M30620T-CPE Release Note

Rev.1.01
November 16, 2003
REJ10J0400-0101Z
M30620T-CPE Release Note
Setup Guide
For details, refer to…
- Read this before using November 16, 2003
Renesas Solutions Corp.
This document contains the information necessary for using this product. Be sure to read
this before using the product.
Introduction
The M30620T-CPE is a compact emulator for the M16C/62 Group M16C/62A with the realtime trace functions. This product consists of the following four products.
(1) Emulator M30620T-CPE
Compact emulator (board) for the M16C/62 Group M16C/62A.
(2) Emulator debugger M3T-PD30M V.1.10 Release 1
Control software specifically designed to control the M30620T-CPE emulator.
(3) C compiler M3T-NC30WA V.5.10 Release 1 (Entry version)
This version is a limited version of C compiler M3T-NC30WA V.5.10 Release 1. It
consists of ANSI-conforming C compiler NC30 and relocatable assembler AS30. For the
function limitations, refer to the release note of the M3T-NC30WA V.5.10 Release 1
(Entry version). Technical support and upgrade service are not provided with this
product. You can purchase the regular product without these limitations.
(4) Integrated Development Environment TM V.3.20A
Though emulator debugger M3T-PD30M and C compiler M3T-NC30WA can be used
independent of one another, working with integrated development environment TM
enables tool startups from TM, option setup via GUI and automatic file generation
(makefile). The integrated development environment TM normally packaged with the
product is no different from TM V.3.20A, but do not seek technical support as in the
case of the M3T-NC30WA (Entry version).
1.Check the contents
>>”Package Components”(bellow)
2.Register your M30620T-CPE
>>Hardware Tool User Registration Fax Sheet
3.Install emulator debugger M3T-PD30M
>>”Installing the Included Software Products”(next page)
4.Setup hardware
>>M30620T-CPE User’s Manual “Chapter 2.. Usage”
5.Turn on the emulator
>>M30620T-CPE User’s Manual “Chapter 2.. Usage”
6.Startup emulator debugger M3T-PD30M
>>M30620T-CPE User’s Manual “Chapter 2.. Usage”
7. C Compiler M3T-NC30WA
>>”Installing the Included Software Products”(next page)
8. InstallintegrateddevelopmentenvironmentTM
>>”Installing the Included Software Products”(next page)
9. For usage of each product
>>For the M30620T-CPE, refer to the “M30620T-CPE
User’s Manual”
>>For the M3T-PD30M, M3T-NC30WA and TM, refer to
each online manual which is installed with the product.
Package Components
Check to see if your product package contains all of the following items before using the
product.
1
M30620T-CPE emulator
1
2
Serial interface cable
1
3
Power cable
1
4
Hardware Tool User Registration Fax Sheet
1
5
M30620T-CPE Release Notes (English) [this document]
1
6
M30620T-CPE Release Notes (Japanese)
1
7
M30620T-CPE User’s Manual (English)
1
8
M30620T-CPE User’s Manual (Japanese)
1
1
9
CD-ROM - Emulator debugger PD30M Ver.1.10 Release 1
- C Compiler M3T-NC30WA V.5.10 Release 1 (Entry version)
- Integrated development environment TM V.3.20A
If any of these items are missing or found faulty, please contact your local distributor.
(1/2)
Operating Environment of the Included Software Products
Precautions for Using the Included Software Products
The operating environments of included software products are shown below.
Host machine
IBM PC/AT compatibles
OS
Windows 95, Windows 98, Windows 2000, Windows NT4.0
CPU
Pentium 166MHz
Memory
64M bytes or greater is recommended
(1) Emulator debugger M3T-PD30M
A release note is installed in the ¥PD30M¥RNOTE folder on the CD-ROM. Read it
before using the software.
(2) C Compiler M3T-NC30WA (Entry version)
A release note is installed in the ¥NC30WA¥RNOTE folder on the CD-ROM. Read it
before using the software.
Installing the Included Software Products
(1) Emulator debugger M3T-PD30M Installation
* If using Windows 2000 and Windows NT 4.0 as the host machine OS, have M3TPD30M installed by someone of administrator access level. Installation cannot be
completed by users with lower access level status.
* Working from Windows Explorer, start up "setup.exe" in the ¥PD30M¥W95E folder
on the CD-ROM. Then, install the software as instructed by the displayed messages.
(2) C Compiler M3T-NC30WA entry version Installation
* If the original version M3T-NC30WA is already installed, do NOT install the M3TNC30WA entry version included with this product and use the original M3TNC30WA.
* Working from Windows Explorer, start up "setup.exe" in the ¥NC30WA¥W95E folder
on the CD-ROM. Then, install the software as instructed by the displayed messages.
(3) Integrated Development Environment TM
A release note is installed in the ¥TM¥RNOTE folder on the CD-ROM. Read it before
using the software.
For the Latest Information
Visit our website (URL below). Please use this website providing the latest information of
Renesas tool products.
http://www.renesas.com/
To Contact Us
Fill in the text file the installer of the emulator debugger generates in the following
directory and email to your local distributor.
¥SUPPORT¥product name¥SUPPORT.TXT
(3) Integrated Development Environment TM Installation
* If the original version TM is already installed, do NOT install the TM included with
this product and use the original TM.
* Working from Windows Explorer, start up "setup.exe" in the ¥TM¥W95E folder on
the CD-ROM. Then, install the software as instructed by the displayed messages.
(4) Acrobat® Reader Installation
Electronic manuals are included in the software package. Acrobat Reader is needed to
view these manuals. Acrobat Reader is in the Acrobat folder on the CD-ROM, so install
it as necessary. The latest version of Acrobat Reader can be downloaded from Adobe
Systems website at http://www.adobe.com/.
Acrobat is a registered trademark of Adobe Systems Incorporated.
(2/2)