RedMax EDG2300 Specifications

6325-93110 (003)
OWNER / OPERATOR MANUAL
PORTABLE GAS DRILL
EDG2300
(NOTE: Drill is optional part.)
WARNING
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
APPLICABLE SERIAL NUMBERS :
Thank you for purchasing a RedMax
product.
Before using our portable gas drill,
please read this manual carefully to
understand the proper use of your unit.
901112 and up
Read this manual carefully to understand
all safety precautions, controls, proper
operation and maintenance of your
RedMax portable gas drill. Failure to do so
could result in serious injury.
SAFETY FIRST
Instructions contained in warnings within this manual marked with a
symbol
concern critical points which must be taken into consideration to prevent
possible serious bodily injury, and for this reason you are requested to read all
such instructions carefully and follow them without fail.
Note that there may be times when warning seals peel off or become soiled and
impossible to read. If this happens, you should contact the dealer from which
you purchased the product to order new seals and affix the new seal(s) in the
required location(s).
■ Notes on types of warnings
WARNING
IMPORTANT
NOTE
Instructions labeled as shown at left, concern critical steps or
procedures which must be followed in order to prevent accidents
which could lead to serious bodily injury or death. This mark is
used to indicate instructions which must be followed without
exception.
Instructions labeled as shown at left concern steps or procedures
which, if not followed correctly, could lead to mechanical failure,
breakdown, or damage.
Used to label supplementary instructions designed to provide
hints or directions useful in the use of the product.
CONTENTS
SAFETY PRECAUTIONS .................................................................................. 4
IN ORDER TO ENSURE PROPER AND SAFE OPERATION OF YOUR PORTABLE GAS DRILL
WORK GEAR AND CLOTHING
WARNINGS CONSIDERING HANDLING OF FUEL
THINGS TO CHECK BEFORE USING YOUR PORTABLE GAS DRILL
THINGS TO CHECK BEFORE STARTING UP THE ENGINE
AVOID NOISE PROBLEM
THINGS TO BE CAREFUL ABOUT WHEN USING YOUR PORTABLE GAS DRILL
NOTES ON CARE AND MAINTENANCE OF YOUR PORTABLE GAS DRILL
PARTS LOCATION & SPECIFICATIONS .......................................................... 9
SETUP ................................................................................................................ 9
FUEL ................................................................................................................ 10
HOW TO MIX FUEL
FUELING THE UNIT
OPERATION ..................................................................................................... 11
THROTTLE CABLE ADJUSTMENT
STARTING ENGINE
STOPPING ENGINE
BORING OPERATION
ADJUSTMENT OF IDLING SPEED
MAINTENANCE ............................................................................................... 13
DAILY INSPECTION
INSPECTION EVERY 25 HOURS
INSPECTION EVERY 100 HOURS
STORAGE ........................................................................................................ 14
BEFORE LONG-TERM STORAGE
PARTS LIST ..................................................................................................... 15
Safety Precautions
■ In order to ensure proper and safe
operation of your portable gas drill
• Avoid running the engine indoors. The
exhaust gases contain harmful carbon
monoxide.
• Read this Owner/Operator Manual
carefully. Be sure you understand how
to operate this unit properly before you
use it. Failure to do so could result in
serious injury.
• Be sure to keep this manual handy so
that you may refer to it later whenever
any questions arise. Also note that you
are requested to contact the dealer from
whom you purchased the product for
assistance in the event that you have
any questions which cannot be
answered herein.
• Always be sure to include this manual
when selling, lending, or otherwise
transferring the ownership of this
product.
• This product has been designed for use in
drilling, and it should never be used for
any other purpose since doing so could
result in unforeseen accidents and injuries
occurring.
• You should never use this portable gas
drill when under the influence of alcohol,
when suffering from exhaustion or lack of
sleep, when suffering from drowsiness as
a result of having taken cold medicine, or
at any other time when a possibility exists
that your judgment might be impaired or
that you might not be able to operate the
portable gas drill properly and in a safe
manner. Also be sure never to allow
children or anyone unable to fully
understand the directions given in this
manual to use this portable gas drill.
