Ariston FK 898E P X AUS S Operating instructions

FK 898E P X AUS S
FK 898E P AUS S
English
Operating Instructions
OVEN
Contents
Operating Instructions,1
Warnings,2
Assistance,3
Description of the appliance,4
Installation,5
Electrical Connection,6
Start-up and use,7
Modes,8
Precautions and tips,12
Maintenance and care,12
Troubleshooting,15
AUS
Warnings
WARNING: The appliance and its
accessible parts become hot during use.
Care should be taken to avoid touching
heating elements. Children less than 8
years of age shall be kept away unless
continuously supervised. This appliance
can be used by children aged from 8 years
and above and persons with reduced
physical, sensory or mental capabilities
or lack of experience and knowledge
if they have been given supervision
or instruction concerning use of the
appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and
user maintenance shall not be made by
children without supervision.
Do not use harsh abrasive cleaners or
sharp metal scrapers to clean the oven
door glass since they can scratch the
surface, which may result in shattering
of the glass.
Never use steam cleaners or pressure
cleaners on the appliance.
2
WARNING: Ensure that the appliance is
switched off before replacing the lamp
to avoid the possibility of electric shock.
Before initiating the automatic cleaning
cycle:
• clean the oven door;
• remove large or coarse food residues
from the inside of the oven using a damp
sponge. Do not use detergents;
• remove all accessories and the sliding
rack kit (where present);
• do not place tea towels
Keep children away from the appliance
during the automatic cleaning cycle as
surfaces may become very hot.
! When you place the rack inside, make
sure that the stop is directed upwards
and in the back of the cavity.
AUS
Assistance
! Never use the services of an unauthorised technician.
Please have the following information to hand:
• The type of problem encountered.
• The appliance model (Mod.).
• The serial number (S/N).
The latter two pieces of information can be found on the
data plate located on the appliance.
ARISTON
PRIORITY SERVICE
If you are not completely satisfied with your appliance or
require service call:
Australia
Phone: 1300 815 589
New Zealand
Phone: (09) 306 1020
GENUINE ACCESSORIES
& SPARE PARTS
A wide range of genuine
accessories are available for your appliance call:
Australia
Phone: 03 9768 0888
New Zealand
Phone: (09) 306 1020
AUSTRALIA
ARISIT PTY LIMITED
40-44 Mark Anthony Drive, Dandenong South,
VIC 3175, Australia
Fax: Service & Sales (03) 9768 0838
NEW ZEALAND
ARISIT PTY LIMITED
PO Box 68-140 Newton, Auckland
1145, New Zealand
Fax: (09) 302 0077
Email: consumer.care@arisit.com
Email: sales@aristonappliances.co.nz
3
AUS
Description of the appliance
Overall view
9
1.POSITION 1
2.POSITION 2
3.POSITION 3
4.POSITION 4
5.POSITION 5
6.GUIDES for the sliding racks
7.DRIPPING PAN
8.GRILL
9.Control panel
6
8
5
7
3
4
2
1
Control panel
Display
10. SELECTOR knob
11. CONTROL PANEL POWER BUTTON
12. DISPLAY
13. THERMOSTAT / TIMER knob
14. START / STOP
15. FAST CLEAN icon
16. MINUTE MINDER icon
17. TIMER icon
18. DOOR / CONTROL PANEL LOCK icon
19. LIGHT icon
20. TEMPERATURE and TIME numerical digits
21. DURATION icon
22. END OF COOKING icon
23. CLOCK icon
24. MINUTE MINDER icon
25. CONTROL PANEL LOCK indicator
26. DOOR LOCK indicator
27. Preheating / Residual heat indicator
28. MODE icons
10
12
11
18
19
13
15
14
17
16
28
4
20
21 22
27
26 25 24 23
Installation
! Please keep this instruction booklet in a safe place for
future reference. If the appliance is sold, given away or
moved, please make sure the booklet is also passed on to
the new owners so that they may benefit from the advice
contained within it.
Ventilation
To ensure adequate ventilation, the back panel of the
cabinet must be removed. It is advisable to install the oven
so that it rests on two strips of wood, or on a completely
flat surface with an opening of at least 45 x 560 mm (see
diagrams).
! Please read this instruction manual carefully: it contains
important information concerning the safe operation,
installation and maintenance of the appliance.
560
mm
.
45 m
m.
Positioning
! Do not let children play with the packaging material; it
should be disposed of in accordance with local separated
waste collection standards (see Precautions and tips).
! The appliance must be installed by a qualified professional
in accordance with the instructions provided. Incorrect
installation may damage property or cause harm to people
or animals.
Built-in appliances
Use an appropriate cabinet to ensure that the appliance
operates properly:
Centring and fixing
Secure the appliance to the cabinet:
• Open the oven door.
• slide out the side gaskets at the top until the 2 fixing holes
are exposed;
• Fix the oven to the cabinet using the 2 wood screws.
• reposition the 2 gaskets.
