchaser by Epson or

by an authorized Epson dealer (see “Epson Subsidiaries and Offices in Latin America”), in the country of

purchase.

Epson also guarantees that the consumables (ink cartridges, toner, batteries) included with the product, will perform according to the usage specifications as long as they are used prior to the expiration of their warranty period.

2. Scope of Warranty

Should Epson receive notice of a defect during the warranty period, it may, at its discretion, repair or replace the defective product at no cost to the purchaser. In the event of a replacement, the replaced equipment will become property of Epson. The replaced item may be new or previously repaired to the Epson standard of quality, and will assume the remaining warranty period of the product that was originally purchased.

This warranty does not include any compensation or damages whatsoever, resulting from the operating failures of the Epson product. In any event, Epson’s maximum liability toward the purchaser will be limited to the purchase price paid to Epson or to the authorized dealer.

Epson’s warranty does not cover any software not manufactured by Epson, even when delivered with an Epson product. The software may have a warranty provided by the manufacturer, as indicated in the documentation attached thereto.

3. Limitations and Exclusions

The warranty will be invalid in the following cases:

3.1 When the product’s serial number has been removed or altered.

3.2 When the product has been misused, has undergone unauthorized modifications, has been used or stored in ways that are not in compliance with the environmental specifications of the product.

3.3 When the damage resulted from the use of refilled supplies or consumables, or when damages are the result of use of media that does not meet the product’s specifications.

3.4 When damages resulted from the inappropriate transport of the equipment (packaging, installation, maintenance, transportation).

3.5 When damages were caused by natural or intentional disasters (fire, floods, lightning, earthquakes, etc.), power surges, or interaction with other brand products.

3.6 When the product has been totally or partially disassembled, or has been repaired other than by an Epson

Authorized Service Center.

Notices

167

3.7 When substances have been spilled on the product.

3.8 When the external plastic case has been scratched or abused.

3.9 When damages resulted from inappropriate tests, installation, maintenance or adjustments.

The warranty does not extend to accessories (lids, covers, trays) or replenishing supplies and consumables (ink cartridges, toner, ink ribbons, batteries, photosensitive units, knobs, print heads, lamps), which, due to their nature, must be regularly purchased through authorized dealers.

4. How to Obtain Warranty Service

Please refer to the user documentation to ensure that the product settings have been properly set and to perform the diagnostic tests indicated therein. Furthermore, in order for the unit to operate optimally, always use original Epson supplies and consumables.

To obtain warranty service, the purchaser may take the product to any Authorized Epson Service Center, along with proof of purchase, or call any of the Epson Technical Assistance Centers (see country list starting on

page 169).

Upon calling an Authorized Epson Service Center, the purchaser will be asked to provide the product model and serial numbers, and may be asked to provide information on the location and the date of purchase (the warranty is only valid in the country of purchase).

If there are no Authorized Service Centers in your area, call the Technical Assistance Center for service referral.

5. Responsibilities of Purchaser

The purchaser is responsible for the safety of all confidential and proprietary information stored on the product, as well as for recovery backup files in case of damage. Any activity related with the re-installation or resetting of the software that was delivered with the equipment, will be billed to the purchaser at the rates in effect at the Epson Service Center. This also applies if the failure was the result of a defect in the purchaser’s proprietary software or of a computer “virus”.

In order to obtain on-site service, the latter will be required to provide: access to the product; an appropriate working area; access to electrical facilities; access to the resources that may be necessary for the installation, repair or maintenance of the unit; a safety environment for Epson staff and their work tools.

168

Notices

6. Limited Warranty Coverage

Product

Projector

Model

BrightLink

Coverage

Two Years

Conditions

Service center

Technical Support Service

Epson offers technical assistance through electronic and telephone services. Before calling Epson, refer to the documentation included with your product. If you do not find the solution to your problem, visit Epson’s website at: www.latin.epson.com or call the local Epson office or an authorized dealer.

Service Centers

Country

Argentina

Brazil

Chile

Colombia

Costa Rica

Mexico

Peru

Venezuela

Telephone number

(54 11) 5167-0300

(55-11) 3956-6868

(56 2) 230-9500

(57 1) 523-5000

(50 6) 210-9555

800-377-6627

(52 55) 1323-2052

01-800-087-1080

(51 1) 418-0210

(58 212) 240-1111

Website

www.epson.com.ar

www.suporte-epson.com.br

www.epson.cl

www.epson.com.co

www.epsoncr.com

www.epson.com.mx

www.epson.com.pe

www.epson.com.ve

If your country does not appear on the preceding list, please contact the dealer where you purchased the product.

You may receive help or consult information online for all Epson products. Register your Epson equipment on our website, at www.latin.epson.com.

Extended Warranty Support and Service

In some countries, Epson offers warranty extension services. You may purchase this service by calling the

Technical Service Center.

Notices

169

Epson Subsidiaries and Offices in Latin America

Epson Argentina S.A.

Avenida Belgrano 964/970

(1092), Buenos Aires,

Argentina

Tel: (54-11) 5167-0300

Fax: (54 11) 5167-0333

Epson do Brasil Ltda.

Av Tucunaré, 720 - Tamboré

06460-020 Barueri - SP

(55-11) 3956-6868

(55-11) 3956-6806

Epson Chile, S.A.

La Concepción 322

Providencia, Santiago, Chile

Tel: (56-2) 484-3400

Fax: (56-2) 484-3413

Epson Colombia, Ltda.

