Samsung UD55A User manual

SyncMaster UD55A
LCD Display
User Manual
The color and the appearance may differ depending on the
product, and the specifications are subject to change
without prior notice to improve the performance.
Safety Instructions
Notational
Note
These safety instructions must be followed to ensure your safety and prevent property damage.
Make sure to read the instructions carefully and use the product in the correct manner.
Warning / Caution
Failure to follow directions noted by this symbol could result in bodily harm
or damage to the equipment.
Note
•
•
Prohibited
Important to read and understand at all times
Do not disassemble
Disconnect the plug from the
outlet
Do not touch
Ground to prevent an electric
shock
An administration fee may be charged if either
•
(a) an engineer is called out at your request and there is no defect in the product(i.e.
where you have failed to read this user manual)
•
(b) you bring the unit to a repair centre and there is no defect in the product(i.e.
where you have failed to read this user manual).
The amount of such administration charge will be advised to you before any work or
home visit is carried out.
Power
When not used for extended period of time, set your computer to DPM.
If using a screen saver, set it to active screen mode.
The images here are for reference only, and are not applicable in all cases (or
countries).
Shortcut to Anti-Afterimage Instructions
Do not use a damaged power cord or plug or a damaged or loose power
outlet.
•
Otherwise, this may result in electric shock or fire.
Safety Instructions
Do not touch the power plug with wet hands when removing or plugging the plug into the outlet.
•
Otherwise, this may result in electric shock.
Make sure to connect the power cord to a grounded power outlet.
•
Otherwise, it may result in electric shock or personal injury.
Ensure that the power plug is plugged into the power outlet firmly and
correctly.
•
Otherwise, this may result in fire.
Do not forcefully bend or pull the power plug and do not place any
heavy material on it.
•
Otherwise, this may result in fire.
Do not connect multiple appliances to the same power outlet.
•
Otherwise, this may cause fire due to overheating.
Do not disconnect the power cord while using the product.
•
Otherwise, this may result in damage to the product due to electric
shock.
To disconnect the apparatus from the mains, the plug must be pulled
out from the mains socket, therefore the mains plug shall be readily operable.
•
Otherwise, this may cause electric shock or fire.
Use only the power cord provided by our company. Do not use the
provided power cord of another product.
•
Otherwise, this may result in fire or electric shock.
Connect the power plug to a wall outlet that can be easily reached.
•
When a problem occurs with the product, you must unplug the power
plug to cut the power off completely. You cannot cut the power off
completely using only the power button on the product.
Installation
Be sure to contact an authorized Service Center when installing your monitor in
a location with heavy dust, high or low temperatures, high humidity, and exposed
to chemical substances and where it operates for 24 hours such as at airports,
train stations etc.
Failure to do so may cause serious damage to your monitor.
Safety Instructions
Ensure that at least two persons lift and move the product.
•
Otherwise, it may be dropped and cause personal injury, and/or damage the product.
When installing the product in a cabinet or rack, make sure that the
front end of the bottom of the product does not project out.
•
Otherwise, it may fall or cause personal injury.
•
Use a cabinet or rack of a size appropriate to the product.
DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGARETTES AND ANY HEATING APPLIANCES NEAR THE PRODUCT.
•
Otherwise, this may result in fire.
Keep heating appliances as far away from the power cord or the product as possible.
•
Otherwise, this may result in electric shock or fire.
Do not install it in a badly ventilated location such as a bookcase or
closet.
•
Otherwise, this may result in fire due to an increase in the internal
temperature.
When putting the product down, make sure to put it down softly.
•
Otherwise, this may result in damage to the screen display.
Do not place the front of the product on the floor.
•
Otherwise, this may result in damage to the screen display.
Ensure that an authorized installation company installs the wall mount.
•
Otherwise, it may fall and cause personal injury.
•
Make sure to install the specified wall mount.
Install your product in a well ventilated location. Ensure that there is
a clearance of more than 4 inches (10 cm) from the wall.
•
Otherwise, it may result in fire due to an increase in the internal temperature.
Ensure that the packaging vinyl is kept away from children.
•
Otherwise, it may result in serious harm (suffocation) if children play
with it.
If the height of your monitor is adjustable, do not place any object or
part of your body on the stand when lowering it.
•
This may cause damage to the product or the person carrying it.
Safety Instructions
Clean
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe
with a slightly moistened, soft cloth.
Do not spray cleaner directly onto the surface of the product.
•
Otherwise, this may result in the discoloration and distortion of the
structure and the screen surface may peel off.
When cleaning the power plug pins or dusting the power outlet, clean
it with a dry cloth.
•
Otherwise, it may result in fire.
When cleaning the product, make sure to disconnect the power cord.
•
Otherwise, it may result in electric shock or fire.
When cleaning the product, disconnect the power cord and clean it
with a soft, dry cloth.
•
(Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito repellant, lubricant, or cleaner.) These may change the appearance of the product surface and peel off the indication labels on the
product.
Since the product housing is easily scratched, make sure to use the
specified cloth only.
When cleaning the product, do not spray water directly onto the main
body of the product.
•
Ensure that water does not enter the product and that it is not wet.
•
Otherwise, this may result in electric shock, fire or a malfunction.
Others
The product is a high voltage product. Do not disassemble, repair or
modify the product yourself.
•
Otherwise, this may result in electric shock or fire. If the product
needs to be repaired, contact a Service Center.
If there is a strange smell or a strange sound or smoke is coming from
the product, disconnect the power plug immediately and contact a Service
Center.
•
Otherwise, this may result in electric shock or fire.
Do not place this product in a location exposed to moisture, dust,
smoke, water, or in a car.
•
Otherwise, this may result in electric shock or fire.
Safety Instructions
When you drop the product or the case is broken, turn the power off
and disconnect the power cord. Contact a Service Center.
•
Otherwise, this may result in electric shock or fire.
If thunder or lightning is occurring, do not touch the power cord or
antenna cable.
•
Otherwise, this may result in electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal
cable.
•
Otherwise, it may fall and result in electric shock, damage to the
product or fire due to damage to the cable.
Do not lift or move the product back and forwards or right and left
while only holding the power cord or signal cables.
•
Otherwise, it may fall and result in electric shock, damage to the
product or fire due to damage to the cable.
Make sure that the ventilating opening is not blocked by a table or
curtain.
•
Otherwise, it may result in fire due to an increase in the internal temperature.
Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product.
•
If water or a foreign material enters the product, disconnect the power
cord and contact a Service Center.
•
This may result in a product malfunction, electric shock, or fire.
Do not use or keep combustible spray or flammable material near the
product.
•
Otherwise, this may result in an explosion or fire.
Do not insert any metal, such as chopsticks, coins, pins and steel, or
flammable objects, such as matches or paper, inside the product (through
the ventilating openings, input and output terminals, etc).
•
If water or foreign material enters the product, disconnect the power
cord and contact a Service Center.
•
Otherwise, this may result in electric shock or fire.
When using a fixed screen for a long time, an afterimage or stain may
occur.
•
If you are not using your product for a long period of time, put it into
sleep mode or use a moving screen saver.
Set a resolution and frequency appropriate to the product.
•
Otherwise, your eyesight may be damaged.
Safety Instructions
When using headphones or earphones, do not turn the volume too high.
•
Having the sound too loud may damage your hearing.
To avoid eyestrain, do not sit too close to the product.
Take a rest for at least five (5) minutes after using the monitor for one
(1) hour.
This reduces eye fatigue.
Do not install it in an unstable location such as an unstable rack or
uneven surface or a location exposed to vibrations.
•
Otherwise, it may fall and cause personal injury and/or damage the
product.
•
If you use the product in a location exposed to vibrations, it may
damage the product and result in fire.
When moving the product, turn the power off and disconnect the power
plug, antenna cable, and all the cables connected to the product.
•
Otherwise, it may result in electric shock or fire.
Ensure that children do not hang onto the product or climb up onto the
product.
•
The product may fall and cause personal injury or death.
If you do not use the product for a long period of time, disconnect the
power cord from the power outlet.
•
Otherwise, this may result in overheating or fire due to dust, and may
result in fire due to electric shock or leakage.
Do not place any heavy items or toys or confectionery, such as cookies
etc. that may attract the attention of children and to the product.
•
Your children may hang onto the product causing it to fall and this
may result in personal injury or death.
Be careful that children do not place the battery in their mouths when
removed from the remote control. Place the battery in a location that
children or infants cannot reach.
•
If children have had the battery in their mouths, consult your doctor
immediately.
When replacing the battery, insert it with the right polarity (+, -).
•
Otherwise, the battery may become damaged or it may cause fire,
personal injury or damage due to leakage of the internal liquid.
Safety Instructions
Use only the specified standardized batteries, and do not use a new
battery and a used battery at the same time.
•
Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage of the internal liquid.
The batteries (and rechargeable batteries) are not ordinary refuse and
must be returned for recycling purposes. The customer is responsible for
returning the used or rechargeable batteries for recycling.
•
The customer can return used or rechargeable batteries to a nearby
public recycling center or to a store selling the same type of the battery
or rechargeable battery.
Do not place the product in a location exposed to direct sunlight or
near any heat such as a fire or heater.
•
This may reduce the lifetime of the product, and may result in fire.
Do not drop any objects onto the product or cause any impact to the
product.
•
Otherwise, this may result in electric shock or fire.
Do not use a humidifier near the product.
•
Otherwise, this may result in electric shock or fire.
When there is a gas leak, do not touch the product or the power plug;
ventilate immediately.
•
If a spark occurs, it may cause an explosion or fire.
If the product has been turned on for a long time, the display panel
becomes hot. Do not touch it.
Keep the small accessories in a location out of the reach of children.
Be careful when adjusting the angle of the product or the height of the
stand.
•
This may result in personal injury as your hand or fingers may become caught.
•
Also, if you tilt the product too far, it may fall and cause personal
injury.
Do not install the product in a location low enough for children to
reach.
•
Otherwise, it may fall and result in personal injury.
•
Since the front part of the product is heavy, install the product on a
level and stable surface.
Safety Instructions
Do not put any heavy objects on the product.
•
This may result in personal injury and/or damage to the product.
Precautions when handling the panel
Do not stand the product as shown in the image.
The panel is fragile and can get damaged.
Lay the product down to handle it as shown in the image.
(the packaging can be used).
Ensure you use the handles on the back when moving
the product.
Do not hold or grasp any area of the product within
15mm from the front.
Introduction
Package Contents
Checking the Contents of the Package
Remove the lock from the package box, as shown in the figure above.
Lift up the package box by
holding the grooves on both
sides of the package box.
Check the contents of the
package.
Remove the Styrofoam and
vinyl cover.
Note
•
After unpacking the package, make sure to check the contents of the package.
•
Store the packaging box in case you need to move the Product later.
•
If any items are missing, contact your dealer.
•
Contact a local dealer to purchase optional items.
Unpacking
LCD Display
Introduction
Manuals
Quick Setup Guide
Warranty Card
User Manual
(Not available in all locations)
Cables
Power Cord
D-Sub Cable
Remote Control
Batteries (AAA X 2)
Holder Guide(4EA)
(BP59-00138B)
(Not available in all locations)
(For Video Wall) /
Holder-Ring (4EA) /
Screw (1EA)
Bracket decoration
Screw (4EA)
(For function knob)
(top, bottom, Left, Right)
Others
Screw (8EA)
Screw (16EA)
Sold separately
Semi Stand KIT
Wall Mount KIT
TV Tuner Box
Introduction
Sold separately
RGB to BNC Cable
RGB to Component Cable
Network Box
HDMI to HDMI Cable
Stereo Cable
AV Cable
Display Port Cable
Note
Accessories that can be purchased with the product vary by country.
Your LCD Display
Front
Remote Control Sensor
Aim the remote control towards this spot on the LCD Display.
Light sensor
Automatically detects the intensity of ambient light around a selected display and
adjusts the screen brightness.
Introduction
Power indicator
Shows PowerSaver mode by blinking green
Note
See PowerSaver described in the manual for further information regarding power
saving functions. For energy conservation, turn your LCD Display OFF when it
is not needed or when leaving it unattended for long periods.
POWER button
Use this button for turning the LCD Display on and off.
SOURCE button
Switches from PC mode to Video mode. Selects the input source that an external
device is connected to.
[PC] → [DVI] → [AV] → [Component] → [HDMI1] → [HDMI2] → [DisplayPort] → [MagicInfo] → [TV]
Note
•
A TV tuner box (sold separately) must be connected to use the TV.
•
MagicInfo can only be enabled when a network box is connected.
Function knob
The function knob has a remote-control sensor, a light sensor and function keys. If mounting the display
onto a wall, you can move the function knob to the side of the display.
Default location of the function knob on the display upon purchase
Attaching the knob to the side
Introduction
Attaching the function knob to the display
•
The function knob can be attached to any screw hole on the display.
•
Align the screw holes of the display and function knob. Next, fasten using the screw.
Note
Using a screw other than the one supplied can damage the display.
Detaching the function knob
Hold the area marked in the
picture.
Push the areas marked.
Hold the areas marked, and
lift the function knob.
Rear
Note
See the "Connections" section for details about cable connections. The LCD Display's configuration
at the back may vary slightly depending on the model.
IR OUT
Receives a signal from the remote control and
outputs the signal through Loopout when a removable sensor board is connected.
CONTROL IN
Connects to the function (Power/Source) control
buttons and receives the light sensor signal and
remote control's IR signal.
DVI OUT (LOOPOUT)
Introduction
•
Connect a monitor to another monitor through
a DVI, DVI to HDMI cable.
•
Connect a DVI or DVI-HDMI cable to [DVI
OUT (LOOPOUT)] on the product and [DVI
IN] or [HDMI IN] on another monitor.
•
HDMI and network signals sent via the [DVI
OUT(LOOPOUT)] port are displayed on the
second display which has the [DVI IN] port.
Note
•
The Loopout function can be used to duplicate
the screen of the primary display. Connect
[DVI OUT] on the primary display to [DVI
IN] or [HDMI] on another display.
•
A maximum of 100 monitors can be connected to DVI-Loopout (using a 2m-long DVI
cable). Up to HD resolution can be supported.
Compatible input sources include DVI IN,
HDMI IN 1, and HDMI IN 2 (MagicInfo).
•
The status of the cable may have a great effect
on the Loopout performance.
RGB/COMPONENT IN (PC/COMPONENT
Connection Terminal (Input))
•
Connect the [RGB/COMPONENT IN] port
on the monitor to the RGB port on the PC using the D-SUB cable.
•
Connect the [RGB/COMPONENT IN] port
on the monitor to the COMPONENT port on
the external device using the RGB to COMPONENT cable.
•
Connect the [RGB/COMPONENT IN] port
on the monitor to the BNC port on the PC using the RGB to BNC cable.
DVI IN (PC Video Connection Terminal)
Connect the [DVI IN] port on the monitor to the
DVI port on the PC using the DVI cable.
RGB/DVI/DP/HDMI AUDIO IN (PC/DVI/
DP/HDMI Audio Connection Terminal (Input))
Connect the [RGB/DVI/DP/HDMI AUDIO IN]
terminal of the monitor and the speaker output
terminal of your computer's sound card using a
stereo cable (sold separately).
DP IN
Introduction
Receives a signal from the Display port.
Connect a DP cable to [DP IN] on the product and
DP IN on another display.
AV/COMPONENT AUDIO IN [R-AUDIO-L]
Connect the [AV/COMPONENT AUDIO IN [RAUDIO-L]] port on the monitor to the audio
output port on the PC or on the external device
using an audio cable.
AV IN
Connect the [AV IN] terminal of your monitor to
the video output terminal of the external device
using a VIDEO cable.
AUDIO OUT
Connect a headphone or an External speaker.
DC OUT
Make sure to use connecting [DC OUT] terminal
to the authorized TV-Tuner Box[SBB_DTC/
ZA].
Otherwise, this may result in damage to
the product.
HDMI IN 1
•
Connect the [HDMI IN 1] terminal at the back
of your LCD Display to the HDMI terminal
of your digital output device using a HDMI
cable.
•
Up to HDMI 1.3 can be supported.
Note
•
A normal external device (DVD player or
camcorder, etc.) or a TV tuner box can be
connected to the [HDMI IN 1] terminal.
•
To use a TV tuner box, make sure to connect
it to the [HDMI IN 1] terminal.
HDMI IN 2 (MAGICINFO)
•
Connect the [HDMI IN 2 (MAGICINFO)]
terminal at the back of your LCD Display to
the HDMI terminal of your digital output device using a HDMI cable.
Introduction
•
Up to HDMI 1.3 can be supported.
Note
The MAGICINFO OUT port must be connected
to the [HDMI IN 2 (MAGICINFO)] port.
RJ 45 MDC (MDC PORT)
MDC(Multiple Display Control) Program Port
Connect the LAN cable to [RJ45 MDC] on the
product and LAN on the PC. To use an MDC, the
MDC program must be installed on the PC.
Note
Go to Multi Control and select RJ45 MDC as
the MDC Connection.