❲4 ❳
• Never use your portable gas drill under
circumstances like those described below:
1. When the ground is slippery or when
other conditions exist which might
make it not possible to maintain a
steady posture while using the portable
gas drill.
2. At night, at times of heavy fog, or at any
other times when your field of vision
might be limited and it would be difficult
to gain a clear view of the area where
the portable gas drill is to be used to
ensure safety.
3. During rain storms, during lightning
storms, at times of strong or gale-force
winds, or at any other times when
weather conditions might make it
unsafe to use this product.
• When using this product for the first time,
before beginning actual work, take the
portable gas drill to a wide, clear, open
space, turn on the power, and practice
handling the portable gas drill until you are
sure that you will be able to handle in it
properly in actual operation.
• Lack of sleep, tiredness, or physical
exhaustion results in lower attention
spans, and this in turn leads to accidents
and injury. When planning your work
schedule, allow plenty of time to perform
the work of cutting and allow plenty of
time for rest. Limit the amount of time
over which the portable gas drill is to be
used continuously to somewhere around
30~40 minutes per session, and take
10~20 minutes of rest between work
sessions. Also try to keep the total amount
of work performed in a single day under 2
hours or less.
Safety Precautions
■ Work gear and clothing
■ Warnings considering handling of fuel
• When using your portable gas drill, always
be sure to wear strong, durable, work
clothing; shirts should be long-sleeved
shirts and pants should be full-length
pants reaching down to the ankles.
• The engine of the portable gas drill is
designed to run on a mixed fuel which
contains highly flammable gasoline. This
fuel is highly flammable and you should
never store cans of fuel or refill the tank of
the portable gas drill in any place where
there is a boiler, stove, wood fire,
electrical sparks, welding sparks, or any
other source of heat or fire which might
ignite the fuel.
• Always be sure to wear and helmet and
face protector when using your portable
gas drill.
• When using your portable gas drill, always
be sure to wear thick work gloves to
protect your hands and non-slip-sole work
boots to prevent you from slipping. Never
use your portable gas drill when wearing
pants with loose cuffs, when wearing
sandals, or when barefoot.
• When using your portable gas drill for an
extended period of time, you should wear
ear protectors to protect yourself from loss
of hearing from overexposure to high
levels of sound.
• Smoking while operating the portable gas
drill or refilling its fuel tank is extremely
dangerous. Always be sure to keep lit
cigarettes away from the portable gas drill
at all times.
• When refilling the tank always turn off the
engine first and take a careful look around
to make sure that there are no sparks or
open flames anywhere nearby before
refueling.
• If any fuel spillage occurs during refueling,
always be sure to use a dry rag to wipe
any fuel which has been spilled onto the
portable gas drill before turning the engine
back on again.
• After refueling, screw the fuel cap back
tightly onto the fuel tank and then carry
the portable gas drill to a spot 10feet (3m)
or more away from where it was refueled
before turning on the engine.
❲5 ❳
Safety Precautions
■ Things to check before using your
portable gas drill
■ Things to check before starting up the
engine
• Before beginning work, look around
carefully to get a feel for the shape of the
land, and whether or not there are any
obstacles which might get in the way while
working, and remove any obstacles which
can be cleared away before beginning
work.
• Take a careful look around to make sure
that no obstacles exist within a perimeter
of 15feet (5m)or less around the portable
gas drill before starting the engine.
• The area within a perimeter of 50feet
(15m) of the person using the portable
gas drill should be considered a
hazardous area into which no one should
enter while the portable gas drill is in use,
and when necessary yellow warning rope,
warning signs, or some other form of
warnings should be placed around the
perimeter of the area. When work is to be
performed simultaneously by two or more
persons, care should also be taken to
constantly look around or otherwise check
for the presence and locations of other
people using portable gas drill within the
work area so as to maintain a distance
between each person sufficient to ensure
safety.
