R-930CS
SERVICE MANUAL
S9913R930CPST
CONVECTION
MICROWAVE OVEN
Custom
Help
Interactive
Minute Plus
Sensor Reheat
Popcorn
Compu Defrost
Elevate PKG
1 Baked potatoes
2 Frozen vegetables
3 Fresh veg-soft
4 Fresh veg-hard
5 Frozen entrees
6 Hot dogs
7 Bacon
8 Fish, seafood
Sensor
Cook
Convecvtion
CONVECTION
1 Hamburgers
2 Chicken pieces
3 Steaks
4 Fish steaks
Compu
Broil
1 Chicken
2 Turkey
3 Turkey breast
4 Pork
Compu
Roast
1 Bundt cake
2 Cookies
3 Muffins
4 French fries
Compu
Bake
Preheat
Convec
Broil
Slow
Cook
Low Mix
Bake
High Mix
Roast
1
2
100˚F
150˚F
6
350˚F
7
375˚F
Kitchen
Timer
Power
Level
3
4
275˚F
300˚F
8
9
400˚F
425˚F
Clock
MODEL
R-930CS
5
325˚F
0
450˚F
Stop
Clear
Sart
Touch On
In the interest of user-safety the oven should be restored to its original
condition and only parts identical to those specified should be used.
WARNING TO SERVICE PERSONNEL: Microwave ovens contain circuitry capable of producing very high voltage and
current, contact with following parts may result in a severe,
possibly fatal, electrical shock. (High Voltage Capacitor, High
Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..)
TABLE OF CONTENTS
Page
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICE TO
AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY ................... INSIDE FRONT COVER
BEFORE SERVICING ...................................................................................................... INSIDE FRONT COVER
WARNING TO SERVICE PERSONNEL ................................................................................................................ 1
MICROWAVE MEASUREMENT PROCEDURE ................................................................................................... 2
FOREWORD AND WARNING ............................................................................................................................... 3
PRODUCT SPECIFICATIONS .............................................................................................................................. 4
GENERAL INFORMATION ................................................................................................................................... 4
OPERATION .......................................................................................................................................................... 6
TROUBLESHOOTING GUIDE ............................................................................................................................ 12
TEST PROCEDURE ............................................................................................................................................ 14
TOUCH CONTROL PANEL ................................................................................................................................. 25
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE ................................................................ 31
PICTORIAL DIAGRAM ........................................................................................................................................ 38
CONTROL PANEL CIRCUIT ............................................................................................................................... 39
PRINTED WIRING BOARD ................................................................................................................................. 40
PARTS LIST ........................................................................................................................................................ 41
PACKING AND ACCESSORIES ......................................................................................................................... 44
SHARP CORPORATION
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
R-930CS
PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE
ENERGY
(a) Do not operate or allow the oven to be operated with the door open.
(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other
microwave source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3)
seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and
latches, (5) evidence of dropping or abuse.
(c) Before turning on microwave power for any service test or inspection within the microwave generating
compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,
integrity, and connections.
(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave
generation and transmission systems shall be repaired, replaced, or adjusted by procedures described
in this manual before the oven is released to the owner.
(e) A microwave leakage check to verify compliance with the Federal Performance Standard should be
performed on each oven prior to release to the owner.
BEFORE SERVICING
Before servicing an operative unit, perform a microwave emission check as per the Microwave
Measurement Procedure outlined in this service manual.
If microwave emissions level is in excess of the specified limit, contact SHARP ELECTRONICS
CORPORATION immediately @1-800-237-4277.
If the unit operates with the door open, service person should 1) tell the user not to operate the oven
and 2) contact SHARP ELECTRONICS CORPORATION and Food and Drug Administration's
Center for Devices and Radiological Health immediately.
Service personnel should inform SHARP ELECTRONICS CORPORATION of any certified unit found
with emissions in excess of 4mW/cm2. The owner of the unit should be instructed not to use the unit
until the oven has been brought into compliance.
R-930CS
WARNING TO SERVICE PERSONNEL
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with
following parts may result in a severe, possibly
fatal, electrical shock.
(Example)
High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
Read the Service Manual carefully and follow all
instructions.
Don't Touch !
Danger High Voltage
When the testing is completed,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect the leads to the primary of the power
transformer.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is
installed.
7. Run the oven and check all functions.
Before Servicing
1. Disconnect the power supply cord
remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
, and then
WARNING:RISK OF ELECTRIC SHOCK.
DISCHARGE THE HIGH-VOLTAGE
CAPACITOR BEFORE SERVICING.
The high-voltage capacitor remains charged about 60
seconds after the oven has been switched off. Wait for 60
seconds and then short-circuit the connection of the highvoltage capacitor (that is the connecting lead of the highvoltage rectifier) against the chassis with the use of an
insulated screwdriver.
After repairing
1. Reconnect all leads removed from components during
testing.
2. Reinstall the outer case (cabinet).
3. Reconnect the power supply cord after the outer case is
installed.
4. Run the oven and check all functions.
Whenever troubleshooting is performed the power supply
must be disconnected. It may, in some cases, be necessary
to connect the power supply after the outer case has been
removed, in this event,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power
transformer.
5. Ensure that the leads remain isolated from other
components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord.
Microwave ovens should not be run empty. To test for the
presence of microwave energy within a cavity, place a cup
of cold water on the oven turntable, close the door and set
the power to HIGH and set the microwave timer for two (2)
minutes. When the two minutes has elapsed (timer at zero)
carefully check that the water is now hot. If the water
remains cold carry out Before Servicing procedure and reexamine the connections to the component being tested.
When all service work is completed and the oven is fully
assembled, the microwave power output should be checked
and a microwave leakage test should be carried out.
1
R-930CS
MICROWAVE MEASUREMENT PROCEDURE
A. Requirements:
1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven
should not exceed 1mW/cm2 at any point 5cm or more from the external surface of the oven, measured prior to acquisition
by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more from the external
surface of the oven.
2) Safety interlock switches Primary interlock relay and door sensing switch shall prevent microwave radiation emission in
excess of the requirement as above mentioned, secondary interlock switch shall prevent microwave radiation emission
in excess of 5 mW/cm2 at any point 5cm or more from the external surface of the oven.
B. Preparation for testing:
Before beginning the actual measurement of leakage, proceed as follows:
1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.
Important:
Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard for
microwave ovens, 21 CFR 1030.10(c)(3)(i), must be used for testing.
2) Place the oven tray in the oven cavity.
3) Place the load of 275±15 ml (9.8 oz) of tap water initially at 20±5˚C (68˚F) in the center of the oven cavity.
The water container shall be a low form of 600 ml (20 oz) beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.)
and made of an electrically nonconductive material such as glass or plastic.
The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage
is measured accurately.
4) Set the cooking control on Full Power Cooking Mode.
5) Close the door and select a cook cycle of several minutes. If the water begins to boil before the survey is completed,
replace it with 275 ml of cool water.
C. Leakage test:
Closed-door leakage test (microwave measurement)
1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven.
2) Move the probe slowly, not faster than 1 in./sec. (2.5 cm/sec.) along the gap, watching for the maximum indication on
the meter.
3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the metal
has been breached (eg., around the switches, indicator, and vents).
While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the closed
latch assembly.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2,
and that the secondary interlock switch does turn the oven OFF before any door movement.
NOTE: After servicing, record data on service invoice and microwave leakage report.
2
R-930CS
SERVICE MANUAL
PRODUCT DESCRIPTION
CONVECTION
MICROWAVE OVEN
GENERAL INFORMATION
R-930CS
FOREWORD
This Manual has been prepared to provide Sharp Electronics Corp.
Service Personnel with Operation and Service Information for the
SHARP CONVECTION MICROWAVE OVEN, R-930CS.
It is recommended that service personnel carefully study the entire
text of this manual so that they will be qualified to render satisfactory
customer service.
Check the interlock switches and the door seal carefully. Special
attention should be given to avoid electrical shock and microwave
radiation hazard.
WARNING
Never operate the oven until the following points are ensured.
(A) The door is tightly closed.
(B) The door brackets and hinges are not defective.
(C) The door packing is not damaged.
(D) The door is not deformed or warped.
(E) There is no other visible damage with the oven.
Servicing and repair work must be carried out only by trained service
personnel.
DANGER
Certain initial parts are intentionally not grounded and present
a risk of electrical shock only during servicing. Service
personnel - Do not contact the following parts while the
appliance is energized;
High Voltage Capacitor, Power Transformer, Magnetron, High
Voltage Rectifier Assembly, High Voltage Harness;
If provided, Vent Hood, Fan assembly, Cooling Fan Motor.
All the parts marked “*” on parts list are used at voltages more than
250V.
Removal of the outer wrap gives access to voltage above 250V.
All the parts marked “∆” on parts list may cause undue microwave
exposure, by themselves, or when they are damaged, loosened
or removed.
SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH,
NEW JERSEY 07430-2135
3
OPERATION
TROUBLESHOOTING GUIDE
AND TEST PROCEDURE
TOUCH CONTROL PANEL
COMPONENT REPLACEMENT AND
ADJUSTMENT PROCEDURE
WIRING DIAGRAM
PARTS LIST
R-930CS
SPECIFICATION
ITEM
DESCRIPTION
Power Requirements
120 Volts
13.0 Amperes (Microwave) / 13.0 Amperes (Convection)
60 Hertz / Single phase, 3 wire grounded
Power Output
900 watts (IEC 705 Test Procedure)
Operating frequency of 2450MHz
1450 Watts
Convection Power Output
Case Dimensions
Cooking Cavity Dimensions
(1.5 Cubic Feet )
Control Complement
Width 24-5/8"
Height 14-7/8"
Depth 19"
Width 16-1/8"
Height 9-5/8"
Depth 16-1/8"
Touch Control System
Timer (0 - 99 min. 99 seconds)
Microwave Power for Variable Cooking
Repetition Rate;
P-HI........................................... Full power throughout the cooking time
P-90 ............................................................. approx. 90% of Full Power
P-80 ............................................................. approx. 80% of Full Power
P-70 ............................................................. approx. 70% of Full Power
P-60 ............................................................. approx. 60% of Full Power
P-50 ............................................................. approx. 50% of Full Power
P-40 .............................................................. approx. 40% of Full Power
P-30 .............................................................. approx. 30% of Full Power
P-20 ............................................................. approx. 20% of Full Power
P-10 .............................................................. approx. 10% of Full Power
P-0 ............................................. No power throughout the cooking time
Convection Temperature for Variable Cooking
CONVECTION .............................................. 100 - 450˚F Temp. control
LOW MIX. BAKE............................... 350˚F with 10% microwave power
HIGH MIX. ROAST ........................... 300˚F with 30% microwave power
SLOW COOK.......................................... 300˚F for 4 hours (no preheat)
BROIL ............................................................................ 450˚F (preheat)
CUSTOM HELP pad, SENSOR REHEAT pad, MINUTE PLUS pad, POPCORN pad
COMPU DEFROST pad, SENSOR COOK pad, COMPU BROIL pad
COMPU ROAST pad, COMPU BAKE pad, REHEAT pad, CONVEC pad
BROIL pad, SLOW COOK pad, HIGH MIX / ROAST pad, LOW MIX / BAKE pad
Number and temperature selection pads, KITCHEN TIMER pad, CLOCK pad
STOP/CLEAR pad, POWER LEVEL pad, START / TOUCH ON pad
Oven Cavity Light
Yes
Safety Standard
UL Listed
FCC Authorized
DHHS Rules, CFR, Title 21, Chapter 1, Subchapter J
GENERAL INFORMATION
GROUNDING INSTRUCTIONS
This oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle that is properly installed
and grounded in accordance with the National Electrical Code and local codes and ordinances.
In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the
electric current.
WARNING: Improper use of the grounding plug can result in a risk of electric shock.
4
R-930CS
Electrical Requirements
The electrical requirements are a 115 -120 volt 60 Hz, AC only,
15 or 20 amp. fused electrical supply. It is recommended that a separate
circuit serving only this appliance be provided. When installing this
appliance, observe all applicable codes and ordinances.
A short power-supply cord is provided to reduce risks of becoming
entangled in or tripping over a longer cord.
Where a two-pronged wall-receptacle is encountered, it is the personal
responsibility and obligation of the customer to contact a qualified
electrician and have it replaced with a properly grounded three-pronged
wall receptacle or have a grounding adapter properly grounded and
polarized. If an extension cord must be used, it should be a 3-wire, 15
amp. or more cord. Do not drape over a countertop or table where it can
be pulled on by children or tripped over accidentally.
Grounded
Receptacle Box
3-Pronged Plug
Grounding Pin
3-Pronged Receptacle
CAUTION: DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE ROUND GROUNDING PRONG FROM
THIS PLUG.
OVEN DIAGRAM
7
1
TOUCH CONTROL PANEL
3
MIX CONV
5
10
DEFROST
12
SENSOR
COOK LBS
OZ
KG
HELP
9
Custom
Help
Interactive
13
4
11
6
15
6
8
14
Minute Plus
Sensor Reheat
2
Popcorn
Compu Defrost
Elevate PKG
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Ventilation openings. (Rear side)
Oven door with see-through window.
Oven lamp.
Turntable support.
Removable turntable.
The turntable will rotate clockwise or
counterclockwise.
Safety door latches.
The oven will not operate unless the door is
securely closed.
Wave guide cover.
Door open button.
Auto-Touch control panel.
Lighted digital display.
Convection air openings.
Removable low rack. (Broiling trivet)
Removable low rack. (Baking rack)
Power supply cord.
Turntable motor shaft.
1
2
3
4
5
6
7
8
Baked potatoes
Frozen vegetables
Fresh veg-soft
Fresh veg-hard
Frozen entrees
Hot dogs
Bacon
Fish, seafood
1
2
3
4
Hamburgers
Chicken pieces
Steaks
Fish steaks
Compu
Broil
1
2
3
4
Chicken
Turkey
Turkey breast
Pork
Compu
Roast
1
2
3
4
Bundt cake
Cookies
Muffins
French fries
Compu
Bake
Convection
Preheat
Convec
Broil
Slow
Cook
Low Mix
Bake
High Mix
Roast
1
2
100˚F
150˚F
3
275˚F
4
300˚F
5
325˚F
6
7
8
9
0
350˚F
375˚F
400˚F
425˚F
450˚F
Kitchen
Timer
Power
Level
5
Sensor
Cook
Clock
Stop
Clear
Start
Touch On
R-930CS
OPERATION
DESCRIPTION OF OPERATING SEQUENCE
The following is a description of component functions during
oven operation.
and the secondary interlock switch are activated with the
following results. The circuits to the turntable motor, the
cooling fan motor, and the high voltage components are
de-energized, the oven lamp remains on, and the digital
read-out displays the time still remaining in the cook
cycle when the door was opened.
7. The monitor switch is electrically monitoring the operation
of the primary interlock relay and the secondary interlock
switch and is mechanically associated with the door so
that it will function in the following sequence.
(1) When the door opens from a closed position, the primary
interlock relay and the secondary interlock switch open
their contacts, and then the monitor switch contacts close.
(2) When the door is closed from the open position, the
monitor switch contacts first open, and then the contacts
of the primary interlock relay and the secondary interlock
switch close.
If the primary interlock relay and the secondary interlock
switch fail with their contacts closed when the door is
opened, the closing of the monitor switch contacts will form
a short circuit through the monitor fuse, primary interlock
relay and the secondary interlock switch, causing the monitor fuse to blow.
OFF CONDITION
Closing the door activates the door sensing switch and
secondary interlock switch. (In this condition, the monitor
switch contacts are opened.)
When oven is plugged in, 120 volts A.C. is supplied to the
control unit. (Figure O-1).
1. The display will show "SHARP SIMPLY THE BEST
PRESS CLEAR AND PRESS CLOCK".
To set any program or set the clock, you must first touch
the STOP/CLEAR pad. The display will clear, and " : "
will appear.
NOTE: When the door is opened, the oven lamp comes on.
2. A signal is input to the control unit, energizing the coil of
shut-off relay (RY-4). RY4 contacts close, completing a
circuit to the damper motor. The damper motor now
operates moving the damper to the open position, thereby
closing the contacts of the damper switch inputs a signal
to the control unit. The coil of relay RY-4 is de-energized,
opening its contacts, thereby turning off the damper motor.
COOKING CONDITION
POWER LEVEL P-0 TO P-90 COOKING
Program desired cooking time Variable Cooking Control by
touching the NUMBER pads and the power level pad. When
the START pad is touched, the following operations occur:
When Variable Cooking Power is programmed, the 120
volts A.C. is supplied to the power transformer intermittently
through the contacts of relay (RY-2). RY-2 is operated by
the control unit within an varying time base. Microwave
power operation is as follows:
1. The contacts of relays are closed and components
connected to the relays are turned on as follows.
(For details, refer to Figure O-2)
RELAY
CONNECTED COMPONENTS
RY-1
Oven lamp/Turntable motor
RY-2
Power transformer
RY-3
Heating element
RY-4
Damper motor
RY-5
Convection motor
RY-6
Fan motor
VARI-MODE
ON TIME
Power 10(P-HI) (100% power)
32 sec.
