user manual
Dishwasher
EX601SC
2 electrolux
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
Contents
Safety information
Product description
Control panel
First use
Use of rinse aid
Daily use
Load cutlery and dishes
Use of detergent
Tablet function
Select and start a washing programme
2
4
5
7
7
8
9
11
12
13
Unloading the dishwasher
Washing programmes
Care and cleaning
What to do if…
Technical data
Hints for test institutes
Installation
Water connection
Electrical connection
Environment concerns
Warranty
14
15
16
17
19
19
20
22
23
24
25
Subject to change without notice
Safety information
In the interest of your safety and to ensure the correct use, before installing
and first using the appliance, read this
user manual carefully, including its hints
and warnings. To avoid unnecessary
mistakes and accidents, it is important
to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these
instructions and make sure that they remain with the appliance if it is moved or
sold, so that everyone using it through
its life will be properly informed on appliance use and safety.
Correct use
• This dishwasher is only intended for washing household utensils suitable for machine washing.
• Do not put any solvents in the dishwasher.
This could cause an explosion.
• Knives and other items with sharp points
must be loaded in the cutlery basket with
their points down or placed in a horizontal
position in the upper basket.
• Only use products (detergent, cleaners,
rinse aid etc.) suitable for dishwashers.
• Hot steam may escape. Avoid opening the
door whilst the appliance is in operation.
• Do not take any dishes out of the dishwasher before the end of the washing cycle.
• If the supply cord is damaged, it must be
replaced by the manufacturer or its service
agent or a similarly qualified person in order to avoid a hazard.
• This product must be serviced only by an
authorized service engineer, and only genuine spare parts must be used.
General safety
• Dishwasher detergents are very alkaline
and extremely dangerous if swallowed. Be
careful to: keep them away from your eyes
and skin, keep children from the dishwasher when the door is opened and only
put detergent in the dispenser when you
are ready to wash.
• Make sure that the detergent receptacle in
the dispenser is empty after the completion of a wash cycle.
• Water in the dishwasher is not for drinking
purposes. Detergent residue may still be
present in your machine.
• Ensure that the door of the dishwasher is
always closed when it is not being loaded
or unloaded. In this way you will avoid anybody tripping over the open door and hurting themselves.
• Do not sit or stand on the open door.
electrolux 3
Child safety
• This appliance is not intended for use by
young children or infirm persons unless
they have been adequately supervised by
a responsible person to ensure that they
can use the appliance safety.
• Young children must be supervised to ensure that they do not play with the appliance.
• Keep all packaging well away from children. There is a risk of suffocation.
• Keep all detergents in a safe place out of
children’s reach.
• Keep children well away from the dishwasher when the door is open.
Installation
• Check your dishwasher for any transport
damage. Never connect a damaged machine. If your dishwasher is damaged contact your supplier.
• All packaging must be removed before
use.
• Any electrical and plumbing work required
to install this appliance must be carried out
by a qualified and competent person.
• For safety reasons it is dangerous to alter
the specifications or attempt to modify this
product in any way.
• Never use the dishwasher if the electrical
supply cable and water hoses are damaged; or if the control panel, work top or
plinth area are damaged such that the inside of the appliance is freely accessible.
Contact your local Customer Care Centre,
in order to avoid hazard.
• All sides of the dishwasher must never be
drilled to prevent damage to hydraulic and
electric components.
Warning! FOR ELECTRICAL AND
WATER CONNECTIONS CAREFULLY
FOLLOW THE INSTRUCTIONS GIVEN
IN THE SPECIFIC PARAGRAPHS.
4 electrolux
Product description
9
1 Top shower
2 Upper basket
3 Air vent and water hardness dial (the dial
is only functional for dishwashers with a
water softener)
4 Detergent dispenser
5
6
7
8
9
Rinse aid dispenser
Rating plate
Filters
Lower spray arm
Upper spray arm
electrolux 5
Control panel
1.
2.
3.
4.
5.
6.
On/Off button
Digital display
Programme selection buttons
Delay start button
Indicator lights
Function buttons
Indicator lights
Tablet function
Indicates the activation/deactivation of the
'Tablet function' (refer
to 'Tablet function' ).
Rinse aid
Comes on when the
rinse aid has run out.
1)
End
Comes on when a
washing programme
has ended.
1) The rinse aid indicator light never comes on
while a washing programme is running even if
filling with rinse aid is necessary.
The digital display
The digital display indicates:
• the approximate remaining time of the running programme,
• activation/deactivation of the rinse aid dispenser ( ONLY with the 'Tablet function'
active),
• the end of a washing programme (the digital display shows a zero),
• the countdown for the delay start,
• fault codes concerning malfunction of the
dishwasher,
• if the audible signals are activated/deactivated.
Function buttons
The following functions can be set using
these buttons:
• cancelling a washing programme or a delay start in progress,
• activation/deactivation of the 'Tablet function',
• activation/deactivation of the rinse aid dispenser when the 'Tablet function' is active,
• activation/deactivation of the audible signals.
