Samsung AWT19F1B دليل المستخدم

USER’S MANUAL
AWT18F1
AWT19F1
AWT24F1
AWT18A1
AWT19A1
AWT24A1
Series
Series
Series
Series
Series
Series
Window-type Room Air Conditioner (Cooling)
E
PE
DB98-13920A(3)
DB98-13920A-3.indd
17
2006-9-22
10:07:09
Register your product at www.samsung.com/global/register
Safety Precautions
The following safety precautions must be taken when using your air conditioner.
Risk of electric shock. • Can cause injury or death. • Disconnect all
remote electric power supplies before servicing, installing or cleaning.
• This must be done by the manufacturer or its service agent or a similar
qualified person in order to avoid a hazard.
WARNING
DURING OPERATION
DISPOSING OF THE UNIT
OTHERS
u
Users of this product are cautioned not to attempt repair of this product at their
own discretion. Instead, they are requested to directly contact a designated
service center or the outlet at which the product was purchased.
u
Never spill any kind of liquid into the unit. Should this happen, unplug or main
switch off the unit and contact an authorized service center.
u
Do not insert anything between the air outlet blades because the inner fan may
be damaged and could cause injury. Keep children away from the unit.
u
Do not place any obstacles in front of the unit.
u
Do not spray liquid of any kind into the indoor unit. Should this happen, switch off
the breaker used for your air conditioner and contact your installation specialist.
u
Make sure that the unit is correctly ventilated at all times:
Do not place clothing or other materials over it.
u
If the wireless remote control will not be used for a long time, remove the
batteries. (If applicable)
u
When using a wireless remote control, the distance should not be more than 7
meters from the air conditioner. (If applicable)
u
The air conditioner must be plugged into its own specific power source, which
must be installed in compliance with national wiring,earthing and safety
regulations.
u
If the power cord is damaged in any way, it must be replaced by the manufacturer
or its service agent or a similarly qualified person in order to avoid a hazard.
u
This device must be installed according to the national electrical rules.
u
The appliance must be installation that the plug should be easily accessible
after installation.
u
If the fuse on PC board is broken please change it with the type of T 3.15A 250V.
u
The breaker of the air conditioner should be all-pole switch; and the distance
between its two contacts should be no less than 3.5mm. Such means for
disconnection must be incorporation in the fixed wiring.
u
Before throwing out the device, it is necessary to pull back the battery cells and
get rid of them safely for recycling reasons.
u
When you need to dispose of the unit, consult your dealer. If pipes are removed
incorrectly, refrigerant may blow out and come into contact with your skin,causing
injury. Releasing refrigerant into the atmosphere also damages the environments.
u
Please recycle or dispose of the packaging material for this product in an
environmentally responsible manner.
u
Never store or ship the air conditioner upside down or sideways to avoid damage
to the compressor.
u
The appliance is not intended for use by young children or infirm persons without
supervision: Young children should be supervised to ensure that they do not play
with the appliance.
u
Max current is measured according to IEC standard for safety and current is
measured according to ISO standard for energy efficiency.
E-
DB98-13920A-3.indd
2
2006-9-22
10:06:53
Contents
 PREPARING YOUR AIR CONDITIONER
n
n
Safety Precautions.........................................................................................2
Air Conditioning Unit-Main Parts and Control Panel......................................
4
n
Getting Started...............................................................................................
 OPERATION YOUR AIR CONDITIONER
n
5
Cooling Your Room........................................................................................
6
Airing Your Room...........................................................................................
Switching the Air Conditioner Off...................................................................
n Adjusting the Air Flow Direction Horizontally.................................................
n Adjusting the Air Flow Direction Vertically.....................................................
7
7
8
8
n
n
 RECOMMENDATIONS FOR USE
n
n
n
n
Operating Recommendation..........................................................................
Temperature and Humidity Ranges...............................................................
9
9
Cleaning Your Air Conditioner........................................................................10
Solving Common Problems............................................................................12
 METHOD OF INSTALLATION......................................................................
13
E-
DB98-13920A-3.indd
3
2006-9-22
10:06:53
Air Conditioning Unit - Main Parts and Control Panel
e The design and shape are subject to change,
depending on the model.
Inner air flow blades
(right/left orientation)
Air inlet (Inside)
Outer air flow blades
(up/down orientation)
Air inlet (Outside)
Air filter (Inside)
Ventilation lever
Power Cable
E-
DB98-13920A-3.indd
4
2006-9-22
10:06:54
Getting Started
You have just purchased a window-type room air conditioner and it has been installed by your
installation specialist.
Your Owenr’s Instructions contain much valuable information on using your air conditioner.
Please take the time to read them as they will help you take full advantage of the unit’s features.
The booklet is organized as follows.
 The illustration on page 4 shows the air conditioning unit;
it indicates the location and purpose of the main parts and controls on the unit.
 In the manual, you will find a series of step-by-step procedures for each function available.
The illustrations in the step-by-step procedures use four different symbols:
PRESS
PUSH