• Before beginning work, each component
of the portable gas drill should be checked
to make sure that it is in proper working
order and to make sure that there are no
loose screws or bolts, fuel leaks, ruptures,
dents, or any other problems which might
interfere with safe operation. Be especially
careful at this time to check that there is
nothing wrong with the drills or with the
joints by which the drills are attached to
the portable gas drill.
• The portable gas drill is equipped with a
centrifugal clutch mechanism which
causes the drills to begin to rotate as soon
as the engine is started by putting the
throttle into the start position. When
starting the engine, hold it firmly in place
so as to ensure that nor the throttle may
not come into contact with any obstacles
when the engine starts up.
• Never place the throttle into the high
speed position when starting the engine.
• After starting up the engine, check to
make sure that the drills stop rotating
when the throttle is moved fully back to its
original position. If the drills continue to
rotate even after the throttle has been
moved fully back, turn off the engine and
take the unit to your authorized Red Max
servicing dealer for repair.
■ AVOID NOISE PROBLEM
NOTE
Check and follow the local regulations
as to sound level and hours of
operations for portable gas drill.
• In general, operate portable gas drill
between 8a.m.and 5p.m.on week days
and 9a.m.to 5p.m.weekends. Avoid using
portable gas drill late at night and/or early
in the morning.
❲6 ❳
Safety Precautions
■ Things to be careful about when using
your portable gas drill
• When using your portable gas drill, grip
the handles of the portable gas drill firmly
with both hands, place your feet slightly
apart (slightly further apart than the width
of your shoulders) so that your weight is
distributed evenly across both legs, and
always be sure to maintain a steady, even
posture while working.
• Maintain the speed of the engine at the
level required to perform drilling work, and
never raise the speed of the engine above
the level necessary.
• Always be sure never to allow other
persons to come within the work area
while drilling.
• Be especially careful not to slip if it is
raining or if rain has just stopped, as the
ground is likely to be slippery at such
times.
• If the grass or other object gets caught in
the drill during operation, always be sure
to turn off the engine before removing the
object.
• Guard against hazardous situations at all
times. Warn adults to keep pets and
children away from the area. Establish a
safe method for gaining your attention
during operation. Be careful if you are
approached.
• If someone calls out or otherwise
interrupts you while working, always be
sure to turn off the engine before turning
around.
• Keep operation area clear of all persons,
particularly small children and pets.
• Never touch the spark plug or plug cord
while the engine is in operation. Doing so
may result in being subjected to an
electrical shock.
• Never touch the muffler, spark plug, or
other metallic parts of the engine while the
engine is in operation or immediately after
shutting down the engine. These metallic
parts reach high temperatures during
operation and doing so could result in
serious burns.
• When you finish drilling in one location
and wish to continue work in another spot,
turn off the engine before carrying it to the
new location.
• Never transport the portable gas drill over
rough roads over long distances without
first removing all fuel from the fuel tank, as
doing so might cause fuel to leak from the
tank as a result of shocks absorbed during
transport.
❲7 ❳
Safety Precautions
■ Notes on care and maintenance of your
portable gas drill
• In order to maintain your portable gas drill
in proper working order, perform the
maintenance and checking operations
described in this manual at regular
intervals. In the event that any parts must
be replaced or any maintenance or repair
work not described in this manual must be
performed,
please
contact
a
representative from the store nearest
RedMax authorized servicing dealer for
assistance.
• Under no circumstances should you ever
take apart the portable gas drill or alter it
in any way. Doing so might result in the
portable gas drill becoming damaged
during operation or the portable gas drill
becoming unable to operate properly.
• Always be sure to turn off the engine
before performing any maintenance or
checking procedures.
• When removing, or reattaching the drills,
be sure to wear thick, sturdy gloves and
use only proper tools and equipment to
prevent injury.
• When replacing drills or any other parts or
when replacing the oil or any lubricants,
always be sure to use only RedMax
products or products which have been
certified by RedMax for use with the
portable gas drill.
• Do not use any accessory or attachment
other than those bearing the RedMax
mark and recommended for the unit.
