CMS1002W
INTRODUCTION
This manual is intended as a reference for the
installation of a Scotsman ice maker model
CMS1002.
TABLE OF CONTENTS
Page
Specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Environmental Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
For the Installer
Machine & Bin Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
For the Plumber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
For the Electrician
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Final Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Initial Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Component Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Service Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Service Diagnosis
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
September, 1993
Page 1
CMS1002W
SPECIFICATIONS
Always refer to the nameplate, located on the back
of the cabinet, for the:
• model number,
• serial number,
• basic electrical
requirements,
• minimum circuit ampacity,
• maximum fuse size,
• and refrigerant charge.
A serial number plate with the model number,
serial number and refrigerant charge is located
behind the front panel, near the control box.
The unit comes from the factory with the correct
refrigerant charge. The refrigerant charge
information is for recharging, should that be
necessary.
All utility connections are made at the back of the
ice maker.
Before beginning installation, be sure that all of the
components necessary for complete assembly of
the ice system are available, and are the correct
components with regard to model, voltage, and
finish.
A stacking kit (KSCMS) is required for stacking
CMS1002 ice machines. It interconnects the sonar
bin ice level controls. CMS1002 may only be
stacked onto another CMS1002.
The CMS1002 will fit any 30" wide Scotsman bin
without needing a bin top. Other bins will require a
bin top.
Model Number
Dimensions
x D" x H"
CMS1002WE-32A
CMS1002WE-3A
W"
Basic Electrical
Refrigerant Type
Refrigerant Charge*
30 x 24 x 27
208-230/60/1
R-22
55 ounces
30 x 24 x 27
208-230/60/3
R-22
55 ounces
* The system charge is in the machine. This number is for recharging purposes only. If the nameplate has a
different value, go by the nameplate.
Minimum
Maximum
Air Temperature
Water Temperature
Voltage
500 F.
400 F.
-5%
0
100 F.
0
100 F.
September, 1993
Page 2
+10%
CMS1002W
FOR THE INSTALLER: Environmental Limitations
Installation Limitations
Water Limitations
The ice making portion of this ice system is
designed to be installed indoors, in a controlled
environment.
An ice machine is a food manufacturing plant; it
takes a raw material, water, and turns it into a food
product, ice. The purity of the water is very
important in obtaining pure ice and in maximizing
product life. These general recommendations
should help keep the ice maker clean:
Minimum
Maximum
Air Temp
0
50 F.
1000F.
Water Temp
400F.
1000F.
Water Pressure
20 PSI
80 PSI
Voltage
197
253
Operating the ice machine outside of the above
limitations, or outdoors, is potentially damaging to
the machine; also it is misuse of the machine,
which may void the warranty.
Scotsman Ice Systems are designed and
manufactured with the highest regard for safety
and performance. They meet or exceed the
standards of UL, NSF, and CSA.
Scotsman assumes no liability or responsibility of
any kind for products manufactured by Scotsman
that have been altered in any way, including the
use of any part and/or other components not
specifically approved by Scotsman.
1. Filter the water used to produce ice. Water filters
vary greatly in ability and function. Install one that
filters out suspended solids to a dimension of 5
microns or smaller. The finer the filter the better,
but finer filters will clog sooner than course ones. It
may be necessary to add a course filter ahead of
the fine filter to prolong filter life.
2. Check with a water treatment specialist for a
water test, and recommendations regarding filters
and treatment.
Service Limitations
Some space on the sides, the back and the top
should be allowed for service and utility
connections.
Scotsman reserves the right to make design
changes and/or improvements at any time.
Specifications and design are subject to change
without notice.
NAMEPLATE, LOCATED ON
BACK PANEL.
A SERIAL NUMBER PLATE IS
LOCATED BEHIND THE
FRONT PANEL, NEAR THE
CONTROL BOX.
September, 1993
Page 3
CMS1002W
FOR THE INSTALLER: Machine & Bin Assembly
Overview:
This ice system is comprised of 2 major
assemblies:
1. The ice storage bin.
2. The ice maker itself.
Storage Bin:
After uncrating the ice storage bin, attach the legs
to the bin:
1. Use a portion of the carton as a cushion, and tip
the storage bin on its back.
2. Screw the legs into the threaded holes in the
bottom of the bin.
3. Turn the leg levelers all the way in to prepare
the bin and ice machine for leveling.
4. Return the bin to the upright position.
Ice Maker:
1. Arrange for proper electric, water and drain.
See instructions for the plumber and for the
electrician.
2. Position the ice storage bin in the selected
location.
3. Level the bin, in both the front to rear and side
to side directions.
4. Inspect the bin top mounting gasket which
should be flat, with no wrinkles, to provide a good
water seal when the cuber is installed on top of
the bin.
