SAMSUNG ELECTRONICS CANADA, INC.
HEADQUARTERS
55 Standish Court Mississauga, Ontario L5R 4B2 Canada
TEL: 1-905-542-3535
www.samsung.ca
SERVICE DIVISION
55 Standish Court Mississauga, Ontario L5R 4B2 Canada
1-800-SAMSUNG (1-800-726-7864)
AH68-01694S (Rev 0.0)
YP-C1
- MP3, WMA , Audio ASF and Ogg Playback
- Removable Storage Device
- Direct MP3 Recording
- USB 2.0 Support
- Upgradable
- 42 Hours of Continuous Play
- Voice Recording Function
Contents
I Preparations
Safety Instructions................................................................................................................................................4
Features ..............................................................................................................................................................6
Components ........................................................................................................................................................8
Location of Controls ............................................................................................................................................9
I Connection to Computer
Connecting the player to PC ..............................................................................................................................11
Manual Installation of USB Driver ......................................................................................................................15
Using the removable storage(PC)......................................................................................................................18
● Downloading/Uploading files ........................................................................................................................18
● Disconnecting the USB cable........................................................................................................................18
● Formatting ....................................................................................................................................................19
Installing Media Studio ......................................................................................................................................20
Using Media Studio ............................................................................................................................................21
I Basic Usage
Playing Music and Turning Off the Device ........................................................................................................28
HOLD Function ..................................................................................................................................................29
Recording Voice ................................................................................................................................................29
Recording MP3s ................................................................................................................................................30
Searching for Music/Voice Files ........................................................................................................................32
Setting Bookmark ..............................................................................................................................................33
Listening to FM Radio .......................................................................................................................................34
FM Recording ....................................................................................................................................................36
2
Contents
I Additional Usage
Loop Repeating ..................................................................................................................................................36
MENU Options ..................................................................................................................................................37
Using Navigation ................................................................................................................................................38
Setting Playlist....................................................................................................................................................41
Setting the Advanced Functions ........................................................................................................................42
Selecting the Playmode......................................................................................................................................43
Setting the EQ mode..........................................................................................................................................44
● Preset EQ......................................................................................................................................................44
● Bass Booster ................................................................................................................................................44
● WOW Set ......................................................................................................................................................45
● User EQ Set ..................................................................................................................................................46
Display Settings..................................................................................................................................................47
● Scroll / Display Time......................................................................................................................................47
● Backlight / Contrast ......................................................................................................................................48
● Tag / Bitrate ..................................................................................................................................................49
Language Settings ............................................................................................................................................50
Setting the System ............................................................................................................................................51
Recording Settings ............................................................................................................................................54
Time Settings......................................................................................................................................................55
Managing Files ..................................................................................................................................................56
To Upgrade Firmware ........................................................................................................................................57
I Appendix
MENU Table ......................................................................................................................................................59
I Customer Support
Troubleshooting..................................................................................................................................................60
Specifications ....................................................................................................................................................62
Warranty ............................................................................................................................................................65
3
Safety Instructions
Safety Instructions
Read and understand all the instructions to avoid injury to yourself and damage to the equipment.
Do not expose to extreme temperatures (above 95°F or below 23°F).
Do not expose to moisture.
Do not subject the unit to severe
impact, or place heavy objects
on it.
Do not let any foreign matter spill
into the device.
I Earphones
Follow Traffic Safety Instructions
● Do not use the earphones while driving an automobile or riding a bicycle.
It’s not only dangerous, but also against the law.
● It may cause an accident if you turn up the volume of the earphones while walking.
especially when crossing intersections.
Protect your ears
● Do not turn up the volume too high. Doctors warn against prolonged exposure to high volume.
● Stop using the device or turn the volume down if you have ringing in your ears.
Be careful not to subject the player to excessive pressure when
wearing it round your neck.
Do not expose to chemicals such
as benzene and thinners.
Remove batteries when the
device is left unused for a long
period of time.
I Ambient operating conditions
● Ambient temperature : 5°C ~ 35°C (41°F ~ 95°F)
Humidity : 10 ~ 75%
I Environmental Information
Do not expose to direct sunlight
or heat sources.
Do not store in dusty areas.
Do not try to disassemble and
repair the device yourself.
● Follow local guidelines for waste disposal when discarding packages, batteries,
and old electronic appliances.
● Your player is packaged with cardboard, polyethylene etc., and does not use any unnecessary materials.
✽ Please be aware that we claim no responsibility for damage from data loss
due to breakdown, repair or other causes.
4
5
Features
MP3, WMA , Audio ASF and Ogg Playback
●
The player supports playback of MP3, WMA, Audio ASF and Ogg.
Removable Storage Device
●
You can easily copy and paste files to the player using Windows Explorer.
