Sharp UX-144 Service manual

UX-P115U
SERVICE MANUAL
No. 00ZUXP115USME
FACSIMILE
MODEL
UX-P115
MODEL
UX-P115
SELECTION CODE DESTINATION
U
U.S.A.
CONTENTS
CHAPTER 1. GENERAL DESCRIPTION
[1] Specifications ................................................. 1-1
[2] Operation panel.............................................. 1-2
[3] Transmittable documents ............................... 1-3
[4] Installation ...................................................... 1-4
[5] Quick setup guide .......................................... 1-8
[6] Quick reference guide .................................... 1-9
[7] Option imaging film specifications.................. 1-9
CHAPTER 2. ADJUSTMENTS
[1] Adjustments ................................................... 2-1
[2] Diagnostics and service soft switch ............... 2-2
[3] Troubleshooting ........................................... 2-20
[4] Error code table............................................ 2-21
CHAPTER 3. MECHANISM BLOCKS
[1] General description ........................................ 3-1
[2] Disassembly and assembly procedures......... 3-3
CHAPTER 4. DIADRAMS
[1] Block diagram ................................................ 4-1
[2] Wiring diagram ............................................... 4-2
[3] Point-to-point diagram.................................... 4-3
CHAPTER 5. CIRCUIT DESCRIPTION
[1] Circuit description ..........................................5-1
[2] Circuit description of control PWB ................5-2
[3] Circuit description of TEL/LIU PWB...............5-9
[4] Circuit description of power supply PWB......5-12
[5] Circuit description of CIS unit ......................5-12
CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS
LAYOUT
[1] Control PWB circuit .......................................6-1
[2] TEL/LIU PWB circuit......................................6-9
[3] Power supply PWB circuit ...........................6-12
[4] Operation Panel PWB circuit .......................6-14
CHAPTER 7. OPERATION FLOWCHART
[1] Protocol .........................................................7-1
[2] Power on sequence.......................................7-2
CHAPTER 8. OTHER
[1] Service tools ..................................................8-1
[2] Changing the record paper size ....................8-4
Parts Guide
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for
maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
UX-P115U
CAUTION FOR BATTERY REPLACEMENT
(French)
ATTENTION
Il y a danger d'explosion s' il y a remplacement incorrect
de la batterie. Remplacer uniquement avec une batterie du
même type ou d'un type recommandé par le constructeur.
Mettre au rébut les batteries usagées conformément aux
instructions du fabricant.
(Swedish)
VARNING
Explosionsfare vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
(German)
Achtung
Explosionsgefahr bei Verwendung inkorrekter Batterien.
Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ oder
vom Hersteller empfohlene Batterien verwendet werden.
Entsorgung der gebrauchten Batterien nur nach den vom
Hersteller angegebenen Anweisungen.
(Danish)
ADVARSEL !
Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandoren.
(English)
Caution !
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the equipment manufacturer.
Discard used batteries according to manufacturer's instructions.
(Finnish)
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.
PRECAUTIONS FOR USING LEAD-FREE SOLDER
1. Employing lead-free solder
The TEL/LIU PWB and Operation Panel PWB of this model employs lead-free solder.
This is indicated by the "LF" symbol printed on the PWB and in the service manual.
The suffix letter indicates the alloy type of the solder.
Example:
Indicates lead-free solder of tin, silver and copper.
2. Using lead-free solder
When repairing a PWB with the "LF" symbol, only lead-free solder should be used. (Using normal tin/lead alloy solder may
result in cold soldered joints and damage to printed patterns.)
As the melting point of lead-free solder is approximately 40°C higher than tin/lead alloy solder, it is recommended that a
dedicated bit is used, and that the iron temperature is adjusted accordingly.
3. Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is higher and has poorer melting point (flow), to prevent damage to the
land of the PWB, extreme care should be taken not to leave the bit in contact with the PWB for an extended period of time.
Remove the bit as soon as a good flow is achieved.
The high content of tin in lead free solder will cause premature corrosion of the bit.
To reduce wear on the bit, reduce the temperature or turn off the iron when it is not required.
Leaving different types of solder on the bit will cause contamination of the different alloys, which will alter their
characteristics, making good soldering more difficult.
It will be necessary to clean and replace bits more often when using lead-free solder. To reduce bit wear, care should be
taken to clean the bit thoroughly after each use.
–i–
UX-P115U
UX-P115U
FAX
Service
E
Market
Manual 1. GENERAL DESCRIPTION
CHAPTER
[1] Specifications
Automatic dialing:
Imaging film:
Memory size*:
Modem speed:
Transmission time*:
Resolution:
Automatic document
feeder:
Recording system:
Halftone (grayscale):
Compression scheme:
Display:
Applicable telephone line:
Paper tray capacity:
Compatibility:
Input document size:
30 numbers
Initial starter roll:
(included with machine): 32 ft.(10 m)
(approx. 30 letter-size pages)
Replacement roll (not included):
UX-5CR 164 ft.(50 m) (one roll yields
approx. 150 letter-size pages)
448 KB (approx. 24 average pages)
9,600 bps with automatic fallback to
lower speed
Approx. 15 seconds
Horizontal: 203 pixels/inch (8 dots/mm)
Vertical:
Standard: 98 lines/inch (3.85 lines/mm)
Fine/Halftone: 196 lines/inch
(7.7 lines/mm)
Super fine: 391 lines/inch
(15.4 lines/mm)
10 pages max. (letter/A4, 20-lb. paper)
Effective scanning width:
Effective printing width:
Contrast control:
Reception modes:
Copy function:
Telephone function:
Power requirements:
Operating temperature:
Humidity:
Power consumption:
Dimensions (without
attachments):
Thermal transfer recording
64 levels
MR, MH, Sharp(H2)
16-digit LCD display
Public switched telephone network
Letter: Approx. 50 sheets (20-lb. copier
paper at room temperature; maximum
stack height should not be higher than
the line on the tray)
Legal: 5 sheets
Recommended paper weight is 20-lb.
Copy Bond
Weight (without attachments):
ITU-T (CCITT) G3 mode
Automatic feeding:
Width: 5.8 to 8.5” (148 to 216 mm)
Length: 5.5 to 11” (140 to 279 mm)
Manual feeding:
Width: 5.8 to 8.5” (148 to 216 mm)
Length: 5.5 to 23.6” (140 to 600 mm)
8.3” (210 mm) max.
8.3” (210 mm) max.
Automatic/Dark selectable
TEL/FAX
Single / Multi (99 copies/page)
Yes
(cannot be used if power fails)
120 V AC, 60 Hz
41 - 95°F (5 - 35°C)
25 - 85 % RH
Stand-by: 3.6 W
Maximum: 100 W
Width: 12.9” (327 mm)
Depth: 7.6” (193 mm)
Height: 6.4” (163 mm)
Approx. 6.2 lbs (2.8 kg)
*Based on Sharp Standard Chart at standard resolution in Sharp special mode, excluding time for protocol signals (i.e., ITU-T phase C
time only).
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement
without prior notice. The performance specifications figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
1–1
UX-P115U
[2] Operation panel
1
6
RESOLUTION/
RECEPTION MODE
SPEAKER
7
8
ABC
TEL FAX
1
GHI
STOP
FLASH
COPY/HELP
START/MEMORY
10 11
3 4 5
2
PQRS
HOLD
SPEED
Z
REDIAL
12 13
A
14
DEF
2
JKL
4
POLL
9
5
TUV
7
FUNCTION
3
MNO
6
WXYZ
8
9
0
15
1. SPEAKER key
8. Number keys
Press this key to listen to the line and fax tones through the speaker
when faxing a document.
Use these keys to dial numbers, and enter numbers and letters when
storing auto-dial numbers.
Note: This is not a speakerphone. You must pick up the handset to
talk with the other party.
9. Panel release
Press this release to open the operation panel.
2. RESOLUTION / RECEPTION MODE key
10. STOP key
When a document is in the feeder, press this key to adjust the resolution for faxing or copying. At any other time, press this key to select the
reception mode (an arrow in the display will point to the currently
selected reception mode).
Press this key to cancel operations before they are completed.
11. COPY/HELP key
When a document is in the feeder, press this key to make a copy of a
document. At any other time, press this key to print out the Help List, a
quick reference guide to the operation of your fax machine.
3. FLASH key
This key is used for Call Waiting and other special services that
require subscription from your phone company. Your phone company
will provide you with details on how to use the key.
12. START/MEMORY key
Press this key after dialing to begin fax transmission. Press this key
before dialing to send a fax through memory.
4. POLL key
Press this key after dialing another fax machine to receive a document
(previously loaded in the other machine's feeder) without assistance
from the operator of the other machine.
13. SPEED key
Press this key to dial a fax or voice number using an abbreviated 2digit Speed Dial number.
5. HOLD key
Press this key to put the other party on hold during a phone conversation.
14. Left and right arrow keys
Auto-dial numbers: When sending a fax or making a phone call,
press these keys to scroll through your auto-dial numbers, the
"REVIEW CALLS" list (only available if you have Caller ID), and the
last number dialed (redial).
FUNCTION key settings: Press the right arrow key after scrolling with
the up and down arrow keys to select a FUNCTION key setting.
6. Display
This displays messages and prompts to help you operate the machine.
7. UP and DOWN arrow keys
Enlarge/Reduce setting: When marking a copy of a document, press
these keys to select an enlarge/reduce setting.
Volume setting: When a document is not in the feeder, press these
keys to change the handset volume when the handset is lifted, the
speaker volume when the SPEAKER key has been pressed, or the
ringer volume at any other time.
FUNCTION key setting: Press these keys after pressing the FUNCTION key to scroll through the FUNCTION MODE settings.
15. FUNCTION key
Press this key to followed by the arrow keys select special functions
and setting.
1–2
UX-P115U
[3] Transmittable documents
5. Automatic Document Feeder Capacity
1. Document Sizes
Number of pages that can be placed into the feeder at anytime is as
follows:
Normal size
width
length
Normal size: max. ADF 10 pages
5.8 to 8.5” (148 - 216 mm)
5.5 to 11” (140 - 279 mm)
Special size: single sheet only (manual feed)
NOTE: • When you need to send or copy more pages than the feeder
limit, place additional pages in feeder when last page in feeder
is being scanned.
• Place additional pages carefully and gently in feeder.
If force is used, double-feeding or a document jam may result.
(Max.)
(Max.)
Letter
size
(Min.)
140mm
148mm
6. Readable Width & Length
600mm
The readable width and length of a document are slightly smaller than
the actual document size.
279mm
216mm
[Normal size]
Note that characters or graphics outside the effective document scanning range will not be read.
216mm
[Special size]
•
Readable width
8.3” (210mm), max
Use document carrier sheet for smaller documents.
•
With special sizes, only one sheet can be fed into the machine at a
time. Insert next page into feeder as current page is being scanned.
2. Paper Thickness & Weight
Paper weight
Paper thickness (ref.)
Paper size
Feeder capacity
10 sheets
1 sheet (Manual)
70 kg
70 kg ~ 135 kg
80 g/m2
52 g/m2 ~ 157g/m2
0.1 mm
0.1 mm ~ 0.18mm
LGL (216 mm x 355.6 mm)
A4 (210 mm x 297 mm)
LTR (216 mm x 279 mm)
A4/LTR: 10 sheets
LGL : 1 sheet
Readable width
•
Readable length
This is the length of the document sent minus 0.2” (5mm) from the
top and bottom edges.
0.2" (5mm)
3. Document Types
•
Normal paper
Readable length
Documents handwritten in pencil (No. 2 lead or softer), fountain
pen, ball-point pen, or felt-tipped pen can be transmitted.
0.2" (5mm)
Documents of normal contrast duplicated by a copying machine
can also be transmitted.
•
Diazo copy (blue print)
•
Diazo copy documents of a normal contrast may be transmitted.
•
Carbon copy
A carbon copy may be transmitted if its contrast is normal.
4. Cautions on Transmitting Documents
•
Documents written in yellow, greenish yellow, or light blue ink cannot be transmitted.
•
Ink, glue, and correcting fluid on documents must be dry before the
documents can be transmitted.
•
All clips, staples and pins must be removed from documents before
transmission.
•
Patched (taped) documents should be copied first on a copier and
then the copies used for transmission.
•
All documents should be fanned before insertion into the feeder to
prevent possible double feeds.
1–3
UX-P115U
[4] Installation
1) Remove the paper from the paper tray and open the operation
panel (press
1
).
1. Site selection
Take the following points into consideration when selecting a site for
this model.
ENVIRONMENT
•
The machine must be installed on a level surface.
•
Keep the machine away from air conditioners, heaters, direct sunlight, and dust.
•
Provide easy access to the front, back, and sides of the machine.
In particular, keep the area in front of the machine clear, or the original document may jam as it comes out after scanning.
•
The temperature should be between 41 - 95°F (5 - 35°C).
•
The humidity should be between 25% and 85% (without condensation).
2
1
If you are loading the imaging film for the first
time, go to Step 4.
ELECTRICITY
AC 120V, 60Hz, grounded (3-prong) AC outlet is required.
2) Remove the used film and empty spool.
Caution!
•
Connection to a power source other than that specified will cause
damage to the equipment and is not covered under the warranty.
•
If your area experiences a high incidence of lightning or power
surges, we recommend that you install a surge protector for the
power and telephone lines. Surge protectors can be purchased at
most telephone specialty stores.
If the machine is moved from a cold to a warm place...
Condensation may form on the reading glass if machine is moved from
a cold to a warm place, this will prevent proper scanning of documents
for transmission. Turn on the power and wait approximately 2 hours
before using machine.
3) Remove the two green gears from the spools.
DO NOT DISCARD THE TWO GREEN GEARS!
TELEPHONE JACK
A standard RJ11C single-line wall telephone jack must be located near
the machine. This is the telephone jack commonly used in most
homes and offices.
•
Plugging the fax machine into a jack which is not RJ11C single-line
wall telephone jack may result in damage to the machine or your
telephone system. If you do not know what kind of jack you have, or
need to have one installed, contact the telephone company.
4) Remove the new roll of imaging film from its packaging.
•
Cut the band that holds rolls together.
5) Insert the green gears.
