Volvo 2002 S80 Specifications

VOLVO
TP 7809 (English). AT 0520. Printed in Sweden, Elanders Infologistics Väst AB, Mölnlycke 2005
OWNERS MANUAL S80
WEB EDITION
2006
Contents
An alphabetical index is at the back of the book.
In addition to describing the standard equipment this manual also
covers optional and extra equipment. In addition there are also
equipment alternatives, manual or automatic transmission for
example. In certain countries statutory requirements affect the level
of equipment. This means that it is occasionally necessary to page
past sections of the book which describe equipment not installed
on your car.
The specifications, design features and illustrations in this Owner’s
Manual are not binding. We reserve the right to make modifications
without prior notice.
© Volvo Car Corporation
Safety
9
Instruments, switches, controls
31
Climate control
53
Interior
65
Locks, alarm
77
Starting and driving
87
Wheels and tyres
117
Fuses, bulb replacement
125
Car care and Service
137
Specifications
155
Audio
167
Telephone
187
Index
201
1
Dashboard - left-hand drive
Temperature gauge .................. 32
Speedometer ........................... 32
Odometer ................................ 32
Trip odometer ......................... 32
Warning symbols .................... 33
Display ................................... 37
Tachometer .............................. 32
Automatic gearbox ................. 32
Clock ...................................... 32
Outside temperature sensor .... 32
Fuel gauge .............................. 32
Hazard warning flashers ..... 46
Electronic climate control ECC ........................... 56
Manual climate control A/C ................................ 60
Seat heating ......................................................... 46
Defroster - rear window, door mirrors ............... 46
Main/Dipped beam .................. 42
Position/Parking lamps ............ 42
Fog lamps ................................ 42
Instrument lighting .................. 42
Beam length control ................. 42
Steering wheel adjustment ....
Airbag ...................................
Cruise control .......................
Radio keypad ........................
Windscreen washers/wipers ..
Direction indicator lever .......
Trip computer .......................
2
43
12
41
173
44
43
40
Radio ..... 167
8501984d
Dashboard - right-hand drive
Hazard warning
flashers ....................... 46
Temperature gauge .................. 32
Speedometer ........................... 32
Odometer ................................ 32
Tripodometer .......................... 32
Warning symbols .................... 33
Display ................................... 37
Tachometer .............................. 32
Automatic gearbox ................. 32
Clock ...................................... 32
Outside temperature sensor .... 32
Fuel gauge .............................. 32
Main/Dipped beam .................. 42
Position/Parking lamps ............ 42
Fog lamps ................................ 42
Instrument lighting .................. 42
Beam length control ................. 42
Radio ..... 167
Electronic climate control ECC ........................... 56
Manual climate control A/C ................................ 60
Seat heating ......................................................... 46
Defroster - rear window, door mirrors ............... 46
8502061d
Steering wheel adjustment ....
Airbag ...................................
Cruise control .......................
Radio keypad ........................
Windscreen washers/wipers ..
Direction indicator lever .......
Trip computer .......................
43
12
41
173
44
43
40
3
Interior - left-hand drive
Doors and Locks .....................
Alarm .......................................
Power windows ......................
Power mirror controls .............
78
83
48
49
Glovebox ................ 70
Manual gearbox ....................
Automatic gearbox ...............
Geartronic .............................
Handbrake ............................
Switches in centre console ...
8502000d
Tipping backrests forward ....... 74
Hatch for long loads ................. 74
Tilting head restraints forward ... 39
Adjusting head restraints .......... 67
Child locks ................................ 82
Integrated booster cushion
for children ............................... 28
4
Manual adjustment of front seats ............ 66
Electrical adjustment of front seats .......... 68
Seat heating .............................................. 46
Cleaning the upholstery ........................... 141
91
92
93
47
38
Interior - right hand drive
Doors and Locks .....................
Alarm .......................................
Power windows ......................
Power mirror controls .............
78
83
48
49
Glovebox ................ 70
Manual gearbox ....................
Automatic gearbox ...............
Geartronic .............................
Handbrake ............................
Switches in centre console ...
91
92
93
47
38
8502062d
Manual adjustment of front seats ............ 66
Electrical adjustment of front seats .......... 68
Seat heating .............................................. 46
Cleaning the upholstery ........................... 141
Tipping backrests forward ....... 74
Hatch for long loads ................. 74
Tilting head restraints forward ... 39
Adjusting head restraints .......... 67
Child locks ................................ 82
Integrated booster cushion
for children ............................... 28
5
Exterior
Sunroof ........................ 50
Fuel filler flap ........................... 88
Refuelling ................................. 88
Economical driving ................... 89
Cleaning the car body .............. 140
Rustproofing ............................ 138
Touching up paintwork ............ 139
8000233d
Replacing main beam bulb ......... 132
Replacing dipped beam bulb ...... 132
Replacing position lamp bulb ..... 132
Replacing direction
indicator lamp bulb ..................... 133
Replacing fog lamp bulb ............ 134
6
Tyres ........................ 118
Wheels ..................... 118
Brakes ...................... 110
Spare wheel ............. 121
Changing wheels ..... 122
Boot lid ........................................................ 80
Replacing reversing lamp bulb ................... 133
Replacing brake lamp bulb .......................... 133
Replacing tail lamp bulb .............................. 133
Replacing direction indicator lamp bulb ...... 133
Replacing fog lamp bulb ............................. 133
Replacing number plate lighting .................. 135
Volvo Car Corporation and the environment
Volvo Car Corporation's
environmental philosophy
Environmental care, safety and quality are the
three core values of the Volvo Car Corporation.
They influence all operations. We also believe
that our customers share our consideration for
the environment.
Your Volvo complies with strict international
environmental standards and is also manufactured in one of the cleanest and most resourceefficient plants in the world. Volvo Car
Corporation has global certification to the ISO
14001 environmental standard. This leads to
continuous improvements within the area of the
environment.
EPI (Environmental Product Information)
environmental product declarations are supplied
for all Volvo models. You can now compare the
environmental impact of different models and
engines. Read more at www.volvocars.com/epi
Fuel consumption
Volvo cars have competitive fuel consumption
in each of their respective classes. The lower
the fuel consumption the lower the emission of
the greenhouse gas, carbon dioxide.
Efficient emission control
Your Volvo is manufactured following the
concept - Clean inside and out - a concept that
encompasses a clean interior environment as
well as highly efficient emission control. Your
car saves fuel and releases minimal quantities of
harmful substances.
Applied to the radiator is the PremAir®1 - a
catalytic coating which converts up to 75 % of
hazardous ground-level ozone into pure
oxygen.
1
PremAir® is a registered trademark of
Engelhard Corporation
Air cleaning in the passenger
compartment
A sophisticated air cleaning system, IAQS
(Interior Air Quality System)2 , option, ensures
that the air in the passenger compartment is
cleaner than the air outside.
The system consists of an electronic sensor and
a carbon filter. The air intake is closed if the
level of carbon monoxide in the passenger
compartment becomes too high - for example in
heavy town traffic, queues and tunnels. The
entry of nitrous oxides, ground-level ozone and
hydrocarbons is prevented by the carbon filter.
2
Option.
7
Volvo Car Corporation and the environment
Ecological standard for textiles
·
Textiles and leather inside the car fulfil the
requirements in accordance with the international ecological standard, Öko-Tex 1001.
Volvo workshops and the
environment
Regular maintenance carried out by an authorised Volvo workshop creates the conditions for
low fuel consumption and contributes to a
cleaner environment.
Volvo service technicians are equipped with the
knowhow and tools to ensure that your car
delivers the best possible environmental
performance.
Reducing environmental impact
You can help reduce environmental impact, for
example, by purchasing eco-labelled car care
products and by servicing and maintaining the
car according to the instructions in the owner’s
manual.
The following hints will help you to do your bit
for the environment:
·
Ensure that your tyre pressures are correct.
Poorly inflated tyres increase fuel consumption.
·
·
·
·
·
0000324
·
·
·
·
1
8
Does not apply to the S80 Executive
Since a roof rack and ski box increase air
resistance, leading to significantly higher fuel consumption, they should be
removed immediately after
use.
Remove unnecessary items from the car the greater the load the higher the fuel consumption.
Is your car equipped with an engine block
heater? If so, use it for a few hours before
starting from cold to reduce fuel consumption and exhaust emissions.
Drive gently. Avoid unnecessary rapid acceleration and heavy braking.
Drive in the highest gear possible. Low engine speeds result
in lower fuel consumption.
Ease back on the accelerator on
downhill gradients.
Use engine braking. Take your foot off the
accelerator and change down.
Avoid idling. Switch off the engine in traffic
queues.
Always dispose of environmentally hazardous waste, such as batteries and oils, in an environmentally safe manner. If
uncertain, consult your
Volvo workshop for advice.
Service your car regularly.
These hints will help you to reduce your fuel
consumption without increasing your travel
time or lessening the enjoyment of driving.
Apart from being kind to your car, you'll be
saving money - and the Earth's resources.
Safety
Seatbelts
10
Airbag (SRS)
12
Activating/deactivating the airbag (SRS)
16
Side airbags
18
Inflatable Curtain (IC)
20
WHIPS (Whiplash Protection System)
21
When are the safety systems activated?
23
Inspecting the airbags and inflatable curtains
24
Child safety
25
9
Seatbelts
Seatbelt tensioner
Ar4mp
E5
040413
Ar4mp
e5
1695
DOT
IMPORTEDBYVOLVONORTH
All the seatbelts are equipped with belt
tensioners. A mechanism in the belt tensioner
tightens the belt around the body in the event of
a sufficiently violent collision. This provides
more effective restraint for passengers.
AMERICACORP.ROCKLEIGHNJ.
BELTNO.XXXXXX
VOLVOGOTHENBURG
MADEINSWEDEN
DATEOFMANUFACTURE
YEAR WEEKDAY
02
3
6
8801947d
8505253a
Tensioning the hip strap. The belt must be
positioned low down
Label on seatbelts with seatbelt tensioner
Always use a seatbelt
The belt locks and cannot be withdrawn:
• if it is pulled out too quickly
• during braking and acceleration
• if the car leans heavily.
It is important that the belt lies against the body
so it can provide maximum protection. Do not
lean the backrest too far back. The seatbelt is
designed to protect in a normal seating position.
Keep the following in mind:
• do not use clips or anything else that can
prevent the belt from fitting properly
• ensure the belt is not twisted or caught on
anything
• the hip strap must be positioned low down
(not over the abdomen)
• tension the hip strap over the lap by pulling
the diagonal shoulder belt as illustrated.
Heavy braking can have serious consequences
if the seatbelts are not used. Ensure that all
passengers use their seatbelts. Otherwise, rear
seat passengers may be thrown forward against
the backs of the front seats in a collision.
Putting on a seatbelt:
• Pull the belt out slowly and secure it by
pressing the buckle into the lock. A loud
”click” indicates that the belt has locked.
Releasing the belt:
• Press the red lock button and let the belt
retract. If the belt does not retract fully, feed
the belt in by hand so that it does not hang
loose.
10
WARNING!
• The seatbelts and airbags interact. If a
seatbelt is not used or is used incorrectly,
this may diminish the protection provided
by the airbag in the event of a collision.
• Each belt is intended for one person only.
• Never modify or repair the seatbelts
yourself. Contact an authorised Volvo
workshop.
• If the belt has been subjected to a major
load, such as in a collision, the entire belt
must be replaced. Some of the protective
characteristics of the belt may have been
lost, even if it appears to be undamaged.
Replace the seatbelt if the belt is worn or
damaged. The new seatbelt must be typeapproved and intended for installation in
the same position as the replaced belt.
Seatbelts
8803443a
8802849r
Seatbelt reminder
Seatbelts and pregnancy
The seatbelt warning symbol in the combined
instrument panel and above the rearview mirror
comes on until the driver and front seat
passenger buckle their seatbelts. The seatbelt
reminder switches off after 6 seconds if speed
is below 10 km/h. If the driver or front seat
passenger have not buckled their seatbelts, the
reminder switches on again when the speed
exceeds 10 km/h and switches off if the speed
drops below 5 km/h. If the belt is released, the
function reactivates when the speed exceeds
10 km/h.
The seatbelt reminder is intended for an adult
sitting in the front seat. If a belt-fitted child seat
is fitted in the front seat, the seatbelt reminder
does not switch on.
The seatbelt should always be worn during
pregnancy. But it is crucial that it be worn in the
correct way. The diagonal section should wrap
over the shoulder then be routed between the
breasts and to the side of the belly. The lap
section should lay flat over the thighs and as
low as possible under the belly. It must never
be allowed to ride upward. Remove all slack
from the belt and insure that it fits close to the
body without any twists.
As a pregnancy progresses, pregnant drivers
should adjust their seats and steering wheel
such that they can easily maintain control of the
vehicle as they drive (which means they must
be able to easily operate the foot pedals and
steering wheel). Within this context, they
should strive to position the seat with as large a
distance as possible between their belly and the
steering wheel.
11
Airbag (SRS)
As well as the warning symbol, a
message appears in the information
display. If the warning symbol
malfunctions, the warning triangle
comes on and the message SRS
AIRBAG SERVICE URGENT
appears in the display. Contact an
authorised Volvo workshop
immediately.
WARNING!
3800639d
Warning symbol in combined
instrument panel
The Airbag system1 is monitored continuously
by the control module and there is a warning
lamp in the combined instrument panel. This
lamp comes on when the ignition key is turned
to position I, II or III. The symbol goes out
after about 7 seconds if the Airbag system1 is
working correctly.
1. Includes SRS and seatbelt tensioner, SIPS and IC.
12
If the warning symbol for the Airbag
system remains on or comes on while
driving, it means that the Airbag system is
not functioning fully. The symbol can
indicate a fault in the seatbelt buckle, SIPS,
SRS or IC system. Contact an authorised
Volvo workshop immediately.
Airbag (SRS)
WARNING!
Never place a child in a child seat or on a
booster cushion in the front seat if the airbag
(SRS) is activated2.
Never allow a child to stand or sit in front of
the front passenger seat. No one shorter than
140 cm (4 ft 7) should sit in the front
passenger seat if the airbag (SRS) is
activated.
Failure to follow the advice given above can
endanger the life of the child.
2. For information on activated/deactivated airbag (SRS)
see page 16.
8801907e
Airbag (SRS) on the driver’s
side
The car has an SRS airbag (Supplemental
Restraint System) in the steering wheel to
supplement the protection afforded by the
seatbelt. This airbag is fitted folded up into the
centre of the steering wheel. The steering wheel
is marked SRS AIRBAG.
WARNING!
The seatbelts and airbags interact. If a
seatbelt is not used or is used incorrectly,
this may diminish the protection provided by
the airbag in the event of a collision.
8801889e
Passenger airbag (SRS)
The passenger airbag1 is fitted folded up behind
a panel above the glovebox. This panel is
marked SRS AIRBAG.
WARNING!
To minimise the risk of injury if the airbag
deploys, passengers must sit as upright as
possible with their feet on the floor and
backs against the backrest. Seatbelts must be
secured.
1. Not all cars have a passenger airbag (SRS). This can be
unselected when the car is ordered.
13
Airbag (SRS)
WARNING!
Repairs must only be performed by an
authorised Volvo workshop.
Work on the SRS system can cause
malfunction and result in serious personal
injury.
8803417d
SRS system, left-hand drive
SRS system
The SRS system consists of a gas generator
surrounded by an inflatable airbag. A sufficiently violent collision trips sensors and ignites the
gas generator, inflating the airbag with hot gas.
To cushion the impact, the airbag deflates when
compressed. When this occurs, smoke escapes
into the car. This is completely normal. The
entire process, including inflation and deflation
of the airbag, occurs within tenths of a second.
14
8803418d
SRS system, right-hand drive
NOTE!
• The sensors react differently depending on
the course of the collision and whether the
seatbelts on the driver and passenger side
are used. It is therefore possible that only
one (or none) of the airbags may inflate in a
collision. The SRS system senses the force
of the collision on the car and adapts
accordingly so that one or more airbags is
deployed.
• The airbags have a function whereby their
capacities are adapted to the collision force
to which the vehicle is subjected.
Airbag (SRS)
8802099m
8802092M
Location of the passenger airbag in left-hand
drive and right-hand drive cars
WARNING!
Never interfere with SRS components in the
steering wheel or the panel above the
glovebox.
Objects and accessories must not be
positioned or glued on or near the SRS
Airbag panel (above the glovebox) or in the
area affected by a deployed airbag.
15
Activating/deactivating the airbag (SRS)
WARNING!
8803406m
8803403m
Indicator showing that the passenger airbag
(SRS) is deactivated
PACOS (option)
The airbag (SRS) for the front passenger seat
can be deactivated. This is necessary if a child
seat is to be placed there.
Indicator
A text message in the rearview mirror indicates
that the passenger airbag (SRS) is deactivated.
PACOS (Passenger Airbag Cut-Off Switch)
Activating/deactivating
The switch is located on the passenger end of
the dashboard and is accessible when the
passenger door is open. Check that the switch
is in the required position. Volvo recommends
that that the ignition key is used to change
position. (Other items with a shape similar to a
key can be used).
WARNING!
If the car is equipped with a front passenger
airbag (SRS), but does not have PACOS, the
airbag will always be activated.
16
• Activated airbag (passenger seat):
Never place a child in a child seat or on a
booster cushion in the front passenger seat
when the airbag is activated. This also
applies to anyone shorter than 140 cm
(4 ft 7).
• Deactivated airbag (passenger seat):
No one taller than 140 cm (4 ft 7) should
sit in the front passenger seat when the
airbag is deactivated.
Failure to follow the advice given above can
endanger life.
Activating/deactivating the airbag (SRS)
WARNING!
Do not allow anyone to sit in the front
passenger seat if the text message in the roof
panel indicates that the airbag (SRS) is
deactivated and the airbag warning symbol is
displayed in the combined instrument panel.
This indicates that there has been a severe
malfunction. Contact an authorised Volvo
workshop as soon as possible.
8803405m
8803404m
Switch position
ON = Airbag (SRS) activated. With the switch
in this position, persons taller than 140 cm
(4 ft 7) can sit in the front passenger seat, but
never children in a child seat or on a booster
cushion.
OFF = Airbag (SRS) is deactivated. With the
switch in this position, children in a child seat
or on a booster cushion can sit in the front
passenger seat, but never persons taller than
140 cm (4 ft 7).
17
Side airbags
WARNING!
Do not put objects in the area between the
outside of the seat and the door panel, since
this area is required by the side airbag.
WARNING!
Use only Volvo genuine car seat covers, or
seat covers approved by Volvo. Other seat
covers may impede the operation of the side
air bags.
IMG-2011
8803041a
Side airbag locations
Side airbags - SIPS bags
A large proportion of the collision force is
transferred by the SIPS (Side Impact Protection
System) to the floor, roof, beams, pillars, and
other structural parts of the body. The side
airbags on the driver’s and front passenger seats
protect the chest area and are an important part
of the SIPS. The SIPS bag system consists of
two main parts, the side airbags and the
sensors. The side airbags are located in the front
seat backrests.
Inflated side airbag
WARNING!
Side airbags are a supplement to the SIPS
system. Always wear a seatbelt.
Child seats and side airbags
The side airbag does not diminish the protection
provided by the car to children seated in a child
seat or on a booster cushion.
A child seat or booster cushion can be placed
on the front passenger seat provided that the car
does not have an activated1 passenger airbag.
WARNING!
Repairs must only be performed by an
authorised Volvo workshop.
Work on the SIPS system can cause
malfunction and result in serious personal
injury.
1. For information on activated/deactivated airbag (SRS)
see page 16.
18
Side airbags
8803412j
Left-hand drive
8803413j
Right-hand drive
SIPS bag system
The SIPS bag system consists of a gas
generator, side airbag and sensors. A sufficiently violent collision trips the sensors and ignites
the gas generator, inflating the side airbag. The
airbag inflates between the occupant and the
door panel and thereby cushions the initial
impact while deflating. The side airbag is only
normally deployed on the side of the collision.
19
Inflatable Curtain (IC)
8801999d
8801966e
Properties
The inflatable curtain, IC (Inflatable Curtain), is
a supplement to the SIPS system. It is concealed in the headlining along both sides of the
roof and protects both front and rear seat
passengers. The inflatable curtain is activated by
the SIPS collision sensors if the car is hit from
the side. When deployed, the inflatable curtain
inflates. The inflatable curtain helps to prevent
the driver and passengers from striking their
heads on the inside of the car during a collision.
20
WARNING!
The inflatable curtain is a supplement to the
seatbelts. Always wear a seatbelt.
WARNING!
• Never hang or fasten anything on the roof
handles. The hook is only intended for light
outer garments (not for hard objects such
as umbrellas).
• Do not screw or fit anything to the
headlining, door pillars or side panels. This
could compromise the intended protection.
Only use Volvo genuine parts that are
approved for fitting in these areas.
• Do not load the car higher than 50 mm
under the top edge of the rear passenger
windows to avoid affecting the protection
of the inflatable curtain in the event of a
side collision.
WHIPS (Whiplash Protection System)
WHIPS system and child seats/
booster cushions
The WHIPS system does not diminish the
protection provided by the car to children seated
in a child seat or on a booster cushion.
Correct seating position
For the best possible protection, the driver and
front seat passenger should sit in the centre of
the seat with as little space as possible between
the head and the head restraint.
8504618a
Protection against whiplash
injury - WHIPS
The whiplash protection system (WHIPS)
consists of energy absorbing backrests and
specially designed head restraints for the front
seats. The system is actuated by a rear-end
collision, where the angle and speed of the
collision, and the nature of the colliding vehicle
all have an influence.
WARNING!
Properties of the seat
When the WHIPS system is deployed, the
front seat backrests fall backward to alter the
position of the driver and front seat passenger.
This diminishes the risk of whiplash injury.
WARNING!
Never modify or repair the seat or WHIPS
system yourself. Contact an authorised Volvo
workshop.
The inflatable curtain is a supplement to the
seatbelts. Always wear a seatbelt.
21
WHIPS (Whiplash Protection System)
WARNING!
• If a seat has been subjected to extreme
forces, such as due to a rear-end collision,
the WHIPS system must be checked by an
authorised Volvo workshop.
• Part of the WHIPS system’s protective
capacity may have been lost even if the
seats appear to be undamaged. Contact an
authorised Volvo workshop to have the
system checked even after a minor rear-end
collision.
8504619a
IMG-20410
Do not obstruct the WHIPS
system
WARNING!
Do not squeeze rigid objects between the rear
seat cushion and the front seat backrest.
Make sure you do not to obstruct the
function of the WHIPS system.
22
WARNING!
If a rear seat backrest is folded down, the
corresponding front seat must be moved
forward so that it does not touch the folded
backrest.
When are the safety systems activated?
System
Triggered
Seatbelt tensioner
In the event of a head-on collision and/or overturning.
Airbags SRS
In the event of a head-on collision1.
Side airbags
In the event of a side impact1.
Inflatable Curtain IC
In the event of a side impact or if the car overturns1.
WHIPS
In a rear-end collision1.
1. The bodywork of the car could be greatly deformed in a
collision without airbag deployment. A number of factors
such as the rigidity and weight of the object hit, the speed
of the car, the angle of the collision etc. affects how the
different safety systems of the car are activated.
If the airbags have been deployed, the following is recommended:
• Have the car transported to an authorised
Volvo workshop. Do not drive with
deployed airbags.
• Have an authorised Volvo workshop replace
components in the car’s safety systems.
• Always contact a doctor.
WARNING!
The Airbag control unit is located in the
centre console. If the centre console is
drenched with water or other liquid,
disconnect the battery cables. Do not attempt
to start the car since the airbags may deploy.
Have the car transported to an authorised
Volvo workshop.
WARNING!
Never drive with deployed airbags. They can
make steering difficult. Other safety systems
may also be damaged. The smoke and dust
created when the airbags are deployed can
cause skin and eye irritation after intensive
exposure. In case of irritation, wash with
cold water. The rapid deployment sequence
and airbag fabric may cause friction injury
and burns to the skin.
NOTE! The SRS, SIPS, IC and belt tensioner
systems are deployed only once during a
collision.
23
Inspecting the airbags and inflatable curtains
Inspection intervals
The decal on the door pillar(s) shows the dates
(year, month) when you should contact an
authorised Volvo workshop to inspect and, if
necessary, replace the airbags, belt tensioners
and inflatable curtains. If you have questions
concerning the systems, contact an authorised
Volvo workshop.
1. Driver airbag
2. Front passenger airbag
3. Side airbag on the driver’s side
4. Side airbag on the passenger side
5. Inflatable curtain on the driver’s side
6. Inflatable curtain on the passenger side
This decal is located in the rear left door
opening
24
Child safety
Volvo’s own child safety equipment is designed
for your car. Use Volvo genuine equipment to
best ensure that the mounting points and
attachments are correctly positioned and are
sufficiently strong.
You may place:
•
•
a child seat or booster cushion on the front
passenger seat, provided the passenger
airbag is not activated1.
a rear-facing child seat in the rear seat that
uses the back of the front seat as support.
8803040a
8503861m
Child seats and airbags are not compatible
Children should sit
comfortably and safely
Child seats and airbags (SRS)
Always place a child in the rear seat if the
passenger airbag (SRS) is activated1. A child in
a child seat on the front passenger seat may
suffer serious injury if the airbag deploys.
The position of a child in the car and the choice
of equipment is dictated by the child’s height
and weight, for more information see page 27.
Children who are shorter than 150 cm (4 ft 11)
must be carried in adequate child protection.
WARNING!
Persons shorter than 140 cm (4 ft 7) may
only sit in the front passenger seat if the
passenger airbag is deactivated.
NOTE! Regulations regarding the placement of
children in cars vary from country to country.
Check what laws apply.
Children of all ages and sizes must always sit
correctly secured in the car. Never allow a child
to sit on the knee of a passenger.
1. For information on activated/deactivated airbag (SRS)
see page 16.
25
Child safety
8904049b
8903808a
Decals on the end of the dashboard
WARNING!
Never place a child in a child seat or on a
booster cushion in the front seat if the airbag
(SRS) is activated1. Failure to follow this
advice could endanger the life of the child.
1. For information on activated/deactivated airbag (SRS)
see page 16.
26
Decal located on the car’s end cover
WARNING!
Never place a child in a child seat or on a
booster cushion in the front seat if the airbag
(SRS) is activated.
No one shorter than 140 cm (4 ft 7) should
sit in the front passenger seat if the airbag
(SRS) is activated.
Failure to follow the advice given above can
endanger the life of the child.
Decal located on the car’s end cover
(Australia only)
Child safety
Weight / Age
Front seat
Outer rear seats
Centre rear seat
<10 kg
(0-9 months)
1. Rear-facing child seat, secured with
seatbelt.
L: Type approval no. E5 03160
2. Rear-facing child seat, secured with
ISOFIX mounting.
L: Type approval no. E5 03162
3. Rear-facing child seat, secured with
seatbelt and straps.
L: Type approval no. E5 03135
1. Rear-facing child seat, secured with
seatbelt and support legs.
L: Type approval no. E5 03160
2. Rear-facing child seat, secured with
ISOFIX mounting and support legs.
L: Type approval no. E5 03162
3. Rear-facing child seat, secured with
seatbelt, support legs and straps.
L: Type approval no. E5 03135
1. Rear-facing child seat, secured with
seatbelt, support legs and straps.
L: Type approval no. E5 03135
9-18 kg
(9-36 months)
1. Rear-facing child seat, secured with
seatbelt.
L: Type approval no. E5 03161
2. Rear-facing child seat, secured with
ISOFIX mounting.
L: Type approval no. E5 03163
3. Rear-facing child seat, secured with
seatbelt and straps.
L: Type approval no. E5 03135
1. Rear-facing child seat, secured with
seatbelt and support legs.
L: Type approval no. E5 03161
2. Rear-facing child seat, secured with
ISOFIX mounting and support legs.
L: Type approval no. E5 03163
3. Rear-facing child seat, secured with
seatbelt, support legs and straps.
L: Type approval no. E5 03135
1. Rear-facing child seat, secured with
seatbelt, support legs and straps.
L: Type approval no. E5 03135
15-36 kg
(3-12 years)
1. Booster cushion with or without
backrest.
L: Type approval no. E5 03139.
1. Booster cushion with or without
backrest.
L: Type approval no. E5 03139
1. Booster cushion with or without backrest.
L: Type approval no. E5 03139
2. Integrated booster cushion.
B: Type approval no. E5 03140
WARNING!
Never place a child in a child seat or on a booster cushion in the front
seat if the airbag (SRS) is activated.
No one shorter than 140 cm (4 ft 7) should sit in the front passenger seat
if the airbag (SRS) is activated.
Failure to follow the advice given above can endanger the life of the
child.
L: Suitable for certain child seats in accordance with the list. Child seats
can be vehicle-specific, limited, semi-universal or universal.
B: Integrated and approved for this age group.
NOTE! For information on activated/deactivated airbag (SRS), see
page 16.
27
Child safety
GIF
A
C
B
8503861m
8503859d
Folding out the booster cushion
Integrated booster cushion (option)
Volvo’s integrated booster cushion for the
centre seat is specially designed to provide
optimum safety for children.
When used with the regular seatbelt, the booster
cushion is approved for children weighing
between 15 and 36 kg.
Folding out the booster cushion:
• Fold down the booster cushion.
• Pull apart the Velcro.
• Raise the upper section back into place.
Check that:
- the seatbelt is in contact with the child’s
body and is not slack or twisted.
- the belt lies correctly over the shoulder.
28
the lap belt is low over the pelvis for
optimum protection.
- the belt does not touch the child’s throat or
lie below the shoulder.
• Carefully adjust the position of the head
restraint to suit the child.
Folding in the booster cushion:
• Fold down the upper section (A).
• Fasten the Velcro (B).
• Raise the booster cushion into the rear seat
backrest (C).
8503860d
Folding in the booster cushion
-
NOTE! Make sure that both sections of the
booster cushion are secured with the Velcro
strap (B) before folding in. Otherwise the upper
section (A) can become trapped in the rear seat
backrest (C) when the booster cushion is folded
out again.
WARNING!
• Repair or replacement should only be
performed by an authorised Volvo workshop. Do not make any modifications or
additions to the booster cushion.
• If an integrated booster cushion has been
subjected to a major load, such as in
conjunction with a collision, the entire
booster cushion must be replaced. Even if
the booster cushion appears to be undamaged, it may not afford the same level of
protection. The booster cushion must also
be replaced if it is heavily worn.
Child safety
Fitting a child seat
Volvo has child safety products that are
designed for and tested by Volvo.
When using other products that are available on
the market, it is important to read the fitting
instructions included with the product.
• Do not attach the straps for the child seat to
the horizontal adjustment bar, springs, rails
or beams under the seat. Sharp edges can
damage the straps.
• Allow the back of the child seat to rest
against the dashboard. This applies to cars
without a passenger airbag, or where the
airbag is deactivated.
WARNING!