RS232C OUT/IN (RS232C Serial PORT)
MDC(Multiple Display Control) Program Port
Connect a serial cable (cross type) to [RS232C]
on the product and RS232C on the PC. To use an
MDC, the MDC program must be installed on the
PC.
Note
Go to Multi Control and select RS232C MDC
as the MDC Connection.
POWER S/W ON [
] / OFF
Switches the LCD Display On/Off.
POWER
The power cord plugs into the LCD Display and
the wall outlet.
Introduction
Kensington Lock slot
An anti-theft lock allows you to use the product
securely even in public places. The locking device shape and locking method depend on the
manufacturer. Refer to the user guide provided
with your anti-theft locking device for details.
To lock the product, follow these steps:
1.
Fix the cable of your anti-theft locking device to a heavy object such as a desk.
2.
Put one end of the cable through the loop on
the other end.
3.
Insert the locking device into the anti-theft
lock slot at the back of the product.
4.
Lock the locking device.
Note
•
An anti-theft locking device can be purchased
separately.
•
Refer to the user guide provided with your
anti-theft locking device for details.
•
Anti-theft locking devices can be purchased
at electronics retailers or online.
Note
See the "Connections" section for details about cable connections.
Remote Control
Note
The performance of the remote control may be affected by a TV or other electronic device operating
near the LCD Display , causing a malfunction due to interference with the frequency.
Introduction
POWER
OFF
Number Buttons
DEL
/ GUIDE button
+ VOL SOURCE
D.MENU
TOOLS
Up-Down Left-Right buttons
INFO
The Color button and the PC/DVI/HDMI/DP
selection button
TTX/MIX
MTS/DUAL
ENTER/PRE-CH
MUTE
CH/P
TV
MENU
RETURN
EXIT
MagicInfo
POWER
Turns the product On.
Turns the product Off.
OFF
Number Buttons
Used to enter the password during the OSD adjustment or to use
MagicInfo.
Press to change the channel.
DEL
/ GUIDE button
The "-" button is used to select Digital channels.
Electronic Program Guide (EPG) display.
- This function does not work for this LCD Display.
+ VOL SOURCE
Adjusts the audio volume.
Selects a connected external input source or MagicInfo mode.
Press the button to change the input signal SOURCE.
Introduction
Changing the SOURCE is only allowed for external devices that
are connected to the LCD Display at the time.
D.MENU
DTV menu display
- This function does not work for this LCD Display.
TOOLS
Use to quickly select frequently used functions.
- This function does not work for this LCD Display.
Up-Down Left-Right buttons
INFO
The Color button and the
PC/DVI/HDMI/DP selection
button
TTX/MIX
Moves from one menu item to another horizontally, vertically or
adjusts selected menu values.
Current picture information is displayed on the upper left corner
of the screen.
In TV mode, these buttons can be used for setting the broadcasting
announcement function of a digital channel.
You can select the PC, DVI, HDMI or DP(DisplayPort) external
input directly in a mode other than TV mode.
TV channels provide written information services via teletext.
- Teletext Buttons
- This is activated when a TV tuner box is installed.
MTS/DUAL
MTSYou can select MTS (Multichannel Television Stereo) mode.
FM Stereo
Audio Type
MTS/S_Mode
Default
Mono
Mono
Manual Change
Stereo
Mono ↔ Stereo
SAP
Mono ↔ SAP
Mono
DUALSTEREO/MONO, DUAL l / DUAL ll and MONO/NICAM
MONO/NICAM STEREO can be operated depending on the
broadcasting type by using the DUAL button on the remote control
while watching TV.
- This is activated when a TV tuner box is installed.
ENTER/PRE-CH
This button is used to return to the immediately previous channel.
- This is activated when a TV tuner box is installed.
MUTE
CH/P
Pauses (mutes) the audio output temporarily. This is displayed on
the lower left corner of the screen. The audio comes back on if
MUTE or - VOL + is pressed in the Mute mode.
In TV mode, selects TV channels.
- This is activated when a TV tuner box is installed.
Introduction
Selects the TV mode directly.
TV
- This is activated when a TV tuner box is installed.
MENU
RETURN
EXIT
MagicInfo
Opens the on-screen menu and exits from the menu or closes the
adjustment menu.
Returns to the previous menu.
Exits from the menu screen.
MagicInfo Quick Launch Button.
Note
This button is disabled for products that do not support MagicInfo.
Attaching the holders
•
Fix the holders into
s on the back of the product using the screws.
When displays are connected to form a video wall, the holders will make the gap between displays
uniform on all four sides.
Introduction
Instructions on how to attach the decoration brackets
Decoration
Decoration
Decoration
bracket - top bracket - bottom
For a 3x3 video wall
Screws
bracket - left side bracket - right side (FH, M4*L10 x
16)
Attaching the decoration brackets
For a single display
Decoration
Introduction
•
To attach the decoration brackets to the sides of a video wall or Samsung UD installed, remove the
stickers from the screw holes first.
Note
•
Do not remove the stickers if you do not want to attach the decoration brackets.
•
To attach the decoration brackets to a 3x3 video wall, ensure you connect all the displays before
attaching the brackets.
User Installation Guide
Note
•
Be sure to call an installation expert of Samsung Electronics to install the product.
•
The warranty becomes invalid if the product is installed by someone other than a professional
authorized by Samsung Electronics.
•
A Samsung Electronics service center can provide details.
Tilt Angle and Rotation
Introduction
1
2
1.
The product can be tilted up to 15 degrees from a vertical wall.
2.
To use the product in portrait mode, rotate it clockwise so that the LED indicator is at the bottom.
Ventilation requirement
1. Vertical wall mount condition
<Side view>
A : min. 40 mm
B: Ambient temperature Measuring point < 35°C
•
When installing the product onto a vertical wall, be sure there is a 40 mm space or more behind
the product for ventilation, as shown above, and maintain the ambient temperature at 35°C or lower.
Note
A Samsung Electronics service center can provide details.
2. Embedded Mount guide
<Side view>
<Top view>
Introduction
A : min. 40 mm
B : min. 70 mm
C : min. 50 mm
D : min. 50 mm
E : Ambient temperature Measuring point < 35°C
•
When embedding the product in a wall, be sure there is some space behind the product for ventilation, as shown above, and maintain the ambient temperature at 35°C or lower.
Note
A Samsung Electronics service center can provide details.
3. Floor mount guide
<Side view>
A : min. 50 mm
B: Ambient temperature Measuring point < 20°C
•
When embedding the product in the floor, be sure there is a 50 mm space or more behind the product
for ventilation, as shown above, and maintain the ambient temperature at 20 °C or lower.
Note
A Samsung Electronics service center can provide details.
Introduction
Dimensions (unit:mm)
Dimensions (unit:mm)
Notice
•
All drawings are not necessarily to scale. Some dimensions are subject to change without prior
notice.
•
For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm
length.
Introduction
Installing the Wall Mount
Preparing before installing Wall-Mount
To install a wall-mount from another manufacturer, use
the Holder-Ring.
Installing the Wall Mount Kit
The wall mount kit (sold separately) allows you to mount the product on the wall. For detailed information on installing the wall mount, see the instructions provided with the wall mount items. Contact
a technician for assistance when installing the wall mount bracket. Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the Wall
mount on your own.
Wall Mount Kit Specifications (VESA)
Note
Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building
materials, please contact your nearest dealer. If you install the product on a ceiling or slanted wall, it
may fall and result in severe personal injury.
Note
•
Standard dimensions for wall mount kits are shown
in the table below.
•
When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly
are provided.
•
Do not use screws that do not comply with the VESA
standard screw specifications. Screws that are too
long may cause damage to the inside of the product
set.
•
For wall mounts that do not comply with the VESA
standard screw specifications, the length of the
screws may differ depending on the wall mount specifications.
•
Do not fasten the screws too tightly, as this may damage the product or cause the product to fall, leading
to personal injury. Samsung is not liable for these
kinds of accidents.
•
Samsung is not liable for product damage or personal
injury when a non-VESA or non-specified wall
mount is used or the consumer fails to follow the
product installation instructions.
Introduction
•
Do not mount the product at more than a 15 degree
tilt.
•
Always have two people to mount the product to a
wall.
Model name
VESA Spec.(A * B)
Standard Screw
Quantity
UD55A
600 x 400
M8
4EA
Caution
Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury
due to electric shock.
Remote Control (RS232C)
Cable connections
interface
RS232C(9 pin)
pin
TxD(No.2) RxD(No.3) GND(No.5)
Bits rate
9600 bps
Data Bits
8 bit
Parity
None
Stop Bits
1 bit
Flow control
None
Maximum length
15 m (only shielded type)
•
Pin assignment
Pin
Signal
1
Data Carrier Detect
2
Received Data
3
Transmitted Data
4
Data Terminal Ready
5
Signal Ground
6
Data Set Ready
7
Request to Send
8
Clear to Send
9
Ring Indicator
Introduction
•
RS232C cable
Connector : 9-pin D-Sub
Cable : Cross (reversed) cable
-P1FEMALE
•
-P1-
-P2-
-P2-
Rx
2
--------->
3
Rx
Tx
3
<---------
2
Tx
Gnd
5
----------
5
Gnd
FEMALE
Connecting method
Control codes
•
•
•
Get control
Header
command
0xAA
command type
DATA Length
ID
0
CheckSum
Set control
Header
command
0xAA
command
type
ID
DATA
Length
DATA
1
Value
CheckSum
commanding words
No.
command type
command
Value range
Introduction
1
Power control
0x11
0~1
2
Volume control
0x12
0~100
3
Input source control
0x14
-
4
Screen Mode control
0x18
-
5
Screen Size control
0x19
0~255
6
PIP on/off control
0x3C
0~1
7
Auto adjustment control
0x3D
0
8
Video wall Mode control
0x5C
0~1
9
Safety Lock
0x5D
0~1
- ID should show hexadecimal value of assigned ID, but ID 0 should be 0xFF.
- Every communication will be made in hexadecimals and Checksum is the sum of all remainings.
If it exceeds two digits,for example, it is 11+FF+01+01=112, discard the number in the first digit
like below.
example)PowerOn&ID=0
Header
command
ID
DATA
Length
DATA 1
CheckSum
0xAA
0x11
1
Power
Header
command
DATA
Length
DATA 1
0xAA
0x11
1
1
ID
12
If you want to control every mechanism connected with Serial Cable regardless of its ID, set ID
part to "0xFE" and send commands. At the time, each product will follow commands but it will
not respond with ACK.
•
Power Control
•
Function
Personal Computer turns TV / Monitor power ON/OFF.
•
•
Get Power ON/OFF Status
Header
command
0xAA
0x11
DATA Length
ID
0
CheckSum
Set Power ON/OFF
Header
command
0xAA
0x11
ID
Power : Power code to be set on TV / Monitor
1 : Power ON
0 : Power OFF
DATA
Length
DATA
1
Power
CheckSum
Introduction
•
Ack
Header
command
0xAA
0xFF
ID
DATA
Length
Ack/Nak
r-CMD
Val1
3
‘A’
0x11
Power
DATA
Length
Ack/Nak
r-CMD
Val1
3
‘N’
0x11
ERR
Check
Sum
Power : Same as above
•
Nak
Header
command
0xAA
0xFF
ID
Check
Sum
ERR : Error code that shows what occurred error is
•
Volume Control
•
Function
Personal Computer changes volume of TV / Monitor.
•
•
Get Volume Status
Header
command
0xAA
0x12
DATA Length
ID
CheckSum
0
Set Volume
Header
command
ID
0xAA
DATA
Length
DATA
1
Volume
0x12
CheckSum
Volume : Volume value code to be set on TV / Monitor (0 ~ 100)
•
Ack
Header
command
0xAA
0xFF
ID
DATA
Length
Ack/Nak
r-CMD
Val1
3
‘A’
0x12
Volume
DATA
Length
Ack/Nak
r-CMD
Val1
3
‘N’
0x12
ERR
Check
Sum
Volume : Same as above
•
Nak
Header
command
0xAA
0xFF
ID
ERR : Error code that shows what occurred error is
Check
Sum
Introduction
•
Input Source Control
•
Function
Personal Computer changes input source of TV / Monitor.
•
•
Get Input Source Status
Header
command
0xAA
0x14
DATA Length
ID
CheckSum
0
Set Input Source
Header
command
ID
0xAA
0x14
DATA
Length
DATA
1
Input Source
CheckSum
Input Source : Input Source code to be set on TV / Monitor
0x14
PC
0x1E
BNC
0x18
DVI
0x0C
AV
0x04
S-Video
0x08
Component
0x20
MagicInfo
0x1F
DVI_VIDEO
0x30
RF(TV)
0x40
DTV
0x21
HDMI1
0x22
HDMI1_PC
0x23
HDMI2
0x24
HDMI2_PC
0x25
DisplayPort
Caution
DVI_VIDEO, HDMI1_PC, HDMI2_PC → Get Only
In the case of MagicInfo, only possible with models include MagicInfo
In the case of TV, only possible with models include TV.
•
Ack
Header
command
ID
DATA
Length
Ack/Nak
r-CMD
Val1
Check
Sum
Introduction
0xAA
3
‘A’
0x14
Input
Source
DATA
Length
Ack/Nak
r-CMD
Val1
3
‘N’
0x14
ERR
0xFF
Input Source : Same as above
•
Nak
Header
command
0xAA
0xFF
ID
Check
Sum
ERR : Error code that shows what occurred error is
•
Screen Mode Control
•
Function
Personal Computer changes "Screen Mode" of TV/Monitor.
Cannot be controlled when Video Wall is on.
Caution
Only works with models include TV.
•
•
Get Screen Mode Status
Header
command
0xAA
0x18
DATA Length
ID
CheckSum
0
Set Picture Size
Header
command
0xAA
0x18
ID
DATA
Length
DATA
1
Screen Mode
CheckSum
Screen Mode : Screen Mode code to be set on TV / Monitor
•
0x01
16 : 9
0x04
Zoom
0x31
Wide Zoom
0x0B
4:3
Ack
Header
command
ID
0xAA
0xFF
Screen Mode : Same as above
DATA
Length
3
Ack/Nak
‘A’
r-CMD
Val1
0x18
Screen
Mode
Check
Sum
Introduction
•
Nak
Header
command
0xAA
0xFF
ID
DATA
Length
Ack/Nak
r-CMD
Val1
3
‘N’
0x18
ERR
Check
Sum
ERR : Error code that shows what occurred error is
•
Screen Size Control
•
Function
Personal Computer recognizes the screen size of TV / Monitor.
•
•
Get Screen Size Status
Header
command
0xAA
0x19
DATA Length
ID
CheckSum
0
Ack
Header
command
ID
0xAA
0xFF
DATA
Length
Ack/Nak
r-CMD
Val1
3
‘A’
0x19
Screen
Size
Check
Sum
Screen Size : Screen Size of TV / Monitor (Range : 0 ~ 255, Unit : Inch)
•
Nak
Header
command
0xAA
0xFF
ID
DATA
Length
Ack/Nak
r-CMD
Val1
3
‘N’
0x19
ERR
Check
Sum
ERR : Error code that shows what occurred error is
•
PIP ON / OFF Control
•
Function
The PC turns the PIP function of a TV or Monitor ON / OFF.
This does not operate in MagicInfo mode.
•
Get the PIP ON / OFF Status
Header
command
0xAA
0x3C
ID
DATA Length
0
CheckSum
Introduction
•
Set the PIP ON / OFF
Header
command
0xAA
0x3C
ID
DATA
Length
DATA
1
PIP
CheckSum
PIP : The PIP ON / OFF code to set for the TV or Monitor
1 : PIP ON
0 : PIP OFF
•
Ack
Header
command
0xAA
0xFF
ID
DATA
Length
Ack/Nak
r-CMD
Val1
3
‘A’
0x3C
PIP
DATA
Length
Ack/Nak
r-CMD
Val1
3
‘N’
0x3C
ERR
Check
Sum
PIP : Same as above
•
Nak
Header
command
0xAA
0xFF
ID
Check
Sum
ERR : Error code that shows what occurred error is
•
Auto Adjustment Control (PC, BNC Only)
•
Function
Personal Computer controls PC system screen automatically.
•
Get Auto Adjustment Status
None
•
Set Auto Adjustment
Header
command
0xAA
0x3D
ID
DATA
Length
DATA
1
Auto Adjustment
CheckSum
Auto Adjustment : 0x00 (Always)
•
Ack
Header
command
ID
DATA
Length
Ack/Nak
r-CMD
Val1
Check
Sum
Introduction
0xFF
3
‘A’
0x3D
Auto Adjustment
Header
command
DATA
Length
Ack/Nak
r-CMD
Val1
0xAA
0xFF
3
‘N’
0x3D
ERR
0xAA
•
Nak
ID
Check
Sum
ERR : Error code that shows what occurred error is
•
Video Wall Mode Control
•
Function
Personal Computer converts Video Wall Mode of TV / Monitor when Video Wall is ON.