Setting mode
Press the On/Off button; if ALL programme
button lights are on, the appliance is in setting mode.
Always remember that when performing
the following operations:
– selecting a washing programme,
– activating/deactivating the rinse aid,
– activating/deactivating the audible
signals,
the appliance MUST be in setting mode.
Press the On/Off button; if a programme button light is on, the last performed or selected
programme is still set. In this case, to return
to setting mode, the programme has to be
cancelled.
6 electrolux
To cancel a set programme or a
programme in progress
Simultaneously press and hold the two function buttons B and C until all the programme
button lights come on. The programme has
been cancelled and the machine is now in
setting mode.
Audible signals
Audible signals have been introduced to help
indicate which operations the dishwasher is
performing:
– end of the washing programme,
– intervention of an alarm due to malfunction
of the machine.
Factory setting: audible signals activated
It is possible to deactivate the audible
signals.
Deactivation/activation of the audible
signals
1. Press the On/Off button. The dishwasher
must be in setting mode.
2. Simultaneously press and hold function
buttons B and C until the lights of function
buttons A , B and C start flashing.
3. Press function button C , the lights of
function buttons A and B go off while the
light of function button C continues to
flash. The digital display shows the current level.
Audible signals deactivated
Audible signals activated
4. To change the setting, press function
button C again; the digital display shows
the new setting.
5. 5. To memorize the operation, switch off
the dishwasher.
electrolux 7
First use
Before using your dishwasher for the first
time:
• Ensure that the electrical and water connections comply with the installation instructions.
• Remove all packaging from inside the appliance.
• Fill the rinse aid dispenser.
If you want to use the multi benefit
tablets set the 'Tablet' function. (Refer to 'Tablet function').
Use of rinse aid
Warning! Only use branded rinse aid for
dishwashers.
Never fill the rinse aid dispenser with any
other substances (e.g. dishwasher
cleaning agent, liquid detergent). This
would damage the appliance.
Rinse aid ensures thorough rinsing, and
spot and streak free drying.
Rinse aid is automatically added during
the last rinse.
1. Open the container by pressing the release button (A).
The dispenser holds about 110 ml of rinse
aid, which is sufficient for between 16 and
40 washing cycles, depending upon the
dosage setting.
3. Ensure that the lid is closed after every
refill.
Clean up any rinse aid spilt during filling
with an absorbent cloth to avoid excess
foaming during the next wash.
2. Add the rinse aid in the container. The
maximum level for filling is indicated by
"max".
According to the finish and drying results obtained, adjust the dose of rinse aid by means
of the 6 position selector (position 1 minimum
dosage, position 6 maximum dosage).
The dose is factory set in position 4.
Increase the dose if there are drops of water
or lime spots on the dishes after washing.
Reduce it if there are sticky whitish streaks
on the dishes or a bluish film on glassware or
knife blades.
8 electrolux
Daily use
• Check if it’s necessary to refill with rinse
aid.
• Load cutlery and dishes into the dishwasher.
• Add required amount of detergent just prior to wash.
• Select a wash programme suitable for the
cutlery and dishes.
• Start the wash programme.
Helpful hints and tips
Sponges, household cloths and any object
that can absorb water may not be washed in
the dishwasher.
• Before loading the dishes, you should:
– Remove all left over food and debris.
– Soften remnants of burnt food in pans
• When loading the dishes and cutlery,
please note:
– Dishes and cutlery must not impede the
rotation of the spray arms.
– Load hollow items such as cups,
glasses, pans, etc. with the opening
downwards so that water cannot collect
in the container or a deep base.
– Dishes and items of cutlery must not lie
inside one another, or cover each other.
– To avoid damage to glasses, they must
not touch.
– Lay small objects in the cutlery basket.
• Plastic items and pans with non stick coatings have a tendency to retain water
drops; these items will not dry as well as
porcelain and steel items.
• Light items (plastic bowls etc.) must be
loaded in the upper basket and arranged
so they do not move.
For washing in the dishwasher the following cutlery and dishes
are not suitable:
are of limited suitability:
• Cutlery with wooden, horn, china or mother-of- • Only wash stoneware in the dishwasher if it is
pearls handles.
specially marked as being dishwasher-safe by
• Plastic items that are not heat resistant.
the manufacturer.
• Older cutlery with glued parts that are not tem- • Glazed patterns may fade if machine washed
perature resistant.
frequently.
• Bonded cutlery items or dishes.
• Silver and aluminium parts have a tendency to
• Pewter or copper items.
discolour during washing: Residues, e.g. egg
• Lead crystal glass.
white, egg yolk and mustard often cause dis• Steel items prone to rusting.
colouring and staining on silver. Therefore al• Wooden platters.
ways clean left-overs from silver immediately, if
• Items made from synthetics fibres.
it is not to be washed straight after use.
electrolux 9
Load cutlery and dishes
The lower basket
The lower basket is designed to take saucepan, lids, plates, salad bowls, cutlery etc.