Features
USB 2.0 Support
●
Upgradeable Firmware
●
Direct MP3 Recording
●
You can convert music from CDs, cassettes, and radio into
MP3 files without a PC.
FM Reception
●
●
6
The 3D surround feature adds spaciousness to the sound.
You can upgrade the built-in programs when available.
Please check the home page (www.samsung.ca) for upgrades.
42 Hours of Continuous Play
●
Listening to an FM program is made easy with Auto Search and
Frequency Memory functions.
SRS WOW Surround Sound
Maximum data speed transfer of 18 Mbps.
This player uses one AA/LR6 alkaline battery. Operation can last up to 42hours.
Actual playing time may vary according to the type and capacity of the battery.
Voice Recording Function
●
You can make high quality voice recordings.
7
Components
Location of Controls
Display
MENU, Navigation button
Volume Up Button
Microphone
Move to Track/Speed Search
Volume Down Button
Carrying Case
Earphone
Neck Strap
Installation CD
Move to Track/Speed Search
Loop Repeating Button
Play/Pause Button
Recording Button
Player
One Battery
User manual
Line In/USB
(1.5V AA/LR6 type)
Model
YP-C1 H
YP-C1 V
YP-C1 X
YP-C1 Z
Built-in memory
128MB
256MB
512MB
1GB
● The capacity of the useable built-in memory is less than indicated as the internal firmware
uses a part of the memory as well.
● Design of accessories is subject to change for the purposes of improvement, without notice.
Neck strap
Hook
Earphone Jack
Battery Cover
Hold Switch
8
ENC/USB Cable Connection Port
Continued...
9
Location of Controls
Connecting the player to PC
▲ System Requirements.
I Display
Equalizer, SRS indicator
Track Number indicator
Play mode indicator
Remaining Battery Power indicator
Play/Stop/Pause indicator
Title (track & artist) indicator
Playtime indicator
Track play indicator
✍ Note
The PC system must meet the
following specifications:
● Pentium 200MHz or greater
● Windows 98 SE/ME/2000/XP
● 40MB of available hard disk space
● CD-ROM drive
(double speed or greater)
● USB port (2.0) supported
● VGA graphic
- Install the operating system in Administrator Account
(main user) for Windows 2000 or XP.
Otherwise, installation will not be completed.
- Windows ME, 2000 and XP can recognize the driver
without installing the provided program. However,
you must install the program in order to format the
player and upgrade firmware.
- If the YP-C1 program has not been installed in
Windows 98, then it will not communicate with your
removable disc. You must install the USB driver file first.
Indicate next track
✍ Note
- The screen pictures are for illustration purposes only. The actual screen may differ.
I Inserting a Battery
1 Slide the cover in the direction of
the arrow to open.
➀
➁
Before connecting the player to PC, make sure to install USB driver. If “Add New Hardware
Wizard” appears, press the [Cancel] button and install the USB driver.
I Installing software
1 Insert the Installation CD
into the CD-ROM drive.
Select [Install Player USB Driver].
2 Insert a battery to the right poles
+ , – and push-close the cover in
the direction of the arrow as indicated.
✍ Note
- Do not place heavy objects on the cover.
10
Continued...
11
Connecting the player to PC
Connecting the player to PC
I Connecting the player to PC with the USB cable
2 Follow the instructions in the window to complete the installation.
1 Connect the USB cable to the USB port on the computer.
2 Connect the other end of the USB cable to the USB cable connection port on
the bottom of the player.
● If you disconnect the USB cable from your PC while implementing a
command or initializing during USB driver installation, your PC may not
function correctly.
3 The USB driver is installed with a message saying that it is searching for a new
device. You may not see the display screen during installation.
Go to the device manager to check that installation has been successfully
completed.
4 Upon installation of the USB driver "Samsung YP-C1 USB Device" will appear in
the [System Properties] ➝ [Device Manager].
USB Cable
12
Continued... 13
Connecting the player to PC
How to check USB driver
Windows 98:
Control Panel ➝ System ➝ Device Manager ➝ Disk Drives ➝ Samsung YP-C1
Windows 2000:
Control Panel ➝ System ➝ Hardware ➝ Device Manager ➝ Disk Drives ➝
Samsung YP-C1 USB Device
Windows XP:
Control Panel ➝ System ➝ Hardware ➝ Device Manager ➝ Universal Serial Bus controllers ➝
Disk Drives ➝ Samsung YP-C1 USB Device
Manual Installation of USB Driver
Go to “Downloading/Uploading files” if the USB driver is installed.
Follow these steps if the USB driver is not installed :
I When an error occurs installation
of the USB driver
1 Check the device manager.
Windows 98,ME:
Control Panel ➝ System ➝ Device Manager
Windows 2000 / XP:
Control Panel ➝ System ➝ Hardware ➝
Device Manager
2 Check if there is a device listed with an
exclamation point or a question mark
(displayed as unknown device or USB device).
