Compaq ProLiant SL165s Specifications

HP ProLiant DL165 G7 Server
Maintenance and Service Guide
Part number 601465-003
Third edition March 2013
Legal notices
© Copyright 2010, 2013 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are
set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed
as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
AMD is trademark of Advanced Micro Devices, Inc.
Intel® is a trademark of Intel Corporation in the U.S. and other countries.
Contents
Customer self repair ............................................................................................................................. 5
Parts only warranty service .......................................................................................................................... 5
Illustrated parts catalog ....................................................................................................................... 16
Mechanical components / 4 3.5” LFF HDD hot-plug model ........................................................................... 16
Mechanical components / 8 2.5” SFF HDD hot-plug model .......................................................................... 17
System components / 4 3.5” LFF HDD hot-plug model .................................................................................. 21
System components / 8 2.5” SFF HDD hot-plug model ................................................................................. 24
HP contact information .............................................................................................................................. 28
Before you contact HP ............................................................................................................................... 28
Removal and replacement procedures ................................................................................................... 29
Hardware configuration tools ..................................................................................................................... 29
Hardware configuration information ........................................................................................................... 29
Electrostatic discharge information ......................................................................................................... 29
Pre-installation procedure ...................................................................................................................... 30
Post-installation instructions.................................................................................................................... 30
Server warnings and cautions .................................................................................................................... 31
Symbols on equipment .............................................................................................................................. 31
Powering down the server .......................................................................................................................... 32
System cover ............................................................................................................................................ 33
Top cover ............................................................................................................................................ 33
Drives ...................................................................................................................................................... 34
Cable management.............................................................................................................................. 34
Cable connections ............................................................................................................................... 35
Drive bay configuration ........................................................................................................................ 36
Optical Media Device Bay .................................................................................................................... 39
Hard drives ......................................................................................................................................... 41
SAS/SATA HDD backplane .................................................................................................................. 48
Cable Routing ..................................................................................................................................... 51
System board configuration ....................................................................................................................... 55
Processor ............................................................................................................................................ 55
Memory .............................................................................................................................................. 63
PCI expansion card .............................................................................................................................. 66
System battery ..................................................................................................................................... 75
BBWC (Optional) ................................................................................................................................ 76
SD card reader module (Optional) ......................................................................................................... 78
Mgmt card (Optional)........................................................................................................................... 81
System board removal and replacement procedure ...................................................................................... 83
Power supply unit (PSU) ............................................................................................................................. 85
System fan ............................................................................................................................................... 89
Connectors, switches, and LEDs ........................................................................................................... 92
Connectors and components ...................................................................................................................... 92
Front panel components ........................................................................................................................ 92
Rear panel components ........................................................................................................................ 94
System board components .................................................................................................................... 95
Jumper ................................................................................................................................................ 96
LED indicators ........................................................................................................................................... 96
Contents
3
Front panel LED indicators .................................................................................................................... 97
Optical drive activity LED indicator ........................................................................................................ 98
Hard Drive LED indicators ..................................................................................................................... 99
Rear panel LED indicators ................................................................................................................... 100
System board LED indicator ................................................................................................................ 101
Diagnostic tools and setup utilities ...................................................................................................... 102
BIOS software ........................................................................................................................................ 102
BIOS Setup Utility ................................................................................................................................... 102
Accessing the BIOS Setup Utility ............................................................................................................... 102
Navigating through the Setup Utility..................................................................................................... 103
Setup Utility menu bar ........................................................................................................................ 103
BIOS update .......................................................................................................................................... 109
Power-On Self-Test (POST) ........................................................................................................................ 109
POST error indicators ......................................................................................................................... 110
POST related troubleshooting .............................................................................................................. 110
Physical and operating specifications .................................................................................................. 111
System unit ............................................................................................................................................. 111
Index .............................................................................................................................................. 115
Contents
4
Customer self repair
HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and
allow for greater flexibility in performing defective parts replacement. If during the diagnosis period
HP (or HP service providers or service partners) identifies that the repair can be accomplished by the
use of a CSR part, HP will ship that part directly to you for replacement. There are two categories of
CSR parts:
•
Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace
these parts, you will be charged for the travel and labor costs of this service.
•
Optional—Parts for which customer self repair is optional. These parts are also designed for
customer self repair. If, however, you require that HP replace them for you, there may or may not
be additional charges, depending on the type of warranty service designated for your product.
NOTE: Some HP parts are not designed for customer self repair. In order to satisfy the customer
warranty, HP requires that an authorized service provider replace the part. These parts are identified
as "No" in the Illustrated Parts Catalog.
Based on availability and where geography permits, CSR parts will be shipped for next business day
delivery. Same day or four-hour delivery may be offered at an additional charge where geography
permits. If assistance is required, you can call the HP Technical Support Center and a technician will
help you over the telephone. HP specifies in the materials shipped with a replacement CSR part
whether a defective part must be returned to HP. In cases where it is required to return the defective
part to HP, you must ship the defective part back to HP within a defined period of time, normally five
(5) business days. The defective part must be returned with the associated documentation in the
provided shipping material. Failure to return the defective part may result in HP billing you for the
replacement. With a customer self repair, HP will pay all shipping and part return costs and
determine the courier/carrier to be used.
For more information about HP's Customer Self Repair program, contact your local service provider.
For the North American program, refer to the HP website (http://www.hp.com/go/selfrepair).
Parts only warranty service
Your HP Limited Warranty may include a parts only warranty service. Under the terms of parts only
warranty service, HP will provide replacement parts free of charge.
For parts only warranty service, CSR part replacement is mandatory. If you request HP to replace
these parts, you will be charged for the travel and labor costs of this service.
Customer self repair 5
Réparation par le client (CSR)
Les produits HP comportent de nombreuses pièces CSR (Customer Self Repair = réparation par le
client) afin de minimiser les délais de réparation et faciliter le remplacement des pièces défectueuses.
Si pendant la période de diagnostic, HP (ou ses partenaires ou mainteneurs agréés) détermine que la
réparation peut être effectuée à l'aide d'une pièce CSR, HP vous l'envoie directement. Il existe deux
catégories de pièces CSR:
•
Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous
demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service
vous seront facturés.
•
Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont
également conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous
demandez à HP de remplacer ces pièces, l'intervention peut ou non vous être facturée, selon le
type de garantie applicable à votre produit.
REMARQUE: Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même
la réparation. Pour que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit
effectué par un Mainteneur Agréé. Ces pièces sont identifiées par la mention "Non" dans le
Catalogue illustré.
Les pièces CSR sont livrées le jour ouvré suivant, dans la limite des stocks disponibles et selon votre
situation géographique. Si votre situation géographique le permet et que vous demandez une
livraison le jour même ou dans les 4 heures, celle-ci vous sera facturée. Pour bénéficier d'une
assistance téléphonique, appelez le Centre d'assistance technique HP. Dans les documents envoyés
avec la pièce de rechange CSR, HP précise s'il est nécessaire de lui retourner la pièce défectueuse. Si
c'est le cas, vous devez le faire dans le délai indiqué, généralement cinq (5) jours ouvrés. La pièce et
sa documentation doivent être retournées dans l'emballage fourni. Si vous ne retournez pas la pièce
défectueuse, HP se réserve le droit de vous facturer les coûts de remplacement. Dans le cas d'une
pièce CSR, HP supporte l'ensemble des frais d'expédition et de retour, et détermine la société de
courses ou le transporteur à utiliser.
Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour
plus d'informations sur ce programme en Amérique du Nord, consultez le site Web HP
(http://www.hp.com/go/selfrepair).
Service de garantie "pièces seules"
Votre garantie limitée HP peut inclure un service de garantie "pièces seules". Dans ce cas, les pièces
de rechange fournies par HP ne sont pas facturées.
Dans le cadre de ce service, la réparation des pièces CSR par le client est obligatoire. Si vous
demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous
seront facturés.
Customer self repair 6
Riparazione da parte del cliente
Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti
difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati
direttamente dal cliente (CSR, Customer Self Repair). Se in fase di diagnostica HP (o un centro di
servizi o di assistenza HP) identifica il guasto come riparabile mediante un ricambio CSR, HP lo
spedirà direttamente al cliente per la sostituzione. Vi sono due categorie di parti CSR:
•
Obbligatorie—Parti che devono essere necessariamente riparate dal cliente. Se il cliente ne
affida la riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il
servizio.
•
Opzionali—Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque di
componenti progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP,
potrebbe dover sostenere spese addizionali a seconda del tipo di garanzia previsto per il
prodotto.
NOTA: alcuni componenti HP non sono progettati per la riparazione da parte del cliente. Per
rispettare la garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza
autorizzato. Tali parti sono identificate da un "No" nel Catalogo illustrato dei componenti.
In base alla disponibilità e alla località geografica, le parti CSR vengono spedite con consegna entro
il giorno lavorativo seguente. La consegna nel giorno stesso o entro quattro ore è offerta con un
supplemento di costo solo in alcune zone. In caso di necessità si può richiedere l'assistenza telefonica
di un addetto del centro di supporto tecnico HP. Nel materiale fornito con una parte di ricambio CSR,
HP specifica se il cliente deve restituire dei componenti. Qualora sia richiesta la resa ad HP del
componente difettoso, lo si deve spedire ad HP entro un determinato periodo di tempo, generalmente
cinque (5) giorni lavorativi. Il componente difettoso deve essere restituito con la documentazione
associata nell'imballo di spedizione fornito. La mancata restituzione del componente può comportare
la fatturazione del ricambio da parte di HP. Nel caso di riparazione da parte del cliente, HP sostiene
tutte le spese di spedizione e resa e sceglie il corriere/vettore da utilizzare.
Per ulteriori informazioni sul programma CSR di HP contattare il centro di assistenza di zona. Per il
programma in Nord America fare riferimento al sito Web HP (http://www.hp.com/go/selfrepair).
Servizio di garanzia per i soli componenti
La garanzia limitata HP può includere un servizio di garanzia per i soli componenti. Nei termini di
garanzia del servizio per i soli componenti, HP fornirà gratuitamente le parti di ricambio.
Per il servizio di garanzia per i soli componenti è obbligatoria la formula CSR che prevede la
riparazione da parte del cliente. Se il cliente invece richiede la sostituzione ad HP, dovrà sostenere le
spese di spedizione e di manodopera per il servizio.
Customer self repair 7
Customer self repair
HP Produkte enthalten viele CSR-Teile (Customer Self Repair), um Reparaturzeiten zu minimieren und
höhere Flexibilität beim Austausch defekter Bauteile zu ermöglichen. Wenn HP (oder ein HP
Servicepartner) bei der Diagnose feststellt, dass das Produkt mithilfe eines CSR-Teils repariert werden
kann, sendet Ihnen HP dieses Bauteil zum Austausch direkt zu. CSR-Teile werden in zwei Kategorien
unterteilt:
•
Zwingend—Teile, für die das Customer Self Repair-Verfahren zwingend vorgegeben ist. Wenn
Sie den Austausch dieser Teile von HP vornehmen lassen, werden Ihnen die Anfahrt- und
Arbeitskosten für diesen Service berechnet.
•
Optional—Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind auch
für Customer Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP
vornehmen lassen möchten, können bei diesem Service je nach den für Ihr Produkt vorgesehenen
Garantiebedingungen zusätzliche Kosten anfallen.
HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des
Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten
Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet.
CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag
geliefert. Für bestimmte Standorte ist eine Lieferung am selben Tag oder innerhalb von vier Stunden
gegen einen Aufpreis verfügbar. Wenn Sie Hilfe benötigen, können Sie das HP technische Support
Center anrufen und sich von einem Mitarbeiter per Telefon helfen lassen. Den Materialien, die mit
einem CSR-Ersatzteil geliefert werden, können Sie entnehmen, ob das defekte Teil an HP
zurückgeschickt werden muss. Wenn es erforderlich ist, das defekte Teil an HP zurückzuschicken,
müssen Sie dies innerhalb eines vorgegebenen Zeitraums tun, in der Regel innerhalb von fünf (5)
Geschäftstagen. Das defekte Teil muss mit der zugehörigen Dokumentation in der Verpackung
zurückgeschickt werden, die im Lieferumfang enthalten ist. Wenn Sie das defekte Teil nicht
zurückschicken, kann HP Ihnen das Ersatzteil in Rechnung stellen. Im Falle von Customer Self Repair
kommt HP für alle Kosten für die Lieferung und Rücksendung auf und bestimmt den Kurier/Frachtdienst.
Weitere Informationen über das HP Customer Self Repair Programm erhalten Sie von Ihrem
Servicepartner vor Ort. Informationen über das CSR-Programm in Nordamerika finden Sie auf der HP
Website unter (http://www.hp.com/go/selfrepair).
Parts-only warranty service (Garantieservice
ausschließlich für Teile)
Ihre HP Garantie umfasst möglicherweise einen Parts-only Warranty Service (Garantieservice
ausschließlich für Teile). Gemäß den Bestimmungen des Parts-only Warranty Service stellt HP
Ersatzteile kostenlos zur Verfügung.