Service dishes and large lids should be arranged around the edge of the basket, ensuring that the spray arms can turn freely.
horizontally in the upper basket. Take
care when loading or unloading sharp
items such as knives.
Forks and spoons should be placed in the
removable cutlery basket with the handles
facing downwards and the knives with their
handles facing upwards.
If the handles protrude from the bottom of the
basket, obstructing the lower spray arm, load
the cutlery with the handles facing upwards.
Mix spoons with other cutlery to prevent
them from sticking together.
To make loading of the cutlery basket easier,
lower the cutlery basket handle.
The rows of prongs in the lower basket can
lie flat to allow you to load pots, pans and
bowls.
The cutlery basket
Long bladed knives stored in an upright
position are a potential hazard. Long
and/or sharp items of cutlery such as
carving knives must be positioned
For best results we recommend that you use
the cutlery grids.
If the size and dimensions of the cutlery do
not allow the use of the grids, they can be
easily hidden.
10 electrolux
The cutlery basket is in two parts which can
be separated to give greater loading flexibility. To separate the two parts, slide them horizontally in opposite directions and pull them
apart.
To reassemble, reverse the procedure.
The upper basket
The upper basket is designed for saucers,
salad bowls, cups, glasses, pots and lids.
Arrange items on and underneath the cup
racks so that water can reach all surfaces.
Glasses with long stems can be placed upside down in the cup racks.
For taller items, the cup racks can be folded
upwards.
The central rows of prongs can be easily lowered to improve loading flexibility.
Before closing the door, ensured that
the spray arms can rotate freely.
electrolux 11
Adjusting the height of the upper basket
If washing very large plates you can load
them in the lower basket after moving the
upper basket to the higher position.
Maximum height of the dishes in the lower
basket
With upper basket
raised
31 cm
With upper basket
lowered
27 cm
To move to the higher position proceed
as follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards until the
mechanism is engaged and the basket is
stable.
To lower the basket to the original position proceed as follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards and then
allow the mechanism to drop back down
slowly, keeping hold of it.
Caution! Never lift or lower the basket
on one side only.
When the basket is in the higher position:
• do not load cups on the cup racks,
• make sure that the cup racks are lied
down and not folded upwards.
After loading your machine always
close the door, as an open door can
be a hazard.
Use of detergent
Only use detergents specifically designed for use in dishwashers.
Please observe the manufacturer’s dosing and storage recommendations as
stated on the detergent packaging.
Using no more than the correct amount
of detergent contributes to reducing pollution.
Fill with detergent
1. Open the lid.
2. Fill the detergent dispenser (1) with detergent. The marking indicates the dosing
levels:
20 = approximately 20 g of detergent
30 = approximately 30 g of detergent.
12 electrolux
4. Close the lid and press until it locks in
place.
1
2
Detergent tablets from different manufacturers dissolve at different rates. For
this reason, some detergent tablets do
not attain their full cleaning power during
short washing programmes. Therefore,
please use long washing programmes
when using detergent tablets, to ensure
the complete removal of detergent residuals.
3. All programmes with prewash need an
additional detergent dose (5/10 g) that
must be placed in the prewash detergent
chamber (2).
This detergent will be used during the
prewash phase.
When using detergent tablets; place the
tablet in compartment (1)
Tablet function
This appliance is equipped with the 'Tablet
function that allows the use of the detergent
tablets.
These products are detergents with a combined cleaning and rinsing functions. They
can also contain other different agents depending on which kind of tablets you choose.
Once this function is selected it will remain
active for all following wash programmes.
With the selection of this function the inflow
of rinse aid is automatically deactivated and
also the indicator light for rinse aid is deactivated.
When using the 'Tablet function', the cycle
duration may change. If this is the case, the
running time for the programme is automatically updated on the digital display.
electrolux 13
Activate/deactivate the 'Tablet function'
before the start of a washing programme.
Once the programme is running, the set
of the 'Tablet function' can NO longer be
changed. You must cancel the set programme and then change the set of the
'Tablet function'.
Remember to set the washing programme again.
Activation/deactivation of the Tablet
function
Simultaneously press and hold the two Tablet buttons (function buttons D and E ) until
the Tablet indicator light comes on. This
means that the function is active.
To deactivate the function press the same
buttons again until the Tablet indicator light
goes off.
If the drying results are not satisfactory we suggest that you:
1. Fill up the rinse aid dispenser with
rinse aid.
2. Activate the rinse aid dispenser.
3. Set the rinse aid dosage to position
2.
• The activation/deactivation of the
rinse aid is only possible with the 'Tablet function' active.
Activation/deactivation of the rinse aid
dispenser
1. Press the On/Off button. The dishwasher
must be in setting mode.
2. Simultaneously press and hold function
buttons B and C , until the lights of function buttons A , B , and C start flashing.
3. Press function button B , the lights of
function buttons A and C go off while the
light of function button B continues to
flash. The digital display shows the current setting.