3 Double click on the device listed with an exclamation point or a question
mark.
✍ Note
5 When the USB driver is not installed automatically, refer to the next page.
14
- If you are using Windows 2000 and your version of Windows does not recognize the USB driver
please download and install the latest service pack from windowsupdate.microsoft.com
- The installation method may vary depending on the type of PC or operating system.
Contact your PC dealer or service center for installation information.
- If errors occur continuously when you install the USB driver, reconnect the USB cable after
rebooting your system.
15
Manual Installation of USB Driver
4 After selecting the driver,
5 Click [Next].
click [Update Driver].
Manual Installation of USB Driver
I In Windows 98
Follow the instructions in the window to complete the installation.
USB driver location
[CD-ROM]\Win98USB\Drivers
6 Select
[Search for a suitable driver
for my device] and then click [Next].
7 Click [Next] to finish.
: You must reboot your computer to complete the installation.
✍ Note
- You cannot use it as a removable disc in Windows 98 if the YP-C1 program is not installed.
Make sure to install the USB driver file first.
16
17
Using the removable storage(PC)
I Downloading/Uploading files
1 Connect the player to your PC with the supplied USB cable.
2 Open Windows Explorer on PC.
● Removable Disc is displayed in Windows Explorer.
Using the removable storage(PC)
2 When the
[Stop a Hardware device]
message appears, press
the [OK] button and
disconnect the USB cable.
3 Select the file to save and drag-and-drop it into the removable disk icon.
(In numerical, alphabetical order)
● If you change the name of music files in Windows Explorer like 001* * * , 002* * *...,
music files will be played in the order of number indicated.
✍ Notice
- The “WRITING/READING” message will appear during
file download or upload. Disconnecting the USB cable
while “WRITING/READING” is displayed may cause
malfunction of the unit.
I Formatting
1 Select the removable disc icon
and click the right mouse button
to select [Format].
2 Press the [Start] button.
● All saved files will be formatted.
● You can change the name of removable disc
by selecting [Volume label].
- The order of music files is not relative to the replay order
when you select a Removable Disc in Windows Explorer.
I Disconnecting the USB cable
After completing the file transfer, you must disconnect the cable in the following way:
1 Double-click on the green arrow in the taskbar on the
bottom right of the window.
✍ Note
- By formatting, all previously preset menus will be initialized.
- Care must be taken as formatted files can not be recovered.
18
Continued...
19
Installing Media Studio
Media Studio is the program that enables you to download music files to the player, and
play back music files on your PC.
1 Insert the Installation CD into CD-ROM drive.
Select [Install Samsung Media Studio].
Using Media Studio
● Click Media Studio icon from the Desktop.
I Downloading Music Files
1 Connect the player to PC.
2 Select language.
● A device connection window will appear on the right side of the screen.
Select [Device] → [Show device Window] at the top of the screen if device connection
window does not automatically appear.
2 Select the folder with the file(s) you want to transfer from the [Library] window.
● The music files within the folder appear on the center of the screen.
3 Follow the instruction in the window to complete the installation.
Library
window
Device connection
window
20
21
Using Media Studio
3 When music files appear, select the file(s) you want to transfer,
and then press the [Transfer]
button.
● The selected file(s) are transferred to the player.
Using Media Studio
I Formattimg the Player
1 Connect the player to PC.
2 Press the [Device] → [Format] at the top ofthe screen.
3 Press the [Start] button when the Format screen appears.
● The memory of the player is formatted and all the saved files will be deleted.
✍ Note
- Refer to [Help] for more detailed information.
✍ Note
- Refer to [Help] for more detailed information
22
23
Using Media Studio
Using Media Studio
I Ripping Tracks from an Audio CD
I Creating a Folder
1 Insert your CD including tracks to rip into the CD-ROM drive of your PC.
2 Press the [Search Audio CD]
button on the lower part of the screen.
● The tracks on the CD are displayed.
1 Connect the player to the computer.
2 Press the [Create Folder] button at the bottom of device connection window.
3 Enter the name of the new folder when an input screen appears.
● A new folder is created.
● If you open a new folder and transfer a file, the file is transferred to the newly
created folder.
3 Select tracks to be ripped and press the [Rip a CD]
button.
● The selected file is converted into an MP3 file.
● Select [Tools]→[Audio Source Format Conversion Settings] on the top of
the screen to change rip settings.
Change
format
Save path
✍ Note
- Refer to [Help] for more detailed information.
✍ Note
- Refer to [Help] for more detailed information.
24
25
Using Media Studio
I Deleting File
1 Connect the player to the computer.
2 Press the [Delete] button at the bottom of the connection windows after
selecting required files or folders from the device connection windows.