Make sure the gears fit into the slots in the ends of the rolls.
2. Loading the imaging film
Your fax uses a roll of imaging film to create printed text and images.
The print head in the fax applies heat to the imaging film to transfer ink
to the paper. Follow the steps below to load or replace the film.
•
The initial starter roll of imaging film included with your fax can print
about 30 letter-size pages
•
When replacing the film, use a roll of Sharp UX-5CR imaging film.
One roll can print about 150 letter-size pages.
1 slot
2 slots
Use only Sharp Genuine
Supplies with this logo:
1–4
UX-P115U
2) Plug the power cord into a 120 V, 60 Hz, grounded AC (3-prong)
outlet.
6) Insert the film into the print compartment.
Fit ends of rolls
onto hubs
Caution!
Do not plug the power cord into any other kind of outlet. This will
damage the machine and is not covered under the warranty.
•
The machine does not have a power on/off switch, so the power
is turned on and off by simply plugging in or unplugging the
power cord.
Thick roll
to rear
7) Rotate the front gear as shown until the film is taut.
3) Insert one end of the line cord into the jack on the back of the
machine marked TEL. LINE. Insert the other end into a standard
(RJ11C) single-line wall telephone jack.
TE
LINL.
E
8) Close the operation panel (press down on both sides to make sure
it clicks into place).
Setting the dial mode: The fax machine is set for tone dialing. If you
are on a pulse dial line, you must set the fax machine for pulse dialing. Press the keys on the operation panel as follows:
Display:
1. Press
•
Make sure the handset cord goes into the jack marked with a
handset symbol on the side of the machine.
•
Use the handset to make ordinary phone calls, or to transmit
and receive faxes manually.
2. Press
once and
3. Press
once.
5. Press
1) Connect the handset as shown and place it on the handset rest.
The ends of the handset cord are identical, so they will go into
either jack.
once and
4. Select the dial mode:
TONE: 1 PULSE: 2
3. Connections
•
FUNCTION
STOP
once.
twice.
OPTION SETTING
DIAL MODE
1=TONE, 2=PULSE
The display briefly shows
your selection, then:
DISTINCTIVE
to exit.
4) Attach the paper tray and paper tray extension.
Note: The paper tray extension has a top side and a bottom side. If
you cannot insert the tabs into the holes, turn the support over.
Attach the paper tray.
Attach the paper tray extension.
Click!
Insert
horizontally
and rotate up.
1–5
UX-P115U
4. Loading printing paper
3) Setting the paper size.
The fax has been set at the factory to scale received faxes to letter
size paper. If you loaded legal paper, you must change the paper
size setting to LEGAL.
You can load letter or legal size paper in the paper tray. Recommended paper weight is 20-lb. Copy Bond. The maximum number of
sheets is as follows:
Letter size: Approx. 50 sheets (20-lb. copier paper at room temperature; maximum stack height should not be higher than the line on the
tray)
Display:
1. Press
Legal size: 5 sheets
1) Fan the paper, and then tap the edge against a flat surface to even
the stack. Make sure the stack edges are even.
FUNCTION
once and
2. Press
once and
3. Press
once.
once.
twice.
5. Press
PAPER SIZE SET
1=LETTER, 2=LEGAL
The display briefly shows
your selection, then:
4. Select the paper size:
LETTER: 1 LEGAL:
STOP
OPTION SETTING
2
COPY CUT-OFF
to return to the date and time display.
4) Print contrast setting.
You fax has been set at the factory to print at normal contrast. If
desired, you can change the print contrast setting to LIGHT.
2) Insert the stack of paper into the tray, PRINT SIDE DOWN.
•
If paper remains in the tray, take it out and combine it into a single stack with the new paper.
•
Be sure to load the paper so that printing takes place on the
print side of the paper. Printing on the reverse side may result
in poor print quality.
•
GENTLY LOAD PAPER INTO THE PAPER TRAY.
•
DO NOT FORCE IT DOWN INTO THE FEED SLOT.
Display:
1. Press
FUNCTION
once and
2. Press
once and
3. Press
once.
once.
3 times.
4. Select the print contrast:
NORMAL: 1 LIGHT: 2
5. Press
The stack
should not
be higher
than this line.
Note: Do not use paper that has already been printed on, or
paper that is curled.
When you are finished, press
START/MEMORY
ADD PAPER &
↑
PRESS START KEY
↑
Note: If at any time the display shows
the alternating messages at right, check
the printing paper. If the tray is empty,
add paper. If these is paper in the tray,
take it out and then reinsert it.
.
1–6
STOP
OPTION SETTING
PRINT CONTRAST
1: NORMAL
The display briefly shows
your selection, then:
PAPER SIZE SET
to return to the date and time display.
UX-P115U
5. Clearing a jammed document
6. Clearing jammed printing paper
If the original document doesn’t feed properly during transmission or
copying, or DOCUMENT JAMMED appears in the display, first try
pressing the START/MEMORY key. If the document doesn’t feed out,
remove it as explained below.
1) Open the operation panel (press
1
)
Important:
Do not try to remove a jammed document without releasing it as
explained below. This may damage the feeder mechanism.
1) Press
1
and slowly open the operation panel until it is half open.
2
1
2
2) Gently pull the jammed paper out of the machine, making sure no
torn pieces of paper remain in the print compartment or rollers.
1
2) Flip up the green levers on each side of the white roller.
3) Rotate the front gear until the film is taut, and then close the operation panel (press down on both sides to make sure it clicks into
place).
3) Gently and remove the document.
•
Be careful not to tear the document.
4) Flip down the green levers on each side of the white roller. Rotate
the front gear until the film is taut, and then close the operation
panel (press down on both sides to make sure it clicks into place).
1–7
UX-P115U
[5] Quick setup guide
Note: To enter your name and fax number and set the date and time so that they
appear at the top of each fax you send, see page Chapter 1 of your operation manual.
1
2
Connect the handset
and place it on the
handset rest.
3
Plug the power cord
into a 120 V grounded
outlet.
4
Connect the telephone
line cord to the TEL.
LINE jack and a wall
telephone jack.
Attach the paper tray
and document support.
TE
L.L
INE
Click!
Note: If the
support does
not go in,
turn it over.
5
Load the imaging film.
1. Open the operation panel (press
1
).
3. Insert the green gears.
2. Remove the imaging film from its packaging.
Cut the band that holds the rolls together.
IMPORTANT: Do NOT discard the
green gears. They are not included
with replacement imaging film.
1 slot
2
Make sure
the gears fit
into the slots
in the ends of
the rolls.
1
4. Insert the film into the print compartment.
5. Rotate the front spool as shown
until the film is taut.
2 slots
6. Close the operation panel (press
down on both sides to make sure it
clicks into place).
Fit ends of
rolls onto hubs
6
Load paper.
7
The stack
should not be
higher than this
line
Insert the
paper print
side down.
Select the reception mode for incoming faxes and
voice calls:
FAX mode: The machine automatically answers all
calls and begins fax reception.
TEL mode: Lift the handset when the machine rings.
Press
START/MEMORY
to begin fax reception.
TEL FAX
JAN-01 10:30
• GENTLY LOAD PAPER INTO THE PAPER TRAY.
RESOLUTION/
RECEPTION MODE
• DO NOT FORCE IT DOWN INTO THE FEED SLOT.
Note: If you loaded legal paper, see of the operation manual to change the paper size
setting to LEGAL.
1–8
TEL FAX
JAN-01 10:30
The arrow points
to the selected
reception mode.
UX-P115U
[6] Quick reference guide
3. Storing Auto Dial Numbers
1. Sending Faxes
1. Press
Place your document (up to 10 pages) face down in the document
feeder.
2. Enter a 2-digit Speed Dial number (01 to 30).
FUNCTION
once and
once.
3. Enter the fax number and press
START/MEMORY
.
4. Enter a name by pressing number keys. (To enter two letters in
succession that require the same key, press
after entering
the first letter.)
G=
N=
A=
H=
O=
V=
B=
I =
P=
W=
C=
J=
Q=
X=
D=
K=
R=
Y=
E=
L=
S=
Z=
F=
M=
T=
SPACE =
U=
1.1. Normal Dialing
1. Lift the handset or press
SPEAKER
2. Dial the fax number.
START/MEMORY
SPEED
STOP
This article is composed of polyester film coated with heat-resistant
layer, matt layer and hot melt ink layer, leader film and paper core. Ink
film specification is "DNP standard ink film HC".
.
1
2
3
4
.
2. Enter the 2-digit Speed Dial number.
3. Press
START/MEMORY
.
1
1.3. Search Dialing
1. Press
or
2
3
until the name of the other party appears in
4
the display (if no name was stored, the number will appear).
2. Press
START/MEMORY
.
RESOLUTION/
RECEPTION MODE
Heat Resistant Layer
Base Film
Matt Layer
Hot melt Ink Layer
2. Details of compositions
2.1. Base film
2. Receiving Faxes
Press the
Heading
Material
until the arrow in the display points to the
desired reception mode.
JAN-01 10:30
Heading
Grade
TEL FAX
Heading
Grade
FAX mode: The fax machine automatically answers and receives the
incoming document.
Requirements
HR Mixer P-5
Measuring method
–
Requirements
ML Sumi
Measuring method
–
2.4. Hot melt ink layer
TEL mode: Answer all calls (even faxes) by picking up the handset. To
begin fax reception, press
Measuring method
–
2.3. Matt layer
JAN-01 10:30
START/MEMORY
Requirements
Polyethyleneterephthalate
2.2. Heat resistant layer
TEL FAX
RESOLUTION/
RECEPTION MODE
.
1. Structure
1.2. Speed Dialing
1. Press
and then
[7] Option imaging film specifications
3. Wait for the reception tone (if a person answers, ask them to press
their Start key).
4. Press
START/MEMORY
5. Press
.
.
Heading
Grade
1–9
Requirements
#507W
Measuring method
–
UX-P115U
UX-P115U
FAX
Service
E
Market
Manual 2. ADJUSTMENTS
CHAPTER
4. Settings
4.1. Dial mode selector
[1] Adjustments
DIAL mode (Soft Switch No. SW-B4 DATA No. 3)
1. General
(step 1) Select "OPTION SETTING".
Since the following adjustments and settings are provided for this
model, make adjustments and/or setup as necessary.
KEY :
2. Adjustments of output voltage (FACTORY ONLY)
(step 2) Select "DIAL MODE".
1. Install the power supply unit in the machine.
KEY:
FUNCTION
DISPLAY:
Push until DIAL MODE
indicated because the number of
's changes by the model.
2. Set the recording paper and document.
3. When the document is loaded, power is supplied to the output
lines. Confirm that outputs are within the limits below.
OPTION SETTING
DISPLAY:
DIAL MODE
NUMBER OF RING
is
1=TONE, 2=PULSE
(step 3) Select, using "1" or "2".
2.1. Output voltage settings
TEL/LIU PWB
POWER
SUPPLY
PWB
KEY:
1
DISPLAY:
TONE SELECTED
KEY:
2
DISPLAY:
PULSE SELECTED
(step 4) End, using the "STOP" key.
CNPS
6
1
CNLIUA
CNPW
CNLIUA
KEY:
STOP
CNTH
CNPRG
5. Volume adjustments
CNMT
CONTROL
PWB
CNCSW
CNSP
CNPN
You can adjust the volume of the speaker, handset, and ringer using
the UP and DOWN keys.
CNCIS
5.1. Speaker
Voltage limits
4.25V ~ 5.75V
23.3V ~ 24.7V
Connector
No.
Pin No.
1
2
3
4
5
6
1. Press the SPEAKER key.
CNPW
2. Press the UP or DOWN key until the display shows the desired volume level.
+24V
+24V
MG
MG
DG
Vreg(+5V)
Display:
SPEAKER: HIGH
↔
Output
Vreg(+5V)
+24V
• Press SPEAKER key again to
turn off the speaker.
↔
SPEAKER: MIDDLE
SPEAKER: LOW
3. IC protectors replacement
5.2. Handset
ICPs (IC Protectors) are installed to protect the motor driver circuit.
ICPs protect various ICs and electronic circuits from an overcurrent
condition.
1. When talking through the handset, press UP or DOWN key until the
display shows the desired volume level.
Display:
RECEIVER: HIGH
↔
The location of ICPs are shown below:
↔
RECEIVER: MIDDLE
CNPW
CNLIUA
• Note: The volume reverts to
MIDDLE each time you
replace the handset.
RECEIVER: LOW
5.3. Ringer
FU100
CONTROL PWB
(BOTTOM SIDE)
1. Press the UP or DOWN key. (Make sure SPEAKER key has not
been pressed, the handset is not lifted, and a document is not
loaded in the feeder.)
↔
Display:
RINGER: HIGH
↔
RINGER: MIDDLE
1) FU100 (KAB3202) is installed in order to protect IC's from an
overcurrent generated in the motor drive circuit. If FU100 is open,
replace it with a new one.
• The ringer will ring once at the
selected level, then the date
and time will reappear in the
display.
↔
RINGER: LOW
RINGER OFF: OK?
2. If you selected RINGER OFF: OK?, press START/ MEMORY key.
2–1
UX-P115U
[2] Diagnostics and service soft switch
1. Operating procedure
1.1. Entering the diagnostic mode
Press FUNC → 9 →
ROM Ver. TC89
→ 8 → # → 7 , and the following display will appear.
After 2 sec: DIAG MODE
TC89
Then press the START key. Select the desired item with the
key or the # key or select with the rapid key. Enter the mode with the START key.
(Diag· specifications)
FUNC
9
8
TC89
7
DIAG MODE
START
Soft switch mode
START
START
Entry data receive
ROM & RAM check
START
START
Entry data send
Aging mode
START
START
Auto feeder mode
Panel key test
START
START
All black mode
Check pattern
START
START
Shading mode
Signal send mode
START
START
Memory clear
If the diag mode cannot be set, repeat the diag mode operation, performing the following operation.
After the power is turned on and "WAIT A MOMENT" is indicated, press
the STOP key.
STOP
KEY
START
KEY
"Power ON" +
In relation with the process response (request from Production
Engineering) "WAITA MOMENT" clock indication may appear depending
on STOP key timing. If the STOP key is held down, "MEMORY CLEAR?"
appears.