❲8 ❳
Parts Location & Specifications
Spark plug
Muffer
Stop switch
Reduction unit
Chuck
Drill
Throttle lever
Front grip
Rear grip
Starter grip
Air cleaner
Fuel cap
MODEL EDG2300
Overall Dimensions (LxWxH)
Dry Weight
Transmission
Reduction Ratio
Recommended drill size
Engine Type
Displacement
Max. Output
Fuel
Fuel Tank Capacity
Carburetor
Ignition System
Spark Plug
Starting
Stopping
Standard Accessory
(in)
(lbs)
14.3x12.1x9.1 (357x302x227)
10.6 (5.3kg)
Automatic centrifugal clutch and reduction gears
10 : 1
Dia. 1/2in.(12.5mm)
Air cooled 2-cycle gasoline engine
cc (cu. in)
22.5 (1.37)
kW (HP)
0.87 (1.18) at 8000 rpm
Mixture (Gasoline 32 : 2-cycle oil 1)
pints
1.21
Diaphragm type, Rotary Valve
Transistor controlled flywheel magneto
CHAMPION RCJ-6Y
Recoil starter
Primary circuit short-circuiting
Service tool kit
Specifications are subject to change without notice.
Setup
1. Attach the grip and the drill chuck to the
power unit securely by hand.
2. Insert the drill into the chuck, and tighten
firmly.
❲9 ❳
Fuel
WARNING
• Gasoline is very flammable. Avoid
smoking or bringing any flame or
sparks near fuel. Make sure to stop the
engine and allow it cool before
refueling the unit. Select outdoor bare
ground for fueling and move at least
3m(10ft) away from the fueling stop
before starting the engine.
• The RedMax engines are lubricated by oil
specially formulated for air-cooled 2-cycle
gasoline engine use. If RedMax oil is not
available. Use an anti-oxidant added
quality oil expressly labeled for air-cooled
2-cycle engine use.
RECOMMENDED MIXING RATIO
GASOLINE 32:OIL 1
• Poor quality gasolines or oils may damage
sealing rings, fuel lines or fuel tank of the
engine.
■ HOW TO MIX FUEL
1. Measure out the quantities of gasoline
and oil to be mixed.
2. Put some of the gasoline into a clean,
approved fuel container.
3. Pour in all of the oil and agitate well.
4. Pour in the rest of gasoline and agitate
again for at least one minute.
5. Put a clear indication on the outside of the
container to avoid mixing up with gasoline
or other containers.
6. Indicate the contents on outside of
container for easy identification.
■ FUELING THE UNIT
1. Untwist and remove the fuel cap. Rest the
cap on a dustless place.
2. Put fuel into the fuel tank to 80% of the full
capacity.
3. Fasten the fuel cap securely and wipe up
any fuel spillage around the unit.
WARNING
• Exhaust emission are controlled by the
fundamental engine parameters and
components(eq., carburation, ignition
timing and port timing) without
addition of any major hardware or the
introduction of an inert material during
combustion.
32:1 MIXING CHART
GASOLINE
gal. 1 2 3 4 5
2-CYCLE OIL fl.oz 4 8 12 16 20
GASOLINE
liter
2-CYCLE OIL ml
1 2 3 4 5
32 64 96 128 160
• These engines are certified to operate on
unleaded gasoline.
• Make sure to use gasoline with a
minimum octane number of 90 ROZ
(USA/Canada : pump octane min.87)
• Unleaded gasoline is recommended to
reduce the contamination of the air for the
sake of your health and the environment.
❲ 10 ❳
1. Select bare ground for fueling.
2. Move at least 10 feet (3 meters) away
from the fueling point before starting the
engine.
3. Stop the engine before refueling the unit.
FOR YOUR ENGINE LIFE, AVOID;
1. FUEL WITH NO OIL(RAW GASOLINE) –
It will cause severe damage to the internal
engine parts very quickly.
2. GASOHOL – It can cause deterioration of
rubber and/or plastic parts and disruption
of engine lubrication.
3. OIL FOR 4-CYCLE ENGINE USE or
WATER COOLED 2-CYCLE ENGINE
USE – It can cause spark plug fouling,
exhaust port blocking, or piston ring
sticking.
