dresden elektronik deRFusb-13E06 User manual

User Manual

USB Radio Sticks

deRFusb-23E00 deRFusb-23E06 deRFusb-23E06 JTAG deRFusb-13E00 deRFusb-13E06 deRFusb-13E06 JTAG

Document Version V01.01

2011-07-01

User Manual

Version 01.01

2011-07-01

USB radio sticks deRFusb

Table of contents

1. Overview ......................................................................................................................... 5

2. Application ....................................................................................................................... 5

3. Features .......................................................................................................................... 5

4. Technical data ................................................................................................................. 8

5. Mechanical size ............................................................................................................. 10

6. Pin assignment .............................................................................................................. 11

7. Programming ................................................................................................................. 15

7.1. JTAG interface ..................................................................................................... 15

7.2. USB interface ....................................................................................................... 15

7.3. Required hardware ............................................................................................... 15

7.4. Programming and debugging details .................................................................... 17

8. Onboard transceiver ...................................................................................................... 18

9. Onboard flash (option) ................................................................................................... 18

10. Radio certification .......................................................................................................... 19

10.1. United States (FCC) ............................................................................................. 19

10.2. European Union (ETSI) ........................................................................................ 20

11. Ordering information ...................................................................................................... 22

12. Revision notes ............................................................................................................... 24 dresden elektronik ingenieurtechnik gmbh

Enno-Heidebroek-Str. 12

01237 Dresden / Germany

Tel.: 0351 – 31 85 00

Fax: 0351 – 3 18 50 10 [email protected] www.dresden-elektronik.de

Page 2 of 25

User Manual

Version 01.01

2011-07-01


Document history

Date Version

2011-06-29 01.00

2011-07-01 01.01

Description

Initial version

Update

- Certification 2.4GHz usb radio stick

- Working temperature

- Radio data

Mailing list

Firm

DE

Division / Name

A.Palm

Author / Check / Release

Author

Check release

Firm

DE

Division / Name

Dev. / A.Palm dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 3 of 25

User Manual

Version 01.01

2011-07-01


Abbreviations

Abbreviation Description

PWM

RF

SPI

TWI

UART

USART

USB

WPAN

ADC

AES

CE

DAC

ETSI

FCC

GPIO

IC

ISM

JTAG

MAC

MCU, µC

Analog to Digital Converter

Advanced Encryption Standard

(Applications) - Consumer Electronics

Digital to Analog Converter

European Telecommunications Standards Institute

Federal Communications Commission

Generals Purpose Input Output

(Certification) - Industry Canada

Industrial, Scientific and Medical frequency band

Joint Test Action Group

Medium Access Control

Microcontroller Unit

Pulse Width Modulation

Radio Frequency

Serial Peripheral Interface

Two-Wire Serial Interface

Universal Asynchronous Receiver Transmitter

Universal Synchronous/Asynchronous Receiver Transmitter

Universal Serial Bus

Wireless Personal Area Network dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 4 of 25

User Manual

Version 01.01

2011-07-01


1. Overview

The compact designed USB radio sticks deRFusb-23E00 and deRFusb-13E00 contain a powerful CORTEX-M3 microcontroller with 256 kBytes High-Speed Flash. Additional flash memory to store user defined data is provided using the USB radio sticks deRFusb-23E06 and deRFusb-13E06, it is usable as mass storage device.

Depending on the transmission frequency of 2.4 GHz - deRFusb-23E00/06/JTAG - or

868/915 MHz - deRFusb-13E00/06/JTAG - the ATMEL low-power transceivers AT86RF231 or alternatively AT86RF212 are integrated. They provide a complete radio transceiver interface between the antenna and the microcontroller and an extended functional range such as a 128-Bit AES hardware engine to assure data security.

The USB radio sticks provide a programming and debugging interface to the user, by default via USB. For programming via JTAG, the variants deRFusb-23E00 JTAG, deRFusb-23E06

JTAG, deRFusb-13E00 JTAG and deRFusb-13E06 JTAG are available.