Rinse aid dispenser deactivated
Rinse aid dispenser activated
4. To change the setting, press button B
again, the digital display shows the new
setting.
5. To memorize the operation, switch off the
dishwasher by pressing the On/Off button.
If you decide to revert back to the
use of individual detergents we advise that you:
1. Deactivate the 'Tablet function'.
2. Fill up the rinse aid dispenser again.
3. Adjust the rinse aid dosage.
Select and start a washing programme
Select the washing programme and
delay start with the door slightly
opened. The start of the programme
or the countdown of the delay start
will occur only after the closure of
the door. Until then it is possible to
modify the settings
1. Check that the baskets have been loaded
correctly and that the spray arms are free
to rotate.
2. Check that the water tap is opened.
3. Press the On/Off button. The dishwasher
must be in setting mode.
4. Press the button corresponding to the required programme (refer to 'Washing
programmes' chart).
Close the dishwasher door, the programme starts automatically.
Setting and starting the programme with
delay start
1. After having selected the washing programme, press the delay start button until
the flashing number of hours for the delay
start shows in the digital display.
The start of the selected washing programme can be delayed for between 1
and 19 hours.
2. Close the dishwasher door, the countdown starts automatically.
3. The countdown will decrease with steps
of 1 hour.
4. The opening of the door will interrupt the
countdown. Close the door; the countdown will continue from the point at
which it was interrupted.
5. Once the delay start has elapsed the programme will start automatically.
14 electrolux
Warning! Interrupt or cancel a
washing programme in progress
ONLY if it's absolutely necessary.
Attention! Hot steam may escape
when the door is opened. Open the
door carefully.
Interrupt a washing programme in
progress
• Open the dishwasher door; the programme will stop. Close the door; the programme will start from the point at which
it was interrupted.
Cancel a delay start or a washing
programme in progress
• Simultaneously press and hold the two
function buttons B and C until all the programme lights come on.
• Cancelling a delay start will also cancel the
washing programme. You have to select
the washing programme again.
• If a new washing programme is to be selected, check that there is detergent in the
detergent dispenser.
End of the washing programme
• The dishwasher will automatically stop and
an audible signal informs you of the end of
the washing programme.
1. Open the dishwasher door.
– The digital display shows zero.
– End indicator light is on.
2. Switch of the dishwasher.
3. Leave the dishwasher door ajar for a few
minutes before removing the dishes; this
way they will be cooler and the drying will
be improved.
Unloading the dishwasher
• Hot dishes are sensitive to knocks. The
dishes should therefore be allowed to cool
down before removing from the appliance.
• Empty the lower basket first and then the
upper one; this will avoid water dripping
from the upper basket onto the dishes in
the lower one.
• Water may appear on the sides and the
door of the dishwasher as the stainless
steel will eventually become cooler than
the dishes.
When the washing programme has
finished, it is recommended that the
dishwasher is unplugged and the
water tap turned off.
electrolux 15
Washing programmes
Washing programmes
Programme
Anti+bac1)
Degree of soil
Quick
3)
ECO 4)
Programme description
Prewash
Main wash
Crockery, cutlery,
2 intermediate rinses
pots and pans
Final rinse
Drying
Heavy soil
Prewash
Main wash
Crockery, cutlery,
1 or 2 intermediate rinses
pots and pans
Final rinse
Drying
Any
Auto 2)
Type of load
Normal or light
soil
Crockery and
cutlery
Main wash
Final rinse
Normal soil
Crockery and
cutlery
Prewash
Main wash
Final rinse
Drying
Any.
Partial load (to be 1 cold rinse (to avoid food scraps from
completed later in sticking).
the day).
This programme does not require the use
of detergent.
Rinse
1) The 'Anti+bac' programme provides a sanitising final rinse.
2) During the 'Auto' washing programme the level of soiling on the dishes is determined by how cloudy
the water is. The programme duration, water and energy consumption levels can vary; this depends
upon whether the appliance is fully or partially loaded and if the dishes are lightly or heavily soiled. The
temperature of the water is automatically adjusted between 50° C and 65° C.
3) Ideal for washing a partially loaded dishwasher. This is the perfect daily programme, made to meet
the needs of a family of 4 persons who only wish to load breakfast and dinner crockery and cutlery.
4) The 'ECO' programme is recommended to wash a full 12 place setting load of normally soiled dishes.
It saves energy and water. Because it runs at a lower temperature, it is not suitable for heavily soiled
wash loads. To save energy, dry performance is reduced so you have to open the door at the end of
the wash cycle or even towel dry some dishes.
Consumption values
Programme
Programme duration
(in minutes)
1)
Energy consumption
(in kWh)
Water consumption
(in litres)
Anti+bac
-
1,9 - 2,1
23 - 25
Auto
-
1,1 - 1,8
12 - 25
Quick
-
0,9
9
-
0,8 - 0,88
11 - 12
-
0,1
4
ECO
2)
Rinse
1) The digital display shows the programme duration.