Only works with TV / Monitor where Video Wall is on.
Does not operate in MagicInfo
•
•
Get Video Wall Mode
Header
command
0xAA
0x5C
DATA Length
ID
CheckSum
0
Set Video Wall Mode
Header
command
0xAA
0x5C
ID
DATA
Length
DATA
1
Video Wall
Mode
CheckSum
Video Wall Mode : Video Wall Mode code to be set on TV / Monitor
1 : Full
0 : Natural
•
Ack
Header
DATA
Length
command
Ack/Nak
r-CMD
Val1
0x5C
Video
Wall
Mode
ID
0xAA
0xFF
Video Wall Mode : same as above
•
Nak
3
‘A’
Check
Sum
Introduction
Header
command
0xAA
0xFF
ID
DATA
Length
Ack/Nak
r-CMD
Val1
3
‘N’
0x5C
ERR
Check
Sum
ERR : Error code that shows what occurred error is
•
Safety Lock
•
Function
Personal Computer turns Safety Lock function of TV / Monitor ON / OFF.
Can operate regardless of whether power is ON / OFF.
•
•
Get Safety Lock Status
Header
command
0xAA
0x5D
DATA Length
ID
CheckSum
0
Set Safety Lock Enable / Disable
Header
command
ID
0xAA
DATA
Length
DATA
1
Safety Lock
0x5D
CheckSum
Safety Lock : Lock code to be set on TV / Monitor
1 : ON
0 : OFF
•
Ack
Header
command
ID
0xAA
0xFF
DATA
Length
Ack/Nak
r-CMD
Val1
3
‘A’
0x5D
Safety
Lock
DATA
Length
Ack/Nak
r-CMD
Val1
3
‘N’
0x5D
Safety
Lock
Check
Sum
Safety Lock : Same as above
•
Nak
Header
command
ID
0xAA
0xFF
ERR : Error code that shows what occurred error is
Check
Sum
Connections
Connecting a Computer
There are several ways to connect the computer to the monitor. Choose one from
the following options.
Using the D-sub (Analog) connector on the video card.
•
Connect the D-sub to the 15-pin, [RGB/COMPONENT IN] port on the back
of your LCD Display and the 15 pin D-sub Port on the computer.
Using the DVI (Digital) connector on the video card.
•
Connect the DVI Cable to the [DVI IN] port on the back of your LCD Display
and the DVI port on the computer.
Using the HDMI (Digital) connector on the video card.
•
Connect the [HDMI IN 1] port on the LCD Display to the HDMI port on the
PC using the HDMI cable.
Connections
Note
Select HDMI2 or HDMI1 as an input source when connected to the PC via an
HDMI cable.
To obtain normal picture and audio from the PC, HDMI2 or HDMI1 must be
selected before PC is selected in Edit Name.
To enable audio when DVI Device is selected, be sure to establish the connection
using step (
).
Connect the Audio cable for your LCD Display to the Audio port on the back of
the LCD Display.
Connect the power cord for your LCD Display to the Power port on the back of
the LCD Display. Turn on the power switch.
Note
Contact a local SAMSUNG Electronics Service Center to buy optional items.
Connecting to Other devices
Note
•
AV input devices such as DVD players, VCRs or camcorders as well as your computer can be
connected to the LCD Display. For detailed information on connecting AV input devices, refer to
the contents under Adjusting Your LCD Display.
•
The LCD Display 's configuration at the back may vary slightly depending on the LCD Display
model.
Connecting an External Monitor
Connections
Connect between the [DVI OUT(LOOPOUT)] port on the LCD Display and the
input port on another monitor using a DVI cable.
Connect between the [AUDIO OUT] port on the LCD Display and the audio input
port on another monitor using a stereo cable.
Note
Select DVI Mode as an input source for the external monitor connected to [DVI OUT].
DVI OUT does not support HDCP.
Connecting AV Devices
1.
Connect an audio cable to [AV/COMPONENT AUDIO IN [R-AUDIO-L]] on the
product and the audio port on an external device such as a VCR or DVD player.
2.
Connect a video cable to [AV IN] on the product and the video output port on the
external device.
3.
Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted.
4.
Press SOURCE on the product or remote control and select "AV".
Note
AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected
to the LCD Display. For detailed information on connecting AV input devices, refer to the contents
under Adjusting Your LCD Display.
Connections
Connecting to a Camcorder
1.
Locate the AV output jacks on the camcorder. They are usually found on the side
or back of the camcorder. Connect a video cable between the VIDEO OUTPUT
jack on the camcorder and the [AV IN] on the LCD Display .
2.
Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the [AV /COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD
Display .
3.
Press SOURCE on the product or remote control and select "AV".
4.
Then, start the Camcorders with a tape inserted.
Note
The audio-video cables shown here are usually included with a Camcorder.
(If not, check your local electronics store.)
If your camcorder is stereo, you need to connect a set of two cables.
Connecting Using a HDMI Cable
Connections
1.
Connect an HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] on the
product and the HDMI output port on a digital device.
2.
Press SOURCE on the product or remote control and select "HDMI1 / HDMI2"
Note
In HDMI mode, only PCM format audio is supported.
Connecting Using a DVI to HDMI Cable
Connect a DVI-HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] and
the DVI output port on the digital device.
Connect the red and white jacks of an RCA to stereo (for PC) cable to the same
colored audio output terminals of the digital output device, and connect the opposite jack to the [RGB/DVI/DP/HDMI AUDIO IN] terminal of the LCD Display.
3.
Press SOURCE on the product or remote control and select "HDMI1 / HDMI2"
Connecting a DVD Player
Connections
Connect a RGB to Component cable between the [RGB/COMPONENT IN] port
on the LCD Display and the PR, Y, PB jacks on the DVD player.
Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [RAUDIO-L]] on the LCD Display and the AUDIO OUT jacks on the DVD player.
Note
•
Press SOURCE on the product or remote control and select "Component".
•
Then, start the DVD Player with a DVD disc inserted.
•
A RGB to component cable is optional.
•
For an explanation of Component video, consult your DVD manual.
Connecting a DTV Set Top (Cable/Satellite) Box
Connect a RGB to Component cable between the [RGB/COMPONENT IN] port
on the LCD Display and the PR, Y, PB jacks on the Set Top Box.
Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [RAUDIO-L]] on the LCD Display and the AUDIO OUT jacks on the Set Top Box.
Note
•
Press SOURCE on the product or remote control and select "Component".
•
For an explanation of Component video, see your Set Top Box owner's manual.
Connections
Connecting to an Audio System
1.
Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and [AUDIO OUT] on LCD Display.
Using the Software
Monitor Driver
Note
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions appropriate for the operating system you
have.
Prepare a blank disk and download the driver program file at the Internet web site
shown here.
Internet web site :
http://www.samsung.com/
Installing the Monitor Driver (Automatic)
1.
Insert CD into the CD-ROM drive.
2.
Click "Windows".
3.
Choose your monitor model in the model list, then click the "OK" button.
4.
If you can see following message window, then click the "Continue Anyway" button. Then click
"OK" button (Microsoft® Windows® XP/2000 Operating System).
Using the Software
Note
This monitor driver is certified by Microsoft, and installing it will not damage your system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
Installing the Monitor Driver (Manual)
Microsoft® Windows Vista™‚ Operating System
1.
Insert your Manual CD into your CD-ROM drive.
2.
Click
3.
Click "Personalization" and then "Display Settings".
4.
Click "Advanced Settings...".
5.
Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the
configuration for your monitor is completed. The monitor can be used as is.
(Start) and "Control Panel". Then, double-click on "Appearance and Personalization".
If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue".
Using the Software
Note
This monitor driver is under certifying MS logo, and this installation will not damage your system.
The certified driver will be posted on Samsung Monitor homepage.
6.
Click "Update Driver..." in the "Driver" tab.
7.
Check the "Browse my computer for driver software" checkbox and click "Let me pick from a
list of device drivers on my computer".
8.
Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup file is
located, and click "OK".
Using the Software
9.
Select the model that matches your monitor from the list of monitor models on the screen, and
click "Next".
10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Microsoft® Windows® XP Operating System
Using the Software
1.
Insert CD into the CD-ROM drive.
2.
Click "Start" → "Control Panel", then click the "Appearance and Themes" icon.
3.
Click "Display" icon and choose the "Settings" tab then click "Advanced...".
4.
Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
5.
Click "Update Driver..." and select "Install from a list or..." then click "Next" button.
6.
Select "Don't search, I will...", then click "Next" and then click "Have disk".
Using the Software
7.
Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model
list and click the "Next" button.
8.
If you can see the following message window, then click the "Continue Anyway" button. Then
click "OK" button.
Note
This monitor driver is certified by Microsoft, and this installation will not damage your system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
9.
Click the "Close" button, then click the "OK" button continually.
Using the Software
10. Monitor driver installation is completed.
Microsoft® Windows® 2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1.
Choose "OK" button on the "Insert disk" window.
2.
Click the "Browse" button on the "File Needed" window.
3.
Choose A:(D:\Driver), then click the "Open" button and then click "OK" button.
How to install
1.
Click "Start", "Setting", "Control Panel".
2.
Double click the "Display" icon.
3.
Select the "Settings" tab and click "Advanced Properties" button.
4.
Choose "Monitor".
Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please
stop installation
Case2 : If the "Properties" button is active, click the "Properties" button, then follow the next
steps.
5.
Click "Driver" and then click on "Update Driver...", then click on the "Next" button.
6.
Choose "Display a list of the known drivers for this device so that I can choose a specific driver",
then click "Next" and then click "Have disk".
7.
Click the "Browse" button, then choose A:(D:\Driver).
8.
Click the "Open" button, then click "OK" button.
9.
Choose your monitor model and click the "Next" button. Then click "Next" button.
10. Click the "Finish" button, then the "Close" button.
If you can see the "Digital Signature Not Found" window, then click the "Yes" button. Then click
the "Finish" button and the "Close" button.
Microsoft® Windows® Millennium Operating System
1.
Click "Start", "Setting", "Control Panel".
2.
Double click the "Display" icon.
3.
Select the "Settings" tab and click "Advanced Properties" button.
Using the Software
4.
Select the "Monitor" tab.
5.
Click the "Change" button in the "Monitor Type" area.
6.
Choose "Specify the location of the driver".
7.
Choose "Display a list of all the driver in a specific location...", then click "Next" button.
8.
Click the "Have Disk" button.
9.
Specify A:\(D:\driver), then click "OK" button.
10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to
your computer and click "OK".
11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.
Microsoft® Windows® NT Operating System
1.
Click "Start", "Settings", "Control Panel", and then double-click "Display" icon.
2.
In Display Registration Information window, click Settings Tab and then click "All Display
Modes".
3.
Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and
then click "OK".
4.
Click "Apply" button if you see the screen working normally after clicking "Test". If the screen
is not normal, change to a different mode (lower mode of resolution, colors or frequency).
Note
If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by
referring to the Preset Timing Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting file.
1.
Press "Enter" at the first and the second screen after executing the X86Config file.
2.
The third screen is for setting your mouse.
3.
Set a mouse for your computer.
4.
The next screen is for selecting a keyboard.
5.
Set a Keyboard for your computer.
6.
The next screen is for setting your monitor.
7.
First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.)
8.
Set a vertical frequency for your monitor. (You can enter the frequency directly.)
9.
Enter the model name of your monitor. This information will not affect the actual execution of
X-Window.
10. You have finished setting up your monitor. Execute X-Window after setting other requested
hardware.
Using the Software
MDC (Multiple Display Control)
Installation
1.
Insert the installation CD into the CD-ROM drive.
2.
Click the MDC System installation program.
Note
If the screen for installing the software does not appear, install it using the MDC System execution
file in the MDC folder of the CD-ROM.
3.
If the installation wizard screen does appear, click "Next."
4.
The "License Agreement" screen will appear. Click "Yes."
5.
The "Customer Information" window will appear. Register the user information and click "Yes."
6.
The "Choose Destination Location" window will appear. Specify the file location to install to and
click "Next."
Note
If the file location is not specified, the program will be installed in the default file location.
7.
The "Start Copying Files" window will appear. Confirm the file location and click "Next."
8.
The installation progress screen will appear.
9.
The "InstallShield Wizard Complete" screen will appear. Click "Finish."
Note
Select " Launch MDC System" and click "Finish." The MDC program will immediately be run.
10. If the installation is successfully completed, the quick MDC System execution icon will appear
on the desktop.
MDC execution icon may not appear depending on specification of computer system or
monitor. If that happens, press F5 Key.
Installation Problems
The installation of MDC can be affected by such factors as the video card, motherboard and the network
environment.
Using the Software
Uninstall
The MDC program can be removed only by using the "Add or Remove Programs" option of the
Windows® Control Panel.
Perform the following steps remove MDC.
Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program".
Select MDC System from the list and then click the "Add/Delete" button.
Using Serial MDC
Using Ethernet MDC
S e r i a l MDC
Introduction
A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously
operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and
a display. Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a
display.
Main Screen
Click Start > Program > Samsung > MDC System to start the program.
Select a set to see the volume of the selected set within the slider.
Main Icons
All
Remote control
Selection Buttons
Safety Lock
Refresh
Port Selection
Display Selection
Lamp Control
Info Grid
Option...
Control Tools
Dropdown Selectors
OSD Display
1.
Use the main icons to switch into each screen.
2.
Allows you to enable or disable the remote control signal receiving function of the display unit.
3.
Set the Safety Lock function.
When setting the Lock function, you can only operate power and lock buttons on the remote control and set.
4.
The setting for the PC Serial Port can change. The original value is COM1.
5.
Selects a Lamp adjustment mode.
6.
Adjusts the number of LFD IDs and the frequency of search repeats.
7.
Defines the range of LFD IDs to display. You can select or deselect the displayed IDs using the Select or Clear
button.
8.
All of the monitors can be selected or deselected.
9.
Selects (Select) or deselects (Clear) LFD IDs displayed by configuring 7 and 8.
10. This searches for monitors. The maximum number is indicated in the Max LFD Id field.
11. Select a display from Display Selection.
12. Use Grid to view brief information on selected display.
13. Use Control Tools to control displays.
14. Switches the OSD function On/Off.
- May not be supported depending on the product.
<Note> The remote control Enable/Disable function operates whether or not the power is On/Off, and this
applies to all displays connected to the MDC. However, regardless of the status at the time the MDC is
shut down, the remote control signal receiving function of all displays is initialized to Enable when the
MDC is closed.
Port Selection
1. The Multiple Display Control is originally set to COM1.
2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu.
3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will
be unavailable.
4. The selected port is stored in the program and used for the next program as well.
System
1. Click System in the main menu to open the system adjustment screen.
Info Grid shows some basic information necessary to System.
1)
(Power Status)
2) Input
3) Image Size
4) On Timer
5) Off Timer
2. Selects displays you want to adjust using the Select button or checkboxes.
System allows controlling some of the functions of the selected display.
1) Power On/Off
- Turns the power of the selected display On/Off.
2) Volume
- Controls the volume level of the selected display.
It receives the volume value of the selected display from the sets and displays it in the slider.
(If you deselect a single display or all displays, the default value 10 will be restored.)
3)
(Mute On/Off)
- Turns on/off the Mute function of the selected display.
When selecting one set at a time, turn on the Mute function for the selected set.
The Mute function is disabled automatically when you adjust the volume level.
(The values return to the default settings when you undo the selections or choose "Select All".)
The Volume Control and Mute features are available only for the displays whose power status is ON.
3. Selects whether to display the menu screen using the OSD Display menu.
1) Source OSD
- Sets whether the Source OSD will be displayed to indicate when the Source is changed.
2) Not Optimum Mode OSD
- Sets whether the Optimum Mode OSD will be displayed to indicate if the current mode is not supported.
3) No Signal OSD
- Sets whether the No Signal OSD will be displayed to indicate when there is no signal.
4) MDC OSD
- Sets whether the MDC OSD will be displayed to indicate when the settings are changed using the MDC.
Input Source
1. Click Input Source of the main icons and the Input Source control screen appears.
Selects displays you want to adjust using the Select button or checkboxes.
• TV Mode
• PC Mode
Info Grid shows some basic information necessary to Input Source Control.
1)
PC
- Changes the Input Source of the selected display to PC.
2)
BNC
- Changes the Input Source of the selected display to BNC.
3)
DVI
- Changes the Input Source of the selected display to DVI.
4)
TV
- Changes the Input Source of the selected display to TV.
5)
DTV
- Changes the Input Source of the selected display to DTV.
6)
AV
- Changes the Input Source of the selected display to AV.
7)
S-Video
- Changes the Input Source of the selected display to S-Video.
8)
Component
- Changes the Input Source of the selected display to Component.
9)
MagicInfo
- The Input source of MagicInfo works only on MagicInfo model.
10)
HDMI1/HDMI2
- Changes the Input Source of the selected display to HDMI.
11)
DP
- Switches the input source for the selected Display to DP.
12)
Channel
- Channel arrow appears when the Input Source is TV.
HDMI2 may not be supported depending on the product.