Using Media Studio
Press F1 after starting Media Studio.
● Help will appear.
Click on [Help] at the top of the screen.
● Click on [Help] and the Help window will appear.
3 Press the [Confirm] button when an Confirm Deletion screen appears.
● A selected folder or file is deleted.
✍ Note
✍ Note
- Refer to [Help] for more detailed information.
26
- Music recognition technology and related data are provided by Gracenote and
Gracenote CDDB® Music Recognition ServiceSM.
- CDDB is a registered trademark of Gracenote. The Gracenote logo and logotype, the
Gracenote CDDB logo and logotype, and the "Powered by Gracenote CDDB" logo are
trademarks of Gracenote. Music Recognition Service and MRS are service marks of
Gracenote.
27
Playing Music and Turning Off the Device
I Turning Power On and Off
Power On : Press the
button to turn on the power.
Power Off : Press and hold the
button to turn off the power.
HOLD Function
In Hold mode, all buttons are disabled.
Slide the
switch in the direction of the arrow.
❈ When the button is pressed, the “
HOLD!” message will appear on the display.
I Playing Music (Power On)
Press the
button.
Recording Voice
● Playback starts.
I Pausing Music (Power Off)
Press the
button to pause playback.
● If no buttons are pressed within 10 seconds (changes depending on settings),
the player automatically powers off.
● While in Pause mode, press the
button again to resume playback.
✽ To move to other modes from the Voice mode,
refer to “Changing Mode”.
1 Press and hold the REC button to start voice recording.
2 Press the REC button again to stop the recording and save the voice file.
I Adjusting the Volume
Press
,
to adjust the volume from 00 to 30.
✍ Note
- If the file name is not displayed correctly, move to [Settings] ➔ [Language] ➔ [Menu] and then
change the language setting. When the language setting changes, the language in the menu
screen changes accordingly.
- WMA files can only be played as music files with a compression rate of 48Kbps-192Kbps.
- The power off time can be set in the menu.
28
✍ Note
- The files are recorded in the order of V001,V002......,
and saved as WAV file in the VOICE folder after recording.
- If the Memory is full, Voice Recording is stopped automatically.
- Voice Recording does not work in FM Mode or when the Line In cable is connected.
29
Recording MP3s
Recording MP3s
✽ To move to other modes from LINE_ENC mode,
refer to “Changing Mode”.
3 If the REC button is pressed during recording, the recording stops and an
1 Connect the Audio Output port on the external audio source
(or the Line Out port) to the ENC port on the device with the Line cable.
MP3 file is created.
● The files are recorded in the order of L001, L002....
and saved as MP3 file in LINE_ENC folder after recording.
✍ Note
- Bit Rates can be set within the range of 32Kbps~128Kbps.
- Volume can be adjusted while monitoring the recording.
✍ Notice
- Do not disconnect the Line cable during recording.
- If the battery is not sufficiently charged, the player will not completely record the file.
- Adjust the volume of the external audio source to a suitable level and record it.
If the volume level is too high, the sound quality may be poor.
2 Press and hold the REC button to start MP3 recording.
● If the
button is pressed, recording is paused and if the
the recording resumes.
30
button is pressed again,
31
Searching for Music/Voice Files
▲ To search for specific parts during play
● Press and hold
,
during playback to search for the part you want to listen to.
● Release
,
to resume play normally.
▲ To change tracks during play
● Press
briefly during playback to play the next track.
● Press
briefly within 5 seconds after playback starts, to move to and play the
previous track. Press
briefly after five seconds to play the current track from
the beginning.
Setting Bookmark
1 Press the REC button briefly during playback.
● “lB” mark will be displayed.
● Press
,
within the bookmarked file to
move to the bookmarked locations.
● If the bookmark is set, “B” mark is displayed when playing
files that are not bookmarked.
2 To remove the bookmark, press the REC button once again at the bookmarked.
● “lB” mark will disappear.
▲ To change tracks when stopped
● Press
,
in stop mode to move to the previous/next track.
✍ Note
- VBR(Variable Bit Rate) file: A file that constantly changes the compression rate according
to the type of sounds, such as their pitch, in the file.
- In the case of a VBR file, you cannot move to and play the previous track even if you
press
within 5 seconds after playback starts.
- Files that were downloaded in MP2 or MP1 and had their file extension changed to
MP3 may not play.
32
33
Listening to FM Radio
Listening to FM Radio
First, press the "M" button to display the menu screen and select FM Radio.
I Manual Search for a Frequency
I Searching Stored Frequencies
1 Press the "M" button in FM Mode.
● Press
,
briefly to search manually for
the frequency you want.
● PRESET screen will appear.
2 Use
,
to move to the frequency you want.