Power 9(P-90) (approx. 90% power) 30 sec.
Power 8(P-80) (approx. 80% power) 26 sec.
Power 7(P-70) (approx. 70% power) 24 sec.
Power 6(P-60) (approx. 60% power) 22 sec.
2. 120 volts A.C. is supplied to the primary winding of the
power transformer and is converted to about 3 volts A.C.
output on the filament winding, and approximately 2360
volts A.C. on the high voltage winding.
3. The filament winding voltage heats the magnetron
filament and the H.V. winding voltage is sent to a voltage
doubler circuit.
4. The microwave energy produced by the magnetron is
channelled through the waveguide into the cavity feedbox, and then into the cavity where the food is placed to
be cooked.
5. Upon completion of the cooking time, the power
transformer, oven lamp, etc. are turned off, and the
generation of microwave energy is stopped. The oven
will revert to the OFF condition.
6. When the door is opened during a cook cycle, monitor
switch, door sensing switch, the primary interlock relay
OFF TIME
0 sec.
2 sec.
6 sec.
8 sec.
10 sec.
Power 5(P-50) (approx. 50% power)
Power 4(P-40) (approx. 40% power)
Power 3(P-30) (approx. 30% power)
18 sec.
16 sec.
12 sec.
14 sec.
16 sec.
20 sec.
Power 2(P-20) (approx. 20% power)
Power 1(P-10)(approx. 10% power)
Power 0(P-0) (0% power)
8 sec.
6 sec.
0 sec.
24 sec.
26 sec.
32 sec.
Note:
The ON/OFF time ratio does not correspond with
the percentage of microwave power, because
approx. 2 seconds are needed for heating of the
magnetron filament.
CONVECTION COOKING CONDITION
PREHEATING CONDITION
Program desired convection temperature by touching the
CONVECTION pad and the Temperature pad. When the
START pad is touched, the following operations occur:
1. The coil of shut-off relays (RY1, RY3,RY5 and RY6) are
energized, the oven lamp, cooling fan motor, turntable
6
R-930CS
to zero.
2. The shut-off relays (RY1,RY2,RY3,RY5 and RY6) are
energized, turning on the oven lamp, turntable motor,
cooling fan motor and convection fan motor.
3. The shut-off relay (RY4) is energized.
The damper door is closed from the open position.
4. The heater relay (RY3) is energized, applying the main
supply voltage to the heating element.
5. Now, the oven is in the convection cooking condition.
6. When the oven temperature reaches the selected
temperature, the following operations occur:
6-1. The power supply voltage is alternated to the heating
element and power transformer.
6-2. The heating element operates through the heater
relay (RY3) contacts and the power transformer
operates through the primary interlock relay (RY2)
contacts.
6-3. These are operated by the control unit to supply
alternately within a 32 second time base, convection
heat and microwave energy.
The relationship between the convection and microwave
power operations are as follows.
Note: The ON and OFF time ratio does not correspond
with the percentage of microwave power, because
approx. 2 seconds are needed for heating of the
magnetron filament.
motor and convection motor are turned on.
2. The coil of relay (RY4) is energized by the control unit.
The damper is moved to the closed position, opening the
damper switch contacts. The opening of the damper
switch contacts sends a signal to the LSI on the control
unit de-energizing the relay (RY4) and opening the
circuit to the damper motor.
3. The coil of heater relay (RY3) is energized by the control
unit and the main supply voltage is applied to the heating
element.
4. When the oven temperature reaches the selected preheat
temperature, the following operations occur:
4-1 The heater relay is de-energized by the control unit
temperature circuit and thermistor, opening the
circuit to the heating element.
4-2. The oven will continue to function for 30 minutes,
turning the heater on and off, as needed to maintain
the selected preheat temperature. The oven will
shut-down completely after 30 minutes
CONVECTION COOKING CONDITION
When the preheat temperature is reached, a beep signal will
sound indicating that the holding temperature has been
reached in the oven cavity. Open the door and place the
food to be cooked in the oven. Touch the CONVEC pad first
and then touch the Temperature pad. And program desired
cooking time by touching the Number pads. When the
START pad is touched, the following operations occur:
1. The numbers on the digital read-out start to count down
to zero.
2. The oven lamp, turntable motor, cooling fan motor and
convection motor are energized.
3. Heater relay (RY3) is energized (if the cavity temperature
is lower than the selected temperature) and the main
supply voltage is applied to the heating element to return
to the selected cooking temperature.
4. Upon completion of the cooking time, the audible signal will
sound, and oven lamp, turntable motor, cooling fan motor
and convection motor are de-energized. At the end of the
convection cycle, if the cavity air temperature is above
275˚F, the circuit to RY6 will be maintained (by the thermistor
circuit) to continue operation of the cooling fan motor until
the temperature drops below 245˚F, at which time the relay
will be de-energized, turning off the fan motor. Relay RY5
will however, open as soon as the convection cycle has
ended, turning off the convection fan motor.
5. At the end of the convection cook cycle, shut-off relay
(RY4) is energized turning on the damper motor. The
damper is returned to the open position, closing the
damper switch contacts which send a signal to the
control unit, de-energizing shut-off relay (RY4).
6 SEC.
26 SEC.
ON
MICROWAVE POWER
= APPROX. 10%
(MICRO.)
OFF
CONVECTION
TEMPERATUE
= 350˚F (180˚C)
(CONVEC.)
LOW MIX
BAKE
12 SEC.
20 SEC.
ON
(MICRO.)
OFF
MICROWAVE POWER
= APPROX. 30%
ON
(CONVEC.)
OFF
32 SEC.
CONVECTION
TEMPERATUE
= 300˚F
HIGH MIX
ROAST
Note:
During alternate Microwave/Convection operation,
the convection heater is energized only if the cavity
temperature drops below the set temperature.
SENSOR COOKING CONDITION
Using the SENSOR COOK function, the foods are cooked
without figuring time, power level or quantity. When the oven
senses enough steam from the food, it relays the information to its microprocessor which will calculate the remaining
cooking time and power level needed for best results. When
the food is cooked, water vapor is developed. The sensor
“senses” the vapor and its resistance increases gradually.
When the resistance reaches the value set according to the
menu, supplementary cooking is started.
The time of supplementary cooking is determined by experiment with each food category and inputted into the LSI.
AUTOMATIC MIX COOKING CONDITION
Touch the HIGH MIX/ROAST or the LOW MIX/BAKE pad
first. And then program desired cooking time by touching the
Number pads. The LOW MIX/BAKE pad is preprogrammed
for 350˚F with 10% microwave power, while the HIGH MIX/
ROAST pad is preprogrammed for 300˚F with 30% microwave power. When the START pad is touched, the following
operations occur:
1. The numbers on the digital read-out start to count down
7
R-930CS
convection temperature, the oven goes into the
programmed cooking mode.
6. At the end of the COMPU BROIL/ ROAST/ BAKE cycle,
the damper is returned to the open position and the oven
will go to the off condition. The cooling fan will remain on
until the oven has cooled.
An example of how sensor works:
1. Potatoes at room temperature.
Vapor is emitted very slowly.
MIC
RO
WA
VE
2. Heat potatoes. Moisture and
humidity is emitted rapidly.
You can smell the aroma as it
cooks.
3. Sensor detects moisture and
humidity and calculates
cooking time and variable
power.
COMPU DEFROST COOKING
AH SENSOR
MIC
RO
The COMPU DEFROST key is a special function key to
defrost meats and poultry faster and better. COMPU DEFROST automatically defrosts roast beef, etc.. When the
COMPU DEFROST is selected and the food weight is
entered by using the COMPU DEFROST pad, the oven will
cook according to the special cooking sequence.
WA
VE
FIRE SENSING FEATURE (MICROWAVE MODE)
Cooking Sequence.
1. Touch SENSOR COOK pad.
NOTE: The oven should not be operated on SENSOR
COOK immediately after plugging in the unit. Wait
two minutes before cooking on SENSOR COOK.
2. Select desired Sensor setting.
3. Touch START pad.
The coil of shut-off relay (RY1, RY6) is energized, the
oven lamp and cooling fan motor are turned on, but the
power transformer is not turned on.
4. After about 16 seconds, the cook relay (RY-2) is
energized. The power transformer is turned on,
microwave energy is produced and first stage is started.
The 16 seconds is the cooling time required to remove
any vapor from the oven cavity and sensor.
NOTE: During this first stage, do not open the door or touch
STOP/CLEAR pad.
5. When the sensor detects the vapor emitted from the
food, the display switches over to the remaining cooking
time and the timer counts down to zero. At this time, the
door may be opened to stir food, turn it or season, etc.
6. When the timer reaches zero, an audible signal sounds.
The shut-off relay and cook relay are de-energized and
the power transformer, oven lamp, etc. are turned off.
7. Opening the door or touching the STOP/CLEAR pad, the
time of day will reappear on the display and the oven will
revert to an OFF condition.
This model incorporates a sensing feature which will stop
the oven's operation if there is a fire in the oven cavity during
microwave cooking. This is accomplished by the LSI repeatedly measuring the voltage across the temperature measurement circuit (thermistor) during it's 32-seconds time
base comparing the obtained voltage measurements. If the
most recent voltage measured is 300mV greater than the
previous voltage measured, the LSI judges it as a fire in the
oven cavity and switches off the relays to the power transformer, fan motor and convection motor. The LSI also stops
counting down and closes the damper door so that no fresh
air will enter the oven cavity. Please refer to the following
section for a more detailed description.
Operation
Please refer to the timing diagrams below.
1. The thermistor operates within a 32-seconds time base
and it is energized for three (3) seconds and off for 29
seconds. Two (2) seconds after the thermistor is
energized, the voltage across the temperature
measurement circuit is sampled by the LSI and twenty
one (21) seconds after the thermistor is cut off the LSI
turns on the cooling fan for six (6) seconds.
2. The above procedure is repeated. If the difference between
the first voltage measured (in step 1) and the voltage
measured when the procedure is repeated (step 2) is
greater than 300mV the LSI makes the judgment that there
is a fire in the oven cavity and will switch off the relays to the
power transformer, fan motor and convection motor. The
LSI also stops counting down and closes the damper door
so that no fresh air will enter the oven cavity.
3. Once the fire sensor feature has shut the unit down, the
programmed cooking cycle may be resumed by pressing
the "START" pad or the unit may be reset by pressing the
"CLEAR" pad.
COMPU BROIL/ COMPU ROAST/ COMPU BAKE
COMPU BROIL/ ROAST/ BAKE will automatically compute
the oven temperature, microwave power and cooking time for
baking, roasting and broiling. Set the desired program by
touching the COMPU BROIL/ ROAST/ BAKE pad, and number
pad. Enter the weight by touching the Number pads. When the
START pad is touched, the following operations occur:
1. The COOK indicator will light and the Convection Fan
Symbol will rotate.
2. The cooking time will appear on the display and start
counting down to zero. The cooking time is adjusted
automatically according to the weight of the food.
3. The shut-off relays (RY1, RY5 and RY6) are energized,
turning on the oven lamp, turntable motor, cooling fan
motor and convection motor. The power supply voltage
is applied to the heating element.
4. Now, the oven is in the convection cooking mode.
5. When the oven temperature has reached the programmed
0 23
24
30 32 (sec.)
64 (sec.)
6 sec.
CONVECTION
MOTOR
ON
OFF
3 sec.
THERMISTOR
ON
OFF
ON
Sensing
Voltage OFF
Sensing the voltage across the temperature measurement circuit.
8
R-930CS
IMPORTANT:
During sensor cooking operation, the fire sensing operation sequence will not begin until the AH sensor has
detected vapors and initiated a sensor cooking cycle.
This is because the operation of the convection fan
would interfere with the AH sensor's vapor detection.
SCHEMATIC DIAGRAM
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. CLOCK APPEARS ON DISPLAY.
MAGNETRON
TEMPERATURE
FUSE
RY1
RY6
RY5
RY4
N.O.
(RY1)
RY2
A-9
RY2
PRIMARY
INTERLOCK
RELAY
RY3
CONTROL UNIT
120V
60Hz
F-1
SECONDARY
INTERLOCK
SWITCH
F-2
F-3
E-1 E-2 E-3
DOOR
SENSING
SWITCH
AH SENSOR
E-4 E-5 E-6
THERMISTOR
POWER
TRANSFORMER
CAPACITOR
0.94µ
COM.
(RY3)
A-7
COM.
(RY2)
N.O.
(RY2)
N.O.
(RY3)
DAMPER
SWITCH
HEATIMG ELEMENT
DAMPER MOTOR
CONVECTION MOTOR
OVEN LAMP
FAN MOTOR
TURNTABLE MOTOR
COM.
(RY1)
A-5
DM
MAGNETRON
A-3
A-1
FM CM
TTM OL
MONITOR SWITCH
FUSE
H.V. RECTIFIER
CONV.
THERMAL
CUT-OUT
Figure O-1. Oven Schematic-OFF Condition
SCHEMATIC
1. DOOR CLOSED.
2. COOKING TIME PROGRAMMED.
3. “START” PAD TOUCHED.
MAGNETRON
TEMPERATURE
FUSE
RY1
RY6
RY5
RY4
DM
RY2
A-9
RY3
CONTROL UNIT
F-1
F-2
AH SENSOR
F-3
E-1 E-2 E-3
DOOR
SENSING
SWITCH
RY2
PRIMARY
INTERLOCK
RELAY
E-4 E-5 E-6
THERMISTOR
DAMPER
SWITCH
COM.
(RY2)
N.O.
(RY2)
N.O.
(RY3)
Figure O-2. Oven Schematic-Microwave Cooking Condition
9
POWER
TRANSFORMER
CAPACITOR
0.94µ
COM.
(RY3)
A-7
120V
60Hz
SECONDARY
INTERLOCK
SWITCH
N.O.
(RY1)
HEATIMG ELEMENT
DAMPER MOTOR
OVEN LAMP
FAN MOTOR
TURNTABLE MOTOR
CONVECTION MOTOR
FM CM
TTM OL
COM.
(RY1)
A-5
MAGNETRON
A-3
A-1
MONITOR SWITCH
FUSE
H.V. RECTIFIER
CONV.
THERMAL
CUT-OUT
R-930CS
MAGNETRON
TEMPERATURE
FUSE
A-3
A-1
FM CM
COM.
(RY1)
A-5
RY1
RY6
RY5
RY4
DM
N.O.
(RY1)
RY2
A-9
RY2
PRIMARY
INTERLOCK
RELAY
RY3
CONTROL UNIT
F-1
SECONDARY
INTERLOCK
SWITCH
CAPACITOR
0.94µ
COM.
(RY3)
A-7
120V
60Hz
POWER
TRANSFORMER
F-2
F-3
E-1 E-2 E-3
DOOR
SENSING
SWITCH
AH SENSOR
N.O.
(RY2)
N.O.
(RY3)
E-4 E-5 E-6
THERMISTOR
COM.
(RY2)
DAMPER
SWITCH
HEATIMG ELEMENT
DAMPER MOTOR
CONVECTION MOTOR
FAN MOTOR
OVEN LAMP
TURNTABLE MOTOR
TTM OL
MONITOR SWITCH
FUSE
H.V. RECTIFIER
CONV.
THERMAL
CUT-OUT
SCHEMATIC
DOOR CLOSED.
MIX COOKING PAD TOUCHED.
COOKING TIME PROGRAMMED.
“START” PAD TOUCHED.
RY2 AND RY3 WILL ALTERNATELY CLOSE.
DURING COOK CYCLE.
MAGNETRON
1.
2.
3.
4.
5.
Figure O-3. Oven Schematic-Automatic Mix Cooking Condition
A-3
A-1
COM.
(RY1)
A-5
RY1
RY6
RY5
RY4
DM
RY2
A-9
RY3
CONTROL UNIT
F-1
CAPACITOR
0.94µ
COM.
(RY3)
A-7
120V
60Hz
SECONDARY
INTERLOCK
SWITCH
N.O.
(RY1)
POWER
TRANSFORMER
F-2
AH SENSOR
F-3
E-1 E-2 E-3
DOOR
SENSING
SWITCH
RY2
PRIMARY
INTERLOCK
RELAY
E-4 E-5 E-6
THERMISTOR
DAMPER
SWITCH
COM.
(RY2)
N.O.
(RY2)
N.O.
(RY3)
HEATIMG ELEMENT
DAMPER MOTOR
FAN MOTOR
OVEN LAMP
TURNTABLE MOTOR
CONVECTION MOTOR
FM CM
TTM OL
MONITOR SWITCH
FUSE
MAGNETRON
MAGNETRON
TEMPERATURE
FUSE
CONV.
THERMAL
CUT-OUT
SCHEMATIC
DOOR CLOSED.
CONVECTION PAD TOUCHED.
DESIRED TEMP. TOUCHED.
COOKING TIME PROGRAMMED.
“START” PAD TOUCHED.
H.V. RECTIFIER
1.
2.
3.
4.
5.
Figure O-4. Oven Schematic-Convection Cooking Condition
DESCRIPTION AND FUNCTION OF COMPONENTS
DOOR SENSING AND SECONDARY INTERLOCK
SWITCHES
ary interlock switch is mounted in the lower position on the
latch hook. They are activated by the latch heads on the door.
