Canon Elan 7 NE 33V Specifications

EF16-35mm f/4L IS USM
C
Y
P
O
ENG
Instructions
Thank you for purchasing a Canon product.
Canon’s EF16-35mm f/4L IS USM is a highperformance ultra-wide angle zoom lens, for use
with EOS cameras. The lens is installed with an
Image Stabilizer.
●● “IS” stands for Image Stabilizer.
●● “USM” stands for Ultrasonic Motor.
Features
Y
P
O
1. Equipped with an Image Stabilizer that provides
an image stabilization effect equivalent to a
shutter speed 4 stops* faster (at 35 mm, when
used with the EOS-1D X).
This function provides optimal image
stabilization depending on shooting conditions
(such as shooting still subjects and following
shots).
2. Use of UD and aspherical lens elements giving
superior definition.
3. Using a fluorine coating on the foremost and
rearmost lens surfaces allows adhered dirt to be
removed more easily than before.
C
4. Ultrasonic motor (USM) for fast, quiet autofocus.
5. Manual focusing is available after the subject
comes into focus in autofocus mode (ONE
SHOT AF).
6. Circular aperture for producing beautiful
softfocus images.
7. Tight seal structure ensures excellent dustproof
and drip-proof performance.
yy Since the front element of this lens moves when
zooming, you need to attach a Canon PROTECT
filter sold separately for adequate dust-and waterresistant performance. Without a filter, the lens is
not dust or water resistant.
* Image stabilization performance based on CIPA
(Camera & Imaging Products Association) Standards.
ENG-1
Safety Precautions
Safety Precautions
Handling Cautions
●● If the lens is taken from a cold environment into a
warm one, condensation may develop on the lens
surface and internal parts. To prevent condensation
in this case, first put the lens into an airtight plastic bag
before taking it from a cold to warm environment. Then
take out the lens after it has warmed gradually. Do the
same when taking the lens from a warm environment
into a cold one.
●● Do not leave the lens in excessive heat such as in a car
in direct sunlight. High temperatures can cause the
lens to malfunction.
C
●● Do not look at the sun or a bright light source
through the lens or camera. Doing so could result in
loss of vision. Looking at the sun directly through the
lens is especially hazardous.
●● Whether it is attached to the camera or not, do not
leave the lens under the sun without the lens cap
attached. This is to prevent the lens from concentrating
the sun’s rays, which could cause a fire.
Y
P
O
Conventions used in this instruction
Warning to prevent lens or camera malfunction
or damage.
Supplementary notes on using the lens and
taking pictures.
ENG-2
Safety Precautions
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Do not make any changes or modifications to the equipment
unless otherwise specified in the instructions. If such
changes or modifications should be made, you could be
required to stop operation of the equipment.
This equipment has been tested and found to comply with
the limits for a class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
C
CAN ICES-3 (B) / NMB-3 (B)
Y
P
O
ENG-3
Nomenclature
Focus mode switch (→ 6)
Distance scale (→ 7)
Hood mount (→ 10)
Y
P
O
Zoom ring (→ 6)
Filter Mounting Thread
(→ 11)
C
Rubber ring (→ 5)
Contacts (→ 5)
Focusing ring (→ 6)
Image stabilizer switch (→ 8)
Lens mount index (→ 5)
●● For detailed information, reference page numbers are provided in parentheses (→ **).
ENG-4
1. Mounting and Detaching the Lens
See your camera’s instructions for details on
mounting and detaching the lens.
The lens mount has a rubber ring for enhanced
dust- and water-resistance. The rubber ring may
cause slight abrasions around the camera’s lens
mount, but this will not cause any problems. If the
rubber ring becomes worn, it is replaceable by a
Canon Service Center at cost.
Y
P
O
●● After detaching the lens, place the lens with
the rear end up to prevent the lens surface and
contacts from getting scratched.
●● If the contacts get soiled, scratched, or have
fingerprints on them, corrosion or faulty
connections can result. The camera and lens
may not operate properly.