Never place the child seat in the front seat if
the car is equipped with an activated1 front
passenger airbag. If problems arise when
fitting child safety products, contact the
manufacturer for clearer instructions.
IMG-201180
ISOFIX fixture system for child
seats (option)
The outer rear seats have ISOFIX attachment
points for child seats. Contact a Volvo dealer for
further information on child safety equipment.
1. For information on activated/deactivated airbag (SRS)
see page 16.
29
30
Instruments, switches and controls
Combined instrument panel
32
Indicator and warning symbols
33
Messages in the display
37
Switches in the centre console
38
Trip computer
40
Cruise control
41
Lighting panel
42
Left-hand stalk switch, Steering wheel adjustment
43
Right-hand stalk switch
44
Ignition switch and steering wheel lock
45
Hazard warning flashers, Rear defroster, Heated seats
46
Parking brake, Electrical socket
47
Power windows
48
Rearview mirror/door mirrors
49
Power sunroof
50
Sun screen, Sun blinds
51
Laminated side windows (option), Water-repellent coating (option)
52
31
Combined instrument panel
15
3800838m
1
2
3
4 5 6 7
8 9 10 11 12 13
1. Temperature gauge
Displays the engine cooling system temperature. If the temperature is abnormally high and the
needle enters the red field a message is shown
in the display. Remember that extra lamps in
front of the radiator grille reduce the cooling
capacity with high outside temperatures and
high engine loads.
5. Cruise control indicator
See page 41.
2. Display
The display shows information and warning
messages.
8. Warning symbol
If a fault should occur, the symbol lights and a
message is shown in the display.
3. Speedometer
Shows the speed of the car.
9. Tachometer
Gives engine speed in thousands of revolutions
per minute (RPM). The needle on the tachometer must not enter the red field.
4. Tripodometer, T1 and T2
The tripodometer is used for measuring shorter
distances. The right hand digit gives 100 meter
units. Depress the button for more than
2 seconds to reset. Change between the trip
odometers using one short press on the button.
32
6. Odometer
The odometer indicates the total mileage of
the car.
7. Main beam on/off
14
11. Outside temperature gauge
Displays the outside temperature. When the
temperature lies between +2 °C and -5 °C, a
snowflake symbol is shown in the display. The
symbol warns of slippery road conditions.
When the car is or was stationary, the outside
temperature gauge may rend a higher reading
than is actual.
12. Clock
Turn the button to set the time.
13. Fuel gauge
When the lamp in the instrument panel lights,
approximately 8 litres of usable fuel remain in
the tank.
14. Indicator and warning symbols
10. Automatic gearbox indicator
The selected gearshift programme is displayed
here. If you have Geartronic automatic transmission and drive in manual mode, the current
manual gear is displayed.
15. Direction indicators - left /right
Indicator and warning symbols
Warning symbol
of dashboard
in centre
This symbol shines as an red or yellow light
depending on the severity of the fault discovered. See next page for more information!
Red symbol
Stop the car. Read the message in the display.
Symbol and message text are shown until the
error is rectified.
3800839m
The indicator and warning symbols light when
the ignition key is turned to driving position
(position II) before starting. This shows that the
symbols are functioning. When the engine is
started all the symbols go out.
If the engine is not started within 5 seconds all
and
.
the symbols go out except
Certain symbols may not have the function
indicated, depending on car equipment. The
symbol for the parking brake goes out when the
parking brake is released.
Yellow symbol
Read the message in the display. Rectify.
The message text is cleared using the READ
button, see page 37, or it disappears after
2 minutes.
NOTE!
When the message text "TIME FOR
REGULAR SERVICE" is shown, the symbol lamp and message text are cleared using
the READ button, or they disappear after
2 minutes.
33
Indicator and warning symbols
WARNING!
If both the BRAKE and ABS warning
symbols are lit up there is a risk that the rear
end will have a tendency to slide during
heavy braking.
If BRAKE and ABS warning
symbols light up at the same
time, there may be a problem
in the brake force distribution.
· Stop the car in a safe place and switch off
the engine.
· Start the car again.
· If both warning symbols go out the fault
was temporary and it is not necessary to
visit a workshop.
· If the warning symbols remain lit, check the
brake fluid reservoir level first.
· If the reservoir level is below MIN the car
should not be driven further. Have it towed
to an authorised Volvo workshop to check
the brake system.
· If the brake fluid level is normal and the
lamps remain lit, carefully drive the car to
the nearest authorised Volvo workshop to
have the brake system checked.
34
Warning - fault in brake system
If the BRAKE symbol lights up the
brake fluid level may be too low.
· Stop the car in a safe place and check the
brake fluid reservoir level.
· If the reservoir level is below MIN the car
should not be driven further. Have it towed
to an authorised Volvo workshop to check
the brake system.
Warning - fault in ABS system
If the ABS warning symbol lights up
the ABS system is not functioning.
The car’s normal braking system continues to
function normally but without the ABS
function.
· Stop the car in a safe place and switch off
the engine.
· Start the engine again.
· If the warning symbol goes out, the fault
was temporary and it is not necessary to
visit a workshop.
· If the warning symbol remains lit, drive
carefully to an authorised workshop to
check the ABS system.
Indicator and warning symbols
The indicator and warning symbols light when the ignition key is
turned to driving position (position II) before starting. This shows
that the symbols are functioning. When the engine is started all the
symbols go out. If the engine is not started within 5 seconds all the
symbols go out except
and
. Certain symbols may not
have the function indicated, depending on car equipment. The
symbol for the parking brake goes out when the parking brake is
released.
The symbol flashes
The SC function acts to prevent the car’s drive
wheels from spinning. The TC function acts to
improve the car’s traction.
The AYC function acts to prevent skidding.
3800839m
Stability system STC* and
DSTC*
The STC/DSTC system comprises several
different functions that are described in detail
on page 112.
The symbol lights and goes out
again after approx. two seconds
The symbol lights for a system check when the
car is started.
The warning symbol shines with a
steady amber glow
TRACTION CONTROL TEMPORARILY
OFF is shown on the information display
together with the symbol.
The TC function has been temporarily reduced
due to high brake temperature.
The function is automatically reactivated when
brake temperature returns to normal.
The warning symbol shines with a
steady amber glow
ANTI-SKID SERVICE REQUIRED is shown
on the information display together with the
symbol.
The STC or DSTC system has been deactivated
due to a fault.
· Stop the car in a safe place and switch off
the engine.
· Restart the engine.
If the warning symbol remains lit, drive to an
authorised Volvo workshop to have the system
checked.
Fault in the STC or DSTC system
If the symbol comes on and the additional text
"ANTI-SKID SERVICE REQUIRED" and
you have not deactivated any of the system, this
indicates a fault in a part of the system.
· Stop the car in a safe place and switch off the
engine. Start the car again.
· If the warning symbol goes out this was just
a temporary indication fault and you do not
need to visit a workshop.
· If the warning symbol remains on, drive to
an authorised Volvo workshop to check
the system.
* The STC and DSTC system is an option on
some markets
WARNING!
Under normal driving conditions, the
STC/DSTC system improves the car’s road
safety, but this should not be taken as a reason
to increase speed. Always follow the usual
precautions for safe cornering and driving on
slippery surfaces.
35
Indicator and warning symbols
The indicator and warning symbols light when the ignition key is
turned to driving position (position II) before starting. This shows
that the symbols are functioning. When the engine is started all the
symbols go out. If the engine is not started within 5 seconds all the
Fault in car emissions systems
Drive to a Volvo workshop to have it
checked.
symbols go out except
and
. Certain symbols may not
have the function indicated, depending on car equipment. The
symbol for the parking brake goes out when the parking brake is
released.
Rear fog lamp
The lamp lights up when the rear fog
lamp is on.
Fault in SRS
If the symbol remains lit or lights
while driving a fault has been found in
the SRS system. Drive to a Volvo workshop to
have it checked.
Parking brake applied
Remember that the light only
indicates that the parking brake is
applied, not how hard. Check by pulling the
lever! You must always pull it hard enough
for the brake to fasten in a “notch”.
Low oil pressure
If the lamp lights while driving,
engine oil pressure is too low. Stop
the engine immediately and check the engine oil
level.
Seat belt reminder
The lamp shines until the driver connects
his/her safety belt.
36
Trailer indicator lamp
Flashes when the car and trailer
direction indicators are in use.
If the lamp does not flash, one of the direction
indicators on the trailer or car is defective.
Generator not charging
If the lamp lights while driving,
there is probably a fault in the
electrical system. Contact a Volvo workshop.
Engine pre-heater (diesel)
The lamp lights to inform that the engine
is pre-heating. When the lamp goes out,
the car may be started. Only applies to dieselpowered cars.
Messages in the display
Messages in the display
Whenever a warning or indicator symbol lights up, a message is displayed. When you have
read and understood, press the READ button (A). Read messages are then erased from the
display and are put into the memory. The message remains in the memory until the fault is
remedied.
Very serious fault messages cannot be erased from the display. They remain in the
display until the fault is remedied.
A
NOTE! If a warning message interrupts when you, for example, are in the trip computer
menu or wish to use the telephone, you must first acknowledge the message by pressing the
READ button (A).
3800648d
Message
STOP SAFELY
STOP ENGINE
SERVICE URGENT
SEE MANUAL
SERVICE REQUIRED
FIX NEXT SERVICE
TIME FOR REGULAR SERVICE
1) OIL LEVEL LOW - FILL OIL*
2) OIL LEVEL LOW - STOP SAFELY*
2) OIL LEVEL LOW - STOP ENGINE*
2) OIL LEVEL LOW - SEE MANUAL*
Messages stored in the memory can be read again. Press the READ button (A) if you wish
to see the stored message. You can scroll through the messages in the memory by pressing
the READ button (A). Press the READ button (A) to return read messages to the memory.
Significance/Action
Stop and switch off the engine. Serious risk of damage.
Stop and switch off the engine. Serious risk of damage.
Take your car in for service immediately.
Consult your owner’s manual.
Take your car in for service as soon as possible.
Have your car checked at the next service interval.
When this message is shown, the car is due for a service. When the message is displayed is affected by the
distance travelled, number of months since last service and engine running time.
Low engine oil level. Check and remedy as soon as possible. See page 149 for more information.
Low engine oil level. Stop the car safely, switch off the engine and check the oil level. See page 149.
Low engine oil level. Stop the car safely, switch off the engine and check the oil level. See page 149.
Low engine oil level. Stop the car safely, switch off the engine and check the oil level. See page 149.
1) Shown together with an amber warning triangle.
2) Shown together with a red warning triangle.
* Only applies to engine variants with oil level sensor.
37
Switches in the centre console
3603559d
NOTE! The order of the buttons may vary.
Active chassis,
FOUR-C (option)
3603554m
Press the button to shift
between Comfort and Sport
mode. See also page 95.
BLIS - Blind Spot
Information System
(option)
3603680m
38
Press the button to deactivate
or reactivate the function.
See page 113 for further
information.
The STC/DSTC
system*
This button is used to reduce
or reactivate the functions in
the STC/DSTC system.
When the LED in the button
comes on, the STC/DSTC
system is activated (if no fault
arises).
NOTE! Hold the button
depressed for at least half a
second to reduce the function of the STC/
DSTC system. The LED in the button goes out
and the text ”STC SPIN CONTROL OFF” or
”DSTC SPIN CONTROL OFF” is shown in
the display.
* Option on some markets
Reduce the system if you must use a wheel of a
different dimension than the other wheels.
The STC/DSTC system is reactivated when the
engine is started.
3603546m
3603549m
WARNING!
Remember the driving characteristics of the
car change if you deactivate the STC/DSTC
system.
Switches in the centre console
Lowering outer
rear seat head
restraints (option)
- Turn the ignition key to
position I or II.
- Press the button to lower the rear head
restraints to improve visibility.
Do not lower the head restraints if either of the
outer seats is occupied.
The head restraints must be restored to an
upright position manually.
The head restraints must be in an upright
position for the rear seat backrests to be
lowered.
3603547m
The system is always
activated when the car is
started. Press the button to
deactivate/reactivate parking
assistance. See also page 96.
3603555m
This button is used to retract
the door mirrors if they are
folded out, or to fold them out
if they are retracted.
Do as follows if a door mirror has been
accidentally folded in or out:
- Manually fold the door mirror forward as
far as possible.
- Turn the ignition key to position II.
- Fold the door mirror inward and then outward
using the button. The door mirrors have now
returned to their original fixed positions.
Use this button if the auxiliary
lamps of the car are to light
together with the main beam or
if you wish to deactivate this function. The LED
in the button is lit when the function is active.
3603552m
Electric socket/
Cigarette lighter
(option)
Locking the
boot lid
(certain countries)
Press this button in order to
lock the boot lid. The boot lid
remains locked even if the doors are unlocked
manually with the master key, the master key
remote control or the service key.
3603548m
Retractable door
mirrors (option)
Auxiliary lamps
(accessory)
Parking assistance
(option)
Deactivating the
deadlock function1
and detectors
3603551m
Use this button if you wish to
switch off the deadlock
function (doors cannot be opened from the
inside when locked). This button can also be
used when deactivating the alarm system
movement and tilt detectors2. The LED lights
when the functions are deactivated.
The electric socket can be
used for various 12V
accessories, such as mobile phones or coolers.
The cigarette lighter is activated by pushing in
the button. Once the lighter is heated, the button
will pop out. Pull out the lighter to use it. For
reasons of safety, always keep the lighter in the
socket when it is not in use. The maximum
current is 10A.
3603563m
NOTE! The relative positions of the buttons
can vary.
3603550m
1. Certain countries 2. Option
39
Trip computer
Speed in miles per hour7
Current speed is displayed in mph.
Current fuel consumption
A
B
Continuous information on current fuel
consumption. Fuel consumption is calculated
every second. The figure in the display is
updated every few seconds. When the car is
stationary “----” is displayed.
NOTE! The displayed value may be slightly
off if a fuel-driven heater is used.
C
3601859d
Average fuel consumption
Trip computer
Controls
The trip computer displays the following
information:
In order to access the trip computer information
turn the ring (B) in steps, either forwards or
backwards. By turning again you return to the
starting point.
The average fuel consumption since the last
reset (RESET). When the ignition is switched
off, the average fuel consumption is stored and
remains until reset with the RESET button (C)
on the lever.
NOTE! The displayed value may be slightly
off if a fuel-driven heater is used.
Average speed
Range to empty fuel tank
The average speed since the last reset
(RESET). When the ignition is switched off,
the average speed is stored and used as the basis
of the new value when you continue driving.
This can be reset with the RESET button (C)
on the lever.
Displays the range available with the remaining
fuel, calculated using the average fuel consumption over the last 30 km (18 miles) and the
quantity of fuel remaining. When the range to
empty is less than 20 km (12 miles) “----” is
displayed.
NOTE! The displayed value may be slightly
off if a fuel-driven heater is used.
• AVERAGE SPEED
• SPEED IN MILES PER HOUR7
• CURRENT FUEL CONSUMPTION
• AVERAGE FUEL CONSUMPTION
• RANGE TO EMPTY FUEL TANK
NOTE! If a warning message interrupts while
you are using the trip computer menu, you must
acknowledge the warning message. Then press
the READ button (A) to return to the trip
computer.
7. Certain countries
40
Cruise control (option)
Temporary disengagement
3603564m
Return to a speed
2700412d
Activating
The controls for cruise control are to the left in
the steering wheel.
Setting desired speed:
· Press the CRUISE button. “CRUISE” is
shown on the combined instrument panel.
· Touch + or - to lock the vehicle speed.
CRUISE ON appears on the combined
instrument panel.
Cruise control cannot be engaged at speeds
below 30 km/h or above 200 km/h.
Press 0 to disengage the cruise control
temporarily. CRUISE will be shown on the
combined instrument panel. The speed set
earlier is stored in the memory.
The cruise control is also temporarily disengaged when:
· the brake pedal or clutch pedal is depressed
· speed falls below 30 km/h when travelling
uphill
· the gear selector is moved to position N
· wheel spin or wheel lock-up occurs
· a temporary increase in speed lasts longer
than one minute.
Increasing or decreasing
speed
·
·
·
Increase or decrease the speed by pressing
and holding + or -.
The speed of the car when the button is
released is set as the new speed.
A brief press (less than half a second) on +
A temporary increase in speed (less than
one minute) using the accelerator, such as
while overtaking, does not affect the cruise
control setting. When you release the
accelerator, the car will return to the
programmed speed.
When is pressed, the car resumes the
previously set speed.
“CRUISE ON” is displayed on the combined
instrument panel.
Disengagement
Press CRUISE to disengage the cruise control.
CRUISE ON goes out on the combined
instrument panel.
41
Lighting panel
· Turn the headlamp control (1) to the centre
position. In ignition key position II the
position lamps/parking lamps are always
on. The number plate lighting is switched on
at the same time as the position lamps/
parking lamps.
Headlamps
3501847m
Headlamp levelling
The load in the car changes the vertical
alignment of the headlamp beam, which could
dazzle oncoming motorists. Avoid this by
adjusting the height of the beam.
· Turn the ignition key to position II.
· Turn the headlamp control (1) to one of the
end positions.
· Roll the control up or down (3) to raise or
lower beam alignment.
Cars with Bi-Xenon headlamps (option) have
automatic headlamp levelling, so there is no
control (3).
Position lamps/parking lamps
The position lamps/parking lamps can be
switched on irrespective of ignition key
position.
42
Automatic dipped beam
Dipped beam comes on automatically when
the ignition key is turned to position II, except
when the headlamp control (1) is in the centre
position. If necessary, the automatic dipped
beam can be deactivated by an authorised
Volvo workshop.
Manual dipped beam
If necessary, the automatic dipped beam can be
deactivated by an authorised Volvo workshop.
· Turn the ignition key to position II.
· Turn the headlamp control (1) clockwise to
the end position.
Main beam
· Turn the ignition key to position II.
· Turn the headlamp control (1) clockwise to
the end position.
· Move the left-hand stalk switch towards
the steering wheel to the end position and
release it, see page 43.
Fog lamp
NOTE! Regulations for use of fog lamps vary
from country to country.
Front fog lamps
The front fog lamps (option) can be switched
on along with the headlamps or the position
lamps/parking lamps.
· Press the button (2).
The LED in the button (2) lights when the
front fog lamps are switched on.
Rear fog lamp
The rear fog lamp can only be switched on
with the headlamps or the front fog lamps
(option).
· Press the button (4).
The rear fog lamp indicator symbol in the
combined instrument panel and the LED in the
button (4) come on when the rear fog lamp is
switched on.
Instrument lighting
The instrument lighting is switched on when
the ignition key is in position II and the
headlamp control (1) is in one of the end
positions. The lighting is automatically dimmed
during the day and can be controlled manually
at night.
· Roll the control up or down (5) for brighter
or dimmer lighting.
Left-hand stalk switch, Steering wheel adjustment
The stalk switch remains in its end position
and is moved back manually, or automatically
by steering wheel movement.
2
1
Switching, main and dipped
beam
3
4
1
2
3602430m
Stalk switch positions
1.
2.
3.
4.
Single flash, direction indicators
Continuous flashing, direction indicators
Main beam flash
Switching, main and dipped beam, and home
safe lighting
Direction indicators
Single flash
· Move the stalk switch up or down to
position (1).
When the stalk switch is released it returns to
its start position and the direction indicators
are switched off.
Continuous flashing
· Move the stalk switch up or down to end
position (2).
The ignition key must be in position II for
main beam to be switched on.
· Turn the headlamp control clockwise to the
end position, see page 42.
· Move the stalk switch towards the steering
wheel to the end position (4) and release.
Main beam flash
· Move the stalk switch gently towards the
steering wheel to position (3).
Main beam comes on until the stalk switch is
released.
Home safe lighting
Some of the exterior lighting can be kept
switched on and works as home safe lighting
after the car has been locked. The time delay
is 30 seconds (factory setting), but can be
changed to 60 or 90 seconds by an authorised
Volvo workshop.
· Remove the key from the ignition switch.
· Move the stalk switch towards the steering
wheel to the end position (4) and release.
· Get out of the car and lock the door.
6400296A
Steering wheel adjustment
The steering wheel can be adjusted both
vertically and front-rear.
Push down the control on the left-hand side of
the steering column. Then adjust the steering
wheel to the position that suits you best. Ensure
that the steering wheel fastens in a determined
position (notch). Press the control back into
place to lock the steering wheel.
WARNING!
Adjust the steering wheel before driving,
never while driving. Ensure that the steering
wheel is locked.
43
Right-hand stalk switch
Rain sensor (option)
0
3603483j
Windscreen wipers/washer
0 - The windscreen wipers are off when the
lever is in position 0. If the lever is moved
upward, the wipers swipe one stoke at a time
for as long as the lever is held up.
-Intermittent wiping. The speed of the
intermittent wipe can be adjusted and set. Twist
the ring (see 1 in illustration) upwards to
increase the wiper stroke frequency. Twist the
ring downwards to decrease the wiper stroke
frequency.
- Wipers operate at normal speed
- Wipers operate at high speed
44
The rain sensor automatically increases or
decreases the speed of the windscreen wipers
based on how much water it detects on the
windscreen.
The sensitivity of the rain sensor can be
adjusted using the ring (1).
· Turn the ring upward to increase sensitivity
or down to decrease sensitivity (there is an
extra swipe when the ring is turned upward).
On/Off
When activating the rain sensor, the ignition
key must be in at least position I and the
windscreen wiper lever must be in position 0.
To activate the rain sensor:
· press the button (2). An LED illuminates in
the button to indicate the rain sensor is
active.
To turn the rain sensor off:
· press the button (2) or
· move the lever downward to another wiper
program. If the lever is raised, the rain sensor
will remain active; the wipers make an extra
sweep and then return to rain sensor mode
when the lever is released to position 0.
Important!
In an automatic car wash:
Turn off the rain sensor by pressing the
button (2) while the ignition key is in at
least position I. Otherwise, the windscreen wipers may start and be damaged.
The rain sensor is automatically deactivated
when the key is removed from the ignition
switch or five minutes after the ignition is
switched off.
Windscreen washer
Pull the lever towards the steering wheel to
activate the windscreen washer.
Headlamp washer
(option in certain markets)
Use of the windscreen washer automatically
activates the headlamp washer.
High-pressure wash of the headlamps
consumes a great deal of washer fluid.
To save fluid, the headlamps are only washed
every fifth time (within a ten minute period).
If ten minutes have elapsed since the last
windscreen washing, the headlamps receive a
high-pressure wash the next time the windscreen is washed.
Important!
Use plenty of washer fluid when the wipers
are cleaning the windscreen. The windscreen
must be wet when the windscreen wipers are
operating.
Reduced washing
If only approx. one litre of washer fluid
remains in the reservoir, the supply to the
headlamps is cut off in order to prioritise
cleaning of the windscreen.
Ignition switch and steering wheel lock
Ignition and steering
wheel lock
Ignition keys and electronic
immobilizer
0 Locked position
The steering wheel locks when the
ignition key is removed.
The ignition key must not hang with other keys
or metal objects on the same key ring.
The immobilizer could be inadvertently
triggered, preventing the car from being started.
I Intermediate position “radio position”
Certain electrical components can be
connected. The engine electrical
system is not connected.
II Drive
The key position when driving. The
car’s entire electrical system is
connected. Diesel: Wait until preheating is finished. See page 88.
III Start position
The starter motor is connected. Release the key
when the engine has started. The key springs
back to the driving position automatically.
If the key is difficult to turn the front wheels are
positioned so that there is tension in the steering
wheel lock. Turn the steering wheel back and
forth while turning the key.
Ensuring that the steering wheel is locked when
you leave the car minimises the risk of theft.
WARNING!
Never switch off the ignition (key in the
position 0) or pull out the ignition key
while the car is moving. This can activate
the steering lock, which makes the car
impossible to drive.
45
Hazard warning flashers, rear window defroster, heated front seats
8702787d
8702784d
Front seat heater switch
8702783d
3601944d
Hazard warning flashers
The hazard warning flashers (all direction
indicators flash) should be used when you are
forced to stop or park the car where it is a
hazard or hindrance to traffic.
Please remember: Regulations for using
hazard warning flashers vary from country to
country.
Heated door mirrors
Rear defroster
Use the defroster to remove ice and misting
from the rear window and door mirrors.
Pressing the switch starts heating the rear
window and the door mirrors at the same time.
The LED in the switch lights. A built-in timer
automatically deactivates the door mirror
defroster after about 4 minutes and the rear
window defroster after about 12 minutes.
Heated front seats
If you wish to have extra heat in the front
seat(s) carry out the following:
· Press once: High heat - both LEDs in the
switch light up.
· Press once again: Low heat - one LED in
the switch lights.
· Press once again: heating switched off
(no LEDs are lit).
Your Volvo workshop can adjust the
temperature.
46
Parking brake, Electrical socket/cigarette lighter
68
64
72
76
68
80
64
72
76
80
3601943e
5500045e
Parking brake lever
Parking brake (handbrake)
The lever is located between the front seats. The
parking brake operates on the rear wheels. The
warning symbol in the combined instrument
panel lights when the brake is applied. Pull up
the lever slightly and press in the button to
release the brake.
Remember that the warning symbol in the
combined instrument panel lights even if the
parking brake is only “slightly” applied. Check
that the brake is applied correctly. Pull the
brake hard and make sure it fastens in a
“notch”
Electrical socket at the front seat
3601974d
Electrical socket for the rear seat
Electrical socket/
cigarette lighter
The cover should always be in position if the
socket is not being used as a power source or
as a cigarette lighter socket. The maximum
current is 10A.
47
Power windows
position (AUTO-DOWN - AUTO-UP*), the
power windows open or close automatically.
If you close the front windows using the AUTO
function an integrated clamp protection is
activated if the window is blocked by any
object.
NOTE! The AUTO-UP function on the
passenger side is only available on some
markets.
WARNING!
3601867d
The power windows are operated using the
switches in the door armrests. The ignition key
must be turned to the radio or driving position*
for the power windows to function. The
window opens when you depress the front
section of the switch and closes when you pull
up the front section of the switch.
Windows can be opened or closed from the
front seat two ways.
1. Press the switch gently downwards or pull it
gently upwards. The power windows go up or
down as long as the switch is affected.
2. Press the switch all the way down, or pull it
all the way up, and then release it. In this
48
If there are children in the car:
· Remember to switch off the supply to the
power windows by removing the ignition
key if the driver leaves the car.
· Make sure that children’s and other
passengers’ hands are clear when closing
the windows.
If the rear door windows are operated from
the driver’s door or with the remote control:
· Check that none of the rear seat passen
gers are in danger of getting their hands
caught when closing the windows.
*When you have finished your trip and
removed the ignition key, you can still close or
open the windows as long as you have not
opened either of the front doors.
8301395M
Rear power window switches
The power window switches in the rear seat can
be blocked from the switch on the driver’s door
switch panel. Always remember to break the
current to the power windows (that is to say
remove the ignition key and open one of the
front doors) when you leave children in the car
unattended.
LED in the switch unlit:
The rear door windows can be operated both by
the switch in each door but also by the switch in
the driver’s door.
LED in the switch lit:
The rear windows can only be operated from
the driver’s door.
Rearview mirror
Door mirrors with memory
function (option)
If the car has door mirrors with memory
function, they work together with the memory
setting of the seat, see page 68.
NOTE! The above only applies if your Volvo
is equipped with a driver’s power seat.
A
B
8301236d
8802799r
Switches, power door mirrors
Rearview mirror
Door mirrors
A. Normal position.
B. Dimming position. Use this if headlamps
from the cars behind irritate you.
The switches for setting the two outer door
mirrors are furthest forward on the driver’s
door armrest.
Press the switch. L = left door mirror.
R = right door mirror. LED in the switch lit:
Adjust the postion with the adjustment control.
When you have set the position press the
switch once. The LED should no longer be lit.
Certain models have an autodim function,
which leads to an automatic dimming based on
current light conditions.
Seat belt reminder
The seat belt warning symbol above the
rearview mirror flashes as long as the driver’s
seat belt has not been connected.
Important!
Use the defroster (see page 46) to remove
ice from the mirrors, not an ice scraper. The
scraper could scratch the mirror glass.
Memory function in the remote control
When you unlock the car with the remote
control and change the setting of the door
mirrors, these new settings are saved in the
remote control. The next time you unlock the
car with the same remote control and open the
driver’s door within two minutes, the mirrors
will assume their stored positions.
WARNING!
Adjust the door mirrors before starting off!
The outer half of each door mirror is a wideangle mirror that provides a better overview.
This may make objects appear farther away
than they really are.
49
Power sunroof (option)
3
Manual control
Open: Pull the switch rearwards to the resistance
point position (3). The sunroof will move towards
maximum opening position as long as the switch is
held in this position.
Close: Press the switch forwards to the resistance
point position (2). The sunroof will move towards
its closing position as long as the switch is held in
this position.
4
2
1
5
Pinch protection
6
8302234r
8301747m
Power sunroof (option)
Sunroof controls are located in the headlining.
The sunroof can be opened in two different ways:
· Raise/lower trailing edge(ventilation position)
· Rearwards/forwards (opening position/
comfort position*)
The ignition key must be in position I or II.
Ventilation position
Open: Push the trailing edge of the switch (5)
upwards.
Close: Pull the trailing edge of the switch (6)
downwards.
It is possible to switch directly from the ventilation position to comfort position*: pull the
control backwards to its end position (4) and release.
* In comfort position, the sunroof is not completely open in order to reduce the level wind noise.
50
1. Automatic closing
2. Manual closing
3. Manual opening
4. Automatic opening
5. Opening ventilation position
6. Closing ventilation position
Opening position/comfort position*
Automatic control
Move the control over the resistance point
position (3) to the rearmost end position (4) or
over the resistance point position (2) to the front
end position (1) and release. The sunroof will
open to the comfort position* or will close
completely.
Open from comfort position* to max. opening:
pull the control to the rear once more to the end
position (4) and release.
NOTE! The sunroof pinch protection function
is activated if the hatch is blocked by an object.
If blocked, the sunroof will stop and automatically open to the previous open position. This
function will be activated only when the
sunroof is in the open position.
WARNING!
Pinch protection functions only in the
opening position - not in ventilation position.
Make sure the sunroof is properly closed
before leaving the car.
WARNING!
· Make sure that the hands of children and
passengers are clear when closing the
sunroof.
If there are children in the car:
· Remember to switch off the supply to the
sunroof (remove the ignition key) if the
driver leaves the car.
Sun screen, Sun blinds (option)
A
8301256d
Sun screen
Sun blind - rear window
The sunroof also has an inner manually sliding
sun screen. The sun screen slides back
automatically when the sunroof is opened.
Pull the sun blind up from the parcel shelf and
hook it into the holes above the rear window, as
illustrated.
Sun blinds - rear side
windows
Lower the window slightly. Hook the sun blind
(A) onto the top edge of the window. You can
now raise and lower the window as you wish.
51
Laminated side windows (option), Water-repellent coating (option)
Laminated side windows
(option)
The laminated windows in the front and rear
doors improve sound insulation in the passenger compartment and provide better protection
against unauthorised entry.