Calle 100, No. 21-64 piso 7

Bogotá, Colombia

Tel: (57-1) 523-5000

Fax: (57-1) 523-4180

Epson Costa Rica, S.A

Embajada Americana,

200 Sur y 300 Oeste

San José, Costa Rica

Tel: (50-6) 210-9555

Fax: (50-6) 296-6046

Epson Mexico, S.A. de C.V.

Blvd. Manuel Ávila Camacho

389 Edificio 1 Conjunto

Legaria

Col. Irrigación, México, D.F.

C.P 11510 México

Tel: (52-55) 1323-2000

Fax: (52-55)1323-2183

Epson Peru, S.A.

Av. Canaval y Moreyra

590, San Isidro, Lima

27, Perú

Tel: (51-1) 418-0210

Fax: (51-1) 418-0220

Epson Venezuela, S.A.

Calle 4 con Calle 11-1

La Urbina Sur

Caracas, Venezuela

Tel: (58-212) 240-1111

Fax: (58-212) 240-1128

170

Notices

Software Notices

GNU GPL

This projector product includes the open source software programs which apply the

GNU General Public License Version 2 or later version ("GPL Programs").

We provide the source code of the GPL Programs until five (5) years after the discontinuation of same model of this projector product.

If you desire to receive the source code of the GPL Programs, please contact the customer support of your region.

These GPL Programs are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

The list of GPL Programs is as follows and the names of author are described in the source code of the GPL Programs

The list of GPL Programs

busybox-1.7.2

libgcc1(gcc-4.2.3) linux-2.6.20

patches udhcp 0.9.8

uvc rev.219

wireless_tools 29

Pixelworks PWC950 SDK drivers

The GNU General Public License Version 2 is as follows. You also can see the GNU

General Public License Version 2 at http://www.gnu.org/licenses/ .

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth

Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software

Foundation's software and to any other program whose authors commit to using it.

(Some other Free Software Foundation software is covered by the GNU Lesser

General Public License instead.) You can apply it to your programs, too.

Notices

171

When we speak of free software, we are referring to freedom, not price. Our General

Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.

Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all.

The precise terms and conditions for copying, distribution and modification follow.

GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING,

DISTRIBUTION AND MODIFICATION

0.

This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work containing the

Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you".

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.

172

Notices

1.

You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2.

You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.

b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this

License.

c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this

License.

3.

You may copy and distribute the Program (or a work based on it, under Section

2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:

Notices

173

a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.

4.

You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

5.

You are not required to accept this License, since you have not signed it.

However, nothing else grants you permission to modify or distribute the

Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the

Program or works based on it.

6.

Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.

174

Notices

7.

If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this

License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the

Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

8.

If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

9.

The Free Software Foundation may publish revised and/or new versions of the

General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.

Notices

175

10.

If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission.

For software which is copyrighted by the Free Software Foundation, write to the

Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

11.

BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO

WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY

APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE

COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM

"AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE

ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM

IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME

THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

12.

IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN

WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO

MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED

ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,

SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF

THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT

LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR

LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE

PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH

HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Programs

If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.

To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found.

<one line to give the program's name and a brief idea of what it does.>

Copyright (C) <year> <name of author>

176

Notices

This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software

Foundation; either version 2 of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY

WARRANTY; without even the implied warranty of MERCHANTABILITY or

FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin

Street, Fifth Floor, Boston, MA 02110-1301 USA.

Also add information on how to contact you by electronic and paper mail.

If the program is interactive, make it output a short notice like this when it starts in an interactive mode:

Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'. This is free software, and you are welcome to redistribute it under certain conditions; type

`show c' for details.

The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than `show w' and `show c'; they could even be mouse-clicks or menu items--whatever suits your program.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the program, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the program

`Gnomovision' (which makes passes at compilers) written by James Hacker.

<signature of Ty Coon>, 1 April 1989

Ty Coon, President of Vice

This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License.

GNU LGPL

This projector product includes the open source software programs which apply the

GNU Lesser General Public License Version 2 or later version ("LGPL Programs").

We provide the source code of the LGPL Programs until five (5) years after the discontinuation of same model of this projector product.

If you desire to receive the source code of the LGPL Programs, please contact the customer support of your region.

Notices

177

These LGPL Programs are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

The list of LGPL Programs is as follows and the names of author are described in the source code of the LGPL Programs.

LGPL Programs

uClibc-0.9.29

SDL-1.2.13

The GNU Lesser General Public License Version 2 is as follows. You also can see the

GNU Lesser General Public License Version 2 at http://www.gnu.org/licenses/ .

GNU LESSER GENERAL PUBLIC LICENSE

Version 2.1, February 1999

Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth

Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.

This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.

When we speak of free software, we are referring to freedom of use, not price. Our

General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.

To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.

178

Notices

For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.

We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library.

To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others.

Finally, software patents pose a constant threat to the existence of any free program.

We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license.

Most GNU software, including some libraries, is covered by the ordinary GNU General

Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public

License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.

When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public

License permits more lax criteria for linking other code with the library.

We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public

License for many libraries. However, the Lesser license provides advantages in certain special circumstances.

For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the

Lesser General Public License.

Notices

179

In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.

Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the

Library.

The precise terms and conditions for copying, distribution and modification follow.

Pay close attention to the difference between a "work based on the library" and a

"work that uses the library". The former contains code derived from the library, whereas the latter must be combined with the library in order to run.

GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR

COPYING, DISTRIBUTION AND MODIFICATION

0.

This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called "this License"). Each licensee is addressed as "you".

A "library" means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables.

The "Library", below, refers to any such software library or work which has been distributed under these terms. A "work based on the Library" means either the

Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term "modification".)

"Source code" for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the

Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the

Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does.

180

Notices

1.

You may copy and distribute verbatim copies of the Library's complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the

Library.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2.

You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library.

b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.

c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.

d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore,

Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library.

In addition, mere aggregation of another work not based on the Library with the

Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this

License.

Notices

181

3.

You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU

General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.

Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy.

This option is useful when you wish to copy part of the code of the Library into a program that is not a library.

4.

You may copy and distribute the Library (or a portion or derivative of it, under

Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of

Sections 1 and 2 above on a medium customarily used for software interchange.

If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.

5.

A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a

"work that uses the Library". Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.

However, linking a "work that uses the Library" with the Library creates an executable that is a derivative of the Library (because it contains portions of the

Library), rather than a "work that uses the library". The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.

When a "work that uses the Library" uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the

Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.

If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)

Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.

182

Notices

6.

As an exception to the Sections above, you may also combine or link a "work that uses the Library" with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications.

You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things: a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable "work that uses the Library", as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user's computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with.

c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.

d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place.

e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.

For an executable, the required form of the "work that uses the Library" must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

Notices

183

It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.

7.

You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things: a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above.

b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work.

8.

You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

9.

You are not required to accept this License, since you have not signed it.

However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.

10.

Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions.

You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License.

11.

If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this

License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the

Library.

184

Notices

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

12.

If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

13.

The Free Software Foundation may publish revised and/or new versions of the

Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation.

14.

If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software

Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

Notices

185

NO WARRANTY

15.

BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO

WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY

APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE

COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS

IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE

ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS

WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE

COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

16.

IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN

WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO

MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE,

BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,

INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR

INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF

DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY

YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH

ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.


How to Apply These Terms to Your New Libraries

If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License).

To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found.

<one line to give the library's name and a brief idea of what it does.>

Copyright (C) <year> <name of author>

This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free

Software Foundation; either version 2.1 of the License, or (at your option) any later version.

This library is distributed in the hope that it will be useful, but WITHOUT ANY

WARRANTY; without even the implied warranty of MERCHANTABILITY or

FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public

License for more details.

186

Notices

You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51

Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA

Also add information on how to contact you by electronic and paper mail.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the library, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for tweaking knobs) written by James Random Hacker.

<signature of Ty Coon>, 1 April 1990

Ty Coon, President of Vice

That's all there is to it!

BSD License (Berkeley Software Distribution License)

This projector product includes the open source software program "University of

California, Berkeley License (Berkeley Software Distribution License)" which applies the terms and conditions provided by owner of the copyright to the "BSD License".

The "BSD License" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

List of BSD License programs

busybox_1.7.2

License terms of conditions of each program which are provided by owner of the copyright to the “BSD License” are as follows.

Copyright (c) The Regents of the University of California. All rights reserved.

This code is derived from software contributed to Berkeley by Kenneth Almquist.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1.

Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2.

Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3.

Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

Notices

187

THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS''

AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED

TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS

OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT

LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF

USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND

ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR

TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF

THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH

DAMAGE.

libjpeg

This projector product includes the open source software program "libjpeg" which applies the terms and conditions provided by owner of the copyright to the "libjpeg".

The "libjpeg" are WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

List of libjpeg programs

libjpeg-6b

License terms of conditions of each program which are provided by owner of the copyright to the "libjpeg" are as follows.

Copyright (C) 1994-1997, Thomas G. Lane. This file is part of the Independent JPEG

Group's software. For conditions of distribution and use, see the accompanying

README file.

This distribution contains the sixth public release of the Independent JPEG Group's free JPEG software. You are welcome to redistribute this software and to use it for any purpose, subject to the conditions under LEGAL ISSUES, below.

LEGAL ISSUES

============

In plain English:

1.

We don't promise that this software works. (But if you find any bugs, please let us know!)

2.

You can use this software for whatever you want. You don't have to pay us.

3.

You may not pretend that you wrote this software. If you use it in a program, you must acknowledge somewhere in your documentation that you've used the

IJG code.

In legalese:

The authors make NO WARRANTY or representation, either express or implied, with respect to this software, its quality, accuracy, merchantability, or fitness for a particular purpose. This software is provided "AS IS", and you, its user, assume the entire risk as to its quality and accuracy.

188

Notices

This software is copyright (C) 1991-1998, Thomas G. Lane. All Rights Reserved except as specified below.

Permission is hereby granted to use, copy, modify, and distribute this software (or portions thereof) for any purpose, without fee, subject to these conditions:

(1) If any part of the source code for this software is distributed, then this README file must be included, with this copyright and no-warranty notice unaltered; and any additions, deletions, or changes to the original files must be clearly indicated in accompanying documentation.

(2) If only executable code is distributed, then the accompanying documentation must state that "this software is based in part on the work of the Independent

JPEG Group".

(3) Permission for use of this software is granted only if the user accepts full responsibility for any undesirable consequences; the authors accept NO

LIABILITY for damages of any kind.

These conditions apply to any software derived from or based on the IJG code, not just to the unmodified library. If you use our work, you ought to acknowledge us.