• The panels adjacent to the oven must be made of heatresistant material.
• Cabinets with a veneer exterior must be assembled with
glues which can withstand temperatures of up to 100°C.
m.
45 m
570 mm.
590 mm.
20 mm.
.
mm
550 in.
m
595
mm
.
560
mm
.
! All parts which ensure the safe operation of the appliance
must not be removable without the aid of a tool.
575-585 mm.
• To install the oven under the counter (see diagram) or
in a kitchen unit, the cabinet must have the following
dimensions:
.
mm
550
.
m
5 m .*
20, mm
5
,
2
2
* Stainless steel models only
! The appliance must not come into contact with electrical
parts once it has been installed.
The indications for consumption given on the data plate
have been calculated for this type of installation.
5
AUS
AUS
Electrical Connection
The electrical connection to the mains must be made on
the appliance. The power voltage and frequency are as
indicated on the rating plate.
! THIS APPLIANCE MUST BE EARTHED.
Fitting the power supply cable
L
N
1. Open the terminal board
by inserting a screwdriver
into the side tabs of the
cover. Use the screwdriver
as a lever by pushing it
down to open the cover (see
diagram)
.
2. Install the power supply
cable by loosening the
cable clamp screw and the
three wire contact screws
.
L-NConnect the wires to the
corresponding terminals:
the Blue wire to the terminal
marked (N), the Brown wire
to the terminal marked (L)
and the Yellow/Green wire
to the terminal marked
(see diagram).
3. Secure the cable by fastening the clamp screw.
4. Close the cover of the terminal board.
Connecting the supply cable to the mains
Install a standardised plug corresponding to the load
indicated on the data plate (see side).
The appliance must be directly connected to the mains
using an omnipolar circuit-breaker with a minimum contact
opening of 3 mm installed between the appliance and the
mains, suitable for the load indicated and complying with
current electrical regulations (the earthing wire must not be
interrupted by the circuit-breaker). The supply cable must
not come into contact with surfaces with temperatures
higher than 50°C.
! The installer must ensure that the correct electrical
connection has been made and that it is compliant with
safety regulations.
Before connecting to the power supply, make sure that:
• The appliance is earthed and the plug is compliant with
the law.
• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate (see
below).
• The voltage must be in the range between the values
indicated on the data plate (see below).
• The socket is compatible with the plug of the appliance.
If the socket is incompatible with the plug, ask an
authorised technician to replace it. Do not use extension
cords or multiple sockets.
6
! Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only (see Assistance).
! The manufacturer declines any liability should these safety
measures not be observed.
APPLIANCE SPECIFICATIONS
Dimensions*
width 43.5 cm
height 32,4 cm
depth 41.5 cm
Volume*
59 l
Dimensions**
width 45.5 cm
height 32,4 cm
depth 41.5 cm
Volume**
62 l
Electrical
connections
voltage: 220 - 240 V~ 50/60 Hz or
50 Hz (see data plate)
maximum power absorbed
2800 W
Directive 2002/40/EC on the label
of electric ovens. Standard EN 50304
ENERGY
LAB EL
Declared energy consumption
for Forced convection Class –
heating mode:
ECO.
This appliance conforms to the following
European Economic Community
directives:
- 2006/95/EEC dated 12/12/06 (Low
Voltage) and subsequent amendments.
- 2004/108/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments.
- 93/68/EEC dated 22/07/93 and
subsequent amendments.
- 2012/19/EC and subsequent
amendments.
- 1275/2008 standby/off mode.
* Only for models with drawn rails.
** Only for models with wire rails.
Start-up and use
Setting the clock
WARNING! The oven is
provided with a stop system
to extract the racks and
prevent them from coming
out of the oven (1).
As shown in the drawing,
to extract them completely,
simply lift the racks, holding
them on the front part, and pull (2).
the oven is in standby mode, pressing the
button once will
display the current time setting. Press it again to set the time.
! The first time you use your appliance, heat the empty oven
with its door closed at its maximum temperature for at least
half an hour. Make sure that the room is well ventilated
before switching the oven off and opening the oven door.
The appliance may emit a slightly unpleasant odour caused
by protective substances used during the manufacturing
process burning away.
! To make the setting process easier, keep the knob in
“ ” and “ ” position: this will increase the scrolling speed
of the numbers on the display.
! Each setting will automatically be stored in the appliance
memory after 10 seconds.
! The touch controls cannot be activated if the user is
wearing gloves.
! In order to optimise the cooking performance, when
starting the selected function, product settings will be
applied that could cause a delayed start of the fan and
heating elements.
Some models are equipped with a system of hinges which
allows the door to close slowly, without the user having to
follow the movement through with his/her hand. To use the
system correctly, before closing the door:
• Open the door fully.
• Do not force the closing movement manually.
After connection to the power supply network or after
a blackout, the
button and the digits on the TIME display
will flash for 10 seconds.
To set the clock:
1. Press the
button.
