User Manual
IPC-630 Series
4U Rackmount
Industrial Chassis
with Alarm Notification
Copyright
The documentation and the software included with this product are copyrighted 2009
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice.
No part of this manual may be reproduced, copied, translated or transmitted in any
form or by any means without the prior written permission of Advantech Co., Ltd.
Information provided in this manual is intended to be accurate and reliable. However,
Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements
of the rights of third parties, which may result from its use.
Acknowledgements
The IPC-630, PCE-7B13, PCE-5B12, PCA-6115, PCA-6114, PCA-6114P4, PCA6114P7, PCA-6114P10, PCA-6114P12, PCA-6114P12X, PCA-6113P4R, PCA6113P7X, AIMB-740, AIMB-742, AIMB-744, AIMB-750, AIMB-760, AIMB-762, AIMB763, AIMB-764, AIMB-766, AIMB-554, AIMB-556 and AIMB-560, AIMB-562, AIMB564 are trademarks of Advantech Co., Ltd.
All other product names or trademarks are properties of their respective owners.
On-line Technical Support
For technical support and service, please visit our support website at:
http://www.advantech.com/support
IPC-630 User Manual
Part No. 2002063001
Edition 2
Printed in China
June 2009
ii
Safety Instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
Read these safety instructions carefully.
Keep this user manual for later reference.
Disconnect this equipment from AC outlet before cleaning. Do not use liquid or
spray detergents for cleaning.
For pluggable equipment, the power outlet shall be installed near the equipment
and shall be easily accessible.
Keep this equipment away from humidity.
Put this equipment on a reliable surface during installation. Dropping it or letting
it fall could cause damage.
Do not leave this equipment in an environment unconditioned where the storage
temperature under 0°C (32°F) or above 40°C (104°F), it may damage the equipment.
The openings on the enclosure are for air convection hence protects the equipment from overheating. DO NOT COVER THE OPENINGS.
Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
Place the power cord such a way that people can not step on it. Do not place
anything over the power cord. The voltage and current rating of the cord should
be greater than the voltage and current rating marked on the product.
All cautions and warnings on the equipment should be noted.
If the equipment is not used for long time, disconnect it from the power source to
avoid being damaged by transient over-voltage.
Never pour any liquid into ventilation openings. This could cause fire or electrical shock.
Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
If any of the following situations arises, get the equipment checked by service
personnel:
a) The power cord or plug is damaged.
b) Liquid has penetrated into the equipment.
c) The equipment has been exposed to moisture.
d) The equipment does not work well or you cannot get it to work according to
user manual.
e) The equipment has been dropped and damaged.
f) The equipment has obvious signs of breakage.
CAUTION: The computer is provided with a battery-powered real-time clock circuit. There is a danger of explosion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended by the manufacture. Discard
used batteries according to the manufacturer’s instructions.
THE COMPUTER IS PROVIDED WITH CD DRIVES COMPLY WITH APPROPRIATE SAFETY STANDARDS INCLUDING IEC 60825.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
iii
IPC-630 User Manual
18. This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
a) This device may not cause harmful interference, and
b) This device must accept any interference received, including interference
that may cause undesired operation.
19. CAUTION: Always completely disconnect the power cord from your chassis
whenever you work with the hardware. Do not make connections while the
power is on. Sensitive electronic components can be damaged by sudden
power surges.
20. CAUTION: Always ground yourself to remove any static charge before touching
the motherboard, backplane, or add-on cards. Modern electronic devices are
very sensitive to static electric charges. As a safety precaution, use a grounding
wrist strap at all times. Place all electronic components on a static-dissipative
surface or in a static-shielded bag when they are not in the chassis.
21. CAUTION: Any unverified component could cause unexpected damage. To
ensure the correct installation, please always use the components (ex. screws)
provided with the accessory box.
A Message to the Customer
Advantech customer services
Each and every Advantech product is built to the most exacting specifications to
ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new Advantech equipment is destined for the laboratory or the factory floor, you can be assured that your product will provide the
reliability and ease of operation for which the name Advantech has come to be
known. Your satisfaction is our primary concern. Here is a guide to Advantech's customer services.
To ensure you get the full benefit of our services, please follow the instructions below
carefully.
Technical support
We want you to get the maximum performance from your products. So, if you run into
technical difficulties, we are here to help. For the most frequently asked questions,
you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones we can give over the phone.
Please consult this manual first. If you still cannot find the gather all the information or
answer questions that apply to your problem, please call your dealer. Please make
sure you have the product close at hand. Our dealers are well trained and ready to
give you the support you need to get the most from your Advantech products. In fact,
most problems reported are minor and are easily solved over the phone.