Memory clear
(Work + Backup)
2. Diagnostic items
ITEM No.
Contents
Function
1
SOFT SWITCH MODE
Soft switches are displayed and changed. List can be output.
2
ROM & RAM CHECK
ROM is sum-checked, and RAM is matched. Result list is output.
3
AGING MODE
10 sheets of check patterns are output every 5 minutes per sheet.
4
PANEL KEY TEST
Panel keys are tested. Result list is output.
5
CHECK PATTERN
Check pattern is output.
6
SIGNAL SEND MODE
Various signals of FAX communication are output.
7
MEMORY CLEAR
Back-up memory is cleared, and is set at delivery.
8
SHADING MODE
Shading compensation is performed in this mode.
9
ALL BLACK PRINT
To check the print head, whole dots are printed over the interval of 2 m.
10
AUTO FEEDER MODE
Insertion and discharge of document are tested.
11
ENTRY DATA SEND
Registered content is sent.
12
ENTRY DATA RECEIVE
Registered content is received, and its list is output.
2–2
UX-P115U
3. Diagnostic items description
3.6. Signal send mode
This mode is used to send various signals to the circuit during FAX
communication. Every push of START key sends a signal in the following sequence. Moreover, the signal sound is also output to the speaker
when the line monitor of the soft switch is on.
3.1. Soft switch mode
Used to change the soft switch settings.
The soft switch which is stored internally is set by using the keys.
[1] No signals
The available soft switches are SW-A1 to SW-O6.
[2] 9600BPS (V.29)
The content of soft switches is shown in page 2-5 to 2-18.
[3] 7200BPS (V.29)
The contents are set to factory default settings.
[4] 4800BPS (V27ter)
3.2. ROM & RAM check
[5] 2400BPS (V27ter)
ROM executes the sum check, and RAM executes the matching test.
The result will be notified with the number of short sounds of the
buzzer as well as by printing the ROM & RAM check list.
[6] 300BPS (FLAG)
[7] 2100Hz (CED)
Number of short sounds of buzzer:
[8] 1100Hz (CNG)
0 → No error
3.7. Memory clear
1 → ROM error
2 → RAM error (4 Kbyte SRAM or 512 Kbyte DRAM)
This mode is used to clear the backup memory and reset to the default
settings.
3.3. Aging mode
3.8. Shading mode
If any document is present, copying will be executed sheet by sheet. If
no document is present, the check pattern will be printed sheet by
sheet. This operation will be executed at a rate of one sheet per 5 minutes, and will be ended at a total of 10 sheets.
The mode is used for the shading compensation. For reading, set up
the special original paper.
The compensation memorizes the reference data of white and black
for reading.
Moreover, the memorized data is not erased even if memory clear
mode is executed.
3.4. Panel key test
This mode is used to check whether each key operates properly.
Press the key on the operation panel, and the key will be displayed on
the display. Therefore, press all keys. At this time, finally press the
STOP key.
3.9. All black print
This mode is used to check the state of the printing head and to intentionally overheat it. Whole dots are printed over the interval of 2 m. If it
is overheated or the printing sheet is jammed, press STOP key for the
end.
When the STOP key is pressed, the keys which are not judged as
"pressed" will be printed on the result list.
•
3.10. Auto feeder mode
LED part of the contact image sensor (CIS) is kept on during the
term from when “START” of the panel test mode to end with the
STOP key.
In this mode, a document is inserted and discharged to check the auto
feed function.
3.5. Check pattern
After this mode is started, set a document, and the document feed will
be automatically tested.
This mode is used to check the state of the printing head. It is ended
with the following pattern printed on one printing sheet.
1
3.11. Entry data send
This mode is used to send the registered data to another machine and
make the other machine copy the registered content.
1 DOT
B B B B B B B B B B B B B B B B B B B BB B B B B B B B B B B B B B B B B B B BB
B B B B B B B B B B B B B B B B B B B BB B B B B B B B B B B B B B B B B B B BB
B B B B B B B B B B B B B B B B B B B BB B B B B B B B B B B B B B B B B B B BB
2
Before sending in this mode, it is necessary to set the other machine
at the entry data receive mode.
2 DOTS
B B B B B B B B B B B B B B B B B B B BB B B B B B B B B B B B B B B B B B B BB
B B B B B B B B B B B B B B B B B B B BB B B B B B B B B B B B B B B B B B B BB
B B B B B B B B B B B B B B B B B B B BB B B B B B B B B B B B B B B B B B B BB
3
4
The following, information will be sent to the remote machine:
3 DOTS
B B B B B B B B B B B B B B B B B B B BB B B B B B B B B B B B B B B B B B B BB
B B B B B B B B B B B B B B B B B B B BB B B B B B B B B B B B B B B B B B B BB
B B B B B B B B B B B B B B B B B B B BB B B B B B B B B B B B B B B B B B B BB
1. Telephone list data
4 DOTS
2. Sender register data
B B B B B B B B B B B B B B B B B B B BB B B B B B B B B B B B B B B B B B B BB
B B B B B B B B B B B B B B B B B B B BB B B B B B B B B B B B B B B B B B B BB
B B B B B B B B B B B B B B B B B B B BB B B B B B B B B B B B B B B B B B B BB
3. Optional setting content
4. Soft switch content
5. Junk fax number list
6. Recording setting list data
2–3
UX-P115U
3.12. Entry data receive
In this mode, the registered data sent from the other machine is received and the received data is registered in the machine. When this mode
is used for receiving, the other machine must be in the entry data send
mode.
After receiving is completed, the following lists are printed.
1.Telephone list data
2.Sender register data (*)
3.Optional setting list (*)
4.Soft switch content
5.Junk fax number list (*)
6.Recording setting list data (*)
(*): Refer to SETUP LIST
4. How to make soft switch setting
To enter the soft switch mode, press the following key entries in sequence.
Press FUNCTION
DATA No.
9
8
7
START
START
1 2 3 4 5 6 7 8
S F T SW-A1 = 0 0 0 0 0 0 0 0
Press FUNCTION key.
S F T SW-A1 = 1 0 0 0 0 0 0 0
Press
key.
Press
key.
S F T SW-A1 = 1 0 0 0 0 0 0 0
S F T SW-A1 = 1 0 0 0 0 0 0 0
Bit1 - 8 are set.
S F T SW-A1 = 1 0 0 0 0 0 0 0
Press START key during setting.
S F T SW-A2 = 0 0 0 0 0 0 0 0
Soft SW-A2 - SW-O6 are set.
S F T SW-O6 = 0 0 0 0 0 0 0 0
To finish the settings halfway between
SW-A1 and SW-O6, press the STOP
key. In this case, the setting being done
to the SW No. on display will be nullified
while settings done to the preceding
SW No. remain in effect.
When the COPY key is pressed, the
contents of soft switches are printed.
The soft switch mode is terminated.
2–4
UX-P115U
5. Soft switch description
5.1. Soft switch
SW
NO.
SW
l
A1
DATA
NO.
1
2
3
4
5
6
7
8
SW
l
A2
Protect from echo
Forced 4800 BPS reception
Footer print
Length limitation of copy/send/
receive
CSI transmission
DIS receive acknowledgement during G3
Non-modulated carrier for V29 transmission modem
EOL detect timer
Modem speed
1
2
3
4
5
6
7
8
Sender’s
H2 mode
Communication error treatment in
TRN sending mode (reception)
CNG transmission
CED tone signal interval
1
2
SW
l
A3
SW
l
A4
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
SW
l
A5
3
4
5
6
7
8
Switch setting and function
ITEM
MR coding
Reserved
Reserved
Reserved
Reserved
Reserved
Signal transmission level
1
No
Yes
Yes
No limit
Yes
No
No
Copy/send: 60 cm
Receive: 1 m
Transmitted
NSF: Once
DIS: Twice
No
No transmitted
Twice
Yes
25s
0
0
0
13s
V.29
9600bps 7200bps
0
0
0
0
0
1
1
1
No. 1
No. 2
No. 3
No. 4
No
No
No communication error
No
No. 1
No. 2
No
Initial setting
U
0
0
0
0
0
1000ms
1
1
750ms
1
0
0
V.27 ter
4800bps 2400bps
0
0
0
0
1
0
0
0
Yes
Yes
Communication error
Yes
500ms
0
1
Yes
Protocol monitor
Line monitor
Digital line equalization setting
(Reception)
Digital line equalization setting
(Transmission)
Digital cable equalizer setting
(Reception for Caller ID)
Error criterion
Anti junk fax check
Printed at communication
error
Yes
Yes
0
0
0
0
0
0
0
0
0
1
0
0
0
No. 1
No. 2
No. 3
No. 4
No. 5
No. 6
10 ~ 20 %
Yes
2–5
0
Not printed
No
No
7.2km
1
1
7.2km
1
1
7.2km
1
1
5 ~ 10 %
No
0
0
0
0
75ms
0
0
Binary input
No. = 16 8 4 2 1
1 2 3 4 5
0 1 0 0 0
Protocol monitor (Error print)
0
0
0
1
0
0
0km
0
0
0km
0
0
0km
0
0
1
1
0
0
0
0
0
1
Remarks
UX-P115U
SW
NO.
SW
l
A6
DATA
NO.
1
2
3
4
5
6
7
8
1
2
3
4
SW
l
B1
5
6
7
8
Switch setting and function
ITEM
Reserved
End Buzzer
Disconnect the line when DIS is
received in RX mode
Equalizer freeze control (MODEM)
Equalizer freeze control 7200 BPS
only
CNG transmission in manual TX
mode
Initial compression scheme for sharp
fax in TX mode
Modem speed automatic fallback
when RX level is under -40dBm
Recall interval
1
0
Yes
No
No
Yes
On
No
Off
Yes
0
0
Yes
No
1
MR mode
H2 mode
0
Yes
No
0
Recall times
SW
l
B2
SW
l
B3
5
6
6
7
8
1
2
SW
l
B4
Dial pausing (sec./pause)
Dial tone detection (before auto dial)
Reserved
Busy tone detection (after auto dial)
4 sec.
No
3
4
5
6
7
8
No. 5
No. 6
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Auto dial mode delay timer of before
line connect
Hold key
Auto dial mode delay timer of after
line connect
Dial mode
Pulse → Tone change function by
key
Dial pulse make/break ratio (%)
Reserved
Reserved
Recalling fixed only one time when
dialing was unsuccessful without
detecting busy tone signal
7
1
8
1
2 sec.
Yes
No
Waiting time after dialing
7
8
1
2
3
4
5
0
0
1
1
Binary input
No. = 8 4 2 1
6
0
45 sec.
0
0
55 sec.
0
0
Remarks
0
1
0
1
Binary input
No. = 8 4 2 1
1 2 3 4
0 1 0 1
5
0
1
2
3
4
Initial setting
U
0
1
1
Yes
90 sec.
1
1
0
1
0
0
140 sec.
1
1
0
0
0
0
0
0
0
0
0
No. 6
No. 7
Enable
No. 1
No. 2
Tone
Enable
0 sec.
0
0
1.5 sec.
0
1
1.7 sec.
0
0
3.0 sec.
0
1
3.0 sec.
1
0
Disable
3.6 sec.
1
0
Pulse
Disable
40/60
33/67
Yes
No
2–6
4.5 sec.
1
1
0
0
1
4.0 sec.
1
1
0
0
1
1
1
0
0
1
OPTION
UX-P115U
SW
NO.
SW
l
B5
SW
l
B6
DATA
NO.
1
2
3
4
5
6
7
8
1
2
3
4
5
0
DTMF signal transmission level
(Low)
Binary input
No. = 16 8 4 2 1
1
0
Reserved
Reserved
Reserved
DTMF signal transmission level
(High)
2 3 4 5
1 0 0 1
Initial setting
U
0
1
0
0
1
Remarks
0
0
0
0
0
1
0
1
Binary input
No. = 16 8 4 2 1
1 2 3 4 5
Reserved
Reserved
Reserved
Reading slice (Binary)
0
0
0
No. 1
No. 2
1
2
Reading slice (Half tone)
3
4
5
6
7
8
1
2
3
4
SW
l
D1
1
0 0 1 0 1
6
7
8
SW
l
C1
Switch setting and function
ITEM
5
6
Line density selection
Reserved
MTF correction in half tone mode
Reserved
Number of rings for auto receive
No. 3
No. 4
Fine
Factory
setting
0
0
Factory
setting
0
0
Light
Dark
1
0
Light
0
1
Dark
1
0
0
1
Standard
No
Darker
in dark
1
1
Darker
in dark
1
1
Binary input
Automatic switching manual to auto
receive mode
Reserved
Cl detect frequency
7
8
Distinctive ringing setting (PATTERN
4 and 5 are for CANADA only)
4
5
6
7
8
Reserved
Caller ID function
Caller ID detect during CI off
Reserved
Reserved
SW
l
D2
2
3
1
4
0
1
0
0
Reception after 5 rings
No reception
OPTION
0
0
No. 7
No. 8
1
2
3
4
2
0
0
0
0
0
0
0
1
0
0
Yes
No. = 8
1
0
0
As PTT
0
0
OFF
STANDARD
PATTERN1
PATTERN2
PATTERN3
PATTERN4
PATTERN5
Yes
All times
11.5Hz
0
1
No. 1
0
0
0
0
1
1
1
13.0Hz
1
0
No. 2
0
0
1
1
0
0
1
No
Only first
2–7
20.0Hz
1
1
No. 3
0
1
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
OPTION
OPTION
UX-P115U
SW
NO.
SW
l
D3
SW
l
E1
SW
l
E2
SW
l
E3
DATA
NO.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
SW
l
F1
4
5
6
7
8
1
0
Cl off detection timer (0-1550ms setting by 50ms step)
Binary input
No. =
16 8 4 2 1
1 2 3 4 5
0 1 1 1 0
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
DTMF detection time
1
2
3
Switch setting and function
ITEM
Protection of remote reception
(5
) detect
Remote reception with GE telephone
Remote operation code figure by
external TEL (0~9)
No. 1
No. 2
Yes
50ms
0
0
80ms
0
1
100ms
1
0
No
Compatible
SW
l
F2
4
5
6
7
8
6
1
7
0
Reserved
Reserved
Reserved
2pulses
0
1
3pulses
1
0
1
0
1
0
1
8
1
No
1pulse
0
0
0
0
1
Binary input
8 4 2 1
Yes
No. 4
No. 5
120ms
1
1
Not compatible
No. =
CNG detection in STAND-BY mode
Reserved
Reserved
Number of CNG detect (STAND-BY
mode)
Remarks
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
5
0
1
2
3
Initial setting
U
0
1
1
1
0
1
0
0
4pulses
1
1
0
1
0
0
0
2–8
OPTION
UX-P115U
SW
NO.