DP may not be supported depending on the product.
TV Source can be selected only in products with TV and controlling channels is allowed only when
Input Source is TV.
The Input Source Control feature is available only for the displays whose power status is ON.
Image Size
PC, BNC, DVI, DP
1. Click Image Size of the main icons and the Image Size control screen appears.
Info Grid shows some basic information necessary to Image Size Control.
1)
( Power Status)
- Shows the power status of the current display.
2) Image Size
- Shows the current Image Size of the display in use.
3) Input
- Info Grid displays only the displays whose Input Source is PC, BNC, DVI and DP.
4) PC Source
- Click Image Size in the main menu to display the PC, BNC, DVI and DP tabs.
- The Image Size Control button controls Image Size available for PC, BNC, DVI and DP.
5) Video Source
- Using the Image Size adjustment button, you can adjust the Image Size to a value available in the PC, BNC, DVI
and DP.
DP may not be supported depending on the product.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Image Size Control is available only for the displays for which power status is ON.
Image Size
TV, AV, S-Video, Component, DVI(HDCP), HDMI1, HDMI2, DTV.
1. Click Image Size of the main icons and the Image Size control screen appears.
Info Grid shows some basic information necessary to Image Size Control.
1) To adjust Image Size in TV, AV, S-Video, Component, HDMI1, HDMI2 or DTV mode, click the Video Source tab.
Select the display you want to adjust by using the Select button or by checking the checkbox.
2) Info Grid displays only the display having TV, AV, S-Video, Component, HDMI1, HDMI2 or DTV as input source.
3) Switch Image Size of the selected display randomly.
4) The screen modes can only be adjusted when a TV (PAL only) is connected and the Image Size item is set to Auto
Wide.
HDMI2 may not be supported depending on the product.
Custom may not be supported depending on the product.
Auto Wide, Zoom1 and Zoom2 are not available for selection when the input signal type for Component
and DVI (HDCP) is 720p or 1080i.
(The Auto Wide mode is available only for TV, AV, and S-Video.)
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
The Image Size Control feature is available only for the displays whose power status is ON.
Time
1. Click Time of the main icons and the Time Control screen appears.
Info Grid shows some basic information necessary to Time Control.
1) Set clock
- Set the current time for the selected display (PC Time).
- To change the current time, first change the PC Time.
2) Timer
- Sets up Timer1, Timer2, Timer3 and Holiday Management.
3) Shows whether Timer is activated.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Time Control is available only for the displays for which the power status is ON.
Time
Setting up Timer and Holiday Management
1. 1. Setting up Timer1, Timer2 and Timer3
1) On Time
- Sets the time in hours, in minutes and as AM/PM for turning the selected monitor on.
2) Off Time
- Sets the time in hours, in minutes and as AM/PM for turning the selected monitor off.
3) Volume
- Selects the volume when the selected monitor is turned on.
4) Source
- Selects the external input source that will be displayed when the selected monitor is turned on.
5) Holiday
- Applies the Holiday Management function to the Timer.
6) Repeat
- Available selections include Once, EveryDay, Mon~Fri, Mon~Sat, Sat~Sun, and Manual.
z
z
z
z
z
z
Once : The Timer goes off only once.
EveryDay : EveryDay: The Timer repeats daily.
Mon~Fri : The Timer repeats from Monday through Friday.
Mon~Sat : The Timer repeats from Monday through Saturday.
Sat~Sun : The Timer repeats from Saturday to Sunday
Manual : Select a day of the week you want the Timer to go off.
2. Setting Holiday Management
The Holiday Management function specifies the dates in which the monitor will not be turned on or off by the Timer.
1) Specifies the date.
2) Delete All
- Deletes all of the holidays.
3) Add
- Adds the specified date.
4)
- Deletes the schedule in the selected line.
The Holiday Management function can be turned on or off in the Timer setup menu.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Time Control is available only for the displays for which the power status is ON.
Only enabled for a TV when Source is set to TV in On Time mode.
Only enabled for a model with MagicInfo installed when Source is set to MagicInfo in On Time mode.
PIP
PIP Size
1. Click PIP of the main icons and the PIP control screen appears.
Selects displays you want to adjust using the Select button or checkboxes.
Info Grid shows some basic information necessary to PIP Size Control.
1) PIP Size
- Shows the current PIP Size of the display in use.
2) OFF
- Turns off the PIP of the selected display.
3) Large
- Turns on the PIP of the selected display and changes the size to Large.
4) Small
- Turns on the PIP of the selected display and changes the size to Small.
5) Double 1
- Turns on the PIP of the selected display and changes the size to Double 1.
6) Double 2
- Turns on the PIP of the selected display and changes the size to Double 2.
7) Double 3 (Picture By Picture)
- Turns on the PBP of the selected display and changes the size to Double 3.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
PIP Size can be controlled with turning on the LCD Display power.
PIP
PIP Source
1. Click PIP of the main icons and the PIP control screen appears.
Info Grid shows some basic information necessary to PIP Source Control.
1) PIP Source
- PIP Source can be controlled with turning on the LCD Display power.
2) PC
- Changes the source of the PIP of the selected display to PC.
3) BNC
- Changes the source of the PIP of the selected display to BNC.
4) DVI
- Changes the source of the PIP of the selected display to DVI.
5) TV
- Changes the source of the PIP of the selected display to TV.
6) DTV
- Changes the source of the PIP of the selected display to DTV.
7) AV
- Changes the source of the PIP of the selected display to AV.
8) S-Video
- Changes the source of the PIP of the selected display to S-Video.
9) Component
- Changes the source of the PIP of the selected display to Component.
10) HDMI1/HDMI2
- Changes the source of the PIP of the selected display to HDMI.
11) DP
- Switches the PIP Source of the selected Display to DP.
HDMI2 may not be supported depending on the product.
DP may not be supported depending on the product.
Some of the PIP Sources may not be available for selection, depending on the input source type of the
Main Screen.
The Input source of MagicInfo works only on MagicInfo model.
The PIP Control feature is available only for the displays whose power status is ON and the PIP
function is set to ON.
Settings
Picture
1. Click Settings of the main icons and the Settings Control screen appears.
Basic information required to adjust the Picture is displayed in the main menu. Settings for the selected monitor will
be displayed if one of the connected monitors is selected, and the default settings will be displayed if all monitors
are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically
switch to custom mode.
1) Picture
- Available only for TV, AV, S-Video, Component, HDMI1, HDMI2, DTV.
2) Contrast
- Adjusts Contrast of the selected display.
3) Brightness
- Adjusts Brightness of the selected display.
4) Sharpness
- Adjusts Sharpness of the selected display.
5) Color
- Adjusts Color of the selected display.
6) Tint
- Adjusts Tint of the selected display.
- Available only for NTSC.
7) Color Tone
- Adjusts the Color Tone for the selected display.
8) Color Temp
- Adjusts the Color Temp for the selected display.
9) Brightness Sensor
- Adjusts the Brightness Sensor for the selected display.
10) Dynamic Contrast
- Adjusts the Dynamic Contrast for the selected display.
HDMI2 may not be supported depending on the product.
Brightness Sensor may not be supported depending on the product.
The Input source of MagicInfo works only on MagicInfo model.
Color Temp is only enabled if the Color Tone is set to Off.
The Input source of TV works only on TV model.
This feature is available only for the displays whose power status is ON and if no selection is made, the
factory default is displayed.
Settings
Picture PC
1. Click Settings of the main icons and the Settings Control screen appears.
Basic information required to adjust settings is displayed. Settings for the corresponding SET will be imported and
displayed on the slider if a display ID is selected, and the default settings will be displayed if all display IDs are
selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically switch to
custom mode.
1) Picture PC
- Available only for PC, BNC, DVI and DP.
2) Contrast
- Adjusts Contrast of the selected display.
3) Brightness
- Adjusts Brightness for the selected display.
4) Red
- Adjusts red Color of the selected display.
- Available only for NTSC.
5) Green
- Adjusts green Color of the selected display.
- Available only for NTSC.
6) Blue
- Adjusts blue Color of the selected display.
- Available only for NTSC.
7) Color Tone
- Adjusts the Color Tone for the selected display.
8) Color Temp
- Adjusts the Color Temp for the selected display.
9) Brightness Sensor
- Adjusts the Brightness Sensor for the selected display.
10) Dynamic Contrast
- Adjusts the Dynamic Contrast for the selected display.
DP may not be supported depending on the product.
Brightness Sensor may not be supported depending on the product.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Color Temp is only enabled if the Color Tone is set to Off.
This feature is available only for the displays whose power status is ON and if no selection is made, the
factory default is displayed.
Settings
Audio
1. Click Settings of the main icons and the Settings Control screen appears.
Basic information required to adjust Audio is displayed in the display window. Settings for the corresponding SET will
be imported and displayed on the slider if a display ID is selected, and the default settings will be displayed if all
display IDs are selected by clicking All and Select. If a value is changed in this screen, the current mode will
automatically switch to custom mode.
1) Audio
- Controls audio settings for all input sources.
2) Bass
- Adjusts Bass of the selected display.
3) Treble
- Adjusts Treble of the selected display.
4) Balance
- Adjusts Balance of the selected display.
5) SRS TS XT
- SRS TS XT Sound ON/OFF of the selected display.
6) Sound Select
- Select either Main or Sub when PIP is On.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
This feature is available only for the displays whose power status is ON and if no selection is made, the
factory default is displayed.
Settings
Image Lock
1. Click Settings of the main icons and the Settings Control screen appears.
Info Grid shows some basic information necessary to Settings Control.
1) Image Lock
- Available only for PC, BNC.
2) Coarse
- Adjusts Coarse of the selected display.
3) Fine
- Adjusts Fine of the selected display.
4) Position
- Adjusts Position of the selected display.
5) Auto Adjustment
- Self-Adjust to the incoming PC signal.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Settings Control is available only for the displays for which the power status is ON.
Maintenance
Lamp Control
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
An "Info Grid" showing several basic data items appears.
1) Maintenance
- Allows the Maintenance Control function for all input sources.
2) Lamp Control
- Automatically adjusts the backlight of the selected display at a specified time.
The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control.
- Allows you to adjust the backlight of the selected display regardless of the time.
The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control.
3) Ambient Light
- Detects the ambient light intensity at the designated monitor and automatically adjusts the picture brightness.
- You can specify a Reference value and designate a monitor that will automatically determine Lamp Value (the light
intensity from the lamp), based on the ambient light intensity.
Ambient Light is only supported for models that have a brightness sensor and is only enabled when
Ambient Brightness Mode is selected in the Lamp Control menu.
Auto Lamp Control and Manual Lamp Control are only enabled when User Control Mode is selected in
the Lamp Control menu.
The Maintenance Control feature is available only for the displays whose power status is ON.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Maintenance
Scroll
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
1) Scroll
- This function is used to remove the afterimages that occur when a still screen is displayed on the selected
display
for a long time.
2) Pixel Shift
- This allows the screen to be moved finely at the specified time interval.
3) Safety Screen
- The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the
monitor for a long time. The Interval item is used to set the repetition cycle in hour units and the Time item is
used to set the time when the Safety Screen function must be performed.
The Type item can be set to Scroll, Pixel, Bar, Eraser, All White, or Pattern.
4) Safety Screen2
- This function is used to prevent afterimages from occurring. There are five (5) types that you can select and
control with this function.
For the Scroll type, the Time item can be set to 1, 2, 3, 4 or 5. For the Bar and Eraser types, it can be set
to 10, 20, 30, 40 or 50. For the All White and Pattern type, it can be set to 1, 5, 10, 20 or 30.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
The Maintenance Control feature is available only for the displays whose power status is ON.
Maintenance
Video Wall
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
1) Video Wall
- A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole
picture or so that the same picture is repeated on each screen.
2) Video Wall Control
- Video Wall properties can be configured.
1) On / Off
- Turns on/off the Video Wall function of the selected display.
2) Format
- The format can be selected to see a divided screen.
z
Full
z
Natural
3) Video Wall (Screen divider)
- The screen can be divided into.
You can select a number of screens with a different layout when dividing.
z Select a mode from Screen divider.
z Select a display from Display Selection.
z The place will be set up by pressing a number in the selected mode.
z The maximum number of monitors that can be arranged: Horizontal X Vertical = 100
z Up to 15 monitors can be arranged in a row. The maximum value for Horizontal is 6 if Vertical is set to 15 while
the maximum value for Vertical is 6 if Horizontal is set to 15.
4) Viewing Screen Splits
- You can view and change the layout of screens using the Screen Divider settings.
The range of the Screen Divider setting may differ depending on the model.
You may not operate this function in MagicInfo.
The Input source of TV works only on TV model.
The Maintenance Control function is available only for the displays where the power status is ON.
Troubleshooting
1. The display you wish to control does not appear on the System Info Grid
- Check the connection of RS232C. (Check if it is properly connected to the Com1 port
- Check the displays to see if any of the other displays connected have the same ID. If more than one displays have
the same ID, those displays are not properly detected by the program due to data conflict.
- For monitors that support a Set ID between 0 to 99, you have to set the Set ID to a value between 0 and 99.
Note :
Check if the Set ID of the monitor is a value between 0 and 99 (set the value using the Display menu).
2. The display you wish to control does not appear on the other Control Info Grids
- Check to see if the display power is ON. (You can check this in System Info Grid)
- Check if you can change the input source of the display.
3. The dialogue box appears repeatedly.
- Check to see if the display you wish to control is selected.
4. Both On Timer and Off Timer have been set but different time is showing.
- Apply current time to synchronize the display clocks.
5. The remote may not function properly when you turn off the remote Function, disconnect the RS-232C cable, or exit
the program in an Irregular manner. Rerun the program and turn the remote function again to Restore normal
functions.
<Note> This program may malfunction due to problems in communication circuits or interference from electronic
appliances nearby.
Settings Value Display In Multiple Display Mode
When there are more than one displays connected, the settings values are displayed as follows.
1. No selection: Displays the Factory Default Value.
2. Selected one display: Fetches and displays the settings value for the selected display.
3. Selected one display (ID1) and add another display (ID3): The program, which was displaying the settings value of
ID 1, fetches and displays the value of ID3.
4. If all sets are selected at the same time by clicking All and Select, the default value will be restored.
Ehternet MDC
Introduction
Unlike the previous method which used the serial data communication specifications RS-232C, an Ethernet
function has been added.
Connect the first display device and the PC by entering the IP address. To connect to another display device,
use an RS-232C serial cable. Refer to the figure above.
Main Screen
Click Start > Program > Samsung > MDC System to start the program.
Select a set to see the volume of the selected set within the slider.
Main Icons
Lamp Control
Add a Device
Display Selection
Remote Control
All
Safety Lock
Control Tools
Fault Device Alert
OSD Display
1.
Use the main icons to switch into each screen.
2.
You can add a device by entering the IP address configured on the monitor.
3.
Allows you to enable or disable the remote control signal receiving function of the display unit.
4.
Set the Safety Lock function.
When setting the Lock function, you can only operate power and lock buttons on the remote control and set.
5.
When connecting to the monitor fails, it turns the function that transfers the result through an email on or off.
6.
Selects a Lamp adjustment mode.
7.
Select a display from Display Selection.
8.
All of the monitors can be selected or deselected.
9.
Use Control Tools to control displays.
10. Switches the OSD function On/Off.
- May not be supported depending on the product.
<Note> The remote control Enable/Disable function operates whether or not the power is On/Off, and this
applies to all displays connected to the MDC. However, regardless of the status at the time the
MDC is shut down, the remote control signal receiving function of all displays is initialized to
Enable when the MDC is closed.
Add a Device
1. Enter the IP address of the monitor to be connected and press the Add button to add the IP address. If you
click the OK button, adding the monitor is completed.
System
1. Click System in the main menu to open the system adjustment screen.
Info Grid shows some basic information necessary to System.
1)
(Power Status)
2) Input
3) Image Size
4) On Timer
5) Off Timer
2. Selects displays you want to adjust using the Select All button or checkboxes.
System allows controlling some of the functions of the selected display.
1) Power On/Off
- Turns the power of the selected display On/Off.
2) Volume
- Controls the volume level of the selected display.
It receives the volume value of the selected display from the sets and displays it in the slider.
(If you deselect a single display or all displays, the default value 10 will be restored.)
3)
(Mute On/Off)
- Turns on/off the Mute function of the selected display.
When selecting one set at a time, turn on the Mute function for the selected set.
The Mute function is disabled automatically when you adjust the volume level.
(The values return to the default settings when you undo the selections or choose "Select All".)
The Volume Control and Mute features are available only for the displays whose power status is
ON.
3. Selects whether to display the menu screen using the OSD Display menu.
1) Source OSD
- Sets whether the Source OSD will be displayed to indicate when the Source is changed.
2) Not Optimum Mode OSD
- Sets whether the Optimum Mode OSD will be displayed to indicate if the current mode is not supported.
3) No Signal OSD
- Sets whether the No Signal OSD will be displayed to indicate when there is no signal.