2. Turn the TIMER knob towards “ ” and “ ” to adjust the
hour value.
3. Once you have reached the correct hour value, press
the
button.
4. Repeat the above process to set the minutes.
If a blackout occurs, it will be necessary to reset the clock.
If the
icon flashes on the display, this indicates that the
clock has not been set correctly.
Setting the minute minder
! The minute minder may be set regardless of whether the
oven is switched on or off. It does not switch the oven on or off.
When the set time has elapsed, the timer emits a buzzer
that will automatically stop after 30 seconds or when any
active button on the control panel is pressed.
To adjust the timer proceed as follows:
.
1. Press button
2. Turn the TIMER knob towards “ ” and “ ” to adjust the
hour value.
3. Once you have reached the desired value, press the
button again.
symbol will remind you that the minute minder
The lit
is on. The DISPLAY will show the countdown.
To cancel the minute minder, press the
Control panel lock
! The control panel can be locked while the oven is off, once
cooking has started or finished and during programming.
button for
To lock the oven controls, press and hold the
at least 2 seconds. A buzzer sounds and the display shows
the key symbol “n—O”. The
and
icons, when lit,
indicate lock function activation.
To deactivate the lock, press and hold the
button again
for at least 2 seconds.
! When cleaning the appliance, the door lock may be closed
accidentally (there is an exposed spring). If this happens,
reopen it by turning the door lock upwards (see figure).
KO
! The clock can only be set when the oven is switched off. If
OK
button and use
the knob to set the time to 00:00. Press button
again.
The
icon will switch off to indicate that the minute minder
has been disabled.
Starting the oven
1. Switch the control panel on by pressing the
button.
The appliance buzzer sounds three times (ascending) and
all buttons light up in sequence.
2. Select the desired cooking mode by turning the
SELECTOR knob. The display shows:
- the temperature associated with the mode, if programming
manually;
- “Auto” and the duration alternately, if programming is
automatic.
button to begin cooking.
3. Press the
4. The oven will begin its preheating phase, the preheating
indicators will light up as the temperature rises.
5. When the preheating process has finished, a buzzer
sounds and all the preheating indicator lights show that this
stage has been completed: the food can then be placed in
the oven.
7
AUS
AUS
6. During cooking it is always possible to:
- modify the temperature by turning the THERMOSTAT
knob (manual modes only);
- set the duration of a cooking mode (see Cooking Modes);
button to stop cooking. In this case the
- press the
appliance stores the temperature modified previously in its
memory (manual modes only);
-
switch off the oven by pressing the
button for
3 seconds..
7. If a blackout occurs while the oven is already in operation,
an automatic system within the appliance will reactivate the
cooking mode from the point at which it was interrupted,
provided that the temperature has not dropped below a
certain level. Programmed cooking modes which have not
yet started will not be restored and must be reprogrammed
(for example: a cooking mode has been programmed to
start at 20:30. At 19:30 a blackout occurs. When the power
supply is restored, the mode will have to be reprogrammed).
! There is no preheating stage for the GRILL mode.
! Never put objects directly on the bottom of the oven; this
will prevent the enamel coating from being damaged.
! Always place cookware on the rack(s) provided.
! The oven will begin its preheating phase after 2 seconds
from selecting the desired cycle.
Cooling ventilation
In order to cool down the external temperature of the oven, a
cooling fan blows a stream of air between the control panel
and the oven door, as well as towards the bottom of the
oven door.In the FAST COOKING mode, the fan is activated
automatically after ten minutes. At the beginning of the
FAST CLEAN mode, the cooling fan operates at low speed.
! Once cooking has been completed, the cooling fan continues
to operate until the oven has cooled down sufficiently.
buzzer will sound. The first time the
button is pressed, the
oven will behave as if it is being switched on for the first time.
Standby
This product complies with the requirements of the latest
European Directive on the limitation of power consumption
of the standby mode. If no buttons are pressed for 30
minutes and the control panel/door lock has not been
activated, the appliance automatically reverts to standby
mode. The standby mode is visualised by the high luminosity
“Watch Icon”. As soon as interaction with the machine
resumes, the system’s operating mode is restored.
Modes
! In order to guarantee wonderfully soft and crunchy
foodstuffs, the oven releases – in the form of water vapour the humidity naturally withheld in the food itself. In this way,
optimal cooking results can be achieved for all types of food.
! Every time the oven is switched on, it suggests the first
manual cooking mode.
Manual cooking modes
! All cooking modes have a default cooking temperature
which may be adjusted manually to a value between 30°C
and 250°C as desired.In the GRILL mode, the default power
level value is indicated as a percentage (%) and may also
be adjusted manually. Any temperature adjustments will be
stored in the appliance memory and suggested again the
next time this mode is used. If the selected temperature is
higher than the temperature inside the oven, the text “Hot”
appears on the display. However, it will still be possible to
start cooking.
Oven light
The light comes on when the oven door is opened or when
a cooking mode starts.