When the door is opened, the switches interrupt the circuit to
all components. A cook cycle cannot take place until the door
The door sensing switch in the primary interlock system is
mounted in the upper position on the latch hook, the second10
R-930CS
is firmly closed thereby activating both interlock switches. The
primary interlock system consists of the door sensing switch
and primary interlock relay located on the control circuit board.
condition develops in the magnetron due to cooling fan
failure, obstructed air guide, dirty or blocked air intake, etc.
Under normal operation, the temperature fuse remains
closed. However, when abnormally high temperatures are
reached within the magnetron, the temperature fuse will
open at 302˚F(150˚C) causing the oven to shut down.
LATCH HOOK
DOOR SENSING
SWITCH
MONITOR FUSE
CONV. THERMAL CUT-OUT
MONITOR SWITCH
Figure D-1. Door sensing switch, monitor switch and
secondary interlock switches
The thermal cut-out located on the left side of the thermal
protection plate (left) is designed to prevent damage to the
heater unit if an over heated condition develops in the heating unit due to convection fan failure, thermistor failure,
obstructed air ducts, dirty or blocked air intake, etc. Under
normal operation, the thermal cut-out remains closed. However, when abnormally high temperatures are reached within
the heater unit, the thermal cut-out will open at 302˚F(150˚C)
causing the oven to shut down. When the thermal cut-out has
cooled, the thermal cut-out closes at 266˚F(130˚C).
MONITOR SWITCH
HEATING ELEMENT
The monitor switch is mounted on the middle position of latch
hook. It is activated (the contacts opened) by the lower latch
head while the door is closed. The switch is intended to render
the oven inoperative by means of blowing the monitor fuse
when the contacts of the primary interlock relay and secondary interlock switch fail to open when the door is opened.
Functions:
1. When the door is opened, the monitor switch contact
close (to the ON condition) due to their being normally
closed. At this time the door sensing and secondary
interlock switches are in the OFF condition (contacts
open) due to their being normally open contact switches.
2. As the door goes to a closed position, the monitor switch
contacts are first opened and then the door sensing switch
and the secondary interlock switch contacts close. (On
opening the door, each of these switches operate inversely.)
3. If the door is opened, and the primary interlock relay and
secondary interlock switch contacts fail to open, the
monitor fuse blows simultaneously with closing of the
monitor switch contacts.
The heating element is located at the left side of the oven
cavity. It is intended to heat air driven by the convection fan.
The heated air is kept in the oven and force-circulated and
reheated by the heating element.
LATCH
HEADS
SECONDARY
INTERLOCK SWITCH
SWITCH LEVER
OPEN LEVER
DOOR OPEN
BUTTON
CONVECTION COOKING SYSTEM
This oven is designed with a hot air heating system where food
is not directly heated by the heating element, but is heated by
forced circulation of the hot air produced by the heating
element. The air heated by the heating element is circulated
through the convection passage provided on the outer casing
of the oven cavity by means of the convection fan which is
driven by the convection motor. It then enters the inside of the
oven through the vent holes provided on the left side of the
oven. Next, the hot air heats the food on the turntable and
leaves the oven cavity through the vent in the center of the
oven cavity left side wall. Without leaving the oven, this hot air
is reheated by the heating element, passes through the
convection passage and enters the inside of the oven cavity
again, in a continuing cycle. In this way, the hot air circulates
inside the oven cavity to raise its temperature and, at the same
time, comes into contact with the food being cooked. When the
temperature inside the oven cavity reaches the selected
temperature, the heating element is de-energized. When the
temperature inside the oven cavity drops below the selected
temperature, the heating element is energized again. In this
way, the inside of the oven cavity is maintained at approximately the selected temperature. When the convection time
reaches 0, the heating element is de-energized and the
convection fan stops operating and the oven shuts off.
CAUTION: BEFORE REPLACING A BLOWN MONITOR
FUSE TEST THE DOOR SENSING SWITCH,
PRIMARY INTERLOCK RELAY, SECONDARY
INTERLOCK SWITCH AND MONITOR
SWITCH FOR PROPER OPERATION. (REFER TO CHAPTER “TEST PROCEDURE”).
NOTE: MONITOR FUSE AND MONITOR SWITCH ARE
REPLACED AS AN ASSEMBLY.
THERMISTOR
DAMPER OPEN-CLOSE MECHANISM
The thermistor is a negative temperature coefficient type.
The temperature in the oven cavity is detected through the
resistance of the thermistor, and then the control unit
causes the heater relay to operate, thus the current to the
heating element is turned ON/OFF.
Usually, the damper is in the open position except during
convection cooking. Damper position is set automatically
by damper motor, damper switch, motor cam and damper
shaft. These components are operated by a signal that
judges if microwave cooking or convection cooking operation is selected by the control unit.
Microwave Cooking:
Damper is in the open position, because a portion of cooling
MAGNETRON TEMPERATURE FUSE.
The temperature fuse located on the waveguide is designed
to prevent damage to the magnetron if an over heated
11
R-930CS
switch is OFF), its signal is sensed by the control
unit, and shut-off relay (RY4) is de-energized.
3-3. The damper is held in the closed position during the
convection cooking operation.
3-4. At the end of the convection cooking, shut-off relay
(RY4) is energized, and the damper is returned to
the open position.
NOTE: If the damper door is not in the proper position,
closed during convection or open during microwave,
the control unit will stop oven operation after 1
minute.
air is channelled through the cavity to remove steam and
vapors given off from the heating foods. It is then exhausted
at the top of the oven cavity into a condensation compartment.
Convection Cooking:
Damper is in the closed position, so that no hot air will be
allowed to leak out the oven cavity.
Damper Operation
1. When power supply cord is plugged in:
1-1. When power supply cord is plugged in, a signal is
sensed in the control unit, and operates shut-off
relay (RY4).
1-2. Contacts of shut-off relay (RY4) close, the damper
motor is energized, opening the damper door.
1-3. When the damper is moved to the open position by
the damper cam the damper switch is closed (ON
position).
1-4. The signal from damper switch is re-sensed in the
control unit and shut-off relay (RY4) is turned off.
1-5. The 120 volts A.C. to the damper motor is removed
and the motor turns off.
2. When oven is microwave cooking:
Damper is in the open position.
3. When oven is convection cooking:
3-1. Damper motor is energized by touching the
convection, temperature and START pads.
3-2. When damper is in the closed position (damper
DAMPER SHAFT
DAMPER DUCT
DAMPER
DAMPER CAM
DAMPER SWITCH
DAMPER MOTOR
Figure D-2. Damper Mechanism
TROUBLESHOOTING GUIDE
Never touch any part in the circuit with your hand or an uninsulated tool while the power supply is connected.
When troubleshooting the microwave oven, it is helpful to follow the Sequence of Operation in performing the checks. Many
of the possible causes of trouble will require that a specific test be performed. These tests are given a procedure letter which
will be found in the "Test Procedure "section.
IMPORTANT: If the oven becomes inoperative because of a blown monitor fuse, check the monitor switch, relay (RY1)
primary interlock relay (RY2), door sensing switch and secondary interlock switch before replacing the
monitor fuse. If the monitor fuse is replaced, the monitor switch must also be replaced. Use part FFSBA012WRK0 as an assembly.
IMPORTANT: Whenever troubleshooting is performed with the power supply cord disconnected. It may in, some cases,
be necessary to connect the power supply cord after the outer case has been removed, in this event,
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power transformer.
5. Ensure that the leads remain isolated from other components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord.
When the testing is completed
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect all leads removed from components during testing.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is installed.
7. Run the oven and check all functions.
12
Replace
POSSIBLE CAUSE
AND
DEFECTIVE PARTS
A
MAGNETRON
B
C
POWER TRANSFORMER
H.V. RECTIFIER ASSEMBLY
D
E
HIGH VOLTAGE CAPACITOR
SECONDARY INTERLOCK SWITCH
F
G
PRIMARY INTERLOCK SYSTEM
MONITOR SWITCH
H
MONITOR FUSE
I
J
MAGNETRON TEMPERATURE FUSE
CONV. THERMAL CUT-OUT
K
CONVECTION HEATER
L
THERMISTOR
M
N
DAMPER MOTOR
DAMPER SWITCH
P
TOUCH CONTROL PANEL
Q
R
KEY UNIT
RELAY RY-1
R
RELAY RY-2
R
R
RELAY RY-3
RELAY RY-4
R
RELAY RY-5
R
RELAY RY-6
S
T
COMP. DEFROST
FOIL PATERN ON PWB.
U
AH SENSOR
Replace
OVEN LAMP OR SOCKET
FAN MOTOR
Replace
TURNTABLE MOTOR
Replace
Check
CONVECTION MOTOR
LOOSE WIRING
Check
SHORTED IN POWER CORD
Check
NO POWER AT OUTLET
Check
LOW VOLTAGE
13
(CONVECTION)
Oven in the sensor cooking condition but AH sensor does not end or AH
sensor turns off about max. 30 min. after start.
Convection cycle runs 4 minutes and 15 seconds then shuts down.
Cooling fan motor runs intermittently or all the time.
Temperature in the oven cavity is lower or higher than preset.
CONV indicator lights, but heating element does not heat.
(MICROWAVE)
CONV indicator lights, but oven does not go into cook cycle when
START pad is touched.
Function of COMPU DEFROST does not operate properly.
Function of variable cooking does not operate properly except HIGH
power.
Extremely uneven heating is produced in oven load (food).
COOKING CONDITION
Low or no power is produced during microwave cooking (The food is
heated incompletely or not heated at all)
Oven does not go into a cook cycle, when START pad is touched.
Turntable motor operates normally but cooling fan motor does not
operate.
Oven lamp light, but turntable motor does not operate.
Cooking cycle runs 1 minute then shuts down.
OFF CONDITION
Oven lamp does not light in cook cycle. (It light when door is opened).
Oven lamp does not light with door opened.
Display does not operate properly when STOP/CLEAR pad is touched.
(The time of day should appear on the display with beep sound.)
88:88 does not appear in display when power cord is first plugged into
wall receptacle.
CONDITION
Monitor fuse blows when power cord is plugged into wall receptacle
Home fuse blows when power cord is plugged into wall receptacle.
PROBLEM
TEST PROCEDURE
R-930CS
(SENSOR
COOKING)
R-930CS
TEST PROCEDURES
PROCEDURE
LETTER
A
COMPONENT TEST
MAGNETRON ASSEMBLY TEST
1.
2.
3.
4.
5.
6.
7.
8.
9.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
To test for an open filament, isolate the magnetron from the high voltage circuit. A continuity check
across the magnetron filament leads should indicate less than 1 ohm.
To test for a shorted magnetron, connect the ohmmeter leads between the magnetron filament leads
and chassis ground. This test should indicate an infinite resistance. If there is little or no resistance
the magnetron is grounded and must be replaced.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
MICROWAVE OUTPUT POWER
The following test procedure should be carried out with the microwave oven in a fully assembled
condition (outer case fitted).
HIGH VOLTAGES ARE PRESENT DURING THE COOK CYCLE, SO EXTREME CAUTION SHOULD
BE OBSERVED.
Power output of the magnetron can be measured by performing a water temperature rise test. This test
should only be used if above tests do not indicate a faulty magnetron and there is no defect in the following
components or wiring: silicon rectifier, high voltage capacitor and power transformer. This test will require
a 16 ounce (453cc) measuring cup and an accurate mercury thermometer or thermocouple type
temperature tester. For accurate results, the following procedure must be followed carefully:
1. Fill the measuring cup with 16 oz. (453cc) of tap water and measure the temperature of the water with
a thermometer or thermocouple temperature tester. Stir the thermometer or thermocouple through
the water until the temperature stabilizes. Record the temperature of the water.
2. Place the cup of water in the oven. Operate oven at POWER 10(HIGH) selecting more than 60
seconds cook time. Allow the water to heat for 60 seconds, measuring with a stop watch, second hand
of a watch or the digital read-out countdown.
3. Remove the cup from the oven and again measure the temperature, making sure to stir the
thermometer or thermocouple through the water until the maximum temperature is recorded.
4. Subtract the cold water temperature from the hot water temperature. The normal result should be 22
to 43˚F(12.2 to 23.8˚C) rise in temperature. If the water temperatures are accurately measured and
tested for the required time period the test results will indicate if the magnetron tube has low power
output (low rise in water temperature) which would extend cooking time or high power output (high
rise in water temperature) which would reduce cooking time. Because cooking time can be adjusted
to compensate for power output, the magnetron tube assembly should be replaced only if the water
temperature rise test indicates a power output well beyond the normal limits. The test is only accurate
if the power supply line voltage is 120 volts and the oven cavity is clean.
B
POWER TRANSFORMER TEST
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect the primary input terminals and measure the resistance of the transformer with an
ohmmeter. Check for continuity of the coils with an ohmmeter. On the R x 1 scale, the resistance of
the primary coil should be less than 1 ohm and the resistance of the high voltage coil should be
approximately 81.7 ohms; the resistance of the filament coil should be less than 1 ohm.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
14
R-930CS
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
(HIGH VOLTAGES ARE PRESENT AT THE HIGH VOLTAGE TERMINAL, SO DO NOT ATTEMPT TO
MEASURE THE FILAMENT AND HIGH VOLTAGE.)
C
HIGH VOLTAGE RECTIFIER TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Isolate the rectifier from the circuit. Using the highest ohm scale of the meter, read the resistance
across the terminals and observe, reverse the leads to the rectifier terminals and observe meter
reading. If a short is indicated in both directions, or if an infinite resistance is read in both directions,
the rectifier is probably defective and should be replaced.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
NOTE: Be sure to use an ohmmeter that will supply a forward bias voltage of more than 6.3 volts.
D
HIGH VOLTAGE CAPACITOR TEST
1.
2.
3.
4.
5.
6.
7.
8.
E
SECONDARY INTERLOCK SWITCH TEST
1.
2.
3.
4.
5.
6.
7.
8.
F
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
If the capacitor is open, no high voltage will be available to the magnetron. Disconnect input leads
and check for short or open between the terminals using an ohmmeter.
Checking with a high ohm scale, if the high voltage capacitor is normal, the meter will indicate
continuity for a short time and should indicate an open circuit once the capacitor is charged. If the
above is not the case, check the capacitor with an ohmmeter to see if it is shorted between either of
the terminals and case. If it is shorted, replace the capacitor.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch. The meter should indicate an open circuit with the door open and a closed circuit with
the door closed. If improper operation is indicated, replace the secondary interlock switch.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
PRIMARY INTERLOCK SYSTEM TEST
DOOR SENSING SWITCH
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch. The meter should indicate an open circuit with the door open and a closed circuit with
the door closed. If improper operation is indicated, replace the door sensing switch.
15
R-930CS
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
5.
6.
7.
8.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
NOTE: If the door sensing switch contacts fail in the open position and the door is closed, the turntable
motor and oven light will be activated by RY1.
PRIMARY INTERLOCK RELAY (RY2)
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect two (2) wire leads from the male tab terminals of the Primary Interlock Relay (RY2). Check
the state of the relay contacts using a ohmmeter. The relay contacts should be open. If the relay
contacts are closed, replace the circuit board entirely or the relay itself.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
G
MONITOR SWITCH
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Before performing this test, make sure that the secondary interlock switch and the primary interlock
relay are operating properly, according to the above Switch Test Procedure. Disconnect the wire
lead from the monitor switch (COM) terminal. Check the monitor switch operation by using the
ohmmeter as follows. When the door is open, the meter should indicate a closed circuit. When the
monitor switch actuator is pushed by a screw driver through the lower latch hole on the front plate
of the oven cavity with the door opened (in this condition the plunger of the monitor switch is pushed
in), the meter should indicate an open circuit. If improper operation is indicated, the switch may be
defective. After testing the monitor switch, reconnect the wire lead to the monitor switch (COM)
terminal and check the continuity of
the monitor circuit.
N.C.
Reconnect all leads removed from
MONITOR SWITCH
components during testing.
COM.
Reinstall the outer case (cabinet).
Reconnect the power supply cord SCREW DRIVER
after the outer case is installed.
SECONDARY
Run the oven and check all functions.
INTERLOCK
OHMMETER
SWITCH
H
BLOWN MONITOR FUSE
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
If the monitor fuse is blown when the door is opened, check the primary interlock relay, secondary
interlock switch and monitor switch according to the "TEST PROCEDURE" for those switches before
replacing the blown monitor fuse.
CAUTION: BEFORE REPLACING A BLOWN MONITOR FUSE, TEST THE PRIMARY INTERLOCK
RELAY, SECONDARY INTERLOCK SWITCH, DOOR SENSING SWITCH AND MONITOR
SWITCH FOR PROPER OPERATION.
If the monitor fuse is blown by improper switch operation, the monitor fuse and monitor switch must be
replaced with "monitor fuse and monitor switch assembly" part number FFS-BA012WRK0, even if the
monitor switch operates normally. The monitor fuse and monitor switch assembly is comprised of a 20
ampere fuse and switch.