In addition, free technical support is available from Advantech engineers every business day. We are always ready to give advice on application requirements or specific
information on the installation and operation of any of our products.
IPC-630 User Manual
iv
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For outof-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Initial Inspection
When you open the carton, please make sure that the following materials have been
shipped:
! Chassis
! User Manual
! Warranty Card
! Accessory box with a package of screws (for fastening the disk drives), four rubber pads, 15 pcs rubber cushions (backplane version) or 7 pcs (motherboard
version), one pc of EMI spring shielding (for the backplane version only), a pair
of keys, and a pair of ears.
If any of these items are missing or damaged, contact your distributor or sales representative immediately. We have carefully inspected the IPC-630 mechanically and
electrically before shipment. It should be free of marks and scratches and in perfect
working order upon receipt. As you unpack the IPC-630, check it for signs of shipping
damage. (For example, damaged box, scratches, dents, etc.) If it is damaged or it
fails to meet the specifications, notify our service department or your local sales representative immediately. Also notify the carrier. Retain the shipping carton and packing material for inspection by the carrier. After inspection, we will make arrangements
to repair or replace the unit.
v
IPC-630 User Manual
IPC-630 User Manual
vi
Contents
Chapter
1
General Information ............................1
1.1
1.2
Introduction ............................................................................................... 2
Specifications ............................................................................................ 2
1.2.1 General ......................................................................................... 2
Power Supply Options............................................................................... 3
Table 1.1: Power Supply Options ................................................ 3
Environmental Specifications .................................................................... 3
Table 1.2: Environmental Specifications ..................................... 3
Dimension Diagram................................................................................... 4
Figure 1.1 Dimension diagram..................................................... 4
1.3
1.4
1.5
Chapter
2
System Setup .......................................5
2.1
Removing the Top Cover .......................................................................... 6
Figure 2.1 Removing the top cover.............................................. 6
Installing the Backplane or Motherboard................................................... 7
Figure 2.2 Yellow label indicating copper stub locations ............. 7
Figure 2.3 Installing the backplane .............................................. 8
Figure 2.4 Installing a motherboard ............................................. 8
Installing CPU Card or Add-on Card ......................................................... 9
Figure 2.5 Installing a full-length CPU card ................................. 9
Hold-down Clamp.................................................................................... 10
Figure 2.6 Installing hold-down clamp and rubber cushions...... 10
Figure 2.7 The circular hole on the hold-down clamp................ 10
Installing Disk Drives............................................................................... 11
Figure 2.8 Removing the disk drive housing............................. 11
Figure 2.9 Removing the 3.5" FDD brackets and front covers . 11
Figure 2.10 Installing the disk drives .......................................... 12
Attaching the Ears................................................................................... 12
Figure 2.11Attaching the ears..................................................... 12
2.2
2.3
2.4
2.5
2.6
Chapter
3
Operation............................................13
3.1
The Front Panel ...................................................................................... 14
Figure 3.1 Closed Front panel .................................................. 14
Figure 3.2 Open Front panel..................................................... 14
3.1.1 Switches, Buttons and Front I/O Interfaces ............................... 15
Figure 3.3 Switch, buttons and front I/O interfaces................... 15
3.1.2 LED indicators............................................................................ 16
Table 3.1: LED indicator functions............................................. 16
The Rear Panel ....................................................................................... 17
Figure 3.4 Rear panel of backplane version ............................. 17
Figure 3.5 Rear panel of motherboard version ......................... 17
Replacing the Cooling Fan...................................................................... 18
Figure 3.6 Undo the single screw to remove the fan module ... 18
Figure 3.7 Replacing the fan..................................................... 18
Cleaning the Filter ................................................................................... 19
Figure 3.8 Removing the front door filter .................................. 19
Figure 3.9 Removing the fan filter............................................. 19
Replacing the Power Supply ................................................................... 20
3.5.1 The single power supply model ................................................. 20
Figure 3.10 Replacing the single power supply .......................... 20
3.5.2 The redundant power supply model........................................... 21
3.2
3.3
3.4
3.5
vii
IPC-630 User Manual
Figure 3.11 Replacing 300W redundant power supply module.. 21
Figure 3.12 Replacing 400W redundant power supply module.. 21
Figure 3.13 Power cord plugs orientation on the socket ............ 22
Chapter
4
Alarm Board ...................................... 23
4.1
Alarm Board Layout ................................................................................ 24
Figure 4.1 Alarm board layout .................................................. 24
Alarm Board Specifications..................................................................... 24
Table 4.1: Summary of the connectors on the alarm board ..... 24
Jumper Settings ...................................................................................... 26
Table 4.2: J2, PIC Clear jumper ................................................ 26
Table 4.3: J3, Thermal Sensor jumper ...................................... 26
Table 4.4: J4, Fan Option jumper.............................................. 26
Thermal Sensor ...................................................................................... 26
Figure 4.2 Thermal sensor location .......................................... 26
4.2
4.3
4.4
Appendix A
Exploded Diagrams .......................... 27
A.1
Exploded Diagram .................................................................................. 28
Figure A.1 Exploded diagram of the Backplane version ............ 28
Figure A.2 Exploded diagram of the Motherboard version ........ 29
Appendix B
Backplane & Motherboard Options....... 31
B.1
Backplane Options.................................................................................. 32
Table B.1: PICMG 1.3 Backplane options ................................. 32
Table B.2: PICMG 1.0 Backplane options ................................. 32
Motherboard Options .............................................................................. 33
Table B.3: ATX Motherboard Options........................................ 33
Table B.4: MicroATX Motherboard Options............................... 33
B.2
IPC-630 User Manual
viii
Chapter
1
1
General Information
This chapter provides general
information about the IPC-630.