4) MDC OSD
- Sets whether the MDC OSD will be displayed to indicate when the settings are changed using the MDC.
Network
1) Select or clear all the added devices; or refresh or delete selected devices.
2) The IP Address, ID (Ethernet or Serial), Mac Address and connection status of the connected monitor is displayed.
3) It can automatically check whether DHCP IP is set and then set the IP address.
4) It can automatically or manually set and then apply the IP Address, Subnet and Gateway of the selected monitor.
Input Source
1)
Click Input Source of the main icons and the Input Source control screen appears.
Selects displays you want to adjust using the Select All button or checkboxes.
• TV Mode
• PC Mode
Info Grid shows some basic information necessary to Input Source Control.
1) PC
- Changes the Input Source of the selected display to PC.
2) BNC
- Changes the Input Source of the selected display to BNC.
3) DVI
- Changes the Input Source of the selected display to DVI.
4) TV
- Changes the Input Source of the selected display to TV.
5) DTV
- Changes the Input Source of the selected display to DTV.
6) AV
- Changes the Input Source of the selected display to AV.
7) S-Video
- Changes the Input Source of the selected display to S-Video.
8) Component
- Changes the Input Source of the selected display to Component.
9) MagicInfo
- The Input source of MagicInfo works only on MagicInfo model.
10) HDMI1/HDMI2
- Changes the Input Source of the selected display to HDMI.
11) DP
- Switches the input source for the selected display to DP.
12) Channel
- Channel arrow appears when the Input Source is TV.
HDMI2 may not be supported depending on the product.
DP may not be supported depending on the product.
The Input Source Control feature is available only for the displays whose power status is ON.
TV Source can be selected only in products with TV and controlling channels is allowed only when
Input Source is TV.
Image Size
PC, BNC, DVI, DP
1. Click Image Size of the main icons and the Image Size control screen appears.
Info Grid shows some basic information necessary to Image Size Control.
1)
( Power Status)
- Shows the power status of the current display.
2) Image Size
- Shows the current Image Size of the display in use.
3) Input
- Info Grid displays only the displays whose Input Source is PC, BNC, DVI and DP.
4) PC Source
- Click Image Size in the main menu to display the PC, BNC, DVI and DP tabs.
- The Image Size Control button controls Image Size available for PC, BNC, DVI and DP.
5) Video Source
- Click the Video Source tab to control Image Size for respective Input Source.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Image Size Control is available only for the displays for which power status is ON.
DP may not be supported depending on the product.
Image Size
TV, AV, S-Video, Component, DVI(HDCP), HDMI1, HDMI2, DTV
1. Click Image Size of the main icons and the Image Size control screen appears.
Info Grid shows some basic information necessary to Image Size Control.
1) To adjust Image Size in TV, AV, S-Video, Component, HDMI1, HDMI2 or DTV mode, click the Video Source
tab.
Select the display you want to adjust by using the Select All button or by checking the checkbox.
2) Info Grid displays only the display having TV, AV, S-Video, Component, HDMI1, HDMI2 or DTV as input source.
3) Switch Image Size of the selected display randomly.
4) The screen modes can only be adjusted when a TV (PAL only) is connected and the Image Size item is set to
Auto Wide.
Custom may not be supported depending on the product.
Auto Wide, Zoom1 and Zoom2 are not available for selection when the input signal type for
Component and DVI (HDCP) is 720p or 1080i.
(The Auto Wide mode is available only for TV, AV, and S-Video.)
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
The Image Size Control feature is available only for the displays whose power status is ON.
HDMI2 may not be supported depending on the product.
Time
1. Click Time of the main icons and the Time Control screen appears.
Info Grid shows some basic information necessary to Time Control.
1) Clock Set
- Set the current time for the selected display (PC Time).
- To change the current time, first change the PC Time.
2) Timer
- Sets up Timer1, Timer2, Timer3 and Holiday Management.
3) Shows whether Timer is activated.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Time Control is available only for the displays for which the power status is ON.
Time
Setting up Timer and Holiday Management
1. Setting up Timer1, Timer2 and Timer3
1) On Time
- Sets the time in hours, in minutes and as AM/PM for turning the selected monitor on.
2) Off Time
- Sets the time in hours, in minutes and as AM/PM for turning the selected monitor off.
3) Volume
- Selects the volume when the selected monitor is turned on.
4) Source
- Selects the external input source that will be displayed when the selected monitor is turned on.
5) Holiday
- Applies the Holiday Management function to the Timer.
6) Repeat
- Available selections include Once, EveryDay, Mon~Fri, Mon~Sat, Sat~Sun, and Manual.
z
z
z
z
z
z
Once : The Timer goes off only once.
EveryDay : EveryDay: The Timer repeats daily.
Mon~Fri : The Timer repeats from Monday through Friday.
Mon~Sat : The Timer repeats from Monday through Saturday.
Sat~Sun : The Timer repeats from Saturday to Sunday
Manual : Select a day of the week you want the Timer to go off.
2. Setting Holiday Management
The Holiday Management function specifies the dates in which the monitor will not be turned on or off by the
Timer.
1) Specifies the date.
2) Delete All
- Deletes all of the holidays.
3) Add
- Adds the specified date.
4)
- Deletes the schedule in the selected line.
The Holiday Management function can be turned on or off in the Timer setup menu.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Time Control is available only for the displays for which the power status is ON.
Only enabled for a TV when Source is set to TV in On Time mode.
Only enabled for a model with MagicInfo installed when Source is set to MagicInfo in On Time
mode.
PIP
PIP Size
1. Click PIP of the main icons and the PIP control screen appears.
Selects displays you want to adjust using the Select All button or checkboxes.
Info Grid shows some basic information necessary to PIP Size Control.
1) PIP Size
- Shows the current PIP Size of the display in use.
2) OFF
- Turns off the PIP of the selected display.
3) Large
- Turns on the PIP of the selected display and changes the size to Large.
4) Small
- Turns on the PIP of the selected display and changes the size to Small.
5) Double 1
- Turns on the PIP of the selected display and changes the size to Double 1.
6) Double 2
- Turns on the PIP of the selected display and changes the size to Double 2.
7) Double 3 (Picture By Picture)
- Turns on the PBP of the selected display and changes the size to Double 3.
PIP Size can be controlled with turning on the LCD Display power.
The Input source of TV works only on TV model.
The Input source of MagicInfo works only on MagicInfo model.
PIP
PIP Source
1. Click PIP of the main icons and the PIP control screen appears.
Info Grid shows some basic information necessary to PIP Source Control.
1) PIP Source
- PIP Source can be controlled with turning on the LCD Display power.
2) PC
- Changes the source of the PIP of the selected display to PC.
3) BNC
- Changes the source of the PIP of the selected display to BNC.
4) DVI
- Changes the source of the PIP of the selected display to DVI.
5) TV
- Changes the source of the PIP of the selected display to TV.
6) DTV
- Changes the source of the PIP of the selected display to DTV.
7) AV
- Changes the source of the PIP of the selected display to AV.
8) S-Video
- Changes the source of the PIP of the selected display to S-Video.
9) Component
- Changes the source of the PIP of the selected display to Component.
10) HDMI1/HDMI2
- Changes the source of the PIP of the selected display to HDMI.
11) DP
- Switches the PIP Source of the selected Display to DP.
Some of the PIP Sources may not be available for selection, depending on the input source type
of the Main Screen.
The PIP Control feature is available only for the displays whose power status is ON and the PIP
function is set to ON.
HDMI2 may not be supported depending on the product.
DP may not be supported depending on the product.
The Input source of MagicInfo works only on MagicInfo model.
HDMI2 may not be supported depending on the product.
Setting
Picture
1. Click Settings of the main icons and the Settings Control screen appears.
Basic information required to adjust the Picture is displayed in the main menu. Settings for the selected
monitor will be displayed if one of the connected monitors is selected, and the default settings will be
displayed if all monitors are selected by clicking All and Select. If a value is changed in this screen, the current
mode will automatically switch to custom mode.
1) Picture
- Available only for TV, AV, S-Video, Component, HDMI1, HDMI2, DTV.
2) Contrast
- Adjusts Contrast of the selected display.
3) Brightness
- Adjusts Brightness of the selected display.
4) Sharpness
- Adjusts Sharpness of the selected display.
5) Color
- Adjusts Color of the selected display.
6) Tint
- Adjusts Tint of the selected display.
- Available only for NTSC.
7) Color Tone
- Adjusts the Color Tone for the selected display.
8) Color Temp
- Adjusts the Color Temp for the selected display.
9) Brightness Sensor
- Adjusts the Brightness Sensor for the selected display.
10) Dynamic Contrast
- Adjusts the Dynamic Contrast for the selected display.
Brightness Sensor may not be supported depending on the product.
The Input source of MagicInfo works only on MagicInfo model.
Color Temp is only enabled if the Color Tone is set to Off.
The Input source of TV works only on TV model.
This feature is available only for the displays whose power status is ON and if no selection is
made, the factory default is displayed.
HDMI2 may not be supported depending on the product.
Setting
Picture PC
1. Click Settings of the main icons and the Settings Control screen appears.
Basic information required to adjust settings is displayed. Settings for the corresponding SET will be imported
and displayed on the slider if a display ID is selected, and the default settings will be displayed if all display IDs
are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically
switch to custom mode.
1) Picture PC
- Available only for PC, BNC, DVI and DP.
2) Contrast
- Adjusts Contrast of the selected display.
3) Brightness
- Adjusts Brightness for the selected display.
4) Red
- Adjusts red Color of the selected display.
- Available only for NTSC.
5) Green
- Adjusts green Color of the selected display.
- Available only for NTSC.
6) Blue
- Adjusts blue Color of the selected display.
- Available only for NTSC.
7) Color Tone
- Adjusts the Color Tone for the selected display.
8) Color Temp
- Adjusts the Color Temp for the selected display.
9) Brightness Sensor
- Adjusts the Brightness Sensor for the selected display.
10) Dynamic Contrast
- Adjusts the Dynamic Contrast for the selected display.
Brightness Sensor may not be supported depending on the product.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Color Temp is only enabled if the Color Tone is set to Off.
This feature is available only for the displays whose power status is ON and if no selection is
made, the factory default is displayed
DP may not be supported depending on the product.
Setting
Audio
1. Click Settings of the main icons and the Settings Control screen appears.
Basic information required to adjust Audio is displayed in the display window. Settings for the corresponding
SET will be imported and displayed on the slider if a display ID is selected, and the default settings will be
displayed if all display IDs are selected by clicking All and Select. If a value is changed in this screen, the
current mode will automatically switch to custom mode.
1) Audio
- Controls audio settings for all input sources.
2) Bass
- Adjusts Bass of the selected display.
3) Treble
- Adjusts Treble of the selected display.
4) Balance
- Adjusts Balance of the selected display.
5) SRS TS XT
- SRS TS XT Sound ON/OFF of the selected display.
6) Sound Select
- Select either Main or Sub when PIP is On.
This feature is available only for the displays whose power status is ON and if no selection is
made, the factory default is displayed.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Setting
Image Lock
1. Click Settings of the main icons and the Settings Control screen appears.
Info Grid shows some basic information necessary to Settings Control.
1) Image Lock
- Available only for PC, BNC.
2) Coarse
- Adjusts Coarse of the selected display.
3) Fine
- Adjusts Fine of the selected display.
4) Position
- Adjusts Position of the selected display.
5) Auto Adjustment
- Self-Adjust to the incoming PC signal.
The Maintenance Control feature is available only for the displays whose power status is ON.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Maintenance
Lamp Control
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
An "Info Grid" showing several basic data items appears.
1) Maintenance
- Allows the Maintenance Control function for all input sources.
2) Lamp Control
- Automatically adjusts the backlight of the selected display at a specified time.
The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control.
- Allows you to adjust the backlight of the selected display regardless of the time.
The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control.
3) Ambient Light
- Detects the ambient light intensity at the designated monitor and automatically adjusts the picture
brightness.
- You can specify a Reference value and designate a monitor that will automatically determine Lamp Value
(the light intensity from the lamp), based on the ambient light intensity.
Ambient Light is only supported for models that have a brightness sensor and is only enabled
when Ambient Brightness Mode is selected in the Lamp Control menu.
Auto Lamp Control and Manual Lamp Control are only enabled when User Control Mode is
selected in the Lamp Control menu.
The Maintenance Control feature is available only for the displays whose power status is ON.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Maintenance
Scroll
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
1) Scroll
- This function is used to remove the afterimages that occur when a still screen is displayed on the selected
display for a long time.
2) Pixel Shift
- This allows the screen to be moved finely at the specified time interval.
3) Safety Screen
- The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on
the monitor for a long time. The Interval item is used to set the repetition cycle in hour units and the Time
item is used to set the time when the Safety Screen function must be performed.
The Type item can be set to Scroll, Pixel, Bar, Eraser, All White, or Pattern.
4) Safety Screen2
- This function is used to prevent afterimages from occurring. There are five (5) types that you can select and
control with this function.
For the Scroll type, the Time item can be set to 1, 2, 3, 4 or 5. For the Bar and Eraser types, it can be
set to 10, 20, 30, 40 or 50. For the All White and Pattern type, it can be set to 1, 5, 10, 20 or 30.
The Maintenance Control feature is available only for the displays whose power status is ON.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Maintenance
Video Wall
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
1) Video Wall
- A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the
whole picture or so that the same picture is repeated on each screen.
2) Video Wall Control
- Video Wall properties can be configured.
1) On / Off
- Turns on/off the Video Wall function of the selected display.
2) Format
- The format can be selected to see a divided screen.
z
Full
z
Natural
3) Video Wall (Screen divider)
- The screen can be divided into.
You can select a number of screens with a different layout when dividing.
z Select a mode from Screen divider.
z Select a display from Display Selection.
z The place will be set up by pressing a number in the selected mode.
z The maximum number of monitors that can be arranged: Horizontal X Vertical = 100
z Up to 15 monitors can be arranged in a row. The maximum value for Horizontal is 6 if Vertical is set to 15
while the maximum value for Vertical is 6 if Horizontal is set to 15.
4) Viewing Screen Splits
- You can view and change the layout of screens using the Screen Divider settings.
The range of the Screen Divider setting may differ depending on the model.
You may not operate this function in MagicInfo.
The Input source of TV works only on TV model.
The Maintenance Control function is available only for the displays where the power status is ON.
Troubleshooting
1. The display you wish to control does not appear on the System Info Grid
- Check if the entered IP address is correct and check the connection status of the Ethernet cable.
- Check the displays to see if any of the other displays connected have the same ID. If more than one displays
have the same ID, those displays are not properly detected by the program due to data conflict.
- For monitors that support a Set ID between 0 to 99, you have to set the Set ID to a value between 0 and 99.
Note :
Check if the Set ID of the monitor is a value between 0 and 99 (set the value using the Display
menu).
2. The display you wish to control does not appear on the other Control Info Grids
- Check to see if the display power is ON. (You can check this in System Info Grid)
- Check if you can change the input source of the display.
3. The dialogue box appears repeatedly.
- Check to see if the display you wish to control is selected.
4. Both On Timer and Off Timer have been set but different time is showing.
- Apply current time to synchronize the display clocks.
5. The remote may not function properly when you turn off the remote Function, disconnect the Ethernet cable, or
exit the program in an Irregular manner. Rerun the program and turn the remote function again to Restore normal
functions.
<Note> This program may malfunction due to problems in communication circuits or interference from electronic
appliances nearby.
Settings Value Display In Multiple Display Mode
When there are more than one displays connected, the settings values are displayed as follows.
1. No selection: Displays the Factory Default Value.
2. Selected one display: Fetches and displays the settings value for the selected display.
3. Selected one display (ID1) and add another display (ID3): The program, which was displaying the settings
value of ID 1, fetches and displays the value of ID3.
4. If all sets are selected at the same time by clicking All and Select, the default value will be restored.
Adjusting the LCD Display
Input
Available Modes
•
PC / DVI / DisplayPort
•
AV
•
Component
•
HDMI
•
MagicInfo
•
TV
Note
•
A TV tuner box (sold separately) must be connected to use the TV.
•
MagicInfo can only be enabled when a network box is connected.
Source List
Use to select PC, HDMI or other external input sources connected to the LCD Display. Use to select
the screen of your choice.
1.
PC
2.
DVI
3.
AV
4.
Component
5.
HDMI1 - This is deactivated when a TV tuner box is installed.
6.
HDMI2 - This is deactivated when a network box is installed.
7.
DisplayPort
8.
MagicInfo - This menu is activated when a network box is connected.
9.
TV - Activated when a TV tuner box is connected.
Note
The RGB/COMPONENT IN port is compatible with RGB (PC) and Component signals.
Adjusting the LCD Display
However, the picture may display abnormally if the connected external input signal is different
from the selected video signal.
PIP
Note
The PIP function is not available when Video Wall is On.
When external AV devices such as VCRs or DVDs are connected to the LCD Display , PIP allows
you to watch video from those devices in a small window super-imposed on the PC Video signal.