When models featuring LED INSIDE technology begin
cooking, the LEDs on the door light up for improved
illumination of all cooking levels.
MULTILEVEL mode
All heating elements and the fan are activated. Since the
heat remains constant throughout the oven, the air cooks
and browns food in a uniform manner. A maximum of two
racks may be used at the same time.
button can be used to switch on the light at any time.
GRILL mode
The top heating element and the rotisserie spit (where
present) are activated. The high and direct temperature
of the grill is recommended for food which requires a high
surface temperature. Always cook in this mode with the oven
door closed (see “Practical cooking advice”).
The
Residual heat indicators
The appliance is fitted with a residual heat indicator. When
the oven is off, the “residual heat” bar on the display lights
up to indicate high temperatures inside the oven cavity. The
individual segments of the bar switch off one by one as the
temperature inside the oven falls.
Restoring the factory settings
The oven factory settings can be restored to reset all
selections made by the user (clock and customised
durations). To carry out a reset, switch off the oven, then
press and hold the button corresponding to the first manual
button simultaneously
cooking mode (top left) and the
for 6 seconds. Once the restore procedure is complete, a
8
FAN GRILLING mode
The top heating element and the rotisserie spit (where
present) are activated and the fan begins to operate.
During part of the cycle the circular heating element is
also activated. This combination of features increases the
effectiveness of the unidirectional thermal radiation provided
by the heating elements through the forced circulation of
the air throughout the oven.
This helps prevent food from burning on the surface and
allows the heat to penetrate right into the food. Always
cook in this mode with the oven door closed (see “Practical
cooking advice”).
FAST COOKING mode
This mode is particularly suitable for cooking pre-packed
food quickly (frozen or pre-cooked). The best results are
achieved using one cooking rack only.
LOW TEMPERATURE modes
This type of cooking can be used for proving, defrosting,
preparing yoghurt, heating dishes at the required speed and
slow cooking at low temperatures. The temperature options
are: 40, 65 and 90°C.
BAKING mode
The rear heating element and the fan are switched on, thus
guaranteeing the distribution of heat in a delicate and uniform
manner throughout the entire oven. This mode is ideal for baking
temperature sensitive foods (such as cakes, which need to rise).
PIZZA modes
The top and circular heating elements switch on and the fan
begins to operate. This combination heats the oven rapidly.
If you use more than one rack at a time, switch the position
of the dishes halfway through the cooking process.
ECO mode
The rear heating element and the fan are switched on,
thus guaranteeing the distribution of heat in a delicate and
uniform manner throughout the entire oven.This energy
saving mode is recommended for small dishes, ideal for
heating foods and finishing off cooking.
Rotisserie spit*
To operate the rotisserie
function (see diagram)
proceed as follows:
1. Place the dripping pan in
position 1.
2. Place the rotisserie
support in position 3 and
insert the spit in the hole
provided on the back panel
of the oven.
3. Start the rotisserie
function by selecting the
or
modes;
! When
mode is on, the rotisserie will stop if the door
is opened.
Automatic cooking modes
! The temperature and cooking duration are pre-set values,
guaranteeing a perfect result every time - automatically. These
values are set using the C.O.P.® (Programmed Optimal
Cooking) system. The cooking cycle stops automatically and
the oven indicates when the dish is cooked. You may start
cooking whether the oven has been preheated or not.
The cooking duration can be customised according to
personal taste by modifying the relevant value - before
cooking begins - by ±5/20 minutes depending on the
selected programme. The duration can however be modified
even once cooking has begun. If the value is modified
before the programme begins, it is stored in the memory
and suggested again by the appliance when the programme
is next used. If the temperature inside the oven is higher
than the suggested value for the selected mode, the text
“Hot” appears on the TEMPERATURE display and it will
not be possible to begin cooking; wait for the oven to cool.
! When the cooking stage has been reached, the oven
buzzer sounds.
! Do not open the oven door as this will disrupt the cooking
time and temperature.
BAKED CAKES mode
This function is ideal for cooking desserts which are made
using natural yeast, baking powder and desserts which
contain no yeast. Place the dish in the oven while it is still
cold. The dish may also be placed in a preheated oven.
BREAD mode
Use this function to bake bread. To obtain the best results, we
recommend that you carefully observe the instructions below:
• follow the recipe;
• do not exceed the maximum weight of the dripping pan;
• remember to pour 50 g (0,5 dl) of cold water into the
baking tray in position 5.
• The dough must be left to rise at room temperature for
1 – 1 ½ hours (depending on the room temperature) or
until the dough has doubled in size.
Recipe for BREAD:
1 Dripping pan holding 1000 g Max, lower level
2 Dripping pans each holding 1000 g Max, medium and
lower levels
Recipe for 1000 g of dough: 600 g flour, 360 g water, 11g
salt, 25 g fresh yeast (or 2 sachets of powder yeast)
Method:
• Mix the flour and salt in a large bowl.
• Dilute the yeast in lukewarm water (approximately 35
degrees).
