blueLOGiC® hands-free kit
BT-VW01
for VW RNS510 and Skoda Columbus navigation
systems, VW RCD510 radio systems
or vehicles with FIS display
Bluetooth®-hands-free phone kit fully integrated in the vehicle infotainment
Version 13.09.2010
Contents
1. Prior to installation
1.1.
1.2.
Delivery contents
Checking the compatibility of vehicle and accessories
2. Installation
2.1.
2.2.
2.3.
Place of installation
Removal of head unit and connections
Activation of the interface
3. Interface operation
3.1.
3.2.
3.3.
3.4.
3.4.1.
3.4.2.
3.4.3.
3.4.4.
3.4.5.
3.4.6.
3.4.7.
3.4.8.
3.5.
Pairing the blueLOGiC® interface with a mobile phone
Loading of phone book
Phone functions through head-unit
Phone and additional functions through steering-wheel and FIS
Phone book
Direct dial
SMS - reading and writing
A2DP - audio streaming
MFA+ - vehicle information
MFA PDC - distance information of the park distance control
Settings - of the blueLOGiC® interface
Version - of the blueLOGIC® interface
Setup, factory defaults and update function through call codes
4. Specifications
5. Technical support
Information
page
2
Changes of the vehicle software can cause malfunctions of the interface. We offer free
software-updates for interfaces for one year after purchase. To receive a free update, the
interface must be sent in at own cost. Labor cost for and other expenses involved with the
software-updates will not be refunded.
Version 13.09.2010
BT-VW01
Product features













Integration in and controls through the telephone port of the factory infotainment
Updatable Parrot chipset with best audio quality and high phone compatibility
Automatic radio mute
Caller audio through vehicle sound-system
External microphone with amplification adjustment through infotainment
A2DP audio streaming (requirement: MFA-display in vehicle; mobile phone supports
function).
up to 10 mobile phones can be paired simultaneously
Use of factory/vehicle buttons to control phone functions
Mobile phone book integration (about 1000 call numbers)
Audio adjustment and settings through vehicle infotainment
SMS reading and writing if supported by mobile phone
Multi-language support of FIS display and automatic vehicle language detection
MFA+ display features (requirement is an FIS display)
1. Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for installation. The
place of installation must be free of moisture and away from heat sources.
1.1.
Delivery contents
HW ________ SW ________
page
3
Take down the SW-version and HW-version of the interface and store this manual
for support purposes.
Version 13.09.2010
BT-VW01
1.2.
Checking the compatibility of vehicle and accessories
Requirements
Vehicle
VW, Skoda, Seat
Navigation
RCD510 radio system
RNS510 navigation system
Columbus navigation system
Trinax Navigationssystem
Other navigation-/radio systems with FIS display
Limitations
Factory telephone kit
must be removed if installed
FIS
must be red colored (white is not supported yet)
A2DP
Only works on vehicles with MFA-display in the
instruments
2. Installation
Switch off ignition and disconnect the vehicle’s battery! The interface needs a
permanent 12V source. If according to factory rules disconnecting the battery
is to be avoided, it is usually sufficient to put the vehicle is sleep-mode. In
case the sleep-mode does not show success, disconnect the battery with a
resistor lead.
If power source is not taken directly from the battery, the connection has to be
checked for being start-up proven and permanent.
2.1.
Place of installation
The interface is installed on the backside of the navigation/radio unit which must be
removed for installation of the interface.
2.2.
Removal of head unit and connections
page
4
Unlock the navigation/radio unit and remove it from the
dashboard.
Version 13.09.2010
BT-VW01
Remove the vehicle harness‘ Quadlock socket from the
head unit. Plug the Quadlock socket of the interface harness
into the head unit and the Quadlock socket of the vehicle
harness into the Quadlock connector of the interface harness.
Quadlock socket
Install the microphone close to the driver. Connect the microphones 3 Pin AMP jack to the 3
Pin AMP jack bush of the blueLOGiC® harness.
2.3.
Activation of the interface
After first installation the vehicle must go into sleep-mode in order to recognize the newly
attached hardware. After re-connecting the battery, lock the vehicle and wait for 5 -10
minutes.
3. Interface operation
On vehicles with RCD510 orRNS510 the head-unit’s phone menu can be used to control the
blueLOGiC® interface. On vehicles with FIS display, it is possible to control the blueLOGiC®
interface through the steering-wheel buttons and the FIS’ phone menu. If a vehicle is
equiped with head-unit and FIS, both controlling options are available. Controls by FIS is
offering more options in comparison to controls by head-unit. Some settings can be changed
by dialing setting codes which is especially needed in vehicles with retrofitted
RCD510/RNS510 without FIS display.
3.1.
Pairing the blueLOGiC® interface with a mobile phone
Version 13.09.2010
BT-VW01
page
If a mobile phone had been paired to the blueLOGiC® interface (reqirement is an occurred
pairing with a mobile phone, see above), a connection will be automatically established as
soon as the mobile phone is in reach. If multiple paired mobile phones are simultaneously in
reach, the blueLOGiC® interface will be connected to the first phone.
5
Up to 10 mobile phones can simultaneously be paired with the blueLOGiC® interface. If a
11th phone is paired, the oldest entry is automatically deleted. In some cases, it becomes
necessary to put the vehicle in sleep mode to enable correct function of the 11th phone.
For pairing, enable the pairing mode of the mobile phone (see manual of the mobile phone).