Water and dirt-repellent
coating on the front windows
and/or door mirrors (option)
The front windows and/or door mirrors are
treated with a coating that ensures that visibility
through the windows or in the mirrors is good
even if it is raining. For information on glass
care, see page 142.
Side windows and mirrors
treated with the water and/or
dirt-repellent coating are
marked with a little symbol.
Rearview mirror/door mirrors
In certain weather conditions, the function of
the dirt-repellent coating is improved if the door
mirror defroster is used, see page 46.
Defrost the door mirrors:
· if they are covered with ice or snow
· in heavy rain and dirty road conditions
· if they are misted.
Important!
· Do not use a metal ice scraper to remove
ice from the windows. The water and
dirt-repellent coating could be damaged.
· Use the defroster to remove ice from the
mirrors.
52
Climate control
Air distribution
54
Your climate control system - useful hints
55
Electronic Climate Control ECC
56
Electronic Climate Control ECC with Interior Air Quality system
57
Electronic Climate Control ECC - manual settings
59
Manual climate control with air conditioning (AC)
60
Fuel-driven parking heater (option)
62
53
Air distribution
D
A
C
D
C
C
A
B
D
8702818d
8702826d
Air vents in the dashboard
8702835d
B
Air vents in the door pillars
Air vents in the dashboard
Air distribution
Air vents in the door pillars
A
B
C
D
The incoming air is distributed through 14
different air vents located in different parts of
your car.
A
B
C
D
Open
Closed
Directing airflow laterally
Directing airflow vertically
· Aim the outer vents towards the side
windows to remove misting.
· In cold climates: close the centre vents
for the most comfortable climate and best
demisting.
54
Open
Closed
Directing airflow laterally
Directing airflow vertically
· Aim the vents toward the rear side windows
to remove misting.
· Aim the vents inwards into the car if you
wish to have a comfortable climate in the
rear seat.
· Bear in mind that small children are
sensitive to airflow and draughts.
Your climate control system - useful hints
Misting on window interiors
Side windows and sunroof
A good way to reduce the problem of misting
on the insides of the windscreen and other
windows is to clean them. Use a normal
window cleaner. Bear in mind that you must
clean them more often if someone smokes in
the car.
For the air conditioning (A/C) system to operate
satisfactorily the side windows and sun roof
should be closed. Also, remember not to block
the evacuation channels in the parcel shelf.
Ice and snow
The air conditioning system switches off
temporarily at full acceleration. You may feel
a temporary rise in temperature.
Remove ice and snow from the climate control
air intake (the grille between the bonnet and the
windscreen).
Particle filter
Make sure the particle filter is replaced
regularly. Consult your Volvo workshop.
Acceleration
Condensation
In warm weather conditions condensation from
the air conditioning (A/C) system may drip
under the car. This is completely normal.
Fuel economy - Electronic
Climate Control (ECC)
With ECC, the air conditioning system is
controlled automatically and is used just
enough to cool the passenger compartment and
dehumidify the incoming air.
This provides better fuel economy compared to
conventional systems where the air conditioning cools the air to just above freezing point.
Ventilation fan function
When the engine is off (and if the ignition key
is in position I or II), the ventilation fan is
automatically switched off. This is to prevent
the battery from becoming discharged.
To activate the ventilation fan, turn the fan
control and set the desired speed.
Fault tracing
Actual temperature - ECC
The temperature you select corresponds to the
physical experience with reference to air speed,
humidity, exposure to sun, etc. which affect the
interior and exterior of the car.
Sensors - ECC
The sun sensor is on the upper portion of the
dashboard. Remember not to cover it. Do not
cover the passenger compartment temperature
sensor on the climate control panel.
Your Volvo workshop has the instruments and
tools required for any fault tracing or repair of
your climate control system. Entrust checks and
repairs only to trained personnel.
Refrigerant
Refrigerant R134a is in the air conditioning
system. This contains no chlorine, which means
it is harmless to the ozone layer.
Use only R134a when topping up/refilling
refrigerant. This work should be performed by
an accredited workshop.
55
Electronic Climate Control ECC
Recirculation/Interior Air Quality System
MAN
AUT
AUTO
Recirculation
20
18
22
Defroster, windscreen and
side windows
Passenger compartment
Defroster, rear window
temperature sensor
and door mirrors
24
26
20
18
22
Seat heater,
right-hand side
24
26
AC On/Off
Seat heater left
hand side
Fan
8704253d
Temperature,
left hand side
Temperature
right-hand side
Air distribution
56
Electronic Climate Control ECC with Interior Air Quality system (option)
Multifilter with
Air quality sensor (option)
Some cars are equipped with a multifilter and
air quality sensor. The multifilter separates
gases and particles, thus reducing the volume of
odours and contaminants entering the car. The
air quality sensor detects increased levels of
contaminants in the outside air. When the air
quality sensor detects contaminated outside air,
the air intake is closed and the air inside the
compartment is recirculated. The multifilter also
cleans the air recirculating in the compartment.
Keep in mind the following:
AUT
MAN
8703250d
Operation:
Press
to activate the air quality sensor
(normal setting).
8702780d
When the air quality sensor is connected, the
Or select one of three functions by
green AUT LED lights in
MAN
AUT
8703250d
· Make it a rule to have the air quality sensor
activated at all times.
· Recirculation is limited in cold climates to
avoid misting.
· In the event of misting, you should
disconnect the air quality sensor.
· In the event of the windows misting up you
can use the windscreen and side window
defroster functions. See next page.
· Follow the Volvo service programme for
the recommended interval for multifilter
replacement.The Multifilter may need to be
changed more often if you drive in heavily
polluted environments.
.
pressing
MAN
.
AUT
8703250d
1. Press
MAN
AUT
: the LED AUT lights. The air
8703250d
quality sensor is now activated.
2. Press
MAN
AUT
: no LED lights. Recirculation
8703250d
is not activated unless needed to cool.
3. Press
MAN
AUT
: the LED MAN lights.
8703250d
Recirculation is now activated.
You can switch between these three functions
by repeatedly pressing
MAN
AUT
.
8703250d
57
Electronic Climate Control ECC
AUTO
The AUTO function regulates climate control so
that the selected temperature is attained. The
automatic function controls heating, air condition8702780d
ing, fan speed, recirculation and air distribution. If
you select one or more functions manually, the
other functions continue operating automatically.
All manual settings are switched off when AUTO is switched on.
20
18
22
Temperature
24
26
8702779d
The two knobs can be used to set the temperature for
the passenger and driver’s sides of the car. Remember
that it will not heat or cool any quicker even if you
select a higher or lower temperature than you wish to
have in the passenger compartment.
Defroster windscreen and side windows
Use this button to quickly remove misting and ice
from the windscreen and side windows. The air
8702782d
flows to the windows at high fan speed. The LED
in the defroster button lights when this function is
activated. The air conditioning system is now controlled so that the air is
maximally dehumidified. The air is not recirculated.
58
Defroster rear window and door mirrors
8702783d
Use this button to quickly remove ice and misting
from the rear window and door mirrors. See
page 46 for more information about this function.
Electronic Climate Control ECC - manual settings
AC - On/Off
Recirculation
(see also page 60)
MAN
AUT
The best cooling in warm
climates is achieved by
selecting the AUTO function.
The recirculation is then controlled automatically. Manual recirculation can
be selected if you wish to shut out bad air, exhaust fumes etc. The air in
the passenger compartment is recirculated; no air from outside the car is
is activated. The LED in the switch is lit.
taken into the car when
If you allow the air in the car to recirculate there is a danger of misting
and icing in the car, especially during the winter.
The timer function (cars with multifilters and air quality sensors
have no timer function) minimises the risk of ice, misting and bad air.
for more than
Carry out the following to activate it. Press
3 seconds. The LED flashes for 5 seconds. The air in the car recirculates
for 3-12 minutes depending on the outer temperature. Each time you press
the timer function is activated. If you wish to switch off the timer
function, press
again for more than 3 seconds. The LED lights for
5 seconds to confirm your selection.
8702776d
If you select Defroster
8703250d
, recirculation is always disconnected.
Air distribution
When the ON LED lights the air conditioning
(A/C) system is controlled automatically by the
system. In this way incoming air is cooled and
8702777d
moderately dehumidified. When AC OFF is
selected and the OFF LED lights the air conditioning (A/C) system is always disconnected, other functions are still
controlled automatically. The air conditioning (A/C) system operates down
to approximately 0 °C.
the air conditioning system is controlled
When you select Defroster
so that air is maximally dehumidified.
Fan
8702778d
Fan speed can be increased or decreased by
turning the knob. If AUTO is selected, fan speed is
controlled automatically. The previously set fan
speed is disconnected.
NOTE! If the knob for the fan has been turned so far that the left
LED above the knob lights up with an orange light, the fan and the
air conditioning (A/C) system are switched off.
Air to windows.
Air to head and body.
Heating the front seats
Air to legs and feet.
See page 46 for more information.
8702781d
Press AUTO to return to automatic air distribution.
8702784d
59
Manual climate control with air conditioning (AC)
Recirculation
Recirculation, together with your air conditioning
(A/C) control, helps to cool a warm cabin more
quickly. This function can also be used to exclude
8702776d
bad air, exhaust fumes etc. The air in the passenger
compartment is recirculated; no air from outside the car is taken into the
is activated. The LED in the switch is lit. If you
car when the button
allow the air in the car to recirculate there is a danger of misting and icing
in the car, especially during the winter.
The timer function minimises the risk of ice, misting and bad air. To
activate the function: press
for more than 3 seconds. The LED flashes
for 5 seconds. The air in the car recirculates for 3-12 minutes depending
the timer function is
on the outer temperature. Every time you press
activated. If you wish to switch off the timer function, press
again for
more than 3 seconds. The LED lights for 5 seconds to confirm your
selection.
Recirculation is always disconnected when you select Defroster
.
AC - On/Off
(ON/OFF)
The air conditioning is
connected to the cooling and
dehumidification function
when the ON LED lights. The air conditioning is
disconnected with the OFF LED lights.
8702777d
When you select Defroster
, the air conditioning is always connected, unless the fan is set at
position 0.
8702611d
Fan
8702831d
60
Fan speed can be increased
or decreased by turning the
knob. If the knob is set to 0,
the air conditioning is
disconnected.
Heating/Cooling left side
8702834d
Turn to adjust the heating or
coooling of the incoming air.
The air conditioning must
be connected to receive
cooled air.
Heating/Cooling right side
8702834d
Turn to adjust the heating or
coooling of the incoming air.
The air conditioning must
be connected to receive
cooled air.
Manual climate control with air conditioning (AC)
Use the air distribution control positions (marked with dots) between the
different symbols to fine-tune air distribution for maximum comfort.
8702833d
Air distribution
Air through front and rear air vents.
Use…
Here is some supplementary
advice and information:
· You must turn the fan knob (from the
0 position) to connect the air conditioning.
· Use the air conditioning at low temperatures
(0 - 15 °C) to dehumidify incoming air.
When you want good cooling in a
warm climate.
Air to windows In this position the
air does not recirculate. The air
conditioning (A/C) system is always
connected. There is a certain amount
of airflow to the vents.
When you want to remove ice and misting.
High fan speed is good for this.
Air to both floor and windows.
There is a certain amount of
airflow to the air vents.
When you want comfortable conditions
and good demisting in a cold climate. Not
too low a fan speed.
Air to floor. There is a certain
amount of airflow to the air vents
and the defroster vents for the
windscreen and side windows.
When you want to warm your feet.
Defroster - rear
window and
door mirrors
Use this button to quickly
remove ice and misting
from the rear window and door mirrors. See
page 46 for more information about this
function.
8702787d
Heating the
front seats
See page 46 for more
information.
Air to floor and air vents.
In sunny weather with cool outside
temperature.
8702784d
61
Fuel-driven parking heater (option)
At temperatures of -10 °C and below, the
parking heater runs a maximum of 60 minutes.
If the parking heater does not start despite repeated attempts, a message is shown on the
display. Contact an authorised Volvo workshop.
A
B
C
3602296d
General
The electrical system must be ”awakened” before the parking heater can be programmed.
This is most easily done by:
· pressing the READ button or
· pressing the main beam flash or
· turning on the ignition.
The parking heater can be started immediately
or set with two different start times using
TIMER 1 and TIMER 2.
Here, start time refers to the time point the car
should be completely warmed up.
Vehicle electronics calculates start time based
on current outside temperature. If the outside
temperature exceeds 25 °C, heating is not
switched on.
62
WARNING!
• Switch off the fuel-driven heater before
refuelling. Spilled fuel could be ignited by
the exhaust gases.
• Check the information display to ensure
the heater is off (PARK HEAT ON is
shown on the display when the parking
heater is active).
WARNING!
The car must be outdoors when the petrol
or diesel heater is used.
WARNING!
ACHTUNG!
AVERTISSEMENT!
8903920d
Warning decal on fuel filler flap
Messages on the display
Once the settings for TIMER 1, TIMER 2
and DIRECT START are activated, the amber warning symbol in the combined instrument panel lights and explanatory text is
shown on the display.
When you leave the car, you will receive a
message regarding the current settings of the
system.
Parking on a hill
If you park your car on a steep incline, the
front of the car should be facing up the slope
to ensure the supply of fuel to the parking
heater.
Car clock/timer
For safety reasons, all timer settings will be
cleared if the car clock is reset after timer
settings have been made.
Fuel-driven parking heater (option)
A
B
C
3602296d
After setting TIMER 1, toggle to TIMER 2.
Settings are made the same way as for TIMER 1.
Deactivating timer-started heating
Do as follows to manually switch off the heater
before the set time has elapsed:
1. Press the READ button (A).
2. Use the ring (B) to toggle to PARK HEAT
TIMER 1 (or 2). The text ON flashes.
3. Press the RESET button (C). The text OFF
is displayed with a steady glow and the
heater is switched off.
Direct start of heater
Setting TIMER 1 and 2
For reasons of safety, you can only programme
times for the following 24 hours, not several
days in a row.
1. Use the ring (B) to toggle to TIMER 1.
2. Briefly press the RESET button (C) so
that the hours setting starts to flash.
3. Use the thumb wheel to set the desired
number of hours.
4. Briefly press the RESET button so that the
minutes setting starts to flash.
5. Use the ring (B) to set the desired minutes.
6. Briefly press the RESET button to confirm
your setting.
7. Press the RESET button to activate the
timer.
1. Use the ring (B) to toggle to DIRECT
START.
2. Press the RESET button (C) to make ON
and OFF selections available. Select ON.
The heater will now run for 60 minutes.
Heating of the passenger compartment will
begin as soon as the engine coolant has reached
an adequate temperature.
Deactivation of heater after direct start
1. Use the ring (B) to toggle to DIRECT
START.
2. Press the RESET button (C) to make ON
and OFF selections available. Select OFF.
Battery and fuel
If the battery is not sufficiently charged or the
petrol tank is close to empty, the parking heater
will be switched off.
If this is the case, a message will appear on the
display. Confirm the message using the READ
button (A).
.
Important!
Repeated use of the parking heater combined
with only short journeys can discharge the
battery and impair starting.
In order to ensure that the generator receives
sufficient time to produce the amount of
energy needed without discharging the battery
as a result of regular heater use, drive the car
for a period equalling the time during which
the heater has been active.
Auxiliary heater (diesel)
(certain countries)
Extra heat from the additional heater may be
required in cold weather to reach the correct
temperature in the passenger compartment.
The additional heater starts automatically
when extra heat is required if the engine is running. It is switched off automatically when the
correct temperature is reached or when the
engine is switched off.
63
64
Interior
Front seats
66
Interior lighting
69
Storage compartments
70
Centre console storage compartments, Load curtain
71
Spare wheel, Warning triangle
72
Coat hanger, Cup holders in armrest
73
Long loads
74
65
Front seats
The driver’s and passenger seats can be
adjusted to the optimum sitting and driving
positions.
1. Forward/rearward: Lift the handle to
adjust the distance to the steering wheel
and pedals. Check that the seat is locked
after changing position.
2. Raise/lower front edge of seat cushion:
pump up/down.*
3. Raise/lower seat: pump up/down.
4. Adjust lumbar support: turn the wheel.
5. Adjust backrest rake: turn the wheel.
6. Power seat control panel.
* The control panel (2) is not available with
certain upholstery alternatives.
8504932m
WARNING!
•
•
66
Adjust the position of driver’s seat
before setting off, never while driving.
Check that the seat is locked in position.
Folding the front passenger seat, Rear seat head restraints
8502027e
8501727A
Adjust the head restraint vertically
Folding the front passenger seat
Rear seat head restraints
The front passenger seat backrest can be folded to a horizontal position
to make room for a long load. Fold the backrest as follows:
The centre seating position head restraint is
adjusted vertically according to the height of
the passenger. Press the head restraint up or
down as necessary. To move the head restraint
up or down, you must press the release button
behind the left-hand support. See illustration.
If the integrated booster cushion is used, the
head restraint must be carefully positioned to
suit the child.
·
·
·
·
·
Move the seat as far back as possible.
Adjust the backrest to the upright position.
Lift the catches on the rear of the backrest.
Fold the backrest forward.
Slide the seat forward so that the head restraint is “locked in place”
under the glovebox.
67
Front seats
Memory function in the remote control
(option)
If the setting of the seat is changed, the new
setting is saved in the remote control used to
lock the car. The next time the car is unlocked
using that remote control and the driver’s door
is opened within five minutes, the driver’s seats
and door mirrors assume the stored positions.
M
E
M
3
8505020m
Seat adjustment
The switches can be used to make the following
adjustments:
1. Front edge of seat cushion up/down
2. Seat forward/rearward
3. Seat up/down
4. Backrest rake
The seat can be moved in one direction at a
time.
The power seats have an overload protector
that activates if a seat is blocked by an object.
If this occurs, switch off the ignition (position 0) and wait 20 seconds before operating
the seat again.
WARNING!
• Ensure that there is nothing in front
of, behind or under the seat during
adjustment.
• Make sure that none of the backseat
passengers will be trapped.
• Make sure that children do not play
with the switches, to avoid the risk of
getting trapped.
68
2
Preparations
The seat is usually adjusted with the ignition
key is in position I or II. It can also be adjusted
within 4.5 minutes of unlocking the door with
the key or remote control. If the door is closed
but the ignition key has not yet been inserted in
the ignition switch or is in position 0 in the
ignition switch, settings can be made within 40
seconds of closing the door.
1
Power seat (option)
Seat with memory function
(option)
5. Setting seat and door mirrors, program 1
6. Setting seat and door mirrors, program 2
7. Setting seat and door mirrors, program 3
8. Storing preset positions
Three positions can be stored. After adjusting
the seat, hold the MEM (8) button depressed
while pressing the button (5). Further seat and
door mirror settings can be stored using
memory buttons (6) and (7).
Setting preset positions
Press and hold one of the memory buttons (5),
(6) or (7) until the seat stops. If you release
the button, the seat stops immediately for
safety reasons.
Emergency stop
If the seat accidentally begins to move, press
one of the buttons to stop the seat.
Interior lighting
3500887e
3501410r
General lighting and front reading lamps
General lighting
General lighting lights up and goes out when you
press the button. General lighting comes on
automatically* and remains lit for 30 seconds:
· When you unlock the car from the outside
using the key or remote control.
· When you have stopped the engine and
turned the ignition key to position 0.
General lighting lights up and remains lit for
10 minutes:
· When one of the doors is open.
* The function is light-dependent and is only
activated when it is dark.
Rear reading lamps
General lighting goes out:
· When the engine is started.
· When you lock the car from the outside
using the key or remote control.
General lighting can be switched off or on in all
situations by briefly pressing the button.
When you switch the light on, it remains lit for
10 minutes.
You can disconnect the automatic function by
pressing the button for more than 3 seconds.
When you then briefly press the button, the
automatic function reconnects.
The pre-programmed times of 30 seconds and
10 minutes can be changed. Contact an
authorised Volvo workshop.
8504139m
Vanity mirror in the sun visor
Front and rear reading lamps
Reading lamps in the front and rear seats can
be switched on or off by pressing the respective
button. Reading lamps are switched off
automatically after 10 minutes if not switched
off manually.
Vanity mirror
The lamps come on when you open the cover.
69
Storage compartments
8505249e
WARNING!
Make sure that no hard, sharp or heavy objects lie on or in
(or protrude from) the parcel shelf, map pocket or other
storage compartments where they might cause injury during
heavy braking. Always fasten large heavy objects with one of
the seat belts.
70
Centre console storage compartments, Load curtain
8501983E
Cup holder
(option)
8502003d
Ashtray (option)
To empty the ashtrays:
Front seat: pull the ashtray straight upwards.
Rear seat: press the ashtray downwards and
remove.
Some models are
equipped with cup
holders for the front and rear seat occupants.
To open the cup holders in the front seats,
press the left-hand button in the centre console
to open the driver’s cup holder and the cover
below to open the passenger-side cup holder.
To close the passenger-side holder after use,
the arms must be pressed inwards as indicated
by the arrows on the holder. You can also use
the storage compartment in the centre console
for cassette tapes and the like.
Retaining strap in cargo
compartment (option)
The retaining strap can be used to secure lighter
objects, such as grocery bags or hand luggage.
Pull it out. It works like a seat belt and has a
locking function.
Pull the release tab to release the retaining strap
from its locked position and pull it out further.
The retaining strap can be fixed in two
positions. When securing the strap in position,
press until there is an audible click.
NOTE! If you have an extra plastic mat with
edges that go up along the sides of the cargo
compartment, you must cut a groove in the mat
so that the retaining strap can run freely.
71
Spare wheel, Warning triangle
Floor support
Jack
Warning triangle
Tool kit with
towing eye
Jack
A
Mounting
Spare wheel
Floor support
7700231d
8901312d
Spare wheel, tools, jack
Warning triangle (certain countries)
The spare wheel with the jack and tool kit can be found under the floor
of the cargo compartment. Carry out the following to remove the spare
wheel:
· Fold the floor inwards.
· Lift and remove the floor support that sits in the spare wheel mounting. Cars with a “Temporary Spare” also have a floor support in the
rear left-hand corner of the cargo compartment. Pull the support
upwards to facilitate removing the spare wheel.
· Lift out the jack and tool kit.
· Unscrew the mounting and lift out the spare wheel.
· Return and secure everything in the reverse order. Make sure that the
spare wheel is fixed in place and that the jack and tool kit are
properly secured with the straps on the mounting.
Follow the regulations concerning warning triangles of the country you are
in. Carry out the following when the warning triangle is required for use:
· Turn both attachment screws to the vertical position.
· Carefully remove the warning triangle case.
· Remove the warning triangle from its case (A).
· Fold out the four support legs on the warning triangle.
· Fold out and secure the two remaining sides of the warning triangle.
· Place the warning triangle in a suitable position. Think about the
position of the car and the traffic.
After use:
· Pack everything in reverse order.
· Make sure the warning triangle and its case are properly secured in
the boot lid.
72
Coat hanger, Cup holders in armrest
8503126m
8504929m
Coat hanger
The coat hanger is only intended for light
garments.
Cup holders in the rear seat
armrest
73
Long loads
8501909d
8501931e
8502002d
Always secure long loads!
Tipping the backrests forward
One or both of the rear seat backrests can be
folded down from the cargo compartment for
transporting long objects. Pull the handle(s) in
the cargo compartment. The head restraints
must be in the upright position. Then tip the
backrest or backrests forward. The centre head
restraint may need to be adjusted.
When raising the backrests, ensure that they
are properly secured and locked.
74
Hatch for long objects
A hatch in the right-hand rear backrest allows
you to transport long objects such as skis and
planks.
Open the hatch as follows:
- Fold the left-hand backrest and centre
armrest forwards.
- Release the hatch by pushing the catch
upward while folding the hatch forward.
- Tip the backrest back into position with
the hatch open.
Use the seatbelt to secure the load.
WARNING!
Always secure the load. During heavy
braking the load may otherwise shift,
causing personal injury. Cover sharp edges
with something soft. Turn off the engine
and apply the parking brake when loading
or unloading long objects! You may
accidentally knock the gear lever or gear
selector with the load and cause a gear to
engage and the car to move off.
Long loads
NOTE! If your Volvo is equipped with an
integrated booster cushion, you must fold
this out first.
The cover on the rear seat armrest/child seat
has no hinge. The cover must be removed
before the ski hatch is used.
When removing:
- Open the cover 30°
- pull straight up.
When fitting:
- move the cover back in the grooves behind
the upholstery
- close the cover
75
76
Locks and Alarm
Immobilizer, remote control
78
Locking and unlocking
79
Replacing the battery
80
When it is dark, deadlocks
81
Child safety lock, Service locking
82
Alarm
83
77
Doors and locks
Keys - Immobilizer
Your car is delivered with two master keys and
one service key*. One of the master keys is
foldable and equipped with an integrated remote
control.
Loss of key
If you should lose one of your keys, bring the
remaining keys to an authorised Volvo
workshop. As a crime prevention measure, the
code for the lost key is erased from the system
and the other keys must be re-coded in the
system.
The key blades’ unique code is available at
authorised Volvo workshops, which can
produce new key blades.
A maximum of six remote controls/key blades
can be programmed and used for one single car.
Master key
This key operates all locks
Service key*
For driver's door, ignition switch and
steering wheel lock only.
8302498d
*: certain markets only
78
1
6
2
5
4
3
8302187m
1. Unlock 2. Open boot lid
3. Alarm function 4. Approach lighting
5. Lock 6. Fold/open key
Immobilizer
Each key has an integrated coded chip. The code
must be the same as the code in the ignition
switch receiver. The car can only be started if
the correct key with the correct code is used.
Remote control functions
Ignition keys and electronic immobilizer
The ignition key must not hang with other keys
or metal objects on the same key ring. The
immobilizer could be inadvertently triggered,
preventing the car from being started.
2. Boot lid
Press button (2) twice to unlock the boot lid
only.
1. Unlocking
Press button (1) to unlock all doors, the boot lid
and the fuel filler flap.
3. Alarm function
The alarm function can be used to attract
attention during emergency situations. If the red
button (3) is held for at least 3 seconds or is
Locking and unlocking
pressed twice in succession during the same
amount of time, the direction indicators and horn
will be activated. The alarm is deactivated
automatically after 25 seconds or by pressing
any of the buttons on the remote control.
4. Approach lighting
Do the following when you approach the car:
Press the yellow button (4) on the remote
control.
The interior lighting, parking lamps, numberplate lighting and the lamps in the door mirrors
(option) will switch on. If a trailer is attached to
the car, the trailer lights will also be switched
on. These lights will remain lit for 30, 60 or
90 seconds. An appropriate time setting for
your car can be performed at an authorised
Volvo workshop.
In order to switch off Approach lighting:
press the yellow button again.
5. Locking
Lock all doors, boot lid and fuel filler flap with
button 5. There is a delay of approx. 10 minutes
for the fuel filler flap.
6. Folding/opening key
The key can be folded by pressing button 6
while folding the key blade into the keypad.
The folding key will open automatically with
one press of the button.
8302186m
8301290d
Locking and unlocking the
car from the outside
Locking and unlocking the
car from the inside
Using the master key or its remote control, all
the doors and the boot lid can be locked or
unlocked from the outside at the same time.
When the vehicle is locked, the door locking
buttons and interior door handles are
disconnected.
Using the master key or its remote control, all
the doors and the boot lid can be unlocked from
the outside at the same time.
All doors and the boot lid can be locked and
unlocked at the same time using the switches in
the door panel (applies if the vehicle is opened
with the master key).
Additionally, each door can be locked with the
lock button and unlocked by opening the door
using the handle.
The above situation is valid, as long as you
haven’t locked the car from the outside!
If the car is locked from the outside, the fuel
filler flap locks after a 10-minute delay.
79
Locking and unlocking, Replacing battery
Automatic relocking
If none of the doors or the boot lid is opened
within two minutes of being unlocked with the
remote control from the outside, all locks
will be automatically relocked. This function
prevents you from inadvertently leaving the car
unlocked.
For cars with an alarm, see page 83.
NOTE! If the boot lid was opened with the
button on the remote control, it will not
automatically relock.
8302194m
Automatic locking
The doors lock automatically when vehicle
speed exceeds 7 km/h and remain locked until a
door is opened from the inside or are unlocked
using a central locking button.
Unlocking/locking the boot lid
with the remote control
Do as follows to unlock the boot lid only:
· Press the remote control button for the boot
lid two times. The boot lid is unlocked and
opens slightly.
If all doors are locked when you close the boot
lid, it locks automatically.
80
Unlocking the boot lid with
the master key
Normally the boot lid is locked or unlocked
when you lock or unlock the car using the
master key in the driver’s door or the remote
control. The boot lid can be opened by slowly
pressing the button on the remote control twice
within three seconds, or by pressing the boot
lid opener. The master key should only be used
to unlock the boot lid in emergency situations
(if the remote control is broken or if the car is
without power). In such cases: insert the master
key into the upper or lower part of the plug
covering the lock. Twist the key upwards or
downwards and remove the plug. Then unlock
the boot lid.
8302195m
Replacing the battery
If the locks repeatedly fail to react to signals
from the remote control at a normal distance, the
battery should be replaced at the next service
interval or within the course of a couple of
weeks.
· Remove the cover by carefully prising up
the rear edge with a small screwdriver.
· Change the battery (type CR 2032, 3 volt),
the plus side should be up. Avoid touching
the battery and its contact surfaces with your
fingers.
· Refit the cover. Make sure the rubber seal is
properly fitted and free from damage to
prevent water form entering.
· Turn the old battery in to your Volvo
workshop so that it is disposed of in an
environmentally friendly way.
When it is dark, deadlocks
When it is dark
Deadlocks*
Approach lighting
Carry out the following when you approach
the car:
· Press the yellow button on the remote
control.
The interior lighting, parking lamps, numberplate lighting and lamps in the door mirrors
now light (certain models).
Your car has a special deadlock position which
means that the doors cannot be opened from the
inside if they are locked. Deadlocks can only be
activated from the outside by the driver’s door
being locked with the key or remote control. All
doors must be closed before deadlocks can be
activated.
The doors then cannot be opened from the
inside. The car can only be unlocked from the
outside via the driver’s door or by using the
remote control (this only applies to cars that are
equipped with deadlocks). The car cannot be
opened by manipulating the door buttons from
the outside.
Deadlocks are engaged after a 25 second delay
once the doors have been closed.
WARNING!
Do not allow anyone to remain in the car
without deactivating the deadlock
3602415d
Deactivating deadlocks
If someone wishes to remain in the car but you
still wish to lock the doors from the outside the
deadlocks can be disconnected. From the time
the key is turned from position II until you lock
the car, or as long as the centre console is
supplied with current, you can press the button.
The LED in the button then comes on and stays
on until you lock the car using the key or
remote control. A message is displayed as long
as the key remains in the ignition switch. The
deadlock is now disconnected. The deadlocks
will be re-activated the next time the ignition is
switched on.