I Automatic Search for a Frequency
I Deleting Stored Frequencies
● Press and hold
,
to search for and stop at
frequencies with reception.
1 After moving to the PRESET number you want to delete,
press and hold the A ↔B button.
I Manual Storage of a Frequency
2 After selecting the “Y”, press the "M" button.
● After searching manually for the frequency you want,
press the A↔B button to display the save screen.
● Press
,
to select the number you
want to assign to save the frequency and then
press the A↔B button.
● The saved PRESET number will be deleted.
I Mute Function
1 Press the
I Automatic Storage of a Frequency
● Press and hold the A↔B button while in FM Mode.
● Frequencies within the range of 87.5MHz to
108.0MHz are automatically selected and stored.
● Frequencies are automatically stored, starting from 1.
2 Press the
- To exit from FM Mode, press the "M" button.
- Mono (MO) or Stereo (ST) is automatically selected.
34
button again.
● Mute function is released.
Number of channels saved.
✍ Note
button in FM mode.
● ”MUTE” is displayed and no sound is heard.
✍ Note
- You can store up to 20 frequencies.
- Press the “M” button in the PRESET screen to exit the PRESET mode.
35
FM Recording
MENU Options
1 Press and hold the REC button during FM reception.
● Recording of the currently transmitted FM broadcast begins.
Press and hold the "M" button to switch to MENU mode.
2 Press the REC button again.
Use
● A file is created and the recording stops.
● Files are recording in the order F001, F002, F003...and saved as MP3 files in FM_ENC folder.
,
to move and press the "M" button briefly to select the menu you want.
Press and hold the "M" button to exit the MENU mode.
✍ Notice
- If the battery is not sufficiently charged, the player will not completely record the file.
Loop Repeating
▲ Starting Point
While playing music files, press the A↔B button
briefly at the beginning of the loop you want to set.
● Music : To check the file currently playing.
● FM Radio : To listen to FM radio
● Navigation : To move to Navigation Mode and browse files and folders
● Playlist : To play back only the files you want
● Settings : To set the functions
● Exit : To exit MENU
A↔ appears in the display.
▲ Ending Point
Press the A↔B button briefly again to set the
end of the loop.
A↔B appears in the display.
The loop is played repeatedly.
✍ Note
- Menu mode will be cancelled if no buttons are pressed within 25 seconds
- Language in the menu screen can be changed in [Settings] → [Language] → [Menu].
✍ Note
- Press the A↔B button briefly to cancel the loop.
36
- Loop Repeat is automatically released if you Speed Search with
,
.
37
Using Navigation
You can easily search for files or switch modes using the Navigation function.
1 Press the "M" button to enter Navigation mode.
or press and hold the "M" button to move to Menu and then select
Navigation in Menu.
2 Select the file or folder that you want to play.
●
●
●
: When moving to a higher-level folder.
: When moving to a lower-level folder.
, : When moving to a file or folder in the same directory.
Using Navigation
I Changing Mode
You can change the mode in the following method.
Ex) To change from the Voice mode to the Music mode
1 Press the "M" button in the
Voice mode.
2 Use
to move to the upper folder.
● "M" : Move to the next folder down. When there is not a lower folder,
the selected file will be designated as part of the playlist.
3 Press the
button.
● The selected file will be played.
✍ Note
- Press and hold the "M" button in Navigation mode to exit the Navigation mode.
3 Use
,
to move to the music file you want and press the
button.
● As it is changed to the Music mode, the selected file will be played.
✍ Note
- To change to the FM mode, refer to “Menu Options”.
38
39
Using Navigation
Setting Playlist
I Playing/Exiting Folder
I Setting Playlist
- Move to the file you want in Navigation mode and press the "M" button.
▲ Playing Folder
● The selected file will be marked.
1 Press the "M" button to move to the Navigation mode.
2 Use
,
● When "
to move to the folder you want and press the
● To exit the playlist setting,
move to the marked file in Navigation mode and press the "M" button again.
button.
" appears, the selected file will be played.
I Playing Playlist
▲ Exiting Folder Play
1 Press the "M" button during folder playback to move to the Navigation mode.
2 Use
,
to move to the file you want and press the
● After folder play is released, "
40
button.
1 Press and hold the A↔B button in music mode or select Playlist in Menu.
● The playlist you set will be displayed.
2 Move to the file you want to play and press the
●“
button.
” mark appears and the selected file will be played.
" mark will appear and the selected file will be played.
41
Setting the Advanced Functions
Selecting the Playmode
1 Select Settings in the MENU. (refer to “MENU Options”)
2 In Settings, use
, to move to the function you want and
press the “M” button to select.
● To move to a previous menu, use
or select Return.
1 Select Play Mode in Settings.
2 In Play mode, use
, to move to the mode you want and press
the “M” button to select.
● Normal: To play all the tracks in order one time.