2. Application

The main applications for the USB radio sticks deRFusb-23E00/06/JTAG and deRFusb-

13E00/06/JTAG are:

•

2.4GHz and Sub-GHz range IEEE 802.15.4

•

ZigBee

®

Pro

•

ZigBee

®

RF4CE

•

ZigBee

®

IP

• 6LoWPAN

• SP100

• Wireless Sensor Networks (WSN)

• industrial and home controlling and monitoring

3. Features

The USB radio sticks deRFusb-23E00/JTAG and deRFusb-23E06/JTAG offer the following features:

• compact size (in case): 71.0 x 23.0 x 8.7 mm

•

USB powered

• 3 free programmable status LEDs

• RF shielding

• Debugging/Programming interfaces: 1 x DBGU (Debug-Unit) or 1 x JTAG with 10 pin connector mounting (option ‘JTAG’), USB dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 5 of 25

User Manual

Version 01.01

2011-07-01


•

Onboard transceiver and chip ceramic antenna 2.4GHz

•

Optional: onboard 2 GByte flash (option ‘06’)

•

Certification: FCC certified, IC pending, conformity ETSI/CE dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 6 of 25

User Manual

Version 01.01

2011-07-01


The block diagram below shows layout and interaction of the main deRFusb-23E00/06/JTAG components:

VUSB

4.5 .. 5.5V

VCC

VCC

3.3V

JTAG

DBGU

USB

VUSB

4.5 .. 5.5V

ATSAM3S4BA

VCC

SPI

AT86RF231 Chip antenna

MMC

Option: 2 GByte Flash

Figure 1: block diagram deRFusb-23E00/06/JTAG

The deRFusb-13E00/06/JTAG offer the same features like the deRFusb-23E00/06/JTAG except the built-in Sub-GHz transceiver and onboard Sub-GHz chip antenna.

•

Onboard transceiver and chip ceramic antenna for Sub-GHz

Layout and interaction of the main deRFusb-13E00/06/JTAG components:

VCC

3.3V

JTAG

DBGU

USB

ATSAM3S4BA

SPI

AT86RF212

MMC

Option: 2 GByte Flash

Figure 2: block diagram deRFusb-13E00/06/JTAG

Chip antenna dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 7 of 25

User Manual

Version 01.01

2011-07-01

4. Technical data


Table 1: Mechanical data

Mechanical

Radio module

Size (length x width x height) 71.0 x 23.0 x 8.7 mm (in case)

63.5 x 19.0 x 5.5 mm (without case)

63.5 x 19.0 x 9.5 mm (with JTAG, without case)

Connectors

USB chassis plug type A

10 pin header - connection option

‘JTAG’

2 x 5 pins, 1.27 mm pitch

Table 2: Environment

Temperature and humidity range

Working area T_work w/o external flash

1

T_work with external flash

2

Min

- 40

- 25

Working area 25

1

valid for deRFusb23E00/JTAG and deRFusb13E00/JTAG

2

valid for deRFusb23E06/JTAG and deRFusb13E06/JTAG

Table 3: Electrical data

Electrical (VUSB = 5.0VDC)

Parameter

Supply voltage

Current consumption

VUSB

I_TXon (TX_PWR = 3)

I_TXoff

I_sleep

I_RXon dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Min

4.5

Typ

Typ

5.0

51

32

TBD

TBD

Max

+85 °C

+85 °C

80

Max

Unit

% r.H.