* Certain countries
81
Child safety lock, Service locking
83
8302518d
Control for child safety lock - left-hand rear
door.
Mechanical child safety locks rear doors
The controls for the child safety locks are in
the rear edge of each rear door and are only
accessible when the door is open. Use a flat
metal object, such as a screwdriver, to turn the
control and thus activate or deactivate the child
safety lock.
A. Child-safe position - the doors cannot be
opened from inside; turn outwards.
B. Not child-safe position - the doors can be
opened from inside; turn inwards.
Child safety lock controls - right-hand rear
door.
WARNING!
Remember that in the event of an
accident, rear seat passengers cannot
open the rear doors from the inside if the
child safety locks are activated.
Therefore, keep the doors unlocked
while driving! In the event of an
accident, rescue personnel will then be
able to enter the car from the outside
Service locking*, boot lid
This function is beneficial if the car is left for
service, with a hotel parking valet or the like.
The service key is left with the staff, who can
open and drive the car but do not have access to
the boot lid (or the glovebox if it is locked with
the master key).
To activate service locking:
· Turn the master key to position II.
· Press the button. An LED in the button
lights when the function is activated and a
message is shown on the display.
To deactivate service locking:
· Turn the master key to position II and
press the button again.
* Certain countries
82
Alarm
The alarm system (option)
Deactivating a triggered alarm
When the alarm is connected, it continually monitors all alarm points. The
alarm is triggered if:
· the bonnet is opened.
· the boot lid is opened.
· a side door is opened.
· the ignition switch is turned with a non-approved key or subjected to
force.
· a movement is detected in the passenger compartment (if a movement
detector is installed - extra equipment).
· the car is lifted or towed away (if it is equipped with a tilt detector extra equipment).
· the battery cable is disconnected.
· anyone tries to disconnect the siren.
Press the UNLOCK button on the remote control if the alarm sounds and
you wish to deactivate it. Two short flashes of the direction indicators are
given as confirmation.
Activating the alarm
Press the LOCK button on the remote control. A long flash signal from
the car’s direction indicators confirms that the alarm is active and that all
doors are closed. In certain markets the key or the switch in the driver’s
door can be used to alarm the car.
Alarm signals
The audio signal is given from a siren with a reserve battery. Each alarm
signal lasts 25 seconds.
If the alarm is triggered, all direction indicators flash for 5 minutes or until
you deactivate the alarm as described above.
Automatic alarm reset
If neither the side doors or rear door are opened within two minutes of
the alarm being disarmed, and the car is unlocked with the remote
control, the car automatically rearms the alarm. The car is simultaneously
locked. This function prevents you from accidentally leaving the car
unalarmed.
Automatic arming of the alarm
In certain countries (Belgium, Israel etc.) the alarm is automatically armed
after a slight delay if the driver’s door is opened and closed but the car is
not locked.
Deactivating the alarm
Press the UNLOCK button on the remote control. Two short flash
signals from the direction indicators of the car confirm that the alarm is
deactivated. In certain markets, the key can be used to deactivate the
alarm.
83
Alarm
Status indicator lamp on the dashboard
An indicator lamp (LED) at the top of the dashboard gives a description of
the alarm system status:
· Lamp not lit: Alarm is deactivated.
· Lamp flashes once every 2 seconds: alarm is armed.
· Lamp flashes quickly, after deactivating the alarm and until the ignition
is switched on: The alarm has been triggered.
· If a fault has occurred in the alarm system, a message is shown in
the display with instructions for appropriate measures.
3602415d
IMPORTANT!
Do not attempt to repair or modify alarm system components. All such
attempts can affect terms of insurance.
Temporary deactivation of detectors
To avoid triggering the alarm inadvertently, for example when leaving
a dog in the car or during a ferry crossing, the movement and tilt detectors
can be temporarily deactivated. The button can be pressed at any time
between the key being turned from position II to the car being locked, or
as long as the power to the centre console is on. The LED in the button
lights until you lock the car with your key or remote control.
A message is displayed as long as the key remains in the ignition lock.
The detectors will be reactivated the next time you switch on the ignition.
If your car is equipped with deadlocks, these will be simultaneously
activated. See page 81.
84
Alarm
Testing the alarm system
Testing the movement detector for the passenger compartment:
1. Open all windows.
2. Activate the alarm. Alarm activation is confirmed by the LED flashing
slowly.
3. Wait 30 seconds.
4. Test the movement detector in the passenger compartment by lifting a
bag or similar from the seat. The alarm should now sound and flash.
5. Deactivate the alarm by unlocking with the remote control.
Testing the doors:
1. Activate the alarm.
2. Wait 30 seconds.
3. Unlock with the key on the driver’s side.
4. Open one of the doors. The alarm should now be triggered.
5. Repeat the test for the other door.
6. Deactivate the alarm by unlocking with the remote control.
Testing the bonnet:
1. Get into the car and deactivate the movement detector as described on
page 80.
2. Deactivate the alarm (remain in the car and lock the doors with the
button on the remote control).
3. Wait 30 seconds.
4. Open the bonnet with the handle under the dashboard. The alarm
should now sound and flash.
5. Deactivate the alarm by unlocking with the remote control.
Testing the boot lid:
1. Activate the alarm.
2. Wait 30 seconds.
3. Unlock with the key on the driver’s side.
4. Open the boot lid. The alarm should now sound and flash.
5. Deactivate the alarm by unlocking with the remote control.
If the alarm system does not work correctly, have the car examined by an
authorised Volvo workshop.
85
86
Starting and driving
Starting the engine
88
Economical driving
89
Manual gearbox
91
Automatic gearbox
92
All-Wheel Drive (AWD)
94
Active chassis FOUR-C
95
Parking assistance
96
Towing
98
Jumpstarting
99
Driving with trailer
100
Towing bracket
102
Detachable towbar
104
Loading
106
Adjusting headlamp pattern
107
Brake system/ABS/EBD
110
Stability system
112
BLIS (Blind Spot Information System)
113
87
Starting the engine
NOTE! When the car is locked from outside,
the fuel filler flap remains unlocked for a
further 10 minutes.
Start the engine as follows
(Diesel)
Start the engine as follows
(Petrol)
1 Apply the parking brake (handbrake).
2 Automatic gearbox: Gear selector in P or
N position.
Manual gearbox: Gear lever in neutral
and the clutch pedal completely depressed.
This is especially important in severe cold.
3 Turn the ignition key to the driving position.
A control symbol in the combined instrument panel shows that the engine is preheating. Turn the key to the start position
when the indicator symbol has gone out.
1 Apply the parking brake (handbrake).
2 Automatic gearbox: Gear selector in P or
N position.
Manual gearbox: Gear lever in neutral
and the clutch pedal completely depressed.
This is especially important in severe cold.
3 Turn the ignition key to the start position. If
the engine does not start within 5-10 seconds,
release the key and try again.
2302129d
Refuelling
The fuel cap is inside the fuel filler flap on the
right rear wing.
In high exterior temperatures there can be
overpressure in the fuel tank. Open the filler cap
slowly.
Do not overfill the fuel tank. A maximum of
one automatic cut out by the fuel pump
nozzle is recommended! Too much fuel at high
outside temperatures can cause the tank to
overflow!
After refuelling, replace the fuel cap and turn
until one or more clicks is heard.
Opening fuel tank
The fuel filler flap is unlocked and can be
opened when the car is unlocked.
88
Refuelling
NOTE! Never add cleaning additives yourself
unless specifically recommended to do so by a
Volvo workshop.
Refuelling with diesel oil
At low temperatures (–5 °C to –40 °C) the
diesel oil can precipitate paraffin, which makes
the engine difficult to start. Make sure that
special winter fuel is used during the cold
period of the year.
Important!
Petrol-powered cars must always be refuelled
with unleaded petrol so as not to damage the
catalytic converter.
WARNING!
Always switch off your mobile telephone
during refuelling - the ring signal can cause
sparks which may ignite petrol fumes and
lead to fires or personal injury.
NOTE! Depending on the engine temperature
when starting, the idling speed with a cold start is
- for a short period - higher than normal for some
engine types.
The reason for this is Volvo's ambition to
minimise exhaust emissions by bringing up the
engine's exhaust purification system to its correct
working temperature as quick as possible.
Economical driving
Drive with anticipation
Economical driving results from driving gently
with anticipation and adapting your driving
style and speed to the situation.
Keep in mind the following:
· Drive the engine to operating temperature as
soon as possible! That is to say: do not let
the engine idle, but drive with a light load as
soon as you can.
· A cold engine consumes more fuel than a
warm one.
· Avoid driving short distances where the
engine never has time to reach operating
temperature.
· Drive gently! Avoid unnecessary quick
accelerations and heavy braking.
· Do not drive with unnecessary, heavy loads
in the car.
· Do not drive with winter tyres when the
roads are clear and dry.
· Remove the load carrier when it is not in use.
· Do not open side windows unnecessarily.
Your new car - slippery road
surfaces
Driving on a slipper road surface may feel
different depending on whether you have
chosen a car with manual gearbox or automatic
gearbox.
Practice handling skids under controlled
conditions so that you know how your new car
reacts.
Do not overload the battery
The electrical functions in the car load the
battery to varying degrees.
Avoid having the ignition key in position II
when the engine is off.
Use position I instead, as less power is
consumed. The 12-volt socket in the cargo
compartment supplies power even when the
ignition key is removed.
Examples of functions which consume a lot of
power:
· ventilation fan
· windscreen wipers
· audio system
· parking lamps.
Also take note of different accessories that load
the electrical system.
Do not use functions the consume a lot of
current when the engine is switched off.
A text is shown on the display in the combined
instrument panel if battery voltage is low.
The message in the display remains until the
engine has started.
The energy economy function shuts down
certain functions or reduces the load on the
battery, e.g. by lowering ventilation fan speed
and switching off the audio system.
Charge the battery by starting the engine.
89
Economical driving
Do not allow the engine and
cooling system to overheat
Under certain conditions, e.g. when driving in
hilly terrain and with a heavy load, especially in
warm weather, there is a risk of the engine and
cooling system overheating.
To prevent the cooling system from
overheating:
· Drive at low speeds if driving with a trailer
up a long incline.
· Switch off the air conditioning temporarily.
· Avoid letting the engine idle.
· Do not turn the engine off immediately you
stop, if the car has been driven hard.
· Remove any auxiliary lamps from in front
of the grille if driving in extremely high
temperatures.
To prevent the engine from overheating:
Do not exceed engine speeds of 4500 rpm
(diesel engine: 3500 rpm) if driving with a
trailer or caravan in hilly terrain. The oil
temperature can become too high.
Automatic gearbox
Adaptive system
The gearbox is controlled by what is known as
an adaptive system. The system continually
monitors how the gearbox is behaving
senses every gear change for optimum shift
quality.
90
Lock-up function
The gears have a lock-up function (locked
gears), which gives better engine braking and
lower fuel consumption.
Safety systems
Cars with automatic gearbox have special safety
systems:
Keylock
To remove the ignition key, the gear selector
must be in the P position.
The key is locked in all other positions.
Park position (P)
Stationary car with engine running:
Hold your foot on the brake pedal when
moving the gear selector to another position.
Shiftlock
Park position (P)
The brake pedal must be depressed to move the
gear selector from position P to other gear
positions when the ignition key is in position I
or II.
Neutral position (N position)
The brake pedal must be depressed to move the
gear selector from position N to other gear
positions when the ignition key is in position I
or II.
Cold start
When starting in cold temperatures, gear shifts
may feel harder.
This is due to the viscosity of the transmission
fluid at low temperatures.
To minimise engine emissions, the gearbox
shifts up later than normal if the engine has
been started at low temperatures.
When the engine is cold, the gearbox shifts
gears at higher revs.
This allows the catalytic converter to reach
normal operating temperature more quickly.
”Kick-down”
When the accelerator is pressed all the way to
the floor, beyond the position normally
regarded as full acceleration, a lower gear is
immediately engaged. This is known as kickdown.
When maximum speed for this gear is reached,
or if the accelerator is released from the kickdown position, the gearbox automatically
changes up.
Kick-down is used when maximum acceleration is needed, such as for overtaking.
To prevent over-revving, the gearbox control
program has a protective downshift inhibitor.
The kick-down function cannot be used in
the manual* positions. Return to automatic
position D.
* Refers to Geartronic.
Manual gearbox
M 56
68
64
72
76
68
80
64
72
M 56
68
76
64
80
72
76
68
80
64
72
76
80
4302395n
4301589e
Gear positions, 5-speed
Reverse gear inhibitor
Depress the clutch pedal fully with each gear
change. Remove your foot from the clutch
pedal between gear changes! Follow the
appropriate shifting pattern.
For the best possible fuel economy, use the
highest gear possible as often as possible.
Only engage reverse gear when the car is
stationary.
To put the car in reverse, the gear lever must
first be moved to neutral (between 3rd and 4th
gear). Thus, reverse cannot be directly selected
from 5th gear due to the reverse gear inhibitor.
91
Automatic gearbox
parking brake when the car is stationary with
the gear lever in N.
D – Driving position
D is the normal driving position. The car
automatically shifts between the different
gearbox gears based on the level of acceleration
and speed. The car should be stationary when
selecting D from position R.
4 – Low gear
Gear selector positions
P – Parking
Select this position when you wish to start the
engine or park the car.
The car should be stationary when you
select P!
In the P position the gearbox is mechanically
locked. Always apply the parking brake when
parking!
R – Reversing position
The car should be stationary when you
select R!
N – Neutral position
N is the neutral position. The engine can be
started, but no gear is selected. Apply the
92
Shifting up and down between the 1st, 2nd, 3rd,
and 4th occurs automatically.
The 5th gear will not be engaged.
Position 4 can be used:
· for mountain driving
· when driving with a trailer
· to increase engine braking
3 – Low gear
Shifting up and down between 1st, 2nd and
3rd occurs automatically.
The 4th gear will not be engaged.
Position 3 can be used:
· for mountain driving
· when driving with a trailer
· to increase engine braking
L – Low gear position
Select L if you wish to drive in 1st or 2nd.
Position L gives the best engine braking for
mountain driving, etc.
W – Winter
The W button by the gear
selector engages and
disengages the winter
programme W. The
symbol W is shown in the
combined instrument panel
when the winter programme is activated. The Winter programme starts
the gearbox in 3rd gear to make it easier to pull
off on slippery roads. When the programme is
engaged, lower gears are activated only by kickdown. The W programme can only be selected
in position D.
Automatic gearbox
68
64
72
76
68
80
72
76
80
4302476e
4302106d
Gear selector, automatic gearbox
64
Geartronic
4301647d
Gear selector, Geartronic
Mechanical gear selector inhibitor
Manual positions, Geartronic
While driving
The gear selector can be moved freely between
N and D. Other positions are locked with a latch
that is released with the inhibitor button on the
gear selector.
Press the inhibitor button to move the lever
forward or back between the different gear
positions.
Move the gear selector to the right to shift from
automatic driving position D to manual mode.
To shift from the MAN position to automatic
driving position D, move the gear selector left
to position D.
3rd gear is the highest gear that can be used
when starting.
The manual gearshift mode can be selected at
any time while driving. The engaged gear is
locked until you choose another gear. The car
will only shift down automatically if you slow
down to a very low speed.
If the gear selector is moved to - (minus) the car
changes down a gear and engine brakes at the
same time. If the gear selector is moved
to + (plus) the car changes up a gear.
The kick-down function cannot be used in
manual mode.
93
All Wheel Drive
All-Wheel Drive (AWD) (option)
All-wheel drive is always engaged.
All-wheel drive means that the vehicle is driven
by all four wheels at the same time.
The power is distributed automatically between
the front and rear wheels.
An electronically-controlled clutch system
distributes the power to the pair of wheels
which have the best grip in the road conditions.
This is to get the best possible grip and to avoid
wheelspin.
Under normal driving conditions, the majority
of power is transmitted to the front wheels.
The greater traction improves driving safety in
rain, snow and icy conditions.
94
Speed-dependent power
steering (option)
If the car is equipped with speed-dependent
power steering it is more easily steered at low
speeds to facilitate parking or the like.
When speed is increased, steering force is
adapted to provide the driver increased road
sensitivity.
Do not drive with an open boot
lid!
If you drive with the boot lid open, some of the
exhaust gases and poisonous carbon monoxide
can be sucked into the car through the cargo
compartment. If you must drive a short distance
with the boot lid open, do as follows:
· Close all windows.
· Distribute the air between the windscreen
and floor and while running the fan at high
speed.
Active chassis FOUR-C
Active chassis FOUR-C
(option)
The car is equipped with an extremely advanced
active chassis system - Continuously Controlled Chassis Concept - that is regulated electronically.
The FOUR-C control unit analyses data from
the sensors and performs the necessary shock
absorber setting adjustments up to 500 times
per second. This results in extremely fast and
accurate individual shock absorber control,
which contributes to variations in chassis
characteristics.
Chassis characteristics can be modified at any
time while driving, when the nature of the road
changes or when you desire a change in driving
style. This change occurs in a matter of
milliseconds.The effect produced by pressing
the accelerator is linked to your choice of
chassis characteristics.
Comfort
Comfort mode adjusts the
chassis setting so that the
body is insulated from
uneven sections of the road
surface, which allows for
better glide. Shock absorption
is softer and body movements are minimal.
This setting is recommended for long-distance
driving or driving on slippery road surfaces.
If the chassis is in Comfort mode when the
ignition is switched off, it will resume this
mode the next time it is started.
Sport
In Sport mode, steering responses are quicker
than in Comfort mode. Damping is harder and
the body follows the road surface to minimise
rolling during quick cornering. The car feels
sportier. If the chassis is in Sport mode when
the ignition is switched off, it will resume this
mode the next time it is started.
3603554m
95
Parking assistance
WARNING!
Parking assistance does not relinquish the
driver’s own responsibility during parking.
The sensors have blind spots where objects
cannot be detected.
Be aware of children and animals near the car.
3603495m
Parking assistance, front and rear
General
Parking assistance is used as an aid to parking.
A signal indicates the distance to an object.
The frequency of the signal increases a you
come closer to an object in front of or behind
the car. The tone becomes constant at a distance
of about 30 cm. If there are objects within this
distance both behind and in front of* the car, the
signal alternates between front and rear
speakers.
If the volume of another sound source from the
audio system is high, this is automatically
lowered.
The system is always activated when the car is
started.
*Provided that parking assistance is mounted
both front and rear.
96
Front parking assistance
The measurement area straight in front of the
car is approx. 0.8 m.
The text message PARK ASSIST ACTIVE
appears in the audio display when the sensors
react to an obstacle in front of the car.
Auxiliary lamps cannot be installed together
with parking assistance because the sensors
will react to the auxiliary lamps.
Rear parking assistance
The measurement area straight behind the car is
approx. 1.5 m.
The text message PARK ASSIST ACTIVE
appears in the audio display when reverse gear
is engaged.
The system must be deactivated when driving
with a trailer, bike carrier on the towbar or the
like as this would trigger the sensors.
Rear parking assistance is deactivated automatically when towing a trailer if a Volvo genuine
trailer cable is used.
3602947r
Deactivating and reactivating parking
assistance
Parking assistance can be deactivated with the
button in the switch panel. The LED in the
switch goes out. Parking assistance is reactivated when the switch is turned on and the
LED illuminates.
Front parking assistance
Front parking assistance is active at speeds of
below 15 km/h, even when reversing.
The signal comes from the front speakers.
Parking assistance
Rear parking assistance
Rear parking assistance is activated when
reverse gear is engaged.
The signal comes from the rear speakers.
Fault indicator
The information symbol
shines with a steady glow
PARK ASSIST SERVICE
REQUIRED is shown in the
information display in the
centre of the combined
instrument panel together with
the symbol.
3603503m
Parking assistance sensors
Cleaning the sensors
The sensors must be cleaned regularly in order
for them to function properly. Clean them with
water and car shampoo.
The sensors may react if covered by ice and
snow.
97
Towing
Bump starting (tow starting)
the engine
A
If you bump start (tow start) a car with manual
gearbox, the catalytic converter may be
damaged. Cars with automatic gearbox cannot
be bump started (tow started). Use a booster
battery if the battery is flat.
B
Towing eye
8600307e
Towing eye, front
If you need to be towed
· Unlock the steering wheel lock so that the
car can be steered.
· Keep in mind the highest permitted legal
towing speed.
· Remember that the brake and power
steering servos do not function when the
engine is switched off! You must exert
approximately five times more pressure on
the brake pedal and steering is considerably
harder than usual.
· Drive gently. Keep the towline taut to avoid
unnecessary jerking.
98
Towing eye, rear
For automatic gearboxes
· The gear selector should be in position N.
· Maximum permitted speed for cars with an
automatic gearbox: 80 km/h (50 mph).
Maximum permitted distance: 80 km
(50 miles).
· Cars equipped with an automatic gearbox
must only be towed face forward.
· The engine cannot be towed to start (bump
started). See “Jumpstarting” on the next page.
The towing eye is located in the tool kit in the
cargo compartment. You must screw the towing
eye into place before towing. The sockets and
covers for the towing eye are located on the
right-hand side of each bumper.
Remove the cover as follows:
A. Loosen the bottom edge of the cover with a
coin.
B. Screw the towing eye securely into place up
to the flange (C). You can use a wheelbrace.
After use, unscrew the towing eye and refit the
cover.
Towing
NOTE! The towing eye may only be used for
towing on the road, not for salvage after driving
into a ditch or similar. Professional help should
be called for salvage towing.
Jumpstarting
WARNING!
Remember that batteries, especially the booster battery, contain
oxyhydrogen which is highly explosive. A spark, which can be caused
if you incorrectly install the jump leads, is enough to cause the battery
to explode and both damage the car and injure you. The battery also
contains sulphuric acid, which can cause serious corrosive damage. If
the acid comes into contact with your eyes, skin or clothes, flush with
large quantities of water. If acid splashes into your eyes contact a
doctor immediately.
3100088m
Jumpstarting with a booster battery is as
follows:
If for some reason the battery in your car is discharged, you can “borrow”
current from a spare battery or another car’s battery to start the engine.
Always check that the clamps are secure so that there are no sparks
during the start attempt.
To avoid the risk of explosion, we recommend you do exactly as follows.
· Turn the ignition key to position 0.
· Ensure that the booster battery has 12 volt current.
· If the booster battery is in another car, stop the engine of that car and
make sure the cars are not touching.
· Connect the red cable to the booster battery’s positive terminal
(1+ in the illustration) and the connection in your cars engine
compartment (2+ in the illustration).
The clamp should be attached to the contact point located under a little
black cover with a plus sign on it. The cover is connected to the cover
of the fuse box.
· Connect one end of the black cable to the booster battery’s negative
terminal (3– in the illustration).
· Connect the other end of the black cable to a grounding point on your
car (4– in the illustration).
· Start the engine of the “booster car”. Let the engine run a few minutes
at a speed slightly higher than idle, 1500 rpm.
· Start the engine of the car with the discharged battery.
· NOTE! Do not move the clamps during the start attempt (risk
of spark buildup).
· Remove the clamps in reverse order.
NOTE! If you need to help another car, connect the red cable as shown in
the illustration above. Connect the black cable between two grounding
points as also shown in the illustration. Do not connect the black cable
to the negative pole of another battery!
99
Driving with trailer
Driving with trailer
· The towing bracket on the car must be of an approved type. Your
Volvo dealer can advise you as to which towing bracket to use.
· Distribute the load in the trailer so that the weight on the towing
bracket is approximately 50 kg for trailer weights under 1200 kg and
approximately 75 kg for trailer weights over 1200 kg.
· Increase tyre pressure to correspond to the pressure for full load. See
the tyre pressure table!
· Clean the towing bracket regularly and grease the towball* and all
moving parts to prevent unnecessary wear.
· Do not drive with a heavy trailer when your car is brand new! Wait
until it has gone at least 1000 km (620 miles).
· The brakes are loaded much more than usual on long and steep
downhill slopes. Downshift to a lower gear and adjust your speed.
· If the car is driven with a heavy load in a hot climate, the engine and
gearbox may overheat. The temperature gauge in the combined
instrument panel goes into the red zone when the car overheats. Stop
and let the engine idle a few minutes.
· If the car overheats, the air conditioning system can be temporarily
switched off.
· The gearbox reacts with a built-in protection function if the car
overheats. See the message in the display!
· The engine is loaded more heavily than usual when driving with a
trailer.
· For reasons of safety, you should not drive faster than 80 km/h
(50 mph), even if the laws of certain countries permit higher speeds.
· The highest permissible trailer weight for a trailer without brakes is
750 kg.
· If you park with a trailer, always move the gear selector to the P
position (automatic transmission), or engage a gear (manual gearbox).
If you park on steep hills always put chocks under the wheels.
* Does not apply to ball hitch with vibration damper.
100
· Avoid driving with trailer weights above 1200 kg on inclines great
than 12%. You should not drive with a trailer on inclines above 15%.
Driving with trailer - automatic transmission
· When parking on a slope you should apply the parking brake before
moving the gear selector to the P position. When starting on a slope
you should first move the gear selector to the driving position and then
release the parking brake.
· Select an appropriate low gear position on the gearbox when driving
on steep slopes or if driving slowly. In doing so, you prevent the
gearbox from changing up if you have an automatic transmission. The
gearbox oil will be cooler.
· If you have a Geartronic transmission, do not use a higher manual gear
than what the engine can "handle". It is not always economical to drive
in high gears.
NOTE! Some models must be fitted with an oil cooler for the automatic
transmission when driving with a trailer. You should therefore check with
your closest Volvo dealer about just your car if a towbar has been fitted at
a later date.
Driving with trailer
NOTE! The maximum permitted trailer weights stated are the ones
that the Volvo Car Corporation allows. Remember that national
vehicle regulations may further limit the trailer weight and speed.
The towbars can be certified for higher towing weights than what
the car may tow.
0300171d
The highest permitted trailer weight
for a trailer with brakes
Recommended
ball pressure
0-1200 kg.................................................... 50 kg
1201-1600 kg.............................................. 75 kg
1601-1800 kg.............................................. 75 kg
Level control
If your car is equipped with automatic level control, the rear end will
always have the right height while driving irrespective of the load. The
rear end drops when the car is at a standstill, which is quite normal. When
starting with a load, the level is pumped up after a certain distance.
WARNING!
If you do not follow the given recommendations, the trailer and car
may be difficult to control during evasive manoeuvres and braking,
which can be dangerous to you and others on the road.
101
Towing bracket
Fixed towbar (A)
A
Always remember to fasten the trailer's safety
cable to the attachment. See the illustration.
Detachable towbar (B)
Always follow installation instructions
carefully.
Always remember to fasten the trailer's safety
cable to the attachment. See the illustration.
Always remember to clean and grease the
connector pin regularly. Use the recommended grease 8624203.
B
8901313d
3701780d
NOTE! Your car may have a towing bracket
with a 13-pin electrical connector, which you
need to connect to a trailer with a 7-pin
electrical connector. If this is the case, use only
an original Volvo Genuine adapter cable.
Ensure that the cable does not drag on the
ground.
WARNING!
If your car is fitted with Volvo's detachable
towbar: Make sure that the towbar is locked
before you drive off.
· The red signal pin (see the arrow in the
illustration to the left) should not be visible!
· Use the key to lock it.
See the description on page 104.
102
Towing bracket
A
Distance A above:
Fixed:
Detachable:
Max. ball pressure:
1152 mm
1152 mm
B
8902082d
8902083d
Distance B above:
Fixed:
Detachable:
65 mm
65 mm
75 kg
103
Detachable towbar - mounting the ball section
1
2
3
OPEN
OPEN
B
8902079M
Remove the connector pin cover.
4
8902078M
Insert the key and turn it clockwise to the
unlocked position.
5
8902074M
Hold the towball and turn the lever clockwise
to the locked position. Release the lever.
6
LOCKED
PUSH
TO
LOCK
8902075M
Grasp the towbar.
Push the part with the ball in until it locks.
NOTE! The lever changes position quickly.
104
RED PIN (B)
NOT VISIBLE!
8902076M
Check that the signal pin (B) is pushed in.
8902076M
Turn the key anticlockwise to the locked
position and remove it from the lock.
Detachable towbar - removing the ball section
1
2
OPEN
3
OPEN
8902078M
Insert the key into the detachable part and turn
it clockwise to the unlocked position.
8902074M
Turn the lever clockwise to the locked position
and grip the towball.
8902081M
Grasp the towbar. Pull the towball section from
the connector pin. Do not hold the lever.
IMPORTANT!
The lock on the towball can only be locked
when the red plastic pin is not visible
4
LOCKED
8902077M
Turn the key anticlockwise to the locked
position and remove it from the lock.
5
8902080M
Refit the connector pin cover as in
the illustration.
105
Loading
1
8902060m
1
Load carrier attachment points
Loading
General
Load capacity is affected by extra accessories
mounted on the car, such as a towbar, the load
on the towball (75 kg with trailer hitched), load
carriers and roof box, as well as the passengers’
combined weight. The load capacity of the car
is reduced by the number of passengers and
their weight.
WARNING!
The car’s driving characteristics change
depending on how heavily it is loaded and
how the load is distributed.
106
Fitting the load carrier
1. Make sure the load carrier is placed in the
right direction (see the marking on the decal
under the cover).
2. Fit the guide pins into the guide holes (1).
3. Carefully lower the bracket on the other side
to the roof.
4. Screw the knob up a bit.
Press the knob against the roof bracket and
catch the hook in the roof bracket under
the roof rail.
5. Screw the load carrier in place.
6. Fit the guide pins of the other brackets into
the guide holes.
7. Screw the load carrier in place.
8. Check that the hook is properly secured in
the roof bracket.
9. Tighten the knobs alternately until the
carrier feels secure.
10. Refit the cover.
11. Check the knobs regularly to see that
they are properly tightened.
If using load carriers
· To avoid damaging your car and to achieve
the best level of safety when driving, we
recommend that you only use load carriers
that Volvo has specially designed for your car.
· Check periodically that the load carriers
and load are properly secured. Lash the
load securely with retaining straps!
· Distribute the load evenly over the load
carriers. Do not load lopsidedly! Place the
heaviest items at the bottom.
· Keep in mind that the car’s wind resistance
and fuel consumption increase in proportion
to the size of the load.
· Drive gently. Avoid quick accelerations,
heavy braking and taking curves hard.
WARNING!
Load no more than 100 kg on the roof,
inclusive of the load carriers or roof box.
The car’s centre of gravity and driving
characteristics are altered by roof loads.
Floor mats
Volvo offers custom made floor mats for your
car. They must be properly placed and secured
in the mat clips so that they do not become
entangled in the pedals at the driver’s seat or get
caught at other seats.
Adjusting headlamp pattern
X
X
X
X
Y
3501842m
X
3501716j
X
X
A. Headlamp pattern for left-hand traffic
B. Right-hand traffic
X
Y
Y
Correct light pattern for left or
right-hand traffic
So as not to dazzle oncoming drivers, the
headlamp beam pattern can be altered by
masking the headlamps. The quality of the
beam pattern may not be as good.