2) Test programme for test institutes
The consumption values are intended as
a guide and depend on the pressure and
the temperature of the water and also by
the variations of the power supply and
the amount of dishes.
16 electrolux
Care and cleaning
Cleaning the filters
The filters must be checked and cleaned
from time to time. Dirty filters will degrade the
washing result.
Warning! Before cleaning the filters
ensure that the machine is switched off.
1. Open the door, remove the lower basket.
2. The dishwasher filter system comprises a
coarse filter ( A ), a microfilter ( B ) and a
flat filter. Unlock the filter system using the
handle on the microfilter.
3. Turn the handle about 1/4 a turn anticlockwise and remove the filter system
7. Put the flat filter back in the base of the
washing compartment and ensure that it
fits perfectly.
8. Place the coarse filter ( A ) in the microfilter ( B ) and press together.
9. Put the filter combination in place and
lock by turning the handle clockwise to
the stop. During this process ensure that
the flat filter does not protrude above the
base of the washing compartment.
NEVER use the dishwasher without
filters. Incorrect repositioning and
fitting of the filters will produce poor
washing results and will result in
damage to the appliance.
NEVER try to remove the spray
arms.
If residues of soil have clogged the holes
in the spray arms, remove the debris
with a cocktail stick.
External cleaning
Clean the external surfaces of the machine
and control panel with a damp soft cloth. If
necessary use only neutral detergents. Never
use abrasive products, scouring pads or solvent (acetone, trichloroethylene etc...).
4. Take hold of the coarse filter ( A ) by the
handle with the hole and remove from the
microfilter ( B ).
5. Clean all filters thoroughly under running
water.
6. Remove the flat filter from the base of the
washing compartment and clean both
faces thoroughly.
Internal cleaning
Ensure that the seals around the door, the
detergent and rinse aid dispensers are
cleaned regularly with a damp cloth.
We recommend every 3 months you run the
wash programme for heavy soiled dishes using detergent but without dishes.
Prolonged periods of non-operation
If you are not using the machine for a prolonged period of time you are advised to:
electrolux 17
1. Unplug the appliance and then turn off
the water.
2. Leave the door ajar to prevent the formation of any unpleasant smells.
3. Leave the inside of the machine clean.
Frost precautions
Avoid placing the machine in a location
where the temperature is below 0°C. If this is
unavoidable, empty the machine, close the
appliance door, disconnect the water inlet
pipe and empty it.
Moving the machine
If you have to move the machine (moving
house etc...):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge
hoses.
4. Pull the machine out together with the
hoses.
Avoid over tilting the machine during transportation.
What to do if…
The appliance will not start or stops during
operation.
Certain problems can be due to the lack of
simple maintenance or oversights, which can
be solved with the help of the indications described in the chart, without calling out a
service technician.
Open the door and check which fault code
the digital display shows. Switch off the appliance and carry out the suggested corrective actions given in the following chart.
For fault codes not described in the chart,
please contact your Customer Care Centre.
With the appliance door closed an intermittent audible signal informs you that a
malfunction has occurred.
Fault codes and malfunction
Possible cause and solution
• continuous flashing of the running programme
light
• The digital display shows
The dishwasher does not fill with water
• The water tap is blocked or furred with limescale.
Clean the water tap.
• The water tap is turned off.
Turn the water tap on.
• The filter (where present) in the water inlet hose
is blocked.
Clean the filter.
• The water inlet hose has not been correctly laid
or it is kinked or squashed.
Check the water inlet hose connection.
• continuous flashing of the running programme
light
• The digital display shows
The dishwasher will not drain
• The sink spigot is blocked.
Clean out the sink spigot.
• The water drain hose has not been correctly laid
or it is kinked or squashed.
Check the water drain hose connection.
• continuous flashing of the running programme
light
• The digital display shows
appears in the
digital display
Anti-flood device is activated
• Close the water tap and contact your Customer
Care Centre.
18 electrolux
Malfunction
The programme does not start
Once these checks have been carried out
switch on the appliance and close the door.
The programme will continue from the point
at which it was interrupted.
If the malfunction or fault code reappears
contact your Customer Care Centre, quoting
the model (Mod.), product number (PNC)
and serial number (S.N.).
This information can be found on the rating
plate located on the side of the dishwasher
door.
Possible cause and solution
• The dishwasher door has not been properly
closed.
Close the door.
• The main plug is not plugged in.
Insert the main plug
• The fuse has blown out in the household fuse
box.
Replace the fuse.
• Delay start has been set.
If dishes are to be washed immediately, cancel
the delay start.
So that you always have these numbers at
hand, we recommend you to make a note of
them here:
Mod. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PNC : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S.N. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The wash results are not satisfactory
The dishes are not
clean
• The wrong washing programme has been selected.
• The dishes are arranged in such a way as to stop water reaching all parts
of the surface. The baskets must not be overloaded.
• The spray arms do not rotate freely due to incorrect arrangement of the
load.
• The filters in the base of the washing compartment are dirty or incorrectly
positioned.
