country flame urban lifestyle
Cannon Gas Log Heaters
Specifications
Share a lifetime of cosy moments with
Cannon Gas Log Heaters.
2
Please refer to Cannon website for up to date specifications.
Cannon index
Hot chocolate with marshmallows, cuddles and chats are just a few of the cosy moments
that you can enjoy in front of a Cannon Gas Log Heater. Providing you with rapid warmth
and the romance of a real log fire without the mess, a Cannon Gas Log Heater is simple
to operate and energy efficient. Start your lifetime of cosy moments this Winter.
How to Build a Mock Fireplace
Page 4
Details
Powerflue
Page 5
Installation options
Fitzroy Inbuilt and Powerflue
Heater features and options guide
Page 6
Canterbury Inbuilt and Freestanding
Heater features and options guide
Page 7
Weather Proof Box
Page 7
Dimensions
Fitzroy Inbuilt, Freestanding and Powerflue
Specifications and installations notes
Page 8
Canterbury Inbuilt and Freestanding
Specifications and installations notes
Page 9
Fitzroy Inbuilt, Freestanding and Powerflue
Page 10
Dimensions
Canterbury Inbuilt and Freestanding
Dimensions
Page 11
Surround and Spacer Kit
Dimensions
Page 11
Please refer to Cannon website for up to date specifications.
3
How to Build a Mock Fireplace
1+2+3+4
Creating the look of a fireplace is simple
Whether flueing up in the wall cavity or
Note: The purpose of the diagrams shown here are to
with Cannon.
through ceiling plaster, simply construct
briefly illustrate the steps to install a heater in a mock
a purpose built timber or plasterboard
If you don’t have a fireplace but like the
enclosure to conceal the heater cabinet
look, our mock fireplace kit is the answer.
fireplace. For full details refer to the comprehensive
instructions included with the heater or visit www.
cannonheaters.com.au
and flue.
Using the kit, your inbuilt heater can be
easily and safely installed in a plasterboard
You must use a mock fireplace kit with an
or timber wall.
inbuilt heater for installation into combustible
areas i.e. timber, plasterboard etc. (Mock
Fireplace kit included with Powerflue model)
1
Choose your location and
build a frame to enclose
the heater according to
your flueing needs. Allow
for required clearances
between the heater
cabinet and combustible
surfaces. See below
table and refer to mock
installation instructions
or website for further
detailed measurement
requirements
2
3
Installation of appropriate
self-supported flue
which complies with
local regulations and
manufacturer instructions.
Refer to mock installation
instructions or website for
details on mounting of wall
brackets & flue transition
(brackets are supplied with
mock kit only).
4
Use plasterboard or
timber panelling to
enclose the frame,
maintaining appropriate
clearances. Plasterboard
opening should be cut
back level with timber
framework.
Attach the mock fireplace
kit to the heater per the
instructions. Position
the heater in the frame.
Refer to mock installation
instructions or website
for further details on
installing mock kit
components on heater.
Mock Fireplace Opening (combustible materials)^
FITZROY INBUILT
FITZROY POWERFLUE
CANTERBURY INBUILT
Max
Min
Max
Min
Max
Min
Height
640 mm
630 mm
650 mm
630 mm
640 mm
630 mm
Width
780 mm
731 mm
780 mm
731 mm
790 mm
731 mm
N/A
410 mm*
N/A
486mm - 586mm** N/A
Depth
^
363 mm*
If you have a larger opening than the maximum height indicated, a surround kit is recommended. *Includes 25 mm clearance between flue spigot and rear wall.
**486mm min clearance for straight through flue. 586mm min clearance for vertical flexi flue pipe.
4
Please refer to Cannon website for up to date specifications.
Powerflue installation options
Cannon’s Powerflue has some unique installation and operation advantages.
Unlike standard gas log heaters, the
Because the Powerflue model draws air
Powerflue can be terminated horizontally
from outside for combustion and then vents
from the rear of the unit, eliminating the
outside via the flue outlet, it is safe to install
need for the flue to run up through the
into a bedroom or 5 star energy rated home
wall and protrude above the roof line.
that is well sealed from draughts.