• Make a small well in the mound of flour.
• Pour in the water and yeast mixture.
• Knead the dough by stretching and folding it over itself
with the palm of your hand for 10 minutes until it has a
uniform consistency and is not too sticky.
• Form the dough into a ball shape, place it in a large bowl
and cover it with transparent plastic wrap to prevent the
surface of the dough from drying out. Select the manual
LOW TEMPERATURE function on the oven and set the
temperature to 40°C. Place the bowl inside and leave
the dough to rise for approximately 1 hour (the dough
should double in volume).
• Cut the dough into equal sized loaves.
• Place them in the dripping pan, on a sheet of baking
paper.
* Only available in certain models.
9
AUS
AUS
• Dust the loaves with flour.
• Make incisions on the loaves.
• Place the food inside the oven while it is still cold.
• Start the
BREAD cooking mode.
• Once baked, leave the loaves on one of the grill racks
until they have cooled completely.
Programming cooking
! A cooking mode must be selected before programming
can take place.
button until the
icon and the numerical
1. Press the
digits on the display begin to flash.
2. Turn the TIMER knob towards “ ” and “ ” to adjust the
time as desired; keep the knob in position to scroll through
the numbers more quickly and make the setting process
easier.
3. Once you have reached the desired duration, press the
button again. The display will show the duration and
set temperature alternately.
button to begin cooking.
4. Press the
5. When cooking has finished, “END” appears on the display
and a buzzer sounds.
• For example: it is 9:00 a.m. and a duration of 1 hour and
15 minutes is programmed. The programme will stop
automatically at 10:15 a.m.
Setting the end time for a cooking mode
! A cooking duration must be set before the cooking end
time can be scheduled.
! For the delayed programming to work properly, the clock
should be set to the correct time.
1. Follow steps 1 to 3 to set the duration as detailed above.
2. Press the
button twice: the
icon and the
numerical digits on the display will begin to flash.
3. Turn the TIMER knob towards “ ” and “ ” to adjust the
cooking end time value.
4. Once you have reached the desired end time, press the
button again. The display will show the duration, the
cooking end time and the set temperature alternately.
button to activate the programmed mode.
Programming has been set when the
and
buttons
are illuminated. The DISPLAY shows the cooking end time
and the cooking duration alternately.
6. Once cooking has finished, “END” appears on the display
and a buzzer sounds.
• For example: it is 9:00 a.m. and a time of 1 hour and
15 minutes is programmed, while the end time is set to
12:30. The programme will start automatically at 11:15
a.m.
To cancel programming press the
10
! Do not place racks in position 1 and 5 during fan-assisted
cooking. This is because excessive direct heat can burn
temperature sensitive foods.
! In the GRILL and FAN GRILLING cooking modes,
particularly when using the rotisserie spit, place the dripping
pan in position 1 to collect cooking residues (fat and/or
grease).
MULTILEVEL
Programming the cooking duration
5. Press the
Practical cooking advice
button.
• Use positions 2 and 4, placing the food which requires
more heat on 2.
• Place the dripping pan on the bottom and the rack on
top.
GRILL
• Place the rack in position 3 or 4. Position the food in the
centre of the rack.
• We recommend that the temperature is set to its
maximum level. The top heating element is regulated by
a thermostat and may not always operate constantly.
PIZZA
• Use a lightweight aluminium pizza pan. Place it on the
rack provided.
For a crispy crust, do not use the dripping pan as this
extends the total cooking duration and prevents the crust
from forming.
• If the pizza has a lot of toppings, we recommend adding
the mozzarella cheese to the top of the pizza halfway
through the cooking process.