• Too little or no detergent has been used.
• The drain hose connection is not correct.
The dishes are wet
and dull
• Rinse aid was not used.
• The rinse aid dispenser is empty.
There are streaks,
• Decrease rinse aid dosage.
milky spots or a bluish coating on
glasses and dishes
Water drops have
dried onto glasses
and dishes
• Increase rinse aid dosage.
• The detergent may be the cause. Contact the detergent manufacturer consumer care line.
If after all these checks, the problem persists,
contact your Customer Care Centre.
electrolux 19
Technical data
Dimensions
Width
59,6 cm
Height
82 - 88 cm
Depth
58 cm
Electrical connection - Voltage Overall power - Fuse
Information on the electrical connection is given on the rating plate
on the inner edge of the dishwasher door.
Water supply pressure
Minimum
Capacity
50 kPa (7 psi)
Maximum cold water
800 kPa (116 psi)
Maximum hot water
350 kPa (51 psi)
Place settings
12
Hints for test institutes
Testing in accordance with AS/NZS 2007
must be carried out with appliance fully loaded and using the test programme ( refer to
'Washing programmes' - 'Consumption values' ).
The rinse aid dispenser must be filled and the
door must be opened at the end of cycle for
30 minutes for drying assessment.
Full load: 12 standard place settings
Amount of detergent required:
10 g + 20 g ( AS/NZS )
Rinse aid setting
position 4 ( AS/NZS )
Arrangement upper basket
Arrangement lower basket
20 electrolux
Arrangement cutlery basket
3
4
5
3
4
5
3
4
5
3
4
5
3
4
5
3
4
5
3
4
5
3
4
5
3
4
5
3
4
5
3
4
5
3
4
5
2
2
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
Installation
Warning! ANY ELECTRICAL AND/OR
PLUMBING WORK REQUIRED TO
INSTALL THIS APPLIANCE MUST BE
CARRIED OUT BY A QUALIFIED
ELECTRICIAN AND/OR PLUMBER OR
COMPETENT PERSON.
Remove all packaging before positioning the
appliance.
If possible, position the appliance next to a
water tap and a drain.
During all operations that involve accessibility
to internal components the appliance must
be unplugged.
When inserting the appliance, ensure that the
water inlet hose, the drain hose and the
mains cable are not kinked or squashed.
electrolux 21
Building-in
This appliance must be fitted under a kitchen
counter or work surface.
The dimensions of the recess must be the
same as shown in the figure.
Adjusting the height of the appliance
It is important that the appliance absolutely
stands level so that the door closes and seals
properly.
If the appliance is not perfectly level the door
will catch on the levelling spacers on the right
and left side of the cabinet.
Turn the adjustable feet to the left or the right
until the appliance stands level.
To adjust the height proceed as follows:
1. Remove the adjustable plinth.
2. Adjust the height of the 2 front feet.
3. Adjust the rear foot by turning the screw
in the middle of the front kick plate to the
left or to the right.
4. Replace the adjustable plinth.
Fix to the adjacent units
No further openings for the venting of the appliance are required, but only to let the water
inlet hose, the drain hose and the mains cable pass through.
The appliance is fitted with adjustable feet
(max. 60 mm) so the height of the recess can
vary between 820 mm and 880 mm from the
floor.
Leave a space of 2 mm between the top of
the appliance and the underside of the kitchen counter.
Steam protection
Fit the steam protection onto the front part of
the work top using the screws provided.
Warning! THE APPLIANCE MUST BE
SECURED UNDER THE WORK TOP OR
TO THE ADJACENT UNITS USING THE
SUPPLIED BRACKETS.
FAILURE TO DO THIS WILL CAUSE INJURY OR DAMAGE.
1. Locate the supplied angular brackets in
the slots on the top of the appliance.
2. Adjust the height of the appliance.
3. Secure the appliance in position (upwards or sideways) by using the supplied
screws. Make sure the screws are tightened.
Caution! Do not secure the brackets
upwards if the top of the appliance is not
within 2 mm of the underside of the work
top.
Caution! Never drill holes through the
sides of the appliance. This will cause
damage to the hydraulic components.
22 electrolux
Adjustment of the plinth
Space at the bottom of the appliance can be
covered by lowering the plinth.
Water connection
Water inlet connection
This dishwasher may be fed with either hot
(max. 60°) or cold water. However a hot water supply is not always efficient with heavily
soiled crockery as it shortens the washing
programmes a lot. Therefore we recommend
connection to a cold water supply.
The water coupling nut fitted to the appliance
water inlet hose is designed to screw onto a
3/4" BSP thread spout.
The water pressure must be within the limits
given in the 'Technical data'. Your local Water Authority will advise you on the average
mains pressure in your area.
A water temperature tempering-valve must
be installed when the dishwasher is likely to
be connected to a solar hot water system,
drip heater, or any other supply where temperatures in excess of 60° are anticipated.
A pressure reducing valve must be fitted if the
hot water supply pressure exceeds 350 kPa
or the cold water supply pressure exceeds
800 kPa.