(Off/On)
Note
•
PIP turns off when the LCD Display is switched to an external source.
•
If you select
,
,
in Size, Position and Transparency will not be activated.
PIP
Turns the PIP Screen Off/On.
•
Off
•
On
Source
Note
PIP is disabled if the primary screen does not receive a signal.
A TV tuner box (sold separately) must be connected to use the TV.
Selects the input source for the PIP.
•
PC : DVI / AV / HDMI1 / HDMI2 / DisplayPort
•
DVI : PC
•
AV : PC
Adjusting the LCD Display
•
HDMI : PC
•
Display Port : PC
Size
Changes the Size of the PIP window.
Note
Size will be changed to 16:9 when PIP is On.
Position
Changes the Position of the PIP window.
Transparency
Adjusts the Transparency of PIP windows.
•
High
•
Medium
•
Low
•
Opaque
Adjusting the LCD Display
Edit Name
Name the input device connected to the input jacks to make your input source selection easier.
VCR / DVD / Cable STB / HD STB / Satellite STB / AV Receiver / DVD Receiver / Game /
Camcorder / DVD Combo / DHR / PC / DVI PC / DVI Devices
Note
•
The displayed devices differ depending on the external input mode.
•
When connecting a PC to the HDMI terminal, set Edit Name to PC. In other cases, set Edit
Name to AV. However, since 640x480, 720P (1280x720), and 1080p (1920x1080) are common
signals for AV and PC, make sure to set the Edit Name in accordance with the input signal.
•
The Picture menu changes depending on the input signal and Edit Name.
When using a DVI to HDMI cable connection (which does not support audio and video at the same
time), the audio port should be connected via a separate audio cable.
When a PC is connected, set Edit Name to DVI PC to enjoy the video and audio from the connected
PC.
When an AV device is connected, set Edit Name to DVI Device to enjoy the video and audio from
the connected AV device.
Source AutoSwitch Settings
Turning on the display with Source AutoSwitch On, and the previous video source selection is not
active, the display will automatically search the different video input sources for active video.
Note
•
If the display TV source is active (TV tuner connected to the display) the Source AutoSwitch
search function becomes inactive. The display will remain in the TV source.
•
Source AutoSwitch selection and PIP function: If the Source AutoSwitch selection is set to
On, the PIP function will not work, the Source AutoSwitch selection must be set to Off, for the
PIP feature to work.
•
When the Source AutoSwitch selection is On, and or the Primary Source Recovery is On, the
display power saving mode becomes inactive.
•
When Primary Source Recovery is On, only the Primary Source and Secondary Source selection are available and they are interchangeable and selectable at will.
Refer to PIP > Source for compatible signals for each primary input source.
Adjusting the LCD Display
Source AutoSwitch
When the Source AutoSwitch is On, the display video source will automatically be searched for active
video.
The Primary Source selection will be activated, if the current video source is not recognized. Secondary source selection will become active, if no primary video source is available. If the primary or
secondary source is not recognized, the display will search again, if no active video is found the display
will show the no-input-signal message.
When the Primary Source selection is set to All, the display will search all the video source inputs
twice in sequence looking for an active video source, returning back to the first video source in the
sequence if no video is found.
1.
Off
2.
On
Primary Source Recovery
When Primary Source Recovery is On, only the Primary Source and Secondary Source video
source selection will be searched for active video.
The Primary Source will be selected if active video is found, if no video is found, the Secondary
Source will be selected, if no video is found in Secondary Source again, the no-input-signal is displayed.
1.
Off
2.
On
Primary Source
Adjusting the LCD Display
Specify Primary Source for the automatic input source.
Secondary Source
Specify Secondary Source for the automatic input source.
Picture [PC / DVI / DisplayPort / MagicInfo Mode]
Available Modes
•
PC / DVI / DisplayPort
•
AV
•
Component
•
HDMI
•
MagicInfo
•
TV
Note
•
A TV tuner box (sold separately) must be connected to use the TV.
•
MagicInfo can only be enabled when a network box is connected.
Mode
Note
Not available when Dynamic Contrast is set to On.
1.
Information
Recommended for communicating exact information (e.g. public information).
2.
Advertisement
Adjusting the LCD Display
Recommended for displaying advertisements (e.g. videos or indoor or outdoor ads).
3.
Custom
Custom
By using the on-screen menus, the contrast and brightness can be changed to your personal preference.
Note
•
By adjusting the picture using the Custom function, MagicBright will change to Custom mode.
•
Not available when Dynamic Contrast is set to On.
1.
Contrast
Adjusts the Contrast.
2.
Brightness
Adjusts the Brightness.
3.
Sharpness
Adjusts the Sharpness.
4.
Gamma
Adjust the mid-range brightness (Gamma) for the picture.
•
Natural
•
Mode 1
Sets the picture brighter than Natural.
•
Mode 2
Sets the picture darker than Mode 1.
•
Mode 3
Increases the contrast between dark and bright colors.
Adjusting the LCD Display
Color Tone
Note
Not available when Dynamic Contrast is set to On.
The color tones can be changed.
1.
Off
2.
Cool
3.
Normal
4.
Warm
5.
Custom
Note
If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp. function is disabled.
If you set the Color Tone to Off, the Color Control function is disabled
Color Control
Adjusts individual Red, Green, Blue color balance.
Note
Not available when Dynamic Contrast is set to On.
1.
Red
2.
Green
3.
Blue
Color Temp.
Color Temp. is a measure of the 'warmth' of the image colors.
Adjusting the LCD Display
Note
•
Not available when Dynamic Contrast is set to On.
•
This function is only enabled if the Color Tone is set to Off.
Image Lock
Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images
with jitters and shakiness. If satisfactory results are not obtained using the Fine adjustment, use the
Coarse adjustment and then use Fine again.
Note
Available in PC mode only.
Coarse
Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may
relocate it to the center using the horizontal control menu.
Fine
Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after
adjusting the frequency (clock speed).
Position
Adjusts the screen location horizontally and vertically.
Auto Adjustment
The values of Fine, Coarse, Position are adjusted automatically. By changing the resolution in the
control panel, the auto function is performed.
Note
Available in PC mode only.
Signal Balance
This is used to make up for the weak RGB signal transmitted by a long signal cable.
Adjusting the LCD Display
Note
•
Not available when Dynamic Contrast is set to On.
•
Available in PC mode only.
Signal Balance
Selects either On or Off with the signal balance.
Signal Control
Note
Available when Signal Balance is set to On.
1.
R-Gain
2.
G-Gain
3.
B-Gain
4.
R-Offset
5.
G-Offset
6.
B-Offset
Adjusting the LCD Display
Size
The Size can be switched.
1.
16:9
2.
4:3
PIP Picture
Adjusts the PIP Screen Settings.
Note
•
1.
Available Modes: PIP On
Contrast
Adjusts the Contrast of the PIP window on the screen.
2.
Brightness
Adjusts the Brightness of the PIP window on the screen.
3.
Sharpness
Adjusts the Sharpness of the PIP window on the screen.
4.
Color
Adjusts the Color of the PIP window on the screen.
Note
PIP input only operates in DVI, AV, HDMI, or Component mode.
5.
Tint
Adds a natural tone to the PIP window.
Adjusting the LCD Display
Note
PIP input only operates in DVI, AV, HDMI, or Component mode.
Dynamic Contrast
Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an
optimum contrast.
1.
Off
2.
On
Note
Disabled when PIP is set to On.
Lamp Control
Adjusts the inverter lamp in order to reduce energy consumption.
Note
Not available when Dynamic Contrast is set to On.
Brightness Sensor
Brightness Sensor detects the surrounding light intensity and automatically optimizes the screen
brightness accordingly.
1.
Off
2.
On
Adjusting the LCD Display
Uniformity Enhancer
Make the screen brightness even throughout the whole screen.
1.
Off
2.
On
Picture Reset
Reset the screen settings.
Picture [ AV / HDMI / Component / TV Mode]
Available Modes
•
PC / DVI / DisplayPort
•
AV
•
Component
•
HDMI
•
MagicInfo
•
TV
Note
Mode
•
A TV tuner box (sold separately) must be connected to use the TV.
•
MagicInfo can only be enabled when a network box is connected.
Adjusting the LCD Display
The LCD Display has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory.
Dynamic, Standard, Movie, or Custom can be activated.
Note
Not available when Dynamic Contrast is set to On.
1.
Dynamic
2.
Standard
3.
Movie
4.
Custom
Custom
By using the on-screen menus, the contrast and brightness can be changed to your personal preference.
Note
Not available when Dynamic Contrast is set to On.
Contrast
Adjusts the Contrast.
Brightness
Adjusts the Brightness.
Sharpness
Adjusts the picture Sharpness.
Color
Adjusts the picture Color.
Tint
Adds a natural tone to the display.
Note
Operates only if the video signal is NTSC.
Adjusting the LCD Display
Color Tone
The color tones can be changed. The individual Color components are also user adjustable.
Note
Not available when Dynamic Contrast is set to On.
1.
Off
2.
Cool2
3.
Cool1
4.
Normal
5.
Warm1
6.
Warm2
Note
If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp. function
is disabled.
Color Temp.
Color temp. is a measure of the 'warmth' of the image colors.
Note
This function is enabled when Mode is set to Custom, and Dynamic Contrast and Color Tone are
Off.
Size
The Size can be switched.
PC mode (PC, HDMI [PC Timing]) : 16:9 - 4:3
Adjusting the LCD Display
Video mode (HDMI [Video Timing], AV or Component): 16:9 - Zoom1 - Zoom2 - 4:3 - Screen
Fit - Custom
1.
16:9 - Sets the picture to 16:9 wide mode.
2.
Zoom 1 - Magnifies the size of the picture on the screen.
3.
Zoom 2 - Magnifies the size of the picture more than Zoom 1.
4.
4:3 - Sets the picture to 4:3 normal mode.
5.
Screen Fit - Displays the input scenes as they are without any cutoff when HDMI 720p, 1080i,
1080p signals are input.
6.
Custom - Customizes the screen size.
Note
•
Certain external devices may feed the display an out of spec signal that may cause cutoff even
when using the Screen Fit feature.
•
Zoom 1, Zoom 2 are unavailable in HDMI mode.
•
The Position and Reset functions are available in Zoom 1, Zoom 2 or Screen Fit modes.
Digital NR (Digital Noise Reduction)
Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows you to
enjoy clearer and crisper images.
1.
Off
2.
On
Note
Digital NR function is not available for all resolutions.
HDMI Black Level
When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation in the
screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending
Adjusting the LCD Display
on the external device connected. In this case, adjust the screen quality of your TV by configuring the
HDMI Black Level.
1.
Normal
2.
Low
Note
For Timing which can be used for both the PC and the DTV in HDMI mode, HDMI Black Level will
be activated.
Film Mode
Film Mode calibrates unnatural pictures that may occur in a movie (which is in 24 frames).
Moving subtitles may appear corrupted when this mode is enabled.
(In HDMI mode, this function is available when the input signal is interlaced scan; it is not available
in progressive scan.)
1.
Off
2.
On
PIP Picture
Adjusts the PIP Screen Settings.
Note
Available Modes: PIP On
1.
Contrast
Adjusts the Contrast of the PIP window on the screen.
2.
Brightness
Adjusts the Brightness of the PIP window on the screen.
3.
Sharpness
Adjusting the LCD Display
Adjusts the Sharpness of the PIP window on the screen.
Dynamic Contrast
Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an
optimum contrast.
1.
Off
2.
On
Note
Disabled when PIP is set to On.
Lamp Control
Adjusts the inverter lamp in order to reduce energy consumption.
Note
Not available when Dynamic Contrast is set to On.
Brightness Sensor
Brightness Sensor detects the surrounding light intensity and automatically optimizes the screen
brightness accordingly.
1.
Off
2.
On
Uniformity Enhancer
Adjusting the LCD Display
Make the screen brightness even throughout the whole screen.
1.
Off
2.
On
Picture Reset
Reset the screen settings.
Sound
Available Modes
•
PC / DVI / DisplayPort
•
AV
•
Component
•
HDMI
•
MagicInfo
•
TV
Note
•
A TV tuner box (sold separately) must be connected to use the TV.
•
MagicInfo can only be enabled when a network box is connected.
Mode
The LCD Display has a built-in high fidelity stereo amplifier.
1.
Standard
Selects Standard for the standard factory settings.
2.
Music
Selects Music when watching music videos or concerts.
3.
Movie
Adjusting the LCD Display
Selects Movie when viewing movies.
4.
Speech
Selects Speech when watching a show that is mostly dialog (i.e., news).
5.
Custom
Selects Custom if you want to adjust the settings according to your personal preferences.
Custom
The sound settings can be adjusted to suit your personal preferences.
Note
•
You can hear the sound even when sound value is set to 0.
•
If you adjust sound using Custom function, Mode will turn to Custom mode.
Bass
Emphasizes low frequency audio.
Treble
Emphasizes high frequency audio.
Balance
Allows you to Adjusts the sound balance between the left and right speakers.
Auto Volume
Reduces the difference in volume control between broadcasters.
1.
Off
2.
On
Adjusting the LCD Display
SRS TS XT
SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content
over two speakers. TruSurround XT delivers a compelling, virtual surround sound experience through
any two-speaker playback system, including internal television speakers. It is fully compatible with
all multichannel formats.
1.
Off
2.
On
Sound Select
Enable the sound of either the primary or secondary display in PIP mode.
Note
Available when PIP is set to On.
1.
Main
2.
Sub
Sound Reset
Reset the sound settings.
Setup
Available Modes
•
PC / DVI / DisplayPort
•
AV
•
Component
Adjusting the LCD Display
•
HDMI
•
MagicInfo
•
TV
Note
•
A TV tuner box (sold separately) must be connected to use the TV.
•
MagicInfo can only be enabled when a network box is connected.
Language
You can choose one of 14 languages.
Note
The language chosen affects only the language of the OSD. It has no effect on any software running
on the computer.
Time
Clock Set, Sleep Timer, Timer1 / Timer2 / Timer3, and Holiday Management can be set.
Clock Set
Current Time Setting.
Adjusting the LCD Display
Sleep Timer
Turns the LCD Display off automatically at certain times.
1.
Off
2.
30
3.
60
4.
90
5.
120
6.
150
7.
180
Timer1 / Timer2 / Timer3
You can set the LCD display to automatically turn on or off at a specified time.
Note
•
Hoilday : select Apply to disable the timer on holidays and Don't Apply to enable the timer on
holidays.
•
Only enabled when the clock is set using the Clock Set menu.
•
The Manual option allows you to select a day of the week.
•
Source : Selects the external input source that will be displayed when the selected monitor is turned
on.
•
Repeat : Available selections include Once, EveryDay, Mon~Fri, Mon~Sat, Sat~Sun, and
Manual.
•
Once : The Timer goes off only once.
•
EveryDay : The Timer repeats daily.
•
Mon~Fri : The Timer repeats from Monday through Friday.
Adjusting the LCD Display
•
Mon~Sat : The Timer repeats from Monday through Saturday.
•
Sat~Sun : The Timer goes off on Saturday and Sunday.
•
Manual : Select a day of the week you want the Timer to go off.
Holiday Management
•
Add
You can register holidays.
•
Delete Selected
You can delete selected holidays.
Note
•
•
Only enabled when registered holidays are selected.
•
More than one holiday can be selected and deleted.
Delete All
You can delete all the registered holidays.
Adjusting the LCD Display
Menu Transparency
Change the transparency of the background of the OSD.
1.
High
2.
Medium
3.
Low
4.
Opaque
Safety Lock
Change PIN
The password can be changed.
The preset password for the LCD Display is "0000".
Note
If you forgot your password, press the remote buttons INFO → EXIT → MUTE to reset the password
to "0000."
Lock
This is the function that locks the OSD in order to keep the current settings or to prevent others from
adjusting the settings.
Note
Selecting Lock On will enable Lock Off. To disable the Lock function, enter the password for Lock
Off.
Adjusting the LCD Display
Energy Saving
This feature adjusts the power consumption of the unit in order to save energy.
1.
Off
2.
On
Video Wall
A Video Wall is a set of video screens connected together, so that each screen shows a part of the
whole picture or where the same picture is repeated on each screen.
When the Video Wall is on, you can adjust the Video Wall screen setting.
Note
•
When a Horizontal or Vertical split is over four, use a resolution of XGA (1024 x 768) or greater
to prevent any picture degradation.
•
Size will be disabled when Video Wall is running.
•
Disabled when PIP is set to On.
Video Wall
Turns Off/On the Video Wall function of the selected display Off/On.
Format
•
Off
•
On
Adjusting the LCD Display
The Format can be selected to see a divided screen.
•
Full
Provides a full screen without any margins.
•
Natural
Displays a natural image with the original aspect ratio intact.
Horizontal
Sets how many parts the screen should be divided horizontally.
Fifteen adjustment levels: 1~15.
Note
If Vertical is set to 15, the maximum value for Horizontal is 6.