16
R-930CS
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
5.
6.
7.
8.
I
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
MAGNETRON TEMPERATURE FUSE TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
A continuity check across the temperature fuse terminals should indicate a closed circuit unless the
temperature of the magnetron reaches approximately 302˚F(150˚C). An open temperature fuse
indicates overheating of the magnetron. Check for restricted air flow to the magnetron, especially the
cooling duct and cooling fan.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
CAUTION: IF THE TEMPERATURE FUSE INDICATES AN OPEN CIRCUIT AT ROOM TEMPERATURE, REPLACE TEMPERATURE FUSE.
J
CONV. THERMAL CUT-OUT TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
A continuity check across the thermal cut-out terminals should indicate a closed circuit unless the
temperature of the thermal cut-out reaches approximately 302˚F(150˚C). The thermal cut-out resets
automatically at approximately 266˚F(130˚C). If thermal cut-out has opened under normal condition,
replace the same item as in the parts list.
An open thermal cut-out indicates overheating of the heater unit. Check for restricted air flow to the
heater unit through the vent holes of the oven cavity, especially the heater duct and convection fan.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
CAUTION: IF THE THERMAL CUT-OUT INDICATES AN OPEN CIRCUIT AT ROOM TEMPERATURE,
REPLACE THERMAL CUT-OUT.
K
HEATING ELEMENT TEST
1.
2.
3.
4.
5.
6.
7.
8.
9.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Make sure the heating element is fully cooled and test as follows;
a. Disconnect wire leads from the heating element and measure the resistance with an ohmmeter.
On the R x 1 scale, the resistance between the heating element terminals should be approximately
10.2Ω.
b. Disconnect wire leads from the heating element and measure the insulation resistance with 500V
- 100MΩ insulation resistance meter. The insulation resistance between heating element terminal
and cavity should be more than 0.5MΩ.
If the meter does not indicate above resistance, replace the thermistor
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
17
R-930CS
TEST PROCEDURES
PROCEDURE
LETTER
L
COMPONENT TEST
THERMISTOR TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect connector-E from the control unit. Measure the resistance of the thermistor with an
ohmmeter. Connect the ohmmeter leads to Pin No’s E-3 and E-4.
Room Temperature
68˚F(20˚C) - 86˚F(30˚C)
5.
6.
7.
8.
9.
M
Resistance
Approx. 350kΩ - 155KΩ
If the meter does not indicate above resistance, replace the thermistor.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
DAMPER MOTOR TEST
When the power cord is plugged into the wall receptacle and 120 volts A.C. is supplied to the damper
motor, the motor operates until the damper is opened and the damper switch closes. Then the damper
motor stops operation.
If the damper motor does not operate, check for A.C. voltage with a voltmeter at the motor.
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power transformer.
5. Ensure that the leads remain isolated from other components and oven chassis by using insulation
tape.
6. Disconnect the wire leads of motor and connect the meter leads to the wire leads of main wire harness.
7. Re-connect the power cord into the wall receptacle.
8. If 120 volts A.C. is indicated at the wire leads, replace the motor and if 120 volts A.C. is not indicated,
check the wire harness and control unit.
9. Disconnect the power supply cord, and then remove outer case.
10.Open the door and block it open.
11.Discharge high voltage capacitor.
12.Reconnect all leads removed from components during testing.
13.Re-install the outer case (cabinet).
14.Reconnect the power supply cord after the outer case is installed.
15.Run the oven and check all functions.
N
DAMPER SWITCH TEST
1.
2.
3.
4.
5.
6.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect the leads to the primary of the power transformer.
Ensure that the leads remain isolated from other components and oven chassis by using insulation tape.
Disconnect the wire leads from the switch terminals and connect ohmmeter leads to the common
(COM.) and normally open (N.O.) terminals of the switch.
6-1. When switch actuator is pushed by the damper motor cam, the meter should be indicated a closed
circuit.
6-2. When power cord is plugged into the wall receptacle, the damper motor operates and damper cam will
start to rotate. When the switch actuator is released, the meter should be indicated an open circuit.
7. If improper operation is indicated, replace the damper switch.
8. Disconnect the power supply cord, and then remove outer case.
18
R-930CS
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
9. Open the door and block it open.
10.Discharge high voltage capacitor.
11.Reconnect all leads removed from components during testing.
12.Re-install the outer case (cabinet).
13.Reconnect the power supply cord after the outer case is installed.
14.Run the oven and check all functions.
O
CHECKING TEMPERATURE IN THE CONVECTION MODE
The following test procedure should be carried out with the microwave oven is a fully assembled
condition (outer case fitted).
It is difficult to measure the exact temperature in the convection oven. An accurate thermocouple type
temperature tester must be used. A low priced bi-metal type thermometer is not reliable or accurate.
The temperature should be checked with outer case cabinet installed, approx. 5 minutes after preheat
temperature is reached (audible signal sounds four times). The temperature experienced may be
approx. 30˚F more or less than indicated on the display, however, in most cases the food cooking results
will be satisfactory.
Difference in power supply voltage will also affect the oven temperature. The Household power supply
voltage may sometimes become lower than the rated voltage (120 V) and cause under-cooking. If the
power supply voltage is 10% lower than the rated voltage, longer cooking time is required by 10% to 20%.
P
TOUCH CONTROL PANEL ASSEMBLY TEST
The touch control panel consists of circuits including semiconductors such as LSI, ICs, etc. Therefore,
unlike conventional microwave ovens, proper maintenance cannot be performed with only a voltmeter
and ohmmeter.
In this service manual, the touch control panel assembly is divided into two units, Control Unit and Key
Unit, and troubleshooting by unit replacement is described according to the symptoms indicated.
Before testing,
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that these leads remain isolated from other components and oven chassis by using
insulation tape.
1. Key Unit.
NOTE ;
1) Check Key unit ribbon connection before replacement.
2) Reconnect all leads removed from components during testing.
3) Re-install the outer case (cabinet).
4) Reconnect the power supply cord after the outer case is installed.
5) Run the oven and check all functions.
The following symptoms indicate a defective key unit.
a) When touching the pads, a certain pad produces no signal at all.
b) When touching a number pad, two figures or more are displayed.
c) When touching the pads, sometimes a pad produces no signal.
If the Key unit is defective.
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Replace the Key unit.
5) Reconnect all leads removed from components during testing.
6) Re-install the outer case (cabinet).
7) Reconnect the power supply cord after the outer case is installed.
8) Run the oven and check all functions.
19
R-930CS
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
2. Control Unit
The following symptoms indicate a defective control unit. Before replacing the control unit, perform
the Key unit test (Procedure Q) to determine if control unit is faulty. Reconnect the power supply cord.
And check for followings.
2-1 In connection with pads.
a) When touching the pads, a certain group of pads do not produce a signal.
b) When touching the pads, no pads produce a signal.
2-2 In connection with indicators
a) At a certain digit, all or some segments do not light up.
b) At a certain digit, brightness is low.
c) Only one indicator does not light.
d) The corresponding segments of all digits do not light up; or they continue to light up.
e) Wrong figure appears.
f ) A certain group of indicators do not light up.
g) The figure of all digits flicker.
2-3 Other possible problems caused by defective control unit.
a) Buzzer does not sound or continues to sound.
b) Clock does not operate properly.
c) Cooking is not possible.
When testing is completed,
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Reconnect all leads removed from components during testing.
5) Re-install the outer case (cabinet).
6) Reconnect the power supply cord after the outer case is installed.
7) Run the oven and check all functions.
Q
KEY UNIT TEST
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon cable
is making good contact, verify that the door sensing switch (stop switch) operates properly; that is the
contacts are closed when the door is closed and open when the door is open. If the door sensing
switch (stop switch) is good, disconnect the flat ribbon cable that connects the key unit to the control
unit and make sure the door sensing switch is closed (either close the door or short the door sensing
switch connecter). Use the Key unit matrix indicated on the control panel schematic and place a
jumper wire between the pins that correspond to the STOP/CLEAR pad making momentary contact.
If the control unit responds by clearing with a beep the key unit is faulty and must be replaced. If the
control unit does not respond, it is faulty and must be replaced. If a specific pad does not respond,
the above method may be used (after clearing the control unit) to determine if the control unit or key
pad is at fault.
Reconnect all leads removed from components during testing.
Re-install the outer case (cabinet).
Reconnect the power supply cord
G5
G6
G7
G8
G9
G10
G11
G12
after the outer case is installed.
High Mix
Sensor
Compu
Compu
Compu
Compu
Broil
Run the oven and check all G 4 Minute
Roast
Cook
Broil
Roast
Bake
Plus
Defrost
functions.
G3
Popcorn
Preheat
Convec
G2
Sensor
Reheat
Slow
Cook
Low Mix
Bake
G1
Custom
Help
20
1
2
3
4
5
100˚F
150˚F
275˚F
300˚F
325˚F
6
7
8
9
0
350˚F
375˚F
400˚F
425˚F
450˚F
Kitchen
Timer
Power
Level
Clock
Start
Touch On
Stop
Clear
R-930CS
TEST PROCEDURES
PROCEDURE
LETTER
R
COMPONENT TEST
RELAY TEST
1.
2.
3.
4.
5.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect the leads to the primary of the power transformer.
Ensure that these leads remain isolated from other components and oven chassis by using insulation
tape.
6. After that procedure, re-connect the power supply cord.
7. Remove the outer case and check voltage between Pin Nos. 7 and 9 of the 9 pin connector (A) on
the control unit with an A.C. voltmeter. The meter should indicate 120 volts, if not check oven circuit.
Shut-off, Cook and Heater Relays Test
These relays are operated by D.C. voltage
Check voltage at the relay coil with a D.C. voltmeter during the microwave cooking operation or
convection cooking condition.
DC. voltage indicated ............... Defective relay.
DC. voltage not indicated ........... Check diode which is connected to the relay coil. If diode is good,
control unit is defective.
RELAY SYMBOL
RY1
RY2 (COOK)
RY3 (HEATER)
OPERATIONAL VOLTAGE
Approx. 19.0V D.C.
Approx. 18.0V D.C.
Approx. 18.0V D.C.
RY4
RY5
RY6
Approx. 19.0V D.C.
Approx. 19.0V D.C.
Approx. 19.0V D.C.
CONNECTED COMPONENTS
Oven lamp / Turntable motor
Power transformer
Heating element
Damper motor
Convection motor
Cooling fan motor
8. Disconnect the power supply cord, and then remove outer case.
9. Open the door and block it open.
10.Discharge high voltage capacitor.
11.Reconnect all leads removed from components during testing.
12.Re-install the outer case (cabinet).
13.Reconnect the power supply cord after the outer case is installed.
14.Run the oven and check all functions.
S
COMPU DEFROST TEST
WARNING : The oven should be fully assembled before following procedure.
(1) Place one cup of water in the center of the turntable tray in the oven cavity.
(2) Close the door, touch the Compu Defrost pad twice and touch the number pad 5. And then touch the
start pad.
(3) The oven is in Compu Defrost cooking condition.
(4) The oven will operate as follows
WEIGHT
0.5lbs
1ST STAGE
LEVEL TIME
70%
47sec.
2ND STAGE
3RD STAGE
LEVEL TIME LEVEL
TIME
0%
52sec.
50%
32sec.
4TH STAGE
LEVEL TIME
30%
40sec.
(5) If improper operation is indicated, the control unit is probably defective and should be checked.
T
PROCEDURES TO BE TAKEN WHEN THE FOIL PATTERN ON THE PRINTED WIRING BOARD
(PWB) IS OPEN.
To protect the electronic circuits, this model is provided with a fine foil pattern added to the primary on
the PWB, this foil pattern acts as a fuse.
1. Foil pattern check and repairs.
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
21
R-930CS
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
3) Discharge high voltage capacitor.
4) Follow the troubleshooting guide given below for repair.
STEPS
OCCURRENCE
CAUSE OR CORRECTION
1
Only pattern at "a" is broken.
*Insert jumper wire J1 and solder.
2
Pattern at "a" and "b" are broken.
*Insert the coil RCILF2003YAZZ between "c" and "d".
5
b
3
T1
26
9
CN - A
POWER
a
(J1)
7
6)
7)
8)
9)
P
d
VRS1
3
CONV M FAN M
5) Make a visual inspection of the varistor.
Check for burned damage and examine the
transformer with a tester for the presence of
layer short-circuit (check the primary coil
resistance which is approximately 175Ω ±
10%). If any abnormal condition is detected,
replace the defective parts.
c
Reconnect all leads removed from components during testing.
Re-install the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
2. Follow the troubleshooting guide given below, if indicator does not light up after above check and
repairs are finished.
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that these leads remain isolated from other components and oven chassis by using
insulation tape.
6) After that procedure, re-connect the power supply cord.
7) Follow the troubleshooting guide given below for repair.
STEPS
8)
9)
10)
11)
12)
13)
14)
U
OCCURRENCE
CAUSE OR CORRECTION
1
The rated AC voltage is not present to power
terminal of CPU connecter (CN-A).
Check supply voltage and oven power cord.
2
The rated AC voltage is present at primary
side of low voltage transformer.
Low voltage transformer or secondary circuit defective.
Check and repair.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Reconnect all leads removed from components during testing.
Re-install the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
AH SENSOR TEST
Checking the initial sensor cooking condition
WARNING : The oven should be fully assembled before following procedure.
(1) The oven should be plugged in at least two minutes before sensor cooking.
(2) Room temperature should not exceed 95˚F (35˚C).
(3) The unit should not be installed in any area where heat and steam are generated. The unit should
not be installed, for example, next to a conventional surface unit. Refer to the “INSTALLATION
INSTRUCTIONS” of the operation manual.
(4) Exhaust vents are provided on the back of the unit for proper cooling and air flow in the cavity. To
22
R-930CS
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
(5)
(6)
(7)
(8)
permit adequate ventilation, be sure to install so as not to block these vents. There should be some
space for air circulation.
Be sure the exterior of the cooking container and the interior of the oven are dry. Wipe off any moisture
with a dry cloth or paper towel.
The Sensor works with food at normal storage temperature. For example, chicken pieces would be
at refrigerator temperature and canned soup at room temperature.
Avoid using aerosol sprays or cleaning solvents near the oven while using Sensor settings. The
sensor will detect the vapor given of by the spray and turn off before food is properly cooked.
If the sensor has not detected the vapor of the food, ERROR will appear and the oven will shut off.
Water load cooking test
WARNING : The oven should be fully assembled before following procedure.
Make sure the oven has been plugged in at least two minutes before checking sensor cook operation.
The cabinet should be installed and screws tightened.
(1) Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
(2) Place the container on the center of tray in the oven cavity.
(3) Close the door.
(4) Touch SENSOR COOK pad and then touch the number pad 1. And touch Start pad. Now, the oven
is in the sensor cooking condition and "BAKED POTATO" will appear in the display.
(5) The oven will operate for the first 16 seconds, without generating microwave energy.
When the AH sensor is defective (open or short), Error will appear in the display after 16 seconds
cleaning time. If ERROR appears, check sensor wire connecting and/or AH sensor.
NOTE: ERROR will appear if the door is opened or STOP/CLEAR pad is touched during first stage of
sensor cooking.
(6) After approximately 16 seconds, microwave energy is produced, and the display should start to count
down the remaining cooking time and oven should turn off after water is boiling (bubbling).
If the oven does not turn off, replace the AH sensor or check the control unit, refer to explanation below.
TESTING METHOD FOR AH SENSOR AND/OR CONTROL UNIT
To determine if the sensor is defective, the simplest method is to replace it with a new replacement sensor.
(1) Disconnect the power supply cord, and then remove outer case.
(2) Open the door and block it open.
(3) Discharge high voltage capacitor.
(4) Remove the AH sensor.
(5) Install the new AH sensor.
(6) Reconnect all leads removed from components during testing.
(7) Re-install the outer case (cabinet).
(8) Reconnect the power supply cord after the outer case is installed.
(9) Check the sensor cook operation as follows:
9-1. Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
9-2. Place the container on the center of tray in the oven cavity.
9-3. Close the door.
9-4. Touch SENSOR COOK pad and then touch the number pad 1. And touch Start pad.
9-5. The control panel is in automatic Sensor operation.
9-6. The display will start to count down the remaining cooking time, and the oven will turn off
automatically after the water is boiling (bubbling).
If new sensor dose not operate properly, the problem is with the control unit, and refer to explanation
below.
CHECKING CONTROL UNIT
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect the sensor connector that is mounted to control panel.
Then connect the dummy resistor circuit (see fig.) to the sensor connector of control panel.
Disconnect the leads to the primary of the power transformer.
Ensure that these leads remain isolated from other components and oven chassis by using
insulation tape.
23
R-930CS
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
(8) After that procedure, re-connect the power supply cord.
(9) Check the sensor cook operation proceed as follows:
9-1. Touch SENSOR COOK pad and then touch the number pad 1. And touch Start pad.
9-2. The control panel is in the sensor cooking operation.
9-3. After approximately 20 seconds, push plunger of select switch for more than 3 seconds. This
condition is same as judgement by AH sensor.