5. Install the modular cuber on top of the bin using
care to be sure a good seal is made between the
two cabinets, use of a mechanical lift is
recommended. Align the holes in the bottom back
of the cabinet to mate with the two mounting straps
on the top rear of the bin.
6. Use bolts and straps found in the hardware
package to secure the ice machine to the ice
storage bin. When alignment and leveling are
completed, tighten the bolts to secure the
mounting straps.
September, 1993
Page 4
CMS1002W
FOR THE PLUMBER
Water Supply
Drain Connections:
The recommended water supply line is a 3/8-inch
O.D. tubing with a minimum operating pressure of
20 PSIG and a maximum of 80 PSIG.
Connections: All drains are gravity type and must
have a minimum of 1/4 - inch fall per foot of
horizontal run. The drains to be installed must
conform with the local plumbing codes. Install a
vertical open vent on the ice machine reservoir
drain. The ideal drain recptacle is a trapped and
vented floor drain. The storage bin drain should be
insulated.
A separate water inlet is required for the
condenser water supply.
Connect to cold water supply line with standard
plumbing fittings, with shut off valve installed in an
accessible place between the water supply and
the cuber. ln some cases a plumber will be
required.
CONFORM TO ALL LOCAL CODES
Water Cooled Connection: A separate cold water
supply is required, connect to the 3/8-inch FPT
fitting at the back of the cabinet. An additional
drain line is required to drain the water cooled
condenser, and must not interconnect to any of the
other drains.
CONDENSER INLET
HAND SHUT OFF
VALVE
RESERVOIR
DRAIN VENT
CONDENSER DRAIN
HAND SHUT
OFF VALVE
POSITION OF
FILTER
BIN DRAIN VENT
WATER COOLED PLUMBING
CONNECTIONS
FLOOR DRAIN
September, 1993
Page 5
CMS1002W
FOR THE ELECTRICIAN: Electrical Connections
See the NAMEPLATE for current requirements to
determine wire size to be used for electrical
hookup. The cuber requires a solid chassis to
chassis earth ground wire. See Wiring Diagram.
Be certain the cuber is connected to its own
electrical circuit and individually fused. Voltage
variation should not exceed ten percent of the
nameplate rating, even under starting conditions.
Low voltages can cause erratic operation and may
be responsible for serious damage to the
icemaker.
All external wiring should conform to the
national, state and local electrical code
requirements. Usually an electrical permit and
services of a licensed electrician will be
required.
Electrical connections are made at the rear of the
icemaker, inside the junction box.
The cuber is packaged with a flexible cord and
matching receptacle (not attached), use them to
make electrical connection between the icemaker
and the building’s electrical power, if allowed by
local codes.
ELECTRICAL JUNCTION BOX
FUSES or HACR
CIRCUIT BREAKERS
September, 1993
Page 6
CMS1002W
FOR THE INSTALLER: Final Check List
1. Is the ice maker cabinet in a room where
ambient temperatures are within the minimum and
maximum temperatures specified?
2. Is there clearance at both sides of the cabinet
and at the back and top for service and utility
connections?
3. Has water supply pressure been checked to
insure a minimum of 20 PSIG and a maximum of
80 PSIG operating pressure?
4. Is the cabinet level?
5. Check that any shipping material has been
removed from inside the cabinet.
6. Have all electrical and piping connections been
made?
7. Are the Master and Compressor switches on
OFF?
8. Has power been connected to the ice maker?
9. Is the water supply line shut off valve installed?
10. Check all refrigerant lines and conduit lines, to
guard against vibration or rubbing and possible
failure.
11. Have the bin and cabinet been wiped clean
and sanitized?
12. Has the Field Quality Audit form been properly
filled out? Check for correct model and serial
numbers from Serial nameplate, then mail the
completed form to the SCOTSMAN factory.
13. Has the owner been given the name and
telephone number of the authorized SCOTSMAN
Service Agency serving him?
September, 1993
Page 7
CMS1002W
INITIAL START UP
Ice Maker:
1. Remove front panel by pulling out to unsnap.
2. Remove two screws and the control box cover.
3. Remove the evaporator cover.
4. Remove the left side service panel.
5. Check that the ON/WASH/OFF rocker switch
and the Compressor ON-OFF toggle switch are in
the OFF position, on the control box.
6. OPEN the water supply line shut off valve.
7. Inside the control box is the shaft of the timer
and the switch assembly. Rotate the shaft of the
timer and switch assembly clockwise to where the
actuator arm on the microswitch drops off outer
cam into cam slot. See Timer Cam Positions.
10. Check that the water cascades down over
each cube mold and into the reservoir.
11. When the reservoir is full, move the
compressor ON-OFF switch, to the ON position.