Vertical
Sets how many parts the screen should be divided vertically.
Fifteen adjustment levels: 1~15.
Note
If Horizontal is set to 15, the maximum value for Vertical is 6.
Screen Position
Adjusting the LCD Display
The screen can be divided into several images. A number of screens can be selected with a different
layout when dividing.
•
Select a mode in Screen Position.
•
Select a display in Display Selection.
•
The selection will be set up by pressing a number in the selected mode.
•
The screen can be split into a maximum of 100 sub-screens.
Note
When more than four displays are connected, we recommend a resolution of XGA (1024*768) or
greater to prevent any picture degradation.
Safety Screen
The Safety Screen function is used to prevent afterimages that may appear when a still picture is
displayed on the screen over a long time.
Note
This function is not available when the power is turned off.
Pixel Shift
Pixel Shift
To prevent after-images on the screen, you can use this function to have pixels move on the LCD in
the horizontal or vertical direction.
•
Off
•
On
Horizontal
Sets how many pixels the screen moves horizontally.
Five adjustment levels: 0, 1, 2, 3, and 4.
Adjusting the LCD Display
Vertical
Sets how many pixels the screen moves vertically.
Five adjustment levels: 0, 1, 2, 3, and 4.
Time
Set the time interval for performing the horizontal or vertical movement, respectively.
Timer
Timer
You can set the timer for Screen Burn Protection.
If you start the operation to erase any residual image, the operation will be performed for the set period
of time and then automatically finish.
•
Off
•
On
Adjusting the LCD Display
Mode
You can change the Safety Screen Type.
•
Bar
•
Eraser
•
Pixel
Period
Use this function to set the execution period for each mode set in the timer.
Time
Within the set period of time specify a time for execution.
•
Bar
Mode - Bar, Eraser, Pixel : 10~50 sec
Adjusting the LCD Display
This function prevents after-images on the screen by moving long black and white vertical lines.
Eraser
This function prevents after-images on the screen by moving a rectangular pattern.
Pixel
This function prevents after-images by moving many pixels on the screen.
Side Gray
Select the brightness of the grey for the screen background.
•
Off
•
Light
•
Dark
Resolution Select
Adjusting the LCD Display
When the picture is not displayed properly on the screen when setting the graphics card resolution of
the computer to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768@ 60Hz or 1366 x 768 @ 60Hz,
by using this function(Resolution Select), you can have the picture displayed on the screen in the
specified resolution.
Note
Available in PC mode only.
1.
Off
2.
1024 X 768
3.
1280 X 768
4.
1360 x 768
5.
1366 X 768
Note
Selecting the menu is only allowed when the graphics resolution is set to 1024 x 768 @ 60Hz, 1280 x
768 @ 60Hz, 1360 x 768 @ 60Hz or 1366 x 768 @ 60Hz.
Power On Adjustment
Adjusts the Power On time for the screen.
Caution: Set the Power On time to be longer to avoid overvoltage.
OSD Rotation
OSD Rotate
1.
Landscape
2.
Portrait
Adjusting the LCD Display
Advanced Settings
Configures the settings more elaborately.
Temperature
Configures the setting for the Temperature function, which detects the internal temperature for the
product's protection.
Temperature Control
Detects the product's internal temperature and specifies the desired temperature.
The product is set to 77°C by default.
Note
•
The picture will be dimmed if the temperature exceeds the specified temperature, and the product
will automatically power off to prevent overheating if the temperature keeps rising.
•
It is best to use the product at temperatures 75 - 80°C (based on ambient temperature of 40°C).
Refer to "Specifications" herein for details about operating conditions.
Current Temperature
Shows the current temperature of the product.
Auto Power
Enables or disables Auto Power for the product.
Adjusting the LCD Display
•
Off
•
On
Note
When Auto Power is On, the product will power on automatically as soon as it is connected to power.
Button Lock
Locks or unlocks the monitor control buttons on the product.
•
Off
•
On
User Auto Color
1.
Auto Color
Automatically adjusts the colors.
2.
Reset
Resets the color settings.
Note
Enabled only in PC mode.
Standby Control
Adjusting the LCD Display
Sets the standby mode, which will be activated when no input signal is detected.
•
Off
A message will read <No Signal> if no input signal is detected.
•
On
Power-saving mode will be activated if no input signal is detected.
•
Auto
When no input signal is detected,
- Power-saving mode will be activated if an external device is connected.
- A message will read <No Signal> if no external device is connected.
Note
•
Enabled only in PC, DVI, HDMI, or DisplayPort mode.
•
This function at <AUTO> doesn't work at HDMI source.
Lamp Schedule
Adjusts the luminance to a user-specified value at a specified time.
OSD Display
Displays or hides a menu item on the screen.
Source OSD
•
Off
•
On
Adjusting the LCD Display
Not Optimum Mode OSD
•
Off
•
On
No Signal OSD
•
Off
•
On
MDC OSD
•
Off
•
On
Software Upgrade
Performs a software upgrade.
1.
Connect the product to a computer via a digital signal such as DVI or HDMI. Click the BMP
image file converted from an SW code. The image below will appear on the screen of the product.
2.
While a BMP image onto which the software code has been converted is displayed on the screen,
select Software Upgrade.
Adjusting the LCD Display
Note
When there are two or more BMP images, they are displayed on the screen using a slideshow.
•
It is recommended that the playback interval between two BMP images in the slideshow
should be one second. The image extraction probability will decrease with other playback
intervals.
•
A BMP image might not be extracted if it is covered by another image (for example, the mouse
pointer).
3.
If a more recent version than the current software version is detected, you will be asked whether
to upgrade the current software. If you select <Yes>, the upgrade is performed.
4.
When the software upgrade is completed, the product is turned off and on automatically.
Note
•
This only operates with a digital signal, such as in DVI, HDMI1, or HDMI2 mode. (The input
resolution must be identical to the panel resolution.)
•
In HDMI1 and HDMI2 modes, the timing values used for both the PC and TV are only supported
if the Edit Name is set to PC or DVI PC.
•
This is only supported if the Size is set to 16:9.
Setup Reset
Reset all the values for a setting.
Reset All
Reset all the settings for the display.
Adjusting the LCD Display
Multi Control
Available Modes
•
PC / DVI / DisplayPort
•
AV
•
Component
•
HDMI
•
MagicInfo
•
TV
ID Setup
Assigns an individual ID to the SET.
ID Input
Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to
the transmitter setting becomes activated.
MDC Connection
Selects a port to receive the MDC inputs from.
Adjusting the LCD Display
Network Setting
IP Setting
•
Auto
•
Manual
- IP Address : Manually enter the IP Address if IP Setting is set to Manual.
- Subnet Mask : Manually enter the Subnet Mask if IP Setting is set to Manual.
- Gateway : Manually enter the Gateway if IP Setting is set to Manual.
MagicInfo
Available Modes
•
PC / DVI / DisplayPort
•
AV
•
Component
•
HDMI
•
MagicInfo
•
TV
Note
•
A TV tuner box (sold separately) must be connected to use the TV.
•
MagicInfo can only be enabled when a network box is connected.
Note
•
The remote control can be used to select MagicInfo. However, it is recommended to use a separate
USB keyboard to utilize MagicInfo fully.
•
For MagicInfo in Device mode, moving external devices while booting may cause errors. Set up
external devices only if the LCD Display turns on.
•
Do not unplug the LAN cable used for the network (ex: video display). Otherwise, the program
(MagicInfo) may stop. If you do unplug the cable, restart the system.
•
Do not unplug the LAN cable used by an USB device (ex: video display). Otherwise, the program
(MagicInfo) may stop.
Adjusting the LCD Display
•
To access other sources, press the SOURCE button in MagicInfo.
•
The preset password for the LCD Display is "000000".
•
The server program's Power-On option works only if the LCD Display's power is completely shut
off.
Please make sure not to use the Power-On option when the LCD Display is in the process of shutting
down since this may cause system errors on the LCD Display.
•
When using MagicInfo with the MagicInfo Server Program: perform Network mode.
•
When using MagicInfo with the device directly connected to LCD Display : execute Device mode.
•
Press ESC to directly go to the MagicInfo Window screen.
•
To setup MagicInfo on a Windows screen, a keyboard and mouse are required.
•
To setup MagicInfo on a Windows screen, refer to the MagicInfo Server Help.
It is highly recommended not to turn off the AC power during an operation.
•
For pivoted LCD Displays, ticker transparency is not supported.
•
For pivoted LCD Displays, a screen resolution of up to 720*480(SD) is supported for movies.
•
For drive D:, EWF is not applied.
•
To save Setup contents that have been changed when EWF is in the Enable state, you must
Commit them.
•
By selecting Disable, Enable or Commit, the system is restarted.
Troubleshooting
Self-Test Feature Check
Note
Check the following items yourself before calling for assistance. Contact a Service Center for problems
that you cannot solve by yourself.
Self-Test Feature Check
1.
Turn off both your computer and the LCD Display.
2.
Unplug the video cable from the back of the computer.
3.
Turn on the LCD Display.
The figure shown below ("No Signal") appears on a black background when the LCD Display is
working normally even though no video signal is detected: While in the Self-Test mode, the LED
power indicator remains green and the figure moves around on the screen.
4.
Turn off your LCD Display and reconnect the video cable; then turn on both your computer and
the LCD Display
If your LCD Display screen remains blank after using the previous procedure, check your video controller and computer system; your LCD Display is functioning properly.
Warning Messages
You can even view the screen at a resolution of 1920 x 1080. However, you will receive the following
message for a minute; You can choose to change the screen resolution or stay in the current mode
during that time. If the resolution is more than 85Hz, you will see the black screen because the LCD
Display does not support over 85Hz.
Note
Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the
LCD Display.
Maintenance and Cleaning
1) Maintaining the LCD Display Case.
Clean with a soft cloth after disconnecting the power cord.
Troubleshooting
•
Do not use benzene, thinner or other flammable substances.
2) Maintaining the Flat Panel Display Screen.
Clean with a soft cloth (cotton flannel).
•
Never use acetone, benzene or thinner.
(They may cause flaws or deformation of the screen surface.)
•
The user is responsible for any damage caused by using
these substances.
Symptoms and Recommended Actions
Note
A LCD Display recreates visual signals received from the computer. Therefore, if there is a problem
with the computer or the video card, this can cause the LCD Display to become blank, have poor
coloring, become noisy, etc. In this case, first check the source of the problem, and then contact a
Service Center or your dealer.
1.
Check if the power cord and the video cables are properly connected to the computer.
2.
Check if the computer beeps more than 3 times when booting.
(If it does, request service.)
3.
If you installed a new video card or if you assembled the PC, check if you installed the Adaptor
(video).
4.
Check if the scanning ratio of the video screen is set to between 50 Hz ~ 85 Hz.
(Do not exceed 60Hz when using the maximum resolution.)
5.
If you have problems in installing the Adaptor (video) driver, boot the computer in Safe Mode,
remove the Display Adaptor in the "Control Panel −> System −> Device Administrator" and then
reboot the computer to reinstall the Adaptor (video) driver.
Check List
Note
•
The following table lists possible problems and their solutions. Before calling for assistance, check
the information in this section to see if you can remedy any problems for yourself. If you do need
assistance, please call the phone number on the Information section or contact your dealer.
Problems related to the Installation (PC Mode)
Note
Problems related to the LCD Display installation and their solutions are listed.
Q:
The LCD Display screen flickers.
A:
Check if the signal cable between the computer and the LCD Display is securely connected.
Troubleshooting
(Refer to Connecting a Computer)
Problems related to the Screen
Note
Problems related to the LCD Display screen and their solutions are listed.
Q:
The screen is blank and the power indicator is off.
A:
Ensure that the power cord is firmly connected and the LCD Display is on.
(Refer to the Connecting a Computer)
Q:
"No Signal" message.
A:
Ensure that the signal cable is firmly connected to the PC or video sources.
(Refer to the Connecting a Computer)
A:
Ensure that the PC or video sources are turned on.
Q:
"Not Optimum Mode" message.
A:
Check the maximum resolution and the frequency of the video Adaptor.
A:
Compare these values with the data in the Preset Timing Modes Chart.
Q:
The picture rolls vertically.
A:
Check if the signal cable is securely connected. Re-connect it, if necessary.
(Refer to Connecting a Computer)
Q:
The image is not clear; picture is blurred.
A:
Run Frequency Coarse and Fine tuning.
A:
Turn on again after removing all accessories (video extension cable, etc.)
A:
Set the resolution and frequency to the recommended ranges.
Q:
The picture image is unstable and shakes.
A:
Check if the resolution and frequency set for the computer video card falls in the range supported
by the LCD Display. If not, reset them referring to the current Information under the LCD Display
menu and Preset Timing Modes.
Q:
Ghost images are shown in the picture.
A:
Check if the resolution and frequency set for the computer video card falls in the range supported
by the LCD Display. If not, reset them referring to the current Information under the LCD Display
menu and Preset Timing Modes.
Q:
The image is too light or too dark.
A:
Adjust the brightness and contrast.
(Refer to the Brightness, Contrast)
Q:
The screen color is inconsistent.
A:
Adjust color using Custom under OSD Color Adjustment menu.
Troubleshooting
Q:
The color image is distorted by dark shadows.
A:
Adjust color using Custom under OSD Color Adjustment menu.
Q:
The color white is poor.
A:
Adjust color using Custom under OSD Color Adjustment menu.
Q:
The Power Indicator blinks.
A:
The LCD Display is currently saving the changes made in the settings to the OSD memory.
Q:
The screen is blank and the power indicator light blinks every 0.5 or 1 seconds.
A:
The LCD Display is using its power management system. Press any key on the keyboard.
Problems related to Audio
Note
Problems related to audio signals and their solutions are listed below.
Q:
No sound.
A:
Ensure that the audio cable is firmly connected to both the audio-in port on your LCD Display
and the audio-out port on your sound card.
(Refer to the Connecting a Computer)
A:
Check the volume level.
Q:
The sound level is too low.
A:
Check the volume level.
A:
If the volume is still too low after turning the control to its maximum, check the volume control
on the computer sound card or software program.
Q:
The sound is too high or too low.
A:
Adjusts the Treble and Bass to the appropriate levels.
Problems related to the Remote Control
Note
Problems related to the remote control and their solutions are listed.
Q:
The remote control buttons do not respond.
A:
Check the polarities (+/-) of the batteries.
A:
Check if the batteries are empty.
A:
Check if the power is on.
A:
Check if the power cord is securely connected.
A:
Check if a special fluorescent or neon lamp is on in the vicinity.
Q:
How can I change the frequency?
Q&A
Troubleshooting
A:
The frequency can be changed by reconfiguring the video card.
Note
That video card support can vary, depending on the version of the driver used. (Refer to the
computer or the video card manual for details.)
Q:
How can I adjust the resolution?
A:
Windows XP:
Control Panel → Appearance and Themes → Display → Settings.
A:
Windows ME/2000:
Control Panel → Display → Settings.
* Contact the video card manufacturer for details.
A:
Windows 7:
Go to Control Panel → Appearance and Personalization→ Display → Adjust Resolution and
adjust the resolution.
Q:
How can I set the Power Saving function?
A:
Windows XP:
Control Panel → Appearance and Themes → Display → Screen Saver.
Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual).
A:
Windows ME/2000:
Control Panel → Display → Screen Saver.
Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual).
A:
Windows 7:
Set power-saving mode in Control Panel → Appearance and Personalization→ Personalize →
Screen Saver Settings or BIOS SETUP on the PC.
Q:
How can I clean the outer case/LCD Panel?
A:
Disconnect the power cord and then clean the LCD Display with a soft cloth, using either a
cleaning solution or plain water.
Do not leave any detergent or scratches on the case. Do not let any water enter the LCD Display.
Q:
How can I play the video?
A:
The video supports the MPEG1 and WMV codecs only. Install the corresponding codec to play
the video. Note that some of the codecs can be incompatible.
Note
Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or
contact your dealer.
Specifications
General
General
Model Name
SyncMaster UD55A
LCD Panel
Size
54.6 inch / 138 cm
Display area
1209.6 mm (H) x 680.4 mm (V)
Pixel Pitch
0.63 mm (H) x 0.63 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 85 Hz
Display Color
16.7M
Resolution
Optimum resolution
1920 x 1080 @ 60 Hz
Maximum resolution
1920 x 1080 @ 60 Hz
Maximum Pixel Clock
148.5 MHz (Analog,Digital)
Power Supply
This product supports 100 - 240 V.
Since the standard voltage may differ from country to country, please check the label on
the back of the product.