Permission is NOT granted for the use of any IJG author's name or company name in advertising or publicity relating to this software or products derived from it. This software may be referred to only as "the Independent JPEG Group's software".

We specifically permit and encourage the use of this software as the basis of commercial products, provided that all warranty or liability claims are assumed by the product vendor.

ansi2knr.c is included in this distribution by permission of L. Peter Deutsch, sole proprietor of its copyright holder, Aladdin Enterprises of Menlo Park, CA. ansi2knr.c is

NOT covered by the above copyright and conditions, but instead by the usual distribution terms of the Free Software Foundation; principally, that you must include source code if you redistribute it. (See the file ansi2knr.c for full details.) However, since ansi2knr.c is not needed as part of any program generated from the IJG code, this does not limit you more than the foregoing paragraphs do.

The Unix configuration script "configure" was produced with GNU Autoconf. It is copyright by the Free Software Foundation but is freely distributable. The same holds for its supporting scripts (config.guess, config.sub, ltconfig, ltmain.sh). Another support script, install-sh, is copyright by M.I.T. but is also freely distributable.

It appears that the arithmetic coding option of the JPEG spec is covered by patents owned by IBM, AT&T, and Mitsubishi. Hence arithmetic coding cannot legally be used without obtaining one or more licenses. For this reason, support for arithmetic coding has been removed from the free JPEG software. (Since arithmetic coding provides only a marginal gain over the unpatented Huffman mode, it is unlikely that very many implementations will support it.) So far as we are aware, there are no patent restrictions on the remaining code.

Notices

189

The IJG distribution formerly included code to read and write GIF files. To avoid entanglement with the Unisys LZW patent, GIF reading support has been removed altogether, and the GIF writer has been simplified to produce "uncompressed GIFs".

This technique does not use the LZW algorithm; the resulting GIF files are larger than usual, but are readable by all standard GIF decoders.

We are required to state that

"The Graphics Interchange Format(c) is the Copyright property of CompuServe

Incorporated. GIF(sm) is a Service Mark property of CompuServe Incorporated."

libpng

This projector product includes the open source software program "libpng" which applies the terms and conditions provided by owner of the copyright to the "libpng".

The "libpng" are WITHOUT ANY WARRANTY; without even the implied warranty of


List of libpng programs

libpng-1.2.7

License terms of conditions of each program which are provided by owner of the copyright to the "libpng" are as follows.

For conditions of distribution and use, see copyright notice in png.h Copyright (c)

1998-2004 Glenn Randers-Pehrson (Version 0.96 Copyright (c) 1996, 1997 Andreas

Dilger) (Version 0.88 Copyright (c) 1995, 1996 Guy Eric Schalnat, Group 42, Inc.)

This copy of the libpng notices is provided for your convenience. In case of any discrepancy between this copy and the notices in the file png.h that is included in the libpng distribution, the latter shall prevail.

COPYRIGHT NOTICE, DISCLAIMER, and LICENSE:

If you modify libpng you may insert additional notices immediately following this sentence.

libpng version 1.2.6, September 12, 2004, is Copyright (c) 2004 Glenn

Randers-Pehrson, and is distributed according to the same disclaimer and license as libpng-1.2.5 with the following individual added to the list of Contributing Authors

Cosmin Truta libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright (c)

2000-2002 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.0.6 with the following individuals added to the list of

Contributing Authors

Simon-Pierre Cadieux

Eric S. Raymond

Gilles Vollant and with the following additions to the disclaimer:

190

Notices

There is no warranty against interference with your enjoyment of the library or against infringement. There is no warranty that our efforts or the library will fulfill any of your particular purposes or needs. This library is provided with all faults, and the entire risk of satisfactory quality, performance, accuracy, and effort is with the user.

libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright (c)

1998, 1999 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-0.96, with the following individuals added to the list of

Contributing Authors:

Tom Lane

Glenn Randers-Pehrson

Willem van Schaik libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996,

1997 Andreas Dilger Distributed according to the same disclaimer and license as libpng-0.88, with the following individuals added to the list of Contributing Authors:

John Bowler

Kevin BraceySam Bushell

Sam Bushell

Magnus Holmgren

Greg Roelofs

Tom Tanner libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (c) 1995,

1996 Guy Eric Schalnat, Group 42, Inc.

For the purposes of this copyright and license, "Contributing Authors" is defined as the following set of individuals:

Andreas Dilger

Dave Martindale

Guy Eric Schalnat

Paul Schmidt

Tim Wegner

The PNG Reference Library is supplied "AS IS". The Contributing Authors and Group

42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness for any purpose. The Contributing

Authors and Group 42, Inc. assume no liability for direct, indirect, incidental, special, exemplary, or consequential damages, which may result from the use of the PNG

Reference Library, even if advised of the possibility of such damage.

Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for any purpose, without fee, subject to the following restrictions:

1.

The origin of this source code must not be misrepresented.

2.

Altered versions must be plainly marked as such and must not be misrepresented as being the original source.

3.

This Copyright notice may not be removed or altered from any source or altered source distribution.

Notices

191

The Contributing Authors and Group 42, Inc. specifically permit, without fee, and encourage the use of this source code as a component to supporting the PNG file format in commercial products. If you use this source code in a product, acknowledgment is not required but would be appreciated.