Unit

5.5 VDC mA mA mA mA

Page 8 of 25

User Manual

Version 01.01

2011-07-01

Table 4: Radio data transmission


Radio (VUSB = 5.0VDC)

Parameter / feature deRFusb-23E00/06/JTAG

Antenna Chip ceramic

Antenna gain

Min Typ Max Unit

Antenna diversity: no

Range

Frequency range line of sight

Transmitting power conducted

TX_PWR = 0

Receiver sensitivity

Data rate

+1.3

- 0.5

>200

2.4

+3.0

- 101

250

500

1

2 dBi (peak) dBi (average) m

GHz dBm dBm kb/s kb/s

Mb/s

Mb/s deRFusb-13E00/06/JTAG

Antenna Chip ceramic

Antenna gain

Range

Frequency range

Antenna diversity: no line of sight

Transmitting power conducted

Receiver sensitivity

TX_PWR = 0 @ 915MHz

TX_PWR = 0 @ 868MHz

Data rate

- 0.7

- 2.6

>200

868

915

+ 9.0

+ 5.0

- 110

20

40

250

500

1 dBi (peak) dBi (average) m

MHz (band) dBm dBm kb/s kb/s kb/s kb/s

Mb/s dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 9 of 25

User Manual

Version 01.01

2011-07-01

5. Mechanical size


63.5 mm

height 5.5 mm

Figure 3: Size deRFusb-23E00 and deRFusb-23E06

Placed in case the mechanical size is 71.0 x 23.0 x 8.7 mm (length x width x height).

These dimensions are the same at the deRFusb-13E00 and deRFusb-13E06 radio sticks.

Figure 4: deRFusb-13E00 and deRFusb-13E06

The connector for all radio stick design versions is USB type A.

Figure 5: USB type A connection dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 10 of 25

User Manual

Version 01.01

2011-07-01


6. Pin assignment

The optional 10 pin connector offers the programming interface (JTAG) and debugging interface (Debug RXD and Debug TXD) to the user. It is directly accessible from the USB stick bottom side.

Figure 6: Top and bottom overlay deRFusb-23E00, deRFusb-23E06, deRFusb-23E00 JTAG and deRFusb-23E06 JTAG

X2 pins: 2 .... 10

1 ..... 9

1.27 mm pitch

Figure 7: optional 10 pin connector with footprint receptacle dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 11 of 25

User Manual

Version 01.01

2011-07-01


Figure 8: Top overlay deRFusb-13E00, deRFusb-13E06, deRFusb-13E00 JTAG and deRFusb-

13E06 JTAG

X2 pins: 2 .... 10

1 ..... 9

1.27 mm pitch

Figure 9: Optional 10 pin connector with footprint receptacle dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 12 of 25

User Manual

Version 01.01

2011-07-01


Table 5: Pin assignment of deRFusb-23E00/06/JTAG and deRFusb-13E00/06/JTAG

µC Pin name function comments

35

34

32 PA7/RTS0/PWMH3/XIN32

Internal transceiver interface

28

47

23

36

39

30

33

20

11

21

27

22

53

49

51

USB connector

56

57

DDM

DDP

USB DM

USB DP

10 pin connector (only available with option ‘JTAG’)

PB7/TCK/SWCLK

GND

VCC

PB6/TMS/SWDIO

JTAG TCK

PB5/TWCK1/PWML0/WKUP13/TDO JTAG TDO

JTAG TMS

NRST

VCC

PA9/URXD0/NPCS1/PWMFI0

PB4/TWD1/PWMH2/TDI

29 PA10/UTXD0/NPCS2

Miscellaneous

13

9

10

PA19/RK/PWML0/A15/AD2

PA17/TD/PCK1/PWMH3/AD0

PA18/RD/PCK2/A14/AD1

PA5/RXD0/NPCS3

PA6/TXD0/PCK0

PA15/TF/TIOA1/PWML3

PA21/RXD1/PCK1/AD8

PA14/SPCK/PWMH3

PA12/MISO/PWMH1

PA13/MOSI/PWMH2

PA11/NPCS0/PWMH0

PA1/PWMH1/TIOB0/A18

PA24/RTS1/PWMH1/A20

PA4/TWCK0/TCLK0

2 GByte flash memory

42 MCDA0

52

26

MCDA1

MCDA2

37

38

MCDA3

MCCDA

/Reset

Debug RXD

JTAG TDI

Debug TXD

LED1

LED2

LED3

Hardware ID1

Hardware ID2

Hardware ID3

RXTS/DIG2

SLP-TR

SCK

MISO

MOSI

SELN

IRQ

RST

CLKM ext. Flash Data 0 ext. Flash Data 1 ext. Flash Data 2 ext. Flash Data 3 ext. Flash Command pin 1 pin 2 pin 3 pin 4 pin 5 pin 6 pin 7 pin 8 pin 9 pin 10 red yellow green