The water inlet hose must not be kinked,
crushed, or entangled when it is being connected.
The dishwasher features inlet and drain hoses which can be turned either to the left or
the right to suit the installation by means of
the locknut. The locknut must be correctly fitted to avoid water leaks.
Always use a new hose-set when connecting the appliance to the water
mains. An old hose-set must not be
reused. The water inlet hose should be
inspected every 12 months for deterioration and replaced if necessary.
This appliance has been fitted with safety features which will prevent the water
used in the appliance from returning
back into the drinking water system. This
appliance complies with the applicable
plumbing regulations.
Water inlet hose with safety valve
After connecting the double-walled water inlet hose, the safety valve is next to the tap.
Therefore the water inlet hose is only under
pressure while the water is running. If the water inlet hose starts to leak during this operation, the safety valve cuts off the running
water.
Please take care when installing the water
inlet hose:
• The electrical cable for the safety valve is
in the double-walled water inlet hose. Do
not immerse the water inlet hose or the
safety valve in water.
• If water inlet hose or the safety valve is
damaged, remove the mains plug immediately.
electrolux 23
• A water inlet hose with safety valve must
only be replaced by the Customer Care
Centre.
Warning! Dangerous voltage
Water drain connection
– Connect the water drain hose to the sink.
Secure it with the supplied hose clamp.
– Required height: 30 to 100 cm above bottom of the dishwasher.
– If you use a drain hose extension the total
length must be no longer than 4 metres.
Likewise the internal diameter of the couplings used for connections to the waste
outlet must be no smaller than the diameter of the hose provided. Ensure the drain
hose is not bent or squashed as this could
prevent or slow down the discharge of water.
When connecting the drain hose to an under
sink trap spigot, the entire plastic membrane must be removed. Failure to remove
all the membrane will result in food particles
building up over time eventually blocking the
appliance drain hose spigot
Our appliances are supplied with a security device to protect against the return of dirty water back into the machine.
If the spigot of your sink has a 'no return
valve' incorporated this can prevent the
correct draining of your dishwasher. We
therefore advise you to remove it.
To avoid water leakage after installation
make sure that the water couplings are
tight.
Electrical connection
Warning! Safety standards require
the appliance to be earthed.
Prior to using the appliance for the
first time, ensure that the rated voltage and type of supply on the rating
plate match that of the supply where
the appliance is to be installed. The
electrical rating data is also to be
found on the rating plate.
Always plug the mains plug into a
correctly installed shockproof socket.
Multi-way plugs, connectors and extension cables must not be used.
This could constitute a fire hazard
through overheating.
If necessary, have the domestic wiring system socket replaced. In case
that the mains cable has to be replaced, contact your Customer Care
Centre.
The plug must be accessible after
the appliance has been installed.
24 electrolux
Never unplug the appliance by pulling on the cable. Always pull the
plug.
The manufacturer accepts no liability for failure to observe the above
safety precautions.
Environment concerns
Packaging material
The packaging materials are environmentally
friendly and can be recycled. The plastic
components are identified by markings, e.g.
>PE<, >PS<, etc. Please dispose of the
packaging materials in the appropriate container at the community waste disposal facilities.
Warning! When a unit is no longer being
used:
• Pull the plug out of the socket.
• Cut off the cable and plug and dispose
of them.
• Dispose of the door catch. This prevents children from trapping themselves inside and endangering their
lives.
Old appliance
This appliance must be handed over to the
applicable collection point for recycling.
Ensure that this product is disposed of correctly. You will help prevent potential negative consequences for the environment and
human health, which could otherwise be
caused by inappropriate waste handling of
this product.
For more detailed information about recycling of this product, please contact your local city office, your household waste disposal
service or the shop where you purchased the
product.
electrolux 25
Warranty
FOR SALES IN AUSTRALIA AND NEW ZEALAND
This document sets out the terms and
conditions of product warranties for
Electrolux branded appliances. It is an
important document. Please keep it with
your proof of purchase documents in a
safe place for future reference should
you require service for your Electrolux
appliance. General Terms and Conditions
1. In this warranty
– Electrolux' means Electrolux Home
Products Pty Ltd ABN 51 004 762 341
in respect of Appliances purchased in
Australia and Electrolux (NZ) Limited in
respect of Appliances purchased in
New Zealand;
– 'Appliance' means any Electrolux
product purchased by you accompanied by this document;
– 'Warranty Period' means
i) where you use the Appliance for personal, domestic or household purposes in Australia the period of 24
months and in New Zealand the period of 24 months;
ii) where you use the Appliance for
commercial purposes, in Australia the
period of 3 months and in New Zealand the period of 3 months, (if the period stated is 0 months you are not
covered by this product warranty) following the date of original purchase of
the Appliance;
– 'you' means the purchaser of the Appliance not having purchased the appliance for re-sale, and 'your' has a
corresponding meaning.