●● If the contacts get soiled or have fingerprints on
them, clean them with a soft cloth.
●● If you remove the lens, cover it with the dust
cap. To attach it properly, align the lens mount
index and the  index of the dust cap as shown
in the diagram, and turn clockwise. To remove it,
reverse the order.
C
ENG-5
2. Setting the Focus Mode
Y
P
O
To shoot in autofocus (AF) mode, set the focus
mode switch to AF.
To shoot in manual focus (MF) mode, set the
focus mode switch to MF, and focus by turning
the focusing ring.
The focusing ring always works, regardless of
the focus mode.
C
3. Zooming
To zoom, rotate the zoom ring.
Be sure to finish zooming before focusing. Zooming
after focusing can affect the focus.
After autofocusing in ONE SHOT AF mode, focus
manually by pressing the shutter button halfway
and turning the focusing ring. (Full-time manual
focus)
ENG-6
4. Infinity Compensation
Mark
5. Infrared Index
Infinity compensation
mark
Distance index
Y
P
O
To compensate for shifting of the infinity focus
point that results from changes in temperature.
The infinity position at normal temperature is the
point at which the vertical line of the distance
scale L mark is aligned with the distance index.
C
For accurate manual focusing of subjects at infinity,
look through the viewfinder or look at the magnified
image* on the LCD screen while rotating the
focusing ring.
* For cameras with Live View shooting capability.
The infrared index corrects the focus setting
when using monochrome infrared film. Focus on
the subject manually, then adjust the distance
setting by moving the focusing ring to the
corresponding infrared index mark.
Some EOS cameras cannot use infrared film. See
the instructions for your EOS camera.
●● The infrared index position is based on a
wavelength of 800 nm.
●● The compensation amount differs depending on
the focal length. Use the indicated focal length
as a guide when setting the compensation
amount.
●● Be sure to observe the manufacturer’s
instructions when using infrared film.
●● Use a red filter when you take the picture.
ENG-7
6. Image Stabilizer
You can use the image stabilizer in AF or MF mode.
This function provides optimal image stabilization depending on
shooting conditions (such as shooting still subjects and following
shots).
1 Set the STABILIZER
switch to ON.
●● If you are not going to use the
image stabilizer function, set
the switch to OFF.
C
Y
P
O
2When you press the
shutter button halfway, the
Image Stabilizer will start
operating.
●● Make sure the image in the
viewfinder is stable, then
press the shutter button the
rest of the way down to take
the picture.
ON
OFF
The image stabilizer in this lens is
effective for hand-held shots under the
following conditions.
●● In semi-darkened areas such as
indoors or outdoors at night.
●● In locations where flash
photography is prohibited, such as
art museums and theater stages.
●● In situations where your footing is
uncertain.
●● When panning subjects in motion.
●● In situations where fast shutter
settings cannot be used.
ENG-8
Image Stabilizer
●● The Image Stabilizer cannot compensate for a
blurred shot caused by a subject that moved.
●● Set the STABILIZER switch to OFF when you
are taking pictures using the Bulb setting (long
exposures). If the STABILIZER switch is set to
ON, the image stabilizer function may introduce
errors.
●● The Image Stabilizer may not be fully effective
if you shoot from a violently shaking vehicle or
other transportation.
●● The Image Stabilizer consumes more power than
normal shooting, resulting in fewer shots and a
shorter movie shooting time.
●● The image stabilizer operates for about two
seconds even when your finger is off the
shutter button. Do not remove the lens while
the stabilizer is in operation. This will cause a
malfunction.
●● With the EOS-1V/HS, 3, ELAN 7E/ELAN
7/30/33, ELAN 7NE/ELAN 7N/30V/33V, ELAN
II/ELAN IIE/50/50E, REBEL 2000/300, IX, and
D30, the Image Stabilizer will not work during
self-timer operation.
C
●● When shooting a still subject, it compensates for
camera shake in all directions.
●● It compensates for vertical camera shake during
following shots in a horizontal direction, and
compensates for horizontal camera shake during
following shots in a vertical direction.