4.Mixed fuels which have been left
unused for a period of one month or
more may clog the carburetor or result in
the engine failing to operate properly.
Operation
■ Throttle Cable Adjustment
Check the throttle cable play and adjust to
.04 or .08 in. (1~2mm) at the carburetor
side.
Throttle cable
.04 or .08 in.
(1~2mm)
Adjusting screw
NOTE
• The throttle lock makes starting easier.
Always use it when starting the engine.
5. While firmly holding the auger as
illustrated, vigorously pull the starter rope.
Lock nut
■ Starting Engine
1. When first starting up after putting fuel into
the machine, or when re-starting after
running out of fuel, push the priming pump
until fuel runs out the overflow pipe.
Choke lever
CLOSE
OPEN
Priming pump
Overflow pipe
2. Close the choke (push the choke lever
front ward).
3. While pulling the throttle lever, push in the
throttle lock and set the throttle lever to
the starting position.
Throttle lock
6. When engine has ignited first, open the
choke (move the choke lever backward),
pull the starter rope again and the engine
will start.
WARNING
• Keep the drill clear of everything
around it as they will start moving with
the engine start.
7. Pull the throttle lever slightly, and it will be
unlocked automatically.
8. Allow the engine to warm up for a couple
of minutes before starting operation.
NOTE
• When re-starting immediately after
stopping engine, keep the choke open.
• If the engine won't start even after
repeated attempts, it may be overfed with
fuel. Remove and dry the spark plug, and
try to start again with the choke open.
Low speed position
Starting position
High speed position
❲ 11 ❳
Operation
■ Stopping Engine
• Release the throttle lever and press on
the red button until the engine comes to a
complete stop.
Stop button
■ Adjustment of Idling Speed
• The engine idling speed is preadjusted at
the factory so that the engine keeps
running without moving the drill when
releasing the throttle lever to the idling
position. However, due to changes in
engine conditions, it may be necessary to
adjust the idling.
• To increase idling, screw idle adjustment
screw in, until preferred speed is obtained.
To decrease idling, unscrew idle
adjustment screw until preferred speed is
obtained.
■ Boring operation
• Keep the engine running at full throttle
during operation.
• Keep the drill going straight. Tilted boring
can cause the drill to bend.
• Avoid touching the spark plug lead during
operation.
❲ 12 ❳
Idle adjustment
screw
Maintenance
WARNING
• Before cleaning, inspecting or repairing
your unit, make sure that engine has
stopped and is cool. Disconnect the
spark plug terminal to avoid accidental
engine starts.
■ Daily Inspection
• Remove grass or dust, from the entire
body.
• Check that all nuts and screws are
securely tightened, and no parts are
missing.
• Check for leakage of fuel.
• Check and clean the spark plug. Adjust
the electrode gap to .024~.028in
(0.6~0.7mm) if necessary.
.024 ~ .028 in (0.6~0.7mm)
Replacement plug: CHAMPION RCJ-6Y
■ Inspection every 100 hours
• The muffler is equipped with a spark
arrester to prevent red hot carbon from
flying out of the exhaust outlet. In the
State of California it is required by law
(Section 4442 of the California Public
Resources Code) to equip a spark
arrester when a gas powered tool is used
in any forest covered, brush covered, or
grass covered unimproved land.
■ Inspection every 25 hours
• Remove the air cleaner element from the
carburetor air intake cover and wash in
warm, soapy water. Dry completely before
installing.
Cleaner element
Cleaner cover
Speak
Arrester
• Check and tighten each fastener.
• Dismount the engine and check the clutch
system to see if oil is observed between
the clutch lining and its drum. If any, wipe
it off with gasoline.
❲ 13 ❳
Storage
■ Before Long-term Storage
• Drain fuel tank and run engine out until all
fuel in the carburetor is used up.
• Remove the spark plug and drop a
spoonful 2 cycle oil into the cylinder.
Crank the engine several times and
replace the plug.
Pull starter until compression is felt.
• Brush off dirt from the drill surface and
apply rust protective oil.
• Store the machine in a dry, dust-free
place.