Timestamp

SPI

SPI

SPI

Transceiver Reset dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 13 of 25

User Manual

Version 01.01

2011-07-01


41

Erase pin

MCCK

55 PB12/PWML1/ERASE ext. Flash Clock

Table 6: Signal description list

Signal name Function

Power - USB connector

DDM

DDP

JTAG

TCK

USB Full Speed Data –

USB Full Speed Data +

Test Clock

TDI

TDO

TDM

Reset

RSTN

UART0

URXD0

UTXD0

Test Data In

Test Data Out

Test Mode Select

Microcontroller Reset

UART Receive Data

UART Transmit Data

Type Active level

Comments

Analog

Digital

Input

Input

Output

Input

I/O

Input

Output

Low onboard Pull-up onboard Pull-up onboard Pull-up

Pull-Up resistor dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 14 of 25

User Manual

Version 01.01

2011-07-01


7. Programming

7.1. JTAG interface

Only the deRFusb-23E00 JTAG, deRFusb-23E06 JTAG, deRFusb-13E00 JTAG and deR-

Fusb-13E06 JTAG can be programmed over JTAG interface (TDI, TDO, TCK, TMS) with a suitable JTAG-programmer for ARM-based microcontrollers.

7.2. USB interface

The alternative programming feature for the deRFusb radio sticks is provided by the USB interface.

The interface represents a USB 2.0 Full-Speed Device (not USB certified). The USB interface logs on at the host as Mass Storage Device and as deRFusb-xxxx.

For a more details of the interface please refer to the ATSAM3S ATMEL data sheet:

•

Preliminary PDF: doc6500.pdf

•

Preliminary Summary PDF: 6500s.pdf http://www.atmel.com/dyn/products/product_docs.asp?category_id=163&family_id=605&subf amily_id=2127&part_id=4691

7.3. Required hardware

JTAG interface

For the JTAG interface Dresden elektronik ingenieurtechnik gmbh offers the hardware components for a fast start-up. The following hardware setups are possible:

1. Option ATMEL SAM-ICE programmer

•

(A) deRFusb-23E00/06 JTAG or deRFusb-13E00/06 JTAG

•

(B) SAM-ICE-Adapter with onboard RS232 level shifter

• (C) SAM-ICE programmer

• (D) RS232 cable dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 15 of 25

User Manual

Version 01.01

2011-07-01


(C)

(A)

(D)

(B)

Figure 10: USB radio stick with SAM-ICE programmer

2. Option OLIMEX ARM programmer

•

(A) deRFusb-23E00/06 or deRFusb-13E00/06

•

(B) SAM-ICE-Adapter with onboard RS232 level shifter

•

(C) Olimex USB-ARM programmer

•

(D) RS232 cable

(C)

(A)

(D)

(B)

Figure 11: USB radio stick with OLIMEX ARM programmer

Attention: The SAM-ICE-Adapter has no own power supply! Connect the USB radio stick with an USB Type-A extension cable to a laptop or PC. dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 16 of 25

User Manual

Version 01.01

2011-07-01


USB interface

No additional hardware is necessary using the USB interface to program the deRFusb-

23E00/06 and deRFusb-13E00/06 radio sticks.

7.4. Programming and debugging details

For programming via JTAG there are two alternatives:

•

OpenOCD

•

Segger J-Link or Atmel SAM-ICE.