Sections include:
! Introduction
! Specifications
! Power supply options
! Environment specification
! Dimension diagram
1.1 Introduction
The IPC-630 is a 4U-high 15-slot rackmount industrial computer chassis designed for
mission-critical applications. It supports either backplane or motherboard.
Audible alarm detection and notification with visible LED indicators
The IPC-630 comes with an audible alarm module. It automatically detects the system operating conditions, such as power, fan, temperature, and HDD, and displays
the system status on the front visible LED indicators. Once any failure happens, the
alarm module will make a beep to warn users to take necessary actions. This feature
reduces the system downtime. Unique alarm detection and notification to reduce system down time.
Outstanding ID and mechanical design
Unlike the classical industrial computer, IPC-630 has an innovative appearance for
an industrial computer chassis. The flexible mechanical design supports a single PS/
2 or redundant power supply using a power bracket replacement. The shockproof
disk drive housing and the rubber cushions protect the system against harsh industrial environments or unexpected shocks. The lockable front door prevents unauthorized access to data storage. All these outstanding features make the IPC-630 an
ideal solution for the price, performance and total cost of ownership.
1.2 Specifications
1.2.1 General
!
!
!
!
!
!
!
!
!
!
Construction: Heavy-duty steel
Disk drive capacity: three 5.25" disk drives (CD-ROM or CD-R/W drive or
DVD-ROM drive), one 3.5" FDD, and one internal 3.5" disk drive
Front I/O interfaces: Dual USB port and a reserved 9-pin D-SUB opening
Rear I/O interfaces: a reserved 9-pin D-SUB opening for the backplane version; five reserved 9-pin D-SUB and a 68-pin SCSI openings for the motherboard version
LED Indicators: Bi-color LEDs (green/red) for Power, Temperature, and Fan
status; single-color LEDs (green) for HDD activity
Switch and Buttons: System Reset button, Alarm Reset button, and Power
switch
Cooling fan: One 114 CFM (12 cm x 12 cm) cooling fan with air filter near the
front left of the chassis.
