Electrolux EGG690 Technical data

Gas hob
INSTR
UCTION BOOKLET
INSTRUCTION
Please read this instruction booklet before using the appliance
Mod. EGG 690
35685-4801
GB
Important Safety Information
You MUST read these warnings carefully before installing or using the hob. If you need
assistance, contact our Customer Care Department on 08705 950950
Installation
z
z
z
z
z
This hob must be installed by qualified personnel,
according to the manufacturer’s instructions and to
the relevant British Standards.
Any gas installation must be carried out by a
registered CORGI installer.
Remove all packaging before using the hob.
Ensure that the gas and electrical supply complies
with the type stated on the rating plate, located near
the gas supply pipe.
Do not attempt to modify the hob in any way.
Service
z
This hob should only be repaired or serviced by an
authorised Service Engineer and only genuine
approved spare parts should be used.
Environmental Information
z
z
After installation, please dispose of the packaging with
due regard to safety and the environment.
When disposing of an old appliance, make it unusable,
by cutting off the cable.
Child Safety
z
z
z
z
This hob is designed to be operated by adults. Do
not allow children to play near or with the hob.
The hob gets hot when it is in use.
Children should be kept away until it has cooled.
Children can also injure themselves by pulling pans
or pots off the hob.
During Use
z
z
z
z
z
z
z
z
z
z
2
This hob is intended for domestic cooking only. It is
not designed for commercial or industrial purposes.
When in use a gas cooking appliance will produce
heat and moisture in the room in which it has been
installed. Ensure there is a continuous air supply,
keeping air vents in good condition or installing a
cooker hood with a venting hose.
When using the hob for a long period of time, the
ventilation should be improved, by opening a window
or increasing the extractor speed.
Do not use this hob if it is in contact with water.
Do not operate the hob with wet hands.
Ensure the control knobs are in the ‘OFF’ position
when not in use.
When using other electrical appliances, ensure the
cable does not come into contact with the hot surfaces
of the cooking appliance.
Unstable or misshapen pans should not be used on
the hob as unstable pans can cause an accident by
tipping or spillage.
Never leave the hob unattended when cooking with
oil and fats.
Never use plastic or aluminium foil dishes on the hob.
Perishable food, plastic items and areosols may be
affected by heat and should not be stored above or
below the hob unit.
Keep this instruction book for future reference
and ensure it is passed on to any new owner.
Guide to Use the instructions
The following symbols will be found in the text to guide
you throughout the Instructions:
Safety Instructions
)
Step by step instructions for an operation
Hints and Tips
Enviromental information
This appliance complies with the following
E.E.C. Directives:
* 73/23 - 90/683 (Low VoltageDirective);
* 93/68 (General Directives);
* 89/336 (Electromagnetical Compatibility
Directive);
* 90/396 (Gas Appliances),
and subsequent modifications
Contents
For the User
For the Installer
Important Safety Information
2
Instructions for the Installer
7
Description of the Hob
3
Important safety requirements
8
Operation
4
Installation
8
Maintenance and Cleaning
4
Building In
9
Something Not Working?
5
Electrical connections
10
Service and Spare Parts
5
Wiring Diagram
11
Guarantee Conditions
6
Fault Finding
11
Commissioning
13
Conversion from Natural Gas to LPG
14
Description of the Hob
3
1
3
5
4
2
1. Hob top
2. Rapid Burner
3. Semi-rapid Burner
4. Auxiliary Burner
5. Control knobs
3
Operation
Hob burners
)
z
z
z
To light a burner:
push in the relevant control and turn it to maximum
position;
then adjust the flame as required.
If the burner does not ignite, turn the control knob to
zero, and try again.
If you use a saucepan which is smaller than the
recommended size, the flame will spread beyond
the bottom of the vessel, causing the handle to
overheat.
Take care when frying food in hot oil or fat, as
the overheated splashes could easily ignite.
As soon as a liquid starts boiling, turn down the
flame so that it will barely keep the liquid
simmering.
To ensure maximum burner efficiency, you should only
use pots and pans with a flat bottom fitting the size of
the burner used (see table).
Burner
minimum
diameter
Large (rapid)
Medium (semi-rapid)
Small (auxiliary)
160 mm.
120 mm.
80 mm.
maximum
diameter
240 mm.
220 mm.
160 mm.
If the control knobs become difficult to turn, please
contact your local Service Force Centre.
Maintenance and Cleaning
Before any maintenance or cleaning can be carried
out, you must DISCONNECT the hob from the
electricity supply.
The hob is best cleaned whilst it is still warm, as
spillage can be removed more easily than if it is
left to cool.