● Repeat One: To repeat one track.
● Repeat All: To repeat all tracks.
● Shuffle All: To play tracks at random.
● Intro: To listen to the first part of all saved tracks for 10 seconds.
● Return: To move to a previous menu
42
43
Setting the EQ mode
1 Select Sound Effect in Settings.
2 In Sound Effect, use , to move to the sound mode you want and press
the “M” button.
Setting the EQ mode
I WOW Set
● Use
, to select the SRS function you want and
then press the “M” button.
● The SRS function is applied only when you select the
SRS, TruBass or WOW in the Preset EQ.
I Preset EQ
● Use , to move to the sound mode you want and then press the “M” button.
● SRS → TruBass → WOW → Normal → Classic → Jazz → Rock → User EQ
● Select User EQ Set to set the EQ as dedired.
● SRS :
● TruBass : This is a bass boost feature that adds fullness
to the sound.
Use , to adjust TruBass from 0 to 10.
● Focus :
I Bass Booster
● Use , to select Bass Booster On or Off and then
press the “M” button.
● Bass Booster function is applied only when you select
Normal, Classic, Jazz or Rock in the Preset EQ.
● On: When the music is played back, the bass is
enhanced in the preset sound.
● Off: Music is played back in the preset sound.
44
You will hear 3D Stereo sound.
Use , to adjust SRS from 0 to 10.
You can enjoy clearer tone during playback.
Use , to set Focus and then
press the “M” button.
High → Middle → Low
● Optimum : Optimize the SRS function according to the device
connected to the main unit.
Use , to move to the connected device and
then press the “M” button.
Earphone → Headphone → Speaker → Car Pack
45
Setting the EQ mode
I User EQ Set
● If User EQ is selected in Preset EQ, EQ can be set to your
preference in the User EQ Set.
● Use
,
to move to right or left and use
, to
adjust the level.
Press the “M” button after completing the setting.
Display Settings
Select Display in Settings.
I Scroll
[ Type ]
● Use
, to select the scroll type.
● Horizontal : Music title moves horizontally.
● Vertical : Music title moves vertically.
[ Speed ]
✍ Note
● Use
, to set the scroll speed from X1 to X5 to adjust
the speed of the track title movement.
-
is a trademark of SRS Labs, Inc.
WOW technology is incorporated under license from SRS labs, Inc..
- Please adjust the volume to a suitable level, as the volume may increase in the SRS setting.
- This unit supports sampling frequencies of 32KHz, 44.1KHz or 48KHz.
I Display Time
● Use
, to select the display time.
● Play Time: Current playback time is displayed.
● Remain Time: Remaining time from total playback time is
displayed.
● Total Time: Total playback time is displayed.
46
47
Display Settings
I Backlight
[ Jog ]
● Use
, to set the
Light-On time from
Off to 60 seconds.
● When set to On, the Light stays on continuously.
[ LCD ]
● Use
, to set the LCD Light-Off time from
Off to 60 seconds
● When set to On, the Light stays on continuously.
Display Settings
I Tag
● Use , to select Tag On or Off.
● On: Display the Tag information if the music file has Tag
information. Display the file name if the music file has no
Tag information.
● Off: Display the name of music file.
I Bitrate
● Use , to select Bitrate On or Off.
● On: Bit rate is displayed at the top of the screen.
● Off: The total number of tracks is displayed at the top of
the screen.
I Contrast
● Use
, to set the contrast from 0 to 10 to adjust the
brightness of the screen.
48
49
Language Settings
Select Language in Settings.
I Menu
● Use , to select the language for displaying menu.
● Chinese(S) → Chinese(T) → Dutch → English → French → German → Hungarian →
Italian → Japanese → Korean → Polish → Portuguese → Russian → Spanish → Swedish
Setting the System
Select System in Settings.
I Resume
● Use , to select Resume On or Off.
● On: Play back music from the part of music you listened last
if you play it back again after stopping.
● Off: Play back music from the beginning of music if you play
it back again after stopping.
I Default vol
I ID3-Tag
● Use , to select the language for displaying Tag information.
● Afrikaans → Basque → Catalan → Chinese(S) → Chinese(T) → Czech → Danish →
Dutch → English → Estonian → Finnish → French → German → Greek → Hrvatski →
Hungarian → Icelandic → Itallian → Japanese → Korean → Norwegian → Polish →
Portuguese → Romany → Russian → Slovak → Slovene → Spanish → Swedish →
Turkish → Vietnamese → Return
● Use , to set the default volume from 0 to 30(Max).
● If the power is turned on again after having adjusted the
volume above the default value, music is played at the
default volume.
● If the power is turned on again after the volume was set to
within the default value, the music is replayed at the previously
played volume.
I Search Speed
● Use , to set the Search Speed from 1sec to 1min.