IMPORTANT
NOTE
E-
DB98-13920A-3.indd
5
2006-9-22
10:06:55
Cooling Your Room
You must select the Cool mode if you wish to lower the temperature
in your room.You can also set the fan speed.
1
Select the operating mode and fan speed.
To cool your room with a...
Set the operating mode
selection dial to...
High fan speed
HI COOL
Between HIGH and LOW
MED COOL
Low fan speed
LOW COOL
Result:
 The air conditioner starts up in the Cool mode.
 The fan starts up at the speed selected.
 You can change modes at any time.
2
To adjust the temperature, turn the temperature control dial
to the desired position.
Possible temperatures: Between 18°C and 29°C inclusive.
Result:
 The air conditioner starts cooling if the room temperature is
higher than the selected temperature.
3
To control the direction of the air flow, refer to page 8.
E-
DB98-13920A-3.indd
6
2006-9-22
10:06:55
Airing Your Room
If the atmosphere in your room is stale, you can air it using the Fan
feature and if necessary, evacuate the stale air outside.
1
If you wish to evacuate stale air outside, push the ventilation lever on the
front of the unit to the right and the open position (
Result:
).
The air inside the room circulates and stale air is evacuated outside.
Otherwise, push the ventilation lever to the left and the closed position (
Result:
2
).
The air simply circulates inside the room.
Set the operating mode selection dial to the HI FAN or LOW FAN
position.
HI FAN: The fan turns high speed.

LOW FAN: The fan turns low speed.
Result:
3
The air conditioner starts up in Fan mode.
To control the direction of the air flow, refer to page 8.
Switching the Air Conditioner Off
You can switch the air conditioner off whenever you want.
1
To switch the unit off, simply set the operating mode selection dial
to the OFF position.
Result:
The air conditioner stops operating.
E-
DB98-13920A-3.indd
7
2006-9-22
10:06:58
Adjusting the Air Flow Direction Horizontally
Depending on the position of the unit in your room, you can adjust the
orientation of the inner air flow blades on the right-hand side of the unit,
thus increasing the efficiency of the air conditioner.
1
Set the air flow blade swing switch to the on position.
Result:
2
The inner blades swing automatically left and right.
To stop the blades moving left and right, set the air flow blade swing
switch to the off position.
 To stop the blades in a specific position and orient the air flow in
the corresponding direction, simply set the switch to the off
position when the blades are in the desired position.
Adjusting the Air Flow Direction Vertically
Again depending on the position of the unit in your room, you can adjust
the orientation of the outer air flow blades on the right-hand side of the unit.
RECOMMENDATION
When...
Adjust the blades to face...
Cooling
Upwards.
Adjust the air flow blades to the desired position, by pushing them upwards or
downwards.
 If you orient the air flow blades downwards and the unit operates in Cool mode
for long periods of time, dew may:
 From on the surface of the blades
 Drip from the blades
E-
DB98-13920A-3.indd
8
2006-9-22
10:06:59
Operating Recommendation
Here is a recommendations that you should follow when using your air
conditioner.
Topic
Recommendation
Power failure
If a power failure occurs when the air conditioner is operating,
the unit is switched off. When the power returns, the air
conditioner starts up again automatically.
Temperature and Humidity Ranges
The following table indicates the temperature and humidity ranges
within which the air conditioner can be used .
Mode
Indoor Temperature
Outdoor Temperature
Indoor Humidity
Cooling
21°C to 32°C approx.
21°C to 54°C approx.
80% or less
If the air conditioner is used at...
Then...
Higher temperature
The automatic protection feature may be triggered and the air
conditioner stopped.
Lower temperature
A water leakage or some other malfunction may happen if the
heat exchanger freezes.
Higher humidity levels
Water way condense on and drip from the surface of the unit if
it is used for long periods.
E-
DB98-13920A-3.indd
9
2006-9-22
10:06:59
Cleaning Your Air Conditioner (TTTTTF1T models)
Be sure to clean the air filter periodically to maintain the air conditioner in
the best condition for a long period of time.
IMPORTANT When cleaning the air conditioner, turn it off and pull out
the power plug.
1
Hold the air filter handle, slightly pull it to the left side and open the front grille.
The removal of the front grille makes it easier to clean the air
conditioner. Open the grille as much as possible.