Für den Parts-only Warranty Service ist das CSR-Verfahren zwingend vorgegeben. Wenn Sie den
Austausch dieser Teile von HP vornehmen lassen, werden Ihnen die Anfahrt- und Arbeitskosten für
diesen Service berechnet
Customer self repair 8
Reparaciones del propio cliente
Los productos de HP incluyen muchos componentes que el propio usuario puede reemplazar
(Customer Self Repair, CSR) para minimizar el tiempo de reparación y ofrecer una mayor flexibilidad
a la hora de realizar sustituciones de componentes defectuosos. Si, durante la fase de diagnóstico,
HP (o los proveedores o socios de servicio de HP) identifica que una reparación puede llevarse a
cabo mediante el uso de un componente CSR, HP le enviará dicho componente directamente para
que realice su sustitución. Los componentes CSR se clasifican en dos categorías:
•
Obligatorio—componentes para los que la reparación por parte del usuario es obligatoria. Si
solicita a HP que realice la sustitución de estos componentes, tendrá que hacerse cargo de los
gastos de desplazamiento y de mano de obra de dicho servicio.
•
Opcional—componentes para los que la reparación por parte del usuario es opcional. Estos
componentes también están diseñados para que puedan ser reparados por el usuario. Sin
embargo, si precisa que HP realice su sustitución, puede o no conllevar costes adicionales,
dependiendo del tipo de servicio de garantía correspondiente al producto.
NOTA: Algunos componentes no están diseñados para que puedan ser reparados por el usuario.
Para que el usuario haga valer su garantía, HP pone como condición que un proveedor de servicios
autorizado realice la sustitución de estos componentes. Dichos componentes se identifican con la
palabra "No" en el catálogo ilustrado de componentes.
Según la disponibilidad y la situación geográfica, los componentes CSR se enviarán para que
lleguen a su destino al siguiente día laborable. Si la situación geográfica lo permite, se puede
solicitar la entrega en el mismo día o en cuatro horas con un coste adicional. Si precisa asistencia
técnica, puede llamar al Centro de asistencia técnica de HP y recibirá ayuda telefónica por parte de
un técnico. Con el envío de materiales para la sustitución de componentes CSR, HP especificará si los
componentes defectuosos deberán devolverse a HP. En aquellos casos en los que sea necesario
devolver algún componente a HP, deberá hacerlo en el periodo de tiempo especificado,
normalmente cinco días laborables. Los componentes defectuosos deberán devolverse con toda la
documentación relacionada y con el embalaje de envío. Si no enviara el componente defectuoso
requerido, HP podrá cobrarle por el de sustitución. En el caso de todas sustituciones que lleve a cabo
el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes y escogerá la
empresa de transporte que se utilice para dicho servicio.
Para obtener más información acerca del programa de Reparaciones del propio cliente de HP,
póngase en contacto con su proveedor de servicios local. Si está interesado en el programa para
Norteamérica, visite la página web de HP siguiente (http://www.hp.com/go/selfrepair).
Servicio de garantía exclusivo de componentes
La garantía limitada de HP puede que incluya un servicio de garantía exclusivo de componentes.
Según las condiciones de este servicio exclusivo de componentes, HP le facilitará los componentes de
repuesto sin cargo adicional alguno.
Para este servicio de garantía exclusivo de componentes, es obligatoria la sustitución de
componentes por parte del usuario (CSR). Si solicita a HP que realice la sustitución de estos
componentes, tendrá que hacerse cargo de los gastos de desplazamiento y de mano de obra de
dicho servicio.
Customer self repair 9
Customer self repair
Veel onderdelen in HP producten zijn door de klant zelf te repareren, waardoor de reparatieduur tot
een minimum beperkt kan blijven en de flexibiliteit in het vervangen van defecte onderdelen groter is.
Deze onderdelen worden CSR-onderdelen (Customer Self Repair) genoemd. Als HP (of een HP
Service Partner) bij de diagnose vaststelt dat de reparatie kan worden uitgevoerd met een CSRonderdeel, verzendt HP dat onderdeel rechtstreeks naar u, zodat u het defecte onderdeel daarmee
kunt vervangen. Er zijn twee categorieën CSR-onderdelen:
•
Verplicht—Onderdelen waarvoor reparatie door de klant verplicht is. Als u HP verzoekt deze
onderdelen voor u te vervangen, worden u voor deze service reiskosten en arbeidsloon in
rekening gebracht.
•
Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen
zijn ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te
vervangen, kunnen daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type
garantieservice voor het product.
OPMERKING: Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In
verband met de garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner
worden vervangen. Deze onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt
met "Nee".
Afhankelijk van de leverbaarheid en de locatie worden CSR-onderdelen verzonden voor levering op
de eerstvolgende werkdag. Levering op dezelfde dag of binnen vier uur kan tegen meerkosten
worden aangeboden, indien dit mogelijk is gezien de locatie. Indien assistentie gewenst is, belt u een
HP Service Partner om via de telefoon technische ondersteuning te ontvangen. HP vermeldt in de
documentatie bij het vervangende CSR-onderdeel of het defecte onderdeel aan HP moet worden
geretourneerd. Als het defecte onderdeel aan HP moet worden teruggezonden, moet u het defecte
onderdeel binnen een bepaalde periode, gewoonlijk vijf (5) werkdagen, retourneren aan HP. Het
defecte onderdeel moet met de bijbehorende documentatie worden geretourneerd in het
meegeleverde verpakkingsmateriaal. Als u het defecte onderdeel niet terugzendt, kan HP u voor het
vervangende onderdeel kosten in rekening brengen. Bij reparatie door de klant betaalt HP alle
verzendkosten voor het vervangende en geretourneerde onderdeel en kiest HP zelf welke
koerier/transportonderneming hiervoor wordt gebruikt.
Neem contact op met een Service Partner voor meer informatie over het Customer Self Repair
programma van HP. Informatie over Service Partners vindt u op de HP website
(http://www.hp.com/go/selfrepair).
Garantieservice "Parts Only"
Het is mogelijk dat de HP garantie alleen de garantieservice "Parts Only" omvat. Volgens de
bepalingen van de Parts Only garantieservice zal HP kosteloos vervangende onderdelen ter
beschikking stellen.
Voor de Parts Only garantieservice is vervanging door CSR-onderdelen verplicht. Als u HP verzoekt
deze onderdelen voor u te vervangen, worden u voor deze service reiskosten en arbeidsloon in
rekening gebracht.
Customer self repair 10
Reparo feito pelo cliente
Os produtos da HP são projetados com muitas peças para reparo feito pelo cliente (CSR) de modo a
minimizar o tempo de reparo e permitir maior flexibilidade na substituição de peças com defeito. Se,
durante o período de diagnóstico, a HP (ou fornecedores/parceiros de serviço da HP) concluir que o
reparo pode ser efetuado pelo uso de uma peça CSR, a peça de reposição será enviada diretamente
ao cliente. Existem duas categorias de peças CSR:
•
Obrigatória—Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua
essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
•
Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são
projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode
haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia
destinado ao produto.
OBSERVAÇÃO: Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim
de cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça. Essas
peças estão identificadas com a marca "No" (Não), no catálogo de peças ilustrado.
Conforme a disponibilidade e o local geográfico, as peças CSR serão enviadas no primeiro dia útil
após o pedido. Onde as condições geográficas permitirem, a entrega no mesmo dia ou em quatro
horas pode ser feita mediante uma taxa adicional. Se precisar de auxílio, entre em contato com o
Centro de suporte técnico da HP para que um técnico o ajude por telefone. A HP especifica nos
materiais fornecidos com a peça CSR de reposição se a peça com defeito deve ser devolvida à HP.
Nos casos em que isso for necessário, é preciso enviar a peça com defeito à HP dentro do período
determinado, normalmente cinco (5) dias úteis. A peça com defeito deve ser enviada com a
documentação correspondente no material de transporte fornecido. Caso não o faça, a HP poderá
cobrar a reposição. Para as peças de reparo feito pelo cliente, a HP paga todas as despesas de
transporte e de devolução da peça e determina a transportadora/serviço postal a ser utilizado.
Para obter mais informações sobre o programa de reparo feito pelo cliente da HP, entre em contato
com o fornecedor de serviços local. Para o programa norte-americano, visite o site da HP
(http://www.hp.com/go/selfrepair).
Serviço de garantia apenas para peças
A garantia limitada da HP pode incluir um serviço de garantia apenas para peças. Segundo os
termos do serviço de garantia apenas para peças, a HP fornece as peças de reposição sem cobrar
nenhuma taxa.
No caso desse serviço, a substituição de peças CSR é obrigatória. Se desejar que a HP substitua
essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
Customer self repair 11
Customer self repair 12
Customer self repair 13
Customer self repair 14
Customer self repair 15
Illustrated parts catalog
Mechanical components / 4 3.5” LFF HDD hotplug model
Table 1 Mechanical Components Spare Parts List / 4 3.5” LFF HDD Hot-plug Model
Item
Description
Spare Part
Number
1
PCI cage
N/A
2
Air baffle
603889-001
Mandatory1
3
Power supply cage
532473-001
Mandatory1
4
Rail kit
573091-001
Mandatory1
5
Hard drive cage
532114-001
Optional2
6
Optical drive blank
532475-001
Mandatory1
7
Hard drive blank
389015-001
Mandatory1
8
Top cover
507262-001
Mandatory1
Customer Self
Repair
Illustrated parts catalog
16
Mechanical components / 8 2.5” SFF HDD hotplug model
Table 2 Mechanical Components Spare Parts List / 8 2.5” SFF HDD Hot-plug Model
Item
Description
Spare Part
Number
Customer Self
Repair
1
PCI cage
N/A
2
Air baffle
603889-001
Mandatory1
3
Power supply cage
532473-001
Mandatory1
4
Rail kit
573091-001
Mandatory1
5
Hard drive cage
532480-001
Optional2
6
Optical drive blank
532475-001
Mandatory1
7
Hard drive blank
392613-001
Mandatory1
8
Top cover
507262-001
Mandatory1
Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these
parts, you will be charged for the travel and labor costs of this service.
1
Optional—Parts for which customer self repair is optional. These parts are also designed for
customer self repair. If, however, you require that HP replace them for you, there may or may not be
additional charges, depending on the type of warranty service designated for your product.
2
No—Some HP parts are not designed for customer self repair. In order to satisfy the customer
warranty, HP requires that an authorized service provider replace the part. These parts are identified
as "No" in the Illustrated Parts Catalog.
3
Illustrated parts catalog
17
Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous
demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous
seront facturés.
1
Optional: Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont
également conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous
demandez à HP de remplacer ces pièces, l'intervention peut ou non vous être facturée, selon le type
de garantie applicable à votre produit.
2
No: Non—Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la
réparation. Pour que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit
effectué par un Mainteneur Agréé. Ces pièces sont identifiées par la mention “Non” dans le
Catalogue illustré.
3
Mandatory: Obbligatorie—Parti che devono essere necessariamente riparate dal cliente. Se il cliente
ne affida la riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il
servizio.
1
Optional: Opzionali—Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque
di componenti progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP,
potrebbe dover sostenere spese addizionali a seconda del tipo di garanzia previsto per il prodotto.
2
No: Non CSR—Alcuni componenti HP non sono progettati per la riparazione da parte del cliente.
Per rispettare la garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza
autorizzato. Tali parti sono identificate da un “No” nel Catalogo illustrato dei componenti.
3
Mandatory: Zwingend—Teile, die im Rahmen des Customer Self Repair Programms ersetzt werden
müssen. Wenn Sie diese Teile von HP ersetzen lassen, werden Ihnen die Versand- und Arbeitskosten
für diesen Service berechnet.
1
Optional: Optional—Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind
auch für Customer Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP
vornehmen lassen möchten, können bei diesem Service je nach den für Ihr Produkt vorgesehenen
Garantiebedingungen zusätzliche Kosten anfallen.
2
No: Kein—Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des
Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten
Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet.
3
Mandatory: Obligatorio—componentes para los que la reparación por parte del usuario es
obligatoria. Si solicita a HP que realice la sustitución de estos componentes, tendrá que hacerse
cargo de los gastos de desplazamiento y de mano de obra de dicho servicio.
1
Optional: Opcional—componentes para los que la reparación por parte del usuario es opcional.
Estos componentes también están diseñados para que puedan ser reparados por el usuario. Sin
embargo, si precisa que HP realice su sustitución, puede o no conllevar costes adicionales,
dependiendo del tipo de servicio de garantía correspondiente al producto.
2
No: No—Algunos componentes no están diseñados para que puedan ser reparados por el usuario.
Para que el usuario haga valer su garantía, HP pone como condición que un proveedor de servicios
3
Illustrated parts catalog
18
autorizado realice la sustitución de estos componentes. Dichos componentes se identifican con la
palabra “No” en el catálogo ilustrado de componentes.
Mandatory: Verplicht—Onderdelen waarvoor Customer Self Repair verplicht is. Als u HP verzoekt
deze onderdelen te vervangen, komen de reiskosten en het arbeidsloon voor uw rekening.
1
Optional: Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze
onderdelen zijn ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen
voor u te vervangen, kunnen daarvoor extra kosten in rekening worden gebracht, afhankelijk van het
type garantieservice voor het product.
2
No: Nee—Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband
met de garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden
vervangen. Deze onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met
"Nee".
3
Mandatory: Obrigatória—Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP
substitua essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
1
Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são
projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode
haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado
ao produto.
2
No: Nenhuma—Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de
cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças
estão identificadas com a marca “No” (Não), no catálogo de peças ilustrado.