TIMER CAM POSITIONS
ACTUATOR
9. Observe water fill cycle: Water pump operates
and water inlet solenoid valve OPENS, incoming
water flows from the valve through the tubing, the
reservoir fills and excess water drains out the
machine drain. At the end of the harvest cycle, the
water inlet solenoid valve will close and the water
fill cycle is complete. If the reservoir is not full,
advance the shaft of the timer clockwise into a new
harvest cycle; this opens the water valve again.
The water pump forces water from the reservoir up
to the water distributor at the top of each
evaporator plate, where water is uniformly
dispensed, cascades down both sides of the
evaporator plate and drains back into the reservoir
for recirculation.
12. Check operation of the freezing cycle: The
compressor is operating.The icemaking process
begins; feeling the metal parts of the evaporator
plate reveals cold temperature, very shortly ice
begins to form. Tubing will become frosted at the
top of the evaporator plate. Freezing time will
range between 13 and 15 minutes. Longer time for
temperatures above 70 degrees F. and shorter
time required when temperatures are below
70-degrees F. Average complete cycle time is
about 16 minutes.
MICROSWITCH
CAM &
SHAFT
13. Warm water should begin to flow from the
condenser drain.
HARVEST
PORTION
Note: To optimize the balance between ice
production and water use, the water cooled
discharge pressure must be 220 P.S.I.G. Check
the discharge pressure and adjust the water
regulating valve to obtain 220 P.S.I.G. pressure.
FREEZE
PORTION
14. Check CUBE SIZE
8. Move the ON/WASH/OFF rocker switch to the
ON position.
The dimensions of the cubes are fixed by the size
and shape of the molds on the evaporator plate,
except that the thickness of the cube MAY need to
be adjusted at start up. There is only one size of
cube that is correct; adjusting the cube size control
to that size of cube will allow the ice maker to
produce ice at its most efficient size. The correct
size cubes will be fully formed at the edges; will
harvest off of the evaporators beginning with
individual cubes at the top of the evaporator, then
vertical strips for the balance; and will appear
similar to the illustration for “Correct Size Cube”.
September, 1993
Page 8
CMS1002W
INITIAL START UP
Adjust for the correct size if needed:
CUBES (ACTUAL SIZE)
To produce SMALLER sized ice cubes:
Locate cube size control knob, in the front of the
control box. Rotate this knob one eighth of a turn
counter clockwise. Observe size of the ice cubes
in the next ice cube harvest and adjust again if
needed, until the correct ice cube is achieved.
TOO
THICK
To produce LARGER ice cubes:
Locate cube size control on the front of the control
box. Rotate the knob one eighth of a turn
clockwise. Observe size of ice cubes in the next
cube harvest and adjust again if needed, until
correct the ice cube size is achieved.
1 1⁄4"
14. Check Harvest Time. The machine must
harvest all cubes before returning to a freeze cycle.
Increase the harvest time if there is less than 15
seconds of harvest time after the last cube has
fallen into the bin.
CORRECT
1 1⁄4"
SIZE
CUBE
Decrease the harvest time if there is much more
than 15 seconds of harvest time after the last cube
has fallen into the bin. Note: Harvest time is
dependent upon the water and air temperatures at
the ice machine. Do not adjust harvest time too
short, as this will cause a freeze up .
Note: Optimum performance will be achieved when
the ice machine is adjusted to produce this size and
shape of cube. The typical batch weight at this
setting is between 8.25 and 9 pounds.
See the next page for detailed harvest time
adjustment instructions.
15. Check ICE BIN LEVEL CONTROL
The amount of ice maintained in the bin is
adjustable. The normal setting is “full”. If the
operator desires, the level of ice in the bin may be
adjusted lower to shut off the machine when the
bin is only partially full.
TOO
THIN
To Test The Ice Level Setting:
1. Open the bin door and locate on the bottom of
the ice machine, the ice level sensor. It’s in a
socket about 2" in diameter and located left of the
evaporator plates.
Adjust Bin Ice Level
2. When the machine is running, wait untIl near the
end of a “harvest” cycle.
3. Replace front panel.
3. Hold a flat object about the size of this service
manual over the ice level sensor socket.
4. The ice machine should turn off at the end of the
harvest cycle.
5. Slowly lower the flat object straight down.
6. The ice machine will start again at the point
where it will maintain the ice level.
1. Locate ice level control knob.
2. Turn knob to the desired position.
4. To test, wait until the ice machine is near the
end of a “harvest” cycle, if there is ice in the bin
higher than the position the ice level control is set
for, the ice machine will turn OFF at the end of the
harvest cycle. If no ice in the bin, test again as
described under, “To Test The Ice Level Setting”.
16. Replace all panels, the machine is ready for
automatic operation.