Signal connectors
Input : Internal Tuner(ATV/DTV) - An America Product Only Composite/Component
(common), PC D-Sub, DVI, HDMI, DP, Audio In, LAN, RS232C IN,a removable brightness sensor
Output : DVI Out(Loopout), Audio Out, RS232C Out, IR Out
Network : USB3.0, USB2.0, LAN, DP Out (applicable only when the network box is connected using a cable)
Dimensions (W x H x D) / Weight
1261.3 x 686.1 x 96.0 mm / 49.7 x 27.0 x 3.8 inches, 24.0 kg / 52.9 lbs
VESA Mounting Interface
600.0 mm x 400.0 mm
Specifications
Environmental considerations
Operating (With Network Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Box)
Humidity : 10 % ~ 80 %, non-condensing
Operating (Without Network Temperature : 32°F ~ 104°F (0°C ~ 40°C)
Box)
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This LCD Display can be installed on any Plug & Play compatible system. The interaction
of the LCD Display and the computer systems will provide the best operating conditions
and LCD Display settings. In most cases, the LCD Display installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED,
GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may
be seen. This is not from bad quality and you can use it without any problems.
For example, the number of TFT-LCD sub pixels contained in this product are 6,220,800.
Note
•
Design and specifications are subject to change without prior notice.
•
Attaching a Samsung ID (videowall kit) will increase the weight of an LFD by 1.6 kg.
Class B(Information Communication equipment for residential use)
This device is registered for EMC requirements for home use (Class B). It can be used in all areas.
(Class B equipment emits less electromagnetic waves than Class A equipment.)
(USA only)
Dispose unwanted electronics through an approved recycler.
To find the nearest recycling location, go to our website:
www.samsung.com/recyclingdirect Or call, (877) 278 - 0799
PowerSaver
This LCD Display has a built-in power management system called PowerSaver. This system saves
energy by switching your LCD Display to low-power mode when it has not been used for a certain
amount of time. The LCD Display automatically returns to normal operation when you press a key on
the keyboard. For energy conservation, turn your LCD Display OFF when it is not needed, or when
leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant
video card installed in your computer. Use the software utility installed on your computer to set up this
feature.
Specifications
PowerSaver
State
Normal Op- Power saving
eration
mode
Power off
Power off
(Power
Swich)
Power Indicator
On
Blinking
Amber
Off
Power Consumption
225 Watts
1 Watts
1 Watts
0 Watts
Power off
Power off
State
Normal Op- Power saving
eration
mode
(Power
Swich)
(Typical)
Note
•
The actual power consumption may be different from the indicated power consumption above if
the system conditions or settings are changed.
•
To stop any power consumption, turn off the switch or disconnect the power cable on the back. Be
sure to disconnect the power if you intend to stay away from home for many hours.
•
If you connect a network box (sold separately), the LFD will no longer be in compliance with
Energy Star 5.0.
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 350
31.469
70.086
25.175
+/-
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 848 x 480
31.020
60.000
33.750
+/+
Specifications
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 768
47.776
59.870
79.500
-/+
VESA, 1280 x 960
60.000
60.000
108.000
+/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1360 x 768
47.712
60.015
85.500
+/+
VESA, 1366 x 768
47.712
59.790
85.500
+/+
Display Mode
Horizontal
Frequency
(kHz)
Vertical Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA,1920 x 1080
66.587
59.934
138.500
+/-
VESA,1920 x 1080
67.500
60.000
148.500
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the
left edge of the screen horizontally is called the Horizontal
Cycle and the inverse number of the Horizontal Cycle is
called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same
image many times per second to display an image to the
user. The frequency of this repetition is called the Vertical
Frequency or Refresh Rate. Unit: Hz
Information
For a Better Display
Adjust the computer resolution and screen injection rate (refresh rate) on the computer
as described below to enjoy the best picture quality. You can have an uneven picture quality
on screen if the best picture quality is not provided for TFT-LCD.
•
Resolution: 1920 x 1080
•
Vertical frequency (refresh rate): 60 Hz
TFT-LCD panels manufactured by using advanced semiconductor technology with a
precision of 1ppm (one millionth) and above is used for this product. But the pixels of RED,
GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels
could be seen. This is not from bad quality and you can use it without any problems.
•
For example, the number of TFT-LCD sub pixels contained in this product are
6,220,800.
When cleaning the monitor and the panel outside, please apply a small amount of water
to a soft cloth. Rub softly when cleaning the LCD area.If excessive force is applied, you
may stain it.
If you are not satisfied with the picture quality, you can get better quality of picture by
performing the "Auto Adjustment function" in display screen that is appeared as window
termination button is pressed. If there's still noise after the automatic adjustment, use the
Fine/Coarse adjustment function.
When viewing a fixed screen for an extended period of time, a residual image or blurriness may appear. Change the mode to energy save or set a screensaver to move the picture
when you need to be away from the monitor for an extended period of time.
PRODUCT INFORMATION (Image Retention Free)
What is Image Retention ?
Image retention may not occur when a LCD panel is operated under normal conditions.
Normal conditions are defined as continuously changing video patterns. When the LCD
panel is operated for a long time with a fixed pattern (over 12 hours), there may be slight
difference in voltage between electrodes that work the liquid crystal (LC) in a pixel. The
voltage difference between electrodes increases with time, forcing the liquid crystal to lean.
When this occurs, the previous image may be seen when the pattern is changed. To prevent
this, the accumulated voltage difference must be decreased.
Information
Power Off, Screen Saver, or Power Save Mode
•
Turn the power off for 2 hours after 12 hours in use
•
Set the Monitor to power off with the PC Display Properties Power Scheme.
•
Use a Screen saver if possible - Screen saver in one color or a moving image is recommended.
•
The Image Retention Free function applied to the product is recommended.
- For detailed configuration procedures, refer to the back page.
Change the Color Information periodically
Note
Use Two different colors
Rotate the Color Information with 2 different colors every 30 minutes.
•
Avoid using a combination of characters and background color with large difference in
luminance.
Avoid using Grey colors, which can cause Image retention easily.
Avoid: Colors with big difference in luminance (Black & White, Grey)
Information
Change the characters color periodically
•
Use Bright colors with little difference in luminance.
- Cycle : Change the characters color and background color every 30 minutes
•
Every 30 minutes, change the characters with movement.
•
Have the images and logo cycle periodically.
- Cycle: Display moving image together with Logo for 60 seconds after 4 hours in use.
•
The best way to protect your monitor from Image retention is to turn the Power off, or
set your PC or System to operate a Screen Saver program when you are not using it. If
these guidelines are not followed, it may affect your warranty.
Apply the Screen Pixel function on Product
•
Apply the Screen Pixel function
- Symptom: Dot with Black Color move up and down.
•
Apply the Screen Bar function
- Symptom: Horizontal / Vertical Bar with Black Color move up and down.
Apply the Screen Erasing function on Product
Information
•
Apply the Screen Erasing function
- Symptom: 2 Vertical blocks move while erasing the display
Appendix
Contact SAMSUNG WORLDWIDE
Note
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care center.
North America
CANADA
1-800-SAMSUNG (726-7864)
http://www.samsung.com
MEXICO
01-800-SAMSUNG (726-7864) http://www.samsung.com
U.S.A
1-800-SAMSUNG (726-7864)
http://www.samsung.com
Latin America
ARGENTINA
0800-333-3733
http://www.samsung.com
BRAZIL
0800-124-421
http://www.samsung.com
4004-0000
CHILE
800-SAMSUNG (726-7864)
http://www.samsung.com
COLOMBIA
01-8000112112
http://www.samsung.com
COSTA RICA
0-800-507-7267
http://www.samsung.com
DOMINICA
1-800-751-2676
http://www.samsung.com
ECUADOR
1-800-10-7267
http://www.samsung.com
EL SALVADOR
800-6225
http://www.samsung.com
GUATEMALA
1-800-299-0013
http://www.samsung.com
HONDURAS
800-27919267
http://www.samsung.com
JAMAICA
1-800-234-7267
http://www.samsung.com
NICARAGUA
00-1800-5077267
http://www.samsung.com
PANAMA
800-7267
http://www.samsung.com
PERU
0-800-777-08
http://www.samsung.com
PUERTO RICO
1-800-682-3180
http://www.samsung.com
TRINIDAD & TO- 1-800-SAMSUNG (726-7864)
BAGO
http://www.samsung.com
VENEZUELA
http://www.samsung.com
0-800-100-5303
Europe
ALBANIA
42 27 5755
-
AUSTRIA
0810 - SAMSUNG (7267864, € http://www.samsung.com
0.07/min)
BELGIUM
02-201-24-18
http://www.samsung.com/be
(Dutch)
http://www.samsung.com/be_fr
(French)
BOSNIA
05 133 1999
-
BULGARIA
07001 33 11
http://www.samsung.com
CROATIA
062 SAMSUNG (062 726 7864) http://www.samsung.com
Appendix
Europe
CZECH
800 - SAMSUNG (800-726786) http://www.samsung.com
DENMARK
70 70 19 70
http://www.samsung.com
FINLAND
030 - 6227 515
http://www.samsung.com
FRANCE
01 48 63 00 00
http://www.samsung.com
GERMANY
01805 - SAMSUNG (726-7864, http://www.samsung.com
€ 0,14/Min)
GREECE
2106293100
http://www.samsung.com
HUNGARY
06-80-SAMSUNG (726-7864)
http://www.samsung.com
ITALIA
800-SAMSUNG (726-7864)
http://www.samsung.com
KOSOVO
+381 0113216899
-
LUXEMBURG
261 03 710
http://www.samsung.com
MACEDONIA
023 207 777
-
MONTENEGRO
020 405 888
-
NETHERLANDS
0900-SAMSUNG
(0900-7267864) ( € 0,10/Min)
http://www.samsung.com
NORWAY
815-56 480
http://www.samsung.com
POLAND
0 801 1SAMSUNG (172678)
http://www.samsung.com
022-607-93-33
PORTUGAL
80820 - SAMSUNG (7267864) http://www.samsung.com
RUMANIA
http://www.samsung.com
SERBIA
0700 SAMSUNG (0700 726 http://www.samsung.com
7864)
SLOVAKIA
0800 - SAMSUNG (0800-726 http://www.samsung.com/sk
786)
SPAIN
902 - 1 - SAMSUNG (902 172 http://www.samsung.com
678)
SWEDEN
0771 726 7864 (SAMSUNG)
SWITZERLAND
0848 - SAMSUNG (7267864, http://www.samsung.com/ch
CHF 0.08/min)
http://www.samsung.com/
ch_fr/(French)
U.K
0330 SAMSUNG (7267864)
http://www.samsung.com
EIRE
0818 717100
http://www.samsung.com
LITHUANIA
8-800-77777
http://www.samsung.com
LATVIA
8000-7267
http://www.samsung.com
ESTONIA
800-7267
http://www.samsung.com
TURKEY
444 77 11
http://www.samsung.com
http://www.samsung.com
CIS
RUSSIA
8-800-555-55-55
http://www.samsung.com
GEORGIA
8-800-555-555
-
Appendix
CIS
ARMENIA
0-800-05-555
-
AZERBAIJAN
088-55-55-555
-
KAZAKHSTAN
8-10-800-500-55-500
7799)
(GSM: http://www.samsung.com
UZBEKISTAN
8-10-800-500-55-500
http://www.samsung.com
KYRGYZSTAN
00-800-500-55-500
http://www.samsung.com
TADJIKISTAN
8-10-800-500-55-500
http://www.samsung.com
UKRAINE
0-800-502-000
http://www.samsung.com/ua
http://www.samsung.com/ua_ru
BELARUS
810-800-500-55-500
-
MOLDOVA
00-800-500-55-500
-
Asia Pacific
AUSTRALIA
1300 362 603
http://www.samsung.com
NEW ZEALAND
0800 SAMSUNG (0800 726 http://www.samsung.com
786)
CHINA
400-810-5858
http://www.samsung.com
HONG KONG
(852) 3698 - 4698
http://www.samsung.com/hk
http://www.samsung.com/
hk_en/
INDIA
3030 8282
http://www.samsung.com
1800 3000 8282
INDONESIA
0800-112-8888
http://www.samsung.com
021-5699-7777
JAPAN
0120-327-527
http://www.samsung.com
MALAYSIA
1800-88-9999
http://www.samsung.com
PHILIPPINES
1-800-10-SAMSUNG
(726-7864)
http://www.samsung.com
1-800-3-SAMSUNG (726-7864)
1-800-8-SAMSUNG (726-7864)
02-5805777
SINGAPORE
1800-SAMSUNG (726-7864)
http://www.samsung.com
THAILAND
1800-29-3232
http://www.samsung.com
02-689-3232
TAIWAN
0800-329-999
http://www.samsung.com
VIETNAM
1 800 588 889
http://www.samsung.com
Middle East
IRAN
021-8255
http://www.samsung.com
http://www.samservice.com
Appendix
Middle East
OMAN
800-SAMSUNG (726-7864)
http://www.samsung.com
KUWAIT
183-2255
http://www.samsung.com
BAHRAIN
8000-4726
http://www.samsung.com
EGYPT
08000-726786
http://www.samsung.com
JORDAN
800-22273
http://www.samsung.com
MOROCCO
080 100 2255
http://www.samsung.com
SAUDI ARABIA
9200-21230
http://www.samsung.com
U.A.E
800-SAMSUNG (726-7864)
http://www.samsung.com
Africa
NIGERIA
0800-SAMSUNG (726-7864)
http://www.samsung.com
SOUTH AFRICA
0860-SAMSUNG (726-7864)
http://www.samsung.com
Terms
Dot Pitch
The image on a monitor is composed of red, green and blue dots.
The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit:
mm
Vertical Frequency
The screen must be redrawn several times per second in order to
create and display an image for the user. The frequency of this
repetition per second is called the Vertical Frequency or Refresh
Rate. Unit: Hz
Example: If the same light repeats itself 60 times per second, this
is regarded as 60 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge
of the screen horizontally is called the Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Interlace
Methods
Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non-Interlace method while showing odd lines and then even lines in turn is called the Interlace
method. The Non-Interlace method is used for the majority of
monitors to ensure a clear image. The Interlace method is the same
as that used in TVs.
and
Non-Interlace
Plug & Play
This is a function that provides the best quality screen for the user
by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard
VESA DDC for the Plug & Play function.
Resolution
The number of horizontal and vertical dots used to compose the
screen image is called the 'resolution'. This number shows the accuracy of the display. A high resolution is good for performing
multiple tasks as more image information can be shown on the
screen.
Example: If the resolution is 1920 x 1080, this means the screen
is composed of 1920 horizontal dots (horizontal resolution) and
1080 vertical lines (vertical resolution).
Appendix
Correcte verwijdering
Correcte verwijdering van dit product (elektrische & elektronische afvalapparatuur)
Dit merkteken op het product, de accessoires of het informatiemateriaal
duidt erop dat het product en zijn elektronische accessoires (bv. lader,
headset, USB-kabel) niet met ander huishoudelijk afval verwijderd mogen worden aan het einde van hun gebruiksduur. Om mogelijke schade
aan het milieu of de menselijke gezondheid door ongecontroleerde afvalverwijdering te voorkomen, moet u deze artikelen van andere soorten
afval scheiden en op een verantwoorde manier recyclen, zodat het duurzame hergebruik van materiaalbronnen wordt bevorderd.
Huishoudelijke gebruikers moeten contact opnemen met de winkel waar
ze dit product hebben gekocht of met de gemeente waar ze wonen om
te vernemen waar en hoe ze deze artikelen milieuvriendelijk kunnen laten
recyclen.
Zakelijke gebruikers moeten contact opnemen met hun leverancier en de
algemene voorwaarden van de koopovereenkomst nalezen. Dit product
en zijn elektronische accessoires mogen niet met ander bedrijfsafval voor
verwijdering worden gemengd.
Correcte behandeling van een gebruikte accu uit dit product
(Van toepassing op de Europese Unie en andere Europese landen met
afzonderlijke inzamelingssystemen voor accu’s en batterijen.)
Dit merkteken op de accu, handleiding of verpakking geeft aan dat de
accu in dit product aan het einde van de levensduur niet samen met ander
huishoudelijk afval mag worden weggegooid. De chemische symbolen
Hg, Cd of Pb geven aan dat het kwik-, cadmium- of loodgehalte in de
accu hoger is dan de referentieniveaus in de Richtlijn 2006/66/EC. Indien
de gebruikte accu niet op de juiste wijze wordt behandeld, kunnen deze
stoffen schadelijk zijn voor de gezondheid van mensen of het milieu.
Ter bescherming van de natuurlijke hulpbronnen en ter bevordering van
het hergebruik van materialen, verzoeken wij u afgedankte accu’s en
batterijen te scheiden van andere soorten afval en voor recycling aan te
bieden bij het gratis inzamelingssysteem voor accu’s en batterijen in uw
omgeving.
Opmerking
De oplaadbare accu in dit product kan niet door de gebruiker zelf worden vervangen. Neem
contact op met uw serviceprovider voor informatie over vervanging.
Appendix
Authority
Information in this document is subject to change without notice.
© 2011 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co.,
Ltd. is strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPM and DDC are registered
trademarks of Video Electronics Standard Association; All other product names mentioned herein may
be the trademarks or registered trademarks of their respective owners.
TruSurround XT, SRS and the
symbol are trademarks of SRS Labs, Inc.
TruSurround XT technology is incorporated under license from SRS Labs,
Inc.