Atop ABLELink® Wireless Serial Server

Atop ABLELink® Wireless Serial Server
SW2001/ SW5001
Quick Start Guide
Version 1.1
Updated on September, 2006
Tel: 886-3-5508137
Fax: 886-3-5508131
www.atop.com.tw
Quick Start Guide Version 1.1
Atop ABLELink® Wireless Serial Server
SW2001/SW5001
Thank you for purchasing Atop SW2001/SW5001 Wireless Serial Server product. This document
intends to provide customers with brief descriptions about the product and to assist customers to
get started. For detail information and operations of the product, please refer to the product
user’s manual in the product CD or diskette.
1. Packaging
Please check your package contains the following items:
- Atop Wireless Serial Server x 1
- Mini DIN to DB-9 Cable x 1
- Wall mount kits x 2
- Atop Wireless Serial Server quick start guide x 1
- Product CD containing configuration utility x 1
2.Hardware Setup
Figure 1 shows the names of SW2001/SW5001 components. In the figure, the indicated
switch settings represent factory settings.
10/100M
Ethernet port for
settings
SMA rev. Antenna
Connector
Mini-DIN Connector
for Serial port
LED indication
for Wireless
Status
5-pin Terminal
Block for Serial
port
LED indication
for System
Status
3-pin Terminal
Block for Power
input
Reset button for
restart or factory
default
Figure 1. Nomenclature of SW2001/SW5001 Components
*Reset Button: Press Reset button continuously over 3 sec to reload factory default
1
Quick Start Guide Version 1.1
Atop ABLELink® Wireless Serial Server
SW2001/SW5001
LED Indications: The LEDs were indicated for SW2001/5001’s status
Name
Signal
Strength
WLAN
Color
Status
Description
Red(1)
ON
Its strength is poor, but the link is connected for the wireless
link
Yellow(2)
ON
Its strength is fair or good, the wireless link can supply a
good transfer channel
Green(2)
ON
Its strength is very good and the link is connected on best
status
Off
Wireless Link is Broken or No data transmit or receive via
wireless connectivity
Red
Blink
COM
Red
RUN
Red
Wireless Traffic be indicted for data transfer
Off
No data transmit or receive via serial port
Blink
Serial traffic be indicted for data transfer
OFF/ON
Blink
System is not ready or halt
System is running and LED is blink per 0.5 sec
Hardware installing procedure for initialization
Step 1: Pick the device up from the packaged box, connected Ethernet-link to LAN switch with
standard UTP cable.
Step 2: Attached the power wire to the device for 9~24V DC, and confirm the power polarity
carefully.
Step 3: Wait the device start up after 10~20 Seconds, and See the next section for software
installing
UL Notice for Power supplier
All the series of EH products are intended to be supplied by a Listed Power Unit marked with
“LPS”, “Limited Power Source” or “Class 2” and output rate 9~30VDC, 0.5A minimum. Or, use
the recommended power supply in “Optional Accessories.
3.Software Installing
Configure by monitor.exe utility
Use monitor.exe that comes with product CD or diskette to configure the network parameters of
SW2001/SW5001. Please refer to Appendix D Configuration Utility in the product user manual for
more details.
Step 1: Find new device and IP assignment
Step 2: User Monitor.exe for new device, get device’s current IP from table list
Step 3: Re-assigned IP, network mask and gateway if need with Monitor.exe.
Step 4: Configurative wireless, serial and connectivity mode by web browser or telnet tool.
Auto IP with DHCP
A DHCP server automatically assigns the IP address and network settings. SW2001/5001 supports
DHCP. It will supply for the unit with an IP address gateway address, and subnet mask. You may use
Monitor.exe software to search network information automatically by putting a check on Auto IP on
Dialog window.
Configure by web server
Step 1:Open web browser, type in the IP address of SW2001/SW5001 to be configured. Default
user name is admin and default password is null.
Step 2:Configure settings from web page links then click “Save Configuration” to save settings.
Step 3:Click on ”Restart” button to make the change effective
.
2
Quick Start Guide Version 1.1
Atop ABLELink® Wireless Serial Server
SW2001/SW5001
Configure by Telnet utility
Step 1:Telnet to SW2001/SW5001 using command “Telnet IP_address”. Default IP address is
10.0.50.100 and default password is null.
Step 2:SW2001/SW5001’s network, COM ports and wireless settings can be configured
individually.
Step 3:The connection status is shown from “AP version” column of monitoring tool (Monitor.exe)
.
4. Pin assignments
Pin assignments of Mini DIN connector is shown in the following table:
Mini-DIN
DB9
Pin#
RS-232
1
DCD
2
RXD
3
TXD
4
DTR
2 wire RS-485
4 wire RS-485
Tx+
Data+
5
Rx+
SG (Signal Ground)
6
DSR
7
RTS
8
CTS
Data-
RxTx-
Pin assignments for Terminal block for Serial and Power
RS-232
RS-485
RS-422
SG
GND
GND
GND
FG
GND
RTS/R-
RTS
Data-
R-
Vin-
0V
TxD/R+
TxD
Data-
R+
Vin+
9~30V
CTS/T-
CTS
T-
RxD/T+
RxD
T+
5-pin for serial connections
3-pin for Power input
Customer Services and Supports
1. Contact your local dealers or ATOP Technical Support Center at the following numbers.
+886-3-550-8137 (ATOP Taiwan)
+86-21-6495-6232 (ATOP China)
2. Report the errors via Atop’s Web site or E-mail account
www.atop.com.tw, service@atop.com.tw
www.atop.com.cn, service@atop.com.cn
3