September, 1993
Page 9
CMS1002W
ADJUSTMENT OF THE TIMER & SWITCH ASSEMBLY
One complete revolution of the cam on the timer
represents eight minutes. If left as factory set,
four and one-half minutes comprise the freezing
cycle portion during cam rotation, and the final
three and one-half minutes is the defrost/harvest
cycle. Rotating the shaft of the timer cam
Clockwise will put the ice machine into the freeze
or harvest cycle, as required in the cleaning
instructions.
/////////////////////////////WARNING/////////////////////////////////
Disconnect electrical power supply to icemaker
whenever adjustment procedures are performed.
TIMER CAM POSITIONS
ACTUATOR
MICROSWITCH
CAM &
SHAFT
/////////////////////////////////////////////////////////////////////////////
To adjust the timer & switch assembly:
HARVEST
PORTION
1. Remove front panel.
2. Remove control box cover.
A. To start the HARVEST CYCLE: Slowly rotate
the shaft of the timer and switch assembly,
clockwise until the actuator arm on the
microswitch initiates the harvest cycle. An audible
click can be heard, but in a noisy area, look at
the cam and switch to observe the event
FREEZE
PORTION
B. To start the FREEZING CYCLE: Slowly rotate
the shaft of the timer and switch assembly
clockwise until the actuator arm on the microswitch
initiates the freezing cycle.
TIMER ADJUSTMENT
C. To adjust the length of the harvest cycle:
1. Loosen the adjustment screw on the cam and
rotate the shaft of the cam to move the cam. More
of a gap between the high and low portions will
yield more harvest time.
MICROSWITCH
SHAFT OF
CAM
2. Tighten the set screw.
3. Replace the control box cover and front panel.
lt is important that the length of the harvest cycle
allow enough time for all the ice cubes to fall from
the evaporator. Too short of a time will cause the
evaporator to freeze up and stop ejecting ice into
the bin. Too much time wastes icemaking capacity,
energy and water. Adjustment of the harvest cycle
may require an adjustment of the cube size
control.
SET SCREW
September, 1993
Page 10
CMS1002W
COMPONENT DESCRIPTION
Compressor Contactor
Hot Gas Solenoid Valve
The compressor contactor carries the compressor
line current. The contactor is wired so any control
in the pilot circuit, such as the bin control, and high
pressure controls, etc., will cause the contactor
holding coil to be de energized, when the control
contact OPENS, thereby breaking the circuit to the
compressor.
The hot gas solenoid valve opens only during the
harvest cycle. When it opens, it diverts the hot
discharge gases so that they flow directly into the
evaporator plates, by-passing the condenser and
thermostatic expansion valve. The hot gases warm
the evaporators, releasing the ice cubes from the
ice cube molds. The hot gas solenoid valve is
installed in a branch of the discharge line, and
when the timer switches the ice machine into the
harvest cycle, the energized solenoid coil lifts the
valve stem within the valve body, allowing the hot
discharge gas to be diverted to the evaporators.
Cube Size Control
This reverse acting (closes on temperature fall)
thermostat determines how long the freezing cycle
will be. The cube size control closes it’s contacts
when the evaporator cools to the set temperature,
starting the timer. A variation in heat load (either
ambient air or incoming water temperature) will
affect the efficiency of the refrigeration system, and
that will vary the length of time it takes the
evaporators to cool to the temperature at which the
cube size control is set to close, which, in turn, will
affect the overall cycle time. See CUBE SIZE
ADJUSTMENT BEFORE attempting to adJust the
control.
High Temperature Cut Out
This temperature sensor is located next to the hot
gas valve, on the outlet side.
During normal operation, it does not affect the ice
machine, but it will shut the machine off if the hot
gas line overheats. It is an automatic reset.
Relay
The multi-function, three pole, double throw, relay
plugs into a socket on the printed circuit board in
the control box. The relay functions in part to
by-pass the bin control during the harvest and
freeze cycles, preventing the icemaker from
shutting off in the middle of a cycle. The bypass
action allows only complete freeze and harvest
cycles; the only time that the ice maker can shut
off on bin control is as the end of the harvest cycle.
Timer - Timer & Switch Assembly
The timer begins to turn when activated by the
cube size control. The outer surface, or large
diameter lobe of the timer cam, determines the
length of time for finish freezing of the ice cubes,
while the inner surface, or small diameter lobe,
determines length of the harvest cycle. The
single-pole, double throw microswitch on the timer
controls the power to the plug in relay coil, making
it either the freezing or harvest cycle. The
microswitch is actuated by a cam assembly
directly connected to the timer motor. The timer
cam can be adjusted to vary the defrost time, as
required. One complete rotation of the cam will
take eight minutes. Harvest is preset at 2 and one
quarter minutes.