SW
l
G1
SW
l
G2
SW
l
G3
SW
l
H1
SW
l
H2
SW
l
I1
SW
l
I2
DATA
NO.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
ITEM
Switch setting and function
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
2–9
0
Initial setting
U
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Remarks
UX-P115U
SW
NO.
SW
l
I3
SW
l
I4
SW
l
I5
SW
l
I6
SW
l
I7
SW
l
J1
DATA
NO.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
Switch setting and function
ITEM
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Sender’s phone number setting
Reserved
Reserved
Summer time setting
Ringer volume
1
0
Cannot change
Change allowed
No
No. 1
No. 2
Off
0
0
Low
0
0
Low
0
1
Low
0
1
Yes
Middle
1
0
Middle
1
0
High
1
1
High
1
1
No. 4
No. 5
Low
0
0
Low
0
1
Middle
1
0
High
1
1
No. 7
No. 8
7
8
Speaker volume (3 stages)
1
2
SW
l
J2
3
Reserved
Handset receiver volume
4
5
6
7
8
Initial setting
U
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
Remarks
OPTION
OPTION
1
0
OPTION
1
0
0
Reserved
Reserved
Reserved
OPTION
1
0
0
0
0
2 – 10
UX-P115U
SW
NO.
SW
l
J3
SW
l
K1
SW
l
L1
DATA
NO.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
SW
l
L2
SW
l
M1
SW
l
M2
SW
l
N1
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Switch setting and function
ITEM
1
Reserved
Communication results printout
(Transaction report)
E/T/M
No. 2
No.3
No. 4
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Cut off mode (COPY mode)
A4 paper enable
LEGAL & LETTER paper enable
Reserved
Paper set size
Reception reduction ratio in case of
memory full
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Send
only
0
0
1
0
0
0
Yes
Enable
Enable
LETTER
0
0
Auto
No. 4
No. 5
No. 6
100 %
Always
No print
Err only
0
1
0
0
1
1
1
0
0
No
Disable
Disable
No. 1
No. 2
Automatic reduce of receive
Print contrast
Initial setting
U
0
0
Normal
0
0
0
Lighter
0
0
1
LEGAL
0
1
100 %
Light
0
1
0
93 %
A4
1
0
Dark
0
1
1
OPTION
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
0
OPTION
OPTION
0
0
1
Darker
1
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2 – 11
Remarks
OPTION
OPTION
UX-P115U
SW
NO.
SW
l
N2
SW
l
N3
SW
l
O1
SW
l
O2
SW
l
O3
SW
l
O4
SW
l
O5
DATA
NO.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
ITEM
Switch setting and function
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
2 – 12
0
Initial setting
C
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Remarks
UX-P115U
SW
NO.
SW
l
O6
DATA
NO.
1
2
3
4
5
6
7
8
ITEM
Switch setting and function
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
2 – 13
0
Initial setting
C
0
0
0
0
0
0
0
0
Remarks
UX-P115U
5.2. Soft switch function description
SW-A2 No. 6 H2 mode
SW-A1 No. 1 Protect from echo
Used to determine reception of H2 mode (15 sec transmission mode).
When set to OFF, H2 mode reception is inhibited even though the
transmitting machine has H2 mode function.
Used to protect from echo in reception.
SW-A1 No. 2 Forced 4800BPS reception
SW-A2 No. 7 Communication error treatment in RTN sending
mode (Reception)
When line conditions warrant that receptions take place at 4800 BPS
repeatedly.
Used to determine communication error treatment when RTN is sent
by occurrence of a received image error in G3 reception. When it is set
to "1", communication error is judged as no error.
It may improve the success of receptions by setting at 4800BPS.
This improves the receiving document quality and reduces handshake
time due to fallback during training.
SW-A2 No. 8 CNG transmission
When set to "0", this model allows CNG transmission by pressing the
Start key in the key pad dialing mode. When set to "1", CNG transmission in the key pad dialing mode cannot be performed. In either case.
CNG transmission can be performed in the auto dial mode.
SW-A1 No. 3 Footer print
When set to "1", the date of reception, the sender machine No., and
the page No. are automatically recorded at the end of reception.
SW-A1 No. 4 Length limitation of copy/send/receive
SW-A3 No. 1, No. 2 CED tone signal interval
Used to set the maximum page length.
For international communication, the 2100Hz CED tone may act as an
echo suppression switch, causing a communication problem.
To avoid possible paper jam, the page length is normally limited to 0.6
meter for copy or transmit, and 1 meters for receive.
Though SW-A3 No. 1 and No. 2 are normally set to 0, this setting is
used to change the time between the CED tone signal to eliminate the
communication caused by echo.
It is possible to set it to "No limit" to transmit a long document, such as
a computer print form, etc. (In this case, the receiver must also be set
to no limit.)
TX
SW-A1 No. 5 CSI transmission
RX
CED
(CSI TRANSMISSION) is a switch to set whether the machine sends
or does not send the signal (CSI signal) informing its own telephone
No. to the remote fax machine when information is received. When
"nonsending" is set, the telephone No. is not output on the remote
transmitting machine if the remote transmitting machine has the function to display or print the telephone No. of receiving machine, using
this CSI signal.
T
DIS
SW-A3 No. 3 MR Coding
MR Coding is enable.
SW-A1 No. 6 DIS receive acknowledgment during G3 transmission
SW-A3 No. 4 ~ No. 8 Reserved
Used to make a choice of whether reception of DIS (NSF) is acknowledged after receiving two DISs (NSFs) or receiving one DIS (two
NSFs).
SW-A4 No. 1 ~ No. 5 Signal transmission level
Set to "0".
Used to control the signal transmission level in the range of-0dB to31dB.
It may be useful for overseas communication to avoid an echo suppression problem, if set to 1.
SW-A4 No. 6 Protocol monitor (Error print)
SW-A1 No. 7 Non-modulated carrier for V29 transmission modem
If set to "1", protocol is printed at communication error.
Though transmission of a non-modulated carrier is not required for
transmission by the V29 modem according to the CCITT recommendation, it may be permitted to a send non-modulated carrier before the
image signal to avoid an echo suppression problem. It may be useful
for overseas communication to avoid an echo suppression problem, if
set to 1.
SW-A4 No. 7 Protocol monitor
Normally set to "0". If set to "1", communication can be checked, in
case of trouble, without using a G3 tester or other tools.
When communication FSK data transmission or reception is made, the
data is taken into the buffer. When communication is finished, the data
is analyzed and printed out. When data is received with the line monitor (SW-A4 No. 8) set to "1" the reception level is also printed out.
SW-A1 No. 8 EOL (End Of Line) detect timer
Used to make a choice of whether to use the 25-second or 13-second
timer for detection of EOL.
SW-A4 No. 8 Line monitor
This is effective to override communication failures with some facsimile models that have longer EOL detection.
Normally set to "0". If set to "1", the transmission speed and the reception level are displayed on the LCD. Used for line tests.
SW-A2 No. 1 ~ No. 4 Modem speed
SW-A5 No. 1, No. 2 Digital line equalization setting (Reception)
Used to set the initial modem speed. The default is 9600BPS.
Line equalization when reception is to be set according to the line
characteristics.
It may be necessary to program it to a slower speed when frequent
line fallback is encountered, in order to save the time required for fallback procedure.
Setting should be made according to distance between the telephone
and the telephone company central switching station.
SW-A2 No. 5 Sender’s information transmit
SW-A5 No. 3, No. 4 Digital line equalization setting (Transmission)
(SENDER’S INFORMATION TRANSMISSION) is a switch to set the
function to print the content of HEADER PRINT described in the passcode list at the front end of receiver’s original when original is sent to
the remote machine.
Line equalization when transmitter is to be set according to the line
characteristics.
Setting should be made according to distance between the telephone
and the telephone company central switching station.
If this switch is set to "NO", the HEADER PRINT is not output at the
receiving machine.
2 – 14
UX-P115U
SW-B2 No. 3 Reserved
SW-A5 No. 5, No. 6 Digital cable equalizer setting (Reception for
Caller ID)
Set to "0".
Line equalization when reception for CALLER ID is to be set according
to the line characteristics.
SW-B2 No. 4 Busy tone detection (after auto dial)
Setting should be made according to distance between the telephone
and the telephone company central switching station.
Used to set busy tone detection in auto dialing.
SW-A5 No. 7 Error criterion
This is time waiting for the opponent’s signals after dialing.
Used to select error criterion for sending back RTN when receiving
image data.
SW-B2 No. 7, No. 8 Reserved
SW-B2 No. 5, No. 6 Waiting time after dialing
Set to "0".
SW-A5 No. 8 Anti junk fax check
SW-B3 No. 1 ~ No. 5 Reserved
When using the Anti junk fax function, set to "1".
Set to "0".
SW-A6 No. 1 Reserved
SW-B3 No. 6, No. 7 Auto dial mode Delay timer of before line connect
Set to "0".
Delay time between the dial key input and line connection under the
auto dial mode.
SW-A6 No. 2 End buzzer
Setting this bit to 0 will disable the end buzzer (including the error
buzzer/on-hook buzzer).
RAPID01
SW-A6 No. 3 Disconnect the line when DIS is received in RX
mode
CML RELAY ON
DIALLING
Bit1= 0: When DIS signal is received during RX mode, the line is disconnected immediately.
Bit1= 1: When DIS signal is received during RX mode, the line is disconnected on the next tone.
SW-A6 No. 4 Equalizer freeze control (MODEM)
This switch is used to perform reception operation by fixing the equalizer control of modem for the line which is always in an unfavorable
state and picture cannot be received.
No.6
No.7
0
0
1
1
0
1
0
1
0sec
1.5sec
3.0sec
4.5sec
SW-B3 No. 8 Hold key
Used to set YES/NO of holding function by the Hold key.
* Usually, the control is executed according to the state of line where
the equalizer setting is changed always.
SW-A6 No. 5 Equalizer freeze control 7200BPS only
SW-B4 No. 1, No. 2 Auto dial mode Delay timer of after line connect
Setting which specifies SW-A3 No. 6 control only in the condition of
7200BPS modem speed.
Delay time between the line connection and dial data output under the
auto dial mode.
SW-A6 No. 6 CNG transmission in manual TX mode
RAPID01
When set to "1", fax transmit the CNG signal in case of manual transmission mode (User press the START key after waiting for the fax
answering signal from handset or speaker).
SW-A6 No. 7 Initial compression scheme for sharp fax in TX mode
When set to "0", if the other fax is Sharp model, fax transmit the document by H2 mode. When set to "1", even if the other fax is Sharp
model, fax transmits the document by MR mode.
SW-A6 No. 8 Modem speed automatic fallback when RX level is
under -40dBm
DIAL DATA
CML RELAY ON
No.1
No.2
0
0
1
1
0
1
0
1
1.7sec
3.0sec
3.6sec
4.0sec
SW-B4 No. 3 Dial mode
When using the pulse dial, set to 1. When using the tone dial, set to 0.
When set to "1", if fax signal level is under -40dBm during reception,
machine selects the slower modem speed automatically.
SW-B4 No. 4 Pulse → Tone change function by
It is effective when noises occur on the received document due to the
long distance communications.
When setting to 1, the mode is changed by pressing the
the pulse dial mode to the tone dial mode.
SW-B1 No. 1 ~ No. 4 Recall interval
SW-B4 No. 5 Dial pulse make/break ratio (%)
Choice is made for a redial interval for speed and rapid dial calls.
When using the 33% make ratio pulse dial, set to "0".
Use a binary number to program this. If set to 0 accidentally, 1 will be
assumed.
When using the 40% make ratio pulse dial, set to "1".
SW-B1 No. 5 ~ No. 8 Recall times
SW-B4 No. 6, No. 7 Reserved
Choice is made as to how many redials there should be.
Set to "0".
SW-B2 No. 1 Dialing pause (sec/pause)
Pauses can be inserted between telephone numbers of direct dial connection. Selection of 4 sec or 2 sec pause is available.
SW-B2 No. 2 Dial tone detection (before auto dial)
Used to set YES/NO of dial tone detection in auto dialing.
2 – 15
key
key from
UX-P115U
SW-D1 No. 5 Automatic switching manual to auto receive mode
SW-B4 No. 8 Recalling fixed only one time when dialing was
unsuccessful without detecting busy tone signal
This soft switch is used to select whether the machine should switch to
the auto receive mode after 5 rings in the manual receive mode or
remain in the same way as SW-D1 No. 1, No. 2, No. 3 and No. 4
"0"1"0"1"(5 rings).
When dialing results in failure since the busy tone cannot be detected,
recalling is fixed to one time.
Supplementary explanation
SW-D1 No. 6 Reserved
If time-out termination is made when dialing, only single recall is possible even if the setting time of recalls (SW-B1 No. 5 - No. 8) has been
set to some times. This soft switch is added in order to meet FCC.
Set to "0".
SW-D1 No. 7, No. 8 CI detect frequency
SW-B5 No. 1 ~ No. 5 DTMF signal transmission level (Low)
Detection frequency of ring signal for auto reception is set.
When set to No. 6=0, No. 7=0, frequency is set to PTT recommendation.
When set to No. 6=0, No. 7=1, frequency is set to 11.5Hz or more.
When set to No. 6=1, No. 7=0, frequency is set to 13.0Hz or more.
When set to No. 6=1, No. 7=1, frequency is set to 20.0Hz or more.
The transmission level of DTMF signal is adjusted. (lower frequency)
00000: 0dBm
↓
11111: -15.5 dBm (-0.5dBm x 31)
SW-D2 No. 1 ~ No. 3 Distinctive ringing setting (PATTERN 4 and 5
are for CANADA only)
SW-B5 No. 6 ~ No. 8 Reserved
Set to "0".