Headlamp masking
Copy the templates, which are reversed for
RHD variants, and transfer the pattern to a selfadhesive, waterproof material such as opaque
tape or similar. The mask is positioned using
the rectangle in the headlamp lens. The
reference measurements (X, Y) are for obtaining the distance from the rectangle to the corner
of the mask. After copying the templates, check
the measurements so that the reference measurements cover enough of the beam pattern.
3501841m
Fitting the mask to the headlamps. The upper illustration is for halogen headlamps and the lower
illustration is for Bi-Xenon headlamps.
Reference measurements for halogen
headlamps:
Reference measurements for Bi-Xenon
headlamps:
Template 1. (1) = 21 mm, (2) = 46 mm
Reference measurements to the rectangle in the
headlamp lens: (3) = 158 mm, (4) = 39 mm.
Template 3. (1) = 93 mm, (2) = 37 mm
Reference measurements to the rectangle in the
headlamp lens: (3) = 84 mm, (4) = 47 mm.
Template 2. (5) = 70 mm, (6) = 27 mm
Reference measurements to the rectangle in the
headlamp lens: (7) = 22 mm, (8) = 39 mm.
Template 4. (5) = 101 mm, (6) = 37 mm
Reference measurements to the rectangle in the
headlamp lens: (7) = 2 mm, (8) = 2 mm.
107
Adjusting headlamp pattern
Masking templates for halogen headlamps
The templates are for LHD variants, and are reversed for RHD variants.
Template 1 is fitted to the left-hand headlamp for LHD variants and on the right-hand
headlamp for RHD variants.
Template 2 is fitted to the right-hand headlamp for LHD variants and on the left-hand
headlamp for RHD variants.
3501843m
Copy templates 1 and 2. Check the measurements to ensure they are correct. Reverse the
templates for RHD variants. Transfer the template to a self-adhesive, waterproof material
and cut it out.
108
Adjusting headlamp pattern
Masking templates for Bi-Xenon headlamps
The templates are for LHD variants, and are reversed for RHD variants.
Template 3 is fitted to the left-hand headlamp for LHD variants and on the right-hand headlamp for RHD variants.
Template 4 is fitted to the right-hand headlamp for LHD variants and on the left-hand headlamp for RHD variants.
3501844m
Copy templates 3 and 4. Check the measurements to ensure they are correct. Reverse the templates for RHD variants. Transfer the template to a selfadhesive, waterproof material and cut it out.
109
Brake system/ABS/EBD
If a brake circuit fails
If a fault should occur in one of the
circuits it is still possible to stop the car. Press
the pedal hard once - not repeatedly. The brake
pedal can be depressed further and feels a little
softer than usual. If also requires more pressure
on the pedal to achieve a normal braking effect.
The brake servo only works when the
engine is running
If the car is rolling or being towed with the
engine switched off you must apply approximately five times more pressure on the brake pedal
than when the engine is running.
The brake pedal feels rigid and hard.
Moisture on the brake discs and brake
lining alter braking characteristics!
The brake components become wet when the
car is driven in heavy rain, through pools of
water, or when the car is washed. This alters
brake pad friction characteristics so that there is
a delay before braking effect is noticed. Depress
the brake pedal lightly from time to time when
driving long distances in rain or slush or before
parking the car in such conditions. The brake
pads are thus able to warm up and dry out. You
should also do this when driving after washing
the car or when starting in very damp or cold
weather conditions.
If the brakes are heavily loaded
When driving in the Alps or other roads with
similar characteristics, the brakes are heavily
loaded even if you are not pressing the pedal
110
particularly hard. Because the speed is often
low the brakes are not cooled as effectively as
when driving on flat roads.
So as not to overload the brakes shift down
and use the same gear both uphill and downhill
instead of using the brake (manual transmission). In this way engine braking is used more
effectively and the brake is only required for
short periods.
Keep in mind that the brakes are even more
heavily loaded when driving with a trailer.
ABS - Anti-lock brakes
The ABS system (Anti-lock Braking System) is
designed so that the wheels do not lock when
braking. This retains the best possible steering
response when braking. This improves your
ability to swerve to avoid obstacles. The ABS
system does not increase your total braking
capacity. However, as the driver you have
increased ability to steer and thus better control
over the car, which in turn increases safety.
After the engine has started and reached a speed
of about 20 km/h (12 mph), a short self-test can
be both heard and felt. When the ABS system
functions, you can hear and feel pulses in the
brake pedal. This is completely normal.
NOTE! You must depress the brake pedal fully
to take maximum advantage of the ABS system.
Do not release the pedal when the ABS pulses
are felt and heard. Practice braking with the
ABS system in a suitable place.
The ABS symbol is lit and shines with a
constant glow:
· For approximately two seconds when you
start the car to test the system.
· If the ABS system has shut down due to a
fault.
Brake system/ABS/EBD
Electronic Brakeforce
Distribution (EBD)
The EBD system (Electronic Brakeforce
Distribution) is an integrated part of the ABS
system. The EBD system controls the brake
force to the rear wheels so that the best possible
braking force is always available. Pulses in the
brake pedal can be felt and heard as the system
controls the brake force.
WARNING!
If both the BRAKE
and ABS
warning symbols are lit, there is a risk that the
rear end will have a tendency to slide during
heavy braking.
If the level in the brake fluid reservoir is normal, drive carefully to the nearest authorised
Volvo workshop to have the brake system
checked.
If the level of brake fluid in the reservoir is below
the MIN mark, the car should not be driven until
the brake fluid has been topped up.
The reason for the loss of brake fluid must
be investigated.
Emergency Brake Assistance (EBA)
The Emergency Brake Assistance function is
integrated in the DSTC system.
The system is designed to provide maximum
brake force immediately whenever rapid
braking is necessary. The system detects the
need for heavier braking by registering how
quickly the brake pedal is applied.
The EBA function is active at all speeds. For
safety reasons, it cannot be switched off.
When the EBA function is activated, the brake
pedal sinks while maximum braking force is
applied.
Continue braking without releasing the brake
pedal.
The EBA function disengages when the
pressure on the brake pedal is relieved.
111
Stability system
When the stability system is in action, it may
seem like the car does not respond normally to
acceleration. This is because the system detects
the amount of friction on the road surface and
allows the different stability system functions to
operate.
The car is equipped with either STC (Stability
and Traction Control) or DSTC (Dynamic
Stability and Traction Control).
Function/system
STC
DSTC*
TC
SC
AYC
X
X
X
X
X
Traction Control (TC)
The Traction Control function transfers power
from the spinning drive wheel to the drive wheel
which has grip by braking the spinning drive
wheel. To increase forward traction in this
situation, it may be necessary to depress the
accelerator more than usual. A pulsing sound is
heard when Traction Control is working. This is
completely normal. The TC function is most
active at low speeds. It cannot be deactivated.
Spin Control (SC)
The Stability Control function prevents the drive
wheels from slipping during acceleration.
This improves road safety on slippery surfaces.
Under certain conditions, such as when driving
with snow chains or in deep snow or sand, it
may be beneficial to deactivate the SC function
to increase traction. This is done with the
STC/DSTC button.
WARNING!
The driving characteristics of the car may
change if the STC or DSTC is reduced. Always follow normal safety precautions for
cornering and driving on slippery surfaces.
* Option on certain markets
112
Active Yaw Control (AYC)
The Active Yaw Control function automatically
brakes one or more wheels to stabilise the car in
the event of a skid. If the brake pedal were to be
depressed in this situation, it would feel more
rigid than usual and a pulsing sound would be
heard.
The AYC function is always active and cannot
be deactivated.
BLIS (Blind Spot Information System)
B
A
3603686j
3603683r
1 - BLIS camera, 2 - Indicator lamp,
3 - BLIS symbol
“Blind spots” covered by BLIS
Distance A = approx. 9.5 m
Distance B = approx. 3 m
BLIS
BLIS is an information system which indicates
whether there is another vehicle moving in the
same direction in the so-called ”blind spot”.
WARNING!
The system is a supplement to, and not a
replacement for, the existing rearview
mirrors. It can never replace the awareness
and responsibility of the driver. The
responsibility for changing lanes safely rests
with the driver.
The system is designed to work most effectively when driving in dense traffic on multi-lane
highways. BLIS is based on digital camera
technology. The cameras (1) are fitted under the
door mirrors.
When a camera has detected a vehicle inside the
blind spot zone then an indicator lamp is lit in
the door panel (2). The light comes on with a
constant glow to draw the driver’s attention to a
vehicle in the blind spot.
NOTE! The lamp comes on on the side of the
car where the system has detected the vehicle. If
the car is overtaken on both sides at the same
time then both lamps come on.
BLIS also has an integrated function which
warns the driver if a fault should arise in the
system. If, for example, the system’s cameras
are obscured then the BLIS indicator lamp
flashes and a message is shown in the
dashboard display (see the table on page 115).
In such cases, check and clean the lenses. If
necessary, the system can be switched off
temporarily by pressing the BLIS button (see
page 114).
When BLIS operates
The system operates when the car is driven at a
speed above 10 km/h.
When you overtake another vehicle:
· The system reacts if you overtake another
vehicle at a speed of up to 10 km/h faster
than the other vehicle.
When you are overtaken by another vehicle:
· The system reacts if you are overtaken by a
vehicle travelling up to 70 km/h faster than
you are travelling.
WARNING!
· BLIS does not work in sharp bends.
· BLIS does not work when the car is
reversing.
· A wide trailer coupled to the car can
conceal other vehicles in adjacent lanes. It
can prevent the vehicle in the screened area
from being detected by BLIS.
113
BLIS (Blind Spot Information System)
System function in daylight and
darkness
Daylight
In daylight the system reacts to the shape of the
surrounding vehicles. The system is designed
to detect motor vehicles such as cars, trucks,
buses and motorcycles
Darkness
In darkness the system reacts to the headlamps
of surrounding vehicles. If its headlamps are
not switched on then the system does not detect
the vehicle. This means for example that the
system does not react to a trailer without
headlamps which is towed behind a car or
truck.
Cleaning
In order to work most effectively the BLIS
camera lenses must be clean. The lenses can be
cleaned with a soft cloth or damp sponge. Clean
the lenses carefully so that they are not
scratched.
Important!
The lenses are electrically heated to melt ice
or snow. If necessary, brush snow away
from the lenses.
114
WARNING!
· The system does not react to bicycles or
mopeds.
· The BLIS cameras can be disrupted by
intensive light or when driving in the dark
when there are no light sources (e.g. street
lighting or other vehicles). The system may
then interpret the lack of light as if the
cameras have been blocked.
In both cases a message is shown in the
dashboard display.
When driving in such conditions the
system can be temporarily switched off
(see the information to the right).
When the text message has faded the
system returns to full functionality.
· The BLIS cameras have the same limitations as the human eye, i.e. they ”see”
worse in heavy snowfall or thick fog for
example.
3603682r
Deactivating and reactivating BLIS
· BLIS is activated automatically each time
the ignition is switched on. The indicator
lamps in the door panels flash three times
when the ignition is switched on.
· The system can be switched off by pressing
the BLIS button in the switch panel in the
centre console (see illustration above). The
LED in the button goes out when the
system is switched off and a text message is
shown in the dashboard display.
· BLIS can be reactivated by pressing the
button. An LED in the button then lights, a
new text message is shown in the display
and the indicator lamps in the door panels
flash three times. Press the READ button,
see page 37, to clear the text message.
BLIS (Blind Spot Information System)
BLIS system messages
System status
Text in the display
BLIS system not
functioning
BLIND-SPOT SYST
SERVICE REQUIRED
Right-hand
camera blocked
BLIND-SPOT SYST R
CAMERA BLOCKED
Left-hand camera
blocked
BLIND-SPOT SYST L
CAMERA BLOCKED
BLIND-SPOT SYST
CAMERAS BLOCKED
Both cameras
blocked
BLIS system off
BLIND-SPOT INFO
SYSTEM OFF
BLIS system on
BLIND-SPOT INFO
SYSTEM ON
BLIS function
BLIS FUNCTION
REDUCED
reduced
The messages above are only shown if the
ignition key is in position II (or if the engine is
running) and BLIS is active (i.e. if the driver
has not switched off the system).
115
116
Wheels and tyres
General about wheels and tyres
118
Tyre pressures
120
Wear, Changing the tyres, Spare wheel
121
Changing wheels
122
117
General
General wheels and tyres
New tyres
All tyres have a dimension designation, such as 215/55R16 93W.
Bear in mind that tyres are perishable goods - after a
few years they begin to harden while their friction
properties deteriorate little by little. Try to use fresh
tyres when changing.
This is especially important for winter tyres. The week
and year of manufacture is indicated with 4 digits (e.g.
1502 indicates tyres manufactured week 15, 2002).
These tyre size designations, which are used by all tyre manufacturers,
can be interpreted as follows:
215
section width (mm)
55
relationship between the section height and breadth (%)
R
means radial tyre
16
wheel rim diameter in inches (")
93
code digits for maximum permissible tyre load, in this
case 650 kg
W
specifies that the tyre is manufactured for speeds up to
270 km/h (167 mph)
Your car is fully approved, which means that you may not deviate from
those dimensions and performance ratings indicated in the vehicle
registration. The only exception from these regulations concerns winter
tyres and studded tyres, which may have different dimensions and a
different speed rating than indicated in the registration. If you select tyres
with different dimensions, do not drive at speeds faster than those
permitted. The most common speed ratings are indicated in the following
table:
Note: maximum permissible speeds indicated.
Q
160 km/h, used most often with studded tyres
T
190 km/h
H
210 km/h
V
240 km/h
W
270 km/h
When you change tyres: be sure to use the same type (radial), dimension,
designation, and brand on all four wheels. Otherwise, there is a risk that
the handling characteristics of the car could change. Check with your
dealer regarding dimensions which are available for your car. Keep in
mind that the road surface can determine how fast you may drive, not the
tyre speed rating.
118
7700444d
Tyre age
All tyres older than six years should be checked by
an expert even if they seem undamaged. The reason
for this is that tyres age and decompose, even if
they are hardly ever or never used. The function can
therefore be affected due to the tyre’s constituent
materials being broken down, and it should then not
be used.
This also applies to spare tyres, winter tyres and
tyres saved for future use.
Examples of external signs which indicate that the
tyre is unsuitable for use are cracks or discolouration.
The age of the tyre can be determined by the
marking, see illustration.
General
Winter tyres
Locking wheel bolts
We recommend the use of winter tyres, size 195/65 R15 except for cars
with turbo engines. For these cars we recommend tyre size 205/55 R16.
Always use winter tyres on all four wheels!
NOTE! Always consult your Volvo dealer as to which wheel and tyre
type is appropriate for your car.
Locking wheel bolts can be used on both aluminium and steel rims.
If steel rims with locking wheel bolts are used in combination with wheel
covers then the locking wheel bolts must be fitted furthest from the air
valve. Otherwise the wheel cover cannot be fitted on the rim.
Studded winter tyres
Studded winter tyres should be run in for 500-1000 kilometres
(300-600 miles), softly and gently so that the studs sit in the tyre correctly.
This extends the service life of both the tyres and the studs while making
the drive a bit quieter. Ensure that the studded tyres have the same
direction of rotation throughout their lifetime. If you wish to shift wheels,
see to it that they remain on the same side as previously.
Please remember: The regulations for using studded tyres vary from
country to country.
Snow chains
Snow chains may only be used on the front wheels. This also applies to
all-wheel drive cars.
Avoid driving on bare surfaces unnecessarily as this generates much wear
on both the snow chains and the tyres.
Important!
Only Volvo-approved snow chains are permitted. Use of other snow
chains could damage your car.
Never drive faster than 50 km/h when snow chains are fitted!
Never use ”quick links” because the space between the disc brakes
and the wheels is too small.
119
Tyre pressures
1:1
1:2
8904041n
1. Other markets (not USA, Canada)
1:1. Volvo original tyre
1:2. Spare tyre
2. Australia
Driving characteristics and tyres
Tyres affect driving characteristics greatly. Tyre type, size and pressure are
important to how the car performs. When you change tyres, be sure to use
the same type, size and brand on all four wheels. Follow the recommendations regarding tyre pressure.
The tyre pressure is important!
Check the tyre pressure regularly. The correct pressure is listed in the
adjacent table and on the decal on the inside of the fuel filler flap.
If you drive with tyres at the wrong pressure, the car’s handling will
be markedly impaired and tyre wear will increase.
Note that the values in the table refer to cold tyres (outside temperature).
Tyres get warm and pressure increases after just a few kilometres driving.
This is normal, so do not let out air if you check the pressure when the
tyres are warm. However, you should increase pressure if it is too low.
120
Remember that tyre pressure can vary depending on exterior temperature.
Therefore check the tyres outdoors when the tyres are cold.
Tyre pressure table
The tyre pressure decal on the inside of the fuel filler flap shows what
pressure the tyres should have with different load and speed conditions.
WARNING!
The only Volvo approved “special wheel rims” are those tested by Volvo
and are Volvo Genuine accessories.
Wheels and tyres
Tyres with tread wear
indicators
Tread wear indicators are narrow, raised areas
across the tread that have approximately
1.6 mm less tread depth than the remainder of
the tyre (the letters TWI are on the side of the
tyre). When this bar is visible, only 1.6 mm of
tread remains and the tyre should be replaced
immediately. Bear in mind that road grip and
the tyre's ability to push water out of the way is
already affected markedly when there is 3-4 mm
of remaining tread.
Spare wheel “Temporary Spare” (certain variants
and markets)
The “Temporary Spare” should only be used for the short time it takes to
repair or replace the normal tyre.
By law it is only legal to temporarily use the spare wheel/tyre in
connection with tyre damage. A wheel/tyre of this type should
therefore be replaced by a normal wheel/tyre.
7700312m
Changing the tyres - summer/winter
When you change between summer and winter tyres; mark on the tyre
which side they were fitted: For example, L = left, R = right.
Bear in mind that this tyre combined with the other normal tyres may
cause different driving characteristics.
The maximum speed with a “Temporary Spare” is therefore
80 km/h (50 mph).
NOTE! Only use the car’s original spare wheel! Tyres of other dimensions may damage your car. Only one spare wheel may be used at a time.
NOTE! Tyres should have the same direction of rotation throughout their
life. Tyres with tread designs that are made to roll only in one direction,
have the direction of rotation marked with an arrow on the tyre.
If the tyres are fitted incorrectly this will impair the car's braking characteristics and the ability to disperse rain, snow and slush.
IMPORTANT!
Tyres with the greatest tread depth should always - irrespective of rear
or front wheel drive - be fitted at the rear.
Contact your closest Volvo dealer to check if you are unsure.
Storage
Wheels should be stored horizontally or suspended, not vertically.
121
Changing wheels
7700
7700
7700401r
Remove wheel studs
The spare wheel is stored under the carpet in the cargo compartment.
Remember to set out the warning triangle.
· Apply the parking brake and put into first gear on cars with manual
transmission - position P on cars with automatic transmission.
Put chocks in front and behind of the wheels that are to remain on the
ground.
· Cars with steel wheel rims have removable wheel covers. Prise off
the wheel cover with a thick screwdriver or the like. If tools are not
available, the wheel cover can be prised off by hand. Use protective
gloves. When you reinstall the wheel covers: ensure that the wheel
cover valve hole is opposite the wheels air valve.
122
· Cars with aluminum rims with a cover: remove the cover using the
socket wrench.
· Loosen the wheel nuts 1/2-1 with the socket wrench. The nuts are
loosened by turning anticlockwise.
There are two jacking points on each side of the car. The jacking points
are marked on the door sill trims.
Changing wheels
WARNING!
· Never crawl under the car when it is raised on a jack!
· The car and the jack should be on a solid horizontal surface.
· The car original jack should be used for wheel changing.
All other work on the car should be carried out using workshop
jacks and axle stands under the part of the car which is raised.
· Apply the parking brake, put into 1st gear or back up (reverse)
on manual transmission and position P on the automatic
transmission.
· Put chocks in front of and behind the wheels to remain on the
ground.
· Use large wooden blocks or large stones.
· The jack screw should be kept well lubricated.
7700245d
7700244d
The jack should be located so
· Hold the jack against the pin in the jacking point as illustrated and
wind down the jack foot so that it is pressed flat against the
ground.
· Check again that the jack is mounted correctly according to
illustration and that the foot is positioned vertically under
mounting.
· Lift the car so that the wheel is free.
· Remove the wheel studs and lift off the wheel.
Fitting
· Clean the contract surfaces on the wheel and hub.
· Mount the wheel and tighten the wheel bolts.
· Lower the car so that the wheels cannot rotate. Tighten the wheel studs
crosswise and in torque steps. Tightening torques: 140 Nm
(14.0 kpm). It is important that they are tightened to the correct torque.
Tightening should be checked with a torque wrench.
· Fit the hub cap.
· Screw the jack together before returning it to the cargo compartment.
· Ensure that the jack and tool kit are properly secured and do not cause
any rattling.
123
124
Fuses, bulb replacement
Fuses
126
Relay/fuse box in the engine compartment
127
Fuses in the passenger compartment at dashboard end on driver’s side
128
Fuses in the passenger compartment within the sound
barrier on the driver’s side
129
Fuses in the cargo compartment
130
Bulb replacement
131
125
Fuses
3703474d
All electrical functions and components are
protected with a number of fuses to protect
your car’s electrical system from damage by
short-circuits or overloads.
Fuses are housed in four different locations in
the car:
1. Relay/fuse box in the engine compartment.
2. Fuse box in the passenger compartment
within the sound barrier on the driver’s
side.
3. Fuse box in the passenger compartment at
dashboard end on driver’s side.
4. Fuse box in the cargo compartment.
126
If an electrical component or function does not
operate it may be because the component fuse
was temporarily overloaded and burned out.
Look in the fuse diagram to locate the affected
fuse. Pull out the fuse and look at it from the
side to see if the curved wire is burned out.
Replace with a new fuse of the same colour and
ampere designation.
There are a number of spare fuses in the cover
on the end of the dashboard. There are also
pliers to assist you in pulling out and replacing
the fuses.
If the same fuse burns out repeatedly, there is a
fault in the component, and you should visit
your Volvo workshop to have it checked.
Fuses in the engine compartment
Fuses in the engine compartment
This fuse box contains 24 fuse positions. Be
sure to replace a blown fuse with a new fuse of
the same colour and amperage. There are also a
number of spare fuses.
9
8
7
6
21 17 13
Fuse pliers
20 16 12
5
4
3
19 15 11
Intact fuse
18 14 10
2
1
Blown fuse
3703757m
No
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Ampere rating
ABS ...................................................... 30
ABS ...................................................... 30
– .............................................................. –
Parking heater (option) ........................ 25
Auxiliary lamps (option) ..................... 20
Starter motor relay ............................... 35
Windscreen wipers .............................. 25
– .............................................................. –
Fuel pump ............................................ 15
Ignition coils (petrol), engine control
module (ECM), injection valves (diesel),
fuel pressure regulator .......................... 20
11. Accelerator pedal sensor (APM), AC
compressor, electronics box fan ........... 10
12. Engine control module (ECM) (petrol),
injection valves, (petrol),
mass air flow sensor (petrol) ............... 15
mass air flow sensor (diesel) .................. 5
13. Electronic throttle module (ETM),
solenoid valve ....................................... 10
14. Lambda-sond (petrol) .......................... 20
15. Crankcase ventilation heater, solenoid
valves, glow plugs (diesel) coil ............. 10
16. Dipped beam (left) ............................... 20
17. Dipped beam (right) ............................. 20
18. – .............................................................. –
19. Engine control module (ECM) supply
(petrol), engine relay .............................. 5
20. Position lamps ..................................... 15
21. – .............................................................. –
127
Fuses in the passenger compartment at dashboard end on driver’s side
1
10
20
30
2
11
21
31
3
12
22
32
4
13
23
33
5
14
24
34
6
15
25
35
7
16
26
36
8
17
27
37
9
18
28
38
19
29
Decal located in the end box cover. Indicates
positions and amperages
3701482D
This fuse box contains 38 fuse positions. Fuses
are located inside the access panel on the end
face of the dashboard. There are also a number
of spare fuses.
No
Ampere rating
1. Power driver’s seat ............................... 25
2. Power passenger seat ........................... 25
3. Climate control system fan ................... 30
4. Control module, right front door .......... 25
5. Control module, left front door ............ 25
6. General lighting, ceiling (RCM),
Upper Electronic Module (UEM) ........ 10
7. Sunroof ................................................. 15
8. Ignition switch, SRS system, Engine
Control Module (ECM), SRS
deactivation on passenger side
(PACOS), immobilizer (IMMO) ........ 7,5
128
9. OBDII, light switch (LSM), Steering
Angle Sensor (SAS), Steering Wheel
Module (SWM) ...................................... 5
10. Audio .................................................... 20
11. Amplifier .............................................. 30
12. RTI display ........................................... 10
13. Telephone ................................................ 5
14 - 38 –. ......................................................... –
Fuses in the passenger compartment within the sound barrier on the driver’s side
This fuse box contains 36 fuse positions. The
fuses are located within the sound barrier on the
left-hand side. Be sure to replace a blown fuse
with a new fuse of the same colour and
amperage. Several spare fuses are found here as
well.
1
3
4
5 6
7
8
2
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30
3703457r
No
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Ampere rating
Seat heating, right side .......................... 15
Seat heating, left side ............................ 15
Horn ..................................................... 15
– .............................................................. –
– .............................................................. –
Reserve ................................................... –
Reserve ................................................... –
Alarm siren ............................................. 5
Brake lamp switch feed .......................... 5
Combined instrument panel (DIM),
climate control (CCM), parking heater,
power driver’s seat ............................... 10
Front and rear seat socket ..................... 15
– .............................................................. –
Reserve ................................................... –
Headlamp wipers .................................. 15
ABS, STC/DSTC ................................... 5
16. Bi-fuel, Electronically Controlled Power
Steering (ECPS), Bi-Xenon, headlamp
levelling ................................................ 10
17. Fog lamp, front left .............................. 7,5
18. Fog lamp, front right ........................... 7,5
19. Reserve ................................................... –
20. Reserve ................................................... –
21. Transmission Control Module (TCM),
reverse gear inhibitor (M66) ................ 10
22. Main beam, left ..................................... 10
23. Main beam, right .................................. 10
24. – .............................................................. –
25. – .............................................................. –
26. Reserve ................................................... –
27. Reserve ................................................... –
28. Power passenger seat, audio .................. 5
29. Reserve ................................................... –
30.
31.
32.
33.
34.
35.
36.
BLIS ....................................................... 5
Reserve ................................................... –
Reserve ................................................... –
Vacuum pump ...................................... 20
Washer pump, headlamp wipers ........... 15
– .............................................................. –
– .............................................................. –
129
Fuses in the cargo compartment
The fuses are located behind the upholstery on
the left-hand side. Be sure to replace a blown
fuse with a new fuse of the same colour and
amperage.
No
Ampere rating
1. Reversing lamp ..................................... 10
2. Parking lamps, fog lamps, cargo
compartment lighting, numberplate
lighting, LEDs in brake lighting ........... 20
3. Accessories (AEM) .............................. 15
4. Reserve ................................................... –
5. REM electronics ................................... 10
6. CD changer, TV, RTI ........................... 7,5
7. Towing bracket wiring (30-feed) .......... 15
8. Cargo compartment socket ................... 15
9. Rear right door: power window,
power window lock .............................. 20
10. Rear left door: power window, power
window lock ......................................... 20
11. Reserve ................................................... –
12. Reserve ................................................... –
13. Diesel filter heater ................................. 15
14. – .............................................................. –
15. Reserve ................................................... –
16. Reserve ................................................... –
17. Audio accessories ................................... 5
18. Reserve ................................................... –
130
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
Foldable head restraint .......................... 15
Towing bracket wiring (15-feed) ......... 20
Reserve ................................................... –
– .............................................................. –
AWD ................................................... 7,5
Four-C SUM ........................................ 15
– .............................................................. –
Parking assistance .................................. 5
Main fuse: towing bracket wiring,
Four-C, parking assistance ................... 30
Central locking system (PCL) .............. 15
Trailer lighting, left: parking lamp,
direction indicator ................................. 25
Trailer lighting, right: brake lamp, fog
lamp, direction indicator ....................... 25
Main fuse: Fuse 37, 38 ......................... 40
– .............................................................. –
– .............................................................. –
– .............................................................. –
– .............................................................. –
– .............................................................. –
Rear window defroster ......................... 20
Rear window defroster ......................... 20
1 2 3 4 5
6 7 8 9 101112
13141516171819
202122
27 28 29 30
23242526
31
32 33 34 35 36
37
38
3703477d
Replacing bulbs
General
All bulb specifications are found on page 166.
The following list contains bulbs and pointsource lamps that are specialised or unsuitable
for changing except by a workshop:
· General interior lighting in the ceiling
· Ceiling lighting
· Reading lamps
· Glovebox lighting
· Direction indicators in the door mirrors
· Approach lighting in the door mirrors
· High-level brake light
· Bi-Xenon headlamps
3500534d
Important!
Never touch the bulb glass with your fingers. Grease and oils from your fingers are
vaporised by the heat, coating and damaging
the reflector.
WARNING!
On cars with Bi-Xenon headlamps, all
work on the lights should be carried out by
an authorised Volvo workshop.
Bi-Xenon headlamps must be handled
with extreme care due to the high-voltage
unit.
131
Replacing bulbs
1
1
2
2
3
4
3
TOP
4
3500903d
3500535d
Dipped and main beam
Replace headlamp bulbs from the engine
compartment.
· Switch off all lights and turn ignition key
to position 0!
· Open the bonnet.
· Remove the cover by twisting
anticlockwise (1).
· Pull off the connector (2).
· Disconnect the spring clamp. First push to
the right so that the spring disconnects and
then out and down (3).
· Pull the bulb out and replace with a
new one (4).
· Replace the bulb (1). It can only be fitted
in one position.
132
3500536d
· Press the clamp spring upwards and a little
to the left so that it secures in its catch (2).
· Press the connector back into place (3).
· Screw the cover back into place; “TOP”
should be upwards (4)!
Front position/parking lamp*
· Switch off all lights and turn ignition key to
position 0.
· Remove the main headlight cover by
turning it anticlockwise.
· Pull out the bulb and its socket. Replace the
bulb.
· Press the bulb and its socket back into
place.
· Check that the new bulb lights.
· Screw the cover back into place; “TOP”
should be up!
Replacing bulbs
1
2
3
4
3500893d
5
3501688d
Replacing bulb in front corner
· Switch off all lights and turn ignition key to
position 0.
· Using a screw driver, press the guide lug
and pull out the entire lamp housing.
· Press down the spring clip and undo the
connector from the lamp housing.
· Twist the bulb holder anticlockwise and
remove it.
· Press the bulb inwards, turn it anticlockwise
and remove it from the bulb holder.
· Replace with a new bulb and refit the bulb
holder in the lamp housing.
· Press the connector back onto the lamp
holder.