This means you can place the heater on
any external wall, even in a multi-storey
A Cannon Powerflue heater must also be
installed with a condensate drainage tube
apartment.
as seen in the drawings below.
The Cannon Fitzroy Powerflue can also
be flued up through an internal wall or out
under the floor making it truly versatile.
Standard heater operation.
Powerflue operation.
Flue goes directly
Air is drawn in from
through the ceiling
outside for combustion
and roof.
via the air inlet and vented
outside via the flue outlet.
1
Horizontal installation
from the back.
2
Vertical installation.
3
Under floor installation.
4
Sideways horizontal
installation.
Please refer to Cannon website for up to date specifications.
5
Fitzroy Inbuilt and Powerflue heater features and options guide
Fitzroy Inbuilt Models
Fitzroy Powerflue Models
FITZIB- FITZIB- FITZIB- FITZIB- FITZIB- FITZIB- FITZIBSMENB- SMENB- SMEXB- SMEXB- SMEXP- SMEXP- PMEXBNG
LP
NG
LP
NG
LP
NG
FITZIBPMEXBLP
FITZIBPMEXPNG
FITZIBPMEXPLP
Standard
Features
Electronic ignition
•
•
•
•
•
•
•
•
•
•
3 heat settings
•
•
•
•
•
•
•
•
•
•
3 speed fan
•
•
•
•
•
•
•
•
•
•
Realistic eucalypt
look logs
•
•
•
•
•
•
•
•
•
•
Standard flue
•
•
•
•
•
•
•
•
•
•
Power flue
Mesh guard
•
•
•
•
•
•
•
•
•
•
Panoramic view
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Enhanced flame
Black enamel finish
•
•
Platinum finish
•
•
Options
Remote thermostat
o
o
o
o
o
o
o
o
o
o
Glass kit
o
o
o
o
o
o
o
o
o
o
Spacer kit
o
o
o
o
o
o
o
o
o
o
Surround kit
o
o
o
o
o
o
o
o
o
o
Console kit
o
o
o
o
o
o
o
o
o
o
o
o
o
o
•
•
•
•
o
o
o
o
Weatherproof box
Mock fireplace kit
o
o
o
o
Freestanding kit (incl.
flue kit)
o
o
o
o
o
o
Extended flue kit
Inbuilt flue kit
o
o
o
o
• These items are supplied as standard with the heater
o These items are not supplied with the heater and must be purchased separately
Please note: All Cannon inbuilt heaters
MUST be flued. We recommend our own
Inbuilt flue kit be used which is purchased
separately (model IBFLUEKIT).
The Powerflue heaters are supplied with
the flue and cowl to be vented directly out
the back through an external wall. If you
wish to flue this unit vertically out through
the roof or down under the floor the
Extended Flue Kit will need to be purchased
(model FLUEWFX).
6
Please refer to Cannon website for up to date specifications.
o
o
Canterbury Inbuilt and Freestanding heater features and options guide
Canterbury Inbuilt Models
Canterbury Freestanding Models
CANTIBSDEEBNG
CANTIBSDEEBLP
CANTFSSDEEBNG
CANTFSSDEEBLP
Electronic ignition
•
•
•
•
3 heat settings
•
•
•
•
3 speed fan
•
•
•
•
Realistic eucalypt look
logs
•
•
•
•
Standard flue
•
•
•
•
Enhanced flame
•
•
•
•
Black enamel finish
•
•
•
•
Remote thermostat
o
o
o
o
Spacer kit
o
o
Surround kit
o
o
Console kit
o
o
Mesh guard kit
o
o
o
o
Mock fireplace kit
o
o
o
o
Standard Features
Options
Freestanding Flue kit
o
Inbuilt Flue kit
o
Please note: When purchasing a Canterbury Freestanding Heater you will also need to purchase the appropriate flue kit (model FLUERO-B).