9-4. After approximately 3 seconds, the display shows “ X X . X X “ which is the remaining cooking
time, and the display count down.
If the above is not the case, the control unit is probably defective.
If the above is proper, the AH sensor is probably defective.
(10) Disconnect the power supply cord, and then remove outer case.
(11) Open the door and block it open.
(12) Discharge high voltage capacitor.
(13) Disconnect the dummy resistor circuit from the sensor connector of control panel.
(14) Carry out necessary repair.
(15) Reconnect all leads removed from components during testing and repairing.
(16) Re-install the outer case (cabinet).
(17) Reconnect the power supply cord after the outer case is installed. Run the oven and check all
functions.
(18) Carry out "Water load cooking test" again and ensure that the oven works properly.
F-1
F-2
To connector (F)
on Control Unit.
1
2
3
Plunger
R1, R2 : 22Ω ± 1% 1/2W
R3 : 4.3kΩ ± 5% 1/4W
R4 : 1MΩ ± 5% 1/4W
NC
NO
COM
COM NO
R1
F-3
R2
CONNECTOR
R3
R4
Sensor Dummy Resistor Circuit
24
NC
R-930CS
TOUCH CONTROL PANEL ASSEMBLY
OUTLINE OF TOUCH CONTROL PANEL
The touch control section consists of the following units
as shown in the touch control panel circuit.
4) ACL Circuit
A circuit to generate a signals which resetting the LSI to
the initial state when power is applied.
(1) Key Unit
(2) Control Unit
5) Buzzer Circuit
The buzzer is responds to signals from the LSI to emit
noticing sounds (key touch sound and completion sound).
The principal functions of these units and the signals communicated among them are explained below.
6) Temperature Measurement Circuit : (OVEN
THERMISTOR)
The temperature in the oven cavity is sensed by the
thermistor. The variation of resistance according to sensed
temperature is detected by the temperature measurement
circuit and the result applied to LSI. The LSI uses this
information to control the relay and display units.
Key Unit
The key unit is composed of a matrix, signals P10 - P17
generated in the LSI are sent to the key unit.
When a key pad is touched, a signal is completed through
the key unit and passed back to the LSI through R24 - R27
to perform the function that was requested.
Control Unit
Control unit consists of LSI, power source circuit, synchronizing signal circuit, ACL circuit, buzzer circuit, temperature
measurement circuit, absolute humidity sensor circuit and
indicator circuit.
7) Absolute Humidity Sensor Circuit
This circuit detects the humidity of a food which is being
cooked, to control its automatic cooking.
8) Door Sensing Switch
A switch to inform the LSI if the door is open or closed.
1) LSI
This LSI controls the temperature measurement signal,
AH sensor signal, key strobe signal, relay driving signal
for oven function and indicator signal.
9) Relay Circuit
To drive the magnetron, heating element, fan motor,
convection motor, damper motor, turntable motor and
light the oven lamp.
2) Power Source Circuit
This circuit generates the voltages necessary for the
control unit from the AC line voltage.
10) Indicator Circuit
Indicator element is a Fluorescent Display.
Basically, a Fluorescent Display is triode having a cathode,
a grid and an anode. Usually, the cathode of a Fluorescent
Display is directly heated and the filament serves as
cathode.
The Fluorescent Display has 8-digits, 16-segments are
used for displaying figures.
3) Synchronizing Signal Circuit
The power source synchronizing signal is available in
order to compose a basic standard time in the clock
circuit. It incorporates a very small error because it works
on commercial frequency.
DESCRIPTION OF LSI
LSI(IZA797DR):
The I/O signals of the LSI(IZA797DR) are detailed in the following table.
Pin No.
1
2
Signal
VCC
VEE
I/O
IN
IN
3
AVSS
IN
4
VREF
IN
Description
Connected to GND.
Anode (segment) of Fluorescent Display light-up voltage: -30V.
Vp voltage of power source circuit input.
Power source voltage: -5V.
VC voltage of power source circuit input.
Reference voltage input terminal.
A reference voltage applied to the A/D converter in the LSI. Connected to GND.(0V)
25
R-930CS
Pin No.
Signal
I/O
5
AN7
IN
6
AN6
IN
7-9
10
AN5-AN3
AN2
IN
IN
11
AN1
IN
12
AN0
IN
13
P55
OUT
Description
Used for initial balancing of the bridge circuit (absolute humidity sensor). This input is
an analog input terminal from the AH sensor circuit, and connected to the A/D
converter built into the LSI.
AH sensor input.
This input is an analog input terminal from the AH sensor circuit, and connected to the
A/D converter built into the LSI.
Heating constant compensation terminal.
Input signal which communicates the door open/close information to LSI.
Door closed; "H" level signal(0V).
Door opened; "L" level signal(-5V).
Input signal which communicates the damper open/close information to LSI.
Damper opened; "H" level signal(0V:GND).
Damper closed; "L" level signal(-5V).
Temperature measurement input: OVEN THERMISTOR.
By inputting DC voltage corresponding to the temperature detected by the thermistor,
this input is converted into temperature by the A/D converter built into the LSI.
Digit selection signal.
The relationship between digit signal and digit are as follows;
H
Digit signal
Digit
ß(60Hz)
L
P03 ........................... 1st.
GND
P02 .......................... 2nd.
P03
P01 ........................... 3rd.
VP
P02
P00 ........................... 4th.
P01
P37 ........................... 5th.
P00
P36 .......................... 6th.
P37
P35 .......................... 7th.
14
P54
OUT
P36
P55 .......................... 8th.
P35
Normally, one pulse is output in every ß
P55
period, and input to the grid of the Fluorescent Display.
Oven lamp and turntable motor driving signal. (Square Waveform : 60Hz)
To turn on and off the shut-off relay(RY1).
The square waveform voltage is delivered to
the relay(RY1) driving circuit.
16.7 msec.
H
L
During cooking
15
16
17
P53
P52
P51
OUT
OUT
OUT
Convection motor driving signal.
To turn on and off shut-off relay(RY5). "L"
level during CONVECTION; "H" level otherwise.
Cooling fan motor driving signal.
To turn on and off shut-off relay(RY6). "L"
level during both microwave and convection
cooking; "H" level otherwise.
Magnetron high-voltage circuit driving
signal.
ON
ON
VARI MODE
To turn on and off the cook relay(RY2). In
P-HI operation, the signals holds "L" level
during microwave cooking and "H" level
while not cooking. In other cooking modes
(P-90, P-80, P-70, P-60, P-50, P-40, P-30,
P-20, P-10, P-0) the signal turns to "H"
level and "L" level in repetition according
to the power level.
26
During
cooking
(Convection)
During
cooking
OFF
H. GND
L
OFF
H. GND
L
ON TIME
OFF TIME
P-HI (100% power)
32 sec.
0 sec.
P-90 (approx. 90% power)
30 sec.
2 sec.
P-80 (approx. 80% power)
26 sec.
6 sec.
P-70 (approx. 70% power)
24 sec.
8 sec.
P-60 (approx. 60% power)
22 sec.
10 sec.
P-50 (approx. 50% power)
18 sec.
14 sec.
P-40 (approx. 40% power)
16 sec.
16 sec.
P-30 (approx. 30% power)
12 sec.
20 sec.
P-20 (approx. 20% power)
8 sec.
24 sec.
P-10 (approx. 10% power)
6 sec.
26 sec.
P-0 (0% power)
0 sec.
32 sec.
R-930CS
Pin No.
18
Signal
I/O
P50
OUT
Description
Damper motor relay driving signal.
OFF
To turn on and off shut-off relay(RY4).
19
P47
OUT
P46-P45
P44
OUT
OUT
23
P43
OUT
24
P42
OUT
25
INT1
IN
20-21
22
ON
H : GND
L
Heating element driving signal.
To turn on and off shut-off relay(RY3). "L" level
H. GND
During
OFF
during convection cooking; "H" level otherwise. Durcooking
(Convection)
ing convection cooking, the signal becomes "H" level
ON
L
when the temperature of the oven cavity exceeds the
predetermined temperature.
Terminal not used.
Timing signal output terminal for temperature measurement(OVEN THERMISTOR).
"H" level (GND) : Thermistor OPEN timing.
"L" level (-5V) : Temperature measuring timing.(Convection cooking)
Signal to sound buzzer.
0.1 sec
A: key touch sound.
A
B: Completion sound.
2.0 sec
C: When the temperature of the oven cavB
ity reaches the preset temperature in
the preheating mode, or when the
1.0 sec
1.0 sec
H: GND
preheating hold time (30 minutes) is
C
L
elapsed.
Timing signal output terminal for temperature measurement(OVEN).
"H" level (GND) : Thermistor OPEN timing.
"L" level (-5V) : Temperature measuring timing.(Convection cooking)
Signal to synchronize LSI with commercial power source frequency.
H : GND
This is the basic timing for all real time
processing of LSI.
L (-5V)
16.7 msec.
26
27
P40
RST
IN
IN
XCIN/XCOUT
XIN
OUT
IN
31
XOUT
OUT
32
VSS
IN
33
P27
IN
34
P26
IN
35
P25
IN
36
P24
IN
28/29
30
Connected to GND.
Auto clear terminal.
Signal is input to reset the LSI to the initial state when power is applied. Temporarily
set to "L" level the moment power is applied, at this time the LSI is reset. Thereafter
set at "H" level.
Terminal not used.
Internal clock oscillation frequency setting input.
The internal clock frequency is set by inserting the ceramic filter oscillation circuit with
respect to XOUT terminal.
Internal clock oscillation frequency control output.
Output to control oscillation input of XIN.
Power source voltage: -5V.
VC voltage of power source circuit input.
Signal coming from touch key.
When any one of G-1 line keys on key matrix is touched, a corresponding signal from
P10 - P17 will be input into P27. When no key is touched, the signal is held at "L" level.
Signal similar to P27.
When any one of G-2 line key on key matrix is touched, a corresponding signal will be
input into P26.
Signal similar to P27.
When any one of G-3 line key on key matrix is touched, a corresponding signal will be
input into P25.
Signal similar to P27.
When any one of G-4 line key on key matrix is touched, a corresponding signal will be
input into P24.
27
R-930CS
Pin No.
37
38-40
Signal
I/O
P23
OUT
P22-P20
OUT
41
P17
OUT
42
P16
OUT
43
P15
OUT
44
P14
OUT
45
P13
OUT
46
P12
OUT
47
P11
OUT
48
P10
OUT
49-53
P07-P03
OUT
54-56
P02-P00
OUT
57-59
P37-P35
OUT
60-64
P34-P30
OUT
Description
Segment data signals.
The relation between signals and indicators are as follows:
Signal Segment Signal Segment Signal Segment Signal Segment
P23 ............. P1
P17 ............. P5
P13 ............. P9
P07 ........... P13
P22 ............. P2
P16 ............. P6
P12 ........... P10
P06 ........... P14
P21 ............. P3
P15 ............. P7
P11 ........... P11
P05 ........... P15
P20 ............. P4
P14 ............. P8
P10 ........... P12
P04 ........... P16
Segment data signal.
Signal similar to P23.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-12 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-11 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-10 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-9 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-8 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-7 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-6 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-5 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Digit selection signal.
Signal similar to P55.
Digit selection signal.
Signal similar to P55.
Used for initial balancing of the bridge circuit (absolute humidity sensor).
28
R-930CS
ABSOLUTE HUMIDITY SENSOR CIRCUIT
With this voltage given, the switches SW1 to SW5 in the
LSI are turned on in such a way as to change the
resistance values in parallel with R50-1. Changing the
resistance values results in that there is the same potential
at both F-3 terminal of the absolute humidity sensor and
AN7 terminal of the LSI. The voltage of AN6 terminal will
indicate about -2.5V. This initial balancing is set up about
16 seconds after the unit is put in the Sensor Cooking
mode. As the sensor cooking proceeds, the food is
heated to generate moisture by which the resistance
balance the bridge circuit is deviated to increase the
voltage available at AN6 terminal of the LSI.
Then the LSI observes that voltage at AN6 terminal and
compares it with its initial value, and when the comparison
rate reaches the preset value (fixed for each menu to be
cooked), the LSI causes the unit to stop sensor cooking;
thereafter, the unit goes in the next operation
automatically.
When the LSI starts to detect the initial voltage at AN6
terminal 16 seconds after the unit has been put in the
Sensor Cooking mode, if it is not possible to balance, of
the bridge circuit due to disconnection of the absolute
humidity sensor, ERROR will appear on the display and
the cooking is stopped.
(1) Structure of Absolute Humidity Sensor
The absolute humidity sensor includes two thermistors
as shown in the illustration. One thermistor is housed in
the closed vessel filled with dry air while another in the
open vessel. Each sensor is provided with the protective
cover made of metal mesh to be protected from the
external airflow.
Sensing part Sensing part
(Open vessel) (Closed vessel)
Thermistor
element
Sensor
case
Sensing part
(Closed vessel)
Cross section view
View of sensor case removed
(2) Operational Principle of Absolute Humidity Sensor
The figure below shows the basic structure of an absolute
humidity sensor. A bridge circuit is formed by two
thermistors and two resistors (R1 and R2).
The output of the bridge circuit is to be amplified by the
operational amplifier.
Each thermistor is supplied with a current to keep it
heated at about 150˚C (302˚F), the resultant heat is
dissipated in the air and if the two thermistors are placed
in different humidity conditions they show different degrees
of heat conductivity leading to a potential difference
between them causing an output voltage from the bridge
circuit, the intensity of which is increased as the absolute
humidity of the air increases. Since the output is very
minute, it is amplified by the operational amplifier.
Operational
amplifier
Output
voltage
+
S
R3
R2
S : Thermistor
open vessel
C : Thermistor
closed vessel
620k
Absolute humidity vs,
output voltage characteristic
C. Thermistor in
closed vesssl
S. Thermistor in
open vessel
47k
11
F-1
C
F-3
3.57k
Absolute humidity (g/m 2 )
S
F-2
3.32k 1.8k
10
R51
(3) Detector Circuit of Absolute Humidity Sensor Circuit
This detector circuit is used to detect the output voltage
of the absolute humidity circuit to allow the LSI to control
sensor cooking of the unit. When the unit is set in the
sensor cooking mode, 16 seconds clearing cycle occurs
than the detector circuit starts to function and the LSI
observes the initial voltage available at its AN6 terminal.
VA : -15V
29
4
64
5
63
300k
6
62
150k
7
61
75k
8
60
3
5
37.4k
0.1
µF
R1
IC2(IZA495DR)
Output voltage
C
1) Absolute humidity sensor circuit
+
10k
360k
9
VA : -15V
SW2
P31
SW3
P32
SW4
P33
SW5
P34
AN7
LSI
(IC1)
2
47k
12
SW1
P30
0.01µF
Thermistor
element
0.01µF
Ventilation
openings
0.015µF
Sensing part
(Open vessel)
1
VC : -5V
6
AN6
R-930CS
TOUCH CONTROL PANEL SERVICING
1. Precautions for Handling Electronic Components
5) Re-connect the power supply cord after the outer case is
installed.
6) Run the oven and check all functions.
A. On some models, the power supply cord between the touch
control panel and the oven itself is so short that the two can’t
be separated. For those models, check and repair all the
controls (sensor-related ones included) of the touch control
panel while keeping it connected to the oven.
B. On some models, the power supply cord between the touch
control panel and the oven proper is long enough that they
may be separated from each other. For those models, it is
possible to check and repair the controls of the touch control
panel while keeping it apart from the oven proper; in this
case you must short both ends of the door sensing switch
(on PWB) of the touch control panel with a jumper, which
activates an operational state that is equivalent to the oven
door being closed. As for the sensor-related controls of the
touch control panel, checking them is possible if dummy
resistor(s) with resistance equal to that of the controls are
used.
This unit uses CMOS LSI in the integral part of the circuits.
When handling these parts, the following precautions should
be strictly followed. CMOS LSI have extremely high impedance at its input and output terminals. For this reason, it is
easily influenced by the surrounding high voltage power
source, static electricity charge in clothes, etc. and sometimes it is not fully protected by the built-in protection circuit.
In order to protect CMOS LSI.
1) When storing and transporting, thoroughly wrap them in
aluminium foil. Also wrap all PW boards containing them in
aluminium foil.
2) When soldering, ground the technician as shown in the
figure and use grounded soldering iron and work table.
approx. 1M ohm
2. Shapes of Electronic Components
(2) Servicing the touch control panel with power supply
from an external power source:
Transistor
E
C
B
Transistor
2SB910M
E
CB
Disconnect the touch control panel completely from the
oven proper, and short both ends of the door sensing switch
(on PWB) of the touch control panel, which activates an
operational state that is equivalent to the oven door being
closed. Connect an external power source to the power
input terminal of the touch control panel, then it is possible
to check and repair the controls of the touch control panel
it is also possible to check the sensor-related controls of the
touch control panel by using the dummy resistor(s).
DTA123ES
KRA101M
KRA223M
KRC243M
3. Servicing of Touch Control Panel
We describe the procedures to permit servicing of the touch
control panel of the microwave oven and the precautions
you must take when doing so. To perform the servicing,
power to the touch control panel is available either from the
power line of the oven itself or from an external power
source.