Cooking advice table
Modes
Foods
Weight
(Kg)
standard
guide rails
Manual
Multilevel*
Pizza on 2 racks
Pies on two racks/cakes on 2 racks
Sponge cake on 2 racks (on the dripping pan)
Roast chicken + potatoes
Lamb
Mackerel
Lasagne
Cream puffs on 3 racks
Biscuits on 3 racks
Cheese puffs on 2 racks
Savoury pies
Rack position
1+1
1
1
1
Preheating
Recommended
Temperature
(°C)
Cooking
duration
(minutes)
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
220-230
180
170
200-210
190-200
180
190-200
190
190
210
200
20-25
30-35
20-25
65-75
45-50
30-35
35-40
20-25
10-20
20-25
20-30
sliding
guide rails
2 and 4
1 and 3
2 and 4
1 and 3
2 and 4
1 and 3
1 and 2/3
1 and 3
2
1
1 or 2
1
2
1
1 and 3 and 5 1 and 2 and 4
1 and 3 and 5 1 and 2 and 4
2 and 4
1 and 3
1 and 3
1 and 3
Grill*
Mackerel
Sole and cuttlefish
Squid and prawn kebabs
Cod fillet
Grilled vegetables
Veal steak
Sausages
Hamburgers
Toasted sandwiches (or toast)
Spit-roast chicken using rotisserie spit (where present)
Spit-roast lamb using rotisserie spit (where present)
1
0,7
0,7
0,7
0,5
0,8
0,7
n° 4 or 5
n° 4 or 6
1
1
4
4
4
4
3 or 4
4
4
4
4
-
3
3
3
3
2 or 3
3
3
3
3
-
no
no
no
no
no
no
no
no
no
no
no
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
15-20
10-15
8-10
10-15
15-20
15-20
15-20
10-12
3-5
70-80
70-80
Fan grilling*
Grilled chicken
Cuttlefish
Spit-roast chicken using rotisserie spit (where present)
Spit-roast duck using rotisserie spit (where present)
Roast veal or beef
Roast pork
Lamb
1,5
1
1,5
1,5
1
1
1
2
2
2
2
2
2
2
2
2
2
no
no
no
no
no
no
no
210
200
210
210
210
210
210
55-60
30-35
70-80
60-70
60-75
70-80
40-45
Pizza
Courgette and prawn pie
Country style spinach pie
Turnovers
Lasagne
Golden rolls
Chicken bites
0.3
0.4
0.5
0.3
0.5
0.4
0.4
2
2
2
2
2
2
2
1
1
1
1
1
1
1
-
250
200
220
200
200
180
220
12
20
30-35
25
35
25-30
15-20
Pre-cooked food
Golden chicken wings
0.4
2
1
-
200
20-25
Fresh Food
Biscuits (shortcrust pastry)
Sponge cake made with yoghurt
Cheese puffs
0.3
0.6
0.2
2
2
2
1
1
1
-
200
180
210
15-18
45
10-12
Duck
Chicken
Roast veal or beef
Roast pork
Biscuits (shortcrust pastry)
Tarts
1,5
1,5
1
1
1
2
2
2
2
2
2
1
1
1
1
1
1
yes
yes
yes
yes
yes
yes
200-210
200-210
200
200-210
180
180
70-80
60-70
70-75
70-80
15-20
30-35
Tarts
Fruit cakes
Sponge cake made with yoghurt
Small cakes on 2 racks
Sponge cake
Cream puffs on 3 racks
Biscuits on 3 racks
Filled pancakes
Meringues on 3 racks
Cheese puffs
0,5
1
0,7
0,7
0,6
0,7
0,7
0,8
0,5
0,5
2 or 3
2 or 3
2 or 3
2 and 4
2 or 3
1, 3 and 5
1, 3 and 5
2
1, 3 and 5
2
1 or 2
1 or 2
1 or 2
1 and 3
1 or 2
1, 2 and 4
1, 2 and 4
1
1, 2 and 4
1
180
180
170-180
180-190
160-170
180-190
180
200
90
210
25-35
40-50
45-55
20-25
30-40
20-25
20-25
30-35
180
20-25
Fish fillets
Lamb skewers
Hamburgers
0,5
0,7
0,6
0,7
0,5
0,5
0,5
0,5
0,5
2 or 3
2 and 4
2 or 3
1 and 3
2
1 and 3
2o3
2o3
2o3
1 or 2
1 and 3
1 or 2
1 and 2
1
1 and 2
1o2
1o2
1o2
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
200
200
180
200
200
90
200
200
200
30-40
20-25
35-40
20-25
20-30
180
20-25
20-25
20-25
Pizza
Focaccia bread
0,5
0,5
2
2
1
1
yes
yes
220
200
15-20
20-25
Baked cakes
1
2 or 3
2
no
Bread (see recipe)
1
1 or 2
1
no
Fast cooking* Frozen food
Low
temperature*
Baking*
ECO*
Pizza*
Automatic**
Baked cakes
Bread***
* The cooking times listed above are intended as guidelines only and may be modified according to personal tastes. Oven preheating times are set as
standard and may not be modified manually.
** The duration of the automatic cooking functions are set by default. The values can be modified by the user, starting with the default duration.
*** As stated in the recipe, pour 100 g (1 dl) water into the dripping pan in position 5.
11
AUS
AUS
Precautions and tips
! This appliance has been designed and manufactured
in compliance with international safety standards. The
following warnings are provided for safety reasons and
must be read carefully.
General safety
• The appliance was designed for domestic use inside the
home and is not intended for commercial or industrial use.
• The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
• When moving or positioning the appliance, always use
the handles provided on the sides of the oven.
• Do not touch the appliance while barefoot or with wet or
damp hands and feet.
• The appliance must be used by adults only for
the preparation of food, in accordance with the
instructions provided in this booklet. Any other
use of the appliance (e.g. for heating the room)
constitutes improper use and is dangerous. The
manufacturer may not be held responsible for any
damage caused as a result of improper, incorrect
and unreasonable use of the appliance.
• Do not touch the heating elements or certain parts
of the oven door when the appliance is in use; these
parts become extremely hot. Keep children well away
from the appliance.
• Make sure that the power supply cables of other electrical
appliances do not come into contact with the hot parts of
the oven.