· Switch on the ignition and check that the
new bulb lights.
· Press the lamp housing home and check that
it is seated securely.
Replacing bulbs in the rear
lamp cluster
All bulbs in the rear lamp cluster can be
replaced from inside the cargo compartment.
· Switch off all lights and turn ignition key to
position 0.
· Unlock and fold down the side panel
inwards to allow access to the bulbs. On the
right-hand side, it is easier to access the
bulbs if you first extend the load curtain as
much as possible.
The bulbs are located in a removable lamp
holder which is secured with two locking pins.
To replace bulbs in the lamp holder:
· Press the locking pins towards one another
in order to remove the lamp holder from the
lamp housing.
· Replace the bulb.
· Press back the lamp holder.
· Close and secure the side panel.
Left-hand rear edge of car
Location of bulbs in rear lamp
cluster
1. Position lamp
2. Position/Parking lamp/
Foglampbulb
3. Position
4. Reversing lamp
5. Position (side marker) light
NOTE! If the error message "LAMP
FAULT" / "CHECK BRAKE
LIGHT" remains after a faulty bulb
has been replace then an authorised
Volvo workshop needs to be consulted
to rectify the fault.
NOTE! LED brake light bulbs should be
replaced at a Volvo workshop.
133
Replacing bulbs
3500894d
3500903d
3500889d
Replacing front fog lamp bulb
NOTE! Never touch the bulb glass with
your fingers.
· Switch off the lights and turn the ignition
key to position 0.
· Turn the bulb holder a little anticlockwise.
· Remove the bulb and replace with a new.
· Refit the bulb holder. (The profile on the
bulb holder aligns with the profile on the
base of the lamp).
· Replace the bulb holder by turning a little
clockwise. The marking "TOP" on the
headlamp cover should be upwards!
134
Replacing side
direction indicator bulb
Replacing position/
parking lamp bulb
· Open the front door halfway.
· Insert your hand behind the front wing and
press out the lamp. Allow the cables to
remain in the bulb holder.
· Twist the bulb holder 1/4 turn anticlockwise
and pull straight out.
· Pull the defective bulb straight out.
· Replace the bulb and press the lamp
straight in.
· Switch off all lights and turn ignition key
to position 0.
· Remove the main headlight cover by turning
it anticlockwise.
· Pull out the bulb and its socket. Replace
the bulb.
· Press the bulb and its socket back into
place.
· Check that the new bulb lights.
· Screw the cover back into place; “TOP”
should be up!
Replacing bulbs
3500888D
3500871d
3500916d
Replacing numberplate
lighting bulb
Replacing courtesy lighting
bulb - front door
Replacing courtesy lighting
bulb - rear door
· Switch off the lights and turn the ignition
key to position 0!
· Remove the screw with a screwdriver.
· Loosen the whole lamp housing carefully
and pull it out.
· Turn the connector anticlockwise and pull
out the bulb.
· Replace bulb.
· Reinstall the connector and turn it clockwise.
· Reinstall and screw the whole lamp housing
into place.
The courtesy lighting is under the dashboard
on the driver’s and passenger sides. Carry out
the following to replace:
·
·
·
·
Insert a screwdriver and twist lightly so
that the lamp housing loosens.
Remove the faulty bulb and install a new
bulb.
Check that lamp lights and reinstall the
lamp housing.
·
·
·
Insert a screwdriver and twist lightly so that
the lamp housing loosens.
Undo the cable from the lamp housing and
then remove the glass from the lamp
housing by pressing the two side clips
outward.
Pull out the old bulb and fit a new one.
Refit in the reverse order.
135
Replacing bulbs
3500891d
3500918d
3501378m
Insert screwdriver and turn carefully
Replacing side marker bulb
·
·
·
·
·
·
136
Press the entire lamp insert backwards and
remove.
Try if possible to remove the lamp insert
with your fingers. Otherwise, use a plastic
or wooden tool so as not to damage the
paintwork.
Turn the lamp holder anticlockwise and
remove.
Install a new bulb.
Insert the lamp holder and turn it clockwise.
Refit the lamp insert by pressing it into
place in the body.
Replacing the make up-mirror
bulb
Replacing cargo
compartment bulb
·
The lighting is to the left and right of the boot
lid. Carry out the following to replace:
·
·
Insert a screwdriver and gently turn so that
the glass loosens.
Prise out the bulb and replace with a new
one.
Press the lamp glass back into place and
make sure it is secured correctly.
·
·
·
Insert a screwdriver and twist lightly so that
the lamp housing loosens.
Remove the faulty bulb and install a new
bulb.
Check that the lamp lights and reinstall the
lamp housing.
Car care and Service
Rustproofing
138
Checking and repairing paintwork damage
139
Washing
140
Volvo Service
143
Bonnet, Engine Compartment
145
Diesel
147
Engine oil
148
Coolant
150
Brake fluid, Power steering, Windscreen washer fluid
151
Battery care
152
Replacing wiper blades
154
137
Rustproofing
Rustproofing - check and repair
Improving
Your Volvo received a very thorough and complete rustproofing at the
factory. Areas that are extremely vulnerable, such as the underbody,
have been sprayed with a thick, wear-resistant anti-corrosion compound
on the outside. Members, cavities and enclosed sections are sprayed
internally with a thin, penetrating rust inhibitor.
If you want to repair the rustproofing yourself, make sure the area is clean
and dry. Hose down, wash and dry the car thoroughly. Use a rustproofing
agent in a spray can or one that is intended for brush application.
The car’s rustproofing is maintained by doing the following:
a) thin (colourless), for visible places
b) thick, for areas prone to wear on the underbody and in the wheel
arches
· Keep the car clean! Wash chassis components*, the underbody,
and the inside and edges of wheel arches with a pressure washer.
When high pressure washing - hold the spray nozzle at least 30 cm
away from painted surfaces!
· Check and repair the rustproofing regularly.
* Trailing arms, link arms, spring mountings and spring strut seats.
The car’s rustproofing does not normally require treatment for approximately 8 years. After that time, it should be treated at three year intervals. If
your car requires treatment, consult your Volvo workshop.
Two types of rustproofing agent are available:
Possible repair areas with these agents:
· Visible welds and sheet metal joints - thin fluid
· Underbody and wheel arches - thick fluid
· Door hinges - thin fluid
· Bonnet hinges and catch - thin fluid
When you have finished treatment, excess rustproofer can be wiped off
using a rag dampened with white spirit.
Parts of the engine and suspension strut mountings in the engine bay
are treated at the works with a wax-based colourless rustproofing agent.
This withstands normal detergents without dissolving and losing its
rustproofing ability. On the other hand, if you wash the engine using
aromatic solvents such as turpentine or white spirit (especially those
which do not contain emulsifiers), the protective wax should be renewed
after washing. Your Volvo dealer has such waxes in stock.
138
Repairing paintwork damage
Paint
Paint is an important part of the car’s rustproofing and should therefore be checked regularly.
Repair paintwork damage immediately so that it
does not start to rust. The most common types
of paintwork damage that you can repair
yourself are:
· minor stone chips and scratches
· damage to wing edges and sills
When repairing paintwork, the car should
be clean and dry with a temperature above
+ 15 °C.
Colour code
Make sure you have the right colour.
The colour code number is on the data plate in
the engine compartment.
VOLVO CAR CORP.
MADE IN
SWEDEN
KG
KG
1.
KG
2.
KG
0300048A
Colour code
Minor stone chips and
scratches
Remove any paint residue with tape
Material:
· Primer in a can
· Paint in a can or a touch-up pen
· Brush
· Masking tape
· If the stone chip has not gone down to the
bare metal and an unpainted colour coat
remains, you can add paint immediately
after removing dirt.
Do as follows if the stone chip went down to
the bare metal:
· Fasten a piece of masking tape over the
damaged surface. Then remove the tape,
removing any paint residue (illustration 1).
· Stir the primer thoroughly and apply using
a fine brush or matchstick (illustration 2).
· When the primer is dry, apply the surface
coat with a brush.
· Ensure that the paint is well stirred and
apply several thin coats allowing it to dry
between coats.
· The procedure is the same for scratches, but
masking tape can be used to protect
undamaged paintwork (illustration 3).
· Wait a day or so and then finish the repair
by polishing. Use a soft rag and apply
lapping paste sparingly.
8100503A
Mask if necessary
139
Washing
Wash the car frequently!
Wash the car as soon as it becomes dirty, especially in the winter when
road salt and moisture can lead to corrosion.
Wash the car as follows:
· Thoroughly hose off the dirt on the car underbody (wheel arches,
wing edges, etc.).
· Rinse the entire car to remove loose dirt.
· When using high pressure hose:
Ensure that the high pressure hose nozzle does not come nearer
than 30 cm from the bodywork. Do not spray directly at the locks.
· Wash with a sponge using a lot of water with or without detergent.
· You can use lukewarm (maximum 35 °C) but not hot water.
· If the dirt is ingrained, you can wash the car with cold degreasing
agent, but then be sure that there is a drain separator where you are
washing the car. When using cold degreasing agent, ensure that the
car is not in direct sunlight or that the paint is warm from sunlight
or a warm engine. Sunlight and heat can cause permanent damage.
Consult your Volvo workshop.
· Dry the car with a clean, soft chamois.
· Clean the wiper blades with a lukewarm soap solution.
Suitable detergent:
Car shampoo.
Keep in mind the following:
Always wash off bird droppings from the paintwork as fast as
possible.
Bird droppings contain chemicals that affect and discolour paintwork
quickly. The discoloration cannot be polished off.
Exterior plastic parts
A special cleaning agent, available from Volvo dealers, is recommended
for cleaning exterior plastic parts. Never use strong stain removers.
140
WARNING!
After washing: always test the braking so that damp and corrosion do
not affect the brake pads and impair the brakes! Depress the brake pedal
lightly now and again when driving longer distances in the rain or slushy
snow to warm up and dry the brake discs and pads. You should also do
this when starting in very damp or cold weather conditions.
WARNING!
Do not wash the engine when it is still warm. Fire risk!
Washing
Automatic car wash
An automatic car wash is a simple and fast way of washing the car.
Remember that an automatic car wash can never replace a proper
handwash.
The brushes of an automatic car wash do not reach all areas.
During the first months of the car’s life it is recommended that you only
handwash the car.
Polishing and waxing
Polish and wax the car when you feel the paintwork is matte and when
you wish to give the paintwork extra protection, such as before winter.
The car does not usually need polishing until after one year. It can be
waxed earlier.
Wash and dry the car thoroughly before you begin polishing and/or
waxing. Clean away asphalt or tar splashes with Volvo asphalt remover
or white spirit.
Stubborn marks can be removed with fine rubbing paste for car paintwork. First polish and then wax with liquid or solid wax. Carefully
follow the instructions on the package. Many preparations contain both
polish and wax.
Do not wax or polish in direct sunlight.
Treating spots on leather upholstery
A special cleaning agent, available from Volvo dealers, is recommended
when cleaning leather upholstery. Treat the leather upholstery once or
twice a year using Volvo’s leather care kit. Never use strong solvents.
Such products may damage fabric, vinyl and leather upholstery.
Treating spots on interior plastic parts and surfaces
A special cleaning agent, available from Volvo dealers, is recommended
for cleaning interior plastic parts and surfaces. Do not scrape or rub spots.
Never use strong stain removers.
Cleaning seat belts
Use water and synthetic detergent. Special upholstery detergent is
available from your Volvo dealer. Make sure the seat belt is dry before
allowing it to retract.
Cleaning the interior
Treating spots on fabric upholstery
A special cleaning agent, available from Volvo dealers, is recommended
for cleaning the fabric upholstery. Other chemicals can impair the fire
retardant qualities of the upholstery.
IMPORTANT!
Sharp objects and Velcro may damage the textile upholstery.
141
Washing
Cleaning door mirrors and front side
windows with water-repellent coating (option)
Never use products such as car wax, degreaser or similar on mirror/glass
surfaces as this could ruin their water-repellent properties.
Take care when cleaning so as not to damage the glass surface.
To avoid damaging glass surfaces when removing ice, only use plastic ice
scrapers.
There is natural wear of the water-repellent coating.
NOTE! Treatment with a special finishing agent available from Volvo
dealers is recommended in order to maintain the water-repellent properties. This should be used first after three years and then each year.
142
Volvo Service
Volvo Service
Before the car left the factory, it was thoroughly test driven. It was
checked again in accordance with Volvo Car Corporation regulations
before it was handed over to you.
Volvo service programme
In order for you to keep your Volvo at the highest level of traffic safety,
driving safety and reliability you should follow the Volvo service
programme which is specified in the Warranty and Service schedule.
We advise you always to let a Volvo workshop carry out the servicing
and repair work. Your Volvo workshop has the personnel, the special
tools and the service literature which guarantees you the highest quality
of service. Your Volvo workshop always uses Volvo Genuine parts.
The Volvo Service schedule is developed for the normal motorist.
Important!
Recording vehicle data
One or more computers in your Volvo car can record detailed information.
This information is intended for research purposes in order to further
develop safety and to diagnose faults in certain systems. It can included
data such as seat belt usage by the driver and front passenger, information
on the function of different systems and modules in the car and information on the status of the engine, throttle control, steering, brake and other
systems.
This information can contain data on the driver’s driving style.
Such data can contain information including, but not limited to, vehicle
speed, use of the brake or accelerator pedal and steering wheel manoeuvres. The latter data can be stored for a limited time while the car is driven
and during the course of a collision or a near miss.
Volvo Car Corporation will not distribute this stored information without
permission. Volvo Car Corporation may, however, be forced to provide
this information if required by national legislation.
In general, Volvo Car Corporation and authorised workshops may read
and use the information.
For the Volvo warranty to apply, check and follow the instructions in
the Service and Warranty Manual.
Service or installation of accessories
Service or installation of accessories that affect the car’s electrical system
can only be carried out using electronic equipment specially developed
for the car. It is therefore important that you always contact your Volvo
workshop before beginning or carrying out service work that affects the
electrical system.
143
Volvo Service
WARNING!
The car ignition system has very high voltage!
The voltage in the ignition system is dangerous!
Do not touch spark plugs, ignition cables or the ignition coil when
the engine is running or the ignition is switched on!
The ignition should be switched off when:
· Conducting engine tests.
· Replacing parts in the ignition system, such as spark plugs,
ignition coil, distributor, ignition cables, etc.
Note the following before you begin
working on your car:
Battery
· Ensure that the battery cables are correctly connected and tightened.
· Never disconnect the battery when the engine is running (e.g. when
replacing the battery).
· Never use a fast charger to charge the battery. The battery cables
should be disconnected when recharging.
Environmental care
The battery contains acid that is both corrosive and poisonous.
It is important that the battery is handled in an environmentally friendly
way. Let your Volvo dealer assist you.
144
7700243d
Lifting the car
If the car is lifted with a workshop jack, it should sit with the front edge
on the engine support arm. Do not damage the splashguard under the
engine. Ensure that the jack is positioned so that the car cannot slide off
the jack. Always use axle stands or the like.
If you lift the car using a two pillar workshop lift, ensure that the front and
rear lift arms are fixed under the lifting points on the door sill.
See the illustration.
Bonnet, Engine compartment - left-hand drive
8
10
1
5
2b
2
Pull the handle..
4
3
1112
7
8200092d
6
9
2000305d
...press up and open
Opening the bonnet
Engine compartment
Pull the handle on the far left under the
dashboard. You hear when the lock releases.
Insert the hand in the centre of the front edge
of the bonnet and press up the safety catch
handle. Open the bonnet.
1
2
3
4
5
6
7
8
9
10
11
12
WARNING!
Check that the bonnet lock properly when
you close it!
Expansion tank, cooling system
Engine oil filler pipe
Engine oil dipstick
Clutch/brake fluid reservoir
Battery (in cargo compartment)
Data plate
Radiator
Power steering fluid reservoir
Air filter
Washer fluid reservoir
Main fuse box
Integrated relay/fuse box
WARNING!
Electric engine cooling fan:
Cooling fan may continue running and can
start itself after the engine is switched off!
145
Bonnet, Engine compartment - right-hand drive
8
5
1
4
10
2b
2
Pull the handle...
3
1112
7
6
9
8200095d
2000306d
..press up and open
Opening the bonnet
Engine compartment
Pull the handle on the far right under the
dashboard. You hear when the lock releases.
Insert the hand in the centre of the front edge of
the bonnet and press up the safety catch handle.
Open the bonnet.
1
2
3
4
5
6
7
8
9
10
11
12
WARNING!
Check that the bonnet locks properly
when you close it!
146
Expansion tank, cooling system
Engine oil filler pipe
Engine oil dipstick
Clutch/brake fluid reservoir
Battery (in cargo compartment)
Data plate
Radiator
Power steering fluid reservoir
Air filter
Washer fluid reservoir
Main fuse box
Integrated relay/fuse box
WARNING!
Electric engine cooling fan:
Cooling fan may continue running
and can start itself after the engine
is switched off!
Diesel
Fuel system
Draining condensation water from fuel filter
Only use diesel fuel from a well-known oil company that fulfils the
requirements for recommended fuel grade as described on page 164.
Never use diesel of doubtful quality. Special diesel fuel for winter use is
available from large oil companies. This fuel is less viscous at low
temperatures and reduces the risk of wax building up in the fuel system.
Keeping the tank well filled reduces the risk of condensation in the tank.
The fuel filter removes condensation, which could otherwise affect engine
function, from the fuel. The fuel filter should be drained as specified in the
Service and Warranty Book, and when you suspect that the car has been
filled with contaminated fuel.
During filling you should check that the area around the filler pipe is
clean. If you do the refuelling from a tank of your own, you should
filter the fuel.
Avoid spilling onto the paintwork. Wash off any spills with detergent
and water.
Empty tank
No special procedures are required if the tank runs dry. The fuel system
is bled automatically if the ignition switch is kept in position II for
approx. 60 seconds before the start attempt.
Important!
Diesel type fuels which must not be used:
special additives, Marine Diesel Fuel, fuel
oil, RME (Rape Methyl Ester), vegetable
oil.
These fuels do not fulfil the requirements
of Volvo’s recommendation and generate
increased wear and engine damage that is
not covered by the Volvo warranty.
147
Engine oil
Adverse driving conditions
Check the oil level more frequently for long
journeys:
· towing a caravan or trailer
· in mountainous regions
· at high speeds
· in temperatures colder than -30 °C or hotter
than +40 °C
· shorter driving distances (shorter than
10 km) at low temperatures (under 5 °C).
This may result in abnormally high oil
temperature or oil consumption.
2200315d
Checking and changing the
engine oil and oil filter
Important!
Always use oil of the prescribed grade, see
engine compartment decal.
Check the oil level frequently and change
the oil regularly.
The engine will be damaged if a lower than
specified grade of oil is used or if the car is
driven with the oil level too low.
Using oil of a higher grade is permitted. Volvo
recommends using an oil of a higher grade than
that specified on the decal for adverse driving
conditions. See page 161.
148
Change the oil and oil filter in accordance with
the intervals specified in the Service and
Warranty Booklet. When filling oil to top up a
low oil level, the oil being filled must be of the
same grade and viscosity as the oil in the
engine.
Checking the oil level in a new car is especially
important before the first scheduled oil change.
The Service and Warranty Booklet specifies the
odometer readings for oil changes.
Volvo recommends checking the oil level every
2500 km. The most accurate measurements are
made on a cold engine before starting. The
measurement will be inaccurate if taken
immediately after the engine is switched off.
The dipstick will indicate that the level is too
low because the oil has not had time to flow
down into the oil sump.
Engine oil
•
•
•
Wipe the dipstick clean before checking the
level.
Check the oil level using the dipstick. The
oil level must be between the MIN and
MAX marks.
If the level is close to the MIN mark, start
by topping up with 0.5 litres of oil. Top up
until the oil level is nearer the MAX than
the MIN mark on the dipstick. See 161-162
for volumes.
Important!
IMG-203460
The oil level must be within the area
marked on the dipstick.
Checking the oil in a cold engine:
• Wipe the dipstick clean before checking the
level.
• Check the oil level using the dipstick. The
oil level must be between the MIN and
MAX marks.
• If the level is close to the MIN mark, start
by topping up with 0.5 litres of oil. Top up
until the oil level is nearer the MAX than
the MIN mark on the dipstick. See page
161-162 for volumes.
Never fill above the MAX mark. Oil
consumption may increase if too much oil
is poured into the engine.
WARNING!
Do not spill oil onto the hot exhaust manifold
due to the risk of fire.
Checking the oil in a warm engine:
• Park the car on a level surface, switch off
the engine and wait 10-15 minutes to give
the oil time to run back down to the sump.
149
Coolant
Checking and topping up coolant
Follow the instructions on the packaging when topping up coolant.
It is important that the mixture of coolant concentrate and water is correct
for the prevailing weather conditions.Never top up with water only.
The risk of freezing increases with both too little and too much coolant
concentrate.
See capacities and recommended grade for fluids and oils on page 160.
Important!
Always use coolant with anti-corrosion agent as recommended by
Volvo.
New cars are filled with coolant that can withstand temperatures
down to approximately -35 °C.
Check the coolant regularly
The level should lie between the MIN and MAX marks on the
expansion tank.
Top up with fluid when the level has fallen to the MIN mark.
Important!
The engine must only be run with a well-filled cooling system.
High temperatures can occur, causing a risk of damage (cracks) to the
cylinder head.
WARNING!
The coolant may be very hot. If the coolant requires topping up
when the engine is at operating temperature, unscrew the expansion
tank cap slowly to gently release the overpressure.
150
Brake fluid, Power steering, Windscreen washer fluid
Clutch and brake fluid
reservoir
WARNING!
FULL
If the level of brake fluid in the reservoir is below the MIN mark, the car
should not be driven until the brake fluid has been topped up. The reason for
the loss of brake fluid must be investigated.
ADD
3601948d
5200678d
Washer fluid reservoir
Power steering fluid reservoir
Power steering fluid reservoir
Check the level at every service. It is not
necessary to change the fluid. The level should
lie between the ADD and FULL marks.
See capacities and recommended grade for
fluids and oils on page 160.
NOTE! If a fault occurs in the power steering
(or if the car has no power and is to be towed)
the car can still be steered. Remember that the
steering will be much heavier than normal and
more strength is required to turn the steering
wheel.
Clutch and brake fluid reservoir
The brake and clutch fluid have a common
reservoir1. The fluid level must be between the
MIN and MAX marks. Check the level
regularly. Change the brake fluid every other
year or at every other regular service.
See capacities and recommended grade for
fluids and oils on page 160.
NOTE! The fluid should be changed annually
on cars which drive in conditions requiring
hard and frequent braking, driving in mountains
or tropical climates with high humidity.
Washer fluid reservoir
The wipers for the windscreen and headlamps
share the same fluid reservoir.See capacities and
recommended grade for fluids and oils on
page 160.
Use washer fluid during the winter so that the
fluid does not freeze in the pump, reservoir
and hoses.
Tip: clean the wiper blades when topping up
washer fluid.
1
Location dependent on whether car is left or
right-hand drive.
151
Battery care
A
· Check all battery cells. Use a screwdriver to
remove the caps. Each cell has its own maximum level mark.
· If necessary, top up with distilled water to
the battery’s maximum mark.
· Never fill above the maximum mark (A).
Important!
Always use distilled or deionised water
(battery).
· Tighten the caps properly.
NOTE! The life of the battery is shortened if it
becomes discharged repeatedly.
3100063d
Battery care
The service life and function of the battery is
influenced by factors such as the number of
starts, discharging, driving style, driving
conditions and climatic conditions.
Repeated use of the parking heater and other
great power consumers in combination with
short trips can lead to battery discharge and
thereby difficulty starting.
For the battery to function satisfactorily,
consider the following:
· Regularly check that the battery fluid level
is correct (A).
152
Symbols:
Use protective goggles.
Further information in the
owner’s manual.
Store the battery out of the
reach of children.
WARNING!
Batteries can generate oxyhydrogen gas,
which is highly explosive.
One spark, which can be generated if you
connect the jump leads incorrectly, is sufficient to make the battery explode.
The battery contains sulphuric acid, which
can cause serious burns.
If the acid comes into contact with eyes,
skin or clothing, flush with large quantities of water.
If acid splashes into the eyes, seek medical
attention immediately.
The battery contains
corrosive acid.
Avoid sparks and open
flames.
Risk of explosion.
Battery care
Replacing the battery
A
B
3100181m
A. Battery without cover
B. Battery with cover
Removing the battery:
· Switch off the ignition and remove the key.
· Wait at least 5 minutes before touching any
electrical terminals. This allows time for the
information in the car’s electrical system to
be stored in the control modules.
· Undo the screws from the lock brace over
the battery and remove the brace.
· Bend up the plastic cover over the negative
battery terminal or unscrew the cover from
the battery.
· Disconnect the negative battery cable.
· Detach the lower console holding the
battery.
· Bend aside the plastic cover and disconnect
the positive cable.
· Remove the battery.
WARNING!
Batteries can generate oxyhydrogen gas,
which is very dangerous. One spark,
which can be generated if you connect
the jump leads incorrectly, is sufficient to
make the battery explode. The battery
contains sulphuric acid, which can cause
serious burns. If the acid comes into
contact with eyes, skin or clothing, flush
with large quantities of water. If acid
splashes into the eyes, seek medical
attention immediately.
Fitting the battery:
· Position the lower console and screw it in
place.
· Position the lower console and screw it in
place.
· Connect the positive cable, press in and fold
· Connect the negative cable, fold down the
plastic cover.
· Fit the plastic cover or the cover over the
battery.
· Make sure the evacuation hose is correctly
connected to both the battery and the outlet
in the bodywork.
· Fit the lock brace over the battery and
tighten the screws.
153
Replacing wiper blades
3603056d
Replacing windscreen wiper
blades
•
•
•
Fold out the wiper arm and hold the wiper
blade.
Push in the ribbed locking springs on the
wiper blade while lifting it from the arm extension.
Install the new blade following the instructions in reverse order and check that the
blade is properly secured.
NOTE! Keep in mind that the wiper blade on
the driver's side is longer than the blade on the
passenger side.
154
Specifications
Type designation
156
Dimensions and weights
157
Engine specifications
158
Capacities
160
Fuel
163
Catalytic converter and suspension
165
Electrical system
166
155
Specifications
Type designation
Whenever contacting your Volvo dealer and
when ordering spare parts and accessories for
your car, it makes things easier if you know
your car’s type designation, vehicle
identification number and engine number.
1. Decal for parking heater.
2. Type and model year designation, and
vehicle identification number.
3. Engine type designation, component and
serial number.
4. Engine oil decal* specifies oil grade and
viscosity.
5. Gearbox type designation and serial
number
a: Manual gearbox
b: Automatic gearbox AW.
6. Type designation, vehicle identification
number, maximum permissible weights, codes
for colour and upholstery and type approval
number.
HFGDOIHV
HFGJJFFOI
BFDRYOIHV
Gfdr urtvb
Seyj tu
Seyj tu
Fkfu
Fkfu
Ohtk jdtr
Mgdh ytegf
Ehdfjljl ncy
YV1LS5502N2000327
B5254S
1234567
0300387d
P1208632
M56L
AISIN
AW CO
LTD
VOLVOCARCORP.
INJAPAN
MADE
50-42LE
SERIALNO
T100001
* Certain engine variants
156
KG
3,77
KG
1.
KG
2.
KG
MADEIN
SWEDEN
Dimensions and weights
Weights
Measurements
Length ................................................................
Width .................................................................
Height ................................................................
Wheelbase ..........................................................
Front track .........................................................
Rear track ...........................................................
482 cm
183 cm
145 cm
279 cm
158 cm
156 cm
The kerb weight includes the driver, the fuel tank 90% full and all fluids.
The weight of passengers and accessories, such as a towbar, towball load
(when a trailer is hitched, see table), load carriers, and roof box, affect
load capacity and must not be included in the kerb weight.
Permitted weight (in addition to driver) = Gross vehicle weight - Kerb
weight. For the location of the decal, see page 156.
1. Max. total weight
VOLVO CAR CORP.
MADE IN
SWEDEN
2. Max. train weight (car+trailer)
3. Max. front axle load
4. Max rear axle load
Max load:
Max roof load:
Maximum trailer weight:
KG
KG
1.
KG
2.
KG
1
2
3
4
0300047A
see registration papers
100 kg
1800 kg
Warning!
The driving characteristics of the car change depending on how
heavily it is loaded and how the load is distributed.
157
Engine specifications
2.0T
BIFUEL
CNG
2.4
2.4
B5204T5
B5244SG
B5244S
B5244S2
(kW/rps)
AWD
132/92
-
103/97
-
125/98
-
103/75
-
154/83
-
162/83
-
(hp/rpm)
AWD
180/5500
-
140/5800
-
170/6000
-
140/4500
-
210/5000
-
220/5000
-
(Nm/rps)
AWD
240/30-83
-
192/75
-
225/75
-
220/55
-
320/25-75
-
285/33-83
-
23.0/4500
-
22.5/3300
-
32.6/1500-4500 35.7/2100-4000
-
Engine variant
Output*
Torque*
(kpm/rpm) 24.5/1850-5000 19.6/4500
AWD
-
2.5T
B5254T2
2.4T
B5244T4a
No. of cylinders
5
5
5
5
5
5
Bore (mm)
81
83
83
83
83
83
77
90
90
90
93,2
90
Cylinder displacement (dm (l)) 1.98
2.44
2.44
2.44
2.52
2.44
Compression ratio
9.5:1
10.3:1
10.3:1
10.3:1
9.0:1
8.5:1
Electrode gap (mm)
0.7
1.2
1.2
1.2
0.7
0.7
Tightening torque (Nm)
28
30
30
30
30
28
Stroke (mm)
3
Spark plugs:
To verify the type of engine in the car - see the type designation stamped into the engine compartment (Type designations - page 156, point 3).
a
*
158
Thailand, Malaysia
Output and torque as per test standard EU 80/1269. For petrol engines, 98 octane is always used for this test.
Engine specifications
T6
Engine variant
2.9
D5
2.4D
B6294T
B6294S2
D5244T
D5244T2
(kW/rps)
AWD
200/87
-
144/87
-
120/67
-
96/67
-
(hp/rpm)
AWD
272/5200
-
196/5200
-
163/4000
-
130/4000
-
(Nm/rps)
AWD
380/30-83
-
280/65
-
340/29-50
-
280/29-50
-
(kpm/rpm)
AWD
38.8/1800-5000 28.6/3900
-
34.7/1750-3000 28.6/1750-3000
-
No. of cylinders
6
6
5
5
Bore (mm)
83
83
81
81
90
90
93.2
93.2
Cylinder displacement (dm (l))
2.92
2.92
2.40
2.40
Compression ratio
8.5:1
10.3:1
18.0:1
18.0:1
Electrode gap (mm)
0.7
3x1.2
-
-
Tightening torque (Nm)
30
25
-
-
Output*
Torque
Stroke (mm)
3
Spark plugs:
To verify the type of engine in the car - see the type designation stamped into the engine compartment (Type designations - page 156, point 3).