Search with the mobile phone for „blueLOGiC“ or „CK5050N“ and connect with activation
code „1234“.Some mobile phones try to connect to the blueLOGiC ® interface with another
function as "hands free". Check this attitude and switch the adjustment to "hands free" if
necessary (see manual of the mobile phone).
If you have connection problems between mobile phone and the blueLOGIC, first check at
the parrot website whether an update for the parrot chip is available. The part number of
the parrot chip can be found in the specifications at the end of the manual.
3.2.
Loading of phone book
After each establishment of connection to the mobile phone, the phone book of the mobile
phone will be loaded to the vehicle infotainment.
Depending on the mobile phone either it will be loaded from the phone’s memory or the
SIM card. This process can take a few minutes. If the phone book is no or not completely
loaded, it might be necessary to copy the contacts from the SIM-card to the mobile phone
memory!
Some mobile phones do not automatically load the phone book to the infotainment, but the
sending must be manually initiated (the procedure varies depending on the mobile phone,
z.B. “send phone book to Bluetooth”).
The manual procedure must be repeated for refreshment if the mobile phone’s contacts
have been edited.
The memory of blueLOGiC® interface can save about 1000 call numbers.
Phone functions through head-unit
The interface enables the phone bus of the factory
navigation system. Therefore in principal, the operation
through the head-unit is analogue as described in the
manual of the navigation/radio system.
3.4.
RNS510
Phone and additional functions through steering-wheel and FIS
Using the menu button
of the steering-wheel,
the FIS display switches
through different
menus (radio, nav,
phone,…). With
installed blueLOGIC®,
the phone menu
shows the blueLOGIC®
startup screen.
The mobile phone’s
signal strength is
shown by the bars on
top of the startup
screen. The
blueLOGIC® main
menu is opened by
up or down key of
the steering-wheel
while the startup
screen is displayed.
6
3.3.
Version 13.09.2010
page
The options of the blueLOGIC® main menu at FIS are described
in the chapters 3.3.1. thru 3.3.8..
BT-VW01
3.4.1. Phone book
The phone book
entries of the
connected phone are
available in the
phone book menu.
Contacts are
displayed once for
every
phone number in a
fixedorder (office,
mobile, home,…).
Once an entry is
selected, it will be in
single display with
dialing option.
3.4.2. Direct dial
The mobile phone’s direct dial
numbers are available in the menu
items direct dial.
3.4.3. SMS - reading and writing
If supported by the mobile phone, the blueLOGIC® interface supports reading and writing
SMS under menu item SMS (if supported by mobile phone). There are some standard
template answers available.
3.4.4. A2DP - audio streaming
When the blueLOGiC® interface AD2P function is started, it is
possible to listen to music files which are played by the mobile
phone on the factory sound system. The available options to control
the play functions of the mobile phone depend very much on the
mobile phone, for example iPhones® do not support any track
skipping. Full functions are starting and stopping the playback, next
track and previous track. The functions can be executed by selecting
the corresponding menu entry. Playback is automatically stopped
during call activity but possibly needs to be manually restarted
(depend on mobile phone).
Note: A2DP only works on vehicles with MFA-display in the
instruments
3.4.5. MFA+ - vehicle information
page
7
The MFA+ function shows additional
detailed condition information.
Version 13.09.2010
BT-VW01
3.4.6. MFA PDC - distance information of park distance control
This function shows the
distance data of the
factory PDC.
Upper 4 values =
front sensors
Lower 4 values =
rear sensors
3.4.7. Settings - of the blueLOGiC® interface
In the settings menu it is possible to make
volume adjustments, manually adjust the
language, change unit scales and load the
interface’s factory values.0
3.4.8. Version of the blueLOGiC® interface
Show blueLOGiC® interface version
information.
3.5.
Setup, factory defaults and update function through call codes
Settings of the blueLOGiC® interface can also be changed by dialing setting codes in the
vehicle telephone mode. Caller audio volume, Ringing tone volume and microphone
sensitivity can be adjusted separately. The interface can be reset to factory defaults and
updates of the Parrot chipset can be initiated. To execute a function, just dial the
corresponding code from the below table like a phone number and confirm with “pick-up”.
Code no.
+001xx
+0021xx
+0022xx
+009
+000
Min
01
01
01
Max
15
15
15
page
8
Function
Microphone sensitivity
Caller audio volume
Ringing tone volume
Factory defaults
Parrot Update Mode
Version 13.09.2010
BT-VW01
To the codes for volume and sensitivity it is necessary to add two digits for the desired value
(01 min. to 15 max.). For example dial “+002112” to set the caller audio volume to level 12.
After dialing a code, the navigation will confirm with “call failed”.
System updates of the Parrot chipset are possible through Bluetooth® via PC.
4. Specifications
Integrated Bluetooth® Chip
Operation voltage
Stand-by power drain
Operation power drain
Power consumption
Temperature range
Weight
Dimensions (box only) B x H x T
Parrot CK5050new
10.5 – 14.8V DC
<1mA
120mA
1.8W
-30°C to +80°C
95g
106 x 30 x 71 mm
5. Technical Support
Caraudio-Systems Vertriebs GmbH
manufacturer/distribution
Rheinhorststr. 22
D-67071 Ludwigshafen am Rhein
NavLinkz GmbH
corporate sales/tech support
Eurotec-Ring 45
D-47445 Moers
phone +49 180 3 907050
email support@caraudio-systems.de
page
9
Legal disclaimer: Mentioned company- and trademarks, as well as product names/codes are registered
trademarks ® of their corresponding legal owners.
Version 13.09.2010
BT-VW01