4. Servicing Tools
Tools required to service the touch control panel assembly.
1) Soldering iron: 30W
(It is recommended to use a soldering iron with a grounding
terminal.)
2) Oscilloscope: Single beam, frequency range: DC-10MHz
type or more advanced model.
3) Others: Hand tools
(1) Servicing the touch control panel with power supply
of the oven:
CAUTION:
THE HIGH VOLTAGE TRANSFORMER OF THE MICROWAVE OVEN IS STILL LIVE DURING SERVICING
AND PRESENTS A HAZARD.
Therefore, before checking the performance of the touch
control panel,
1) Disconnect the power supply cord, and then remove outer
case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that these leads remain isolated from other
components and oven chassis by using insulation tape.
6) After that procedure, re-connect the power supply cord.
After checking the performance of the touch control panel,
1) Disconnect the power supply cord.
2) Open the door and block it open.
3) Re-connect the leads to the primary of the power transformer.
4) Re-install the outer case (cabinet).
5. Other Precautions
1) Before turning on the power source of the control unit,
remove the aluminium foil applied for preventing static
electricity.
2) Connect the connectors of the key unit to the control unit
being sure that the lead wires are not twisted.
3) After aluminium foil is removed, be careful that abnormal
voltage due to static electricity etc. is not applied to the input
or output terminals.
4) Attach connectors, electrolytic capacitors, etc. to PWB,
making sure that all connections are tight.
5) Be sure to use specified components where high precision
is required.
30
R-930CS
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE
WARNING AGAINST HIGH VOLTAGE:
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts may
result in severe, possibly fatal, electric shock.
(Example)
High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
WARNING:
Avoid possible exposure to microwave energy. Please follow the instructions below before
operating the oven.
1. Disconnect the power supply cord.
2. Make sure that a definite” click” can be heard when the
microwave oven door is unlatched. (Hold the door in a
closed position with one hand, then push the door open
button with the other, this causes the latch leads to rise,
it is then possible to hear a “click’ as the door switches
operate.)
3. Visually check the door and cavity face plate for damage
(dents, cracks, signs of arcing etc.).
1.
2.
3.
4.
5.
6.
Door does not close firmly.
Door hinge, support or latch hook is damaged.
The door gasket or seal is damaged.
The door is bent or warped.
There are defective parts in the door interlock system.
There are defective parts in the microwave generating
and transmission assembly.
7. There is visible damage to the oven.
Do not operate the oven:
1. Without the RF gasket (Magnetron).
2. If the wave guide or oven cavity are not intact.
3. If the door is not closed.
4. If the outer case (cabinet) is not fitted.
Carry out any remedial work that is necessary before
operating the oven.
Do not operate the oven if any of the following conditions
exist;
WARNING FOR WIRING
To prevent an electric shock, take the following precautions.
1. Before wiring,
1) Disconnect the power supply cord.
2) Open the door block it open.
3) Discharge the high voltage capacitor and wait for 60
seconds.
2. Don’t let the wire leads touch to the following parts;
1) High voltage parts:
Magnetron, High voltage transformer, High voltage
capacitor and High voltage rectifier assembly.
2) Hot parts:
Oven lamp, Magnetron, High voltage transformer,
Oven cavity and Heating element.
3) Sharp edge:
Bottom plate, Oven cavity, Waveguide flange,
Chassis support and other metallic plate.
4) Moveable parts (to prevent a fault)
Fan blade, Fan motor, Switch, Switch lever, Open
button, Convection motor, Convection fan,
Convection fan belt, Pulley, Turntable motor, Damper
motor, Damper door assembly.
3. Do not catch the wire leads in the outer case cabinet.
4. Insert the positive lock connector until its pin is locked
and make sure that the wire leads do not come off even
if the wire leads are pulled.
5. To prevent an error function, connect the wire leads
correctly, referring to the Pictorial Diagram.
Please refer to ‘OVEN PARTS, CABINET PARTS, CONTROL PANEL PARTS, DOOR PARTS’, when carrying out any of
the following removal procedures:
OUTER CASE REMOVAL
To remove the outer case, proceed as follows.
1. Disconnect the power supply cord.
2. Open the oven door and block it open.
3. Remove the two (2) screws from the lower portion of the
rear cabinet using a T20H Torx type or GTXH20-100
screw driver.
4. Remove the remaining two (2) screws from rear and one
(1) screw along the right side of outer case.
5. Slide the entire outer case back out about 1 inch (3 cm)
to free it from retaining clips on the cavity face plate.
6. Lift entire outer case from the unit.
31
R-930CS
CAUTION: 1. DISCONNECT OVEN FROM POWER SUP
PLY BEFORE REMOVING OUTER CASE.
2. DISCHARGE THE HIGH VOLTAGE CAPACITOR BEFORE TOUCHING ANY OVEN
COMPONENTS OR WIRING.
NOTE: When replacing the outer case, the 2 special
Torx screws must be reinstalled in the same
locations.
Special screw
Screw Driver
(Type: TORX T20 H or
GTXH20-100)
POWER TRANSFORMER REMOVAL
1. Disconnect the power supply cord and then remove
outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect filament leads of transformer from the
magnetron and capacitor.
5. Disconnect high voltage lead of capacitor from the
transformer.
6. Disconnect wire leads from the transformer.
7. Remove two (2) screws holding the transformer to the
base cabinet.
3. Make sure the transformer is mounted correctly to the
corners underneath those tabs.
4. After re-installing the transformer, secure the transformer
with two screws to the base cabinet, one is with outer
tooth washer and the other is without outer-tooth washer.
5. Re-connect the wire leads (primary and high voltage)
and high voltage lead to the transformer and filament
leads of transformer to the magnetron and capacitor,
referring to the “Pictorial Diagram”.
6. Re-install the outer case and check that the oven is
operating properly.
Re-install
1. Rest the transformer on the base cabinet with its primary
terminals toward rear cabinet.
2. Insert the two edges of the transformer into two metal
tabs of the base cabinet.
NOTE HOT (ORANGE) WIRE MUST BE CONNECTED
TO THE POWER TRANSFORMER TERMINAL
NEAREST TO THE TRANSFORMER MOUNTING
SCREW.
MAGNETRON REMOVAL
1. Disconnect the power supply cord and then remove
outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect filament lead of transformer from magnetron.
5. Disconnect high voltage wire lead from magnetron.
6. Carefully remove four (4) mounting screws hold the
magnetron to waveguide, when removing the screws
holding the magnetron to prevent it from falling.
7. Remove the magnetron from the unit with care so the
magnetron tube should not hit by any metal object
around the tube.
CAUTION: WHEN REPLACING THE MAGNETRON, BE
SURE THE R.F. GASKET IS IN PLACE AND
THE MAGNETRON MOUNTING SCREWS
ARE TIGHTENED SECURELY.
HIGH VOLTAGE RECTIFIER ASSEMBLY REMOVAL
1. Disconnect the power supply cord and then remove
outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Remove one (1) screw holding the rectifier assembly to
the capacitor holder.
5. Disconnect the rectifier assembly from the capacitor and
magnetron.
CAUTION: WHEN REPLACING THE SILICON RECTIFIER
ASSEMBLY, THE GROUND SIDE TERMINAL
MUST BE SECURED FIRMLY WITH A
GROUNDING SCREW.
HIGH VOLTAGE CAPACITOR REMOVAL
assembly from high voltage capacitor and magnetron.
5. Disconnect filament lead of transformer from high voltage
capacitor.
6. Disconnect high voltage wire lead of capacitor from
transformer.
1. Disconnect the power supply cord and then remove
outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the high voltage wire leads and rectifier
32
R-930CS
7. Remove one (1) screw and washer holding the rectifier
from the capacitor holder.
8. Remove one (1) screw holding the capacitor holder to
the rear cabinet.
9. Remove the capacitor from the holder.
POSITIVE LOCK® CONNECTOR (NO-CASE TYPE) REMOVAL
Terminal
1. Disconnect the power supply cord and then remove
outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Push the lever of positive lock® connector.
5. Pull down on the positive lock ® connector.
Positive lock®
connector
1
Push
Lever
CAUTION: WHEN YOU CONNECTING THE POSITIVE
LOCK® CONNECTORS TO THE TERMINALS,
INSTALL THE POSITIVE LOCK® SO THAT
THE LEVER FACES YOU.
2
Pull down
Figure C-2. Positive lock®connector
CONVECTION MOTOR REMOVAL
1. Disconnect the power supply cord and then remove
outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect wire leads from the convection motor.
5. Remove the convection fan belt.
6. Remove two (2) screws holding the convection motor
mounting angle to the heater duct and base cabinet.
7. Take out the convection motor assembly from the unit.
The convection motor assembly is now free.
8. Remove two (2) screws and nuts holding the motor to
mounting angle.
9 Remove pulley (M) from the motor shaft. Convection
motor is now free.
TURNTABLE MOTOR REMOVAL
1. Disconnect the power supply cord.
2. Remove the turntable tray, and the turntable support out
of the oven cavity.
3. Turn the oven upside down and remove one (1) screw
holding the turntable motor cover to the base plate and
take off the turntable motor cover.
4. Disconnect wire lead from the turntable motor.
5. Remove the two (2) screws holding the turntable motor
and coupling mounting plate to the oven cavity bottom.
6. Turntable motor, Coupling mounting plate and Thermal
protection plate bottom will be free.
DAMPER ASSEMBLY REMOVAL
1. Disconnect the power supply cord and then remove
outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect wire leads from damper motor and damper
switch.
5. Remove two (2) oven side screws holding damper motor
angle to thermal protection plate (right).
6. Damper assembly is free.
7. Remove one (1) screw holding damper motor to damper
motor angle and one (1) screw holding damper switch to
damper motor angle.
8. Damper motor and switch are free.
OVEN LAMP AND LAMP SOCKET REMOVAL
Oven lamp
socket
1. Disconnect the power supply cord and then remove
outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Bend the tab of the air guide holding the lamp socket.
5. Lift up the oven lamp socket.
6. Pull the wire leads from the oven lamp socket by pushing
the terminal hole of the oven lamp socket with the small
flat type screw driver.
7. Now, the oven lamp socket is free.
Terminal
Wire lead
Terminal hole
Flate type small
screw driver
Figure C-3. Oven lamp socket
33
R-930CS
HEATER UNIT ASSEMBLY REMOVAL
(HEATING ELEMENT/CONVECTION FAN/CONVECTION MOTOR/THERMISTOR)
THERMISTOR REMOVAL
HEATING ELEMENT REMOVAL
1. Disconnect the power supply cord and then remove
outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect wire leads from H.V. capacitor and remove
four (4) screws holding rear cabinet to bottom plate and
three (3) screws holding to heater unit assembly and two
(2) screws holding steam duct to top of oven cavity.
Disconnect wire leads from power supply cord terminals.
5. Disconnect wire leads from thermistor. Remove two (2)
screws from thermistor.
6. Disconnect wire leads from convection motor, thermal
cut-out and heater element.
7. Remove nine (9) screws holding heater duct to the oven
cavity.
8. Remove two (2) screws holding heater duct to base
cabinet. Release two (2) snap bands holding wire harness
to the thermal cover (convection).
9. The heater unit is now free.
10.Remove two (2) screws holding heating element to
heater duct.
11.Loosen two (2) screws holding holders to heater duct
and take heating element out of heating element holders.
12.Heating element is free.
NOTE: After installed the heating element completely,
bent top of the heating element holder to inside
using by long nose pliers as shown following
illustration.
Long nose plier
Heating
element
Heating element
holder
CONTROL PANEL ASSEMBLY AND CONTROL UNIT REMOVAL
CONTROL UNIT AND KEY UNIT
1. Disconnect the wire connector from the control unit.
2. Remove the four (4) screws holding the panel frame to
the back plate.
3. Separate the panel frame and back plate.
4. Remove the three (3) screws holding the control unit to
the panel frame.
5. Lift up the control unit and disconnect the key connector
from the control unit.
6. Now, the control unit and frame assembly are separated.
To remove the control panel, procedure as follows:
1. Disconnect the power supply cord and then remove
outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect connector CN-A, CN-E and CN-F from the
control unit.
5. Disconnect the wire leads from the relays RY1, RY2 and
RY3.
6. Remove one (1) screw holding the control panel back
plate to the chassis support.
7. Remove two (2) screws holding the bottom edge of the
back plate to the cabinet base.
8. Remove one (1) screw holding the back plate to the oven
cavity flange.
9. Lift up and pull the control panel assembly forward.
Replacement of individual component is as follows;
NOTE; 1. Before attaching a new key unit, remove remaining
adhesive on the control panel frame surfaces
completely with a soft cloth soaked in alcohol.
2. When a attaching the key unit to the control
panel frame, adjust the lower edge and right
edge of the key unit to the correct position of the
control panel frame.
3. Stick the key unit firmly to the control panel
frame by rubbing with soft cloth not to scratch.
FAN MOTOR REMOVAL
1. Disconnect the power supply cord and then remove
outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the wire leads from the fan motor.
5. Remove one (1) screw holding the fan motor grounding
wire to the air guide (Right).
6. Remove three (3) screws holding the chassis support to
the rear cabinet, waveguide and control panel back plate.
7. Remove the chassis support from the oven.
8. Remove one (1) screw holding the magnetron air guide
to the waveguide.
9. Remove the magnetron air guide from the waveguide.
10.Disconnect wire leads from the fan motor.
11. Release the main harness from the hole of the fan duct.
12. Release the thermistor harness from the hole of the fan
duct.
13. Release one (1) tab holding the fan duct to the rear
cabinet.
14. Release one (1) tab holding the fan duct to the air guide
(Right).
15.Remove the fan duct assembly from the oven.
34
R-930CS
3. Hold the center of the bracket which supports the shaft
of the fan motor on the flat table.
4. Apply the screw lock tight into the hole (for shaft) of the
fan blade.
5. Install the fan blade to the shaft of fan motor by pushing
the fan blade with a small, light weight, ball peen hammer
or rubber mallet.
CAUTION:
* Do not hit the fan blade strongly when installed
because the bracket may be disfigured.
* Make sure that the fan blade rotates smooth after
installation.
* Make sure that the axis of the shaft is not slanted.
6. Reset the fan duct assembly to its place.
7. Install the tabs of fan duct to the rear cabinet and air
guide.
8. Install the magnetron air guide with the one (1) screw.
9. Reinstall the main harness and thermistor harness to
each hole of the fan duct.
10.Reinstall the chassis support to the control panel back
plate, waveguide and rear cabinet with the three (3)
screws.
11.Re-connect the wire leads to the fan motor, referring to
the pictorial diagram.
12.Re-install the fan motor grounding wire to the air guide
(Right) with one (1) screw.
16.Remove the fan blade from the fan motor shaft according
the following procedure.
17.Hold the edge of the rotor of the fan motor by using a pair
of grove joint pliers.
CAUTION:
* Make sure that no metal pieces enter the gap
between the rotor and the stator of the fan motor
because the rotor is easily shaven by pliers and
metal pieces may be produced.
* Do not touch the pliers to the coil of the fan motor
because the coil may be cut or injured.
* Do not disfigure the bracket by touching with the
pliers.
18.Remove the fan blade from the shaft of the fan motor by
pulling and rotating the fan blade with your hand.
19. Now, the fan blade will be free.
CAUTION:
* Do not reuse the removed fan blade because the
hole (for shaft) may be larger than normal.
20.Remove the two (2) screws and nuts holding the fan
motor to the fan duct.
21.Now, the fan motor is free.
INSTALLATION
1. Install the fan motor to the fan duct with the two (2)
screws and nuts.
2. Install the fan blade to the fan motor shaft according the
following procedure.
Shaft
Coil
Groove joint pliers
Table
Shaft
Axis
Stator
Gap
Bracket
Rear View
These are the positions
that should be pinched
with pliers
Stator
Rotor
Side View
Center of
bracket
Rotor
DOOR SENSING SWITCH/SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH REMOVAL
At this time switch lever will be free, do not lose it.
Re-install
1. Re-install switch lever and each interlock switch in its
place. The secondary interlock switch is in the lower
position and the door sensing switch is in the upper
position and the monitor switch is in the middle position.
2. Re-connect wire leads to each switches and fuse holder.
Refer to pictorial diagram.
3. Secure latch hook (with two (2) mounting screws) to
oven flange.
4. Make sure that the monitor switch is operating properly
and check continuity of the monitor circuit. Refer to
chapter "Test Procedure" and Adjustment procedure.
1. Disconnect the power supply cord and then remove
outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Remove the control panel assembly, refer to "Control
Panel Removal".
5. Disconnect wire leads from each of the switches and
fuse holder.
6. Remove two (2) screws holding latch hook to oven
flange.
7. Remove latch hook assembly from oven flange.
8. Push outward on the one (1) stopper tabs holding each
of switches place.
9. Switch is now free.
DOOR SENSING SWITCH/SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH ADJUSTMENT
3. Discharge high voltage capacitor.
If the door sensing switch, secondary interlock switch and
monitor switch do not operate properly due to a
1. Disconnect the power supply cord and then remove
outer case.