❲ 14 ❳
Parts List
PORTABLE GAS DRILL
EDG2300
NOTE :
1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or
replacement.
2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the
use of any parts other than those specified by the company.
3. When placing parts orders for repair and/or replacement, check if the model name and the
serial number are applicable to those specified in the parts list, then use parts number
described in the parts list.
4. The contents described in the parts list may change due to improvement.
5. The parts for the machine shall be supplied seven (7) years after the machine is
discontinued. [It is possible that some specific parts may be subject to change of their
delivery term and list price within the limit of ten (7) years after the machine is
discontinued. It is also possible that some parts may be available even after the limit of
seven (7) years.]
APPLICABLE SERIAL NUMBERS :
901112 and up
❲ 15 ❳
Parts List : EDG2300
Fig.1 DRIVE UNIT and TOOLS (S/N 901112 and up)
❲ 16 ❳
EDG2300
Fig.1 DRIVE UNIT and TOOLS (S/N 901112 and up)
Key#
Part Number
Description
Q'ty
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
3871-21100
3871-21120
3871-21320
3545-14240
01641-21423
3524-14400
0280-10504
01601-20513
0263-30516
0280-10504
3872-21510
3871-21200
3541-14221
3872-21520
0225-30616
0225-10616
3890-11102
3890-11140
3890-11201
06030-06001
06031-06001
06030-06202
06034-06202
3127-13230
04065-03515
3890-12110
04064-01210
3872-13101
3872-13130
3872-13140
3890-13140
04010-00310
0224-00610
01641-20608
3310-12281
3872-13150
3872-91000
3541-91110
1030-91340
1110-91320
3540-91120
3871-91350
Right handle comp.
• Grip
Stay
Bolt
Washer
Lever, Throttle
Nut
Washer
Screw
Nut
Bracket, Right
Left handle comp.
• Grip
Bracket, Left
Bolt
Bolt
Case Comp., Rear half
• Dowel pin
Case comp., Front half
Bearing
Bearing (Single shield)
Bearing
Bearing (Double shield)
Speacer
Ring
Clutch drum
Ring
Gear comp., Drive
• Gear, Idler
Gear, Driven
Shaft, PTO
Key
Bolt
Washer
Screw
Nut
Tool set
• Bag
• Screwdriver
• Scoket (Hex. 19mm)
• Spanner (8mm x 10mm)
• Spanner (17mm x 13mm)
1
1
1
1
1
1
1
1
2
2
1
1
1
1
4
4
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
4
1
1
1
1
1
1
1
Key#
Part Number
Description
Q'ty
❲ 17 ❳
Parts List : EDG2300
Fig.2 ENGINE UNIT (S/N 901112 and up)
❲ 18 ❳
EDG2300
Fig.2 ENGINE UNIT (S/N 901112 and up)
Key#
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
5602-12110
5500-12212
1850-12130
5500-13162
5500-13121
5500-13131
0263-90520
5602-15100
5602-15110
1601-15120
01252-30550
5500-15210
5600-15220
0263-90416
5600-21100
5500-21141
06030-06001
2169-21210
1850-21220
04065-02812
01252-30530
5600-41111
1100-41210
1101-41310
1260-41320
5500-41410
1101-41340
5600-42001
1650-43230
1000-43240
1400-51111
1140-51250
1970-51221
1140-51230
1970-51241
1140-21161
0263-90516
5600-52150
1650-43230
5601-71110
5501-71201
5500-71220
2616-71320
1900-72111
1900-72120
1260-71261
3310-72150
5500-72130
5990-75100
5990-75110
5990-75120
5990-75130
5990-75140
5890-75150
5990-75270
5990-75160
5990-75170