3
Illustrated parts catalog
19
Illustrated parts catalog
20
System components / 4 3.5” LFF HDD hot-plug
model
Table 3 System Components Spare Parts List / 4 3.5” LFF HDD Hot-plug Model
Item
Description
Spare Part
Number
Customer Self
Repair
1
PCIe x16 riser card
603891-001
Optional2
2
PCIe x8 riser card
603890-001
Optional2
3
Power supplies
a) Hot-plug power supply (750 W)
511778-001
Mandatory1
b) Non-hot-plug power supply (500 W)
506247-001
Mandatory1
4
System board
603887-001
Optional2
5
Memory modules
a) DIMM 2GB PC3 10600R 128Mx8
595094-001
Mandatory1
b) DIMM 4GB PC3 10600R 256Mx4
595095-001
Mandatory1
c) DIMM 4GB PC3 10600R 512Mx4
595096-001
Mandatory1
d) DIMM 8GB PC3 10600R 512Mx4
595097-001
Mandatory1
e) DIMM 16GB PC3 8500R 512Mx4
595098-001
Mandatory1
f) DIMM 4GB PC3L 8500R 256Mx8
595099-001
Mandatory1
g) DIMM 8GB PC3L 8500R 512Mx4
595100-001
Mandatory1
h) DIMM 2GB PC3 10600E 128Mx8
595101-001
Mandatory1
Illustrated parts catalog
21
Table 3 System Components Spare Parts List / 4 3.5” LFF HDD Hot-plug Model
Item
Description
Spare Part
Number
Customer Self
Repair
i) DIMM 4GB PC3 10600E 256Mx8
595102-001
Mandatory1
a) AMD processor 6128HE, 8c, 2.0 GHz, 55W
583751-001
Optional2
b) AMD processor 6128, 8c, 2.0 GHz, 75W
598732-001
Optional2
c) AMD processor 6132HE, 8c, 2.2 GHz, 65W
633546-001
Optional2
d) AMD processor 6136, 8c, 2.4 GHz, 75W
583753-001
Optional2
e) AMD processor 6140, 8c, 2.6 GHz, 80W
633544-001
Optional2
f) AMD processor 6172, 12c, 2.1 GHz, 75W
583755-001
Optional2
g) AMD processor 6174, 12c, 2.2 GHz, 80W
598729-001
Optional2
h) AMD processor 6176, 12c, 2.3 GHz, 80W
633722-001
Optional2
i) AMD processor 6134, 8c, 2.3 GHz, 75W
583752-001
Optional2
j) AMD processor 6164, 12c, 1.7 GHz, 75W
583754-001
Optional2
k) AMD processor 6164HE, 12c, 1.7 GHz, 65W
598730-001
Optional2
7
Processor 1 heat sink
603888-001
Optional2
8
Processor 2 heat sink
602500-001
Optional2
9
9.5mm (0.37 in.) DVD ROM optical drive (optional)
481430-001
Mandatory1
10
Hard Drives with carriers
a) LFF 160-GB, SATA, 7,200-rpm
399967-001
Mandatory1
b) LFF 250-GB, SATA, 7,200-rpm
399968-001
Mandatory1
c) LFF 500-GB, SATA, 7,200-rpm
399969-001
Mandatory1
d) LFF 750-GB, SATA, 7,200-rpm
549320-001
Mandatory1
e) LFF 1-TB, SATA, 7,200-rpm
545273-001
Mandatory1
f) LFF 2-TB, SATA, 7,200-rpm
508040-001
Mandatory1
g) LFF 36-GB, SAS, 10,000-rpm
376593-001
Mandatory1
h) LFF 72-GB, SAS, 10,000-rpm
376594-001
Mandatory1
i) LFF 146-GB, SAS, 10,000-rpm
376595-001
Mandatory1
j) LFF 72-GB, SAS, dual-port, 15,000-rpm
389343-001
Mandatory1
k) LFF 146-GB, SAS, dual-port, 15,000-rpm
389344-001
Mandatory1
l) LFF 300-GB, SAS, dual-port, 15,000-rpm
432146-001
Mandatory1
m) LFF 450-GB, SAS, dual-port, 15,000-rpm
454274-001
Mandatory1
n) LFF 600-GB, SAS, dual-port, 15,000-rpm
586877-001
Mandatory1
o) LFF 300GB, SAS, 6G/s
586875-001
Mandatory1
6
Processor Options
Illustrated parts catalog
22
Table 3 System Components Spare Parts List / 4 3.5” LFF HDD Hot-plug Model
Item
Description
Spare Part
Number
Customer Self
Repair
p) LFF 600GB, SAS, 6G/s
586877-001
Mandatory1
q) LFF 1-TB, SAS, 6G/s
601884-001
Mandatory1
r) LFF 2-TB, SAS, 6G/s
601883-001
Mandatory1
11
Backplane four LFF bays SAS/SATA hard drive
570079-001
Optional2
12
System fans
519711-001
Mandatory1
*
Control Panel Assembly w/cables
603892-001
Optional2
*
Voltage Regulator Module
536406-001
Optional2
*
Cable, I2C
536399-001
Optional2
*
Cable, USB
538820-001
Optional2
*
Cable, SAS
498425-001
Optional2
*
Cable, BBWC
488137-001
Optional2
*
Smart Array Controller Board
462919-001
Optional2
*
Cache Module 256GB
462974-001
Optional2
*
Battery Module, BBWC
462976-001
Optional2
*
SD Card Reader Board
608253-001
Optional2
*
Management Port Board
516806-001
Optional2
Illustrated parts catalog
23
System components / 8 2.5” SFF HDD hot-plug
model
Table 4 System Components Spare Parts List / 8 2.5” SFF HDD Hot-plug Model
Item
Description
Spare Part
Number
Customer Self
Repair
1
PCIe x16 riser card
603891-001
Optional2
2
PCIe x8 riser card
603890-001
Optional2
3
Power supplies
a) Hot-plug power supply (750 W)
511778-001
Mandatory1
b) Non-hot-plug power supply (500 W)
506247-001
Mandatory1
4
Voltage Regulator Module
536406-001
Optional2
5
System board
603887-001
Optional2
6
Memory modules
a) DIMM 2GB PC3 10600R 128Mx8
595094-001
Mandatory1
b) DIMM 4GB PC3 10600R 256Mx4
595095-001
Mandatory1
c) DIMM 4GB PC3 10600R 512Mx4
595096-001
Mandatory1
d) DIMM 8GB PC3 10600R 512Mx4
595097-001
Mandatory1
e) DIMM 16GB PC3 8500R 512Mx4
595098-001
Mandatory1
f) DIMM 4GB PC3L 8500R 256Mx8
595099-001
Mandatory1
Illustrated parts catalog
24
Table 4 System Components Spare Parts List / 8 2.5” SFF HDD Hot-plug Model
Item
Description
Spare Part
Number
Customer Self
Repair
g) DIMM 8GB PC3L 8500R 512Mx4
595100-001
Mandatory1
h) DIMM 2GB PC3 10600E 128Mx8
595101-001
Mandatory1
i) DIMM 4GB PC3 10600E 256Mx8
595102-001
Mandatory1
a) AMD processor 6128HE, 8c, 2.0 GHz, 55W
583751-001
Optional2
b) AMD processor 6128, 8c, 2.0 GHz, 75W
598732-001
Optional2
c) AMD processor 6132HE, 8c, 2.2 GHz, 65W
633546-001
Optional2
d) AMD processor 6136, 8c, 2.4 GHz, 75W
583753-001
Optional2
e) AMD processor 6140, 8c, 2.6 GHz, 80W
633544-001
Optional2
f) AMD processor 6172, 12c, 2.1 GHz, 75W
583755-001
Optional2
g) AMD processor 6174, 12c, 2.2 GHz, 80W
598729-001
Optional2
h) AMD processor 6176, 12c, 2.3 GHz, 80W
633722-001
Optional2
i) AMD processor 6134, 8c, 2.3 GHz, 75W
583752-001
Optional2
j) AMD processor 6164, 12c, 1.7 GHz, 75W
583754-001
Optional2
k) AMD processor 6164HE, 12c, 1.7 GHz, 65W
598730-001
Optional2
8
Processor 1 heat sink
603888-001
Optional2
9
Processor 2 heat sink
602500-001
Optional2
10
9.5mm (0.37 in.) DVD ROM optical drive
481430-001
Mandatory1
11
Hard Drives with carriers
a) SFF 36-GB, SAS, 10,000-rpm, hot-plug, 3G
376596-001
Mandatory1
b) SFF 36-GB, SAS, 15,000-rpm, hot-plug, dual-port, 3G
418397-001
Mandatory1
c) SFF 36-GB, SAS, 15,000-rpm, hot-plug, 3G
432322-001
Mandatory1
d) SFF 72-GB, SAS, 10,000-rpm, hot-plug, 3G
434916-001
Mandatory1
e) SFF 72-GB, SAS, 15,000-rpm, hot-plug, dual-port
418398-001
Mandatory1
f) SFF 72-GB, SAS, 10,000-rpm, hot-plug, dual-port, 3G
389346-001
Mandatory1
g) SFF 72-GB, SAS, 15,000-rpm, hot-plug, 3G
432321-001
Mandatory1
h) SFF 146-GB, SAS, 10,000-rpm, hot-plug, dual-port
418399-001
Mandatory1
i) SFF 146-GB, SAS, 10,000-rpm, hot-plug, 3G
432320-001
Mandatory1
j) SFF 146-GB, SAS, 10,000-rpm, hot-plug, dual-port, 6G
507283-001
Mandatory1
k) SFF 300-GB, SAS, 10,000-rpm, hot-plug, dual-port
493083-001
Mandatory1
l) SFF 300-GB, SAS, 10,000-rpm, hot-plug, dual-port, 6G
507284-001
Mandatory1
m) SFF 72GB, SAS, 6GB/s, 15K
586871-001
Mandatory1
7
Processor Options
Illustrated parts catalog
25
Table 4 System Components Spare Parts List / 8 2.5” SFF HDD Hot-plug Model
Item
Description
Spare Part
Number
Customer Self
Repair
n) SFF 146GB, SAS, 6GB/s, 10K
507129-002
Mandatory1
o) SFF 146GB, SAS, 6GB/s, 15K
507129-010
Mandatory1
p) SFF 300GB, SAS, 6GB/s, 10K
507129-004
Mandatory1
q) SFF 450GB, SAS, 6GB/s, 10K
507129-012
Mandatory1
r) SFF 500GB, SAS, 6GB/s, 7.2K
507129-006
Mandatory1
s) SFF 600GB, SAS, 6GB/s, 10K
507129-014
Mandatory1
t) SFF 36GB,SSD, SATA
461332-001
Mandatory1
u) SFF 120GB, SSD, SATA
539557-008
Mandatory1
v) SFF 64GB, SSD, SATA
461333-001
Mandatory1
w) SFF 120GB SATA SSD
539557-010
Mandatory1
12
Backplane eight SFF bays SAS/SATA hard drive
532481-001
Optional2
13
System fans
519711-001
Mandatory1
*
Control Panel Assembly w/cables
603892-001
Optional2
NOTE: Items marked with * are not included in the system component figures. They are included in
the table for providing the spare part numbers and customer self repair information.
Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these
parts, you will be charged for the travel and labor costs of this service.
1
Optional—Parts for which customer self repair is optional. These parts are also designed for
customer self repair. If, however, you require that HP replace them for you, there may or may not be
additional charges, depending on the type of warranty service designated for your product.
2
No—Some HP parts are not designed for customer self repair. In order to satisfy the customer
warranty, HP requires that an authorized service provider replace the part. These parts are identified
as "No" in the Illustrated Parts Catalog.
3
Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous
demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous
seront facturés.
1
Optional: Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont
également conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous
demandez à HP de remplacer ces pièces, l'intervention peut ou non vous être facturée, selon le type
de garantie applicable à votre produit.
2
No: Non—Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la
réparation. Pour que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit
effectué par un Mainteneur Agréé. Ces pièces sont identifiées par la mention “Non” dans le
Catalogue illustré.
3
Illustrated parts catalog
26
Mandatory: Obbligatorie—Parti che devono essere necessariamente riparate dal cliente. Se il cliente
ne affida la riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il
servizio.
1
Optional: Opzionali—Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque
di componenti progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP,
potrebbe dover sostenere spese addizionali a seconda del tipo di garanzia previsto per il prodotto.
2
No: Non CSR—Alcuni componenti HP non sono progettati per la riparazione da parte del cliente.
Per rispettare la garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza
autorizzato. Tali parti sono identificate da un “No” nel Catalogo illustrato dei componenti.
3
Mandatory: Zwingend—Teile, die im Rahmen des Customer Self Repair Programms ersetzt werden
müssen. Wenn Sie diese Teile von HP ersetzen lassen, werden Ihnen die Versand-und Arbeitskosten
für diesen Service berechnet.
1
Optional: Optional—Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind
auch für Customer Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP
vornehmen lassen möchten, können bei diesem Service je nach den für Ihr Produkt vorgesehenen
Garantiebedingungen zusätzliche Kosten anfallen.
2
No: Kein—Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des
Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten
Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet.
3
Mandatory: Obligatorio—componentes para los que la reparación por parte del usuario es
obligatoria. Si solicita a HP que realice la sustitución de estos componentes, tendrá que hacerse
cargo de los gastos de desplazamiento y de mano de obra de dicho servicio.
1
Optional: Opcional—componentes para los que la reparación por parte del usuario es opcional.
Estos componentes también están diseñados para que puedan ser reparados por el usuario. Sin
embargo, si precisa que HP realice su sustitución, puede o no conllevar costes adicionales,
dependiendo del tipo de servicio de garantía correspondiente al producto.
2
No: No—Algunos componentes no están diseñados para que puedan ser reparados por el usuario.