Air Filters: Two easily maintained reusable filters near the front of the system
fan and behind the front door
Gross Weight: 18 kg (39.6 lb)
Dimensions (WxHxD):
– Backplane version: 482 mm x 177 mm x 452 mm (19" x 7" x 17.8");
– Motherboard version: 482 mm x 177 mm x 502 mm (19" x 7" x 19.8")
IPC-630 User Manual
2
Table 1.1: Power Supply Options
PS-300ATX-ZBE
RPS-300ATX-ZE
Watt
300 W max. (ATX, PFC)
(single PS/2)
300 W max. (ATX, PFC)
(1+1 redundant)
Input rating
100 ~ 240 Vac (Full range)
100 ~ 240 Vac (Full range)
Output voltage
+5 V @ 30 A, +3.3 V @ 28 A,
+12 V @ 15 A, -5 V @ 0.3 A,
-12 V @ 0.8 A, +5 Vsb @ 2 A
+5 V @ 25 A, +3.3 V @ 18 A, +12
V @ 16 A, -5 V @ 0.5 A,
-12 V @ 0.5 A, +5 Vsb @ 2 A
Minimum load
+5 V @ 0.1 A, +3.3 V @ 0.3 A
+5 V @ 3 A, +3.3 V @ 1 A, +12 V
@ 2 A, +5 Vsb @ 0.1 A
MTBF
100,000 hours @ 25° C
100,000 hours @ 25° C
Safety
UL/TUV/CB/CCC
UL/TUV/CB/CCC
Model Name
PS-400ATX-ZBE
RPS-400ATX-ZE
Watt
400 W max. (ATX, PFC)
(single PS/2)
400 W max. (ATX, PFC)
(1+1 redundant)
Input rating
100 ~ 240 Vac (Full range)
100 ~ 240 Vac (Full range)
Output voltage
+5 V @ 35 A, +3.3 V @ 25 A,
+12 V @ 30 A, -5 V @ 0.8 A,
-12 V @ 1 A, +5 Vsb @ 2 A
+5 V @ 35 A, +3.3 V @ 25 A, +12
V @ 28 A, -5 V @ 0.5 A,
-12 V @ 1.2 A, +5 Vsb @ 2 A
Minimum load
+5 V @ 3 A, +3.3 V @ 1 A, +12 V
@ 1 A, +5 Vsb @ 0.1 A
+5 V @ 3 A, +3.3 V @ 1 A,
+12 V @ 2 A, +5 Vsb @ 0.1 A
MTBF
91,000 hours @ 25° C
100,000 hours @ 25° C
Safety
UL/TUV/CB/CCC
UL/TUV/CB/CCC
1.4 Environmental Specifications
Table 1.2: Environmental Specifications
Environment
Operating
Non-operating
Temperature
0 to 40°C (32 to 104°F)
-20 to 60°C (-4 to 140°F)
Humidity
10 to 85% @ 40°C, non-condensing
10 to 95% @ 40°C, non-condensing
Vibration
1G rms
2G
Shock
10G (with 11 ms duration, half
sine wave)
30G
Safety
CE compliant
3
IPC-630 User Manual
General Information
Model Name
Chapter 1
1.3 Power Supply Options
1.5 Dimension Diagram
Motherboard
Backplane
Unit: mm [inch]
Figure 1.1 Dimension diagram
IPC-630 User Manual
4
Chapter
2
2
System Setup
This chapter introduces the
installation process.
Sections include:
! Installing the backplane or
motherboard
! Installing the CPU card or
add-on card
! Installing disk drives
! Attaching the ears and handles
The following procedures guide users to install the backplane, motherboard, add-on
cards, and disk drives into the chassis. Please also refer to Appendix A, Exploded
Diagram, for the detailed parts of the chassis
Note!
Use caution when installing or operating the components with the chassis open. Be sure to turn off the power, unplug the power cord and
ground yourself by touching the metal chassis before you handle any
components inside the machine.
2.1 Removing the Top Cover
Please refer to Figure 2.1 and proceed as below.
1. Detach the four screws on the left and right of the chassis.
2. Remove the top cover rearwards gently.
Figure 2.1 Removing the top cover
IPC-630 User Manual
6
NUT NUMBER
BP/MP MODEL
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
X
A M
PCA-6113P4R
PCA-6114P7
PCA-6114P12
PCA-6114P4
PCA-6114P10
PCA-6114-B
PCA-6113P7X
PCA-6115
PCA-6114P12X
PCE-7B13-64
PCE-5B12-64
AIMB-740
AIMB-742
AIMB-744
AIMB-750
AIMB-760
AIMB-762
AIMB-764
AIMB-542
AIMB-554
AIMB-556
AIMB-560
AIMB-562
Be careful to screw the Copper Stub under 10 kgf cm.
Figure 2.2 Yellow label indicating copper stub locations
7
IPC-630 User Manual
System Setup
The IPC-630 supports either up to 15-slot backplane or ATX/microATX motherboard.
To install the backplane or motherboard, please proceed as follows:
1. Dismantle the hold-down clamp by undoing the two screws on its both ends.
2. There is a yellow warning label located inside of the chassis bottom. (see Figure
2.2) It shows the screw locations for attaching the various backplanes or motherboards. Be sure to follow the instruction and fasten the backplane or motherboard onto the chassis with the correct screw locations.
3. While installing a BACKPLANE, fasten it in place and attach the supplied EMI
spring shielding with the screws provided.
4. For the PICMG 1.0 BACKPLANE, connect the orange-white wire from connector, HCN1, on the backplane to connector, CN21, on the CPU card.
5. While installing a MOTHERBOARD, attach the motherboard I/O shielding onto
the rear plate first. Then fasten the motherboard onto the chassis.