A "png_get_copyright" function is available, for convenient use in "about" boxes and the like: printf("%s",png_get_copyright(NULL));

Also, the PNG logo (in PNG format, of course) is supplied in the files "pngbar.png" and

"pngbar.jpg (88x31) and "pngnow.png" (98x31).

Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the Open Source Initiative.

Glenn Randers-Pehrson [email protected]

September 12, 2004

zlib

This projector product includes the open source software program "zlib" which applies the terms and conditions provided by owner of the copyright to the "zlib".

The "zlib" are WITHOUT ANY WARRANTY; without even the implied warranty of


List of zlib programs

zlib-1.1.4

License terms of conditions of each program which are provided by owner of the copyright to the “zlib” are as follows.

Copyright notice:

(C) 1995-1998 Jean-loup Gailly and Mark Adler

This software is provided 'as-is', without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software.

Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:

1.

The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.

2.

Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.

3.

This notice may not be removed or altered from any source distribution.

Jean-loup Gailly [email protected]

Mark Adler [email protected]

192

Notices

If you use the zlib library in a product, we would appreciate *not* receiving lengthy legal documents to sign. The sources are provided for free but without warranty of any kind. The library has been entirely written by Jean-loup Gailly and Mark Adler; it does not include third-party code.

If you redistribute modified sources, we would appreciate that you include in the file

ChangeLog history information documenting your changes.

libmd5-rfc

This projector product includes the open source software program "libmd5-rfc" which applies the terms and conditions provided by owner of the copyright to the

"libmd5-rfc".

The "libmd5-rfc" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

List of libmd5-rfc programs

libmd5-rfc

License terms of conditions of each program which are provided by owner of the copyright to the "libmd5-rfc" are as follows.

Copyright (C) 1999, 2002 Aladdin Enterprises. All rights reserved.

This software is provided 'as-is', without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software.

Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:

1.

The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.

2.

Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.

3.

This notice may not be removed or altered from any source distribution.

L. Peter Deutsch [email protected]

Independent implementation of MD5 (RFC 1321).

This code implements the MD5 Algorithm defined in RFC 1321, whose text is available at http://www.ietf.org/rfc/rfc1321.txt

The code is derived from the text of the RFC, including the test suite (section A.5) but excluding the rest of Appendix A. It does not include any code or documentation that is identified in the RFC as being copyrighted.

Notices

193

The original and principal author of md5.h is L. Peter Deutsch <[email protected]>.

Other authors are noted in the change history that follows (in reverse chronological order):

2002-04-13 lpd Removed support for non-ANSI compilers; removed references to Ghostscript; clarified derivation from RFC 1321; now handles byte order either statically or dynamically.

1999-11-04 lpd Edited comments slightly for automatic TOC extraction.

1999-10-18 lpd Fixed typo in header comment (ansi2knr rather than md5); added conditionalization for C++ compilation from Martin Purschke

<[email protected]>.

1999-05-03 lpd Original version.

ncurses

This projector product includes the open source software program "ncurses" which applies the terms and conditions provided by owner of the copyright to the "ncurses".

The "ncurses" are WITHOUT ANY WARRANTY; without even the implied warranty of


List of ncurses programs

ncurses-5.6

License terms of conditions of each program which are provided by owner of the copyright to the “ncurses” are as follows.

Copyright (c) 1998-2002,2003 Free Software Foundation, Inc.

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, distribute with modifications, sublicense, and/or sell copies of the

Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT. IN NO EVENT SHALL THE ABOVE COPYRIGHT HOLDERS BE

LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN

ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN

CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE

SOFTWARE.

Except as contained in this notice, the name(s) of the above copyright holders shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Software without prior written authorization.

194

Notices

49

General Notes

147 mDNSResponder

This projector product includes the open source software program "mDNSResponder" which applies the following license terms "Apache License Version 2.0, January

2004".

List of "mDNSResponder"

mDNSResponder-107.6 (only mDNSResponderPosix is used)

License terms “Apache License Version 2.0, January 2004" are as follows.

Apache License

Version 2.0, January 2004 http://www.apache.org/licenses/

TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION

1.

Definitions.

"License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document.

"Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the License.

"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity. For the purposes of this definition, "control" means (i) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity.

"You" (or "Your") shall mean an individual or Legal Entity exercising permissions granted by this License.

"Source" form shall mean the preferred form for making modifications, including but not limited to software source code, documentation source, and configuration files.

"Object" form shall mean any form resulting from mechanical transformation or translation of a Source form, including but not limited to compiled object code, generated documentation, and conversions to other media types.

"Work" shall mean the work of authorship, whether in Source or Object form, made available under the License, as indicated by a copyright notice that is included in or attached to the work (an example is provided in the Appendix below).

"Derivative Works" shall mean any work, whether in Source or Object form, that is based on (or derived from) the Work and for which the editorial revisions, annotations, elaborations, or other modifications represent, as a whole, an original work of authorship. For the purposes of this License, Derivative Works shall not include works that remain separable from, or merely link (or bind by name) to the interfaces of, the Work and Derivative Works thereof.

Notices

195

"Contribution" shall mean any work of authorship, including the original version of the Work and any modifications or additions to that Work or Derivative Works thereof, that is intentionally submitted to Licensor for inclusion in the Work by the copyright owner or by an individual or Legal Entity authorized to submit on behalf of the copyright owner. For the purposes of this definition, "submitted" means any form of electronic, verbal, or written communication sent to the

Licensor or its representatives, including but not limited to communication on electronic mailing lists, source code control systems, and issue tracking systems that are managed by, or on behalf of, the Licensor for the purpose of discussing and improving the Work, but excluding communication that is conspicuously marked or otherwise designated in writing by the copyright owner as "Not a Contribution."

"Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a Contribution has been received by Licensor and subsequently incorporated within the Work.

2.

Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable copyright license to reproduce, prepare

Derivative Works of, publicly display, publicly perform, sublicense, and distribute the Work and such Derivative Works in Source or Object form.

3.

Grant of Patent License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable (except as stated in this section) patent license to make, have made, use, offer to sell, sell, import, and otherwise transfer the Work, where such license applies only to those patent claims licensable by such Contributor that are necessarily infringed by their

Contribution(s) alone or by combination of their Contribution(s) with the Work to which such Contribution(s) was submitted. If You institute patent litigation against any entity (including a cross-claim or counterclaim in a lawsuit) alleging that the Work or a Contribution incorporated within the Work constitutes direct or contributory patent infringement, then any patent licenses granted to You under this License for that Work shall terminate as of the date such litigation is filed.

4.

Redistribution. You may reproduce and distribute copies of the Work or

Derivative Works thereof in any medium, with or without modifications, and in

Source or Object form, provided that You meet the following conditions:

(a) You must give any other recipients of the Work or Derivative Works a copy of this License; and

(b) You must cause any modified files to carry prominent notices stating that

You changed the files; and

(c) You must retain, in the Source form of any Derivative Works that You distribute, all copyright, patent, trademark, and attribution notices from the

Source form of the Work, excluding those notices that do not pertain to any part of the Derivative Works; and

196

Notices

(d) If the Work includes a "NOTICE" text file as part of its distribution, then any

Derivative Works that You distribute must include a readable copy of the attribution notices contained within such NOTICE file, excluding those notices that do not pertain to any part of the Derivative Works, in at least one of the following places: within a NOTICE text file distributed as part of the Derivative Works; within the Source form or documentation, if provided along with the Derivative Works; or, within a display generated by the

Derivative Works, if and wherever such third-party notices normally appear.

The contents of the NOTICE file are for informational purposes only and do not modify the License. You may add Your own attribution notices within

Derivative Works that You distribute, alongside or as an addendum to the

NOTICE text from the Work, provided that such additional attribution notices cannot be construed as modifying the License.

You may add Your own copyright statement to Your modifications and may provide additional or different license terms and conditions for use, reproduction, or distribution of Your modifications, or for any such Derivative

Works as a whole, provided Your use, reproduction, and distribution of the Work otherwise complies with the conditions stated in this License.

5.

Submission of Contributions. Unless You explicitly state otherwise, any

Contribution intentionally submitted for inclusion in the Work by You to the

Licensor shall be under the terms and conditions of this License, without any additional terms or conditions.

Notwithstanding the above, nothing herein shall supersede or modify the terms of any separate license agreement you may have executed with Licensor regarding such Contributions.

6. Trademarks. This License does not grant permission to use the trade names, trademarks, service marks, or product names of the Licensor, except as required for reasonable and customary use in describing the origin of the Work and reproducing the content of the NOTICE file.

7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides the Work (and each Contributor provides its

Contributions) on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS

OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A PARTICULAR PURPOSE. You are solely responsible for determining the appropriateness of using or redistributing the Work and assume any risks associated with Your exercise of permissions under this License.

8.

Limitation of Liability. In no event and under no legal theory, whether in tort

(including negligence), contract, or otherwise, unless required by applicable law

(such as deliberate and grossly negligent acts) or agreed to in writing, shall any

Contributor be liable to You for damages, including any direct, indirect, special, incidental, or consequential damages of any character arising as a result of this

License or out of the use or inability to use the Work (including but not limited to damages for loss of goodwill, work stoppage, computer failure or malfunction, or any and all other commercial damages or losses), even if such Contributor has been advised of the possibility of such damages.

Notices

197

9.

Accepting Warranty or Additional Liability. While redistributing the Work or

Derivative Works thereof, You may choose to offer, and charge a fee for, acceptance of support, warranty, indemnity, or other liability obligations and/or rights consistent with this License. However, in accepting such obligations, You may act only on Your own behalf and on Your sole responsibility, not on behalf of any other Contributor, and only if You agree to indemnify, defend, and hold each Contributor harmless for any liability incurred by, or claims asserted against, such Contributor by reason of your accepting any such warranty or additional liability.


APPENDIX: How to apply the Apache License to your work.

To apply the Apache License to your work, attach the following boilerplate notice, with the fields enclosed by brackets "[]" replaced with your own identifying information. (Don't include the brackets!) The text should be enclosed in the appropriate comment syntax for the file format. We also recommend that a file or class name and description of purpose be included on the same "printed page" as the copyright notice for easier identification within third-party archives.

Copyright [yyyy][name of copyright owner]

Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License.

You may obtain a copy of the License at http://www.apache.org/licenses/LICENSE-2.0

Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR

CONDITIONS OF ANY KIND, either express or implied.

See the License for the specific language governing permissions and limitations under the License.