Para que el usuario haga valer su garantía, HP pone como condición que un proveedor de servicios
autorizado realice la sustitución de estos componentes. Dichos componentes se identifican con la
palabra “No” en el catálogo ilustrado de componentes.
3
Mandatory: Verplicht—Onderdelen waarvoor Customer Self Repair verplicht is. Als u HP verzoekt
deze onderdelen te vervangen, komen de reiskosten en het arbeidsloon voor uw rekening.
1
Optional: Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze
onderdelen zijn ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen
voor u te vervangen, kunnen daarvoor extra kosten in rekening worden gebracht, afhankelijk van het
type garantieservice voor het product.
2
No: Nee—Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband
met de garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden
vervangen. Deze onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met
"Nee".
3
Illustrated parts catalog
27
Mandatory: Obrigatória—Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP
substitua essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
1
Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são
projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode
haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado
ao produto.
2
No: Nenhuma—Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de
cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças
estão identificadas com a marca “No” (Não), no catálogo de peças ilustrado.
3
HP contact information
For the name of the nearest HP authorized reseller:
•
•
•
In the United States, call 1-800-345-1518.
In Canada, call 1-800-263-5868.
In other locations, refer to the HP website at http://www.hp.com/.
For HP technical support:
•
In North America:
○ Call 1-800-HP-INVENT (1-800-474-6836). This service is available 24 hours a day, 7 days
a week. For continuous quality improvement, calls may be recorded or monitored.
○ If you have purchased a Care Pack (service upgrade), call 1-800-633-3600. For more
information about Care Packs, refer to the HP website at http://www.hp.com/.
•
Outside North America, call the nearest HP Technical Support Phone Center. For telephone
numbers for worldwide Technical Support Centers, refer to the HP website at
http://www.hp.com/.
Before you contact HP
Be sure to have the following information available before you call HP:
•
•
•
•
•
•
•
Technical support registration number (if applicable)
Product serial number
Product model name and number
Applicable error messages
Add-on boards or hardware model number and serial number
Third-party hardware or software model number
Operating system type and revision level
Illustrated parts catalog
28
Removal and replacement procedures
This chapter provides subassembly/module-level removal and replacement procedures for the HP
ProLiant DL165 G7 server.
Review the specifications of a new component before installing it to make sure it is compatible with
the server. When you integrate new components into the system, record its model and serial number,
and any other pertinent information for future reference. After completing any removal or replacement
procedure, run the diagnostics program to verify that all components operate properly.
NOTE: The figures used in this chapter to illustrate procedural steps are labeled numerically (i.e., 1,
2…). When these figures are used in substep items, the alphabetically labeled instructions
correspond to the numbered labels on the related figure (i.e., label 1 corresponds to step a, label 2
corresponds to step b, etc.). The procedures described in this section assume that the server is out of
the rack and is positioned on a flat, stable surface.
Hardware configuration tools
You will need the following tool:
T-10/T-15 wrench
The following references and software tools will assist with the hardware configuration:
•
•
•
HP ProLiant DL165 G7 Server Easy Set-up CD
IPMI Event Log
Diagnostics Software
Hardware configuration information
Electrostatic discharge information
An electrostatic discharge (ESD) can damage static-sensitive devices or micro circuitry. Proper
packaging and grounding techniques are necessary precautions to prevent damage. To prevent
electrostatic damage, observe the following precautions:
•
•
•
Transport products in static-safe containers such as conductive tubes, bags, or boxes.
•
Keep work area free of nonconductive materials, such as ordinary plastic assembly aids and
foam packing.
•
Make sure that you are always properly grounded (earthed) when touching a static-sensitive
component or assembly.
•
•
•
Avoid touching pins, leads, or circuitry.
Keep electrostatic-sensitive parts in their containers until they arrive at static-free stations.
Cover workstations with approved static-dissipating material. Use a wrist strap connected to the
work surface, and properly grounded (earthed) tools and equipment.
Always place drives with the Printed Circuit Board (PCB) assembly-side down.
Use conductive field service tools.
Removal and replacement procedures
29
Pre-installation procedure
Perform the steps below before you open the server or before you remove or replace any component.
WARNING: Failure to properly turn off the server before you open the server or before your start
installing and removing components may cause serious damage as well as bodily harm.
1.
Turn off the server and all the peripherals connected to it.
2.
Unplug all cables from the power outlet(s) to avoid exposure to high energy levels that may
cause burns when parts are short-circuited by metal objects such as tools or jewelry.
If necessary, label each one to expedite reassembly.
3.
Disconnect telecommunication cables to avoid exposure to shock hazard from ringing voltages.
4.
If server is installed in a rack, remove server and place it on a flat surface.
5.
Remove the top cover according to the instructions described in the “System cover” section in this
chapter.
6.
Follow the ESD precautions listed previously in this chapter when handling a server component.
IMPORTANT: To streamline the configuration process, read through the entire installation and
removal procedures first and make sure you understand them before you begin.
Post-installation instructions
Observe the following items after installing or removing a server component:
1.
Be sure all components are installed according to the described step-by-step instructions.
2.
Reinstall the rear cage, air baffle, peripherals, and system cables that you have removed.
3.
Reinstall the top cover.
4.
Reinstall server into rack.
5.
Connect all external cables and the AC power cord(s) to the system.
6.
Press the power button on the front panel to turn on the server.
Removal and replacement procedures
30
Server warnings and cautions
Before installing a server, be sure that you understand the following warnings and cautions.
WARNING: To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed against it.
Pay particular attention to the plug, electrical outlet, and the point where the cord extends from
the server.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal
system components to cool before touching them.
CAUTION: Do not operate the server for long periods with the system cover open or removed.
Operating the server in this manner results in improper airflow and improper cooling that can lead
to thermal damage.
Symbols on equipment
The following symbols may be placed on equipment to indicate the presence of potentially hazardous
conditions.
This symbol indicates the presence of hazardous energy circuits or electric shock
hazards. Refer all servicing to qualified personnel.
WARNING: To reduce the risk of injury from electric shock hazards, do not open this
enclosure. Refer all maintenance, upgrades, and servicing to qualified personnel.
This symbol indicates the presence of electric shock hazards. The area contains no
user or field serviceable parts. Do not open for any reason.
WARNING: To reduce the risk of injury from electric shock hazards, do not open this
enclosure.
This symbol on an RJ-45 receptacle indicates a network interface connection.
WARNING: To reduce the risk of electric shock, fire, or damage to the equipment, do
not plug telephone or telecommunications connectors into this receptacle.
This symbol indicates the presence of a hot surface or hot component. If this surface is
contacted, the potential for injury exists.
WARNING: To reduce the risk of injury from a hot component, allow the surface to
cool before touching.
Removal and replacement procedures
31
Weight in kg.
Weight in lb.
This symbol indicates that the component exceeds the recommended weight for one
individual to handle safely.
WARNING: To reduce the risk of personal injury or damage to the equipment,
observe local occupational health and safety requirements and guidelines for manual
material handling.
These symbols, on power supplies or systems, indicate that the equipment is supplied
by multiple sources of power.
WARNING: To reduce the risk of injury from electric shock, remove all power cords to
completely disconnect power from the system.
Powering down the server
The server does not completely power down when the power button on the front panel is pressed. The
button toggles between On and Standby. The standby position removes power from most electronics
and the drives, but some internal circuitry remains active. To completely remove all power from the
system, disconnect all power cords from the server.
To power down the server:
1.
Shut down the server as directed by the operating system documentation.
2.
Press the power button to toggle to Standby.
This places the server in standby mode changing the power LED indicator to amber. In this
mode, the main power supply output is disabled. Standby does not completely disable or
remove power from the system.
3.
Disconnect the AC power cord(s) from the power outlet(s) and then from the server.
4.
Be sure that the power LED indicator is turned off and that the fan noise has stopped.
5.
Disconnect all peripheral devices from the server.
Removal and replacement procedures
32
System cover
You need to remove the top cover before you can remove or replace a server component. The top
cover needs to be removed to service the SAS/SATA backplane.
Top cover
To remove the top cover:
1.
Loosen the screw on the top cover with a T-10 wrench.
2.
Press the latch on the top cover.
3.
Slide the cover toward the rear of the server and then lift the top cover to remove it from the
chassis.
Figure 1 Removing the Top Cover
To reinstall the top cover:
1.
Align the top cover to the chassis and then slide it towards the front panel to position it into
place.
2.
Once the cover is attached to the chassis, tighten the screw on the top cover with a T-10 wrench.
Removal and replacement procedures
33
Figure 2 Reinstalling the Top Cover
Drives
The server supports 5 to 9 drive bays --- 4 drive bays for 3.5 in. LFF hard disk drives and 1 drive bay
for an optical disc drive, or 8 drive bays for 2.5 in. SFF hard disk drives and 1 drive bay for an
optical disc drive.
Cable management
Always follow good cable management practices when working inside the computer.
•
•
Keep cables away from major heat sources like the heat sink.
•
•
Keep cables clear of sliding or moveable parts to prevent cutting or crimping.
•
•
•
•
•
Some flat ribbon cables come pre-folded. Never change the folds on these cables.
Do not jam cables on top of expansion cards or memory modules. Printed circuit cards are not
designed to withstand excessive pressure.
When folding a flat ribbon cable, never fold to a sharp crease. Sharp creases may damage the
wires.
Do not sharply bend any cable. A sharp bend can break the internal wires.
Never bend a SATA data cable tighter than a 30 mm (1.18 in.) radius.
Never crease a SATA data cable.
Do not rely on components like the drive cage, power supply, or system cover to push cables
down into the chassis.
The next steps illustrate the removal of power cable from connector J52, 53 and 54 on system board.
1.
Squeeze on the top of the retaining latch attached to the cable end of the connector.
2.
Grasp the cable end of the connector and pull it straight up.
CAUTION: Always pull the connector—NEVER pull on the cable. Pulling on the cable could damage
the cable and result in a failed power supply.
Removal and replacement procedures
34
Figure 3 Unplugging Power Cable
Cable connections
The following tables provide information about switching power supply cable connector labels.
Table 5 Cable Connections from the 500 W Non-hot-plug Power Supply
Cable
To
Cable Designator
Switching power supply
System board 24-pin power connector
P1
Switching power supply
System board 8-pin power connector
P11
Switching power supply
System board 4-pin power connector
P2
Switching power supply
System board power backplane connector
P10
Switching power supply
4 LFF HDD hot-plug Backplane power
connector
P4
Table 6 Cable Connections from the 750 W Hot-plug Power Supply
Cable
To
Cable Designator
Switching power supply
System board 24-pin power connector
P1
Switching power supply
System board 8-pin power connector
P11
Switching power supply
System board 4-pin power connector
P2
Switching power supply
System board power backplane connector
P10
Switching power supply
4 LFF HDD hot-plug Backplane power
connector
P4
The following tables provide the system board designators that various cables plug into. For more
detailed information about system board components, see “Figure 93 System Board Components”.
Removal and replacement procedures
35
Table 7 Cable Connections from the System Board
Cable
To
System Board Designator
20-pin front panel connector
Front panel
J98
Front panel USB 2.0 port
Front panel USB 2.0
J8
SD card USB 2.0 port
SD reader module
J81
Internal USB 2.0 port
Internal USB cable kit
J49
24-pin power connector
Power supply
J52
8-pin power connector
Power supply
J53
4-pin power connector
Power supply
J54
3-pin backplane I2C connector
Backplane
J68
16-pin power backplane control connector
Power supply
J55
6-pin system fan 1 connector
System fan 1
J61
6-pin system fan 2 connector
System fan 2
J62
6-pin system fan 3 connector
System fan 3
J63
6-pin system fan 4 connector
System fan 4
J64
6-pin system fan 5 connector
System fan 5
J65
6-pin system fan 6 connector
System fan 6
J66
6-pin system fan 7 connector
System fan 7
J69
Table 8 Drive Cable Connections / 4 3.5” LFF Hot-plug HDD Model
Cable
To
System Board Designator
Mini-SAS connector for SATA
Backplane
J13
Table 9 Drive Cable Connections / 8 2.5” SFF Hot-plug HDD Model
Cable
To
System Board Designator
PCI storage controller card (LP)
8 2.5” SFF HDD backplane 3rd party mini SAS
connector
PCI storage controller card (LP)
8 2.5” SFF HDD backplane 3rd party mini SAS
connector
Drive bay configuration
The server supports a maximum of 5 to 9 drive bays --- 4 drive bays for 3.5 in. LFF hard disk drives
and 1 drive bay for 9.5mm (0.37 in.) optical disc drive, or 8 drive bays for 2.5 in. SFF hard disk
drives and 1 drive bay for 9.5mm (0.37 in.) optical disc drive.
Removal and replacement procedures
36
Figure 4 System Drive Bays / 4 3.5” LFF HDD Hot-plug Model
Item
Description
1
9.5mm (0.37 in.) DVD ROM optical drive (optional)
2
3.5 in. hard disk drive bays (4)
The HDD bays support both SAS and SATA drives.
Figure 5 System Drive Bays / 4 3.5” LFF HDD Non-hot-plug Model
Item
Description
1
9.5mm (0.37 in.) DVD ROM optical drive (optional)
2
3.5 in. hard disk drive bays (4)
The HDD bays support SATA drives.
Removal and replacement procedures
37
Figure 6 System Drive Bays / 8 2.5” SFF HDD Hot-plug Model
Item
Description
1
9.5mm (0.37 in.) DVD ROM optical drive
2
2.5 in. hard disk drive bays (8)
The HDD bays only support SAS drives.