6. Connect the 20-pin (or 24-pin) ATX power connector and the 4-pin +12V power
connector from the power supply to the backplane or the motherboard. (For the
PICMG 1.0 BACKPLANE, the 4-pin +12 V power connector is connected to the
CPU card.)
7. Connect the 9-pin USB wire, PS/2 wire, Power switch wire, and the System
Reset switch wire from the chassis to the motherboard.
8. Connect the wire of HDD LED from the chassis to the motherboard.
Chapter 2
2.2 Installing the Backplane or Motherboard
Figure 2.3 Installing the backplane
Figure 2.4 Installing a motherboard
IPC-630 User Manual
8
Figure 2.5 Installing a full-length CPU card
9
IPC-630 User Manual
System Setup
IPC-630 supports up to 15 add-on cards. To install a CPU card or add-on card,
please proceed as follows:
1. Select a vacant PICMG slot for the full-length CPU card, or a PCI/ISA slot for
other add-on cards. Then, remove the corresponding I/O bracket attached to the
rear plate of the chassis.
2. Insert the CPU card (with CPU, CPU cooler, RAM, and necessary cables
installed) or add-on card vertically into the proper slot (See Figure 2.5). For fulllength cards, please make sure that the card bracket has been inserted properly
and the other edge of the card has been inserted into the plastic guiding fillister.
Fasten the card with the screw on top of the I/O bracket.
3. Repeat Step 1 and 2 if there is more than one add-on card to be installed.
4. Connect the 9-pin USB wire, PS/2 wire, power switch wire and the System
Reset switch wire from the chassis to the CPU card.
5. Connect the wire of HDD LED from the chassis to the CPU card.
6. For the PICMG1.0 Backplane, connect the orange-white wire from the connector CN20 on the CPU card to the connector, HCN1, on the backplane. Connect
the 4-pin +12 V power connector from the power supply to the CPU card.
Chapter 2
2.3 Installing CPU Card or Add-on Card
2.4 Hold-down Clamp
The hold-down clamp protects all the cards from vibration and shock. After inserting
all the cards, re-fasten the hold-down clamp according to the following steps.
1. There are two rows of notches on both sides of the hold-down clamp for inserting into rubber cushions provided in the accessory. One side is for PCI cards,
while the other side is for ISA cards. Depending on the card height, the cushions
can be inserted upward or downward. After the rubber cushions have been
inserted into the notches, they will stabilize the add-on cards to protect them
from shock and vibration. (see Figure 2.6)
2. Put the hold-down clamp back into its original position. Please note that the circle hole on the hold-down clamp faces left rear. (See Figure 2.7).
3. Secure the hold down clamp to the chassis with the two screws.
Figure 2.6 Installing hold-down clamp and rubber cushions
Figure 2.7 The circular hole on the hold-down clamp
IPC-630 User Manual
10
Figure 2.8 Removing the disk drive housing
Figure 2.9 Removing the 3.5" FDD brackets and front covers
11
IPC-630 User Manual
System Setup
The disk drive housing supports three 5.25" and two 3.5" disk drive devices. Please
follow these steps for installation.
1. Undo the four screws on the top of the disk drive housing and then lift it up. (see
Figure 2.8)
2. Loosen the two screws on top left of the housing to remove the brackets for fixing the 3.5" FDD or HDD. And then remove the screws on both sides of the front
covers in case the user needs to install the front-accessible disk drives. (see
Figure 2.9)
3. Insert the disk drives into the proper location in the disk drive housing, and
secure them with the supplied screws. (see Figure 2.10)
4. Connect the suitable cables (ex. IDE, SCSI, SATA or SAS, etc.) from the CPU
card or motherboard to the various disk drives.Then plug the power connector
into each disk drive.
5. Replace the disk drive housing and fasten it with the four screws.
Chapter 2
2.5 Installing Disk Drives
Figure 2.10 Installing the disk drives
2.6 Attaching the Ears
There is a pair of ears for the front panel in the accessory box. If you need to install
the chassis on the rack, please refer to Figure 2.11 to simply fasten them to the frontright and front-left edges with the four screws provided. If you have prepared the slide
rails and plan to attach them onto the chassis, please detach the decorated bars on
both sides of the chassis first.
Figure 2.11 Attaching the ears
IPC-630 User Manual
12
Chapter
3
3
Operation
This chapter introduces the system operation information.
Sections include:
! The front panel
! The rear panel
! Replacing the cooling fan
! Cleaning the filter
! Replacing the power supply
3.1 The Front Panel
The front panel features the lockable door and four LED indicators. The user can
close the door with or without the key with the user-friendly rotary lock. When opening the door, there is a System Reset button, an Alarm Reset button, a momentary
power switch, a dual USB port and a reserved 9-pin D-SUB opening. The individual
functions are described as below.