CAUTION
Removal and Reassembly of the Front Grille
1
Grasp the lower part of the front
grille and the air filter handle,
then open the grille. (The open
angle of front grille has not to be
exceeded 90 degree)
2
Push the front grille on the left
and remove it from the front
panel.
Reassembling of front grille
should be done in reverse
order of disassembly.
3
Front grille
2
Pull the air filter to the right side.
Grille groove
3
Remove all dust on the air filter with a vacuum cleaner or brush.
Body guide
4
When you have finished, insert the air filter back into its original position.
5
Wipe the surface of the unit with a neutral detergent and then wipe it again
with dry cloth.
(Be sure not to use benzene, solvent or other chemical products.)

If you...
Then...
Will not be using the
air conditioner for a
long period of time
 Set the fan going for three to four hours
to dry the inside of the air conditioner
thoroughly.
 Switch the air conditioner off and
unplug it from the wall socket.
 Clean the filter and outer surfaces.
Have not used the air
conditioner for a long
period of time
Set the fan going for a few hours to dry
the inside of the air conditioner thoroughly.
E-10
DB98-13920A-3.indd
10
2006-9-22
10:07:01
Cleaning Your Air Conditioner (TTTTTA1T models)
Be sure to clean the air filter periodically to maintain the air conditioner in
the best condition for a long period of time.
IMPORTANT When cleaning the air conditioner, turn it off and pull out
the power plug.
1
Open the front grille by pulling on the tabs of the unit.
The removal of the front grille makes it easier to clean the air
conditioner. After opening the front grille, lift it up as much as
possible, then pull down to release it.


2
Grasp the handle on the air filter and lift it slightly and then out to the front.
3
Remove all dust on the air filter with a vacuum cleaner or brush.
4
When you have finished, slide the air filter back into position.
5
Clean the outer surfaces with a damp cloth and mild detergent
(do NOT use benzene, solvents or other chemicals).
Wipe them dry with a clean,soft cloth.
If you...
Then...
Will not be using the
air conditioner for a
long period of time
 Set the fan going for a few hours
to dry the inside of the air conditioner
thoroughly.
 Switch the air conditioner off and
unplug it from the wall socket.
 Clean the filter and outer surfaces.
Have not used the air
conditioner for a long
period of time
Set the fan going for a few hours to dry
the inside of the air conditioner thoroughly.
Front grille
Front grille
Grille groove
Body guide
E-11
DB98-13920A-3.indd
11
2006-9-22
10:07:03
Solving Common Problems
Before contacting the after-sales service,perform the following simple checks.
They may save you the time and expense of an unnecessary service call.
Problem
Explanation/Solution
The air conditioner does not
 Check that the circuit breaker used for the air conditioner has not
operate at all
been triggered.
 Check that the power cable is plugged into a wall socket and the
socket is switched on, if necessary.
 Check that the correct operating mode has been selected
(cooling or airing).
The air conditioner does not cool
 Check that the correct operating mode has been selected.
 The room temperature may be too low.
 Dust may be blocking the air filter; refer to page 10 and 11 for
cleaning instructions.
 Check that there is no obstacle blocking the air flow into or out of
the unit.
The air flow direction does not
change when you set the air
 Check that the air conditioner has been switched on;
if necessary, turn the operating mode selection dial.
flow blade swing switch to the
on position
Odours are permeated in the
 Air the room.
room during air conditioning
E-12
DB98-13920A-3.indd
12
2006-9-22
10:07:03
Method of Installation
Before installation, be sure to check the installation area for the air
conditioner, and installation method of the drain hose.
Checkpoints prior to installation
1 Check the cabinet and front grille of the unit for any harmful defects
such as scratches.
2 Be sure to check the power supply.
- Refer to the specifications on the label attached to the unit.
Installation Conditions
1 As the unit is heavy, the wall or window of the installation area should
have sufficient strength and durability for operation of the air conditioner,
and for prevention of any vibration or noise.
If it is weak, reinforcement work should be performed separately.
2 It is advisable to install the air conditioner in the north or west side to
prevent the effect of direct sunlight.
When installing it in the south or east side due to unavoidable
circumstances, it is advisable to install the sunshade to prevent the
direct sunlight.
In this case, take care not to cause any hindrance to the flow of outside air.
3 When installing the air conditioner, be sure to obtain sufficient space on
the rear side of the unit for smooth flow of air.
When operating the air conditioner in closed areas such as inner building
with cooling operation, and result in trouble with the unit.
See the illustration below.
Awning
75mm
min.
500mm
500mm
300mm
260mm
500mm
Fence, wall
or other
obstacle
Approx.3
750mm