Removal and replacement procedures
38
Optical Media Device Bay
The optical media device bay of servers with 4 LFF HDDs and 8 SFF HDDs support the optional
installation of a 9.5 mm (0.37 in.) DVD ROM optical drive, so the following procedure is for server
with 4 LFF HDDs.
To remove the optical drive carrier:
1.
Remove the top cover and then unplug the SATA and power cables.
2.
Loosen the screws.
Figure 7 Removing the Cables and Screws
3.
Push the optical drive toward the front of the unit.
4.
Pull the optical drive out of the chassis.
Figure 8 Removing the Optical Drive
Removal and replacement procedures
39
IMPORTANT: If you removed an optical drive without plans of installing a new one, you must
reinstall the blank to maintain proper system airflow.
To remove the bezel blank:
1.
Turn off the server and all the peripherals connected to it.
2.
Unplug all external cables and AC power cords. If necessary, label each one to expedite
reassembly.
3.
Remove the unit from the rack and place on a flat surface.
4.
Remove the top cover.
5.
Pull the bezel blank out of the carrier.
CAUTION: Do not discard the bezel blank. If the optical drive is removed in the future, you must
reinstall the bezel blank to maintain proper system function.
Figure 9 Removing the Bezel Blank
To install the optical drive:
1.
Slide the optical drive assembly into the chassis.
2.
Remove the top cover, fasten the screws and connect the IDE data and power cables to their
corresponding connectors on the optical drive.
Removal and replacement procedures
40
Figure 10 Installing the Optical Drive
Hard drives
The drive bays on the front panel can accommodate up to four LFF or eight SFF hard drives. You can
install SAS or SATA hard drives in the server.
For servers with 4 LFF HDDs, the hard drives installed in the server are labeled from Device 1 to
Device 4, from left to right, when viewed from the front of the server.
Figure 11 Hard Drive Configuration / 4 3.5” LFF HDD Hot-plug Model
Item
Description
1
1st SAS/SATA hard drive
2
2nd SAS/SATA hard drive
3
3rd SAS/SATA hard drive
Removal and replacement procedures
41
Item
Description
4
4th SAS/SATA hard drive
Figure 12 Hard Drive Configuration / 4 3.5” LFF HDD Non-hot-plug Model
Item
Description
1
1st SAS/SATA hard drive
2
2nd SAS/SATA hard drive
3
3rd SAS/SATA hard drive
4
4th SAS/SATA hard drive
Removal and replacement procedures
42
For servers with 8 SFF HDDs, the hard drives installed in the server are labeled from Device 1 to
Device 8, from top to bottom, left to right, when viewed from the front of the server.
Figure 13 Hard Drive Configuration / 8 2.5” SFF HDD Hot-plug Model
Item
Description
1
1st SAS hard drive
2
3rd SAS hard drive
3
5th SAS hard drive
4
2nd SAS hard drive
5
4th SAS hard drive
6
6th SAS hard drive
7
7th SAS hard drive
8
8th SAS hard drive
The hot-plug HDD for the servers with 4 3.5” LFF HDDs and 8 2.5” SFF HDDs share the same
replacement procedures. Here we take the server with 4 3.5” LFF HDDs as an example for your
reference.
To remove the hot-plug hard drive:
1.
Press the hard disk carrier button to release the ejector lever.
2.
Use the HDD carrier latch to pull the drive out of the cage.
Make sure to support the drive when pulling it out of the cage.
3.
Pull the hard drive assembly out of the drive bay.
Removal and replacement procedures
43
Figure 14 Removing the Hot-plug Hard Drive Assembly
To install the hot-plug hard drive:
1.
Press the release tabs, and then pull the hard drive blank out of the chassis.
Figure 15 Removing the Hot-plug Hard Drive Blank
IMPORTANT: Do not discard the hard drive blank. If the drive is removed in the future, you must
reinstall the hard drive blank to maintain proper system airflow.
2.
Install a hard drive.
a. Push the hard drive assembly into the drive bay until it stops.
b. Press the HDD carrier latch inward until it clicks.
Removal and replacement procedures
44
Figure 16 Installing the Hot-plug Hard Drive Assembly
To remove the non-hot-plug hard drive:
1.
Loosen the screw with the T-10/T-15 wrench provided.
Figure 17 Loosening the Screw
2.
Push the hard drive toward the front of the unit.
3.
Pull the hard drive assembly out of the drive bay.
Removal and replacement procedures
45
Figure 18 Removing the Non-hot-plug Hard Drive Assembly
To remove a non-hot-plug hard drive disk from the carrier:
1.
Loosen the four screws on the carrier (two on each side).
2.
Lift the hard drive from the carrier.
Figure 19 Removing the Non-hot-plug Hard Drive Disk
Removal and replacement procedures
46
To install a non-hot-plug hard drive:
1.
Put the non-hot-plug hard drive disk into the carrier.
2.
Fasten the HDD to the carrier using the screws (two on each side).
Figure 20 Installing the Non-hot-plug Hard Drive Disk into the Carrier
To install a non-hot-plug hard drive into the server:
1.
Remove the hard drive blank from the front of the system if installed.
2.
Push the hard drive assembly into the drive bay until it stops.
Figure 21 Installing the Non-hot-plug Hard Drive Assembly
3.
Fasten the screw with the T-10/T-15 wrench provided to secure the hard drive to the chassis.
Removal and replacement procedures
47
Figure 22 Fastening the Screw
SAS/SATA HDD backplane
The following figures show the front and back side of the backplane.
Figure 23 SATA Backplane Connectors / 4 3.5” LFF HDD Hot-plug Model (component side)
Item
Description
1
Screw holes
2
LED indicators
3
Headers for hard drive
Removal and replacement procedures
48
Figure 24 SAS Backplane Connectors / 8 2.5” SFF HDD Hot-plug Model (component side)
Item
Description
1
Screw holes
2
LED indicators
3
Headers for hard drive
Figure 25 SATA Backplane Connectors / 4 3.5” LFF HDD Hot-plug Model (solder side)
Item
Description
1
Power connector
2
I2C connector
3
SGPIO connector
Removal and replacement procedures
49
Item
Description
4
SATA connectors
Figure 26 SAS Backplane Connectors / 8 2.5” SFF HDD Model (solder side)
Item
Description
1
PIC 1 PROG connector
2
Power connector
3
I2C connector
4
PIC 2 PROG connector
5
Mini SAS connectors
Removal and replacement procedures
50
Cable Routing
Cable routing for hot-plug SAS model:
Figure 27 Cable for Hot-plug SAS Model
Item
Description
1-4
Mini-SAS Host Fan Out 4 SATA cable
5
SATA ODD cable
6
HDD backplane I2C cable
7
HDD backplane SGPIO cable
8
SD card reader cable (optional)
9
BBWC/FBWC cable
Removal and replacement procedures
51
Cable routing for pluggable SATA model:
Figure 28 Cable for Pluggable SATA Model
Item
Description
1-4
Mini-SAS Host Fan Out 4 SATA cable
5
SATA ODD cable
6
HDD backplane I2C cable
7
HDD backplane SGPIO cable
8
SD card reader cable (optional)
WARNING: Ensure that the system is powered off and all power sources have been disconnected
from the server. Voltages are present at various locations within the server whenever an AC power
source is connected. This voltage is present even when the main power switch is in the off position.
To remove the backplane:
The backplanes for the servers with 4 LFF HDDs and 8 SFF HDDs share the same replacement
procedures. Here we take the SAS/SATA backplane for the server with 4 LFF HDDs as an example
for your reference.
1.
Remove all drives out of the drive bays.
2.
Refer to the “Optical Media Device Bay” and “Hard drives” sections in this chapter for detailed
procedures.
3.
Remove the top cover.
4.
Remove all cables connected to the backplane.
5.
Remove the hard drive cage.
a. Loosen all screws that secure the hard drive cage to the chassis.
b. Slide the hard drive cage out and then lift it up. Remove the hard drive cage from the chassis.
Removal and replacement procedures
52
Figure 29 Removing the Hard Drive Cage
6.
Remove the backplane.
a. Remove all cables including optical drive cables.
b. Remove the three screws that secure the backplane to the hard drive cage.
c.
Pull the backplane up and out to release it from the hard drive cage.
Figure 30 Removing the Backplane
To reinstall the backplane:
1.
Orient the backplane so that the notches on the backplane align with the hook on the drive cage
and then press the backplane down until it clicks into place.
2.
Secure the backplane with three screws.
Removal and replacement procedures
53
Figure 31 Reinstalling the Backplane
3.
Install all cables.
Removal and replacement procedures
54
System board configuration
Processor
HP ProLiant DL165 G7 Server supports AMD 8-core/12-core G34-Magny-Cours processors. If a
single processor is installed, then use socket 1. When two processors are used, the server supports
boot functions through the processor installed in socket 1. However, if processor 1 fails, the system
cannot boot up, and if processor 2 fails, the system will be automatically booted from processor 1
and provide a processor failure message.
The processor socket supports 2P AMD G34-Magny-Cours processor with integrated memory
controller.
CAUTION: It is recommended to use processors of the same speeds or cache sizes to prevent
possible server malfunction.
Figure 32 Processor Locations
Item
Description
1
Processor 1
2
Processor 2
WARNING: To reduce the risk of personal injury from hot surfaces, allow the heat sink and the
processor to cool before touching them.
NOTE: Before installing the processor, remove the air baffle.
Removal and replacement procedures
55
To remove the air baffle:
1.
Gently rock the air baffle up.
2.
Take the air baffle out from the system board.
Figure 33 Removing the Air Baffle
NOTE: Due to the position of the two processors in the chassis, the heat sink of processor 2 blocks
the air from the system fans to the heat sink of processor 1, which results in insufficient cooling to
processor 1. In order to reach the system required thermal performance, the system is designed with
two different heat sinks. Please make sure to install the two heat sinks in the correct position.
To remove the heat sink:
1.
Loosen the two spring-loaded screws.
2.
Lift the heat sink away from the system board.
CAUTION: Place the heat sink down in an upright position with the thermal patch facing upward.
Do not let the thermal patch touch the work surface.
Removal and replacement procedures
56
Figure 34 Removing the Heat Sink of Processor 1
Figure 35 Removing the Heat Sink of Processor 2
IMPORTANT: If the heat sink has been removed for any reason on a previously installed processor, it
is critical that you remove any residual thermal compound using the provided alcohol pads and
apply more grease compound to the integrated heat spreader on the processor to ensure proper
thermal bonding between the processor and the heat sink.
CAUTION: Do not over-tighten the spring-loaded screws to prevent them from breaking off. A
maximum torque of 6 inch-lb is set for each screw. Rotate the heat sink a few degrees to the left and
right to break the bonding of the thermal grease compound before removing the heat sink from the
processor.
Removal and replacement procedures
57
To remove the processor:
1.
Unlock the load lever and lift it up.
2.
Open the retention plate.
3.
Squeeze the push fingers of the processor installation tool.
4.
Hold the processor with the installation tool.
Figure 36 Picking up the Processor from the Socket with the Installation Tool
5.
Remove the processor with the installation tool.
Figure 37 Removing the Processor
NOTE: If the processor installation tool is not included, grasp the processor by its edges and lift it
out of the socket.
CAUTION: The pins of the socket are very fragile. Do not bend or damage them.
CAUTION: Place the processor on a static-dissipating work surface or in an anti-static bag.
Removal and replacement procedures
58
CAUTION: To allow heat sink to draw as much heat as possible from the processor base, there must
be good contact between the heat sink base and the top of the processor. To ensure good contact,
you must apply thermal grease compound.
To install the new processor:
1.
Squeeze the push fingers of the processor installation tool.
2.
Align the tool on the processor; release the push fingers and hold the processor.
Figure 38 Picking up the Processor with the Installation Tool
3.
Insert the processor into the socket.
Figure 39 Aligning and Inserting the Processor
4.
Squeeze the push fingers of the processor installation tool to release the processor.
5.
Remove the processor installation tool.
6.
Engage the retention plate.
7.
Engage the load lever.
Removal and replacement procedures
59
Figure 40 Installing the Processor
NOTE: If the processor installation tool is not included, grasp the processor by its edges and install it
into the socket.
CAUTION: With the load lever and the retention plate disengaged, hold the processor by its edges
and align it over the empty processor socket. Make sure that you properly align the processor with
the orientation notch on the socket.
To apply the thermal grease compound:
1.
Use a clean cloth dipped in rubbing alcohol to clean the contact surface on the heat sink and the
new processor. Wipe the contact surfaces several times to make sure that no particles or dust
contaminants are evident.
2.
Apply the thermal grease compound to the integrated heat spreader on the processor in one of
the following patterns to insure even distribution.
CAUTION: HP recommends using Shin-Etsu X-23-7783D thermal grease compound for your ProLiant server.
Apply the grease to the top of the processor in either a 5 “Dot” or “S” shaped pattern. Ensure even
distribution.
Removal and replacement procedures
60
Figure 41 The top of the processor
CAUTION: Never touch the bottom of the processor; any contaminant could prevent the mounting
pads from making contact with the socket.
CAUTION: Applying too much grease creates a gap between the contact surfaces, significantly
reducing the ability of the heat sink to draw out heat. Installing the heat sink with excessive grease
can also cause the grease to spread over the processor pins or the system board base, which can
cause electrical shorts that damage the system.