● When you press and hold
,
to scan a track,
you can adjust the scanning speed.
✍ Note
- What is an ID3 Tag ?
This is what is attached to an MP3 to carry information relevant to the file, such as the title,
artist, album, year, genre and a comment field.
- Supported languages can be changed or added.
50
✍ Note
- For a VBR or Ogg file, the search speed may not be uniform.
51
Setting the System
I Skip Interval
● Use , to set the skip interval from 5sec to 10min.
● If you press
,
in music mode, you can search a track
by a set time.
● In 1 Track setting, you can move to the previous track or the
next track by pressing
,
.
✍ Note
- For a VBR or Ogg file, the skip interval may not be uniform.
I FM Region
● Use , to select FM Region.
● Other Country : Search FM frequency between 87.5MHz to
108.00MHz in the increase of 50 KHz.
● Korea/US : Search FM frequency between 87.5MHz
to108.0MHz in the increase of 100 KHz.
● Japan : Search FM frequency between 76.0MHz to 108.0MHz
in the increase of 100 KHz.
Setting the System
I Default Set
● Use , to select Default Set Yes or No.
● Yes : All settings selected will be initialized.
● No : All settings selected will remain as they are.
I Beep
● Use , to select Beep On or Off.
● On: Beep sounds whenever you press the button.
● Off: No beep sounds when you press the button.
I About
● If you select About, you can check version information,
total number of tracks and remaining capacity.
I FM Search Level
● Use , to select FM Search Level.
● The higher the FM Tuner Sensitivity, the more frequency it
can receive .
● High → Middle → Low
52
53
Recording Settings
Time Settings
Select Record in Settings.
Select Time in Settings.
I Bit Rate
● Use , to set the recording bit rate.
● When recording music into an MP3 file, you can select
one of the following bit rates: 32Kbps, 48Kbps, 64Kbps,
96Kbps and 128Kbps.
I Auto Sync
● Use , to set the Auto Sync Time from 1 to 5 seconds.
● AutoSync Time is a function for separating and saving
MP3 files when there is no sound for a set time during
MP3 recording.
● In SYNC 1 setting, recording stops and it moves to Music
Mode when there is no sound for over 1 second during
recording.
● If AutoSync Time is set to Off, recording keeps going even
if there is no sound, and then it is saved as one file.
54
I Auto Off Time
● Use , to set the Power-Off time from 0 to 30 minites.
● If no button is pressed after play stops, the player will
automatically turn off after the time you set.
● When set to Off, it will not turn off automatically.
I Auto Sleep
● Use , to set the Sleep time to 15, 30, 60, 90, or 120.
The player will automatically turn off after the time you set.
● 15, 30, 60, 90 and 120 minutes are available for
sleep time, and it will automatically turn off after the
time you set.
● When set to Off, it does not turn off automatically.
I Intro Time
● Use , to set the Intro time to 10, 20, 30, or 60 seconds.
● When you select the Intro function, the beginning of all files
will be played back for the seconds you set.
55
Managing Files
Select File in Settings.
I Deleting
1 Select Delete in File.
2 Use , to move to the file you want to delete and
To Upgrade Firmware
1 Connect to http://www.samsung.ca select [SUPPORT] ➝ [DOWNLOAD CENTER]
and then select your product.
2 When the product page appears, select [Firmware] below the model name
to
download the latest firmware.
then press the “M” button.
3 Use
, to move to Confirm and then
press the “M” button.
● The selected file will be deleted.
I Formatting
1 Select Format in File.
2 Use , to move to Confirm and then
press the “M” button.
● The player will be formatted.
✍ Note
- All files will be deleted when formatting the built-in memory.
- It is recommended that formatting be carried out on a PC that has the provided program installed
as formatting in the Menu may take a long time.
56
3 Uncompress the downloaded file in a folder.
4 Run Setup.exe and follow the instructions on the screen for installation.
● If previous version of firmware updater has been installed on your PC,
overwrite the firmware files
(bootmanager.sb,resource.bin,StmpSys.sb,UsbMsc.sb) in "C:\Program
Files\Samsung\YP-C1" folder.
5 Double-click YP-C1 Updater icon on the Desktop.
● Select [Install Player USB Driver] that appears when you insert the Installation
CD into the CD-ROM drive. When the driver is installed, YP-C1 Updater icon
is created on the Desktop.
6 Connect the YP-C1 to your PC.
57
To Upgrade Firmware
MENU Table
7 Check the current version and click the [Start] button of the Firmware Updater
program to upgrade the Firmware.
● If you select "Format data area" and start the update, all the data saved in
YP-C1 will be deleted. Please backup your important data on your PC.
If you do not want your data to be deleted, do not select "Format data area".
8 Confirm the version of the current firmware.
9 Click the [Close] button.
●
58
Use the “M” button to move and select.