This function allows reception of services offered by USA and Canada
telephone companies in which the customer contracts with the telephone company to have up to 4 telephone numbers (USA) or 6 telephone numbers (Canada) established for one line.
SW-B6 No. 1 ~ No. 5 DTMF signal transmission level (High)
The transmission level of DTMF signal is adjusted. (higher frequency)
00000: 0dBm
Each telephone number is signaled by a different ringing pattern, and
the customer can allocate each number to a specific use.
↓
11111: -15.5 dBm (-0.5dBm x 31)
<Example of use>
SW-B6 No. 6 ~ No. 8 Reserved
Phone Number
Set to "0".
Ring Pattern
SW-C1 No. 1, No. 2 Reading slice (Binary)
Used to determine the set value of reading density in standard/fine
mode. The standard setting is "00" (Factory setting is "00")
SW-C1 No. 3, No. 4 Reading slice (Half tone)
555-1234
555-1235
555-1236
555-1237
Intended
Purpose
Voice Calls
Facsimile Calls
Answering
PC Modem
Ring Pattern
Standard
Pattern 1
Pattern 2
Pattern 3
<Distinctive Ringing Timing Specifications>
Used to determine the set value of reading density in half tone mode.
The standard setting is "00" (Factory setting is "00")
1) USA
DISTINCTIVE RING → 1:RING PATTERN 1 → 2:RING PATTERN 2
↑
↓
5:OFF SETTING
← 4:STANDARD RING ← 3:RING PATTERN 3
SW-C1 No. 5 Line density selection
Used to set the transmission mode which is automatically selected
when the Resolution key is not pressed. In the copy mode, however,
the fine mode is automatically selected unless the Resolution key is
manually set to another mode.
2) Canada
DISTINCTIVE RING → 1:RING PATTERN 1 → 2:RING PATTERN 2
↓
↑
7:OFF SETTING
3:RING PATTERN 3
↑
↓
6:STANDARD RING ← 5:RING PATTERN 5 ← 4:RING PATTERN 4
SW-C1 No. 6 Reserved
Set to "0".
SW-C1 No. 7 MTF correction in half tone mode
•
This allows selection of MTF correction (dimness correction) in the half
tone mode.
Ring Pattern
STANDARD has 5 ring patterns, and DISTINCTIVE has 9 patterns,
Ring Patterns 1~4 for USA, and 5~9 for Canada. However, to make
the setting procedure as easy as possible for the user to understand these patterns are grounded as follows:
When "NO" (=1) is selected, the whole image becomes soft and mild.
Clearness of characters will be reduced. Normally set to "YES" (=0).
SW-C1 No. 8 Reserved
Set to "0".
<Optional Setting>
1) RING PATTERN 1
SW-D1 No. 1 ~ No. 4 Number of rings for auto receive
When the machine is set in the auto receive mode, the number of rings
before answering can be selected. It may be set from one to four rings
using a binary number. Since the facsimile telephone could be used as
an ordinary telephone if the handset is taken off the hook, it should be
programmed to the user’s choice. If the soft switch was set to 1, direct
connection is made to the facsimile. If a facsimile calling beep was
heard when the handset is taken off the hook, press the START key
and put the handset on the hook to have the facsimile start receiving. If
it was set to 0 accidentally, receive ring is set to 1.
2) RING PATTERN 2
3) RING PATTERN 3
4) RING PATTERN 4
5) RING PATTERN 5
6) STANDARD RING
7) OFF SETTING
NOTE: If the machine is set to answer after a large number of rings, it
may not be able to receive faxes successfully. If you have difficulty receiving faxes, reduce the number of rings to a maximum of 6.
2 – 16
RING PATTERN 1
RING PATTERN 4
RING PATTERN 5
RING PATTERN 2
RING PATTERN 6
RING PATTERN 3
RING PATTERN 7
RING PATTERN 8
RING PATTERN 9
for USA
for USA
for Canada
for USA
for Canada
for USA
for Canada
for Canada
for Canada
UX-P115U
01110 (50ms ~ 14):
700ms (CI interruption>700ms:Judged as a CI OFF section)
The section 1 is not judged as a CI OFF section, the CI signal A is
counted as one signal.
The section 2 is judged as a CI OFF section, the CI signal B is
considered as the second signal.
2S ring
STANDARD
4S ring
2S ring
2S ring
00111 (50ms ~ 7):
1.5S ring
350ms (CI interruption>350ms:Judged as a CI OFF section)
The section 1 is judged as a CI OFF section, and the CI signal A is
counted as two signals.
The section 2 is judged as a CI OFF section, and the CI signal B is
considered as the third signal.
3S ring
1S ring
4S ring
1.5S ring
0.5S
RING
PATTERN 1
for USA
RING
PATTERN 2
for USA
RING
PATTERN 3
for USA
RING
PATTERN 4
for USA
RING
PATTERN 5
for CANADA
RING
PATTERN 6
for CANADA
RING
PATTERN 7
for CANADA
RING
PATTERN 8
for CANADA
RING
PATTERN 9
for CANADA
0.8S
SW-D3 No. 6 ~ No. 8 Reserved
4S ring
0.5S
Set to "0".
0.8S
1S
0.3S
0.2S
SW-E1 No. 1 ~ No. 8 Reserved
4S ring
0.4S
Set to "0".
0.3S
SW-E2 No. 1 ~ No. 8 Reserved
4S ring
0.2S
Set to "0".
0.4S 0.4S 0.8S
SW-E3 No. 1 ~ No. 8 Reserved
4S ring
0.2S 0.2S
1S
1S
Set to "0".
SW-F1 No. 1, No. 2 DTMF detect time
4S ring
1S
1S
1S
Used to set detect time of DTMF (Dual Tone Multi Frequency) used in
remote reception (5
).
The longer the detect time is, the less the error detection is caused by
noises.
0.5S
0.5S
1S
0.5S
0.5S
0.5S
0.5S
0.5S
0.5S
SW-F1 No. 3 Protection of remote reception (5
1S
Used to set the function of remote reception (5
"1", the remote reception function is disabled.
0.5S
0.25S 0.25S 0.25S
) detect
). When set to
SW-F1 No. 4 Remote reception with GE telephone
0.2S 0.2S
(Corresponding to TEL mode by GE) P. B. X.
0.25S 0.25S
"1": Compatible with TEL mode by GE
0.2S
"0": Not compatible
6S
•
When sending (5
) for remote reception with a GE manufactured telephone remote reception may not take place because of
special specifications in their DTMF. To overcome this, a soft SW is
provided to change the modem setting to allow for remote reception.
•
If this soft SW is set to "1", other telephone sets may be adversely
affected.
SW-D2 No. 4 Reserved
Set to "0".
SW-D2 No. 5 Caller ID function
Used for Caller ID function.
SW-F1 No. 5 ~ No. 8 Remote operation code figure by external
TEL (0 ~ 9)
SW-D2 No. 6 Caller ID detect during CI off
Detection of caller ID signal is performed as follows:
0:First CI OFF only
1:All of CI OFF
Remote operation codes can be changed from 0 through 9. If set to
greater than 9, it defaults to 9. The "5
" is not changed.
Ex-7
(Default: 5
)
SW-D2 No. 7, No. 8 Reserved
SW-F2 No. 1 CNG detection in STAND-BY mode
Set to "0".
When setting to "1", the CNG signal detection function during stand-by
stops.
SW-D3 No. 1 ~ No. 5 CI off detection timer (0-1550ms setting by
50ms step)
SW-F2 No. 2, No. 3 Reserved
Set the minimum time period of CI signal interruption which affords to
be judged as a CI OFF section with 50ms steps.
(Example).
A
Set to "0".
SW-F2 No. 4, No. 5 Number of CNG detect (STAND-BY mode)
Used for detection of CNG in 1 to 4 pulses.
B
SW-F2 No. 6 ~ No. 8 Reserved
Set to "0".
400msec
2000msec
1
2
SW-G1 No. 1 ~ No. 8 Reserved
Set to "0".
2 – 17
UX-P115U
SW-J3 No. 2 ~ No. 4 Communication result printout (Transaction
report)
SW-G2 No. 1 ~ No. 8 Reserved
Set to "0".
Every communication, the result can be output. As usual, it is set to
print the timer sending communication error alone. If No. 2: 0 No. 3: 1
No. 4: 0 are set, printing is always on (printed even if it is normally
ended).
SW-G3 No. 1 ~ No. 8 Reserved
Set to "0".
SW-H1 No. 1 ~ No. 8 Reserved
000: Error, timer and memory sending/receiving
Set to "0".
001: Sending
SW-H2 No. 1 ~ No. 8 Reserved
010: Continuous printing
Set to "0".
011: Not printed
SW-I1 No. 1 ~ No. 8 Reserved
100: Communication error
Set to "0".
SW-J3 No. 5 ~ No. 8 Reserved
SW-I2 No. 1 ~ No. 8 Reserved
Set to "0".
Set to "0".
SW-K1 No. 1 ~ No. 8 Reserved
SW-I3 No. 1 ~ No. 8 Reserved
Set to "0".
Set to "0".
SW-L1 No. 1 ~ No. 4 Reserved
SW-I4 No. 1 ~ No. 8 Reserved
Set to "0".
Set to "0".
SW-L1 No. 5 Cut off mode (COPY mode)
SW-I5 No. 1 ~ No. 8 Reserved
Whether the excessive part is printed on the next recording paper or
discarded is selected to copy a document which is longer than the
recording paper.
Set to "0".
SW-I6 No. 1 ~ No. 8 Reserved
SW-L1 No. 6 A4 Paper enable
Set to "0".
The use of recording paper of A4 is enabled.
SW-I7 No. 1 ~ No. 8 Reserved
SW-L1 No. 7 LEGAL and LETTER paper enable
Set to "0".
The use of recording paper of LEGAL and LETTER is enabled.
SW-J1 No. 1, No. 2 Reserved
SW-L1 No. 8 Reserved
Set to "0".
Set to "0".
SW-J1 No. 3 Sender’s phone number setting
SW-L2 No. 1, No.2 Paper set size
Used to make a choice of whether the registered sender’s phone number can be changed or not. If the switch is set to "1", new registration
of the sender’s phone number is disabled to prevent accidental wrong
input.
At present size of the recording paper.
SW-L2 No. 3 Automatic reduce of receive
If set to 1, it is reduced automatically when receiving.
SW-J1 No. 4, No. 5 Reserved
SW-L2 No. 4 ~ No. 6 Print contrast
Set to "0".
Used for adjustment of print contrast.
SW-J1 No. 6 Summer time setting
SW-L2 No. 7 Reception reduction ratio in case of memory full
This is used to set YES/NO of automatic clock adjustment for European Summer time.
This model is designed so that the print is started according to the setting of SW-L2 No. 3 when reception of one page is completed. However, if the memory is filled with data before completion of reception of
one page, the print is started with the reduction ratio which is set with
this switch.
SW-J1 No. 7, No. 8 Ringer volume
Used to adjust ringing volume.
SW-J2 No. 1, No. 2 Speaker volume (3 stages)
SW-L2 No. 8 Reserved
Used to adjust sound volume from a speaker.
Set to "0".
SW-J2 No. 3 Reserved
SW-M1 No. 1 ~ No. 8 Reserved
Set to "0".
Set to "0".
SW-J2 No. 4, No. 5 Handset receiver volume
SW-M2 No. 1 ~ No. 8 Reserved
Used to adjust sound volume from a handset receiver volume.
Set to "0".
SW-J2 No. 6 ~ No. 8 Reserved
SW-N1 No. 1 ~ No. 8 Reserved
Set to "0".
Set to "0".
SW-J3 No. 1 Reserved
SW-N2 No. 1 ~ No. 8 Reserved
Set to "0".
Set to "0".
SW-N3 No. 1 ~ No. 8 Reserved
Set to "0".
2 – 18
UX-P115U
SW-O1 No. 1 ~ No. 8 Reserved
Set to "0".
SW-O2 No. 1 ~ No. 8 Reserved
Set to "0".
SW-O3 No. 1 ~ No. 8 Reserved
Set to "0".
SW-O4 No. 1 ~ No. 8 Reserved
Set to "0".
SW-O5 No. 1 ~ No. 8 Reserved
Set to "0".
SW-O6 No. 1 ~ No. 8 Reserved
Set to "0".
2 – 19
UX-P115U
[3] Troubleshooting
•
Refer to the following actions to troubleshoot any of the problems
mentioned in 1-4.
Apply line equalization SOFT SWITCH A2-1, 2, 3, 4.
May be used in case [1] [2] [3] [4].
•
Slow down the transmission speed SOFT SWITCH A2-1, 2, 3, 4.
May be used in case [2] [3].
•
Replace the TEL/LIU PWB.
May be used in all cases.
•
Replace the control PWB.
May be used in all cases.
•
If transmission problems still exist on the machine, use the following format and check the related matters.
[1] A communication error occurs.
[2] Image distortion produced.
[3] Unable to do overseas communication.
[4] Communication speed slow due to FALLBACK.
•
In crease the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5.
May be used in case [1] [2] [3].
•
Decrease the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5.
May be used in case [3].
TO:
ATT:
Ref.No. :
CC:
ATT:
Date
:
Dept
:
Sign
:
FM:
From: Mr.
Our customer
Other party
Problem mode
***** Facsimile communication problem *****
Fax Tel No.:
Name
Address
Contact person
Name
Address
Contact person
Line: Domestic / international
Reception / Transmission
Frequency:
Confirmation
item
Our customer
A1
A2
Ref.No.:
Date:
Model:
G3
Automatic reception / Manual reception
Automatic dialing / Manual dialing / Others
% ROM version:
Other party
B1
B2
C1
D2
C2
E1
E2
Our service
D1
Other party's service
Comment
Countermeasure
**** Please attach the G3 data and activity report on problem. ****
* Please complete this report before calling the "TAC" hotline if problem still occurs.
2 – 20
Tel No.
Fax No.
Model name
Tel No.
Fax No.
Model name
Phase: A, B, C, D.
Please mark problem with an X.
No problem is: 0.