CAUTION: To prevent overheating or a possible system crash, use only a heat sink model specified
for the HP ProLiant DL165 G7 server.
Removal and replacement procedures
61
To install the heat sink:
1.
Properly align the heat sink spring-loaded screws to the system board mounting holes.
2.
Tighten the spring-loaded screws clockwise to secure the heat sink connection to the system
board.
Figure 42 Installing the Heat Sink of Processor 1
Figure 43 Installing the Heat Sink of Processor 2
CAUTION: When installing two heat sinks, please put the heat sinks with the 27-fin side facing the
DIMMs.
CAUTION: For proper cooling, do not operate the server without the top cover, air baffle, expansion
slot covers, or blanks installed. For additional information, see the user guide. If hot-plug
components are supported, minimize the amount of time the top cover is removed.
Removal and replacement procedures
62
To install the air baffle:
1.
Connect all necessary cables.
2.
Gently place the air baffle on the system board.
Figure 44 Installing the Air Baffle
Memory
Each system board has twenty-four DIMM slots that support up to 192 GB maximum system memory
(8 GB in each of the twenty-four DIMM slots).
You must adhere to the following guidelines when adding or replacing memory modules:
•
•
•
For 2P system, both physical processors must be of the same type and speed.
Use DDR3 RDIMM/UDIMM.
Support single-rank, dual-rank, and quad-rank DIMM.
Removal and replacement procedures
63
Memory module population order
Processor memory
socket
1
2
3
4
5
6
7
8
9
10
11
12
Rank support per
memory socket
SR/DR
SR/DR/
QR
SR/DR
SR/DR
SR/DR/
QR
SR/DR
SR/DR
SR/DR/
QR
SR/DR
SR/DR
SR/DR/
QR
SR/DR
RDIMM Population
order without QR
A
I
E
C
K
G
B
J
F
D
L
H
UDIMM Population
order without QR
A
E
C
G
B
F
D
Population order with
QR along with SR/DR
E
A
I
G
C
K
F
B
J
H
D
L
Processor memory
bank number
1
3
2
1
3
2
1
3
2
1
3
2
H
NOTES:
SR = Single Rank, DR = Dual Rank, QR = Quad Rank.
Population rules must be followed for both processors. DIMMs must be populated in alphabetic order (A, B, C…) as indicated in the matrix.
Memory modules may be populated one at a time per processor, but populating two at a time per processor provides better performance.
Memory modules should be populated four at a time per processor for best performance.
Memory modules within a memory bank must be identical for best performance.
Quad Rank memory module can only be installed in memory sockets 2, 5, 8, and 11.
Figure 45 DIMM Slots
NOTE: Before installing the memory, remove the air baffle first. For a detailed procedure, see
the ”Processor” section in this chapter.
Removal and replacement procedures
64
To remove the memory module:
1.
Completely open the holding clips securing the memory module.
2.
Gently pull the memory module upward to remove it from the slot.
Figure 46 Removing the Memory Module
CAUTION: Place the memory module on a static-dissipating work surface or inside of an anti-static
bag.
To install the memory module:
1.
Align the notch on the bottom edge of the memory module with the keyed surface of the DIMM
slot and then fully press the memory module into the slot until the holding clips snap back in
place.
Figure 47 Installing the Memory Module
CAUTION: The DIMM slots are structured to ensure proper installation. If you insert a DIMM but it
does not fit easily into the slot, you may have inserted it incorrectly. Reverse the orientation of the
DIMM and insert it again.
Removal and replacement procedures
65
PCI expansion card
System board PCI expansion slot
There is one PCI expansion slot on the system board.
Figure 48 System Board PCI Expansion Slot
Item
Component
Designator
Component
Function
1
J30
PCIe X16 (LP) slot 1
Support a PCIe riser card
Removal and replacement procedures
66
System board storage card slot
There is one storage card slot on each system board.
Figure 49 System Board Storage Card Slot
Component
Designator
Component
Function
J78
PCIe x4 (LP) slot (storage card slot)
Supports a PCIe riser card
Removal and replacement procedures
67
PCI riser card expansion slot
The two PCIe riser card attached to the PCI cage convert the functionality of the system board
expansion slot to the slot positioned at a 90° angle from the system board.
Figure 50 PCIe x16 Riser Card Connector Location
•
Single-slot PCIe riser card (x16 link with x16 slot)
Figure 51 PCIe x8 Riser Card Connector Location
•
Single-slot PCIe riser card (x4 link with x8 slot)
Removal and replacement procedures
68
PCI cage
To remove the PCI cage:
NOTE: Disconnect all cables connecting an existing expansion board to the system board.
1.
Loosen the four screws that secure the PCI cage to the system board tray.
2.
Lift the PCI cage away from the system board assembly.
Figure 52 Removing the PCI Cage
Installing PCIe riser cards
The system supports up to two riser cards at a time. Use only HP supported expansion boards that
meet the following specifications:
•
Compliance
○ PCIe x16
○ PCIe x8
•
Form Factor
○ Low Profile
Removal and replacement procedures
69
To remove the PCIe riser card:
1.
Loosen the two screws securing the riser card to the PCI cage.
2.
Remove the riser card from the PCI cage.
Figure 53 Removing the PCIe x16 Riser Card
Figure 54 Removing the PCIe x8 Riser Card
Removal and replacement procedures
70
To install the PCIe riser card:
1.
Align the screw holes on the riser card to the screw holes on the PCI cage.
2.
Install and tighten the screws that secure the riser card to the PCI cage.
Figure 55 Installing the PCIe x16 Riser Card
Figure 56 Installing the PCIe x8 Riser Card
Removal and replacement procedures
71
To install the PCI expansion board:
1.
Remove the slot cover from the PCI cage.
2.
Slide the expansion board into the slot, aligning the board with its matching connector.
Firmly press the board to seat it properly on the slot.
3.
Fasten the screw to secure it.
Figure 57 Installing the PCI Expansion Board
Figure 58 Installing the Storage Card
CAUTION: Do not discard the slot cover. If the expansion board is removed in the future, the slot
cover must be reinstalled to maintain proper cooling.
Removal and replacement procedures
72
Table 10 HP Smart Array Controller Spare Parts List
Item
Description
Spare Part
Number
Customer Self
Repair
1
HP Smart Array P212 Controller
462594-001
Mandatory
2
HP Smart Array P410 Controller
462919-001
Mandatory
3
HP Smart Array P411 Controller
462918-001
Mandatory
4
HP Smart Array P812 Controller
587224-001
Mandatory
Table 11 HP Smart Array Cache Module Spare Parts List
Item
Description
Spare Part
Number
Customer Self
Repair
1
Smart Array cache module, 256 MB (Smart Array P212, P410
and P411 controllers only)
462974-001
Mandatory
2
Smart Array cache module, 512 MB (Smart Array P212, P410
and P411 controllers only)
462975-001
Mandatory
3
FBWC capacitor pack
587324-001
Mandatory
4
FBWC module, 512-MB
578882-001
Mandatory
5
FBWC module, 1-GB
505908-001
Mandatory
To reinstall the PCI cage:
1.
Install the PCI expansion board into the PCI cage.
a. Align the PCI expansion board with the open expansion slot.
b. Press the PCI expansion board into the expansion slot on the riser card.
2.
Align the PCI cage to the system board expansion slot, and then press it down to ensure full
connection to the system board.
3.
Tighten the four screws to secure the PCI cage to the chassis.
Removal and replacement procedures
73
Figure 59 Reinstalling the PCI Cage with PCI Expansion Board
Figure 60 Reinstalling the PCI Cage with Storage Card
4.
Connect the necessary cable(s) to the system board.
Removal and replacement procedures
74
System battery
The server uses nonvolatile memory that requires a system battery to retain system information when
power is removed.
This 3 V lithium coin cell battery is located on the system board.
Figure 61 System Battery Location
WARNING: Note the following reminders when replacing the system battery:
• Replace the system battery with the same type as the system battery recommended by HP. Use of
another system battery may present a risk of fire or explosion.
• A risk of fire and chemical burn exists if the system battery is not handled properly. Do not
disassemble, crush, puncture, or short external contacts, or expose the system battery to
temperatures higher than 60°C (140°F).
• Do not dispose of used system battery in water or fire. Dispose of used system battery according
to manufacturer's instructions.
CAUTION: Loss of BIOS settings occurs when the system battery is removed. You must reconfigure
BIOS settings whenever you replace the system battery.
NOTE: If the server no longer automatically displays the correct date and time, you may need to
replace the system battery. Under normal usage, system battery life is five to ten years.
To replace the system battery:
1.
Power down the server.
2.
Disconnect the power cord(s).
3.
Unlock the server if necessary and remove the top cover as described in the section “System
cover”.
NOTE: If the expansion board is installed to the PCI cage, remove the PCI cage before releasing the
battery. Refer to the “PCI cage” section in this chapter for detailed procedures.
4.
Release the battery from its holder by squeezing the metal clamp that extends above one edge of
the battery. When the battery pops up, lift it out.
Removal and replacement procedures
75
5.
To insert the new battery, slide one edge of the replacement battery under the holder’s lip with
the positive side up. Push the other edge down until the clamp snaps over the other edge of the
battery.
Figure 62 Replacing the System Battery
BBWC (Optional)
This server can support a BBWC. The BBWC is optional for the shipment.
Figure 63 BBWC Location
Removal and replacement procedures
76
To remove the BBWC assembly:
1.
Push the tab that secures the BBWC assembly to the system board tray.
2.
Slide the BBWC assembly, and then lift it out of the system board assembly.
Figure 64 Removing the BBWC Assembly
To reinstall the BBWC assembly:
1.
Align the locking tabs on the BBWC assembly to their holes on the tray.
2.
Press the BBWC assembly into the tray, and then push it along the direction of the arrow to lock
the locking tabs.
Figure 65 Reinstalling the BBWC Assembly
Removal and replacement procedures
77
SD card reader module (Optional)
This server can support a SD reader module. The SD reader module is optional for the shipment.
Figure 66 SD Reader Module Location
To remove the SD card reader module:
1.
Disconnect the USB cable from the SD card reader module USB connector.
Figure 67 Disconnecting the SD Card Reader Module USB Cable
2.
Loosen the screw that secures the SD card reader module to the chassis.
3.
Remove the SD card reader module from the chassis.
Removal and replacement procedures
78
Figure 68 Removing the SD Reader Module
To reinstall the SD card reader module:
1.
Remove the SD card reader module knock-out from the back panel of the server.
Figure 69 Removing the SD Reader Module Knock-out
2.
Align the SD card reader module to the back panel, and tighten the screw that secures the
module to the chassis.
Removal and replacement procedures
79
Figure 70 Reinstalling the SD Reader Module
3.
Connect the USB cable to the SD card reader module USB connector and link the other side of
the USB cable connector to the system board. (Refer to your system hood label for the connector
locations.)
Figure 71 Connecting the SD Reader Module USB Cable
Removal and replacement procedures
80
Mgmt card (Optional)
The server can support a mgmt card. The mgmt card is optional for the shipment.
The following figure shows the mgmt card location.
Figure 72 Mgmt Card Location
To remove the mgmt card:
1.
Loosen the screw.
2.
Pull the mgmt card upwards, and then remove the mgmt card from the mgmt card connector.
Figure 73 Removing the Mgmt Card
Removal and replacement procedures
81
To reinstall the mgmt card:
1.
Remove the mgmt port knock-out.
Figure 74 Removing the Mgmt Port Knock-out
2.
Insert the mgmt card into the mgmt card connector on the system board.
3.
Tighten the screw clockwise to secure the mgmt card to the system board.
Figure 75 Reinstalling the Mgmt Card
Removal and replacement procedures
82
System board removal and replacement procedure
To remove the system board:
1.
Remove the top cover.
2.
Remove the air baffle and all cables from the system board.
3.
Loosen the nine screws that secure the system board to the chassis.
4.
Slide the system board back, up and out of the chassis. Remove the system board from the
chassis.
Figure 76 Removing the System Board
NOTE: Extreme care must be taken to ensure the system board components on the bottom of the
system board not be scraped or dislodged by the screw standoffs. The sliding action requires that
the rear panel should be cleared slightly and the front of the system board should be raised slightly
as you move the system board towards the front and up.
Removal and replacement procedures
83
To reinstall the system board:
1.
Align the system board I/O connectors to their openings and slide the system board into place.
The nine screw holes on the chassis should align with the system board.
2.
Fasten the nine screws on the system board to secure the system board to the chassis.
Figure 77 Reinstalling the System Board
NOTE: Upon completion of replacing the system board, go to the HP website and download the
latest system BIOS firmware for the DL165 G7. The replacement system board may not have the
latest firmware.
Removal and replacement procedures
84
Power supply unit (PSU)
Located on the rear panel of the server power supply is a standard autoranging 750 W or 500 W
non-hot-plug PSU.
Figure 78 Hot-plug Power Supply Unit
To remove the hot-plug power supply:
1.
Press the purple tab.
2.
Pull the hot-plug power supply out of the power supply bay
Figure 79 Removing the Hot-plug Power Supply
To reinstall the hot-plug power supply:
1.
Align the hot-plug power supply cage connector with the open power supply bay and slide the
power supply into the chassis.
2.
Push it in until the locking tab is clicked.
Removal and replacement procedures
85
Figure 80 Reinstalling the Hot-plug Power Supply
Figure 81 Non-hot-plug Power Supply Unit
To remove the non-hot-plug power supply:
1.
Loosen the two screws that secure the power supply, which are located beneath the chassis.