150mm min.
 If the wall is greater than 150mm thick,
cut the wall back on a 45° angle if possible.
Outdoor side 45
45
Indoor side
100mm or more
E-13
DB98-13920A-3.indd
13
2006-9-22
10:07:04
Method of Installation(Cont.)
Rear
Rubber cap
Screws(2EA)
Installation of the Drain Tube
Fix the drain tube as shown in the figure.
Gasket
Drain Tube
Installation of the Drain Pan
The procedure for installing the drain pan should be determined by the
condition of the installing area.
 In the case of an area where the drain pan can not be directly
installed on the rear side of the unit after installing the air conditioner.
Example: High storage
1 Open the front grille.
CAUTION
Removal and Reassembly of the Front Grille
1
Grasp the lower part of the front grille and the air filter handle,
then open the grille.
(The open angle of front grille has not to be exceeded 90
degree)
2
Push the front grille on the left and remove it from the front
panel.
3
Reassembling of front grille should be done in reverse order
of disassembly.
2 Remove the front panel.
2-1 Press both sides of the cabinet in the directionof the arrow
as shown in the figure.
2-2 Pull the lower part of the front panel slightly forward.
(below three inches)
2-3 Lift the front panel upward.
Front panel

Applying excessive force to remove the front panel
may cause damage to the tab; be sure not to use
excessive force.
3 Remove four screws on the lower,right and left sides of the unit.
E-14
DB98-13920A-3.indd
14
2006-9-22
10:07:06
Method of Installation(Cont.)
4 Remove the chassis from the cabinet.
Drain Pan
Rear
5 Remove the rubber cap inserted into the basepan.
6 Fix the drain pan as shown in the figure, and then connect the drain hose.
(You can use any commercially-available drain hose.)
7 Install the cabinet at the specified area after installing the drain pan,
and then reassemble it in the original condition.
Rubber cap
Screw
Drain Hose
Bottom-Side View with
Drain Pan and Hose in Place
g When assembling the front panel be sure to fix with a supplied screw.
(TH 2S 4 X 10)
 In the case of an area where the drain pan can be directly installed
on the rear side of the unit after installing the air conditioner.
1 Follow steps 5 and 6 only
If the air conditioner has accessory seal, please install the seal as shown
in the figure
Installation of the accessory seal
Seal Cabi Side ( T40,W50,L430 Qty-2)
Seal Cabi Top ( T30,W40,L700 Qty-1)
Seal Base
( T10,W30,L630 Qty-1)
SEAL - BASE
SEAL - CABI TOP
SEAL - CABI SIDE
SEAL - CABI SIDE
E-15
DB98-13920A-3.indd
15
2006-9-22
10:07:08
Contact SAMSUNG WORLD WIDE
If you have any comments or questions regarding a Samsung products, contact the SAMSUNG
customer care center.
DB98-13920A-3.indd
16
Country
Customer Care Center
Web Site
SOUTH AFRICA
0860 7267864 (SAMSUNG)
www.samsung.com/za
U.A.E
800SAMSUNG (7267864)
www.samsung.com/mea
2006-9-22
10:07:09