Figure 3.1 Closed Front panel
Figure 3.2 Open Front panel
IPC-630 User Manual
14
Switches, Buttons and Front I/O Interfaces
Chapter 3
3.1.1
Operation
Figure 3.3 Switch, buttons and front I/O interfaces
Three switches are located on the front plate, behind the front door.
System Reset button: Press this button to reboot the system.
Alarm Reset button: Whenever a fault occurs in the system (e.g., fan failure or the
temperature in the chassis is too high), an audible alarm will be activated. Pressing
this button will stop the alarm from beeping.
Momentary Power switch: Press this switch to turn the system power on or off.
Please use system shutdown or press this switch for few seconds to turn off the system ATX power.
Dual USB port: For connecting a wide range of USB devices for data transfer,
backup or input.
9-pin D-SUB opening: Reserved for a 9-pin COM port.
15
IPC-630 User Manual
3.1.2
LED indicators
Four LEDs (see Figure 3.4 above) are placed on the left side of the front panel on the
IPC-630 chassis to indicate system health and activity. Please refer to Table 3.1 for
the LED definition summary.
Table 3.1: LED indicator functions
LED
Description
Green
Red
Power
System power
Normal
Abnormal
Fan
Cooling fan status
Normal
Abnormal
Temperature
Temperature in the
chassis
Normal
Abnormal
Hard Disk
Hard disk drive activity
Data access
No light
When the system powers is on, the power LED is always Green.
When the power LED is RED, it indicates a redundant power supply module failure.
To stop the alarm beep, press the Alarm Reset button. Examine the redundant
power supply module right away and replace the failed module with a good one.
When the fan LED is RED, it indicates a failed cooling fan, and the alarm is also activated. To stop the alarm beep, press the Alarm Reset button and then replace the
failed fan with a good one immediately.
If the temperature LED is RED, it means that inside of the chassis is overheated. An
audible alarm will be activated. Press the Alarm Reset button to stop the alarm beep.
Inspect the system fan and its filter and the rear of the chassis immediately. Make
sure the airflow inside the chassis is smooth and not blocked by dust or other particles.
IPC-630 User Manual
16
For the backplane version, the rear plate includes with 15-slot I/O brackets and a
reserved 9-pin D-SUB opening. (see Figure 3.4). For the motherboard version, the
rear plate includes with 7-slot I/O brackets, 5 reserved 9-pin D-SUB openings and a
68-pin SCSI opening. (see Figure 3.5).
Chapter 3
3.2 The Rear Panel
Operation
Figure 3.4 Rear panel of backplane version
Figure 3.5 Rear panel of motherboard version
There is a ground screw with a washer located on the lower right of the rear panel.
This will protect the system in case the electric leakage happens.
17
IPC-630 User Manual
3.3 Replacing the Cooling Fan
There is one cooling fan located on the front left of the chassis. The fan provides the
system with ample cooling by blowing air toward the rear. If the fan fails, the alarm
will beep. Simply press the Alarm Reset button to stop the alarm and replace the
failed fan right away. Please proceed according to the instructions below.
1. Remove the top cover.
2. Unplug the fan power connector.
3. Undo the screw on top of the fan module and take the fan module out. (see Figure 3.6)
4. Loosen four screws on the fan bracket and the four screws on the fan guard (not
the screws on the fan) and replace it with a new fan. (see Figure 3.7)
5. Attach the new cooling fan on the bracket and fan guard by screwing in the eight
screws.
6. Reconnect the fan power connector.
7. Replace the fan module into the chassis and then screw the one screw onto the
chassis.
Figure 3.6 Undo the single screw to remove the fan module
Figure 3.7 Replacing the fan
IPC-630 User Manual
18
Figure 3.8 Removing the front door filter
Figure 3.9 Removing the fan filter
19
IPC-630 User Manual
Operation
The filter prevents dust or particles from entering the work environment and extends
longevity of the system. It's better to clean the filters periodically. There are two reusable filters behind the front door and the left front of the chassis. To remove and clean
the filter, proceed as follows.