• The ventilation and heat dispersal openings must never
be obstructed.
• Always grip the oven door handle in the centre: the ends
may be hot.
• Always use oven gloves when placing cookware in the
oven or when removing it.
• Do not use aluminium foil to line the bottom of the oven.
• Do not place flammable materials in the oven: if the
appliance is switched on accidentally, the materials could
catch fire.
• When unplugging the appliance, always pull the plug
from the mains socket; do not pull on the cable.
• Do not perform any cleaning or maintenance work without
having disconnected the appliance from the electricity
mains.
• If the event of malfunctions, under no circumstances
should you attempt to perform the repairs yourself.
Contact an authorised Service Centre (see Assistance).
• Do not rest objects on the open oven door.
• Do not let children play with the appliance.
• The appliance should not be operated by people (including
children) with reduced physical, sensory or mental
capacities, by inexperienced individuals or by anyone
who is not familiar with the product. These individuals
should, at the very least, be supervised by someone who
assumes responsibility for their safety or receive preliminary
instructions relating to the operation of the appliance.
• The appliance is not intended to be operated by
means of an external timer or separate remotecontrol system.
12
Disposal
• When disposing of packaging material: observe local
legislation so that the packaging may be reused.
• The European Directive 2012/19/EC on Waste
Electrical and Electronic Equipment (WEEE), requires
that old household electrical appliances must not
be disposed of in the normal unsorted municipal
waste stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product
reminds you of your obligation, that when you dispose
of the appliance it must be separately collected.
Consumers should contact their local authority or retailer
for information concerning the correct disposal of their
old appliance.
Respecting and conserving the environment
• You can help to reduce the peak load of the electricity
supply network companies by using the oven in the
hours between late afternoon and the early hours of
the morning. The cooking mode programming options,
the “delayed cooking” mode (see Cooking modes) and
“delayed automatic cleaning” mode (see Care and
Maintenance) in particular, enable the user to organise
their time efficiently.
• Always keep the oven door closed when using the GRILL
and FAN GRILLING modes: this will achieve improved
results while saving energy (approximately 10%).
• Check the door seals regularly and wipe them clean
to ensure they are free of debris so that they adhere
properly to the door, thus avoiding the dispersal of heat.
! This product complies with the requirements of the latest
European Directive on the limitation of power consumption
of the standby mode.
Maintenance and care
Switching the appliance off
Disconnect your appliance from the electricity supply before
carrying out any work on it.
Cleaning the appliance
• Slight differences in colour on the front of the oven are due
to the different materials used, i.e. glass, plastic or metal.
• Any shady areas resembling grooves on the oven door
glass are caused by reflections from the oven light.
• The enamel is branded at very high temperatures. This
process may cause colour variations. This is normal and
will not affect appliance operation in any way. The thin
edges of the sheet metal cannot be entirely enamelled
and may therefore appear to be unfinished. This will not
affect the rust protection.
• The stainless steel or enamel-coated external parts and
the rubber seals may be cleaned using a sponge that
has been soaked in lukewarm water and neutral soap.
Use specialised products for the removal of stubborn
stains. After cleaning, rinse and dry thoroughly. Do not
use abrasive powders or corrosive substances.
• The inside of the oven should ideally be cleaned after
each use, while it is still lukewarm. Use hot water and
detergent, then rinse well and dry with a soft cloth. Do
not use abrasive products.
• All accessories - with the exception of the sliding racks
- can be washed like everyday crockery, and are even
dishwasher safe.
• We recommend that detergents are not sprayed directly
onto the control panel, but that a sponge is used instead.
! Do not touch the light bulb directly with your hands.
AUS
! Do not use the oven lamp as/for ambient lighting.
Sliding rack kit assembly
! Never use steam cleaners or pressure cleaners on the
appliance.
A
To assemble the sliding
racks:
1. Remove the two frames,
lifting them away from the
spacers A (see figure).
Cleaning the oven door
! The door of LED INSIDE models cannot be removed.
Clean the glass part of the oven door using a sponge and
a non-abrasive cleaning product, then dry thoroughly with
a soft cloth. Do not use rough abrasive material or sharp
metal scrapers as these could scratch the surface and cause
the glass to crack.
For more thorough cleaning purposes, the oven door may
be removed:
1. Open the oven door fully (see diagram).
2. Use a screwdriver to lift up and turn the small levers F
located on the two hinges (see diagram).
Left
guide rail
Right guide
rail
B
C o Dire
f e ct
xt ion
ra
ct
io
n
F
3. Grip the door on the two outer
sides and close it approximately
half way. Pull the door towards you,
lifting it out of its slot (see diagram).
To replace the door, reverse this
sequence.
D
2. Choose which shelf to use
with the sliding rack. Paying
attention to the direction in
which the sliding rack is to
be extracted, position joint B
and then joint C on the
frame.