Removal and replacement procedures
86
Figure 82 Loosening the Two Screws beneath the Chassis
2.
Loosen the screws that secure the power supply to the chassis.
3.
Pull and lift the power supply out of the chassis.
Figure 83 Removing the Non-hot-plug Power Supply
Removal and replacement procedures
87
To reinstall the non-hot-plug power supply:
1.
Locate and push the power supply to the proper place in the chassis.
2.
Fasten the power supply to the chassis using the screws as shown in the figure below.
Figure 84 Reinstalling the Non-hot-plug Power Supply
3.
Fasten the two screws which are located beneath the chassis to secure the power supply
Figure 85 Fastening the Two Screws beneath the Chassis
WARNING: Take note of the following reminders to reduce the risk of personal injury from electric
shock hazards and/or damage to the equipment.
• Installation of power supply units should be referred to individuals who are qualified to service
server systems and are trained to deal with equipment capability of generating hazardous
energy levels.
• DO not open the power supply unit. There are no serviceable parts inside it.
Removal and replacement procedures
88
System fan
The server can support up to seven system fans located on the center wall of the chassis. When the
server is installed with one processor, the system fans should be installed in the 2nd, 4th, 5th and 6th
system fan locations. When the server is installed with two processors, the redundant fan functions are
supported by the system fan 1, system fan 3, and system fan 7 when installed.
Figure 86 System Fan Connections for One Processor Configuration
Figure 87 System Fan Connections for Two Processors Configuration with N+1 Redundancy Fan
Device number
Connector
System fan 1
J61 on the system board
System fan 2
J62 on the system board
System fan 3
J63 on the system board
System fan 4
J64 on the system board
Removal and replacement procedures
89
Device number
Connector
System fan 5
J65 on the system board
System fan 6
J66 on the system board
System fan 7
J69 on the system board
A new system fan can be installed to allow the server to operate properly in case a default system fan
becomes defective.
To remove the system fan:
1.
Power down the server.
2.
Disconnect the power cord(s).
3.
Unlock the server if necessary and remove the top cover as described in the section “System
cover”.
4.
Disconnect the system fan cable from its corresponding board connector.
5.
Release the fan cable from the cable clip securing it to the chassis partition wall.
6.
Lift the system fan away from the chassis.
Figure 88 Removing the System Fan
To reinstall the system fan:
1.
Put the system fan cable through the system fan cage.
2.
Hold the system fan and press the system fan into the system fan bracket.
3.
Connect the system fan cable to its corresponding board connector.
Removal and replacement procedures
90
Figure 89 Reinstalling the System Fan
Removal and replacement procedures
91
Connectors, switches, and LEDs
This chapter contains illustrations and tables identifying and describing the connectors, jumpers,
switch, buttons, and LED indicators located on the front panel, rear panel, system board and hard
drives of the HP ProLiant DL165 G7 server.
Connectors and components
Front panel components
Figure 90 Front Panel Components / 4 3.5” LFF HDD Hot-plug Model
Item
Description
1
Thumbscrews for rack mounting
2
Drive online/error LED
3
Drive activity LED
4
Optical disc drive (optional)
5
Serial number pull tab
6
Front panel USB 2.0 port 1/2
7
Front UID LED/switch
8
System health LED
9
NIC 1/2 activity LED
10
Power LED/switch
11
Hard drive activity LED
Connectors, switches, and LEDs
92
Item
Description
12
NIC 3/4 activity LED
13
Hard disk drive (HDD) bays
Figure 91 Front Panel Components / 8 2.5” SFF Hot-plug HDD Model
Item
Description
1
Thumbscrews for rack mounting
2
Drive online/error LED
3
Drive activity LED
4
Serial number pull tab
5
Optical disc drive
6
Front panel USB 2.0 port 1/2
7
Front UID LED/switch
8
Hard drive activity LED
9
Power LED/switch
10
NIC 3/4 activity LED
11
NIC 1/2 activity LED
12
System health LED
13
Hard disk drive (HDD) bays
Connectors, switches, and LEDs
93
Rear panel components
Figure 92 Rear Panel Components
Item
Description
1
Power supply cable socket
2
SD card reader port (optional)
3
Rear UID LED/switch
4
Mgmt port (optional)
5
Serial port
6
GbE LAN port for NIC 4
7
Full-height/full-length PCI expansion card slot cover
8
T-10/T-15 wrench
9
Screw for PCI cage
10
GbE LAN port for NIC 1
11
GbE LAN port for NIC 2
12
VGA port
13
GbE LAN port for NIC 3
14
Rear panel USB 2.0 port 0/1
Connectors, switches, and LEDs
94
System board components
Figure 93 System Board Components
Item
Designator
Description
1
J1
System maintenance jumper
2
J301
PCIe x16 slot
3
CPU1
Processor 1
4
J11
Mgmt card connector
5
J110
DIMM slot 12 for processor 1
6
J103
DIMM slot 1 for processor 1
7
J210
DIMM slot 12 for processor 2
8
CPU2
Processor 2
9
J54
4-pin power connector
10
J52
24-pin power connector
11
J61
Fan connector 1
12
J62
Fan connector 2
13
J203
DIMM slot 1 for processor 2
14
J65
Backplane I2C connector
15
J53
8-pin power connector
16
J63, J64
Fan connectors 3/4
17
J65
Fan connector 5
18
J49
Internal USB 2.0 port
19
J81
SD card USB 2.0 port
20
J8
Front panel USB 2.0 port
Connectors, switches, and LEDs
95
Item
Designator
Description
21
J100
SAS LED connector
22
J36, J69
Fan connectors 6/7
23
J13
Mini-SAS connector for SATA
24
J55
Power backplane control connector
25
J98
Front panel header
26
J56
TPM connector
27
J78
PCIe x4 slot
28
SATA
ODD 2 SATA connector
29
SATA
ODD 1 SATA connector
30
BH1
3 V CMOS battery (CR2032)
31
J6
NMI Jumper
Jumper
The system board contains a system maintenance jumper (J1). Table 12 describes the jumper settings.
Table 12 System Maintenance Jumper Setting (J1)
Jumper
Status (default=off)
A
Clear BMC password
B
Recovery BMC
C
Recovery BIOS
D
Clear CMOS
LED indicators
This section contains illustration and descriptions of internal and external status LED indicators located
on the:
•
•
•
•
•
Front panel
Optical drive
Hard drive
Rear panel
System board
These LED indicators aid in problem diagnosis by indicating the status of system components and
operations of the server.
Connectors, switches, and LEDs
96
Front panel LED indicators
The front panel LED indicators allow constant monitoring of basic system functions while the server is
operating.
Figure 94 Front Panel LED Indicators
Table 13 Front Panel LED Indicator Status
Item
LED indicator
Status
Description
1
Front UID LED/switch
Steady blue
Identification.
Flashing blue
The system is being remotely managed.
Off
No identification.
Steady green
System is powering on and normal.
Flashing red
System is powering on or off and critical.
Flashing amber
System is powering on or off and degraded.
Off
System is powering off and normal.
Steady green
Linked to the network.
Flashing green
Linked and activity on the network.
Off
No connection.
Steady green
Linked to the network.
Flashing green
Linked and activity on the network.
Off
No connection.
Flashing green
Hard drive activity.
Off
No hard drive activity.
Steady green
The system has AC power and is turned on.
Flashing green
The system is requesting power-on.
2
3
4
5
6
System health LED
NIC 1 activity LED
NIC 2 activity LED
Hard drive activity LED
Power LED/switch
Connectors, switches, and LEDs
97
Table 13 Front Panel LED Indicator Status
Item
LED indicator
Status
Description
Steady amber
The system has AC power but in standby
mode or denies power-on.
Off
No AC power to the system.
Optical drive activity LED indicator
The optical drive has an activity indicator that indicates when the drive is reading media.
Figure 95 Optical drive activity LED indicator
Table 14 Optical Drive Activity LED Indicator Status
Item
LED indicator
Status
Description
1
Optical drive activity LED
indicator
Flashing green
Ongoing drive activity
Off
No drive activity
Connectors, switches, and LEDs
98
Hard Drive LED indicators
The status of hard drives installed in the server is indicated by the online LED indicator located on the
HDD.
Figure 96 Hard Drive LED Indicator
Table 15 Hard Drive LED Indicator Status
Item
LED indicator
Status
Description
1
Drive online/error LED indicator
Steady blue
The drive is located
Steady orange
The drive is in a failed state.
Off
The drive is not in a failed state.
Flashing green
The drive is in an activity state.
Off
The drive is not in an activity state.
2
Drive activity LED indicator
Connectors, switches, and LEDs
99
Rear panel LED indicators
The LAN port on the rear panel has two LED indicators that allow monitoring of network activity.
Figure 97 LAN LED Indicators Location
Table 16 LAN LED Indicator Status
Item
Component
1
Pilot 2 NIC activity LED indicator Flashing amber
LAN is active.
2
Pilot 2 NIC link LED indicator
Steady green
Linking at 100 Mbps speed.
Off
No connection or linking at 10 Mbps
speed.
Steady green
Linking at 10 Mbps / 100 Mbps / 1G /10
G.
Off
No connection or linking at 10 Mbps
speed.
Flashing green
Linked and activity on the network.
Steady green
Linked to the network.
Off
No network activity.
3
4
NIC speed LED indicator (left)
NIC activity LED indicator (right)
Status
Description
Connectors, switches, and LEDs
100
System board LED indicator
Each system board contains one LED indicator for use during troubleshooting operations.
Figure 98 System Board LED Indicator
Table 17 System Board LED Indicator Status
Components
Status
Descriptions
BMC activity LED indicator
Steady green
BMC is power on and in
initialization process
Flashing green
BMC activity
Off
AC is Off
Connectors, switches, and LEDs
101
Diagnostic tools and setup utilities
This chapter provides an overview of the Power-On Self-Test (POST), the POST error messages, and
BIOS, SAS and SATA setup utilities.
BIOS software
The server uses BIOS to boot up the system. BIOS software is a ROM-based firmware that allows
reliability, manageability, and connectivity for the server platforms. This software contains a set of
programs permanently stored in an EEPROM chipset located on the system board. These programs
assist in managing, initializing, and testing the hardware devices installed on the computer.
BIOS software allows you to:
•
Perform configuration from the BIOS Setup Utility
Using the Setup Utility, you can install, configure, and optimize the hardware devices on the
system board. In addition, you can set various features such as serial console redirection, PXE
boot, and much more.
•
Initialize hardware at boot up using POST routines
During power-on or warm reset, the BIOS perform POST routines to test system components,
allocate resource for various hardware devices, and prepare the system to boot to various
operating systems.
BIOS Setup Utility
The HP server BIOS Setup Utility is used to configure five primary menu selections:
•
•
•
•
•
Main
Advanced
Boot
Security
Exit
Accessing the BIOS Setup Utility
1.
Turn on the monitor and server.
2.
If the server is already turned on, save your data and exit all open applications, then restart the
server.
3.
When the HP logo is displayed during POST, press F10 into BIOS Setup Utility. If you fail to
press F10 before POST is completed, you will need to restart the server.
4.
The first page displayed is the Main menu showing the Setup Utility menu bar. Use the “← ” or
”→ ” key to move between selections on the menu bar. Use the <Enter> key to select items within
a menu.
Diagnostic tools and setup utilities 102
Navigating through the Setup Utility
Use the keys listed in the legend bar on the right of the Setup screen to navigate through the various
menu and submenu screens of the Setup Utility. Table 18 lists these legend keys and their respective
functions.
Table 18 Setup Utility Navigation Keys
Key
Function
“← ” or ”→ ”
Select different screens.
Enter
Select items in each menu.
Enter, Tab, or
Shift-Tab
Select a field value or display a submenu screen.
Esc
Exit the CMOS Setup menu.
<+>, <–>
Configure the system time or change field.
F1
Display more options for items marked with
.
To bring up the General Help window.
The General Help window describes other Setup navigation keys that are not displayed
on the legend bar.
F10
To save changes and exit the CMOS Setup Utility.
Setup Utility menu bar
The BIOS Setup Utility provides a menu bar with the menu selections. The menu bar choices are
described in the topics below.
Diagnostic tools and setup utilities
103
Main menu
Figure 99 Main Menu of BIOS Setup Utility (1)
Figure 100 Main Menu of BIOS Setup Utility (2)
Use this menu to configure the following items:
•
•
•
•
View product name.
View processor information and system memory size.
Set system time and date.
View BIOS build date and version.
Diagnostic tools and setup utilities 104
•
•
•
•
View system serial number.
View NIC MAC addresses.
Set asset tag.
Configure POST F1 prompt.
Advanced menu
Figure 101 Advanced Menu of the BIOS Setup Utility
WARNING: Incorrect settings may cause the server to malfunction. To correct the settings, press the
F9 key to restore the default settings.
•
•
•
•
•
•
•
•
•
•
•
•
CPU Configuration—Configure CPU settings.
SATA Configuration—Configure the SATA device(s).
Memory Configuration—Configure the memory settings.
AHCI Configuration—Configure the AHCI settings.
IPMI Configuration—Configure IPMI 2.0 settings.
PCI Express Configuration—Configure PCI Express settings.
Remote Access Configuration—Configure the remote access settings.
Trusted Platform Module—Configure trusted platform module.
USB Configuration—Configure USB settings.
OnBoard Peripherals Configuration—Configure the settings of onboard peripherals.