1. Open the front door.
2. Pull out the filter behind the front door by pushing the two clips; pull out the fan
filter by pushing the hook and then slide it to the right. (see Figure 3.8 and 3.9)
3. Clean the filters by a soft brush or wash the dust away from the filter with running water, then dry it.
4. Replace them inside the unit.
Chapter 3
3.4 Cleaning the Filter
3.5 Replacing the Power Supply
The IPC-630 supports either a PS/2 single power supply or a redundant power supply. To replace the power supply, please proceed:
3.5.1
The single power supply model
To replace the single power supply, please follow these instructions:
1. Unplug the power cord from the power supply.
2. Remove the top cover and the hold-down clamp.
3. Unplug the 20-pin (or 24-pin) ATX power connector and 4-pin +12V power connector from the backplane. And unplug other power connectors from the disk
drives.
4. Remove the four screws located on the power supply bracket and the two
screws inside of the left plate and then remove the power supply. (see Figure
3.10)
5. Place a new power supply into the power supply bracket and fasten it with the
six screws.
6. Plug the 20-pin (or 24-pin) ATX power connector and 4-pin +12V power connector to the backplane. And plug other power connectors to the essential disk
drives.
7. Replace the hold-down clamp and top cover. Plug in the power cord.
Figure 3.10 Replacing the single power supply
IPC-630 User Manual
20
The redundant power supply model
Figure 3.11 Replacing the 300W redundant power supply module
Figure 3.12 Replacing the 400W redundant power supply module
21
IPC-630 User Manual
Operation
In this configuration, there is a redundant power supply with two modules which are
hot-swappable. To replace the redundant power supply module, please follow these
instructions:
1. Turn off the power switch of the failed power supply module. Then loosen the
screw on it and then grab the handle to gently pull it out. (see Figure 3.11 & Figure 3.12)
2. Make sure that the new power supply module is the same rating as the currently
installed one.
3. Slide the new power supply module inward until it locks into the right position.
4. Secure the screw and replace the handle.
Chapter 3
3.5.2
Note!
When you plug two power cords into the same bank of sockets,
please align them in the same direction (see Figure 3.13).
Figure 3.13 Power cord plugs orientation on the socket
IPC-630 User Manual
22
Chapter
4
4
Alarm Board
This chapter introduces the alarm
board and thermal sensor specifications.
Sections include:
! Alarm board layout
! Alarm board specifications
! Thermal sensor
The alarm board is located under the system fan. The alarm board makes an audible
alarm if:
!
Any power supply module of redundant power supply fails
!
The system fan fails
!
Internal temperature of the chassis rises too high
To stop the alarm beep, simply press the Alarm Reset button on the front panel.
4.1 Alarm Board Layout
The layout and detailed specifications of the alarm board are given below:
Figure 4.1 Alarm board layout
4.2 Alarm Board Specifications
Input Power: +5V, +12V
Input Signals:
! 2 fan connectors
! One thermal sensor connector
! One power good input
! One alarm reset input
! One voltage signal connector (optional, connect from power supply, includes +/12V, +/-5V, +3.3V)
! One HDD LED connector (connect from the CPU card/motherboard)
Output Signals:
! One LED board connector (optional)
Pin Definition:
Table 4.1: Summary of the connectors on the alarm board
CN1: Auxiliary External Power Connector, standard mini 4-pin power connector
Pin 1
+5 V
Pin 3
GND
Pin 2
GND
Pin 4
+12 V
Pin 2
HLED_ACT
Pin 2
TEMP
CN3: External HDD LED connector
Pin 1
VCC
CN4: Thermal sensor connector
Pin 1
IPC-630 User Manual
GND
24
CN5: Power LED connector
Pin 1
Power Good
Power Fail
Pin 2
TEMP Fail
Pin 2
Fan Fail
Pin 2
GND
CN6: Temperature LED connector
Pin 1
TEMP Good
CN7: Fan LED connector
Pin 1
Fan Good
CN8: HDD LED connector
Pin 1
HDD
CN13: Voltage detect input connector
Pin 1
5 VSB
Pin 5
+5 V
Pin 2
GND
Pin 6
+3.3 V
Pin 3
GND
Pin 7
-12 V
Pin 4
-5 V
Pin 8
+12 V
Pin 2
SDA
Pin 2
Power Fail
Pin 2
Alarm Reset
CN15: I2C connector
Pin 1
SCL
CN16: Power Good input
Pin 1
GND
CN17: Alarm Reset connector
Pin 1
GND
CN18: LED Board connector
Pin 1
GND
Pin 9
Temperature Good
Pin 2
+5 V
Pin 10
Temperature Fail
Pin 3
+12 V
Pin 11
Fan Good
Pin 4
-5 V
Pin 12
Fan Fail
Pin 5
-12 V
Pin 13
N/A
Pin 6
HDD
Pin 14
+3.3 V
Pin 7
Power Good
Pin 15
5VSB
Pin 8
Power Fail
Pin 3
FAN_DEC1 (FAN1)
FAN1 & FAN2: Fan power connector
Pin 1
GND
Pin 2
+12V
FAN_DEC2 (FAN2)
J1: PIC Program connector
Pin 1
GND
Pin 4
TEMP
Pin 2
MCLR#
Pin 5
VCC
Pin 3
ICSPCLK
25
IPC-630 User Manual
Alarm Board
Pin 2
Chapter 4
Table 4.1: Summary of the connectors on the alarm board
4.3 Jumper Settings
Table 4.2: J2, PIC Clear jumper
Normal
Open (default)
Clear
Short
Table 4.3: J3, Thermal Sensor jumper
One sensor
Open (default)
Disable
Short
Table 4.4: J4, Fan Option jumper
One fan
Open (default)
Two fans
Short
4.4 Thermal Sensor
There is a thermal sensor near the left rear of the chassis. Please refer to Figure 4.2
to find the location.