* Output and torque as per test standard EU 80/1269. For petrol engines, 98 octane is always used for this test.
159
Capacities
Other fluids and lubricants
Fluid
Transmission fluid
Coolant
Air conditioning
Brake fluid
Power steering
System
Manual, 5-speed (M56/M58)
Manual, 6-speed (M66)
Automatic gearbox (AW55-51)
Automatic gearbox (GM4T65)
2
160
Recommended grade
Transmission fluid1: MTF 97309
Transmission fluid1: JWS 3309
Transmission fluid1 Dexron III G
Petrol engines without turbo
Petrol engines with turbo
Diesel engines
Compressor oil
8.0 litres
9.0 litres
12.5 litres
180-200 gram2
Refrigerant
500-600 gram2 R134a (HFC134a)
0.6 litres
DOT 4+
0.9 litres
Power steering fluid: WSS M2C204-A or equivalent product with
0.2 litres
specifications.
4.5 litres
Use a washer anti-freeze recommended by Volvo mixed with water
6.4 litres
at temperatures below freezing.
For tank volume, see Fuel section on page 163.
System:
same of which reservoir
Washer fluid reservoir Variant with headlamp wipers
high pressure wash
Fuel tank
1
Volume
2.1 litres
2.0 litres
7.2 litres
12.7 litres
Coolant with corrosion protection mixed with water, see packaging.
The thermostat starts opening at 90 ºC in petrol engines and at 82 ºC
diesel engines.
PAG
The recommended transmission fluid must be used to prevent damage to the gearbox. Do not mix with any other transmission fluid. If the
transmission is topped up with a different fluid, contact an authorised Volvo workshop for servicing.
Weights can vary depending on the engine variant. Contact an authorised Volvo workshop for the exact information.
Capacities
Engine oil
Adverse driving conditions
Check the oil level more frequently for long
journeys:
· towing a caravan or trailer
· in mountainous regions
· at high speeds
· in temperatures colder than -30 °C or hotter
than +40 °C.
· shorter driving distances (shorter than
10 km) at low temperatures (under 5 °C)
This may result in abnormally high oil
temperature or oil consumption.
Choose a fully synthetic engine oil for adverse
driving conditions. It provides extra protection
for the engine.
Volvo recommends
oil products.
Important!
Always use the prescribed oil grade and
viscosity.
If an oil other than that prescribed has been
used, contact the local authorised Volvo
workshop immediately for service.
Do not use extra oil additives. They could
damage the engine.
2200293v
Viscosity chart
161
Capacities
Engine oil
Oil decal
Engine variant
2.0T
2.4
2.4
2.4T
2.5T
1
2
B5204T5
B5244S
B5244S2
B5244T42
B5254T2
The following applies when the abovementioned decal is fitted in the car’s engine
compartment. For location, see page 156
Oil grade: ACEA A5/B5
Viscosity: SAE 0W-30
Volume between
MIN y MAX
1.2
Oil decal
Volume1/ litre
Engine variant
5.5
1
Volume1/ litre
BIFUEL B5244SG
1.2
5.5
1.5
6.6
B6294T
B6294S2
Including filter change
Oil decal
Engine variant
162
Volume between
MIN y MAX
T6
2.9
Including filter change
Thailand, Malaysia
1
The following applies when the abovementioned decal is fitted in the car’s engine
compartment. For location, see page 156
Oil grade: ACEA A1/B1
Viscosity: SAE 5W-30
When driving under adverse conditions, use
ACEA A5/B5 SAE 0W-30.
2.4D
D5244T2
D5
D5244T
Including filter change
The following applies when the abovementioned decal is fitted in the car’s engine
compartment. For location, see page 156
Oil grade: ACEA A3/B3/B4
Viscosity: SAE 5W-30
Volume between
MIN y MAX
2.0
Volume1/ litre
6.5
Fuel
Fuel consumption, emissions and volume
Engine variant
Gearbox
2.4
B5244S2
2.4
B5244S
Manual 5-speed (M56)
Automatic gearbox (AW55-51)
Manual 5-speed (M56)
Automatic gearbox (AW55-51)
Manual 5-speed (M56)
Automatic gearbox (AW55-51)
Manual 5-speed (M56)
Automatic gearbox (AW55-51)
Automatic gearbox (AW55-51)
Manual 5-speed (M56)
Automatic gearbox (AW55-50)
Manual 5-speed (M56)
Automatic gearbox (AW55-50)
Manual 5-speed (M56)
Automatic gearbox (AW55-50)
Geartronic
4-speed (GM4T65)
Geartronic
10.6
4-speed (GM4T65)
Automatic gearbox (AW55-51) -
2.0T B5204T5
2.5T B5254T2
2.4
AWD
B5244SG Bi-Fuel
D5
D5244T
2.4D D5244T2
T6
B6294T
2.9
B6294S2
2.4T B5244T42
Consumption
(litres/100 km)1
8.9
9.6
9.0
9.7
9.0
9.8
9.2
10.0
10.5
9.2
9.9
6.5
7.7
6.5
7.7
11.1
Carbon dioxide
emissions (g/km)
212
229
214
232
214
234
219
239
252
220
242
172
204
171
204
268
Tank volume
(litres)
70
70
80
80
72
30 3
70
70
70
80
255
80
-
70
Emission values are affected by fuel quality and may therefore differ from those specified if fuel of a different standard than that
recommended by Volvo is used.
2
Certain countries.
3
Fuel tank.
1
163
Fuel
Specified fuel consumption
Official fuel consumption figures are based on
a standard driving cycle in accordance with EU
Directive 80/1268 comb.
Fuel consumption figures may be altered if the
car is equipped with extra equipment that
affects the car’s weight. The manner in which
the car is driven and other non-technical factors
can also affect fuel consumption.
Consumption is higher and power output lower
when driving using fuel with an octane rating
of 91 RON.
Recommended fuel grade
Petrol
The engine can be run with octane ratings of
91, 95 and 98 RON.
When driving in temperatures above +38 ºC,
use of fuel with the highest possible octane
rating is recommended for optimum performance and fuel economy.
· 98 RON is recommended for maximum
effect and minimum fuel consumption.
· 95 RON can be used for normal driving.
· 91 RON must not be used in 4-cylinder
engines and, in general, should only be used
as an exception. However, the engine will
not be damaged by this fuel grade.
Petrol: Standard EN 228
Important!
Refuel with correct petrol!
Your car has a catalytic converter. Only drive
with unleaded petrol so as not to damage the
catalytic converter.
164
Diesel
Diesel: Standard EN 590
JIS K2204 or similar
Important!
Diesel fuels not to be used: special additives,
Marine Diesel Fuel, fuel oil, RME (Rape
Methyl Ester), vegetable oil.
These fuels do not fulfil the requirements of
EM 590 and generate increased wear and
engine damage that is not covered by the
Volvo warranty.
Catalytic converter and suspension
TM
2501523d
Lambda-sond Heated oxygen sensor
The lambda sensor is part of a management
system intended to reduce emissions and
improve fuel economy.
An oxygen sensor monitors the oxygen content
of the exhaust gases leaving the engine. These
values are fed into an electronic system that
continuously controls the injectors. The ratio of
air to fuel is continuously adjusted.
These adjustments create optimal conditions for
efficient combustion, and together with the threeway catalytic converter reduce harmful emissions (hydrocarbons, carbon monoxide and
nitrous oxides).
Wheel suspension, springing
Front end
McPherson type spring strut. Unitary construction of shock absorbers and spring. Rack and
pinion steering. Safety type steering shaft. The
values apply to an unladen car with full tank,
coolant and spare wheel.
Rear suspension
Independent suspension with individually
sprung wheels with shock absorbers. The
suspension consists of rear-facing trailer arms,
upper and lower control arms, track rods and
anti-roll bar.
Catalytic converter
The purpose of the catalytic converter is to
purify exhaust.
It is located in the exhaust flow near the engine
to quickly reach operating temperature.
The catalytic converter consists of a monolith
(ceramic or metal) with channels. The channel
walls are coated with a thin layer of platinum,
rhodium and palladium. The metals act as
catalysts, i.e. they accelerate the chemical
process without being used up themselves.
165
Electrical system
General
12-volt system with voltage regulated alternating current generator. Single pole system in
which the chassis and engine block are used as
conductors.The negative pole is connected to
the chassis. The car is equipped with an extra
ground lead to reduce the magnetic fields.
1
2
3
4
5
Battery
Voltage
12 V 12 V 12V
Cold start capacity
520 A 600 A 800 A*
(CCA)
Reserve capacity (RC) 100
120 170
min
min min
* Cars equipped with diesel and parking heater.
If the battery is changed, replace it with a
battery of the same cold start capacity and
reserve capacity as the original
(see the decal on the battery).
Generator max current
Starter motor, power
166
140 A
1,4/1,7/2,2 kW
6
7
8
9
10 11
3501808d
Bulbs
Bulbs
1. Main beam /
dipped beam
2. Bi-Xenon
3. Front fog lamp
4. Parking lamp (front),
side marker lamp
(rear)
4. Side marker lamp
(front)*
5. Direction
indicator (front)
6. Direction
indicator (side)
7. Reversing lamp,
direction indicator
(rear)
8. Rear fog lamp,
parking lamp (rear)
Type (LL) Socket
H7 55W
D2R35W
H1 55W
W5W
W2.1x9.5d
W3W
W2.1x9.5d
Bulbs
9. Rear parking lamp
10. Numberplate
lighting, courtesy
lighting (front) cargo
compartment lighting
11. Vanity mirror
4. Courtesy lighting
(rear)
Type (LL) Socket
R5W
BA15s
C5W
1.2W
SV8.5
SV5.5
W5W
W2.1x9.5d
PY21W BAU 15s
WY5W
W2.1x9.5d
P21W
BA15s
P21/4W BAZ15d
*S80 Graphite Edition (white lens): WY5W
(yellow lamp), W2.1x9.5d.
Audio
Overview, Stereo HU-450
168
Overview, Stereo HU-650
169
Overview, Stereo HU-850
170
Audio functions
171
Radio functions
173
Cassette player
180
CD player
181
Dolby Surround Pro Logic II
184
Technical data - Audio
186
167
Stereo HU-450
HU-450
3905005d
1. POWER (Off/On) - Press Volume Turn
2. PRESET/ CD PUSH MENU Stored radio stations
CD changer (option)
3. SOURCE PUSH MENU Open the main menu Press Turn to select: Radio FM, AM Cassette
CD changer (option)
4. FADER - Press out and turn
BALANCE - Press out, pull and turn
5. SCAN - Automatic station search
6. EXIT - Scroll back in the menu
168
7. Navigation buttons CD/radio - seek/change station or
track Cassette - Fast forward/rewind,
select next/previous track
8. Display
9. FM - Shortcut
10. AM - Shortcut
11. TAPE - Shortcut
12. AUTO - Automatic preset of radio stations
13. BASS - Press out and turn
TREBLE - Press out, pull and turn
14. Cassette - Direction select
CD changer
(option) - Random
15. Cassette opening
16. Cassette opening
Stereo HU-650
COMPACT
DIGITALAUDIO
HU-650
3905004d
1.
2.
3.
4.
5.
6.
7.
POWER (Off/On) - PressVolume - Turn
PRESET/ CD PUSH MENU Stored radio stations
CD changer (option)
SOURCE PUSH MENU - Open the
main menu - Press Turn to select:
Radio - FM, AM
Cassette
CD
CD changer (option)
FADER - Press out and turn
BALANCE - Press out, pull and turn
EXIT - Scroll back in the menu
SCAN - Automatic station search
Navigation buttons - seek/change
station or track
8.
9.
10.
11.
12.
13.
14.
15.
CD eject
CD slot
CD random
FM - Shortcut
AM - Shortcut
CD - Shortcut
AUTO - Automatic preset of radiostations
BASS - Press out and turn
TREBLE - Press out, pull and turn
16. Cassette - Direction select
CD changer (option) - Random
17. Cassette opening
18. Cassette eject
169
Stereo HU-850
COMPACT
DIGITALAUDIO
HU-850
3905006d
1.
2.
3.
4.
5.
POWER (Off/On) - Press
VOLUME - Turn
BASS - Press out and turn
TREBLE - Press out, pull and turn
FADER - Press out and turn
BALANCE - Press out, pull and turn
Centre volume - Press out and turn
Output level - Press out, pull and turn
PRESET/ CD PUSH MENU Stored radio stations
CD changer (option)
6.
7.
8.
9.
SOURCE PUSH MENU Open the main menu - Press
Turn to select:
Radio - FM, AM
CD
CD changer (option)
EXIT - Scroll back in the menu
SCAN - Automatic station search
Navigation buttons - seek/change station
or track
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
170
CD eject
Dolby Pro Logic II
2-channel stereo
3-channel stereo
CD slot
CD random
AM - Shortcut
FM - Shortcut
CD - Shortcut
AUTO - Automatic preset of radio
stations
Display
Audio functions HU-450/650/850
3901856d
3902418d
On/Off switch
Press button to switch the radio on or off.
Volume control
Turn the knob clockwise to increase volume.
Volume control is electronic and does not have
an end stop. If you have a keypad in the
steering wheel, increase or decrease volume
with the + or - buttons.
Volume control - TP/PTY/
NEWS
If a cassette or a CD is playing when the radio
receives traffic information, news, or a selected
programme type, the function is interrupted,
and the message will be heard
at the pre-set volume for traffic information,
news or programme type. Volume is adjusted
with the volume control.
The unit will thereafter return to the previously
set volume and continue playing the cassette or
the CD.
Bass
Set the bass by pressing out the button and
turning to right or left. In the centre position the
volume is “normalised”. Press the button back
to original position after setting.
Treble
Set the treble by pressing out the button, pull it
further out and turn it left or right. In the centre
position the volume is “normalised”. Press the
button back to original position after setting.
171
Audio functions HU-450/650/850
3901858d
3905008m
3905009m
3905063m
Fader – Balance front/rear
Balance – Balance right/left
Selection of sound source
Set a suitable balance between the front and rear
loudspeakers by pressing out the button and
then turning it to the right (sound to front) or to
the left (sound to the rear). Centre position
means that the balance is “normalised”. Press
the button back to its original position after
setting.
Set the balance by pressing, pulling out the
button and turning to right or left. In the centre
position the volume is “normalised”. Press the
button back to its original position after setting.
There are two ways to select sound source:
172
Either with the shortcut keys (AM, FM
CD (HU-650/850), TAPE (HU-450)) or with
the SOURCE knob.
Turn the SOURCE knob to select FM or AM.
This knob can also be used to select
cassette (HU-450/650), CD (HU-650/850) or
CD changer (option) if connected.
The selected sound source is shown in the
display.
Radio functions HU-450/650/850
3905010m
3901873d
Scanning
Station search
Steering wheel keypad
Press the SCAN button to start the search.
When the radio finds a station, it stops scanning
for a 10 seconds. It then resumes scanning.
To listen to the station, press the SCAN or
EXIT button.
Press or
to seek lower or higher
frequencies. The radio searches for the next
audible station and then stops.
Press the button again to continue the search.
If you have a keypad in the steering wheel,
press the right or left arrow to select preset
stations.
NOTE! If the car is equipped with an
integrated telephone, the steering wheel
keypad can only be used for telephone
functions when the telephone is activated.
When in active mode, telephone information
is always shown in the display. Deactivate
.
the telephone by pressing
Switch off the telephone if you do not have an
SIM card. See page 190.
Manual tuning
Press and hold
or . MAN is shown on the
display. The radio slowly scrolls in the desired
direction, increasing its tempo after a few
seconds. Release the button when the desired
frequency shows in the display.
The frequency can then be adjusted by briefly
pressing one of the arrow keys or .
Manual adjustment mode stays in effect five
seconds after the last press.
173
Radio functions HU-450/650/850
3905007d
3905009m
3901873d
Programming stations
Autostoring stations
1. Set the desired frequency.
2. Briefly press the PRESET/CD knob.
Select a number by turning forwards or
backwards. Press again to store the desired
frequency and station.
This function automatically seeks and stores up
to 10 strong AM or FM stations in a separate
memory. The function is especially useful in
areas in which you are unfamiliar with the radio
stations or their frequencies.
Preset
1. Select radio mode using the AM or FM
button.
2. Start the search by pressing and holding
AUTO (more than 2 seconds).
3 AUTO is shown on the display and a
number of strong stations (max. 10) from
the set frequency band are saved in the
autostore memory.
If there are no stations with sufficient signal
strength, NO STATION is displayed.
To select a preset radio programme, turn the
PRESET/CD to the stored number. The set
programme is displayed.
174
4. Briefly press the AUTO button or one of
the arrows of the steering wheel keypad to
scroll to another of the automatically preset
stations.
AUTO is shown on the display when the radio
is in autostore mode.
The text disappears when you return to
ordinary radio mode.
Return to ordinary radio mode by pressing
FM, AM or EXIT or by turning the
PRESET/CD-knob.
Returning to autostore mode:
Briefly press AUTO.
Radio functions HU-450/650/850
Radio Data System - RDS
RDS is a system that links specific network
transmitters. It is used, for example, to tune the
correct frequency of a station irrespective of the
transmitter or the active sound source
(e.g. CD). The system can also be used for
receiving traffic information and for finding
broadcasts of a specific type.
Radio text is also a component of RDS. A radio
station can transmit information about the radio
programme currently being broadcast.
Some radio stations do not use RDS or only
use a limited range of its features.
PI search (automatic station
search)
When listening to an RDS transmitter, various
information, such as traffic information, is
stored in the radio.
When a preset RDS transmitter is later selected,
the radio updates the transmitter’s RDS
information. If the radio is at the boundary or
just outside of the transmitter’s range, the radio
automatically seeks the strongest possible
transmitter of that channel.
If there is no audible transmitter, the radio
quiets and the PI SEEK appears on the display
until the station is found.
Traffic information - TP
Station
Traffic information from RDS stations
interrupts other sound sources. The message is
heard at the volume set for this specific feature.
As soon as the message ends, the audio system
returns to the previous sound source and
volume setting.
Activating traffic information:
1. Select radio mode using the FM button and
press SOURCE.
2. Select TP and press SOURCE.
3. Turn SOURCE, select TP ON (flashing
text) and press SOURCE.
4. Press EXIT.
Deactivating TP
1. Select radio mode using the FM button and
press SOURCE.
2. Select TP and press SOURCE.
3. Turn SOURCE, select TP OFF (flashing
text) and press SOURCE.
4. Press EXIT.
TP is shown on the display when the function
is activated.
Press EXIT if you do not wish to listen to a
traffic bulletin.
The TP function remains active and the radio
waits for the next traffic bulletin.
Activate traffic information from a special
channel:
1. Select radio mode using the FM button.
2. Activate the station from which traffic
information is to be received.
3. Press SOURCE.
4. Turn SOURCE, select ADVANCED
MENU and press SOURCE.
5. Turn SOURCE, select RADIO SETTINGS
and press SOURCE.
6. Turn SOURCE, select TP STATION and
press SOURCE.
7. Turn SOURCE, select SET CURRENT and
press SOURCE.
8. Press EXIT.
Deactivating TP Station
1. Select radio mode using the FM button and
press SOURCE.
2. Turn SOURCE, select ADVANCED
MENU and press SOURCE.
3. Turn SOURCE, select RADIO SETTINGS
and press SOURCE.
4. Turn SOURCE, select TP STATION and
press SOURCE.
5. Turn SOURCE, select TP STATION OFF
and press SOURCE.
6. Press EXIT.
175
Radio functions HU-450/650/850
TP search
This function allows you to listen to traffic
information when travelling between different
areas and countries without selecting a station.
1. Select radio mode using the FM button and
press SOURCE.
2. Turn SOURCE, select ADVANCED
MENU and press SOURCE.
3. Turn SOURCE, select RADIO SETTINGS
and press SOURCE.
4. Turn SOURCE, select TP SEARCH and
press SOURCE.
5. Turn SOURCE, select TP SEARCH ON or
TP SEARCH OFF (flashing text) and press
SOURCE.
6. Press EXIT.
News
Messages with a programme code (such as
news from RDS stations) will interrupt other
sound sources at the volume set for this specific
feature. As soon as the news broadcast is
finished, the audio system returns to the
previous sound source and volume setting.
176
Activating News:
1. Select radio mode using the FM button and
press SOURCE.
2. Turn SOURCE, select NEWS and press
SOURCE.
3. Turn SOURCE, select NEWS ON (flashing
text) and press SOURCE.
4. Press EXIT.
NEWS appears on the display.
To deactivate News:
1. Select radio mode using the FM button and
press SOURCE.
2. Turn SOURCE, select NEWS and press
SOURCE.
3. Turn SOURCE, select NEWS OFF
(flashing text) and press SOURCE.
4. Press EXIT.
NEWS disappears from the display.
Press EXIT if you do not wish to listen to a
news broadcast.
The News function remains active and the radio
waits for the next news programme.
Setting the current station as news source:
1. Select radio mode using the FM button.
2. Activate the station from which traffic
information is to be received.
3. Press SOURCE.
4. Turn SOURCE, select ADVANCED
MENU and press SOURCE.
5. Turn SOURCE, select RADIO SETTINGS
and press SOURCE.
6. Turn SOURCE, select NEWS STATION
and press SOURCE.
7. Turn SOURCE, select SET CURRENT and
press SOURCE.
8. Press EXIT.
To deactivate News Station:
1. Select radio mode using the FM button and
press SOURCE.
2. Turn SOURCE, select ADVANCED
MENU and press SOURCE.
3. Turn SOURCE, select RADIO SETTINGS
and press SOURCE.
4. Turn SOURCE, select NEWS STATION
and press SOURCE.
5. Turn SOURCE, select NEWS STN OFF
and press SOURCE.
6. Press EXIT.
Radio functions HU-450/650/850
Programme types
Displayed
Programme type - PTY
PTY standby
OFF
New features
Current affairs
Information
Sport
Education
Theatre
Culture and Art
Science
Entertainment
Pop music
Rock music
Easy listening
Light classical
Classical music
Other music
Weather
Economy
For children
Social questions
Spiritual questions
Telephone watch
Travel and holiday
Leisure and hobby
Jazz music
Country music
National music
Golden oldies
Folk music
Documentary
PTY OFF
News
Current
Info
Sport
Educ
Theater
Culture
Science
Enterta
Pop
Rock
Easy list
L Class
Classical
Other M
Weather
Economy
For children
Social
Spiritual
Telephone
Travel
Leisure
Jazz
Country
Nation M
“Oldies”
Folk
Document
Use the PTY function to select between the
various programme types
1. Select radio mode using the FM button and
press SOURCE.
2. Turn SOURCE, select PTY and press
SOURCE.
3. Turn SOURCE, select PTY in the menu and
press SOURCE.
4. The radio begins searching for the selected
programme type.
5. If you do not wish to listen to the station
found by the radio, continue the search
using the left or right arrow key.
6. If the radio does not find a station with the
selected programme type, it returns to the
previous frequency.
Not all radio stations have a PTY designation
PTY mode is then in standby until the selected
programme type is broadcast. When this
happens, the radio automatically switches to the
station broadcasting the selected programme
type.
Deactivating:
1. Select radio mode using the FM button and
press SOURCE.
2. Turn SOURCE, select PTY and press
SOURCE.
3. Turn SOURCE, select PTY OFF and press
SOURCE.
4. Press EXIT.
The PTY symbol disappears from the display
and the radio resumes normal mode.
PTY - language
The PTY function can be used to select the
language used in the radio display (English,
German, French or Swedish).
1. Select radio mode using the FM button and
press SOURCE.
2. Turn SOURCE, select ADVANCED
MENU and press SOURCE.
3. Turn SOURCE, select RADIO SETTINGS
and press SOURCE.
4. Turn SOURCE, select PTY LANGUAGE
and press SOURCE.
5. Turn SOURCE, select language and press
SOURCE.
6. Press EXIT.
177
Radio functions HU-450/650/850
Automatic frequency
updating
The AF function is normally activate and
ensures that the radio tunes to the strongest
available transmitter.
Activating AF:
1. Select radio mode using the FM button and
press SOURCE.
2. Turn SOURCE, select ADVANCED
MENU and press SOURCE.
3. Turn SOURCE, select RADIO SETTINGS
MENU and press SOURCE.
4. Turn SOURCE, select AF ON (flashing
text) and press SOURCE.
5. Press EXIT.
Deactivating AF:
1. Select radio mode using the FM button and
press SOURCE.
2. Turn SOURCE, select ADVANCED
MENU and press SOURCE.
3. Turn SOURCE, select RADIO SETTINGS
MENU and press SOURCE.
4. Turn SOURCE, select AF OFF (flashing
text) and press SOURCE.
5. Press EXIT.
178
Regional radio programmes
The regional function is normally deactivated.
When the function is activated you can continue
listening to a regional broadcast even if the
signal is weak.
Activating REG:
1. Select radio mode using the FM button and
press SOURCE.
2. Turn SOURCE, select ADVANCED
MENU and press SOURCE.
3. Turn SOURCE, select RADIO SETTINGS
MENU and press SOURCE.
4. Turn SOURCE, select REG LOCK
(flashing text) and press SOURCE.
5.Press EXIT.
REG appears on the display.
Deactivating REG:
1. Select radio mode using the FM button and
press SOURCE.
2. Turn SOURCE, select ADVANCED
MENU and press SOURCE.
3. Turn SOURCE, select RADIO SETTINGS
MENU and press SOURCE.
4. Turn SOURCE, select REG SWITCH
(flashing text) and press SOURCE
5. Press EXIT.
EON - Local/Distant
(Enhanced Other Networks)
When EON is activated, the radio programme is
interrupted for traffic bulletins, news broadcasts
or the like from other channels.
The function has two levels:
Local - only interrupts if the signal is
strong.
Distant - also interrupts with weaker
signals.
1. Select radio mode using the FM button and
press SOURCE.
2. Turn SOURCE, select ADVANCED
MENU and press SOURCE.
3. Turn SOURCE, select RADIO SETTINGS
MENU and press SOURCE.
4. Turn SOURCE, select EON (flashing text)
and press SOURCE.
5. Turn SOURCE, select Local or Distant and
press SOURCE.
6. Press EXIT.
Radio functions HU-450/650/850
Resetting RDS functions
Radio text
Resets all radio settings to the original factory
settings.
1. Select radio mode using the FM button and
press SOURCE.
2. Turn SOURCE, select ADVANCED
MENU and press SOURCE.
3. Turn SOURCE, select RESET TO DEFAULT and press SOURCE.
4. Press EXIT.
Some RDS stations broadcast information,
such as about programme content and artists.
Hold the FM button depressed a few seconds
to access any transmitted radio text, which then
appears on the display.
After the text is shown twice, the radio once
again displays the station/frequency.
A brief press on EXIT ends the radio text
display.
ASC (Active Sound Control)
The ASC function automatically adapts the
volume of the radio to vehicle speed.
Activating ASC:
1. Select radio mode using the FM button and
press SOURCE.
2. Turn SOURCE, select ADVANCED
MENU and press SOURCE.
3. Turn SOURCE, select AUDIO SETTINGS
MENU and press SOURCE.
4. Turn SOURCE, select ASC LEVEL and
press SOURCE.
5. Turn SOURCE select LOW, MEDIUM,
HIGH or Off and press SOURCE.
179
Cassette player HU-450/650
DOLBYBNR
3905010m
3901857d
3901876d
3901873d
Cassette opening
Cassette eject
Fast forward/rewind
Slide cassette into the cassette opening with the
tape to the right. TAPE Side A is shown in the
display. When one side has finished playing the
system will automatically begin playing the
other side (auto reverse). To play a cassette that
is already in the player, turn the SOURCE knob
or press the TAPE shortcut key (HU-450).
If you press the button, the tape stops and the
cassette is ejected. Turn the SOURCE knob to
select a new programme source. The cassette
can be inserted or ejected even if the system is
switched off.
The tape is fast forwarded by pressing and
holding the button and is rewound with the
button . ”FF” (fast forward) or ”REW”
(rewind) is shown in the display during this
time. Fast forward/rewind is interrupted if you
press the button again.
Changing tape direction
This function is preset. Do as follows to switch
it off: hold the REV button depressed until the
Dolby symbol
in the display goes out. Press
the same button again to reactivate the Dolby
function.
Press the REV button to if you wish to play
the other side of the tape. The display shows
which side is being played.
Dolby B Noise Reduction
Scanning
Scan plays the first ten seconds of each track.
Press the SCAN or EXIT button when you
find a song or track you wish to listen to.
180
Next track, Previous track
If you press the button, the cassette will
automatically fast forward to the next song.
If you press the button, the cassette will
automatically rewind to the previous
song.There must be a five second break
between each track for this function to work. If
you have a keypad in the steering wheel, you
can use the arrows.
CD player HU- 650
3901862d
3905010m
CD player
Insert a CD. If there is already a CD in the
player, activate it by turning the SOURCE knob
or pressing the CD shortcut key.
CD eject
If you press this button the CD stops playing
and the disc is ejected. (See illustration above)
NOTE! For reasons of traffic safety, you have
twelve seconds to handle the ejected disc.
Otherwise, the CD is drawn back into the player
and resumes with the most recently played
track.
Fast forward/reverse and
change track
Press and hold down the right or left-hand
arrow key to fast forward/reverse a track or the
whole disc. Fast forward/reversing cannot be
done using the steering wheel keypad.
Briefly press the left or right-hand arrow key to
go to the previous or next track. The steering
wheel keypad can also be used for this. Track
numbers are shown in the display.
Random
Press RND to connect the random function.
The unit plays tracks from the disc in random
order. “RND” (random) is displayed as long as
the function is activated.
NOTE! If the quality of the CD does not comply
with the standard EN60908, or if it has been
recorded using poor equipment, sound quality
may be poor or playback interrupted.
Scanning
Scan plays the first ten seconds of each track.
Press the SCAN or EXIT button when you
find a song or track you wish to listen to.
IMPORTANT!
Use only standard 12 cm CDs - no smaller.
Do not use CDs with a sticker label.
Heat from the CD player could cause the
label to let loose from the disc, possibly
damaging the CD player.
181
External CD changer
3905010m
3903125m
CD changer
The external CD changer (option) is mounted
behind the panel on the rear left side of the
cargo compartment.
Turn the SOURCE knob to activate CD
changer mode. The CD changer resumes
playing the disc and track that was playing last.
If the CD changer magazine is empty
“LOAD CARTRIDGE” is displayed.
Loading discs in the CD changer:
1. Slide open the CD changer cover.
2. Press the cartridge eject button on the
changer.
3. Pull out the CD cartridge and insert the
discs.
4. Reinsert the cartridge in the CD changer.
Selecting disc number
Turn the PRESET/CD knob. The numbers of
the disc and the track are shown in the display.
182
Fast forward/reverse and
change track
Press and hold down the right or left-hand
arrow key to fast forward/reverse a track or the
whole disc. Fast forward/reversing cannot be
done using the steering wheel keypad.