1861-75180
1490-75180
0263-90412
5501-81000
5602-06030
1850-81450
Description
CYLINDER
GASKET, base
BOLT M5x12
INSULATOR
GASKET, INSULATOR
GASKET, CARB
SCREW M5x20
MUFFLER ASSY
• MUFFLER
• ARRESTER
BOLT M5x55
GASKET, MUFFLER
PLATE
SCREW M4x16
CRANKCASE-C
GASKET
BEARING
SEAL
SEAL
RING
BOLT M5x30
PISTON
RING
PIN
RING
BEARING
WASHER
CRANKSHAFT-C
NUT
KEY
SHOE
SCREW
SPRING
WASHER
WASHER
CASE
SCREW M5x16
PLATE
NUT
ROTOR
COIL-A
• CORD, HIGH
• CAP
CAP
SPRING
SPACER
BOLT M4x25
GROMET
RECOIL-A
• CASE
• SPRING
• REEL
• RATCHET
• SPRING
• SCREW
• RETAINER
• WASHER
• ROPE
• KNOB
SCREW M4x16
CARBURETOR-A
• REBUILT KIT
• • BODY-A
Q'ty
Key#
Part Number
Description
Q'ty
1
1
2
1
1
1
2
1
1
1
2
1
1
1
1
1
2
1
1
1
4
1
2
1
2
1
2
1
1
1
2
2
1
2
2
1
4
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
–––––––––
–––––––––
–––––––––
–––––––––
–––––––––
–––––––––
5602-06020
–––––––––
–––––––––
–––––––––
–––––––––
1850-81490
1850-82520
1751-81510
5500-81251
1751-81240
1751-81130
5500-81160
1881-81140
5501-81153
1752-81110
5500-81120
1751-81180
1918-81170
1881-81130
1850-81530
0263-90560
1950-86120
5500-82102
1970-82190
5500-82131
5500-82140
2630-33610
5500-82171
5600-82202
5500-82221
5600-31110
0263-90520
5600-32100
1850-32160
1900-31410
5602-73110
5600-73200
5580-83100
5601-85000
5601-85200
5500-85220
5601-85230
5600-85240
5600-85250
5500-85300
5500-85400
1260-85460
5500-85510
5635-87110
0263-90520
1757-87200
1757-87220
0280-10504
01601-20513
5636-91120
5501-91160
• • • SCREEN
• • • VALVE
• • • SPRING
• • • SCREW
• • • PIN
• • • LEVER
• • GASKET KIT
• • • DIAPHRAGM-A
• • • GASKET
• • • DIAPHRAGM
• • • GASKET
• BODY
• COVER
• PUMP
• JET
• O-RING
• RING
• WASHER
• SWIVEL
• VALVE-A
• SCREW
• BRAKET
• NUT
• SCREW
• RING
• SCREW
SCREW M5x60
CLIP
BODY-A
• SLEEVE
• PLATE
• LEVER
• SCREW
ELEMENT
COVER-A
• KNOB
COVER
SCREW M5x20
COVER
SCREW M4x12
SCREW
SPARKPLUG Champion RCJ-6Y
SWITCH-A
CABLE COMP
TANK-A
• CAP-A
• • PACKING
• • HOLDER
• • CAP
• • VALVE
• PIPE-C
• FILTER-A
• CLIP
SCREW M5x16
PLATE
SCREW M5x20
JOINT
• BAND
NUT M5
WASHER
LABEL, RECOIL
LABEL, COVER
–
–
–
–
–
–
1
–
–
–
–
1
1
1
1
1
1
1
1
1
2
1
1
1
1
4
2
1
1
2
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
❲ 19 ❳
RedMax® PORTABLE GAS DRILL
MODEL EDG2300
2-YEAR LIMITED WARRANTY
For two (2) years [1 year if used commercially] from the date of original purchase of the model
EDG2300 unit, KOMATSU ZENOAH AMERICA INC. (the “Company”), through any RedMax®
dealer, will repair or replace, free of charge, for the original purchaser, any part found to be
defective in material and/or workmanship. This is the exclusive remedy.
The purchaser shall bear costs of transporting the model EDG2300 to and from the RedMax®
dealers.
This warranty does not apply to those units which have been damaged by accident,
mishandling, alteration, abuse, improper lubrication, the use of any parts or accessories other
than those specified by the Company, or other causes beyond our control.
This warranty does not cover those parts replaced for normal wear or harmless changes in
their appearance.