When selecting the type of heater, consideration must be given as to the construction of the building with regards to the energy efficiency. This will effect the efficiency of the type
of flue selected and how it will operate – e.g. High Energy Efficient rated homes have no allowance for the introduction of fresh air for combustion purposes, therefore issues can
arise with reverse flow of air through a standard flue in these homes. Two storey extensions to existing homes can also create reverse air flow through standard flues.
Avoid installing standard flue heaters on external perimeter walls of high pitched roof buildings to reduce the possibility of reversed air flow through the standard flue. If in doubt
always select the Powerflue as it is not affected by these issues.
Weather Proof Box dimensions
The weatherproof box is designed to be used on the
Fitzroy Powerflue heaters that are installed on an external
wall and protects the back of the heater from the elements.
792 mm
848 mm
720 mm
660 mm
351 mm
524mm with cap removed
573mm with cap fitted
Weatherproof box
Please refer to Cannon website for up to date specifications.
7
Fitzroy Inbuilt, Freestanding and Powerflue specifications and installations notes
Fitzroy Inbuilt
Fitzroy Freestanding
FITZIB-SMENB / FITZIB-SMEXB / FITZIB-SMENB or FITZIB-SMEXB
FITZIB-SMEXP
to be used with FITZFSKITX-B
FITZIB-PMEXB or FITZIB-PMEXP
Type
Inbuilt
Freestanding / top flue
Inbuilt Powerflue with variable
flue options
Colours
Metallic black baked enamel or
platinum finish
Metallic black baked enamel finish
Metallic black baked enamel or
platinum finish
Gas consumption
26 MJ/hr
26 MJ/hr
26 MJ/hr
Gas type
Natural gas/LPG
Natural gas/LPG
Natural gas/LPG
Efficiency rating
4.06 stars
4.06 stars
5.05 stars1 for units with flue 400 mm
long 5.50 stars1 for units with flue 6.0
m long
Heat output
5.98 kW / 21.45 MJ/h
Heats on average
80 square metres (80 m )
80 square metres (80 m )
80 square metres (80 m2)
Fan/heat settings
3 speed / 3 heat
3 speed / 3 heat
3 speed / 3 heat
Dimensions
Fascia
Overall
Fascia
Height
651 mm
863 mm
651 mm
Width
808 mm
808 mm
808 mm
Depth
50 mm
482 mm
Min. distance from centre of flue to
wall at rear of heater: 120 mm
50 mm
Installation
Fireplace opening
(brick & masonry)
Kit comprising:
3 x 870 mm lengths of 125 mm dia.
painted flue,
1 x 870 mm length of 125 mm dia.
plain flue,
1 x ceiling ring,
1 x painted bottom flue spigot,
1 x 125 mm cowl,
1 x 75 mm spigot plain
Fasteners
Free standing casing
1 x flue adaptor
Fireplace opening (brick &
masonry)
The purpose of
these pages is to
briefly illustrate the
specifications. For
full details refer to
the comprehensive
instructions included
with the heater or visit
www.cannonheaters.
com.au. Whilst
every effort is made
to provide current
information at the
time this brochure
was produced,
continuing product
development means
that the enclosed
specifications, images
and literature may
differ.
1
1
5.98 kW / 21.45 MJ/h
2
Max
Min
Height
645 mm
605 mm
Width
780 mm
700 mm
Depth
N/A
410 mm*
* Includes 25 mm clearance between
flue spigot and rear brickwork
Maximum length of flue: 4.5m
Mock openings differ to brick/
masonry see page 4 for mock
opening dimensions.
Suitable for non-combustible or
masonry/brick fireplaces or
into a mock fireplace using a Mock
Kit purchased separately.
Gas connection
via a ½” copper
compression fitting.
A 10 amp socket
within 1.5 m is
required. Inbuilt
models can be
direct wired with an
accessible isolating
switch
Tested to AS
4553:2008.
1
8
Fitzroy Powerflue
Please refer to Cannon website for up to date specifications.
6.09kW / 21.92 MJ/h
2
Maximum length of flue: 4.5m (extra
length of flue required)
Heater does not require noncombustible base.
Can be installed against a
combustible wall with clearances of
40 mm rear, 100 mm side and 900
mm in front of heater.