OpenOCD

A suitable on chip debug system including flash programming and SRAM debugging support is available from various vendors e.g. http://www.olimex.com/dev/arm-usb-ocd.html

This open source programming software is recommended for open source toolchains.

Dresden elektronik ingenieurtechnik gmbh provides scripts for ease of use.

Segger J-Link or Atmel SAM-ICE

These In-Circuit-Emulators are commercially available programming adapters. They work well with e.g. the IAR embedded workbench. They are also working with the GDB debug server (for use with open source toolchain).

The programming and debugging features are license dependent.

Debugging and tracing - required hardware

Debugging and tracing of the USB radio sticks is possible with the SAM-ICE adapter. It has following features:

•

10 pin connector for deRFusb-23E00/06 JTAG and deRFusb-13E00/06 JTAG

•

20 pin connector for ARM JTAG programmer

• 6 pin connector for ARM Debug-Unit

• RS232 connector with onboard RS232 level shifter for ARM Debug-Unit

Troubleshooting

The ERASE pin (see section 6) is used to reinitialize the Flash content - and some of its

NVM (Non-Volatile Memory) bits - to an erased state. The flash is transferred to its original state.

The pin must be tied high during more than 220 ms to perform a Flash erase operation. dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 17 of 25

User Manual

Version 01.01

2011-07-01

8. Onboard transceiver


The main difference between the deRFusb-23E00/06/JTAG and the deRFusb-

13E00/06/JTAG USB radio sticks is the built-in 2.4GHz or alternatively Sub-GHz transceiver in combination with the appropriate onboard chip antenna.

deRFusb-23E00/06/JTAG - AT86RF231 transceiver

The low-power 2.4GHz transceiver is designed for industrial and consumer IEEE 802.15.4,

ZigBee

®

, RF4CE, SP100 and high data rate ISM applications.

deRFusb-13E00/06/JTAG - AT86RF212 transceiver

The low-power, low-voltage 800/900MHz transceiver is designed for low-cost IEEE 802.15.4,

ZigBee

®

and high data rate ISM applications available Europe and North America.

General transceiver description

These single-chip radio transceivers provide a complete radio transceiver interface between an antenna and a microcontroller.

They comprise the analog radio transceiver and the digital modulation and demodulation including time and frequency synchronization and data buffering. The number of external components is minimized such that only the antenna, the crystal and decoupling capacitors are required. The bidirectional differential antenna pins are used for transmission and reception, thus no external antenna switch is needed.

An internal 128 byte RAM for RX and TX buffers the data to be transmitted or the received data. Two on chip low dropout voltage regulators provide the internal analog and digital 1.8V supply.

The transceivers further contain comprehensive hardware-MAC support (Extended Operating Mode) and a security engine (AES) to improve the overall system power efficiency and timing.

9. Onboard flash (option)

A 2 GByte flash memory to store user defined data is optionally available using the deRFusb-

23E06/JTAG and deRFusb-13E06/JTAG USB radio sticks.

This flash memory is typically applied as mass storage device for user data. It works like a

Multimedia Card (MMC). Possible data bit modes are 1bit (default) and 4bit.

The flash is equipped with a memory controller and has a NAND flash architecture. It complies with eMMC Specification Version 4.4. The temperature range for safe operation is from

- 25C° to +85C°. dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 18 of 25

User Manual

Version 01.01

2011-07-01


10. Radio certification

10.1. United States (FCC)

The deRFusb-23E00/06/JTAG and deRFusb-13E00/06/JTAG USB radio sticks comply with the requirements of FCC part 15.

The FCC certification for deRFusb-13E00/06/JTAG is pending.

To fulfill FCC Certification requirements, an OEM manufacturer must comply with the following regulations:

The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, the outside of the device into which the module is installed must also display a label referring to the enclosed module.

This exterior label can use wording such as the following. Any similar wording that expresses the same meaning may be used.