●● When you use a tripod, the Image Stabilizer
should be turned off to save battery power.
●● The stabilizer is equally effective for handheld photography and photography with a
monopod. The Image Stabilizer effect may be
reduced, however, depending on the shooting
environment.
●● The image stabilizer function also operates when
the lens is used with an Extension Tube EF12 ll
or EF25 ll.
●● Pictures may look distorted after being taken
depending on the camera, but this doesn’t affect
shooting.
●● If you set the camera’s Custom Function to
change the assigned button to operate the AF,
the Image Stabilizer will operate when you press
the newly assigned AF button.
Y
P
O
ENG-9
7. Hood
The EW-82 hood cuts out unwanted light and protects the front of the lens from rain, snow, and
dust.
Y
P
O
Button
●Attaching
To attach the hood, align the hood’s attachment
position mark with the red dot on the front of the
lens, then turn the hood as shown by the arrow
until the lens’ red dot is aligned with the hood’s
stop position mark.
C
●Removing
To remove the hood, hold down the button on
the side and turn the hood in the direction of the
arrow until the position mark on the hood aligns
with the red dot. The hood can be reversemounted on the lens for storage.
●● If the hood is not attached properly, vignetting (darkening of the perimeter of the picture) may occur.
●● When attaching or detaching the hood, grasp the base of the hood to turn it. To prevent deformation, do not
grasp the rim of the hood to turn it.
ENG-10
8. F
ilters
(Sold separately)
10. E
xtension Tubes
(Sold separately)
You can attach filters to the filter mounting
thread on the front of the lens.
Y
P
O
●● To ensure dust- and water-resistant performance,
attach a Canon PROTECT filter (77mm).
●● Only one filter may be attached.
●● If you need a polarizing filter, use the Canon
Circular Polarizing Filter PL-C B (77 mm).
●● To adjust the polarizing filter, first remove the
lens hood.
9. C
lose-up Lenses
(Sold separately)
C
You can attach extension tube EF12 II or EF25
II for magnified shots. The shooting distance
and magnification are shown below.
Focusing Distance Range (mm)
Magnification (×)
Close distance Long distance Close distance Long distance
EF12 II
EF25 II
16mm
35mm
Incompatible
206
16mm
35mm
253
0.63
0.36
Incompatible
200
216
1.12
0.80
MF mode is recommended for accurate focusing.
Attaching a 500D (77mm) Close-up Lens
enables close-up photography.
Compatibility with Close-up Lenses is as follows.
●● Can be used at the 35mm end (magnification
0.07x - 0.28x)
●● Close-up Lens 250D cannot be attached
because there is no size that fits the lens.
●● MF mode is recommended for accurate focusing.
ENG-11
Specifications
Focal Length/Aperture
16-35mm f/4
Lens Construction
12 groups, 16 elements
Minimum Aperture
f/22
Angle of View
Diagonal: 108° 10′ – 63°, Vertical: 74° 10′ – 38°, Horizontal: 98° – 54°
Min. Focusing Distance
0.28 m/0.92 ft.
Max. Magnification
0.23x (at 35mm)
Field of View
Approx. 222 x 343 – 105 x 157 mm/
8.74 x 13.50 – 4.13 x 6.18 inch (at 0.28 m/0.92 ft.)
Filter Diameter
77 mm/3.03 inch
Max. Diameter and Length
82.6 x 112.8 mm/3.25 x 4.44 inch
Weight
Approx. 615 g/21.7 oz.
Hood
EW-82
Lens Cap
E-77 II
Case
LP1219
C
Y
P
O
●● The lens length is measured from the mount surface to the front end of the lens. Add 24.2 mm
when including the lens cap and dust cap.
●● The size and weight listed are for the lens only, except as indicated.
●● Extenders cannot be used with this lens.
●● Aperture settings are specified on the camera.
●● All data listed is measured according to Canon standards.
●● Product specifications and appearance are subject to change without notice.
ENG-12
C
CT1-8597-000
0414Ni
Y
P
O
© CANON INC. 2014