Refer to installation instructions.
Max
Min
Height
645 mm
605 mm
Width
780 mm
700 mm
Depth
N/A
see page 10
Dimensions of flue
Flue and air inlet through 50 mm
diameter aluminium & PVC pipes
2 x 400 mm lengths of 50 mm
flexible aluminium hose
Dimensions of flue terminal
Maximum length of flue: 6.0 m
Minimum length of flue: 130 mm
Flue terminal: 160 mm outer
diameter.
150 mm deep
(horizontal)
200 mm high (vertical)
See installation instructions for further details.
Mock Kit included with heater, may
need to be removed from brick/
masonry openings to allow fitment in
openings less than 630 mm high.
Canterbury Inbuilt and Freestanding specifications and installations notes
Canterbury Inbuilt
Canterbury Freestanding
CANTIB-SDEEB
CANTFS-SDEEB
Type
Inbuilt
Freestanding / top flue
Colours
Metallic black baked enamel finish
Metallic black baked enamel finish
Gas consumption
26 MJ/hr
26 MJ/hr
Gas type
Natural gas/LPG
Natural gas/LPG
Efficiency rating
4.06 stars
4.06 stars1
Heat output
5.98 kW / 21.45 MJ/h
Heats on average
80 square metres (80 m )
80 square metres (80 m2)
Fan/heat settings
3 speed / 3 heat
3 speed / 3 heat
Dimensions
Fascia
Overall
Height
655 mm
723 mm
Width
850 mm
650 mm
Depth
125 mm
425 mm
Min. distance from flue centre to wall
at rear of heater: Round – 115 mm.
Installation
Fireplace opening (brick & masonry)
Flue kit comprising (purchase separately):
3 x 870 mm lengths of 125 mm dia. painted flue,
1 x 870 mm length of 125 mm dia. plain flue,
1 x ceiling ring,
1 x 125 mm cowl,
1 x painted bottom flue spigot.
The purpose of
these pages is to
briefly illustrate the
specifications. For
full details refer to
the comprehensive
instructions included
with the heater or visit
www.cannonheaters.
com.au. Whilst
every effort is made
to provide current
information at the
time this brochure
was produced,
continuing product
development means
that the enclosed
specifications, images
and literature may
differ.
1
5.98 kW / 21.45 MJ/h
2
Max
Min
Height
650 mm
605 mm
Width
780 mm
700 mm
Depth
N/A
363 mm*
* Includes 25 mm clearance between flue spigot and
rear brickwork.
Maximum length of flue: 4.5m
Mock openings differ to brick/masonry, see page 4 for
mock opening dimensions.
Maximum length of flue: 4.5m
Heater does not require non-combustible base. Can be
installed against a combustible wall with clearances of 40
mm rear, 100 mm side and 900 mm in front of heater. This
model is to be installed with a Round Flue Kit part No.
FLUERO-B purchased separately.
Suitable for non-combustible fireplaces ie. masonry, brick
or into a mock fireplace using a Mock kit purchased
separately.
Gas connection
via a ½” copper
compression fitting.
A 10 amp socket
within 1.5 m is
required. Inbuilt
models can be
direct wired with an
accessible isolating
switch
Tested to AS
4553:2008.
1
Please refer to Cannon website for up to date specifications.
9
Fitzroy Inbuilt, Freestanding and Powerflue dimensions
Fitzroy Inbuilt
Fitzroy Freestanding
FITZIB-SMENB, FITZIB-SMEXB or FITZIB-SMEXP
FITZIB-SMENB or FITZIB-SMEXB
to be used with FITZFSKITX-B
Ceiling
1000 mm min clearance
Mantle 300 mm min clearance
385 mm
228 mm
100 mm
900 mm min
clearance
Rear wall of fireplace
40 mm min
back clearance
25 mm min
522 mm
900 mm min clearance
700 - 780 mm
690 mm
FOR INSTALLATIONS
IN NON COMBUSTIBLE
ENCLOSURES:
(Refer to installation
instructions for further
details).