Virtual Floppy—Disable/Enable virtual floppy. Allow users to load SW RAID driver without
pressing F6 key during MS W2K3 OS installation when Virtual Floppy option is enabled.
Power Efficiency Mode—Select the power efficiency mode.
Diagnostic tools and setup utilities 105
Figure 102 IPMI Submenu of the BIOS Setup Utility
•
•
•
•
•
•
•
•
•
BMC Firmware Revision—Display the version of the BMC hardware and firmware.
BMC/IPMI FW Date—View BMC/IPMI FW date.
BMC SDR Version—View BMC SDR version.
Set LAN Configuration—Set LAN settings.
SEL Configuration—Display BMC event log.
Hardware Health Information—Set temperature and fan rotation rate.
Watchdog Configuration—Configure watch dog timer status.
Serial Port Configuration—Configure serial port connection settings.
Restore after AC Power Loss—Use this screen to restore the AC power setting.
Diagnostic tools and setup utilities 106
Boot menu
Figure 103 Boot Menu of the BIOS Setup Utility
•
•
Boot Settings Configuration—Configure settings during system boot.
•
•
Hard Disk Drives— View the hard disk drives in the system.
Boot Device Priority—Use this screen to specify the order in which the system checks for a boot
device.
USB Drive Boot Priority—Configure priority settings for USB devices. Users can configure the
BIOS to avoid attempting to boot non-bootable USB devices that are left plugged into the server
during POST. The options are High (default) and Low.
Diagnostic tools and setup utilities 107
Security menu
Figure 104 Security Menu of the BIOS Setup Utility
Use this menu to configure the following items:
•
•
•
•
Supervisor Password—Indicate if a supervisor password has been installed to the system.
User Password—Indicate if a user password has been installed to the system.
Change Supervisor Password—Modify or change your supervisor password.
Change User Password—Modify or change the user password.
Diagnostic tools and setup utilities 108
Exit menu
Figure 105 Exit Menu of the BIOS Setup Utility
Use this menu to save changes or discard changes. When you save and exit, the server reboots.
•
•
Save Changes and Exit—Save the changes you have made and exit the BIOS Setup Utility.
•
Discard Changes—Discard (cancel) any changes you have made. F10 can be used for this
operation. You will remain in the Setup Utility.
•
Restore Default Settings—Load optimal default values for all the setup questions
Discard Changes and Exit—Exit the BIOS Setup Utility without saving the changes you have
made.
BIOS update
Please make sure your USB key drive diskette is bootable before unzip.
Please unzip factory or user into the root directory of USB key drive diskette.
Flash system BIOS steps:
1.
Power on the system with USB key drive diskette.
2.
User Tool - Execute the ROMPAQ.EXE
3.
Follow the on-screen instruction to upgrade the system BIOS.
Power-On Self-Test (POST)
Before you can use a server, all devices must be tested and initialized, and the operating system must
be bootstrapped to the memory. This is referred to as Power–On Self-Test or POST. POST is a series of
diagnostic tests that checks firmware and hardware components on the system to ensure that the
server is properly functioning. This diagnostic function automatically runs each time the server is
powered on.
Diagnostic tools and setup utilities 109
These diagnostics, which reside in the BIOS ROM, isolate the server-related logic failures and indicate
the board or component that you need to replace, as indicated by the error messages. Most server
hardware failures will be accurately isolated during POST. The number of tests displayed depends on
the configuration of the server.
During POST you can:
•
Press F10 to access the Setup Utility.
POST error indicators
When POST detects a system failure, it displays a POST error message.
POST related troubleshooting
Perform the following procedures when POST fails to run, displays error messages.
If the POST failure is during a routine boot up, check the following:
•
•
•
All external cables and power cables should be firmly plugged in.
•
•
•
•
•
•
The monitor's contrast and brightness settings are correct.
•
•
All internal cabling and connections are in their proper order.
The power outlet to the server should be connected and works correctly.
The server and monitor are both turned on. The bicolour status LED indicator on the front panel
must be lit up green.
All internal cables are properly connected and all boards firmly seated.
The processor is fully seated in its socket on the system board.
The heat sink assembly is properly installed on top of the processor.
All memory modules are properly installed.
If you have installed a PCI accessory board, verify that the board is firmly seated and any
jumpers on the board are properly set. Refer to the documentation provided with the accessory
board.
If you have changed the jumpers on the system board, verify that each is properly set.
Diagnostic tools and setup utilities 110
Physical and operating specifications
This chapter provides physical and operating specifications for the HP ProLiant DL165 G7 server.
Specifications include:
System unit
Table 19 Hardware Specifications
Item
Components
Processor socket
AMD G34 1944-pin socket
Processor
2P AMD G34 Magny-Cours
Chipset
ATI SR5670/ATI SP5100
Hardware monitoring device
Embedded in ServerEngines Pilot 2 management controller
Gigabit ethernet controller
• Intel 82576 GbE controller for NIC
• LO100i sideband support
Onboard storage controller
ATI SP5100
DVD & Floppy interface
Optional DVD (SATA)
Embedded video controller
ServerEngines Pilot 2 management controller
I/O subsystem
• One PCIe x16 links with x16
• One PCIe x4 links with x8 slot
Memory
Twenty four DDR3 RDIMM/UDIMM slots, up to 192 GB
Default media storage
• Four bays LFF hot-plug HDD cage for 3.5” SAS/SATA drives
• Eight bays SFF hot-plug HDD cage for 2.5” SAS drives
Optical media storage
• One slim optical drive bay for DVD-ROM drive on the front
I/O ports
USB 2.0 ports (two rear USB ports, one internal USB port, two front
USB ports), video port, serial port and GbE port and mgmt port.
Physical and operating specifications
111
Table 19 Hardware Specifications
Item
Components
Status LED indicators
Front panel
Rear panel
System board
Power supply unit
•
•
•
•
•
System Health LED
NIC 1/2 activity LED
Power Switch/LED
Hard drive activity LED indicator
UID Switch/LED
• Rear UID LED/switch
• NIC link LED
• NIC activity LED
• BMC Activity LED
500 W non-hot-plug, power supply
750 W hot-plug, power supply
Thermal solution
Seven system fans
Table 20 Physical Dimensions
Item
Description
System board platform
EATX (Extended Advanced Technology Extended)
System board dimension
304.8 mm x 330.2 mm (12 in x 13 in)
Server dimensions (H x W x D)
43 mm x 448 mm x 713 mm (1.69 in. x 17.64 in. x 28.07 in.)
Rack
Server weight
Basic configuration (excludes monitor): 15 ± 2kg
Table 21 Environmental Specifications
Item
Description
Temperature:
Operating
+10°C to +35°C (+50°F to +95°F)
Non-operating
-30°C to 60°C (-22°F to 140°F)
Storage
-30°C to 60°C (-22°F to 140°F)
Wet-bulb temperature
38.7°C (101.7°F)
Relative humidity:
Operating
5% to 95% (non-condensing)
Non-operating
5% to 95%
Storage
5% to 95%
Physical and operating specifications
112
Table 21 Environmental Specifications
Item
Description
Altitude:
Operating
0 to 3049 m (0 to 10,000 ft)
Non-operating
0 to 9146 m (0 to 30,000 ft)
Thermal output (maximum operating)
700 W/hr
Acoustic emissions
LWad: 6.08 Bels
Light-load configuration
(operating at room temperature)
LWad: 6.03 Bels
(Idle at room temperature)
Table 22 Power Supply Specifications / 500 W Non-hot-plug
Item
Description
Dimensions (H x W x D)
40.00 mm x 86.00 mm x 280.00 mm (1.57 in x 3.39 in x
11.02 in)
Weight (approximate)
1.36kg (3.00 lb)
Input requirements:
Rated input voltage
100 VAC to 240 VAC
Normal line voltage
100 VAC to 127 VAC//200 VAC to 240 VAC
Line frequency
47–63 Hz
Rated input current
4.99 ARMS max @ 115 VAC
2.46 ARMS max @ 230 VAC
BTU rating
N/A
Power supply output power:
Rated steady state power
500 W
Maximum peak power
N/A
Temperature range:
Operating
+5°C to +50°C
Shipping
–40°C to +85°C
Relative humidity:
Operating
5% to 95% relative humidity, non-condensing
Non-operating
5% to 95% relative humidity, non-condensing
Table 23 Power Supply Specifications / 750 W Hot-plug
Item
Description
Dimensions (H x W x D)
38.48 mm x 86.36 mm x 190.5 mm (1.52 in x 3.4 in x 7.5
in)
Weight (approximate)
1.36 kg (3.00 lb)
Physical and operating specifications
113
Table 23 Power Supply Specifications / 750 W Hot-plug
Item
Description
Input requirements:
Rated input voltage
90 VAC to 264 VAC
Normal line voltage
90 VAC to 110 VAC/108 VAC to 132 VAC/180 VAC to
264 VAC
Line frequency
47–63 Hz
Rated input current
7.4 ARMS max @ 115 VAC
3.6 ARMS max @ 230 VAC
BTU rating
N/A
Power supply output power:
Rated steady state power
750 W
Maximum peak power
N/A
Temperature range:
Operating
+5°C to +50°C
Shipping
–40°C to +85°C
Relative humidity:
Operating
5% to 95% relative humidity, non-condensing
Non-operating
5% to 95% relative humidity, non-condensing
Physical and operating specifications
114
Index
drives
A
backplane, 49
AC power
cable connections, 36
power-down procedures, 33
cable management, 35
air baffle
drive bay configuration, 37
installing, 64
hard drives, 42
removing, 57
B
backplane, 49
reinstalling, 54
optical media drive, 40
E
electric shock
symbol, 32
removing, 53
battery
replacement warnings, 76
BBWC
warning, 32
environmental specifications, 114
exploded view
Mechanical Components Spare Parts List / 4 3.5, 16
reinstalling, 78, 80
Mechanical Components Spare Parts List / 8 2.5, 17
removing, 78, 79
system components / 4 3.5, 21, 74
bezel blank
system components / 8 2.5, 24
removing, 41
BIOS Setup Utility
F
accessing, 103
front panel components, 93
additional navigation keys, 104
H
menu bar, 103
BIOS software
overview, 103
C
hard drive
installing, 45
removing, 44, 46, 47
hard drive blank
cable connections, 36
removing, 45
cable management, 35
Hard drive LED indicators, 100
CSR (customer self repair), 5
hardware configuration
CSR program
BBWC, 77
part categories, 6
hard drives, 42
website, 5
memory, 64
customer self repair (CSR), 5
mgmt card, 82
D
optical media drive, 40
diagnostic tools and setup utilities
BIOS software, 103
POST, 111
Diagnostic tools and Setup Utilities
BIOS Setup Utility, 103
BIOS update, 111
drive bay configuration, 37
PCI expansion card, 67
power supply unit, 86
processor, 56
references, 30
SD reader module, 79
system battery, 76
system fan, 90
top cover, 34
Index 115
hardware configuration tools, 30
memory module
installing, 66
hardware specifications
removing, 66
I/O ports, 113
LAN controller, 113
memory modules
spare part number, 21, 24
memory, 113
processor socket, 113
mgmt card
processor support, 113
reinstalling, 83
status LED indicators, 114
removing, 82
thermal solution, 114
Hardware Specifications, 113
N
non hot plug hard drive
chipset, 113
default media storage, 113
installing, 48
non-hot-plug PSU
Hardware monitoring device, 113
reinstalling, 89
I/O subsystem, 113
removing, 87
optical media storage, 113
hazardous conditions. See symbols on equipment
hazardous energy circuits
O
onboard controllers
LAN, 113
symbol, 32
heat sink
installing, 63
removing, 57
hot surface
symbol, 32
warning, 32
hot-plug PSU
reinstalling, 86
removing, 86
HP
authorized reseller, 28
contact information, 28
technical support, 28
technical support requirements, 28
I
improper airflow
caution, 32
L
storage controller, 113
optical carrier
installing, 41
optical drive
activity indicator, 99
P
PCI cage
reinstalling, 74
removing, 70
PCI expansion board
installing, 73
PCI riser card expansion slot, 69
PCIe riser card
installing, 72
removing, 71
PCIe/PCI-X riser cards
installing, 70
physical dimensions, 114
server, 114
LAN controller, 113
LED indicator
system board LED, 102
LED indicators
LAN, 101
optical drive activity, 99
system board, 114
power supply unit. See PSU
Power-On Self Test
POST error indicators, 112
POST related troubleshooting, 112
processor
M
applying thermal grease compound, 61
mechanical components / 4 3.5, 16
installing, 60
mechanical components / 8 2.5, 17
removing, 59
Index 116
reinstalling, 85
processor socket
spare part number, 21, 24
specification, 113
processors
spare part number, 22, 25
PSU
system components / 4 3.5, 21
system components / 8 2.5, 24
system cover
top cover, 34
replacement warnings, 89
system fan
R
installing, 91
rear panel components, 95
S
SATA hard drives with carriers
spare part number, 25
SATA/SAS hard drives with carriers
spare part number, 22
removing, 91
system fans
spare part number, 23, 26
system LEDs. See status LEDs
system structure
front panel, 93
server dimensions
rear panel, 95
rack, 114
server warnings and cautions, 32
specifications
physical and operating, 113
storage controller, 113
system board, 96
T
thermal solution, 114
top cover
reinstalling, 34
symbols on equipment, 32
removing, 34
system battery
replacing, 76
system board
components, 96
dimensions, 114
LED, 102
W
warnings
battery replacement, 76
PSU replacement, 89
warranty, 5
platform, 114
Index 117