2. This warranty only applies to Appliances
purchased and used in Australia or New
Zealand and is in addition to (and does
not exclude, restrict, or modify in any
way) any non-excludable statutory warranties in Australia or New Zealand.
3. Electrolux warrants that, when dispatched from an Electrolux warehouse, the
Appliance is free from defects in materials and workmanship for the Warranty
Period.
4. During the Warranty Period Electrolux or
its Authorised Service Centre will, at no
5.
6.
7.
8.
extra charge if your appliance is readily
accessible without special equipment,
and subject to these terms and conditions, repair or replace any parts which it
considers to be defective. You agree that
any replaced Appliances or parts become the property of Electrolux. This
warranty does not apply to light globes,
batteries, filters or similar perishable
parts.
Parts and Appliances not supplied by
Electrolux are not covered by this warranty.
Where you are within an Electrolux service area, this warranty covers the cost of
transport of the Appliance to and from
Authorised Service Centres of Electrolux
and travelling costs for representatives of
the Authorised Service Centre to and
from your home or business. If you are
outside an Electrolux service area, you
will bear these costs. For information
about whether you are within an Electrolux service area, please phone 13 13 49
in Australia, or 0800 10 66 10 in New
Zealand.
Proof of purchase is required before you
can make a claim under this warranty.
You may not make a claim under this
warranty unless the defect claimed is
due to faulty or defective parts or workmanship. Electrolux is not liable in the
following situations (which are not exhaustive):
– The Appliance is damaged by
i) accident
ii) misuse or abuse, including failure to
properly maintain or service
iii) normal wear and tear
iv) power surges, electrical storm
damage or incorrect power supply
v) incomplete or improper installation
vi) incorrect, improper or inappropriate
operation
vii) insect or vermin infestation.
– The Appliance is modified without authority from Electrolux in writing.
– The Appliance's serial number or warranty seal has been removed or defaced.
26 electrolux
– The Appliance was serviced or repaired by anyone other than Electrolux
or its Authorised Service Centres.
9. This warranty, the contract to which it
relates and the relationship between you
and Electrolux are governed by the law
applicable in the Australian State where
the Appliance was purchased or the law
applicable in New Zealand if the Appliance was purchased in New Zealand.
Where the Appliance was purchased in
New Zealand for business purposes the
Consumer Guarantee Act does not apply.
Limitation of Liability
10. To the extent permitted by law:
– Electrolux excludes all warranties other than as contained in this document;
– Electrolux shall not be liable for any
loss or damage whether direct or indirect or consequential arising from
your purchase, use or non-use of the
Appliance.
11. Provisions of the Trade Practices Act
and State consumer legislation in Australia, and the Consumer Guarantees
Act, the Sale of Goods Act and the Fair
Trading Act in New Zealand, imply warranties or conditions, or impose obligations, upon Electrolux which cannot be
excluded, restricted or modified. To the
extent permitted by law, the liability of
Electrolux (if any) arising out of or in re-
lation to the Appliance or any services
supplied by Electrolux shall be limited
(where it is fair and reasonable to do so),:
– in the case of Appliances, at its option,
to the replacement or repair of the Appliances or the supply of equivalent
products or the payment of the cost of
replacing the Appliances or having the
Appliances repaired or of acquiring
equivalent Appliances. Upon being replaced, parts and Appliances become
the property of Electrolux; or
– in the case of services, at its option, to
the supply of the services again or the
payment of the cost of having the
services re-supplied;
and in the case of Appliances or services
supplied in New Zealand, loss or damage whether direct or indirect or consequential that is reasonably foreseeable.
Privacy
You acknowledge that in the event that you
make a warranty claim it will be necessary for
Electrolux and its Authorised Service Centres
to exchange information in relation to you to
enable Electrolux to meet its obligations under this warranty.
Important Notice
Before Calling a Service Technician please
check carefully the operating instructions,
service booklet and the warranty terms and
conditions.
FOR SERVICE
SERVICE AUSTRALIA
OR TO FIND THE ADDRESS OF ELECTROLUX HOME PRODYOUR NEAREST STATE SERV- UCTS
ICE CENTRE IN AUSTRALIA
Please call 13 13 4 9
For the cost of a local call (Australia only)
FOR SPARE PARTS
OR TO FIND THE ADDRESS OF
YOUR NEAREST STATE
SPARE PARTS CENTRE IN
AUSTRALIA
Please call 13 13 50
For the cost of a local call (Australia only)
FOR SERVICE
SERVICE NEW ZEALAND
OR TO FIND THE ADDRESS OF ELECTROLUX HOME PRODYOUR NEAREST AUTHORISED UCTS
SERVICE CENTRE IN NEW
ZEALAND
Free call 0800 10 66 10
FOR SPARE PARTS
OR TO FIND THE ADDRESS OF
YOUR NEAREST SPARE
PARTS CENTRE IN NEW ZEALAND
Free call 0800 10 66 20
electrolux 27
www.electrolux.com
www.electrolux.com.au
117968331 - 01 - 112008