198

Notices

Index

A

A/V Mute

button, 74, 140

display settings, 91, 97

Accessories, 20

Adapter, audio, 32

Air filter

cleaning, 125

ordering, 20

replacing, 126 to 127

Altitude, 92, 138, 159

Anti-theft device, 20, 98

Aspect ratio, 44, 88, 157

Audio

adapter, 32

cable, 31

connecting equipment, 31 to 34

controlling volume, 76

problems, troubleshooting, 148

turning off (using A/V Mute), 74

Auto Iris setting, 86

Auto Setup setting, 87

B

Background screen settings, 91, 97

Bands, vertical, 146

Batteries, replacing, 132 to 134

Blackboard color mode, 43

Blurry image, 146

Brightness, 157

Brightness setting, 86

Browser control, 118

C

Cables

audio, 31

component-to-VGA, 20, 27, 29 composite, 27

Ethernet, 100

mouse, 25

ordering, 20

security, 98

S-Video, 28

USB, 23 to 25, 35 to 36

VGA, 22, 30

Calibrating, 47 to 49

Capturing image, 96 to 97

Chalkboard, projecting on, 43

Cleaning

air filter, 125

projection window, 124 projector case, 124

Closed captioning, 91

Color

correcting, 43, 86

problems, 147

saturation, 86 settings, 86

Color Mode, 43, 86

Component-to-VGA video cable, 20, 27, 29

Composite video cable, 27

Computer

connecting to, 22 to 23

selecting source, 41

Connecting projector

to audio equipment, 31 to 34

to computer, 22 to 23

to document camera, 35 to 36

to monitor, 26

to USB device, 35 to 36

to video equipment, 27 to 30

199

Contrast ratio, 157

Contrast setting, 86

Control Panel Lock setting, 89, 97 to 98, 139

Custom screen, see User’s Logo

D

Data encryption, 114

Default settings, restoring, 85

DHCP, 152, 153

Dimensions, projector, 17, 158

Direct Power On, 39

Distance from projector to screen, 157

Document camera

connecting, 35 to 36

Documentation, 10 to 11

DVD player, connecting, 27 to 30

Dynamic color mode, 43

E

Easy Interactive Driver, 46 to 47

Easy Interactive Tools

Macintosh, 62 to 71

Windows, 50 to 60

EasyMP Monitor, 99

EasyMP Network Projection

creating password for, 107

data encryption, 114

features, 115

network projection, 99 to 115

problems, 151 to 153

Electrical specifications, 159

E-mail alerts, 115 to 116

Encryption, 111 to 112, 114

Environmental specifications, 159

Epson

accessories, 20

technical support, 11, 155 to 156

warranty, 11 to 170

Error status lights, 138

Ethernet cable, 100 to 102

Extended menu, 91 to 93

E-Zoom buttons, 75

F

FCC compliance statement, 166

Filter, see Air filter

Fn key, notebook, 142

Focusing image, 42

Freeze button, 75

Full aspect setting, 44

H

Help system, using, 136

Help, Epson, 10, 155 to 156

High Altitude mode, 92, 138, 159

I

iBook, connecting to, 22

Image

adjusting, 41 to 44, 85 to 86

blurry, 146

capturing and saving in projector, 96 to 97

correcting shape, 89, 145

fitting on screen, 87, 144 to 145

focusing, 42

problems with, 140 to 147

projecting on chalkboard, 43


size and projection distance, 157

turning off (using A/V Mute), 74 turning off temporarily, 74

zooming, 75

Image menu, 85 to 86

Info menu, 131 to 132

Input Signal setting, 22, 29, 30, 88

Input signal, selecting, 41

Instant Off, 40

Interactive pen, see Pen, interactive

K

Kensington anti-theft device, 20, 98

Keystone correction, 89, 145, 158

Keyword, 107

200

Index

L

Lamp

number of hours used, 131 to 132

ordering, 20

replacing, 127 to 131

specifications, 158

status light, 127, 137 to 138

Lamp timer, resetting, 131

LAN button, 101

Language setting, 93

Laptop computer

connecting to, 22 to 23

display problems, 140 to 144


Light output specifications, 157

Lights, status, 137 to 138

Locking

buttons, 97 to 98 projector, 98

Logo, saving on projector, 96 to 97

M

MacBook, connecting to, 22

Macintosh

display problems, 142

selecting network settings, 110

Manuals, 10

Menus

changing settings, 84 to 85 default settings, restoring, 85

Extended, 91 to 93

Image, 85 to 86

Info, 131 to 132

Network, 101, 105

Reset, 85, 131

Settings, 89 to 90

Signal, 87 to 88

User’s Logo, 96 to 97

Mic Input Level setting, 90

Microphone, connecting, 33

Monitor, connecting external, 26

Monitoring projector

EasyMP Monitor, 99

e-mail notifications, 115 to 116

SNMP, 117 to 118 using browser, 118

Mouse

connecting cable for remote, 25 to 26

using pen as, 49 to 50

using remote control as, 78

N

Network

managing projector remotely, 115 to 119


security, 111 to 114

settings, 100 to 118

wired, 100 to 102

wireless, 103 to 115

No Signal message, 142

Noise level, 158

Normal aspect setting, 44

Not Supported message, 143

Notebook computer, see Laptop computer

Num button, 94

Numeric keypad, using, 94

O

Optical aspect ratio, 44, 157

Options for projector, 20

P

Page Up (+)/Page Down (-) buttons, 78

Page Up/Down setting, 78

Password

Protect sticker, 11

protection, 94 to 95

remote access, 107

request code, 95

Pattern

capturing and saving in projector, 77 to 78

displaying, 76 to 77