September, 1993
Page 11
CMS1002W
COMPONENT DESCRIPTION
Ice Level Control
This electronic control uses sound waves to
measure the distance between the bottom of the
ice machine and the top of the ice in the bin. It is
designed to control the machine’s ice production to
maintain that distance.
The control is adjustable so that the ice machine
will maintain a certain height of ice. It will not fill
any closer to the ice machine than 8", and will not
work if the distance to the bottom of the bin is
greater than 8 feet.
Because it uses sound waves, a slight “ticking”
sound can be heard coming from the bottom of the
machine.
ON/OFF/WASH SWITCH
ICE LEVEL
SELECTOR
SWITCH
THE AMOUNT OF
ICE MAINTAINED
IN THE BIN CAN
BE SELECTED BY
THE USER
FULL
PARTIAL
September, 1993
Page 12
CMS1002W
COMPONENT DESCRIPTION
Electric Water Inlet Valve
Reservoir
The water inlet solenoid valve fills the reservoir
assembly with water. Excess water overflows out
the overflow standpipe located at the back of the
reservoir. This action fills and rinses the reservoir
during each harvest cycle. The flow rate is .75
g.p.m.
The reservoir, located below the evaporators,
stores the inlet water charge, and collects the
water that flows over the evaporator plates. Above
the reservoir, but below the evaporators are the
cube chutes, designed to retain any water splash
from ice making or harvest. Most ice will be falling
into the bin below the center evaporator.
Water Distribution System
The water distribution system evenly supplies
water to all cells of the evaporator plates. The
water pump pumps water from the reservoir up the
vertical tygon tube to the tee. From there water is
channeled through the water manifold to the water
distributors, above each evaporator plate, and
from six holes within each distributor, water flows
to the cells of each side of the evaporator plates.
Gravity flow returns the unfrozen excess portion of
water to the reservoir for recirculation.
Strainer
A water strainer is located in the potable inlet water
line before the water inlet solenoid valve. Clean
the water strainer as needed.
High Pressure Safety Control
This is a manual reset control that shuts down the
icemaker, should the discharge pressure ever
reach 350 PSIG.
WATER
DISTRIBUTION
SYSTEM
EVAPORATOR
WATER
REGULATING
VALVE
WATER PUMP
RESERVOIR
HIGH PRESSURE
CUT OUT
STRAINER
ELECTRIC WATER VALVE
September, 1993
Page 13
CMS1002W
SERVICE SPECIFICATIONS
When servicing a machine, it’s helpful to compare
that unit’s operating characteristics to those of a
new, clean, normally operating machine. What
follows is that type of information:
COMPONENTS
Timer: Makes one complete revolution in 8 minutes. The harvest time is factory preset at 2 1⁄4 minutes. The
harvest time is adjustable as required.
Inlet Water Valve: Opens and admits 3⁄4 gallon per minute during the harvest cycle.
Cube Size Control: Reverse acting temperature control, contacts close between 240F. and 00F.
High Pressure Safety Switch: Contacts open at 350 P.S.I.G.
Bin or Ice Level Control
Maximum Full Height
8" from the base of the ice machine.
Partial Fill Setting
21" - 22" from the base of the ice machine.
Maximum Storage Bin Interior Height
8’ from the base of the ice machine.
OPERATING CHARACTERISTICS
The values listed below are representative of
values seen at a wide range of air and water
temperatures and are for a normal cube size.
FREEZE CYCLE
Average Discharge Pressure
Suction pressure at the end of the freeze cycle
Freeze Time
220 P.S.I.G.
26-23 P.S.I.G.
13-15 minutes
HARVEST CYCLE
Average Suction Pressure
70-100 P.S.I.G.
Harvest time is assumed to be 2.25 minutes. This can be adjusted to suit local conditions.
September, 1993
Page 14
CMS1002W
CLEANING
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
A Scotsman Ice System represents a sizable investment of time and money in any company’s business. In
order to receive the best return for that investment, it MUST receive periodic maintenance.
Maintenance and Cleaning should be scheduled at a minimum of twice per year.
//////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
9. Switch the machine to “wash” and continue to
CLEANING: ICEMAKER
add fresh water to flush residual cleaner from the
///////////////////////////////WARNING/////////////////////////////
system. Switch the Wash/Off/Ice switch off.
Electrical power needs to be on when doing in
10. Sanitize the ice maker and bin, see “Sanitize
place cleaning.
Water System”.
/////////////////////////////////////////////////////////////////////////////
11. Replace the front liner.
1. Remove front panel.
12. Switch the Wash/Off/Ice switch back on.
2. Switch the Wash/Off/Ice switch to OFF.
13. Replace the front panel
3. Remove the front liner.
14. Check the next batch of cubes to make sure all
4. Remove and discard all ice from the storage bin.
of the acid taste is gone.