A1 A2 B1 B2 C1 C2 D1 D2 E1 E2
Transmission level setting is (
customer
Transmission level (
) dBm
Reception level (
) dBm
By level meter at B1 and B2
) dB at our
UX-P115U
[4] Error code table
1. Communication error code table
1.1. G3 Transmission
Code
0
1
Final received signal
Incomplete signal frame
NSF, DIS
2
3
4
CFR
FTT
MCF
5
PIP or PIN
6
7
8
RTN or RTP
No signal or DCN
-
11
-
12
13
-
Error Condition (Receiver side)
Cannot recognize bit stream after flag
Cannot recognize DCS signal by echo etc.
Cannot recognize NSS signal (FIF code etc)
Disconnects line during reception (carrier missing etc)
Disconnects line by fall back
Disconnects line during reception of multi page
Cannot recognize NSS, DCS signal in the case of mode change
The line is hung up without replying to telephone request from the receiving party.
Cannot recognize NSS, DCS signal after transmit RTN or RTP signal.
No response in receiver side or DCN signal received* (transmitter side)
Owing to error in some page the error could not be corrected although the specified number of error
retransmissions were attempted.
Error occurred after or while reception by the remote (receiving) machine was revealed to be
impossible.
Error occurred just after fallback.
Error occurred after a response to retransmission end command was received.
1.2. G3 Reception
Code
0
1
Final received signal
Incomplete signal frame
NSS, DCS
2
3
4
5
6
7
8
9
10
11
NSC, DTC
EOP
EOM
MPS
PR1-Q
No signal or DCN
-
12
13
-
Error Condition (Receiver side)
Cannot recognize bit stream after flag
Cannot recognize CFR or FTT signal
Disconnects line during transmission (line error)
Cannot recognize NSS signal (FIF code etc)
Cannot recognize MCF, PIP, PIN, RTN, RTP signal
Cannot recognize MCF, PIP, PIN, RTN, RTP signal in the case of mode change
The line is hung up without replying to communication request.
Cannot recognize PIP, PIN signal in the case of TALK request
No response in transmitter (cannot recognize DIS signal) or DCN signal received* (receiver side)
Error occurred upon completion of reception of all pages.
Error occurred when mode was changed or Transmission/Reception switching was performed.
Error occurred during partial page or physical page reception.
Error occurred after or during inquiry from the remote (transmitting) machine as to whether reception is possible or not.
Error occurred during or just after fallback.
Error occurred after the retransmission end command was received.
2 – 21
UX-P115U
UX-P115U
FAX
Service
E
Market
Manual 3. MECHANISM BLOCKS
CHAPTER
3.2. Automatic document feed
1) Use of the paper feed roller and separate plate ensures error-free
transport and separation of documents. The plate spring presses
the document to the paper feed roller to assure smooth feeding of
the document.
[1] General description
1. Document feed block and diagram
2) Document separation method: Separate plate
Document
Document guide upper
Paper feed plate
Front sensor
Document
Separate rubber
Document
sensor
Separate plate
Back roller
Paper feed roller
Paper feed roller
CIS
Fig. 3
3.3. Documents applicable for automatic feed
Fig. 1
2. Document feed operation
Paper weight
1) The original, which is set in the document hopper, feeds automatically when the front sensor is activated. This in turn activates the
pulse motor which drives the document supply roller. The document stops when the lead edge is detected by the document sensor.
Paper thickness (ref.)
Paper size
2) The lead edge of the original is fed a specified number of pulses
after the lead edge of the document is detected for the reading process to begin.
Feeder capacity
10 sheets
1sheet(Manual)
70 kg
70 kg ~ 135 kg
80 g/m2
52 g/m2 ~ 157g/m2
0.1 mm
0.1 mm ~ 0.18mm
LGL (216 mm x 355.6 mm)
A4 (210 mm x 297 mm)
LTR (216 mm x 279 mm)
A4/LTR: 10 sheets
LGL : 1 sheet
NOTE: Double-side coated documents and documents on facsimile
recording paper should be inserted manually. The document
feed quantity may be changed according to the document
thickness.
3) The trailing edge of the original is fed a specific number of pulses
after the trailing edge of the document deactivates the document
sensor. The read process then stops and the original is discharged.
4) When the front sensor is in the OFF state (any document is not set
up in the hopper guide), the drive will be stopped when the document is discharged.
Documents corresponding to a paper weight heavier than 70 kg (80 g/
m2) and lighter than 135 kg (157 g/m2) are acceptable for manual
feed.
3. Hopper mechanism
Documents heavier than 135 kg (157 g/m2) in terms of the paper
weight must be duplicated on a copier to make it operative in the facsimile.
3.1. General view
3.4. Loading the documents
1. Make sure that the documents are of suitable size and thickness,
and free from creases, folds, curls, wet glue, wet ink, clips, staples
and pins.
2. Place documents face down in the hopper.
i)
Adjust the document guides to the document size.
ii) Align the top edge of documents and gently place them into the
hopper. The first page under the stack will be taken up by the
feed roller to get ready for transmission.
NOTE: 1) Curled edge of documents, if any, must be straightened
out.
Fig. 2
The hopper section contains document guides that are used to adjust
the hopper to the width of the original document. This ensures that the
original feeds straight into the fax machine for scanning.
2) Do not load the documents of different sizes and/or thicknesses together.
Document width: 148 mm to 216 mm (A5 longitudinal size to Letter
longitudinal size)
NOTE: Adjust the document guide after setting up the document.
3–1
UX-P115U
5.2.3 Recording paper transfer sequence
Back of
document
1) The recording paper stored in the paper tray ass’y is fed with the
PU roller, and is stopped when the P-IN sensor is turned on by
sensing its lead edge.
Last page of
document
Paper feed plate
2) Hereafter, the imaging film and recording paper are transferred with
the recording paper feed roller, and thermal transcription is performed on the recording paper.
First page of
document
Separate
rubber
3) After thermal transcription, the imaging film is taken up by the roller
on the take-up side, and the recording paper is discharged by the
back roller.
Separate
plate
Troubleshooting the density unevenness mainly results from the
longitudinal misalignment of the thermal head to the heater line.
Otherwise, the head is in uneven contact with the recording paper
feed roller, or the imaging film is wrinkled.
Paper feed roller
The following items are described as the simplified checking
method.
Fig. 4
a) Are the power and signal cables of the thermal head suitably
treated?
3.5. Documents requiring use of the copy
1) Documents smaller than 148mm (W) x 140mm (L).
2) Documents thinner than the thickness of 0.06mm.
b) Does the same symptom appear even if the thermal head pressure spring is replaced?
3) Documents containing creases, folds, or curls, especially those
whose surface is curled (maximum allowable curl is 5mm).
c) Is the feed roller of the recording paper concentric? (Density is
uneven at intervals.)
4) Documents containing tears.
d) Does the same symptom appear even if the thermal head is
replaced?
5) Carbon-backed documents. (Insert a white sheet of paper between
the carbon back and the document carrier to avoid transfer of carbon to the carrier.)
e) Is the imaging film stained or wrinkled?
5.3. General view
6) Documents containing an easily separable writing material (e.g.,
those written with a lead pencil).
7) Transparent documents.
8) Folded or glued documents.
4. Document release
Paper
tray
extension
(Accessory)
4.1. General
To correct a jammed document or to clean the document running surface, pull the insertion side of document center of the operation panel.
To open the upper document guide, the operation panel must be
opened first.
Feed plate
5. Recording block
Paper
tray ass'y
(Accessory)
Separate rubber
5.1. Driving
In the drive mechanism, the rotating force of the pulse motor for both
transmission and reception is transmitted to the paper supply roller,
the recording paper feed roller and imaging film drive gear through the
pulse motor axle gear, reduction gear and planetary gear.
P-IN sensor lever
(Upper)
PU roller
Platen roller
5.2. Recording
Release lever
This equipment employs the thermal transcription system which uses
the thermal head imaging film.
Imaging film
(Supply side)
Thermal head
Film sensor lever
5.2.1 Thermal head
The thermal head is composed of 2,016 heating elements in traverse
line, and the resolution power is 8 dots/mm. The maximum speed is 10
ms/line.
Imaging film
(Take-up side)
Fig. 5
5.2.2 Structure of recording mechanism
Recording is achieved by applying a suitable pressure to the thermal
head through the imaging film of the recording paper feed roller and
the recording paper.
The main scanning is electronically performed, and the sub-scanning
is mechanically performed (by sending the recording paper with the
recording paper feed roller).
3–2
UX-P115U
[2] Disassembly and assembly procedures
•
This chapter mainly describes the disassembly procedures. For the assembly procedures, reverse the disassembly procedures.
•
Easy and simple disassembly/assembly procedures of some parts and units are omitted. For disassembly and assembly of such parts and units,
refer to the Parts List.
•
The numbers in the illustration, the parts list and the flowchart in a same section are common to each other.
•
To assure reliability of the product, the disassembly and the assembly procedures should be performed carefully and deliberately.
1
Parts list (Fig. 1)
Bottom plate, PWB's and drive unit
No.
2
Qty
No.
1
Mechanism uni
Part name
1
9
Connector
1
2
Screw (3x10)
5
10
TEL/LIU PWB unit
1
3
Screw
1
11
Connector
6
4
AC cord earth cable
1
12
Screw (3x10)
1
5
Bottom plate
1
13
Hook
1
6
Hook
1
14
Control PWB unit
1
7
Connector
1
15
Wire holder PWB
1
8
Power supply PWB unit
1
16
Screw (3x10)
2
17
Drive unit
1
2
2
4
Power supply PWB unit
8
AC cord
7
5
Bottom plate
4
10 TEL/LIU PWB unit
Washer
3
15
9
11
11
Push
11
11
15
14
Control PWB unit
16
11
16
6
17
Drive unit
12
13
1 Mechanism unit
Fig. 1
3–3
Part name
Qty
UX-P115U
2
Parts list (Fig. 2)
Operation panel unit, top cover unit
and sub frame unit
No.
NOTE: For disassembly of the inside of the unit,
refer to the exploded view in the parts
guide.
Qty
No.
1
Mechanism unit
1
5
Screw (3x12)
4
2
Stopper plate
1
6
Operation panel unit
1
3
4
Part name
Operation panel unit/
top cover unit/ sub frame unit
1
Panel cable cover
1
Part name
Qty
7
Screw (3x10)
2
8
Hook
7
9
Top cover unit
1
10
Sub frame unit
1
Operation
6 panel unit
8
8
10 Sub frame
unit
8
5
P-IN
lever
8
5
9
Top cover
unit
8
8
7
5
5
7
3
Screwdriver
4
Hook
Screwdriver
1
Mechanism unit
2
NOTE: When removing the operation
panel unit, detach the stopper
plate at first.
Fig. 2
3–4
UX-P115U
3
CIS unit and thermal head unit
Parts list (Fig. 3)
No.
NOTE: For disassembly of the inside of the unit,
refer to the exploded view in the parts
guide.
Qty
No.
1
Mechanism unit
Part name
1
4
Head cover
Part name
Qty
1
2
Screw (3x10)
1
5
Thermal head unit
1
3
CIS unit
1
3 CIS unit
Screwdriver
2
Hook
4
Hook
Hook
(200 g)
(400 g)
5 Thermal head unit
(700 g)
(800 g)
(700 g)
(200 g)
(400 g)
1
Fig. 3
3–5
Mechanism unit
UX-P115U
4
Wire treatment
Parts list (Fig. 4)
No.
Part name
Qty
1
Screw (4x6)
1
2
Band (100mm)
2
Bottom plate
AC cord earth cable
AC cord
1
Figure for setting the
Speaker Hold Spring
Wire holder PWB
TEL/LIU
PWB
Power supply PWB
Head cable
Drive unit
Panel cable
Speaker
Speaker
Motor cable
Cam switch cable
Speaker cable
Control PWB
Speaker
Hold
Spring
CIS cable
Rib
Drive unit
Rib Motor cable
Cam
switch
cable
Operation panel unit
Top cover unit
2
Panel cable
Thermal head
CIS cable
Head cable
Scanner
frame
Panel cable
Rib
Rib
Head cable
Tape
Rib
2
Tape
Wire hold PWB
Rib
Fig. 4
3–6
4–1
LINE
HANDSET
SPEAKER
AMPLIFIER
SURGE
PROTECT/
FILTER
CNPRG
CONTROL PWB UNIT
CML
CI
AMPLIFIER
FLASH
2Mbit
TEL/LIU
PWB UNIT
CLOCK
32.768kHz
TRANSFORMER
CLOCK
32.256MHz
VBT
DRAM
4Mbit
PIO
DSP
IA(CX20438)
CPU
RTC
S-RAM(32kbit)
+3.3V
SURGE
TRANS
ABSORBER
RECTIFIER
DIODE
TRANSFORMER
RECTIFIER
+24V
FILM
SENSOR
THERMAL
HEAD
FILTER
POWER SUPPLY
PWB UNIT
LCD
PM
MOTOR
IMAGING
FILM
P-IN
SENSOR
RECORDING PAPER
DRIVER
CONTACT
IMAGE
SENSOR
DOCUMENT
SENSOR
FRONT
SENSOR
OPERATION
PANEL
FET
STABILIZER
REGULATOR
PANEL I/F
WATCHDOG
TIMER
SIO
THERMAL
HEAD I/F
SENSOR I/F
MOTOR I/F
CIS I/F
TIMER
SIO
INTERRUPT
CONTROLLER
CPU I/F
1CHIP FAX ENGINE (SCE209)
UX-P115U
UX-P115U
FAX
Service
E
Market
Manual 4. DIADRAMS
CHAPTER
[1] Block diagram
4–2
CNLCD
OPERATION
PANEL PWB
NUIT
14
LCD UNIT
CNPN-A
CONTACT IMAGE SENSOR
THERMAL HEAD
7
15
16
CNCIS
CNTH
TX/RX MOTOR
CNPN
CNMT
6
CNPRG
SPEAKER
3
CNSP
CONTROL PWB UNIT
CNCSW
2
CAM SW
CNPW
CNLIUA
6
12
MJ1
POWER SUPPLY
PWB UNIT
CNPS
CNLIUA
TEL/LIU
PWB UNIT
MJTEL
4
TEL LINE
HANDSET
AC CORD
UX-P115U
[2] Wiring diagram
UX-P115U
[3] Point-to-point diagram
CNMT
TX/RX
MOTOR
TPBDTPADTPBD
TPAD
VMT
VMT
1
2
3
4
5
6
THERMAL
HEAD
VTH
VTH
STRB1STRB2THI
RANK
THG
THG
THG
THVDD
STRB3STRB4LATCHPCLK
DATA
VTH
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
OPERATION
PANEL
PWB
CIS
CNPN-A
KEN4A
1
KEN3A
2
KEN2A
3
KEN1A
4
DG
5
+3.3V
6
ORGSNS- 7
FRSNS8
E
9
SEN0
10
SEN1
11
SEN2
12
SEN3
13
SEN4
14
SEN5
15
SEN6
16
VO
VG
CISVDD
øT
CISCLK
GLED
+24V
1
2
3
4
5
6
7
1
2
3
4
5
6
CNLIUA
1
RHS2
MAG
3
+24VL
MICMUTE 4
5
TELIN
TELMUTE 6
7
RXIN
8
TXOUT
9
CML
10
PIN
11
FILM
12
CI-
TPBDTPADTPBD
TPAD
VMT
VMT
CNTH
VTH
1
STRB12
STRB23
THI
4
RANK
5
THG
6
THG
7
THG
8
THVDD
9
10 STRB311 STRB412 LATCHPCLK
13
DATA
14
VTH
15
CNLIUA
RHS1
DG
2
+24VL
3
4 MICMUTE
TELIN
5
6 TELMUTE TEL/LIU
PWB
7
RXIN
8
TXOUT
9
CML
10
PIN
11
FILM
12
CI-
CNPRG
FLTXD
1
DG
2
FLRXD
3
CNPN
1
KEN4A
2
KEN3A
3
KEN2A
4
KEN1A
5
DG
6
+3.3V
7 ORGSNS8
FRSNS9
E
10
SEN0
11
SEN1
12
SEN2
13
SEN3
14
SEN4
15
SEN5
16
SEN6
CNPW
1
+24V
2
+24V
3
MG
4
MG
5
DG
6
+5V
CNCSW
1
CSW2
DG
1
2
CSWDG
CNSP
1
2
3
1
2
3
SP+
N.C.