There are no other express warranties.
IMPLIED WARRANTIES including those of merchantability and fitness for a particular
purpose ARE LIMITED to one (1) year from the original purchase date. Liabilities for
incidental or consequential damages under any and all warranties are excluded.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
If you need to obtain information about the nearest service center, please call KOMATSU
ZENOAH AMERICA INC. at (770)-381-5147.
IMPORTANT: You will receive a Warranty Registration Card at time of purchase.
Please fill out the card and send it to RedMax / KOMATSU ZENOAH
AMERICA within seven (7) days.
Be sure to keep a copy for your records.
KOMATSU ZENOAH AMERICA INC.
4344 Shackleford Road Suite 500
Norcross, Georgia 30093
Débroussailleuse à deux lames réciproques
Modèle EDG2300
Garantie limitée à 2 ans
Par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou
remplacera gratuitement pour l'acheteur initial toute(s) pièce (s) se révélant de constitution
et/ou de montage défectueux pendant deux (2) ans en cas d’utilisation privée [un (1) an pour
toute autre utilisation] à compter de la date de livraison initiale d’une unité du modèle
EDG2300. Telles sont les limites de la garantie.
Le coût du transport de l'unité jusqu'au revendeur RedMax et depuis celui-ci sera à la charge
de l'acheteur.
La garantie ne s'applique pas aux unités endommagées par suite de: négligence dans la
mise en oeuvre des instructions spécifiées dans le manuel du propriétaire/de l'utilisateur en
vue d’une utilisation et d’un entretien correct, fausse manœuvre accidentelle, modification,
utilisation abusive, lubrification incorrecte, utilisation de pièces ou d’accessoires autres que
ceux spécifiés par la société, ou autres causes hors du contrôle de la société.
Cette garantie ne couvre pas les pièces remplacées en raison de leur usure normale ou de
changements d’apparence sans effets.
Il n'existe aucune autre garantie explicite.
Les garanties implicites, celles de négociabilité du produit et de son adaptabilité à un usage
défini incluses, sont limitées à deux (2) ans pour un usage privé [un (1) an pour toute autre
utilisation] à compter de la date initiale de livraison.
Certaines provinces n'autorisant pas les limitations à la durée des garanties implicites, ou les
exclusions ou limitations relatives aux dommages incidents ou conséquents, la limitation
indiquée ci-dessus peut ne pas vous être applicable.
Cette garantie vous donne des droits juridiques spécifiques, et vous pouvez également jouir
d’autres droits variant d'une province à l'autre.
Si vous désirez obtenir des informations sur le centre de service le plus proche, veuillez
appeler KOMATSU ZENOAH AMERICA INC. au (770)-381-5147
Note importante: vous recevrez une carte d'enregistrement de garantie au moment de
l'achat. Veuillez la remplir et l'adresser à RedMax / KOMATSU ZENOAH AMERICA sous sept
(7) jours en prenant soin de conserver une copie pour vous.
EPA PH1 EMISSION CONTROL LABEL
IMPORTANT ENGINE INFORMATION
THIS ENGINE CONFORMS TO US EPA
PH1 AND 1995-1999 CALIFORNIA EMISSION
REGULATIONS FOR ULGE ENGINES.
ENGINE FAMILY : TKZ025UB24RA
ENGINE DISPLACEMENT : 22.5cc
REFER TO OWNER'S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
KOMATSU ZENOAH CO.
RedMax Made in Japan
INFORMATION IMPORTANTECONCERNANT LE MOTEUR
Ce moteur conformc aux normcs U.S. EPA PH1 et
1995-1999 de la régulementation concernant la
pollution de l'air pour les petits moteurs tout-terrain.
Type de moteur : TKZ025UB24RA
Cylindrée du moteur : 22,5 cc
Se référer au Manuel de l'utilisateur pour
les spécifications d'entretien et les réglages.
KOMATSU ZENOAH CO.
RedMax Made in Japan
KOMATSU ZENOAH AMERICA INC.
4344 Shackleford Road Suite 500
Norcross, Georgia 30093
© Printed in Japan