5. Locate the reservoir drain and drain the
/////////////////////////////////CAUTION///////////////////////////
reservoir. If the reservoir doesn’t drain completely,
DO NOT use ice produced from the cleaning
disconnect the pump hose attached to the water
solution. Be sure none remains in the bin.
distributors and place the end of the hose in a
//////////////////////////////////////////////////////////////////////////
bucket. Switch the Wash/Off/Ice switch to Wash,
and allow the pump to discharge the rest of the
15. Remove and discard all ice from the storage
water. Reattach the hose to the water distributors.
bin, pour hot water into the storage bin to melt the
6. Mix 8 ounces of Scotsman Ice Machine Cleaner
with 1 gallon of warm (950F. - 1150F.) water and
pour into the reservoir until full.
cubes and also clean out the bin drain.
16. The unit is now ready for continued automatic
operation.
7. Switch the Wash/Off/Ice switch to “wash”. Let
Scotsman Ice Machine
Cleaner contains acids.
These compounds may
cause burns.
If swallowed, DO NOT
induce vomiting. Give
large amounts of water
or milk. Call Physician
immediately. In case of
external contact, flush
with water.
KEEP OUT OF THE
REACH OF CHILDREN.
the unit operate for 30 minutes, then switch the
unit off.
8. Drain the reservoir again (repeat step 5)
Strainer:
A water strainer is located in the water line before
the inlet water solenoid valve. It is designed to
catch large particles that may be in the water. To
clean:
1. Shut off
water supply.
2. Unscrew
screen from
strainer.
3. Brush
particles from
screen
4. Replace
screen in
SCREEN
strainer.
5. Turn water
supply back
on.
September, 1993
Page 15
CMS1002W
CLEANING
taking care to wipe all surfaces that are normally in
contact with ice.
SANITIZE WATER SYSTEM
1. Remove and discard all ice from the bin.
10. Replace the evaporator cover. Replace the
front panel.
2. Remove front panel.
3. Drain the reservoir
11. Move the master switch to ON.
4. Prepare 2 gallons of an approved sanitizer
solution in accordance with the instructions on the
package, or use the following instructions for use
of household bleach, if it meets local codes:
This procedure is to be done monthly
Mix a sanitizing solution of 1 ounce of household
bleach to 2 gallons of water.
2. Switch the ice maker off.
5. Pour 1 gallon of the sanitizer into the ice maker
reservoir.
6. Move the Wash/Off/Switch switch to “Wash”,
and allow the solution to circulate for a MINIMUM
of 5 minutes.
7. Move the Wash/Off/Switch switch to “Off”.
8. Remove the drain plug and drain the reservoir.
9. Using a clean sponge and the remainder of the
sanitizer solution, wipe the interior of the
evaporator cover and the inside of the storage bin,
SANITIZE ICE STORAGE BIN
1. Remove and discard all ice from the bin.
2. Prepare 2 gallons of an approved sanitizer
solution in accordance with the instructions on the
package, or use the following instructions for use
of household bleach, if it meets local codes: Mix a
sanitizing solution of 1 ounce of household bleach
to 2 gallons of water.
3. Using clean rubber gloves and a clean cloth,
wipe all interior surfaces of the ice machine and
ice storage bin with the sanitizing solution.
Immerse any small parts in the sanitizing solution
and wash the parts, flushing the solution
thoroughly in, over and through all parts and
surfaces of the parts being cleaned.
4. Allow to air dry.
5. Switch the ice
machine back on.
RESERVOIR
DRAIN
ON/OFF/WASH
SWITCH
September, 1993
Page 16
CMS1002W
SERVICE DIAGNOSIS
SYMPTOM
POSSIBLE CAUSE
PROBABLE CORRECTION
No ice, machine does not run
1. No electrical power
1. Restore power
2. Circuit breaker tripped or fuse
blown
2. Reset breaker or replace fuse,
check for electrical fault.
3. High pressure control open.
3. Reset HPC, check fan motor for
proper operation, and condenser
coil for dirt.
4. ice level control holding machine
off
4. Check ice level control circuit.
See page 19.
5. High temp. cut out open
5. Hot gas valve leaks thru, replace
hot gas valve
6. Timer switch open
6. Replace timer
No ice, compressor does not run,
rest of ice machine does.
No ice, no water over evaporators
No ice, everything runs
Low ice production
7. Master switch open
7. Check or replace switch.
8. Circuit board open
8. Replace circuit board.
1. Open contactor coil
1. Replace contactor
2. Thermostatic Expansion valve
clogged or does not open.