385 mm
600 mm
627 mm
651 mm
Ceiling
1000 mm min clearance
Mantle 300 mm min clearance
For min clearance
see Note 1
Fitzroy Powerflue
FITZIB-PMEXB or FITZIB-PMEXP
1000 mm min clearance
Mantle 300 mm min clearance
For min clearance
see Note 1
Rear wall
of fireplace
For further detailed flueing
methods refer to our website for
the installation instruction manual.
Note 1:
486 mm min clearance for
straight through flue.
586 mm min clearance for
flex flue pipe.
Note 2:
100 mm min clearance for
straight through flue.
200 mm min clearance for
flex flue pipe.
For min clearance
see Note 2
900 mm min
clearance
For further detailed flueing
methods refer to our website for
the installation instruction manual.
Note 1:
486 mm min clearance for
straight through flue.
586 mm min clearance for
flex flue pipe.
Note 2:
100 mm min clearance for
straight through flue.
200 mm min clearance for
flex flue pipe.
For min clearance
see Note 2
900 mm min
clearance
Ceiling
32 mm
41 mm
863 mm
229 mm
450 mm
** Ensure controls are visible
40 mm
50 mm
808 mm
808 mm
100 mm **
690 mm
50 mm
100 mm min
side clearance
700 – 780 mm
FOR INSTALLATIONS
IN NON COMBUSTIBLE
ENCLOSURES:
(Refer to installation
instructions for further
details).
690 mm
808 mm
50 mm 386 mm
50 mm
690 mm
10
Please refer to Cannon website for up to date specifications.
600 mm
700 – 780 mm
651 mm
Rear wall
of fireplace
Canterbury Inbuilt and Freestanding dimensions
Canterbury Inbuilt
Canterbury Freestanding
CANTIB-SDEEB
CANTFS-SDEEB
Ceiling
425 mm
1000 mm min clearance
Mantle 300 mm min clearance
338 mm
180 mm
100 mm
900 mm min
clearance
Rear wall of fireplace
40 mm min
back clearance
25 mm min
522 mm
900 mm min clearance
FOR INSTALLATIONS
IN NON COMBUSTIBLE
ENCLOSURES:
(Refer to installation
instructions for further
details).
700 - 790 mm
690 mm
100 mm min
side clearance
650 mm
600 mm
655 mm
41 mm
** Ensure controls are visible
723 mm
338 mm
180 mm
425 mm
100 mm **
40 mm
125 mm
850 mm
690 mm
630 mm
50 mm
Surround and Spacer Kit dimensions
A
3 sided surround (75 mm)
Height
Fitzroy
Inbuilt
Fitzroy
Powerflue
Canterbury
Inbuilt
725 mm
725 mm
730 mm
Width
960 mm
960 mm
1000 mm
Depth
10 mm
10 mm
10 mm
C
C
B
4 sided surround
Fitzroy
Inbuilt
Spacer kit
Fitzroy
Powerflue
Canterbury
Inbuilt
Fitzroy
Inbuilt
Fitzroy
Powerflue
Canterbury
Inbuilt
Height
850 mm
850 mm
850 mm
Width
1045 mm
1045 mm
1045 mm
Height
651 mm
651 mm
655 mm
Depth
7 mm
7 mm
7 mm
Width
808 mm
808 mm
850 mm
Depth
50 mm
50 mm
50 mm
Frame
Width
A – 95 mm
B – 104 mm
C – 119 mm
A – 95 mm
B – 104 mm
C – 119 mm
A – 91 mm
B – 104 mm
C – 98 mm
Please refer to Cannon website for up to date specifications.
11
Proudly manufactured
and distributed by
Victoria Showroom
Western Australia Showroom
Queensland Showroom
Sampford IXL
421 Smith Street,
Fitzroy, 3065.
Telephone 1300 727 421
Sampford IXL
1/278 Scarborough Beach Road
Osborne Park, 6017.
Telephone 08 9242 5003
Sampford IXL
3/45 Commercial Road
Newstead, 4006.
Telephone 07 3358 3000
Cat. No. BRCANSPECS0212
info@sampfordixl.com.au www.cannonheaters.com.au