thermal sensor
Figure 4.2 Thermal sensor location
If the machine overheats, the temperature sensor will send a signal to the alarm
board and a continuous alarm will sound. To stop the alarm from beeping, press the
Alarm Reset button on the front panel.
IPC-630 User Manual
26
Appendix
A
A
Exploded Diagrams
A.1 Exploded Diagram
Figure A.1 Exploded diagram of the Backplane version
IPC-630 User Manual
28
Appendix A Exploded Diagrams
Figure A.2 Exploded diagram of the Motherboard version
29
IPC-630 User Manual
IPC-630 User Manual
30
Appendix
B
B
Backplane and
Motherboard Options
B.1 Backplane Options
IPC-630 supports a variety of up to 15-slot backplanes. Users can contact a local
sales representative for detailed specification and information.
Table B.1: PICMG 1.3 Backplane options
Model Name
Segment
PCE-7B13
PCE-5B12
Slots
SHB*
PCIe x16
PCIe x 8
PCI-X
PCI
Single
1
-
2
6
4
Single
1
1
-
6
4
*SHB: System Host Board
Table B.2: PICMG 1.0 Backplane options
Model Name
Segment
PCA-6114
Slots
PICMG
PICMG/PCI
PCI
ISA
Single
-
-
-
14
PCA-6114P4
Single
2
-
4
8
PCA-6114P7
Single
3
1
6
4
PCA-6114P10
Single
2
-
10
2
PCA-6114P12
Single
1
1
11
1
PCA-6114P12X
Single
1
1
11
1
PCA-6113P4R
Single
2
-
4
7
PCA-6113P7XE
Single
2
-
7
4
IPC-630 User Manual
32
IPC-630 supports a variety of Advantech ATX/microATX motherboards as below. You
can contact a local sales representative for detailed information.
Table B.3: ATX Motherboard Options
Model Name
Bus
PCI
PCI/ISA
ISA
AGP
SATA
AIMB-742
4 (32-bit)
1
1
1 (8X)
-
AIMB-744
2 (PCI-X 64-bit)
4 (PCI 32-bit)
-
-
1 (8X)
2
AIMB-750
2 (PCI-X 64-bit)
4 (PCI 32-bit)
-
-
1 (4X)
2
AIMB-762
1 (PCIe 16X)
1 (PCIe 4X)
5 (PCI 32-bit)
-
-
-
4
AIMB-763
1 (PCIe 16X)
1 (PCIe 1X)
5 (PCI 32-bit)
-
-
-
4
AIMB-764
1 (PCIe 16X)
1 (PCIe 4X)
5 (PCI 32-bit)
-
-
-
5
AIMB-766
1 (PCIe 16X)
2 (PCIe 1X)
4 (PCI 32-bit)
-
-
-
6
Table B.4: MicroATX Motherboard Options
Model Name
Bus
PCI
AGP
SATA
AIMB-564
1 (PCIe x16),
1 (PCIe x4),
2 (PCI 32-bit)
-
7
AIMB-562
1 (PCIe x16),
1 (PCIe x1),
2 (PCI 32-bit)
-
4
AIMB-560
3 (PCI 32-bit)
-
4
AIMB-556
1 (PCIe x16),
1 (PCIe x4),
2 (PCI 32-bit)
-
4
AIMB-554
1 (PCIe x16),
1 (PCIe x4),
2 (PCI 32-bit)
-
2
AIMB-542
3 (PCI 32-bit)
1
2
33
IPC-630 User Manual
Appendix B Backplane and Motherboard Options
B.2 Motherboard Options
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2009