2. Check/replace TXV.
1. Water pump does not pump
1. Check/replace water pump
2. No water in reservoir
2. Check/replace water inlet valve.
1. Too much heat load
1. Check for slow leak thru of water
inlet valve.
2. Low on refrigerant
2. Check pressures, if low
find/repair leak; weigh in charge.
3. Suction pressure too high
3. Defective compressor - replace
1. Too much heat load.
1. Check condenser air inlet
temperature. Check water
temperature.
2. Compressor inefficient.
2. Replace compressor
3. Non condensable gasses in
refrigeration system.
3. Check head pressure, if very
high, and no other reason is
suspected, replace refrigerant
charge.
September, 1993
Page 17
CMS1002W
SERVICE DIAGNOSIS
SYMPTOM
POSSIBLE CAUSE
PROBABLE CORRECTION
Low ice production
4. High head pressure, a result of a
dirty condenser
4. Clean water circuit of condenser
5. Hot gas valve leaks thru
5. Replace hot gas valve
6. High discharge pressure
6. If possible, reduce condenser
water inlet temperature.
1. Cube size control will not close
1. Check temp. of suction line, cube
size control will not close if temp.
too high. If temp. low enough,
replace cube size control
2. Timer motor open
2. Replace timer
3. Plug in relay contacts open
3. Replace relay
4. Not enough time during the
harvest cycle to drop all ice
4. Adjust timer for more harvest time
5. Cube size wrong
5. Adjust cube size
6. Hot gas valve restricted.
6. Replace hot gas valve.
7. Not enough water to help harvest.
7. Check for restriction of water
supply.
8. Head pressure too low
8. Check water reg./pressure
control valve. Check for low
refrigerant charge.
1. Relay coil open
1. Replace relay
2. Timer stuck in harvest cycle
2. Check for power to timer motor, if
power replace timer, if no power to
timer motor, replace relay.
3. Timer microswitch N.O. contacts
will not close.
3. Replace timer.
1. Shortage of water
1. Check for restriction of water
supply. Check for leak.
2. Evaporator water passages
restricted.
2. Clean ice maker.
3. Cube size set wrong
3. Adjust cube size control
1. Restricted sump drain
1. Repair drain
2. Inlet water valve lets in too much
water
2. Replace valve
No ice falling in bin, unit frozen up
Ice maker stuck in harvest cycle
Ice is mal-formed
Water overflows from reservoir into
bin.
September, 1993
Page 18
CMS1002W
SERVICE DIAGNOSIS: Ice Level Control Circuit
CONDITION
DETERMINE CAUSE
PROBABLE CORRECTION
Ice Machine does not run, it has
power to it, the high pressure
control is closed, the on/off switch is
set to ON.
A. Listen for a ticking sound from
transducer.
If no noise, go to C. If there is a
noise, check for a light on the board
(models built after 4/93). If there is a
light on, check relay contacts N.O.
and COM. The contacts should be
CLOSED. If closed, go to D. If not,
replace the board. If light is off, or
prior model, go to B.
B. Open bin door and twist
transducer 1/4 turn and pull out. DO
If the inside of the transducer
(above screen) was wet, replace it.
Set bin level to FULL and aim at an
object about 1-3 feet away.
Machine should restart, if not go to
D.
NOT UNPLUG with power
connected. Examine the
transducer, the inside must be
clean and dry.
C. Check power to bin level
control board.
Should be 12 volts from
transformer, if not replace
transformer. If there is power go to
D.
D. Disconnect electrical power
and test ice machine circuit by
attaching a jumper wire between bin
thermostat posts on circuit board
part no. 12-1912-01 (the circuit
board with the timer on it).
Reconnect power.
If machine does not start go back
to machine circuit. If machine
E. Transducer or ice level board
assembly defective.
Replace transducer. Set bin level to
FULL and aim at an object about
1-3 feet away. Machine should
restart. If this does not repair unit,
replace the board.
Machine runs, makes ice, switches
on and off, but ice level cannot be
controlled.
Ice level switch may be defective.
On boards with a light, check by
moving switch & watching light.
Replace ice level switch
Machine runs, but will not shut off.
Board relay stuck closed. Check
relay.
If COM and N.O. are closed when
power is off, replace board. If open,
go to B above.
starts, disconnect electrical power,
remove jumper wire and reconnect
electrical power. Then go to E.
PARTIAL VIEW OF CIRCUIT BOARD 12-1912-01
PLUG - IN
RELAY
Electrical Shock Hazard Can
Cause Personal Injury.
Disconnect Power Before
Servicing.
Bin Thermostat Posts at Line
Voltage.
BIN THERMOSTAT
POSTS MENTIONED IN
“D” ABOVE
September, 1993
Page 19
CMS1002W
REMOVAL AND REPLACEMENT
TRANSDUCER
1. Disconnect electrical power BEFORE removing
transducer.