selecting, 90

Index

201

Pen, interactive

as mouse, 49 to 50

calibrating, 47 to 49

driver, 46 to 47

parts, 15


replacing batteries, 132

using, 45 to 72

Photo color mode, 43

Picture source, selecting, 41

Picture, see Image

Pointer tool, using, 79 to 80

Position setting, 88, 144

Power

button, 39

specifications, 159

status light, 39, 137 to 138

Power Consumption setting, 89, 127, 132

PowerPoint, 78, 80, 92

Presentation color mode, 43

Presentations

computer, 25 to 26

using the pointer tool, 79 to 80

wireless, 99 to 115

Problems

color, 147

connecting wirelessly, 151 to 153

image, 140 to 147

interactive pen, 148 to 150

network, 151 to 153

no signal, 142

remote control, 154

sound, 148

USB Display, 139

using on-screen help, 136

Progressive format, 88

Projection lamp, see Lamp

Projection setting, 91

Projection window, cleaning, 124

Projector

cleaning, 124

dimensions, 17

disabling buttons, 97 to 98

distance from screen, 157

lamp specifications, 158

monitoring remotely, 115 to 119

options, 20

parts, 13

password protection, 94 to 95

ports, 14

resolution, 157

security features, 93 to 98

specifications, 157 to 159

transporting, 134

troubleshooting, 135 to 156

turning off, 40

turning on, 38 to 39

unpacking, 11 to 12

viewing information about, 131 to 132

Q

Quick Wireless Connection

troubleshooting, 151

using, 105

R

Rear-screen projection, 91

Registration, 11

202

Index

Remote control

A/V Mute button, 74

as wireless mouse, 78

batteries used, 158

batteries, replacing, 133 to 134

connecting cable for mouse, 25 to 26

correcting color, 43, 86

E-Zoom buttons, 75

Freeze button, 75

numeric keypad, using, 94

pointer tool, using, 79 to 80

problems, 154

range, 158 specifications, 158

troubleshooting, 154

USB button, 36, 41

using, 74

virtual over network, 120

Remote Receiver, deactivating, 90

Replacing lamp, 127 to 131

Request code, password, 95

Resetting lamp timer, 131

Resetting menu options, 85

Resize image, 44

Resolution, 44, 143, 157

Resolution setting, 87

S

Safety

instructions, 163 to 165

specifications, 159

Saturation setting, 86

Screen

distance from projector, 157

ordering, 20

startup screen, creating, 96 to 97

Screen image, see Image

Security

cables, 98

Control Panel Lock, 97 to 98 identifying logo, 96 to 97

Kensington lock, 20, 98

network, 111 to 114

password protection, 94 to 95

Settings menu, 89 to 90

Sharpness setting, 86

Signal menu, 87 to 88

Sleep mode, 40, 92, 137, 140

Slide plate, 14

Slideshow

options, 82 running, 80 to 82

SNMP, 117 to 118

Sound, troubleshooting, 148

Source, selecting, 41

Speaker, specifications, 157

Speakers, connecting, 34

Specifications

brightness, 157

dimensions, 158

electrical, 159 environmental, 159

general, 157

lamp, 158 remote control, 158

resolution, 157

safety, 159

speaker, 157

video formats, 160

Sports color mode, 43 sRGB color mode, 43

SSID, 109, 110

Startup screen

creating, 96 to 97 settings, 97

user’s logo, see User’s Logo

Status lights, 137 to 138

Support, see Technical support

S-Video cable, 28

Switching picture source, 41

Sync, adjusting, 88, 146 to 147

T

Tablet PC, 72

Technical support, 11, 155 to 156

Temperature

requirements, 159

status light, 137 to 138

Index

203

Test pattern, 90

Theatre color mode, 43

Through aspect setting, 44

Tint setting, 86

Tracking, adjusting, 88, 146 to 147

Transporting projector, 134

Troubleshooting

blank screen, 140 to 142

cut-off image, 144 to 145

image and sound problems, 140 to 148

network problems, 151 to 153

no signal, 142

projector problems, 135 to 156

remote control problems, 154

wireless projection problems, 151 to 153

Turning off picture (using A/V Mute), 74

Turning off projector, 40

U

Unpacking projector, 11 to 12

USB

button, 36, 41

cable, 23 to 25, 35 to 36 connecting external device, 35 to 36

connecting for display, 23 to 25

key, 105

selecting TypeB port usage, 78, 92

USB Display, solving problems, 139

User button, 90

User’s Logo

creating, 96 to 97

display settings, 97

V

VCR, connecting, 27 to 30

VGA video cable, 22, 30

Video

cables, 11, 20, 27

connecting video equipment, 27 to 30

formats, supported, 160


Video Signal setting, 88

Volume, controlling, 76

W

Warning lights, 137 to 138

Warranty, 11 to 170

Web browser control, 118

Web Remote Control, 120

WEP encryption, 111 to 112

Whiteboard, 35 to 36

Whiteboard color mode, 43

Windows

display problems, 142

selecting network settings, 110

Wired network, 100 to 102

Wireless

module, 103 to 104

presentation, 99 to 115


Quick Wireless Connection, 105

security, 111 to 114

WEP encryption, 111 to 112

WPA security, 113 to 114

Wireless mouse, 25 to 26, 78

Wireless Mouse setting, 79, 92

WPA security, 113 to 114

Z

Zoom aspect setting, 44

Zoom ratio, 157

Zoom setting, 89

Zooming image, 75

204

Index

No results