3. Secure the two frames
with the guide rails using the
holes provided on the oven
walls (see diagram). The
holes for the left frame are
situated at the top, while the
holes for the right frame are
at the bottom.
4. Finally, fit the frames on
the spacers A.
! Do not place the sliding racks in position 5.
Automatic cleaning with the FAST CLEAN
function
Inspecting the seals
Check the door seals around the oven regularly. If the seals
are damaged, please contact your nearest Service Centre
(see Assistance). We recommend that the oven is not used
until the seals have been replaced.
Replacing the light bulb
Lamp
Holder
compartment
Lamp
Glass cover
To replace the oven light
bulb:
1. Remove the glass cover
of the lamp-holder.
2. Remove the light bulb and
replace it with a similar one:
halogen lamp voltage 230 V,
wattage 25 W, cap G 9.
3. Replace the glass cover
(see diagram).
With the FAST CLEAN mode, the internal temperature of the
oven reaches 500°C. The pyrolytic cycle is activated, burning
away food and grime residues. Dirt is literally incinerated.
Keep children away from the appliance during the automatic
cleaning cycle as surfaces may become very hot. Particles
may ignite inside the oven as a result of the combustion
process. There is no cause for concern: this process is both
normal and hazard-free.
Before initiating the FAST CLEAN mode:
• clean the oven door;
• remove large or coarse food residues from the inside of
the oven using a damp sponge. Do not use detergents;
• remove all accessories and the sliding rack kit (where
present);
• do not place tea towels or pot holders over the oven
handle.
13
AUS
! If the oven is too hot, the pyrolytic cycle may not start.
Wait for the oven to cool down.
Programming the automatic cleaning end time
! The programme may only be started once the oven door
has been closed.
1. Press the
button twice: the
icon and the
numerical digits on the display will begin to flash.
2. Turn the TIMER knob towards “ ” and “ ” to adjust the
cleaning end time value.
3. Once you have reached the desired end time, press the
! The desired Fast Clean mode will be confirmed and started
automatically if the CLOCK icon button is not pressed within
10 seconds from selecting the cooking time.
To activate the Fast Clean programme:
1. Switch the control panel on by pressing the
4. Press the
button.
2. Press button
; the display will show the text “Piro”,
“nor” and the default duration of 1:30 h (normal cycle)
alternately.
3. Press button
, then turn the TIMER knob to adjust the
default cleaning level. There are 3 different levels to choose
from, each with a pre-set duration which cannot be modified:
1. Economy (ECO): turn the knob towards “ ”. Duration
1 hour.
2. Normal (NOR): initial level. Duration 1 hour and 30
minutes.
3. Intensive (INT): turn the knob towards “ ”. Duration 2
hours.
4. Press the
button to confirm.
5. Press the
button to begin the cleaning cycle.
An end time for the FAST CLEAN cycle (as for a normal
cooking cycle) may be programmed (see Programming the
automatic cleaning end time).
Safety devices
• the door locks automatically as soon as the temperature
reaches a high value; the
display;
icon lights up on the
• pressing the
button cancels the cleaning cycle at
any time;
• if a malfunction occurs, the heating elements will be
switched off;
• once the oven door has been locked, you cannot change
the duration and end time settings.
14
button again. The display will show the duration, the
cleaning end time and the set cleaning level alternately.
button to activate the programmed mode.
Programming has been set when the
and
buttons
are illuminated.
5. Once cleaning has finished, “END” appears on the display
and a buzzer sounds.
• For example: it is 9:00 a.m. and the Economy (ECO)
FAST CLEAN level has been selected, with the default
duration of 1 hour. 12:30 is scheduled as the end time.
The programme will start automatically at 11:30 a.m.
To cancel programming press the
button.
Once the automatic cleaning cycle is over
Before you can open the oven door, you will have to wait
for the
icon to switch off: this indicates the oven
temperature has dropped to an acceptable level. You will
notice some white dust deposits on the bottom and the sides
of your oven; remove these deposits with a damp sponge
once the oven has cooled down completely. Alternatively,
you can make use of the already heated oven, in which
case it is not necessary to remove the deposits, they are
completely harmless and will not affect your food in any way.
Troubleshooting
AUS
Problem
Possible cause
The “Clock button” and the
digits on the display flash.
Set the clock.
The appliance has just been
connected to the electricity mains
or there has been a blackout.
There has been a blackout.
Reprogram the cooking mode.
A programmed cooking mode
does not start.
Only the high luminosity
“Clock button” is lit.
An automatic mode has been
selected. “Hot” appears on the
display and cooking does not
start.
Fan-assisted cooking has been
selected and the food looks burnt.
Solution
The appliance is in standby mode Press any button to exit
standby mode.
The temperature inside the oven Wait for the oven to cool down.
is higher than the suggested
value for the selected mode.
Positions 1 and 5: the direct
heat could cause
temperature-sensitive
foods to burn.
We recommend switching
dripping pan positions halfway
through cooking.
15
195102562.01
04/2013 - XEROX FABRIANO
AUS
16