SP-
SP+
N.C.
SP-
CNCIS
1
VO
2
VG
3
CISVDD
4
øT
5
CISCLK
6
GLED
7
+24V
CONTROL
PWB
4–3
CNPS
+24V
1
+24V
2
POWER
MG
3
SUPPLY
MG
4
PWB
DG
5
6 VREG(+5V)
CAM
SWITCH
SPEAKER
UX-P115U
UX-P115U
FAX
Service
E
Market
Manual 5. CIRCUIT DESCRIPTION
CHAPTER
[1] Circuit description
1. General description
3. Operational description
The compact design of the control PWB is obtained by using CONEXANT fax engine in the main control section and high density printing of
surface mounting parts. Each PWB is independent according to its
function as shown in Fig. 1.
Operational descriptions are given below:
•
When a document is loaded in stand-by mode, the state of the document sensor is sensed via the 1 chip fax engine (SCE209). With
depression of the START key in the off-hook state, transmission
takes place. Then, the procedure is sent out from the modem and
the motor is rotated to move the document down to the scan line. In
the scan processor, the signal scanned by the CIS is sent to the
internal image processor and the AD converter to convert the analog signal into binary data. This binary data is transferred from the
scan processor to the image buffer within the RAM and encoded
and stored in the transmit buffer of the RAM. The data is then converted from parallel to serial form by the modem where the serial
data is modulated and sent onto the line.
2. PWB configuration
MOTOR
TEL/LIU
PWB
CIS
LCD
PWB
CONTROL
PWB
•
POWER
SUPPLY
PWB
PANEL
PWB
Transmission operation
Receive operation
There are two ways of starting reception, manual and automatic.
Depression of the START key in the off-hook mode in the case of
manual receive mode, or CI signal detection by the LIU in the automatic receive mode. First, the SCE209 controls the procedure signals from the modem to be ready to receive data. When the
program goes into phase C, the serial data from the modem is converted to parallel form in the modem interface of the 1 chip fax
engine (SCE209) which is stored in the receive buffer of the RAM.
The data in the receive buffer is decoded software-wise to reproduce it as binary image data in the image buffer. The data is DMA
transferred to the recording processor within the SCE209 which is
then converted from parallel to serial form to be sent to the thermal
head. The data is printed line by line by the SCE209 which is
assigned to control the motor rotation and strobe signal.
AC CORD
Fig. 1
2.1. Control PWB
The control PWB controls peripheral PWBs, mechanical parts, transmission, and performs overall control of the unit.
This machine employs a 1-chip modem (SCE209) which is installed on
the control PWB.
•
2.2. TEL/LIU PWB
Copy operation
To make a copy on this facsimile, the COPY key is pressed when
the machine is in stand-by with a document on the document table
and the telephone set is in the on-hook state. First, depression of
the COPY key advances the document to the scan line. Similar to
the transmitting operation, the image signal from the CIS is converted to a binary signal in the DMA mode via the 1 chip fax engine
(SCE209) which is then sent to the image buffer of the RAM. Next,
the data is transferred to the recording processor in the DMA mode
to send the image data to the thermal head which is printed line by
line. The copying takes place as the operation is repeated.
This PWB controls connection of the telephone line to the unit.
2.3. Power supply PWB
This PWB provides voltages of Vreg(+5V) and +24V to the other
PWBs.
2.4. Panel PWB
The panel PWB allows input of the operation keys.
2.5. LCD PWB
This PWB controls the LCD display.
5–1
UX-P115U
[2] Circuit description of control PWB
1. General description
2.2.4 External RAM and ROM
Fig. 2 shows the functional blocks of the control PWB, which is composed of 3 blocks.
Moveable and programmable size external SRAM memory of up to 1
MB, DRAM memory of up to 4 MB, and ROM of up to 2 MB can be
directly connected to the SCE209. By using an external address
decoder, the size of SRAM and/or ROM can be extended. The ROM
stores all the program object code.
(1) SCE209
IA(CX20438)
MEMORY(SRAM)
(2) FLASH
2.2.5 Flash Memory Controller
The SCE209 includes a flash memory controller that supports NOR,
NAND, and Serial NAND-type flash memory. The supported size of
NOR-type memory is up to 1 MB and the supported size of NAND-type
memory is unlimited.
(3) DRAM
Fig. 2 Control PWB function block diagram
2.2.6 Stepper Motor Control
2. Description of each block
Devices are connected to the bus to control the whole unit.
Eight outputs are provided to external current drivers: four to the scanner motor and four to the printer motor. The stepping patterns are programmable and selectable line times are supported. A timeout circuit
controls the power control of the motors. The printer or scanner motor
outputs can be programmed as GPOs for applications using single
motor or paper printers.
2.1.1 SCE209 (IC3): pin-176 QFP (FAX CONTROLLER)
2.2.7 T.4/T.6 Compression/Decompression
1 chip fax engine has Internal Integrated Analog (20438) and Internal
memory (SRAM: 32kbit).
FLASH of 2Mbit equipped with software for the main CPU.
MH, MR and MMR compression and decompression are provided in
hardware. T.4 line lengths of up to 8192 pixels are supported. MMR
and Alternating Compression/Decompression (ACD) on a line by line
basis provide support for up to three independent compression and
decompression processes.
2.1.3 IS41LV85125 (IC2): pin-28 SOJ (DRAM)
2.2.8 Bi-level Resolution Conversion
Image memory for recording process.
One independent programmable bi-level 1D-resolution conversion
block is provided to perform expansion or reduction on the T.4 decompressed data and scan image data. Image expansion can be programmed up to 200% and reduction down to 33%. Vertical line O-Ring
and data output bit order reversal is also provided.
2.1. Main control block
The main control block is composed of CONEXANT 1 chip fax engine
(SCE209), FLASH (2Mbit), DRAM (4Mbit).
2.1.2 SST39VF020P (IC1): pin-32 TSOP (FLASH)
Memory for recording pixel data without paper.
2.2. IC3 (SCE209) Hardware description
2.2.1 Integrated Controller (SCC)
2.2.9 Printer IF
The Controller contains an internal MC24 Processor with a 16-MB
address space and dedicated circuitry optimized for facsimile image
processing and monitoring and for thermal or thermal transfer printer
support.
The Printer Interface provides a standard connection between the
SCE209 and a thermal printhead to support thermal printing or thermal
transfer. The thermal printer interface consists of programmable data,
latch, clock, and up to four strobe signals. Programmable timing supports traditional thermal printers, as well as the latchless split mode
printers, and line lengths of up to 2048 pixels. Line times from 5 ms to
40 ms are supported.
The CPU provides fast instruction (up to 10 MHz clock speed) execution and memory efficient input/output bit manipulation. The CPU connects to other internal functions over an 8-bit data bus and 24-bit
address bus and dedicated control lines.
The 24-bit external address bus, 8-bit data bus, control, status and
decoded chip select signals support connection to external ROM,
SRAM, DRAM, and FLASH memory.
The SCE209 includes a thermal ADC (TADC) function utilizing a D/A
converter and a comparator to monitor the printhead temperature.
External terminating resistors must be supplied; the values are determined by the specific printhead selected.
2.2.2 DRAM Controller
As an option, plain paper inkjet printing can be supported.
The CX06835 includes a DRAM controller with signal and page mode
access support which supports fast, normal, or slow refresh time.
DRAM memory space is provided in one block up to 4 MB. A maximum of 4 MB of DRAM is supported. This space has a programmable
size and starting address. Refresh is performed automatically and is
supported in stand-by mode. CAS and RAS signal support is provided
for one-DRAM banks for both 4-bit and 8-bit organizations. Access
speeds from 50ns to 70ns can be supported.
2.2.10 TPH Hardware Timer
The TPH hardware timer provides a 500 ms timer that can be re-triggered or reset.
2.2.11 Scanner and Video Control
Five programmable control and timing signals support common CCD
and CIS scanners. The video control function provides signals for controlling the scanner and for processing its video output. Three programmable control signals (START, CLK1n, and CLK2) provide timing
related to line and pixel timing. These are programmable with regard
to start time, relative delay and pulse width.
2.2.3 DMA Channels
Six internal DMA channels support memory access for scanner, T.4/
T.6, and resolution conversion. DMA Channel 2 can be reprogrammed
for external access to thermal printing, thermal transfer, or plain paper
inkjet printing.
Two video control output signals (VIDCTL[1:0]) provide digital control
for external signal pre-processing circuitry. These signals provide a per
pixel period, or per line period, timing with programmable polarity control for each signal.
5–2
UX-P115U
2.2.12 Video Processing
2.2.19 Reset and Power Control
The CX06835 supports two modes of shading correction for scanner
data non-uniformity arising from uneven sensor output or uneven illumination. Corrections are provided on either an 8-pixel group or are
applied separately to each pixel. Dark level correction and gamma correction are also provided.
The RESETn I/O pin provides an internally generated reset output to
external circuits, or it can accept an externally generated reset signal.
This reset signal will not reset the RTC. Separate RTC battery power
inputs are provided for battery-backup functions. A BATRSTn pin is
provided, which resets the RTC circuits and other SCC circuits.
Two-dimensional Error Diffusion/Dithering is performed on halftone
images.
2.2.20 Power Up/Down Control
Power Up/Down detection is provided internally. The threshold voltages are:
The CX06835 includes an 8 x 8 dither table, which is programmable
and stored internally (8-bit per table entry). The table is arranged in a
matrix of 8 rows by 8 columns. The video processing circuit provides
mixed-mode detection/processing and multi-level Resolution Conversion for the scanner multi-level data. The conversion ratio of the multilevel Resolution Conversion is fixed to B4-A4 conversion.
•
An internally generated power down signal controls internal switching
between primary and battery power. This control signal is also provided as an output on the PWRDWNn pin. An externally generated
power down detector (optional) can be provided as an input on the
PWRDWNn pin by setting the INTPWRDWNEn pin.
2.2.13 Operator Panel Interface
Operation Panel functions are supported by the operator output bus
OPO[6:0], the operator input bus OP[3:0], and two control outputs
(LCDCS and LEDCTRL).
2.2.21 Stand-by and Sleep Modes
Two power saving modes are provided to reduce the power consumption. In stand-by mode, the CPU is functional, but the modem clock is
turned off to save power. When this occurs, the modem may be activated by software under different conditions. In sleep mode, the clock
is cut off from both the modem and the CPU to increase the power
savings.
The CX06835 can directly interface to a 28-key keypad.
A 2-line LCD display module with 20 characters per line can be supported.
2.2.14 Synchronous Serial Interface (SSIF)
The system can be activated by paper insertion, key pressing events,
and telephone ring detection.
One or optionally two Synchronous only Serial Interfaces (SSIF) are
built into the CX06835, which allows it to communicate with external
peripherals. Each SSIF provides separate signals for Data (SSTXD,
SSRXD), Clock (SSCLK), and Status (SSSTAT). Each SSIF is a
duplex, three-wire system. The SSIF may be configured to operate as
either a master or a slave interface. The bit rate, clock polarity, clock
phase, and data shifting order are programmable.
2.2.15 Synchronous/Asynchronous
(SASIF)
Serial
2.2.22 Embedded Modem DSP
The embedded modem DSP is a synchronous 9600 bps half-duplex
modem with error detection and DTMF generation/reception. It provides data transmission/reception from regular PSTN lines, PBX, or
private lines.
Interface
The modem can operate at any standard V.29 data speed up to 9600
bps as well as in V.21 and V.23 modes.
One or optionally two Synchronous/Asynchronous Serial Interface
(SASIF) performs the following:
•
Serial-parallel conversion of data received from a peripheral
device.
•
Parallel-to-serial conversion of data for transmission to a peripheral
device.
Power Up detection level = 2.83V to 2.95V.
The modem is designed for use in Group 3 facsimile machines. It satisfies the requirements specified in ITU-T recommendations V.29,
V.27ter, V.21 Channel 2, and T.4 , and meets the signaling requirements of T.30. It also performs HDLC framing according to T.30 at all
speeds.