Pan Supports
The pan supports are dishwasher proof.
If necessary, remove stubborn stains using a paste
cleaner. Never use steel wool pads or acids.
The Hob Top
Regularly wipe over the hob top and the aluminium frame
using a soft cloth well wrung out in warm water to which
a little washing up liquid has been added. Avoid the use
of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that a cleaning product such as Hob Brite
or Bar Keepers Friend is used.
The Burners
The burner caps and crowns can be removed for cleaning.
The cap and crown of each burner are secured with two
screws. To separate the two pieces, lift the crown, turn it
upside down, then undo the two fixing screws as shown
in the diagram.
After cleaning, reassemble the two parts and refit the
cap on its correct position on the burner.
Wash the burner caps and crowns using hot soapy water,
and remove marks with a mild paste cleaner. A well
moistened soap impregnated steel wool pad can be used
with caution, if the marks are particularly difficult to
remove.
After cleaning, be sure to wipe dry with a soft cloth.
4
FO 2265
Something Not Working?
If the hob is not working correctly, please carry out the following checks before contacting your local Service Force
Centre.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation,
a charge will be made even if the appliance is under guarantee.
SYMPTOM
SOLUTION
„ There is no spark when lighting the gas
‹ Check that the unit is plugged in and the electrical
supply is switched on
‹ Check that the RCCB has not tripped (if fitted)
‹ Check the mains fuse has not blown
‹ Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
„ The gas ring burns unevenly
‹ Check the main jet is not blocked and the burner
crown is clear of food particles.
‹ Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
If after all these checks, your hob still does not operate
correctly, contact your local Service Force Centre.
Please note that it will be necessary to provide proof of
purchase for any in-guarantee service calls.
In-guarantee customers should ensure that the
above checks have been made as the engineer will
make a charge if the fault is not a mechanical or
electrical breakdown.
Service and Spare Parts
In the event of your appliance requiring service, or if you
wish to purchase spare parts, please contact your local
Electrolux Service Force Centre by telephoning:
0870 5 929929
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
For the address of your local Service Force Centre and
further information about Service Force, please visit the
website at www.serviceforce.co.uk
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not
Working.”
When you contact the Service Force Centre you will
need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found
on the rating plate)
5. The purchase date
5
Customer Care Department
For general enquiries concerning your Electrolux
appliance or for further information on Electrolux products,
please contact our Customer Care Department by letter
or telephone at the address below or visit our website at
www.electrolux.co.uk
Customer Care Department
ELECTROLUX
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel. 08705 950950 (*)
* calls to this number may be recorded for training purposes.
Guarantee Conditions
Electrolux Guarantee
conditions
*
We, Electrolux, undertake that if, within 12 months of
the date of the purchase, this Electrolux appliance or
any part thereof is proved to be defective by any reason
only of faulty workmanship or materials, we will, at our
option, repair or replace the same FREE OF ANY
CHARGE for labour, materials or carriage on condition
that:
* The appliance has been correctly installed and used
only on the gas and electricity supply stated on the
rating plate.
* The appliance has been used for normal domestic
purpose only, and in accordance with the
manufacturer's instructions.
* The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any person
not authorised by us.
* All service work under this guarantee must be
undertaken by a Service Force Centre.
* Any appliance or defective part replaced shall
become the Company's property.
* This guarantee is in addition to your statutory and
other legal rights.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside these
hours, in which case a premium will be charged.
*
Appliances found to be in use within a commercial or
similar environment, plus those which are the subject
to rental agreements.
Products of Electrolux manufacture which are not
marketed by Electrolux.
European Guarantee
If you should move to another country within Europe then
your guarantee moves with you to your new home
subject to the following qualifications:
* The guarantee starts from the date you first
purchased your product.
* The guarantee is for the same period and to the same
extent for labour and parts as exist in the new country
of use for this brand or range of products.
* This guarantee relates to you and cannot be
transferred to another user.
* Your new home is within the European Community
(EC) or European Free Trade Area.
* The product is installed and used in accordance with
our instructions and is only used domestically, i.e. a
normal household
* The product is installed taking into account
regulations in your new country.
Exclusions
Before you move, please contact your nearest Customer
Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service
Organisation is aware of your move and able to look after
you and your appliances.
This guarantee does not cover:
* Damage or calls resulting from transportation,
improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
* Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliance
outside the United Kingdom.