59
Troubleshooting
Troubleshooting
The software doesn’t work
The player keeps being turned off.
● Refer to the System Requirements
● In Stop mode, the power is automatically turned off after ten seconds
(changes depending on settings).
● Check to see if there are files saved in it.
The player does not work and the LCD displays nothing.
● Check the battery capacity
● Check to see if the battery is inserted to the right poles ( + , – )
● After connecting it to PC, execute YP-C1 Updater in the desktop to update the product.
In PLAY mode, music is not played after pressing the
● Check to see if MP3 or WMA files are saved in the built-in memory.
● Check to see if the HOLD button is locked.
Files cannot be downloaded.
● Check to see if the driver is installed correctly in the computer.
● Check the connection between the player and PC.
● Check and/or replace the battery, turn on the play's power.
● Operating system limits the number of files you can save.
Please save your music files by creating a subfolder.
● Check if the memory is full.
Backlight does not work.
● Check the backlight setup.
● When the battery power is low, the backlight will go out.
The buttons do not work.
button
Something’s wrong with play time displayed during Play mode.
● Check to see if a VBR file is paying.
LCD window is dark
● Check Contrast
The file name is not displayed correctly.
● Move to [Settings] ➔ [Language] ➔ [ID3-Tag] in the Menu and then change the
language setting.
There is a file saved in the player, but “No File” appears in the screen.
● After checking whether the folder is played, use the Navigation function to change
the folder.
● After connecting it to PC, execute YP-C1 Updater in the desktop to update the product.
I cannot properly connect it to PC.
● Win98 : Try to connect again after installing the driver.
● WinME : Remove the driver program and press the Start in the desktop to execute
Windows Update. After selecting important update and service pack, execute update all.
● Win2000/XP : Try to connect it again after rebooting PC.
● Check setting of Hold switch.
● Remove the battery once and then insert it again.
60
61
Specifications
Model
Built-in Memory capacity
Voltage
Playing time
Dimensions/Weight
Case
Noise Ratio
Earphones Jack Output Power
Output Frequency Range
YP-C1
128MB(YP-C1 H), 256MB(YP-C1 V), 512MB(YP-C1 X), 1GB(YP-C1 Z)
1.5V X 1 (AA/LR6 size alkaline battery)
lasts up to 42hours (Alkaline battery, MP3 128Kbps, Vol level 20)
26 X 71 X 26 mm / 34 g (without battery)
Plastic
85dB with A FILTER
10mW/CH (16 Ω)
20Hz~20KHz
Operating Temperature Range
-5 ~ +35°C(23~95°F)
FM Frequency
87.50 ~ 108.00 MHz
FM Signal to Noise Ratio
FM T.H.D
FM Useable Sensitiivity
File Support
Specifications
The product unit accompanying this user manual is licensed under certain
intellectual property rights of certain third parties. This license is limited to
private non-commercial use by end-user consumers for licensed contents.
No rights are granted for commercial use. The license does not cover any
product unit other than this product unit and the license does not extend to any
unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC
13818-3 used or sold in combination with this product unit. The license only
covers the use of this product unit to encode and/or decode audio files
conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted
under this license for product features or functions that do not conform
to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
60dB
1%
10dB
MPEG1/2/2.5 Layer3(8Kbps ~ 320Kbps, 8KHz ~ 48KHz)
WMA, Audio ASF (48Kbps ~ 192Kbps, 8KHz ~ 48KHz), Ogg
62
63
MEMO
ELECTRONICS
Samsung Limited Warranty
Samsung Electronics Canada Inc. (SECA),
warrants that this product is free from defective material and workmanship.
SECA further warrants that if this product fails to operate properly within the
specified warranty period and the failure is due to improper workmanship or
defective material SECA will repair or replace the product at its option.
All warranty repairs must be performed by a SECA authorized service
centre. (The name and address of the location nearest you can be obtained by
calling toll free 1-800-726-7864 or visiting our web site at www.samsung.ca)
Labour
one (1) year (carry-in)
Parts
one (1) year
On carry-in models, transportation to and from the service centre is the
customer’s responsibility.
The original dated sales receipt must be retained by the customer and
is the only acceptable proof of purchase. It must be presented to the
authorized service centre at the time service is requested.
Exclusions
This warranty does not cover damage due to accident, fire flood and/or
other acts of God; misuse, incorrect line voltage, improper installation,
improper or unauthorized repairs, commercial use, or damage that occurs in
shipping. Exterior and interior finish, lamps and glass are not covered under this
warranty. Customer adjustments which are explained in the instruction manual
are not covered under the terms of this warranty. This warranty will
automatically be voided for any unit found with a missing or altered serial
number. This warranty is valid only on products purchased and used in Canada.
64