2. Open the oven door and block it open.
35
R-930CS
misadjustment, the following adjustment should be made.
4. Loosen the two (2) screws holding latch hook to the oven
cavity front flange.
5. With door closed, adjust latch hook by moving it back and
forth, and up and down. In and out play of the door
allowed by the latch hook should be less than 0.5mm.
6. Secure the screws with washers firmly.
DOOR SENSING
SWITCH
MONITOR FUSE
After adjustment, check the following.
1. In and out play of door remains less than 0.5mm at the
latched position.
2. The door sensing switch and secondary interlock switch
interrupt the circuit before the door can be opened.
3. Monitor switch contacts close when door is opened.
4. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
MONITOR SWITCH
SECONDARY
INTERLOCK
SWITCH
Figure C-4. Latch Switch Adjustments
DOOR REPLACEMENT AND ADJUSTMENT
REMOVAL
1. Disconnect the power supply cord and then remove
outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Remove turntable tray and turntable support from oven
cavity.
5. Remove three (3) screws holding lower oven hinge.
6. Remove the lower oven hinge from oven cavity bottom
flange.
7. Remove door assembly from upper oven hinge on the
oven.
8. Door assembly is now free.
latch holes and that latch head goes through center of
latch hole.
2. Deviation of door alignment from horizontal line of cavity
face plate is to be less than 1.0mm.
3. Door is positioned with its face pressed toward cavity
face plate.
4. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
Note: The door on a microwave oven is designed to act as
an electronic seal preventing the leakage of
microwave energy from oven cavity during cook
cycle. This function does not require that door be
airtight, moisture (condensation)-tight or light-tight.
Therefore, occasional appearance of moisture, light
or sensing of gentle warm air movement around
oven door is not abnormal and do not of themselves
indicate a leakage of microwave energy from oven
cavity. If such were the case, your oven could not
be equipped with a vent, the very purpose of which
is to exhaust the vapor-laden air from the oven
cavity.
Note:
When the individual parts are replaced, refer to
"Door Disassembly".
9. On re-installing door, insert the upper oven hinge into the
door hinge pin. Then while holding door in place.
10.Make sure the door is parallel with oven face lines (left
and upper side lines) and door latch heads pass through
latch holes correctly.
11.Insert the lower oven hinge into oven cavity bottom
flange and then engaged the door hinge pin. Then
secure the lower oven hinge firmly with tree (3) mounting
screws.
Note: After any service to the door;
(A) Make sure that door sensing switch and secondary
interlock switch are operating properly. (Refer to
chapter "Test Procedures".).
(B) An approved microwave survey meter should be
used to assure compliance with proper microwave
radiation emission limitation standards.
UPPER OVEN HINGE
RE-INSTALL
DOOR ASSEMBLY
LATCH
HEADS
DOOR ADJUSTMENT
The door can be adjusted by keeping screws of each hinge
loose.
LOWER OVEN HINGE
RE-INSTALL
After adjustment, make sure of the following :
1. Door latch heads smoothly catch latch hook through
Figure C-5. Door Replacement and adjustment
36
R-930CS
DOOR DISASSEMBLY
DOOR PANEL
5. Remove the twelve (12) screws holding the door panel
to the door frame.
NOTE: The one (1) screw of the twelve (12) screws also
holds the earth terminal of the door decoration to the
door frame.
6. Remove the door panel from the door frame. Now the
door panel is free.
Remove door assembly, refer to "Door Replacement".
Replacement of door components are as follows:
CHOKE COVER
1. Place door assembly on a soft cloth with latches facing
up.
Note: As the engaging part of choke cover and door panel
are provided at several places, do not force any particular
part.
2. Insert an putty knife (thickness of about 0.5mm) into the
gap between the choke cover and corner portion of door
panel as shown Figure C-6 to free engaging parts.
3. Lift up choke cover.
4. Now choke cover is free from door panel.
DOOR GLASS
7. Remove the two (2) screws holding the thermal plate U
to the door frame.
8. Remove the two (2) screws holding the thermal plate R
to the door frame.
9. Remove the thermal plate U and the thermal plate R from
the door frame.
10.Slide the door glass leftward.
11.Slide the door glass upward.
12.Remove the door glass from the door frame. Now the
door glass is free.
2 LIFT UP
PUTTY KNIFE
1 BENT
CHOKE COVER
Door Bent
Panel
INSIDE Choke
cover
Upper
DOOR DECORATION AND DOOR FRAME
13.Straighten all tabs of the door decoration.
14.Remove the door decoration from the door frame.
15.Now the door decoration and door frame are free.
Lower
FRONT
Figure C-6. Door Disassembly
37
1
2
3
38
4
CN-A
RY6
T1
RED
BRN
BLK
ORG
ORG
BRN
BRN
5
1
2
3
4
5
6
7
8
9
WHT
PPL
BRN
ORG
CN-A
RY1 (N.O.)
RY1 (COM.)
RY2 (N.O.)
RY2 (COM.)
RED
COM
SECONDARY
INTERLOCK
SWITCH
6
GRY
GRY
TURNTABLE
MOTOR
PNK
GRY
G
R
Y
G
R
Y
BRN
GRY
CONVECTION MOTOR
Figure S-1. Pictorial Diagram
RED 2 RED
RED 1 RED
THERMISTOR
R
E
D
HEATING
ELEMENT
ORG
W W
H H
T T
P
P
L
BLK
RED
OVEN
THERMAL
CUT-OUT
PNK
GRY
N
GRN
POWER SUPPLY CORD
120V 60Hz
H
NOTE:
The grounding conductor of
the power supply cord has
been grounded by power
supply cord fixing screw.
The screw must be kept
allways tight.
COOLING
FAN
MOTOR
NOTE:
Hot (ORG) wire must be connected to the
power transformer terminal nearest to the
transformer mounting screw.
NOTE:
The neutral (GRY) wire
must be connected to
the terminal with "N"
mark on the power
supply cord.
G
R
Y
5
WHT
N.O. WHT
COM
ORG
WHT
WHT
WHT
DAMPER
MOTOR
W
H
T
POWER TRANSFORMER
HIGH VOLTAGE
CAPACITOR
HIGH
VOLTAGE
WIRE B
4
7
9
1
3
5
RY4
RY5
RY1
COM.
RY2
RY3 (N.O.)
RY3 (COM.) BRN
RED
GRN
ORG
PNK
RED
GRY
COM
N.O. DAMPER
SWITCH
PNK
PNK
ORG
MAGNETRON
3
N.O.
N.O.
COM.
RY3
CN-E
6
5
4
3
2
1
5
4
3
2
1
6 PNK
MONITOR
SWITCH
N.C.
BLUE MARK
PNK
RED
D
COM.
CN-F
G
CN-E
PNK
NOTE:
Hot (YLW & PNK) wire
must be connected to the
terminal with blue mark
on the oven light socket.
GRY
WHT
RED
2
1
3
IC-1
MONITOR FUSE
& FUSE HOLDER
BLK
GRN
ORG
F
COM
GRN
GRN
BLK
HIGH VOLTAGE COMPONENTS
1
N.O.
CN-G
H
N.O.
DOOR
SENSING
SWITCH
E
OVEN LAMP
& SOCKET
C
MAGNETRON
TEMPERATURE
FUSE
B
CONTROL PANEL
AH SENSOR
A
CN-F
1 BLK
2 RED
3 WHT
R-930CS
6
A
B
C
D
E
F
G
H
3
39
OVEN LAMP
TURNTABLE
MOTOR
HEATING
ELEMENT
A5
A3
A1
NO
4
COM
NO
COM
NO
COM
POWER
TRANSFORMER
FAN
MOTOR
CONV.
MOTOR
DAMPER
MOTOR
A7
c
RY1
RY3
RY2
RY6
RY5
D2
D3
C22 0.1µ/50v
(J1)
10G471K
RY4
4
D23
C2 1000µ/35v
C1 0.1µ/50v
+
–
Q22
KRA101M
Q21
KRA101M
Q20
KRA101M
R3 330 1/2w
Q1
2SB1238
5
C11
C3 0.1µ/50v
E2
C50
6
Q3
KRA101M
R8 4.7k
E4
OVEN
THERMISTOR
E3
R62 27kF
F1
(A)
(C)
F3
AH SENSOR
F2
(B)
CF1 4.19MHz
VCC 1
VEE
AVSS
VREF
AN7
AN6
AN5
AN4
AN3
AN2 10
AN1
AN0
P55
P54
P53 15
P52
P51
P50
P47
P46 20
P45
P44
P43
P42
INT1 25
P40
RST
XCIN
XCOUT
XIN 30
XOUT
VSS 32
R90 100k
P30
P31
P32
P33
P34
P35
P36
P37
P00
P01
P02
P03
P04
P05
P06
P07
P10
P11
P12
P13
P14
P15
P16
P17
P20
P21
P22
P23
P24
P25
P26
P27
C70 330pF x 4
33
35
40
45
50
55
60
64
1
Q90
KRA101M
(VP)
C10 0.1µ/50v
Figure S-2. Control Panel Circuit
DAMPER
SWITCH
E6
C60
Q40
KRA101M
C5 0.1µ/50v
R51 4.7k
E5
–
Custom
Help
G2
G1
KEY UNIT
Slow
Cook
Sensor
Reheat
G3
Low Mix
Bake
Convec
Preheat
Popcorn
G4
G7
Sensor
Cook
G6
Compu
Defrost
(A)
(VP)
SENSOR
DEFROST
MIX CONV
G5
(B)
12
R100 330 1w
Minute
Plus
(C)
IC2 IZA495DR
F 31, 32
F
1, 2
8G
29
NOTE
LBS
OZ
KG
Kitchen
Timer
Clock
Power
Level
9
8
400˚F
7
375˚F
6
350˚F
300˚F
275˚F
150˚F
100˚F
HELP
G12
450˚F
Stop
Clear
Start
Touch On
0
325˚F
5
High Mix
Roast
425˚F
4
Broil
3
2
1
G11
G10
Compu
Bake
G9
Compu
Roast
Compu
Broil
G8
COOK
FLUORESCENT DISPLAY TUBE
: IF NOT SPECIFIED. 1SS270A
: IF NOT SPECIFIED. 0.01µ/16v
: IF NOT SPECIFIED. 1/4w ± 5%
5
DOOR
SWITCH
E1
R31 4.7k
C30
Q23
KRA101M
+
–
R4 750 1/2w
–
+
Q4
DTA123ES
4
D30
Q26
KRC243M
Q25
KRA101M
Q24
KRA101M
–
ZD2
470 1/2w
+
(J2)
HZ16-1
SP40
C4 10µ/35v
R40 3.3k
C21 0.1µ/50v
HZ5C2
C9 0.01µ/50v
22µ
/25v
ZD3
R50 15k
R2
C20 10µ/35v
ZD4
+
(J4) 6.8k
C6 10µ/35v
(J3)
VRS1
a
(J6)
HZ4A2
R63 220F
b
(J7)
D4
R7 4.7k
D1
C7
5
(J5) 15k
3
IC1 IZA797DR
d
C8
R64 3.3kF
R11 18 1w
R70 3.3k
R10 18 1w
R71 3.3k
CONTROL UNIT
R72 3.3k
+
R73 3.3k
D1-4 : 11ES1
28
27
–
26
7G
6G
D7
25
24
5G
AC120V
60Hz
7
P16 20
8
100k
R92
D20
D21
D22
D24
D25
D26
100k
R91
D70 R74
3.3k
100k
R93
23
22
4G
3G
D72 R76
3.3k
T1
P12 16
1
3
R30 15k
P15 19
P14 18
P13 17
D73 R77
3.3k
2G
1G
D71 R75
3.3k
2
D31
P11 15
P10 13
P9 12
2
D75 R79
3.3k
1
9
H
11
10
G
P8
P7
F
P6
E
D76 R80
3.3k
D
8
7
6
5
4
C
P5
P4
B
D74 R78
3.3k
A
P3
P2
P1
1
D77 R81
3.3k
A9
R-930CS
6
A
B
C
D
E
F
G
H
R-930CS
1
2
4
3
5
6
A
A
R
1
32
DIP
,F
B
B
E
3
R90
C70
C10
(C81)
R86(J8)
(ONLY
PHR)
(CF1)
32
33
CF1
(R85)
D70
D71
D72
D73
D74
D75
D76
D77
1
(C80)
(R45)
(C45)
C7
R7
R8
C8
3
C
E
E
5
B
Q4
B
Q3
1
12
R79
R78
R77
R76
R75
6
C9
R64
64
9
C5
4
D
(C47)
IC3
1
8
3
14
R40
1
CN - F
15
16
17
18
6
R31
R30
E
B
Q24 E
1
B
C3
D31
D30
C4
E
Q1
D23
RY2
B
E
E
D21
D3
D4
D1
B
D20
4
1
S1
1
5
P
VRS1
3
5
7
DAMP M CONV M FAN M
RY4
E
Q22
25
Q20
F
D2
E
BE
Q26
23
24 B
C1
C20
BLK
C22
B
Q21
RY5
21
C2
22
ZD2
D26
R2
B Q23
20
RY1
POWER
PINK RED (BRN
OL TTM
RED)
R3
E
DOOR
SW
Q25
3 2
B
CN - E
ORG
POWER TRANS
19
E
D24
OVEN
TEMP
R62
C21
E
5 4
R63
R50
R51
Q40
DAMP
SW
R4
D25
F
5
1
C30
C50
C60
13
BRN
RY3
(R49)
(C46)
C6
(R46)
CN - G
IC2
10
11
12
(J7)
(J5)
(J3)
(J2)
(J4)
(J6)
CONV
HEATER COM
RED
(R47)
(R48)
1
8
R100
12
D
ZD3
ZD4
7
12
R74
S2
3
8
9
D7
26
POWER
G
T1
(J1)
7
G
1
(CN - D)
4
IC1
(CN - G)
(ONLY 9X58PJ)
C
R91
R92
R93
R80
R81
R73
R72
R71
R70
B
Q90
1
2
CN - A
D22
C11
R10
RY6
R11
0
H
H
Figure S-3. Printed Wiring Board
1
2
4
3
40
5
6
R-930CS
PARTS LIST
Note: The parts marked "∆" may cause undue microwave exposure.
The parts marked "*" are used in voltage more than 250V.
REF. NO.
PART NO.
DESCRIPTION
Q'TY
CODE
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AN
AT
AH
AF
AG
AK
AN
AK
AG
AL
AS
AK
AG
AZ
AZ
AW
BL
BP
AX
AV
AP
BL
AY
AY
1
1
1
1
1
4
1
1
1
1
1
1
BK
AC
AM
AB
AA
AD
AH
AG
AG
AF
AM
AE
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
4
1
BU
AC
AC
AD
AF
AY
AG
AA
AF
AA
AA
AA
AA
AA
AB
AA
AA
AA
AM
AA
AA
AA
AA
AE
AG
AB
AA
ELECTRICAL PARTS
*
*
*
*
*
∆*
1- 1
1- 1
1- 2
1- 3
1- 4
1- 4
1- 5
1- 6
1- 7
1- 8
1- 9
1-10
1-11
1-13
1-14
1-15
1-16
1-16
1-17
1-17
1-18
1-19
1-20
1-21
FACCDA075WRE0
FACCDA048WRE0
FFS-BA012WRK0
QFSHDA009WRE0
QSW-MA131WRE0
QSW-MA110WRE0
FH-HZA041WRE0
QSW-MA110WRE0
QFS-TA013WRE0
RTHM-A085WRE0
RMOTDA192WRE0
RLMPTA071WRE0
QSOCLA021WRE0
RMOTEA283WRE0
RMOTEA300WRE0
RHET-A136WRE0
RTRN-A535WRE0
RTRN-A527WRE0
RC-QZA173WRE0
RC-QZA211WRE0
FH-DZA053WRK0
RV-MZA256WRE0
RMOTDA222WRE0
FDTCTA183WRK0
Power supply cord
Power supply cord (Interchangeable)
Monitor fuse 20A and monitor switch (V-5220D-070) assembly
Fuse holder
Secondary interlock switch & door sensing switch
Secondary interlock switch & door sensing switch (Interchangeable)
Thermistor
Damper aswitch
Magnetron temperature fuse 150˚C
Oven thermal cut-out 150˚C
Damper motor
Oven lamp
Oven lamp socket
Convection fan motor
Fan motor
Heating element
Power transformer
Power transformer (Interchangeable)
H.V.capacitor
H.V.capacitor (Interchangeable)
H.V.rectifier assembly
Magnetron
Turntable motor
AH sensor assembly
2- 1
2- 2
2- 3
2- 3-1
2- 3-2
2- 4
2- 5
2- 6
2- 7
2- 8
2- 9
2-10
GCABUA728WRP0
TMAPCA763WRR0
FDAI-A198WRY0
GCOVHA156WRP0
XHTSD40P08RV0
GLEGPA019WRE0
GCABDA095WRW0
LHLDKA009WRF0
LBNDKA036WRP0
FHNG-A092WRM0
PHOK-A112WRF0
MLEVPA231WRF0
Outer case cabinet
Schematic diagram
Base cabinet
Turntable motor cover
Screw; 4mm x 8mm
Foot
Rear cabinet
Cord holder
Capacitor holder
Oven hinge (Lower)
Latch hook
Switch lever
CABINET PARTS
∆
∆
CONTROL PANEL PARTS
3- 1
3- 1A
3- 1B
3- 1C
3- 1D
3- 1E
3- 1F
C1
C2
C3
C4
C5
C6
C7-8
C9
C10
C11
C20
C21
C22
C30
C50
C60
C70
CF1
D1-4
D7
CPWBFA748WRK0
QCNCMA227DRE0
QCNCMA267DRE0
QCNCMA237DRE0
QCNCWA057DRE0
RV-KXA077DRE0
PCUSGA381WRP0
RC-KZA087DRE0
VCEAB31VW108M
RC-KZA087DRE0
VCEAB31VW106M
RC-KZA087DRE0
VCEAB31VW106M
VCKYD11CY103N
VCTYF31HF103Z
RC-KZA087DRE0
VCEAB31EW226M
VCEAB31VW106M
VCEAB31HW104M
RC-KZA087DRE0
VCKYD11CY103N
VCKYD11CY103N
VCKYD11CY103N
RMPTEA009DRE0
RCRS-A035DRE0
VHD11ES1///-1
VHD1SS270A/-1
Control unit
5-pin connector(A)
6-pin connector(E)
3-pin connector(F)
12-pin connector(G)
Fluorescent display tube
Cushion
Capacitor
0.1µF 50V
Capacitor 1000µF 35V
Capacitor
0.1µF 50V
Capacitor
10µF 35V
Capacitor
0.1µF 50V
Capacitor
10µF 35V
Capacitor 0.01µF 16V
Capacitor 0.01µF 50V
Capacitor
0.1µF 50V
Capacitor
22µF 25V
Capacitor
10µF 35V
Capacitor
0.1µF 50V
Capacitor
0.1µF 50V
Capacitor 0.01µF 16V
Capacitor 0.01µF 16V
Capacitor 0.01µF 16V
Capacitor array 330pF x 4
Ceramic resonator (CST4.19MGW)
Diode (11ES1)
Diode (1SS270ATA)
41
R-930CS
REF. NO.