France
Germany
Italy
Sweden
UK
6
Senlis
Nürnberg
Pordenone
Stockholm
Slough
+33 (0) 3 44 62 20 13
+49 (0) 800 234 7378
+39 (0) 800 117511
+46 (0) 20 78 77 50
+44 (0)1753 219898
Instructions for the Installer
Engineers technical data
Overall dimensions
Width:
615,5 mm (front edge)
580 mm (rear edge)
Depth:
510 mm
Ignition HT Spark
Spark Generator
Ispra Control's BF 50046
230-240V 0.6 YA T 120
Fixed
Spark Gap
Semi-rapid Burner
Heat Input
Cut out dimensions
Width:
Depth:
550 mm
470 mm
Rapid Burner
Heat Input
Supply connections
2.9 kW Natural Gas (9895 BTU/HR)
2.7 kW L.P.G. (9212 BTU/HR)
Auxiliary Burner
Heat Input
Gas:
R 1/2 inch (1/2 inch male) Rear right hand corner
1.9 kW (6483 BTU/HR)
1.0 kW (3412 BTU/HR)
VALUE = 37.78 MJ/m3
CHARACTERISTICS
Ws - 50.7 MJ/ m3
VALUE = 49.92 MJ/Kg
LPG GAS
28-30/37 mbar
NATURAL GAS
20 mbar
TYPE OF
GAS
Electric:
230-240V 50Hz supply, 3 core flexible cable with non
rewireable plug fitted with a 3 amp cartridge fuse.
BURNER
POSITION
RAPID
(large)
SEMI-RAPID
(medium)
AUXILIARY
(small)
MAX
MIN
MAX
MIN
MAX
2.9
0.65
1.9
0.45
1.0
0.33
0.276
0.062
0.181
0.043
0.095
0.031
119
Adjust.
96
Adjust.
70
Adjust.
NOMINAL THERMAL
POWER kW
2.7
0.65
1.9
0.45
1.0
0.33
NOMINAL FLOW
RATE g/h
195
46.8
137
32.4
72
23.8
86
40
71
32
50
28
NOMINAL THERMAL
POWER kW
NOMINAL FLOW
RATE m3/h
NOZZLE REFERENCE
1/100 mm
NOZZLE REFERENCE
1/100 mm
Burner
Dia. Tap By-pass
1/100 mm
Auxiliary
28
Semi-rapid
Rapid
32
40
MIN
APPLIANCE CLASS:
3
APPLIANCE CATEGORY:
II2H3+
APPLIANCE GAS SUPPLY: Natural gas G20 / 20mbar
Aeration adjustment none
7
Important safety requirements
This hob must be installed in accordance with the Gas Safety (Installation and
Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current
Edition).
Detailed recommendations are contained in the following British Standards Codes
Of Practice: B.S. 6172/ B.S. 5440, Part 2 and B.S. 6891 Current Editions.
The hob should not be installed in a bed sitting room with a volume of less than
20 m3. If it is installed in a room of volume less than 5 m3 an air vent of effective
area of 110 cm2 is required. If it is installed in a room of volume between 5 m3 and
10 m3 an air vent of effective area of 50 cm2 is required, while if the volume
exceeds 11 m3 no air vent is required.
However, if the room has a door which opens directly to the outside no air vent is
required even if the volume is between 5 m3 and 11 m3.
If there are other fuel burning appliances in the same room, B.S. 5440 Part 2
Current Edition, should be consulted to determine the requisite air vent
requirements.
FITTING THE GAS HOB
WITHOUT A COOKER HOOD ABOVE
700 mm
400 mm
55
50 m
mm
m
100
400 mm
mm
50 m
m
FO 0812
Location
The hob may be located in a kitchen, a kitchen/diner or bed sitting room, but not
in a bathroom, shower room or garage.
Before making the cut out in the worktop ensure that the edges of the hob that
are to be near either a side or rear wall have a minimum distance of 55 mm.
between the edge of the hob and the wall.
The minimum distance combustible material can be fitted above the hob is 400
mm. If it is fitted below 400 mm. a space of 50 mm. must be allowed from the
edges of the hob.
The minimum distance combustible material can be fitted directly above the hob
is 700 mm. A minimum distance of 100 mm. must be left between the side edges
of the hob and any adjacent cabinets or walls.
FITTING THE GAS HOB
WITH A COOKER HOOD ABOVE
600 mm
650 mm
400 mm
55
50 m
mm
m
100
400 mm
mm
50 m
m
Installation
IMPORTANT
This hob must be installed by qualified
personnel to the relevant British Standards.
Any gas installation must be carried out by a
registered CORGI installer.
The manufacturer will not accept liability, should
the above instructions or any of the other safety
instructions incorporated in this book be
ignored.
FO 0813
WHEN THE HOB IS FIRST INSTALLED
Once the hob has been installed, it is important
to remove any protective materials, which were
put on in the factory.