5. Unplug transducer and remove from the
machine.
2. Open bin door and locate the transducer socket.
6. Reverse steps 1-5 to reassemble.
3. Twist inner portion of transducer counterclockwise and push up gently.
4. Pull transponder down until plug connection is
accessible.
TRANSDUCER LOCATION
SOCKET IN ICE
MACHINE BASE
TRANSDUCER
PLUG
CONNECTION
REMOVAL OF TRANSDUCER
September, 1993
Page 20
CMS1002W
REMOVAL AND REPLACEMENT
/////////////////////////////////WARNING/////////////////////////////
Inlet Water Solenoid Valve Assembly
Disconnect electrical power before beginning.
To remove the inlet water solenoid valve assembly:
///////////////////////////////////////////////////////////////////////////////
1. Shut OFF water supply to machine.
Cube Size Control
ELECTRICAL CORD
To remove the cube size control:
1. Remove front panel.
SOLENOID
VALVE
2. Remove cover from control box.
3. Trace capillary tube, from the cube size control
to the refrigerant suction line.
4. Remove the coiled capillary tube bulb from the
tube well on the suction line.
5. Remove electrical leads from the cube size
control.
6. Remove screws and the cube size control. To
replace the cube size control, reverse the removal
procedure. Be certain to re-insulate the cube size
control bulb.
OUTLET
TUBE
Water Distributor Tubes And Manifold Tubes To
remove the water distributor tube and manifold
tube:
1. Pull out to unsnap catches and remove the front
panel.
REMOVAL OF THE INLET WATER VALVE
2. Remove the evaporator cover.
3. Slide the water distributor tube to the front about
1/8-inch along the top of the evaporator plate, until
the water distributor tube can be unsnapped from
the flexible notch and lifted upward to the right
side.
4. Unsnap and disconnect water distributor tubes
from the water manifold section. To replace the
water distributor tubes and manifold tubes, reverse
the removal procedure. BE SURE the notches in
the water manifold tubes properly engage the
alignment keys in the tee. BE SURE the water
distributor tube is securely fastened at the notch at
both sides of the evaporator plate. Check identical
attachment for the left water distributor tube and
notch; also, that the distributor/manifold
connections at the top center of each evaporator
plate is snug against the top of the plate.
2. Loosen and remove outlet water line from the
inlet water solenoid valve assembly.
3. Remove screws and pull the water solenoid
valve out to gain access.
4. Pull electrical cord connection from solenoid coil
terminals.
4. Remove inlet water fitting from the water
solenoid valve. To replace the inlet water valve
assembly, reverse the removal procedures.
September, 1993
Page 21
CMS1002W
REMOVAL AND REPLACEMENT
/////////////////////////////WARNING//////////////////////////////////
Hot Gas Valve
Disconnect electrical power before beginning.
1. Remove the side service panel, and top panel if
possible.
/////////////////////////////////////////////////////////////////////////////////
2. Discharge and recover the refrigerant from the
system.
Water Pump
1. Remove front panel.
3. Remove the electrical connections from the coil
of the valve
2. Remove evaporator cover.
3. Unplug water pump electrical connection.
4. Remove thumb screw retaining pump to cross
brace.
ELECTRICAL
CONNECTION
4. Cut out or unsweat the valve at the tubing
connections, remove the valve from the icemaker.
5. Install the new valve, wrap it in wet cloths or
other efficient heat sink material.
6. Sweat the tubing connections to the valve.
7. Connect the electrical wires to the terminals of
the valve coil.
8. Weigh in the nameplate charge.
9. Replace all panels removed for service.
10. Reconnect electrical power.
Thermostatic Expansion Valve
1. Remove the side service panel, and top panel if
possible..
2. Discharge and recover the refrigerant from the
system.
3. Locate the TXV sensing bulb on the suction line,
unwrap the insulation and remove the bulb from
the clamp.
DISCHARGE
HOSE
PUMP
4. Cut out or unsweat the old TXV from the tubing
connections.
REMOVAL OF THE WATER PUMP
5. Pull pump partially out of reservoir and remove
discharge hose.
5. Wrap the new TXV body in wet cloths or other
efficient heat sink material.
6. Remove two nuts holding pump cover to pump
body; separate the two and remove the pump from
the icemaker.
6. Sweat in the new valve. Do not overheat.
7. Reverse to reassemble.
7. Re-attach the TXV bulb to the suction line in the
same place as the original. Be certain to
re-insulate.
8. Replace all panels.
8. Weigh in the nameplate charge.
9. Reconnect electrical power.
9. Replace all panels removed for service.
10. Reconnect electrical power.
September, 1993
Page 22