Briefly press the left or right-hand arrow key to
go to the previous or next track. The steering
wheel keypad can also be used for this. Track
numbers are shown in the display.
Scanning
Scan plays the first ten seconds of each track.
Press the SCAN or EXIT button when you find
a song or track you wish to listen to.
Random
Press RND (for HU-650 and 850) to activate
the Random function. If you have audio system
HU-450, use the REV button. A randomly
selected track is chosen from a randomly
selected disc. Then a new track is selected in the
same way. “RND” (random) is displayed as
long as the function is activated.
NOTE! If the quality of the CD does not comply
with the standard EN60908, or if it has been
recorded using poor equipment, sound quality
may be poor or playback interrupted.
IMPORTANT!
Use only standard 12 cm CDs - no smaller.
Do not use CDs with a sticker label.
Heat from the CD player could cause the
label to let loose from the disc,
possibly damaging the CD player.
Internal CD changer HU-850
3901862d
3905010m
Internal CD changer
Selecting disc number
Random
HU-850 contains an internal 6-disc CD
changer.
Press the CD shortcut key or turn the SOURCE knob to activate the CD player. The CD
player resumes with the most recently played
track of the most recently played CD. Up to 6
discs can be inserted in the CD player. An
empty slot in the player must be selected when
inserting a disc.This is done by turning the
PRESET/CD knob. Make sure ”LOAD DISC”
is displayed before inserting a new disc.
Turn the PRESET/CD knob. The disc and track
numbers are shown on the display.
Press RND to connect the random function.
A randomly selected track is chosen from a
randomly selected disc. Then a new track is
selected in the same way. “RND” (random) is
displayed as long as the function is activated.
CD eject
If you press this button the CD stops and the
disc that was playing is ejected.
NOTE! For traffic safety reasons you have
twelve seconds to handle the ejected CD.
Otherwise, the CD is drawn back into the
player and resumes with the most recently
played track.
Fast forward/reverse and
change track
Press and hold down the right or left-hand
arrow key to fast forward/reverse a track or
the whole disc. Fast forward/reversing cannot
be done using the steering wheel keypad.
Briefly press the left or right-hand arrow key
to go to the previous or next track. The
steering wheel keypad can also be used for
this. Track numbers are shown in the display.
Scanning
Scan plays the first ten seconds of each track.
Press the SCAN or EXIT button when you
find a song or track you wish to listen to.
NOTE! If the quality of the CD does not comply
with the standard EN60908, or if it has been
recorded using poor equipment, sound quality
may be poor or playback interrupted.
IMPORTANT!
Use only standard 12 cm CDs - no smaller.
Do not use CDs with a sticker label.
Heat from the CD player could cause the
label to let loose from the disc,
possibly damaging the CD player.
183
Dolby Surround Pro Logic II HU-850
Dolby Surround Pro Logic II
Dolby Surround Pro Logic II is a further refinement of the previous system and provides a
significantly improved sound experience. This
improvement is especially noticeable to rear
seat passengers.
Dolby Surround Pro Logic II together with a
centre speaker in the dashboard offers a sound
experience very close to being there.
The normal left-right stereo channels are
divided into left-centre-right. In addition,
surround sound is produced by the rear
speakers. Dolby Surround Pro Logic II works
in CD mode. 3-channel stereo (3-CH) is
recommended for AM and FM radio transmissions.
184
3901877d
3905088d
Dolby Surround Pro Logic II
Mode
To select Dolby Surround Pro Logic II Mode,
press “ PL II”. “PL II” is shown on the
display. “Dolby Pro Logic” is displayed. Press
OFF to return to 2-channel stereo.
3-channel stereo
To select 3-channel stereo press “3-CH”.
“3-CH” is displayed. Press OFF to return
to 2-channel stereo.
Dolby Surround Pro Logic II HU-850
3902419d
Centre loudspeaker volume
Set the centre loudspeaker volume by pressing
out the button and turning it left or right. In
the centre position the volume is “normalised”
Press the button back after setting.
3902419d
Rear loudspeaker output
level (surround sound)
Set the power output of the rear channels by
pressing out the button, pulling it further out
and turning it left or right. In the centre position
the power output is “normalised”. Press the
button back after setting. The control regulates
the surround sound level when listening in
Dolby Surround Pro Logic II mode.
185
Technical data - Audio
HU-450
Output:
Impedance:
Voltage required:
Alarm
4 x 25 W
4 Ohm
12 V, negative ground
“Alarm!” is shown in the radio display when an alarm message is
transmitted. The function is used to warn the driver of serious
accidents or catastrophes, such as collapsed bridges, earthquakes or
nuclear accidents.
Radio
Frequency:
U (FM)
M (AM)
L (AM)
87.5 - 108 MHz
522 - 1611 kHz
153 - 279 kHz
Dolby Noise Reduction is manufactured under license of Dolby
Laboratories Licensing Corporation. Dolby and the double D
symbol
are trademarks of Dolby Laboratories Licensing
Corporation.
HU-650
Output:
Impedance:
Voltage required:
External amplifier:
4 x 25 W
4 Ohm
12 V, negative ground
4 x 50 W or 4 x 75 W (option)
Radio
Frequency:
U (FM)
M (AM)
L (AM)
87.5 - 108 MHz
522 - 1611 kHz
153 - 279 kHz
Bass speaker
Built-in amplifier:
150 W
Low battery voltage
If battery voltage is low, a text appears in the combined instrument
panel display. The energy economy function of the car may switch off
the radio.Charge the battery by starting the engine.
186
Dolby Surround Pro Logic II is a registered trademark of Dolby
Laboratories Licensing Corporation. Manufacturing rights for Dolby
Pro Logic Surround System are licensed from Dolby Laboratories
Licensing Corporation.
HU-850
Output:
Impedance:
Voltage required:
External amplifier:
1 x 25 W (Centre speaker)
4 Ohm
12 V, negative ground
4 x 50 W or 4 x 75 W (option)
HU-850 must be connected to an external amplifier.
Radio
Frequency:
U (FM)
M (AM)
L (AM)
87.5 - 108 MHz
522 - 1611 kHz
153 - 279 kHz
Telephone (option)
Telephone system
188
Operating
190
Call options
191
Memory functions
194
Menu functions
195
Miscellaneous information
199
187
Telephone
Telephone system
General rules
1. Keypad in centre console
5. SIM card
· Put traffic safety first! If you as the
driver must use the privacy handset
in the armrest, park the car in a safe
place.
· Switch off the telephone when
refuelling.
· Switch off the telephone in areas
where blasting work is being carried
out.
· Only allow authorised personnel
service your telephone.
All telephones system functions can be
controlled from the keypad in the centre
console.
All telephone functions can be controlled via
the keypad in the centre console. The majority
of telephone functions can be controlled via the
steering wheel keypad. The SIM card is
inserted below the keypad in the centre console.
Emergency calls
Emergency calls to emergency services
can be made without the ignition key or
the SIM card.
· Press the ON/OFF button.
· Ring the emergency number that
applies to your region
(within EU: 112).
.
· Press the green button
188
2. Steering wheel keypad
The keypad in the steering wheel can be used
for most telephones system functions.
When the telephone is activated, the keypad in
the steering wheel can only be used for telephone
functions. When in active mode, telephone
information is always shown in the display.
To use the buttons for radio settings, the
telephone has to be deactivated, see page 190.
Switch off the telephone whenever a SIM card
is not in use. Otherwise, messages from other
functions cannot be shown on the display.
6. Microphone
The microphone is built into the rearview
mirror.
3. Display
7. Speaker
The display shows menu functions, messages,
telephone numbers, etc.
The speaker is integrated in the driver’s seat
head restraint.
4. Privacy handset
The privacy handset can be used for private
conversations when you do not wish to be
disturbed.
8. Antenna
The antenna is mounted against the windscreen
in front of the rearview mirror.
Telephone
2
8
3
1
6
5
7
4
3903012m
189
Telephone
Operating
3903022m
3902219d
3903019m
SIM card
Switching the telephone on and off
Active mode
The telephone can only be used in conjunction
with a valid SIM card (Suscriber Identity
Module). Obtain the card from your service
provider.
To switch the telephone on: turn the ignition key
to position I. Press the button marked in the
illustration
The telephone must be in active mode to use its
functions (does not apply to receiving calls).
To switch the telephone off: press the same
button for approx. 3 seconds. If you switch off
the car while the telephone is on, it will be on
the next time you switch on the ignition.
on the
Activate the telephone by pressing
centre console keypad or the keypad in the
steering wheel.
When in active mode, telephone information is
always shown in the display.
to deactivate the telephone.
Press
Always insert the SIM card to use the
telephone. The name of your service provider
will then be displayed.
Switch off the telephone whenever a SIM card
is not in use. Otherwise, message from other
functions cannot be shown on the display and
the keypad cannot be used to control the radio.
190
Telephone calls cannot be received if the
telephone is switched off.
Telephone
Call options
3800670d
3902219d
3902220d
Display
Making and receiving calls
Ending a call
The display shows the current function, such as
menu alternative, message, telephone number,
or setting.
To place a call: enter the number and press
on the steering wheel or centre console keypad
(or lift up the handset).
To conclude a call, press
on the steering
wheel or centre console keypad or put the
handset back in place. The audio system will
resume its previous activity.
To receive an incoming call: Press the button
(or lift the privacy handset). You can also use
Automatic answer, see menu function 4.3.
The audio system is automatically muted during
conversation. See menu alternative 5.6.5
regarding audio system volume.
191
Telephone
Call options (cont.)
Speed dial
Storing speed dial numbers
A number stored in the telephone book can be
linked to a speed dial button (0-9) as follows:
1. Go into active mode. Scroll with
memory (Menu 3) and press
.
to Edit
2. Scroll to Speed dial (Menu 3.4) and
.
press
3. Choose the digit that is to be the speed dial
to confirm.
number. Press
3902219d
3902215d
Last number called
Privacy handset
The telephone automatically stores the last
telephone numbers/names called.
If you wish to talk undisturbed, use the privacy
handset.
on the steering wheel or centre
1. Press
console keypad.
1. Pick up the handset. Enter the chosen
number on the centre console keypad.
Press
to place a call. Adjust the
volume by using the knob on the side of
the handset.
or
2. Use the arrows to scroll forward
backward
through the last numbers
called.
3. Press
(or lift the privacy handset) to
make the call.
192
2. The call is terminated when you replace
the handset in its holder. If you wish to
change to handsfree without ending the call:
and select Handsfree. Press
press
and put down the handset, see the following
page.
4. Find the desired name or telephone number
to select it.
in the memory and press
Using speed dial
Press the desired speed dial button for about
2 seconds to make a call.
NOTE! When you turn on the telephone, wait
a moment before using the speed dial function.
To enter a speed dial number, Menu 4.5 must
be activated, see page 196.
Telephone
Functions during a call
The following functions are available during
a call (scroll with arrows):
The following functions are available during
three-way calling (scroll with arrows):
Secret mode/
Secret mode off
Secret mode/
Secret mode off
Secret mode
Hold/No hold
Choose if the present
call is to be parked, i.e.
put on hold
Handset/
Handsfree
Memory
Handset/
Handsfree
Use the handset or
handsfree
Show stored numbers
The following functions are available when you
have a current call and a parked call (scroll
with arrows):
Secret mode/
Secret mode off
Handset/
Handsfree
Memory
Secret mode
Use the handset or
handsfree
Show stored numbers
Three-way calling Speak with both parties
simultaneously
(conference call)
Switch
Switch between the two
calls
Memory
Secret mode
Use the handset or
handsfree
Show stored numbers
Call waiting
If you hear a beep in your receiver followed
immediately by two beeps (double beep) during
a phone call, someone else is calling.
The double beep is then repeated until you
either answer or the caller hangs up.
In this mode, you can choose to either take the
call or ignore it.
If you do not wish to take the call, press
or do nothing.
If you do wish to take the call, press
.
Your current call will be put in “park mode”.
If you press , both calls will be terminated.
3902223d
Volume
Increase volume by pressing on the (+) button
on the steering wheel keypad. Reduce volume
by pressing on the (-) button.
When the telephone has been activated, the
steering wheel keypad can only be used for
telephone functions.
To use this keypad for radio settings the
telephone has to be deactivated, see page 190.
SMS
A double beep informs you that a SMSmessage has been received.
193
Telephone
Memory functions
Enter a name (or message)
Telephone numbers and names can be stored
in either the telephone memory or the SIM card
memory.
Press the button with the desired character:
once for the first character, twice for the
second, etc. Press 1 to enter a space.
If the number of the person calling is in the
memory, their name is shown in the display.
Up to 255 names can be stored in the telephone
memory.
Storing telephone
numbers with names
1. Press
and scroll to Edit memory
(Menu 3) and press
.
2. Scroll to Enter item in memory (Menu 3.1)
and press
.
3. Enter a number and press .
4. Enter a name and press .
5. Choose in which memory to save with
and press
.
194
space 1- ? ! , . : ’ ( )
abc2äå àáâ æç
def 3èéëê
gh i 4 ì í î ï
jkl5
mno6ñöòóØ
pqrs7ß
tuv8üùúû
wxyz9
if you enter two letters in a row from
the same button, press * between them
or wait a few seconds
+0@* #& $ £ / %
change between capital and lower case
letters
delete the last letter or number entered.
If you press the button for a long time,
the entered number or text is deleted.
3902221d
Calling from the memory
1. Press
.
2. Choose from the following alternatives:
· Press and scroll with the arrows
until you find the desired name.
· Press the key of the first letter in the
name (or enter the name) and press .
3. Press
to call the selected number.
Telephone
Menu functions
Traffic safety
The menu function is used to check and alter
settings and programme new functions in your
system. The different menus are shown in the
display.
For reasons of safety, the menu system cannot
be accessed at speeds in excess of 8 km/h
(5 mph). You may only complete activities in
the menu system that have already been started.
The speed limiter can be disconnected using
menu function 5.7.
Menu function
Go into active mode. Press
menu function.
to come to the
The following applies in the menu function:
·
·
·
·
3902222d
A long press on
means you exit the
menu function.
A short press on
means that you retract,
cancel or reject an alternative.
A press on
means that you confirm or
select, or that you scroll from a submenu
to the next submenu.
The right arrow
leads to the next side
menu. The left arrow
leads to the
previous side menu.
Shortcuts
When you use the right arrow
to enter the
menu system, you can use numbers instead of
the arrows and the green button
to select the
right menu on the main menu level (1, 2, 3,
etc.), first submenu level (1.1, 2.1, 3.1, etc.)
and the second submenu level (1.1.1, 2.1.1,
etc.). The numbers are shown in the display
together with the menu alternative.
195
Telephone
Main menus/submenus
1. Call register
1.1
1.2
1.3
1.4
1.5
Missed calls
Received calls
Dialled calls
Erase list
1.4.1 All
1.4.2 Missed
1.4.3 Received
1.4.4 Dialled
Call duration
1.5.1 Last call
1.5.2 Number of calls
1.5.3 Total time
1.5.4 Clear
3. Edit memory
3.1
3.2
3.3
Enter item
Search
3.2.1 Edit
3.2.2 Erase
3.2.3 Copy
3.2.4 Move
Copy all
3.4
3.5
3.6
3.7
3.3.1 SIM to phone
3.3.2 Phone to SIM
Speed dial
Empty SIM
Empty memory
Status
5. Settings
5.1
5.2
5.3
2. Messages
2.1
2.2
2.3
2.4
196
Read
Write
Voice message
Settings
2.4.1 SMSC number
2.4.2 Validity
2.4.3 Type
4. Call options
4.1
4.2
4.3
4.4
4.5
4.6
Transmit numbers
Call waiting
Automatic answer
Automatic dial
Speed dial
Call divert service
4.6.1 All calls
4.6.2 When busy
4.6.3 When not answered
4.6.4 If unreachable
4.6.5 Fax calls
4.6.6 Computer calls
4.6.7 Cancel all diverts
5.4
5.5
5.6
5.7
Factory settings
Network selection
Language
5.3.1 English UK
5.3.2 English US
5.3.3 Svenska
5.3.4 Dansk
5.3.5 Suomi
5.3.6 Deutsch
5.3.7 Nederlands
5.3.8 Français FR
5.3.9 Français CAN
5.3.10 Italiano
5.3.11 Español
5.3.12 Português P
5.3.13 Português BR
SIM security
5.4.1 On
5.4.2 Off
5.4.3 AUTO
Change codes
5.5.1 PIN code
5.5.2 Telephone code
Volume
5.6.1 Ringer volume
5.6.2 Ringer tone
5.6.3 Button click
5.6.4 Speed volume
5.6.5 Radio Auto Suppression
Traffic safety
Telephone
Menu 1. Call register
Menu 2. Messages
Menu 3. Edit memory
1.1 Missed calls: A list of missed calls is
shown here. You can choose to call, erase or
store the number in the telephone or SIM card
memory for later use.
2.1 Read: Here you can read received text
messages. You can then choose to erase the
last message, forward it, change or save the
entire message or parts of it.
3.1 Enter item: You can store names and
telephone numbers in the telephone or SIM
card memory. See the section on memory
functions for more information.
1.2 Received calls: A list of received calls is
shown here. You can choose to call, erase, or
store the number in the telephone or SIM card
memory for later use.
2.2 Write: Using the keypad, you can write a
text message. Then choose to save or send it.
3.2 Search: Changes in the memory can be
made here.
3.2.1 Edit: Change data in the different
memories.
3.2.2 Erase: Remove a saved name.
3.2.3 Copy: Copy a saved name.
3.2.4 Move: Transfer information between
the memory of the telephone and the SIM
card.
1.3 Dialled calls: A list of dialled numbers is
shown here. You can choose to call, erase, or
store the number in the telephone or SIM card
memory for later use.
1.4 Erase list: This option can be used to
erase the list of menus 1.1, 1.2 and 1.3 as
follows.
1.4.1 All
1.4.2 Missed
1.4.3 Received
1.4.4 Dialled
1.5 Call duration: Here you can see the
duration of all your calls or the most recent.
You can also choose to see the number of calls
and clear the call timer.
1.5.1 Last call
1.5.2 Number
1.5.3 Total time
1.5.4 Clear timer
The telephone code is needed to clear the call
timer (see Menu 5.5).
2.3 Voice massage: Listen to received
messages.
2.4 Settings: Enter the number (SMSC
number) of the message centre you wish to
have transfer your messages. Specify also how
the message is to reach the addressee and how
long it is to be stored in the message centre.
2.4.1 SMSC number
2.4.2 Validity
2.4.3 Type
Contact your service provider for information
about these settings and the SMSC number.
3.3 Copy all: Copy the telephone numbers and
names on the SIM card to the telephone's
memory.
3.3.1 From SIM to telephone memory
3.3.2 From Telephone to SIM memory
3.4 Speed dial: A number stored in the
telephone book can be stored as a speed dial
number.
3.5 Empty SIM: The entire memory of the
SIM card can be erased.
3.6 Empty memory: The entire memory of the
phone can be erased.
3.7 Status: See how many places in the SIM
card or telephone memory are occupied by
names and numbers.
197
Telephone
Menu 4. Call options
Menu 5. Settings
4.1 Transmit number: Choose whether or not
to display your number to the person you call.
Contact your service provider for a permanently
concealed number.
5.1 Factory settings: Function to return to
the system’s factory settings.
4.2 Call waiting: Choose whether or not you
want to be alerted during a phone call that there
is another call coming in.
4.3 Automatic answer: Chose to answer
without using the keypad.
4.4 Automatic redial: Choose to call a
previously dialled number that was busy.
4.5 Speed dial: Here you set whether or not
speed dial is to be activated. In order to use
speed dial, the function must be activated
4.6 Call divert service: Here you can choose
when and what type of calls are to be diverted
to a specified telephone number.
4.6.1 All calls (this setting only applies
during the current call).
4.6.2 When busy
4.6.3 When not answered
4.6.4 If unreachable
4.6.5 Fax calls
4.6.6 Computer calls
4.6.7 Cancel all diverts
198
5.2 Network selection: Choose a network
automatically or manually.
5.2.1 Auto
5.2.2 Manual
5.3 Language: Here you can choose which
language the telephone is to display.
5.3.1 English UK
5.3.2 English US
5.3.3 Svenska
5.3.4 Dansk
5.3.5 Suomi
5.3.6 Deutsch
5.3.7 Nederlands
5.3.8 Français FR
5.3.9 Français CAN
5.3.10 Italiano
5.3.11 Español
5.3.12 Português P
5.3.13 Português BR
5.4 SIM security: Choose if the PIN code is to
be on, off, or automatic.
5.4.1 On
5.4.2 Off
5.4.3 Auto
5.5 Change codes: Change the PIN code or
telephone code.
5.5.1 PIN code
5.5.2 Telephone code (use 1234 before
you change to a personal code).
The telephone code is used to clear
the call timer.
NOTE! Make a note of the code and store it in
a safe place.
5.6 Volume
5.6.1 Ringer volume: Here you can
choose the volume of the ringer for
incoming calls.
5.6.2 Ringer tone: There are eight
different ringer tones to choose
from.
5.6.3 Button click: On or off
5.6.4 Speed volume: Choose whether the
volume should be adjusted
according to speed.
5.6.5 Radio Auto Suppression: Here you
choose whether the volume of the
radio should remain the same during
telephone calls.
5.6.6 New SMS: Choose whether you
want the telephone to signal an
incoming SMS or not.
5.7 Traffic safety: Here you can choose to
disengage the speed limiter for the menu
system, i.e. choose to use the menu system
even while driving.
Telephone
Miscellaneous information
Specifications
Output
SIM card
Memory positions
SMS (Short Message Service)
Computer/Fax
Dual band
3902239d
3903022m
2W
small
255*
Yes
No
Yes
(900/1800)
* 255 memory positions in the telephone
memory. The number of memory positions on
the SIM card varies depending on your
subscription.
IMEI number
Radio - Telephone
Double SIM card
The four lowest buttons in the steering wheel
keypad are for both radio and telephone.
Many service providers offer double SIM cards,
one for the car and a second one for another
telephone. Double SIM cards give you the
same number for two separate telephones. Ask
your service provider about the possibilities and
offers available regarding double SIM cards.
If you wish to control telephone functions with
these buttons, you must first activate the
telephone; see page 188. If you wish to adjust
the radio settings with these buttons, exit the
telephone active mode. Press .
To block the telephone, inform the service
provider of the telephone IMEI number. This is
a 15 digit serial number programmed in the
telephone. Dial *#06# to display this number.
Write down the number and store it in a safe
place.
199
200
Index
A
ABS .....................................................110
AC .......................................................... 60
Activating the alarm .............................. 83
Active mode ........................................ 190
Actual temperature - ECC ...................... 55
Air distribution ................................. 54, 61
Air quality sensor .................................. 57
Air vents ................................................ 54
Alarm .............................................. 83, 186
Anti-lock brakes (ABS) ....................... 111
Audio system ...................................... 167
AUTO DOWN ....................................... 48
AUTO UP .............................................. 48
AUTO ..................................................... 57
AUTO (climate control ECC) ............... 58
AUTOUP/DOWN (power windows) ...... 48
Autodim ................................................ 49
Automatic gearbox ......................... 92, 93
Automatic gearbox with manual
positions (Geartronic) ..................... 94, 95
Automatic relocking ............................. 80
Average fuel consumption .................... 40
Axle load ............................................. 157
B
Battery (jump start) ............................... 99
Battery care ................................ 152, 153
Battery ................................................. 144
Bird droppings .................................... 140
BLIS (Blind Spot Information
System) ................................................113
Bonnet .................................................145
Booster battery ...................................... 99
Booster cushion .................................... 28
Brake fluid ..........................................151
Brake system .............................. 110, 111
Bulbs ...................................................166
C
Call options .........................................191
Car washes ........................................... 141
Cargo compartment .............................. 71
Cassette player .................................... 180
CD changer .........................................182
CD player ................................... 181, 183
Changing bulbs ..................................131
Changing wheels ................................122
Children in the car seating locations ................................... 27
Cigarette lighter socket ........................ 47
Cleaning the seat belts .......................141
Cleaning the upholstery .....................141
Climate control with
air conditioning (AC) ............................ 60
Coat hanger ........................................... 73
Colour code ......................................... 139
Combined instrument panel .................. 32
Cruise control ........................................ 41
Current fuel consumption ..................... 40
D
D Drive .................................................. 92
Dashboard - LHD .................................... 2
Dashboard - RHD .................................... 3
Deactivating deadlocks ........................ 81
Deactivating the alarm ......................... 83
Deadlocks .............................................. 81
Defroster .......................................... 58, 61
Diesel fuel filter ..................................147
Diesel ...................................... 45, 88, 147
Dimensions and weights .....................157
Direct start of heater .............................. 63
Direction indicators .............................. 43
Dolby Pro Logic Surround Sound ......184
Door mirror defroster ............................ 46
Double SIM card .................................199
Drive position ....................................... 45
Driving with trailer ..................... 100-103
DSTC ..................................................... 35
E
ECC ....................................................... 58
Electric cooling fan ................... 145, 146
Electric socket ....................................... 47
Electronic Climate Control (ECC) ....... 56
Emergency calls ..................................188
Emergency stop (power seat) ................ 68
Engine - Specifications .............. 158, 159
Engine compartment ................. 145, 146
201
Index
Engine oil ................................... 148, 149
Engine type designation ....................156
Environmental care ...................... 55, 144
Exterior .................................................... 6
F
Fan ......................................................... 60
Fault in emission control system .......... 36
Fault in SRS .......................................... 36
FIX NEXT SERVICE ............................ 37
Floor support ......................................... 72
Follow-me-home lighting ..................... 81
Frequency update ............................... 178
Front seats ............................................. 66
Fuel filler flap ........................................ 88
Fuel gauge ............................................. 32
Function selector .................................. 61
G
Gearbox type designation ..................156
Geartronic .............................................. 93
General lighting .................................... 69
Generator not charging ......................... 36
H
Handbrake ............................................. 47
Hazard warning flashers ........................ 46
Headlamp washer .................................. 44
Head restraints, rear ............................... 67
202
Heated front seats .................................. 46
Heating/Cooling ................................... 60
HU-403 ................................................167
HU-603 ................................................169
HU-803 ................................................170
I
Ignition switch and steering
wheel lock ............................................. 45
Immobilizer ..................................... 78, 90
Indicator and warning lamps .......... 33-36
Interior - LHD .......................................... 4
Interior - RHD .......................................... 5
Interior lighting .................................... 69
J
Jack ............................................... 72, 123
Jumpstarting .......................................... 99
Keys ....................................................... 78
Kick-down ............................................. 90
L Low gear ............................................ 92
Lifting the car ...................................... 144
Load carrier .........................................106
Load curtain in cargo compartment ..... 71
Location of children in the car ............. 27
Locking and unlocking ........................ 79
Long load .............................................. 74
Lowering the backrest, rear .................. 74
Lowering the front passenger seat ........ 67
M
Manual child safety locks .................... 82
Manual climate control with
air conditioning (AC) ..................... 53, 60
Manual gearbox .................................... 91
Master key ............................................. 78
Mechanical child safety locks ............. 82
Minor stone chips and scratches ........ 139
Mirrors ................................................... 49
Misting on window interiors ................ 55
Mounting .............................................. 72
Multifilter .............................................. 57
N
N Neutral ............................................... 92
O
Oil pressure ........................................... 36
Open boot lid ........................................ 94
Opening the fuel filler flap ................... 88
P
P Parking ............................................... 92
Paintwork damage ..............................139
Paintwork ............................................139
Parking brake engaged ......................... 36
Parking brake ........................................ 47
Petrol ...................................................164
Polishing and waxing .........................141
Index
Pollen filter ........................................... 55
Power seat .............................................. 68
Power steering .....................................151
Power sunroof ........................................ 50
Power windows ..................................... 48
R
R Reverse .............................................. 92
Radio ...................................................167
Range to empty fuel tank ..................... 40
Reading lamps, front and rear .............. 69
Rear fog lamp ........................................ 36
Rear seat head restraints ....................... 67
Rear window defroster .......................... 46
Rearview and door mirrors ................... 49
Rearview mirror .................................... 49
Recirculation ........................................ 59
Recovery ............................................... 98
Refuelling ............................................. 88
Remote control ..................................... 68
Replacing remote control batteries ...... 80
Roof load ............................................. 157
Rustproofing .......................................138
S
Seat belts ......................................... 10, 11
Seat setting ............................................ 66
SEE MANUAL ...................................... 37
Service key ............................................ 78
SERVICE REQUIRED .......................... 37
SERVICE URGENT .............................. 37
SIM card ..............................................190
Ski hatch ............................................... 74
Slippery road surfaces ........................... 89
Spare wheel .................................. 72, 121
Spare wheel ”Temporary Spare” ......... 121
SRS (airbags) ................................... 12-17
Start position ......................................... 45
Starting the engine ................................ 88
Steering wheel adjustment ................... 43
Stone chips .......................................... 139
STOP SAFELY ASAP ............................ 37
Storage compartments in the
centre console ....................................... 71
Storage ................................................... 70
Suitable detergent ............................... 140
Sun blind ............................................... 51
Sunroof .................................................. 50
Switches in the centre console ............. 38
Symbols ............................................... 152
T
Telephone system ............................... 188
Temperature selector ....................... 58, 70
Temperature ........................................... 58
Temporary puncture repair ................. 121
”Temporary Spare” .............................. 121
Tool kit with towing eye ...................... 72
Tools ...................................................... 72
Total weight ........................................157
Towbar .................................................102
Towbar - detachable (mounting) ........ 104
Towbar - detachable (removal) ...........105
Towing equipment ..................... 102, 103
Towing ................................................... 98
Traffic safety .......................................195
Trailer indicator lamp ........................... 36
Trailer weight ...................................... 157
Trailer .................................................. 101
Train weight ........................................157
Trip computer ........................................ 40
Type designations ............................... 156
Tyres .................................................... 118
Tyre dimensions ..................................118
Tyre, direction of rotation ...................121
Tyre, driving characteristics ............... 120
Tyre, fitting .........................................123
Tyre, air pressure .................................120
Tyre, removing .................................... 122
Tyre, tread wear indicators ..................121
U
Unlocking boot lid with master key .... 80
V
Vanity mirror ......................................... 69
Ventilation ............................................ 53
203
Index
VIN ...................................................... 156
Volvo integrated booster cushion ......... 28
Volvo Service Programme .................... 143
W
Warning - fault in ABS system ............. 34
Warning - fault in brake system ............ 34
Warning symbol in centre of
dashboard .............................................. 33
Warning triangle .......................... 72, 122
Washer fluid ........................................ 151
Washing ............................................... 140
Wheels and tyres ................................. 118
WHIPS ............................................. 21, 22
Windscreen washer ................................ 44
Windscreen wipers ................................ 44
Winter tyres .........................................119
Wiper blades, replacement ..................154
204
205
206
207
208
209
210
VOLVO
TP 7809 (English). AT 0520. Printed in Sweden, Elanders Infologistics Väst AB, Mölnlycke 2005
OWNERS MANUAL S80
2006