On the end of the shaft, which includes the G 1/2"
threaded elbow, adjustment is fixed so that the washer
is fitted between the components as shown in the
diagram. Screw the parts together without using excessive
force.
Gas Connection
Connection to the gas supply should be with either rigid
or semi-rigid pipe, i.e. steel or copper.
The connection should be suitable for connecting to R
1/2” (1/2 BSP male thread).
When the final connection has been made, it is essential
that a thorough leak test is carried out on the hob and
installation. Ensure that the main connection pipe does
not exert any strain on the hob.
It is important to install the elbow correctly, with
the shoulder on the end of the thread, fitted to the
hob connecting pipe.
Failure to ensure the correct assembly will cause
leakage of gas.
8
FO 0814
FO 0264
A) End of shaft with nut
B) Washer
C) Elbow
Cut Out Size
The dimensions of the cut-out are given in the diagram.
1
FLEX
OUTLET
30
470
ON/OFF SWITCH
550
FO 2098
Building In
FO 0763
ON/OFF SWITCH
Building over a kitchen unit
with door
Proper arrangements must be taken in designing the
furniture unit, in order to avoid any contact with the
bottom of the hob which can be heated when it is
operated. The recommended solution is shown in
diagram 3.
The panel fitted under the hob ("a") should be easily
removable to allow easy access if technical
assistance is needed. The space behind the kitchen
unit ("b") can be used for connections.
Fitting the hob to the
worktop
Before fitting the hob into the cut out, an adhesive
seal must be fitted to the underside outside edge
(diagram 4) of the hob. It is essential that no gaps
are left in this seal in order to prevent spillage near
the hob seeping into the cabinet below.
1) Remove the pan supports, the burners caps
and crowns and turn the hob upside down,
taking care the ignition candles are not
damaged in this operation.
2) Place the sealing gasket all around the
glass top edge as shown in diagram 4.
3) Fit the hob in the cut out and push it down
until the glass top and the working top make
contact, as shown in diagram 5.
a
60
20 min
If the hob is to be installed above a cupboard or drawer
it will be necessary to fit a heat resistant board below
the base of the hob on the underside of the work
surface.
It is also recommended to carry out the electrical
connection to the hob as shown in diagrams 1 and 2.
30
Building over a cupboard or
drawer
3
2
b
FLEX
OUTLET
FO 1013
FO 0764
Dimensions are given in mm.
4
FO 2108
FO 2107
5
A
)
a) Sealing gasket
9
Electrical connections
Any electrical work required to install this hob
should be carried out by a qualified electrician or
competent person, in accordance with the current
regulations.
THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability should these
safety measures not be observed.
This hob is designed to be connected to a 230-240V
50Hz AC electrical supply.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the hob rating
plate. The rating plate is located on the bottom of the
hob. A copy is attached on the back cover of this book.
The hob is supplied with a 3 core flexible supply cord
incorporating a 3amp plug fitted. In the event of having to
change the fuse, a 3amp ASTA approved (BS 1362) fuse
must be used.
Should the plug need to be replaced for any reason, the
wires in the mains lead are coloured in accordance with
the following code:
Green and Yellow - Earth
Blue
- Neutral
Brown
- Live
— Connect the green and yellow (earth) wire to
the terminal in the plug which is marked with
Permanent Connection
In the case of a permanent connection, it is necessary
that you install a double pole switch between the hob
and the electricity supply (mains), with a minimum gap
of 3 mm. between the switch contacts and of a type
suitable for the required load in compliance with the
current electric regulations.
The switch must not break the yellow and green earth
cable at any point.
Ensure that the hob supply cord does not
come into contact with surfaces with
temperatures higher than 50 deg. C.
Supply cable replacement
The cable used to connect the hob to the electrical supply
must comply to the specifications given below.
Min. size Cable/flex
0.75 mm2
)
the letter 'E' or the earth symbol
or coloured
green and yellow.
NOTE:
The earth wire should be about 2 cm. longer
than the live and neutral wires.
— Connect the blue (neutral) wire to the terminal
in the plug which is marked with the letter 'N'
or coloured black.
— Connect the brown (live) wire to the terminal in
the plug which is marked with the letter 'L' or
coloured red.
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure over
the outer sheath.
A cut off plug inserted into a 13 amp socket is
a serious safety (shock) hazard. Ensure that
the cut off plug is disposed of safely.