Sample label for USB radio stick deRFusb-23E00, deRFusb-23E06,

deRFusb-23E00 JTAG and deRFusb-23E06 JTAG:

FCC-ID: XVV-ARM323E00

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: The usb radio sticks deRFusb-23E00 JTAG, deRFusb-23E06 and deRFusb-23E06

JTAG fulfill a Permissive Change Class 1 regarding to FCC Section 2.1043 and complies with the requirements of FCC part 15.

The Original Equipment Manufacturer (OEM) must ensure that the OEM modular transmitter is labeled with its own FCC ID number. This includes a clearly visible label on the outside of the final product enclosure that displays the contents shown below. If the FCC ID is not visible when the equipment is installed inside another device, the outside of the device into which the equipment is installed must also display a label referring to the enclosed equipment.

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

(FCC 15.19). The internal / external antenna(s) used for this mobile transmitter must provide a separation distance of at least 20 cm from all persons and must not be co-located or operate in conjunction with any other antenna or transmitter.

Installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This device is approved as a mobile dedresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 19 of 25

User Manual

Version 01.01

2011-07-01

USB radio sticks deRFusb vice with respect to RF exposure compliance, and may only be marketed to OEM installers.

Use in portable exposure conditions (FCC 2.1093) requires separate equipment authorization.

Modifications not expressly approved by this company could void the user's authority to operate this equipment (FCC section 15.21).

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

•

Increase the separation between the equipment and receiver

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

•

Consult the dealer or an experienced radio/TV technician for help

10.2. European Union (ETSI)

The deRFusb-23E00/06/JTAG and deRFusb-13E00/06/JTAG USB radio sticks have been tested compliant for use in the European Union countries.

If the deRFusb-23E00/06/JTAG and deRFusb-13E00/06/JTAG USB radio sticks are incorporated into a product, the manufacturer must ensure compliance of the final product to the European harmonized EMC and low-voltage/safety standards. A Declaration of Conformity must be issued for each of these standards and kept on file as described in Annex II of the

R&TTE Directive.

The manufacturer must maintain a copy of the deRFusb-23E00/06/JTAG and deRFusb-

13E00/06/JTAG USB radio sticks documentation and ensure the final product does not exceed the specified power ratings, antenna specifications, and/or installation requirements as specified in the user manual. If any of these specifications are exceeded in the final product, a submission must be made to a notified body for compliance testing to all required standards.

The “CE“ marking must be affixed to a visible location on the OEM product. The CE mark shall consist of the initials "CE" taking the following form:

•

If the CE marking is reduced or enlarged, the proportions given in the above graduated drawing must be respected. dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 20 of 25

User Manual

Version 01.01

2011-07-01


•

The CE marking must have a height of at least 5mm except where this is not possible on account of the nature of the apparatus.

•

The CE marking must be affixed visibly, legibly, and indelibly.

More detailed information about CE marking requirements you can find at "DIRECTIVE

1999/5/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL" on 9 March 1999 at section 12. dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 21 of 25

User Manual

Version 01.01

2011-07-01


11. Ordering information

The product name includes the following information: deRF xxxx - x x x xx x

Revision

Features

Size

Flash Memory

Frequency Range

Product / Chipset

Table 7: product name code

Product name code

Information

Product / Chipset

Frequency range

Flash memory

Size

Features

Revision

3

E

00

06

Code usb

1

2

JTAG

<blank>

Explanation

AT91SAM7S

868/915 MHz

2.4 GHz

Comments

USB radio stick

256 kByte

USB stick chip antenna onboard chip antenna, 2 GB flash onboard

10 pin connector

Rev 0

JTAG + DEBUG dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 22 of 25

User Manual

Version 01.01

2011-07-01

Table 8: ordering information


Ordering information

Part number Product name coming soon deRFusb-23E00

BN-032310 deRFusb-23E00 JTAG coming soon deRFusb-23E06 coming soon deRFusb-23E06 JTAG coming soon deRFusb-13E00 coming soon deRFusb-13E00 JTAG coming soon deRFusb-13E06 coming soon deRFusb-13E06 JTAG