D20-26
D30-31
D70-77
IC1
IC2
Q1
Q3
Q4
Q20-23
Q24-25
Q26
Q40
Q90
R2
R3
R4
R7-8
R10-11
R30
R31
R40
R50
R51
R62
R63
R64
R70-81
R90-93
R100
(J4)
(J5)
RY1-3
RY4-6
SP40
T1
VRS1
ZD2
ZD3
ZD4
3- 2
3- 2-1
3- 2-2
3- 2-3
3- 2-4
3- 2-5
3- 3
3- 4
3- 5
3- 6
3- 7
3- 8
PART NO.
VHD1SS270A/-1
VHD1SS270A/-1
VHD1SS270A/-1
RH-IZA797DRE0
RH-IZA495DRE0
VS2SB910MR/-4
VSKRA101M//-3
VSDTA123ES/-3
VSKRA101M//-3
VSKRA223M//-3
VSKRC243M//-3
VSKRA101M//-3
VSKRA101M//-3
VRD-B12HF471J
VRD-B12HF331J
VRD-B12HF751J
VRD-B12EF472J
VRS-B13AA180J
VRD-B12EF153J
VRD-B12EF472J
VRD-B12EF332J
VRD-B12EF153J
VRD-B12EF472J
VRN-B12EK273F
VRN-B12EK221F
VRN-B12EK332F
VRD-B12EF332J
VRD-B12EF104J
VRS-B13AA331J
VRD-B12EF682J
VRD-B12EF153J
RRLY-A083DRE0
RRLY-A078DRE0
RALM-A014DRE0
RTRNPA022DRE0
RH-VZA032DRE0
VHEHZ161///-1
VHEHZ5C2///-1
VHEHZ4A2///-1
DPNLCB575WRK0
FUNTKA958WRE0
JBTN-B110WRF0
MSPRCA050WRE0
GCOVAA274WRP0
GMADIA110WRF0
LANGTA340WRW0
MLEVFA057WRW0
NSFTTA042WRE0
XEPSD30P10XS0
XCPSD40P12000
XOTSD40P12RV0
DESCRIPTION
Diode (1SS270ATA)
Diode (1SS270ATA)
Diode (1SS270ATA)
LSI
IC
Transistor (2SB910M)
Transistor (KRA101M)
Transistor (DTA123E)
Transistor (KRA101M)
Transistor (KRA223M)
Transistor (KRC243M)
Transistor (KRA101M)
Transistor (KRA101M)
Resistor 470 ohm 1/2W
Resistor 330 ohm 1/2W
Resistor 750 ohm 1/2W
Resistor 4.7k ohm 1/4W
Resistor
18 ohm 1W
Resistor 15k ohm 1/4W
Resistor 4.7k ohm 1/4W
Resistor 3.3k ohm 1/4W
Resistor 15k ohm 1/4W
Resistor 4.7k ohm 1/4W
Resistor 27k ohm(F) 1/4W
Resistor 220 ohm(F) 1/4W
Resistor 3.3k ohm(F) 1/4W
Resistor 3.3k ohm 1/4W
Resistor 100k ohm 1/4W
Resistor 330 ohm 1W
Resistor 6.8k ohm 1/4W
Resistor 15k ohm 1/4W
Relay (OMIF-S-118LM)
Relay (OJ-SH-118LM)
Buzzer (PKM22EPT)
Transformer
Varistor (10G471K)
Zener diode (HZ16-1)
Zener diode (HZ5C-2)
Zener diode (HZ4A2)
Control panel frame with key unit
Key unit
Open button
Open button spring
C/P decoration
Display window
Control panel back plate
Open lever
Open shaft
Screw ; control unit mtg.
Screw ; control panel back plate mtg.
Screw ; 4mm x 12mm
Q'TY
7
2
8
1
1
1
1
1
4
2
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
12
4
1
1
1
3
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
3
1
CODE
AA
AA
AA
AX
AL
AE
AB
AA
AB
AB
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AK
AG
AG
AN
AE
AA
AA
AA
BD
AW
AF
AB
AR
AF
AK
AE
AE
AA
AA
AA
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
-AL
AT
AQ
AR
AD
AB
AB
AE
AC
AT
AK
AE
AF
AG
BB
AC
AB
AM
AK
AC
OVEN PARTS
∆
4- 1
4- 2
4- 3
4- 4
4- 5
4- 6
4- 7
4- 8
4- 9
4-10
4-11
4-12
4-13
4-14
4-15
4-16
4-17
4-18
4-19
4-20
4-21
*************
FROLPA072WRK0
NTNT-A019WRH0
FBRGMA002WRE0
PREFHA028WRW0
LANGTA196WRW0
LBNDK0054WRE0
LFIX-A013WRW0
NFANMA019WRW0
NPLYBA020WRF0
FDUC-A279WRK0
PFPF-A138WRE0
LANGKA723WRP0
PCUSUA167WRP0
PCUSUA424WRP0
FDUC-A322WRW0
MCAMPA030WRF0
NSFTTA114WRE0
FFTA-A034WRK0
PDUC-A269WRW0
PCUSGA398WRP0
Oven cavity assembly (Not a replaceable part)
Turntable support
Turntable tray
Bearing ass’y
Thermal protection plate (left)
Bearing mounting plate
Heater element holder
Bearing holder plate
Convection fan
Pulley (F)
Heater duct assembly
Thermal protection sheet (left)
Glass mounting plate
Cushion
Cushion
Steam duct assembly
Damper cam
Damper shaft
Damper door ass’y
Damper duct
Cushion
42
R-930CS
PART NO.
NCPL-A021WRF0
PCOVPA301WRE0
PCUSUA197WRP0
PGLSPA455WRE0
PFPF-A139WRE0
PREFHA053WRW0
PSKR-A153WRW0
PSKR-A323WRW0
LANGQA407WRW0
NPLYBA021WRF0
NFANJA020WRE0
PDUC-A270WRF0
LANGFA089WRW0
MHNG-A165WRM0
NBLTKA005WRE0
PFPF-A064WRE0
PCUSUA196WRP0
PCUSUA425WRP0
PCUSGA353WRP0
PSKR-A171WRW0
DESCRIPTION
Turntable coupling
Waveguide cover
Cushion
Light glass
Thermal protection sheet (Right)
Thermal protection plate (Right)
Air guide (Bottom)
Air guide (Right)
Convection motor mounting plate
Pulley (M)
Fan blade
Cooling fan duct
Chassis support
Oven hinge (Upper)
Convection fan belt
Thermal protection sheet
Cushion
Damper duct cushion
Cushion
Magnetron air guide
∆
∆
5
5- 1
5- 2
5- 3
5- 4
5- 5
5- 6
5- 7
5- 8
5- 9
5-10
5-11
5-12
5-13
CDORFA844WRK0
DDORFA820WRY0
PGLSPA534WRE0
GCOVHA155WRF0
GWAKPA665WRF0
GCOVAA273WRP0
LANGKA851WRT0
LSTPPA169WRF0
MSPRTA192WRE0
LANGKA918WRW0
LANGKA919WRW0
XCPSD40P08000
XEBSD30P08000
PCUSGA537WRPZ
Door panel assembly complete
Door panel
Door glass
Choke cover
Door frame
Door decoration
Latch angle
Latch head
Latch head spring
Thermal plate U
Thermal plate R
Screw; 4mm x 8mm
Screw; 3mm x 8mm
Cushion
*
6- 1
6- 2
6- 3
6- 4
6- 5
6- 6
6 -7
6- 8
6- 9
6-10
6-11
FAMI-A088WRM0
FAMI-A087WRM0
TCADCA522WRR0
FW-VZB342WRE0
FW-VZB668WRE0
QW-QZA198WRE0
QW-VZA108WRE0
TCAUAA240WRR0
TCAUAA200WRR0
TCAUAA209WRR0
TINSEA815WRR0
Low rack (Broiling trivet)
High rack (Baking rack)
Cook book
Thermistor harness
Main wire harness
High voltage wire B
Grounding wire (Cooling fan motor)
Screw caution label
Monitor caution label
DHHS caution label
Operation manual
∆
REF. NO.
4-22
4-23
4-24
4-25
4-26
4-27
4-28
4-29
4-30
4-31
4-32
4-33
4-34
4-35
4-36
4-37
4-38
4-39
4-40
4-41
Q'TY
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
CODE
AE
AE
AD
AD
AF
AP
AK
AF
AG
AC
AE
AL
AE
AE
AF
AF
AD
AG
AH
AE
1
1
1
1
1
1
1
1
1
1
1
6
12
1
BS
BD
AZ
AP
AX
BA
AF
AH
AC
AH
AF
AA
AA
AD
1
1
1
1
1
1
1
1
1
1
1
AW
AW
BA
AN
AZ
AN
AF
AC
AB
AD
AG
14
4
2
1
2
1
1
6
1
2
7
7
1
2
1
6
3
2
2
1
4
6
2
AA
AA
AA
AA
AA
AA
AA
AC
AA
AA
AA
AA
AA
AA
AB
AA
AA
AC
AC
AA
AA
AA
AB
DOOR PARTS
∆
∆
∆
MISCELLANEOUS
SCREWS NUTS AND WASHERS
7- 1
7- 2
7- 3
7- 4
7- 5
7- 6
7- 7
7- 8
7- 9
7-10
7-11
7-12
7-13
7-14
7-15
7-16
7-17
7-18
7-19
7-20
7-21
7-22
7-23
XOTWW40P10000
XOTSE40P12000
XCTWW40P08000
XHTSD40P08RV0
LX-CZ0052WRE0
XWVSD60-07000
LX-WZA004WRE0
LX-CZA074WRE0
XBPSD30P14K00
XBPSD40P25000
XBTWW40P06000
XCTSD40P08000
XCPSD40P10000
XBPSD40P06KS0
LX-WZA022WRE0
XCPSD40P08000
XCPSD30P06000
LX-CZA070WRE0
XHPSD40P08K00
XHTSD40R12RV0
XCBWW30P06000
XFPSD40P08000
XFPSD60P14JS0
Screw; 4mm x 10mm
Screw; 4mm x 12mm
Screw; 4mm x 8mm
Screw; 4mm x 8mm
Special screw
Washer; 6mm x 0.7 mm
Washer
Special screw
Screw; 3mm x 14mm
Screw; 4mm x 25mm
Screw; 4mm x 6mm
Screw; 4mm x 8mm
Screw; 4mm x 10mm
Screw; 4mm x 6mm
Washer
Screw; 4mm x 8mm
Screw; 3mm x 6mm
Special screw (Torx tamper proof screw)
Screw; 4mm x 8mm
Screw; 4mm x 12mm
Screw; 3mm x 6mm
Screw; 4mm x 8mm
Screw; 6mm x 14mm
43
R-930CS
REF. NO.
7-24
7-25
7-26
7-27
7-28
7-29
PART NO.
XOTSD40P12000
XHPSD30P08000
XNESD40-32000
XNEUW40-32000
XWSUW40-10000
XOTSD40P12RV0
DESCRIPTION
Q'TY
16
2
2
1
1
5
Screw; 4mm x 12mm
Screw; 3mm x 8mm
Nut; 4mm x 3.2mm
Nut; 4mm x 3.2mm
Washer; 4mm x 1mm
Screw; 4mm x 12mm
CODE
AA
AA
AA
AA
AA
AA
HOW TO ORDER REPLACEMENT PARTS
To have your order filled promptly and correctly, please furnish the following information.
1. MODEL NUMBER
3. PART NO.
2. REF. NO.
4. DESCRIPTION
Order Parts from the authrized SHARP parts Distributor for your area.
Defective parts required return should be returned as indicated in the Service Policy.
PACKING AND ACCESSORIES
TRAY HOLDER
(SPADFA348WRE0)
TOP PAD ASSEMBLY
FPADBA358WRK0
DOOR PROTECTION SHEET
4-3 TURNTABLE TRAY
SPADPA178WRE0
PLASTIC BAG
SSAKHA012WRE0
6-11 OPERATION
MANUAL
6-3 COOK BOOK
MICROWAVE OVEN
CABINET COVER
4-2 TURNTABLE SUPPORT
SPADPA507WRE0
BOTTOM PAD ASSEMBLY
FPADBA359WRK0
TRAY PACKING FOAM
SPADPA198WRE0
PACKING CASE
SPAKCD292WRE0
Not replaceable items.
44
H
1
2
4-30
4-31
1-5
3
45
4-2
4-3
4-9
4-22
4-35
4
2-8
5
7-24
1-20
4-28
7-5
2-10
A
2-4
x4
2-7
7-19
1-4
1-4
4-21
2-9
x3
7-16
7-22
1-7
7-24
4-26
4-38
4-14
1-17
7-24 x5
1-2
7-13
1-3
1-18
x2
7-4
x2
4-40
1-16
7-6
7-23
4-18
6-7
7-20
6-10
1-9
4-39
1-1
4-17
7-10
2-5
4-27
1-19
7-24
6-8
7-17
7-16
1-6
7-9
4-20
1-14
4-41
4-19
7-16
7-26
7-2
4-33
2-2
4-15
A
7-19
4-32
7-2
7-18
5
6
2-3-2
2-3-1
7-22
x2
7-7
7-16
6-4
2-6
7-2
4
7-24
7-8
x3
7-1
7-1
x9
4-29
7-16
x4
4-37
6-9
7-24 x 5
3
2-3
4-38
7-28
7-11
x3
4-1
7-27
4-24
7-8
6-7
7-12
7-24
C
4-23
TO OVEN
BASE PLATE
1-13
7-11
7-21
7-21
1-15
7-22
4-16
7-16
4-25
4-34
2
7-24
4-14
7-11
1-21
4-13
1-11
OVEN AND CABINET PARTS
7-14
x2
7-1
7-21 x2
4-7
4-11
4-12
F
1-8
7-15
7-12
x3
4-24
1-10
D
7-17
4-6
7-1
x3
7-25
E
4-4
G
4-5
7-18
A
4-8
x2
2-1
1
4-36
4-10
7-3
7-24
R-930CS
6
A
B
B
C
D
E
F
G
H
R-930CS
2
1
4
3
6
5
3-7
CONTROL PANEL PARTS
3-3
A
A
3-1
3-6
x3
3-4
3-2
7-24
B
B
3-8
3-2-5
3-2-4
3-5
3-7
3-2-1
7-24
C
C
DOOR PARTS
3-2-3
5
3-2-2
5-12
5-3
D
D
5-1
5-13
5-9 5-11
E
E
5-4
5-11
5-2
5-11
5-5
5-6
5-7
F
F
5-10
5-11
5-8
MISCELLANEOUS
6-5
G
6-1
6-2
G
6-4
Actual wire harness may be different than illustration.
6-6
H
H
6-7
1
2
4
3
5
6
'99 SHARP CORP. (9S2.530E) Printed in U.S.A
46
R-930CS
COPYRIGHT © 1999 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced, stored in retrieval systems, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
'99 SHARP CORP. (5S2.530E) Printed in U.S.A
26