10
FO 0390
Cable / flex type
Fuse
H05 V2V2-F (T90)
3A
Wiring Diagram
N
220
240
1
2
3
0
4
2
A. IGNITOR SWITCH
1
Brown
B. IGNITOR UNIT
L
Fault Finding
Preliminary Electrical Systems
Check
Green
Yellow
Earth Wire
Green/Yellow
START
Isolate appliance
and carry out:
A: Earth Continuity
check.
( )
E( )
FUSE
Blue
SOCKET
(face view)
PLUG (with cover
removed)
Neutral Wire
Blue
N
L
Blue
Brown
Green
Yellow
NO
YES
Carry out:
C: Polarity check.
Has inlet fuse blown?
NO
YES
Carry out:
D: Resistance to
Earth check.
Electricity supply
should now be
satisfactory.
A. EARTH CONTINUITY CHECK - Appliance must be
electrically disconnected - meter set on Ω (Ohms) x
1 scale and adjust zero if necessary.
a) Test leads from any appliance earth point to earth
pin on plug. Resistance should be less than 0.1
Ω (Ohm), check all earth wires for continuity and
all contacts are clean and tight.
Inlet wiring
faulty.
Rectify any
fault.
B. INSULATION CHECK - Appliance electrically
disconnected, all switches ON.
a) meter set on Ω (Ohms) x 1 scale.
Test leads from L to N in appliance terminal block.
If meter reads «0» then there is a short circuit.
Isolate appliance and
carry out:
B: Insulation check.
Rectify any fault
including replacing
fuses as necessary.
b) meter set on Ω (Ohm) x 100 scale.
Repeat test with leads from L to E. If meter reads
less than ∞ (infinity) there is a fault.
NOTE - Should it be found that the fuse has failed
but no fault is indicated - a detailed continuity check
(i.e. by disconnecting and checking each
component) is required to trace the faulty component.
It is possible that a fault could occur as a result of
local burning/arcing but no fault could be found under
test. However a detailed visual inspection should
reveal evidence of burning around the fault.
11
Ignition System / Gas Ignition
Ignitor does not spark
YES
Check gas supply at
burner
NO
Check plug top fuse and
replace if necessary
Light burner manually
Check polarity and earth
continuity of supply point
Check by pass simmer
adjusted
Check position of the
electrode
Check earth continuity
of appliance
Check continuity from 'N' on the
mains connector block and "O" on
the ignitor unit
Check continuity from 'L' on the
mains connector block and the
taps ignition switches
Check continuity from ignition
switches connector to ignitor unit
Check continuity from the tip of
each electrode to the terminals 1
to 4 on the ignitor unit
Check for breaks in the insulation
of the HT leads
Change the taps
ignition switches
Change the ignitor unit
12
Check fitting of burners
Commissioning
When the hob has been fully installed it will be necessary
to check the minimum flame setting. To do this, follow
the procedure below.
-
Turn the gas tap to the MAX position and ignite.
-
Set the gas tap to the MIN flame position then turn
the control knob from MIN to MAX several times. If
the flame is unstable or is extinguished follow the
procedure below.
Procedure:
)
Re-ignite the burner and set to MIN.
Remove the control knob.
To adjust, use a thin bladed screwdriver and turn
the adjustment screw (see diagram) until the flame
is steady and does not extinguish, when the knob
is turned from MIN to MAX. Repeat this procedure
for all burners.
Minimum adjustment screw
Pressure Testing
)
Remove left hand pan support and front left burner
cap and crown.
Fit manometer tube over the injector.
Turn on the burner gas supply and ignite another
burner.
The pressure reading should be nominally 20mbar
and must be between 17 mbar and 25mbar.
Turn off the burner supplies.
13
Conversion from Natural Gas to
LPG
It is important to note that this model is designed for
use with natural gas but can be converted for use with
butane or propane gas providing the correct injectors
are fitted. The gas rate is adjusted to suit.
Method
•
•
•
•
Ensure that the gas taps are in the 'OFF' position
Isolate the hob from the electrical supply
Remove all pan supports, burner caps, rings, crowns
and control knobs.
With the aid of a 7mm box spanner the burner injectors
can then be unscrewed and replaced by the
appropriate LPG injectors.
14
To adjust the gas rate
With the aid of a thin bladed screwdriver completely
tighten down the by pass adjustment screw, see the
illustration under the heading ‘Commissioning’.
Upon completion affix the replacement rating plate on
the under side of the hob.
IMPORTANT
The replacement/conversion of the gas hob should only
be undertaken by a competent person.
15
Grafiche MDM - Forlì
CUSTOMER CARE
Electrolux
55-77 High Street
Slough
Berkshire, SL1 1DZ
Tel: 08705-950950
© Electrolux plc 2003
The Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than
55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and
lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
10/03