BN-028337 SAM-ICE-Adapter

Comments

USB radio stick for 2.4 GHz

(delivered with a fitting case)

USB radio stick for 2.4 GHz with assembled JTAG connector

USB radio stick for 2.4 GHz with 2 GByte flash - (delivered with a fitting case)

USB radio stick for 2.4 GHz with 2 GByte flash with assembled JTAG connector

USB radio stick for Sub-GHz

(delivered with a fitting case)

USB radio stick for Sub-GHz with assembled JTAG connector

USB radio stick for Sub-GHz with 2 GByte flash - (delivered with a fitting case)

USB radio stick for Sub-GHz with 2 GByte flash with assembled JTAG connector program and debug interface adapter for

USB radio sticks dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 23 of 25

User Manual

Version 01.01

2011-07-01


12. Revision notes

Up to now for the deRFusb-23E00/06/JTAG and deRFusb-13E00/06/JTAG USB radio sticks technical problems, malfunctions or any other critical issues are not known. dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 24 of 25

User Manual

Version 01.01

2011-07-01

USB radio sticks deRFusb dresden elektronik ingenieurtechnik gmbh

Enno-Heidebroek-Straße 12

D-01237 Dresden

GERMANY

Tel. +49 351 - 31 85 00 | Fax +49 351 - 318 50 10

E-Mail [email protected]

General manager: Dipl.-Ing. L. Pietschmann

Commercial Registry: HRB 749 Dresden Municipal Court

Tax number: 201/107/00726

Sales tax identification number: DE 140125678

Trademarks and acknowledgements

• ZigBee® is a registered trademark of the ZigBee Alliance.

• 802.15.4™ is a trademark of the Institute of Electrical and Electronics Engineers (IEEE).

These trademarks are registered by their respective owners in certain countries only. Other brands and their products are trademarks or registered trademarks of their respective holders and should be noted as such.

Disclaimer

This note is provided as-is and is subject to change without notice. Except to the extent prohibited by law, dresden elektronik ingenieurtechnik gmbh makes no express or implied warranty of any kind with regard to this guide, and specifically disclaims the implied warranties and conditions of merchantability and fitness for a particular purpose. dresden elektronik ingenieurtechnik gmbh shall not be liable for any errors or incidental or consequential damage in connection with the furnishing, performance or use of this guide.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or any means electronic or mechanical, including photocopying and recording, for any purpose other than the purchaser’s personal use, without the written permission of dresden elektronik ingenieurtechnik gmbh.

Copyright © 2011, dresden elektronik ingenieurtechnik gmbh. All rights reserved. dresden elektronik ingenieurtechnik gmbh



Tel.: 0351 – 31 85 00


Page 25 of 25

dresden elektronik deRFusb-13E06 User manual

User Manual

USB Radio Sticks

Document Version V01.01

2011-07-01

Table of contents

Document history

Mailing list

Author / Check / Release

Abbreviations

1. Overview

2. Application

3. Features

4. Technical data

5. Mechanical size

6. Pin assignment

7. Programming

7.1. JTAG interface

7.2. USB interface

7.3. Required hardware

JTAG interface

USB interface

7.4. Programming and debugging details

OpenOCD

Segger J-Link or Atmel SAM-ICE

Debugging and tracing - required hardware

Troubleshooting

8. Onboard transceiver

deRFusb-23E00/06/JTAG - AT86RF231 transceiver

deRFusb-13E00/06/JTAG - AT86RF212 transceiver

General transceiver description

9. Onboard flash (option)

10. Radio certification

10.1. United States (FCC)

10.2. European Union (ETSI)

11. Ordering information

12. Revision notes

Trademarks and acknowledgements

Disclaimer

Related manuals

dresden elektronik ingenieurtechnik gmbh

XVV-ARM323E00

OLIMEX

SAM3-P256

OLIMEX

SAM3-H256

dresden elektronik ingenieurtechnik gmbh

XVV-MEGA22M00