NOTE: For technical details, refer to the FM209/FM214 Designer’s
Guide, (document 1175).
This interface consists of serial transmit data (SASTXD), serial receive
data (SASRXD), and a serial clock (SASCLK). The SASIF includes a
programmable bit rate generator for asynchronous and synchronous
operations. The data shifting order, data bit number, and the SASCLK
polarity are programmable.
2.2.23 Software and Firmware Support Features
Available software and embedded firmware provides the following:
•
Modem support for speeds up to 9600 bps.
The optional SASIF 2 has an additional pin called DSS_AVAIL. This
signal can be used to tristate the SASCLK2 and SASTXD2 signals.
•
ECM under conditional assembly.
•
DRAM memory support under conditional assembly.
2.2.16 Real Time Clock (RTC)
•
MH, MR and MMR support.
The CX06835 includes a battery backup real time clock. The RTC will
automatically maintain the proper date and time for 32 years. Leap
year compensation is included. A 32.768 kHz or 65.536 kHz crystal is
required by the RTC.
•
Page memory receiving.
•
5 ms minimum scan line time.
•
Conditional Error Diffusion or Dither table (8x8) support.
2.2.17 Tone Generator (ALT_TONE)
The CX06835 provides a programmable tone generator output. The
frequency of the tone generator is programmable from 400 Hz to 4
kHz. By using a PWM programmable high frequency as a modulation
frequency, the output level can be made programmable.
2.2.18 Watchdog Timer
The Programmable Watchdog Timer is intended to guard against firmware lockup on the part of either executive-controlled background
tasks or interrupt-driven tasks, and can only be enabled by a sequence
of events under control of the Watchdog Control Logic. Once the
Watchdog Timer has been enabled, it can not be disabled unless a
system reset occurs.
5–3
•
Dark Level Correction support.
•
Single motor support.
•
28-key operator panel support.
•
Call progress support for Europe and U.S.A.
•
Monochrome inkjet print engine support.
UX-P115U
SCE209 (IC3) Terminal descriptions
Pin
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
Pin List
I/O
VDDPLL
VSSPLL
ROMCSn
SYNC/GPO[20]
WRn
RDn
DEBUGn
TSTCLK
VSS
SXIN
SXOUT
OPO[0]/GPO[8]/SMPWRCTRL
OPO[1]/GPO[9]/PMPWRCTRL
OPO[2]/GPO[10]/RINGER
OPO[3]/GPO[11]
OPO[4]/GPO[12]/SSTXD1
OPO[5]/GPO[13]
OPO[6]/GPO[14]
OPI[0]/GPIO[21]/SSRXD1
OPI[1]/GPIO[22]/SSSTAT1
OPI[2]/GPIO[23]/SSCLK1
OPI[3]/GPIO[24]
LCDCS/GPO[17]
VDD
RASn
CAS[0]n
DWRn
VBAT
XIN
XOUT
WRPROTn
TEST[1]
TEST[0]
BATRTSn
INTPWRDWNEn
PWRDWNn
N.C.
ADGA
VREFn/CLREF
VIN
ADGA
ADVA
ADXG
VREFp
VSS
IVREFn
IVREFp
VDD
THADI
VSS
GPIO[17]/DSPIRQn
GPIO[16]/IRQ[8]
GPIO[15]/CS[5]n
GPIO[13]/CS[3]n
GPIO[37]/IRQ15n/DSPCSn
GPIO[4]/CPCIN/TPHPWRCTRL/DMAREG
STRB[0]
STRB[1]
STRB[2]
STRB[3]
PLAT
PDAT
—
—
—
O
O
O
I
O
—
I
O
O
O
OZ
O
O
O
O
I/O
I/O
I/O
I/O
O
—
O
O
O
—
I
O
O
I
I
I
I
I/O
—
—
I
I
—
—
—
I
—
O
O
—
I
—
I/O
I/O
I/O
I/O
I
I/O
O
O
O
O
O
O
Input
Type
—
—
—
—
—
—
Hu
—
—
Osc0
—
—
—
—
—
—
—
—
Hu
Hu
Hu
Hu
—
—
—
—
—
—
Osc1
—
—
Hd
Hd
H
H
H
—
VADG
VRVA
VADG
VADV
VXG
VR
—
—
—
—
Analog
—
Hu
Hu
Hu
Hu
Hu
Hu
—
—
—
—
—
—
5–4
Output
Type
—
—
13Xs
13Xs
13Xs
13Xs
—
13Xs
—
—
Osc0
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
1XC
—
13Xs
13Xs
13Xs
—
—
Osc1
1XC
—
—
—
—
13Xs
—
—
—
—
—
—
—
—
—
VRVR+
—
—
—
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
1XC
1XC
1XC
1XC
3XC
2XC
Pin Description
PLL Power
PLL GND
—
—
—
—
—
—
Digital GND
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Digital Power
—
—
—
RTC Battery Power
—
—
—
—
—
—
—
—
—
PADC Analog GND
PADC
PADC
PADC Analog GND
PADC Analog Power
PADC
PADC
VSS Digital GND
PADC
PADC
Digital Power
TADC
Digital GND
—
—
—
—
—
—
—
—
—
—
—
—
UX-P115U
SCE209 (IC3) Terminal descriptions
Pin
No.
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
Pin List
PCLK/DMAACK
VDD
GPIO[11]/BE/SERINP/SR4IN
GPIO[19]/RDY/SEROUT
START
CLK1n/GPO[25]
CLK2/GPO[24]
GND
MCLK
CTRLI
TESTC
SOUT
SIN
FSYNC
POR
GND
LINE_INP
MIC_INP
MIC_INM
MIC_BIAS
BG
VC
AVDD
GND
LINE_OUTP
SPKR_OUTP
SPKR_OUTM
DVDD
MODE_0
ICLK
VSS
FCSn[1]/VIDCTL[0]/GPO[23]
IARESET
IACLK
VDD
IA1CLK
SR3IN/DSPIRQn
SR4OUT
SR1IO
SA1CLK
GPIO[7]/SSRXD2/SASRXD2
GPIO[6]/SSTXD2/SASTXD2
GPIO[5]/SSCLK2/SASCLK2
GPIO[10]/SSSTAT2/DSS_AVAIL
VSS
RESETn
GPIO[3]/SASCLK
GPIO[2]/SASRXD
GPIO[1]/SASTXD
GPIO[9]/FRDn
GPIO[8]/FWRn
A[0]
A[1]
A[2]
A[3]
A[4]
VDD
A[5]
A[6]
A[7]
A[8]
A[9]
I/O
O
—
I/O
I/O
O
O
O
—
ID
ID
ID
OD
ID
I/OD
IA
—
IA
IA
IA
OA
OA
OA
PWR
—
OA
OA
OA
PWD
ID
I/OD
—
O
O
O
—
I
I
O
O
I
I/O
I/O
I/O
I/O
—
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
—
I/O
I/O
I/O
I/O
I/O
Input
Type
—
—
Hu
Hu
—
—
—
—
—
d
d
—
d
d
d
—
—
—
—
—
—
—
—
—
—
—
—
—
u
—
—
—
—
—
—
H
H
—
—
H
Hu
Hu
Hu
Hu
—
Hu
Hu
Hu
Hu
Hu
Hu
Tu
Tu
Tu
Tu
Tu
—
Tu
Tu
Tu
Tu
Tu
5–5
Output
Type
3XC
—
13Xs
13Xs
2XC
13Xs
13Xs
—
—
—
—
T
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
13Xs
13Xs
13Xs
—
—
—
13Xs
13Xs
—
13Xs
13Xs
13Xs
13Xs
—
2XC
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
—
13Xs
13Xs
13Xs
13Xs
13Xs
Pin Description
—
Digital Power
—
—
—
—
—
IA GND
Main Clock from DSP
Control Data from DSP
IA Test
Serial Data to DSP
Serial Data to DSP
Frame Sync Signal (IA)
Hardware Reset
IA GND
Analog Input to Line Pre-Amp.
Positive differential Analog Input to Microphone Pre-Amp.
Negative differential Analog Input to Microphone Pre-Amp.
2.2 V Nominal DC Bias Source for Electret Microphone
Analog reference Voltage Output
Analog Ground Bias Output
IA Analog Power
IA GND
Line Driver Output
Positive Speaker Driver Output
Negative Speaker Driver Output
IA Digital Power
Connect to VSS (IA Mode Selection)
IA Bit Clock Input/Output
VSS Digital GND
—
DSP to EXTIA POR
DSP to EXTIA MCLK
Digital Power
DSP from EXTIA ICLK
DSP from primary EXTIA SOUT/EXT. Modem IRQn
DSP to primary EXTIA SIN
DSP to EXTIA CTRL1
DSP from EXTIA FSYNC
—
—
—
—
Digital GND
—
—
—
—
—
—
CPU Address Bus
CPU Address Bus
CPU Address Bus
CPU Address Bus
CPU Address Bus
Digital power
CPU Address Bus
CPU Address Bus
CPU Address Bus
CPU Address Bus
CPU Address Bus
UX-P115U
SCE209 (IC3) Terminal descriptions
Pin
No.
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
Pin List
A[10]
A[11]
A[12]
A[13]
A[14]
A[15]
A[16]
VDD
VSS
A[17]
A[18]
A[19]
A[20]
A[21]/EYECLK
A[22]/EYESYNC
A[23]/EYEXY
D[0]
D[1]
D[2]
D[3]
D[4]
D[5]
D[6]
D[7]
GPIO[20]/ALTTONE
GPIO[26]
GPIO[27]
GPIO[28]
GPO[26]
GPO[27]
GPO[28]
GPO[29]
GPO[30]/SR3OUT
GPIO[29]
GPIO[31]
GPIO[32]
VDD
GPIO[34]
GPIO[35]
GPIO[36]
Vss
VDD
PM[0]/GPO[0]
PM[1]/GPO[1]
PM[2]/GPO[2]
PM[3]/GPO[3]
SM[0]/GPO[4]
SM[1]/GPO[5]
SM[2]/GPO[6]
SM[3]/GPO[7]
REGDMA/GPO[18]/CLKDIV[0]
WAITn/GPO[19]/CLKDIV[1]
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
—
—
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
O
O
O
O
I/O
I/O
I/O
—
I/O
I/O
I/O
—
—
O
O
O
O
O
O
O
O
I/O
I/O
Input
Type
Tu
Tu
Tu
Tu
Tu
Tu
Tu
—
—
Tu
Tu
Tu
Tu
Tu
Tu
Tu
Tu
Tu
Tu
Tu
Tu
Tu
Tu
Tu
Hu
Hu
Hu
Hu
—
—
—
—
—
Hu
Hu
Hu
—
Hu
Hu
Hu
—
—
—
—
—
—
—
—
—
—
T
T
5–6
Output
Type
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
—
—
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
—
13Xs
13Xs
13Xs
—
—
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
Pin Description
CPU Address Bus
CPU Address Bus
CPU Address Bus
CPU Address Bus
CPU Address Bus
CPU Address Bus
CPU Address Bus
Digital Power
Digital GND
CPU Address Bus
CPU Address Bus
CPU Address Bus
CPU Address Bus
CPU Address Bus
CPU Address Bus
CPU Address Bus
CPU Data Bus
CPU Data Bus
CPU Data Bus
CPU Data Bus
CPU Data Bus
CPU Data Bus
CPU Data Bus
CPU Data Bus
—
—
—
—
—
—
—
—
—
—
—
—
Digital power
—
—
—
Digital GND
Digital Power
—
—
—
—
—
—
—
—
—
—
UX-P115U
2.3. Panel control block
The following controls are performed by the SCE209.
•
Operation panel key scanning
•
Operation panel LCD display
2.4. Mechanism/recording control block
•
Recording control block diagram (1)
OPERATOR
PANEL,
KEYPAD,
LEDS & LCD
PRINTER DATA
CONTROL &
SENSORS
OPO[7:0]*
OPI[3:0]*
LEDCTL*
LCDCS*
STRB[3:0]
STRBPOL
THADI
PDAT
PCLK
PLAT
TEST[1:0]
BATRSTN
RESETN
TONE
ALTTONE
TSTCLK
REGDMA
WAITN
SYNC
PWRDWNN
INTPWRDWNEN
XIN
XOUT
RTC
CRYSTAL
SXIN
SXOUT
SYSCLK
CRYSTAL
TELEPHONE
LINE
PRINTER &
SCANNER
MOTOR DRIVERS
SCANNER
CONTROLS &
SENSORS
SCANNER
VIDEO
PREPROCESSING
SERIAL SYNC
PORTS
(SSIF)
GENERAL
PURPOSE I/O
SYNC/ASYNC
SERIAL PORT
SASIF
PM[3:0]*
SM[3:0]*
START
CLK2
CLK1
CLK1N
VIDCTL[1:0]
VIN
VREFP
VREFN
IVREFP
IVREFN
SSCLK[2:1]*
SSTXD[2:1]*
SSRXD[2:1]*
SSSTAT[2:1]*
GPIO
SASCLK*
SASTXD*
SASRXD*
INTERNAL
IA
SCE209
1-CHIP
FAX ENGINE
A[23:0]
D[7:0]
RDN
WRN
ROMCSN
CS[5:0]N*
WRPROTN
FRDN*
FRWN*
FCLE*
FCSN[2:0]
DEBUGN
VDD
VDRAM
VBAT
VSS
ADVA
ADGA
Fig. 3
5–7
RXIN
TXOUT
LINE
INTERFACE
EXTERNAL BUS
RDN, ROMCSN
FLASH
MEMORY
CAS[0,1]N, RASN, DWRN
CS3N,
CS4N**
D7[7:0]
DRAM
FLASH MEMORY
(OPTION)
NOTES: * ALTERNATIVE GPO, GPI OR GPIO LINES
**FOR SAMSUNG NAND-TYPE FLASH
UX-P115U
2.5. Modem block (CX20438)
Integrated Analog Control Resisters for CX20438
The CX20438 IA can be used as a Primary Integrated Analog (PIA) codec or as a Secondary Integrated Analog (SIA) codec, depending on the signal
connection with the SCE Controller ASIC device. In the SCE100 product, both the PIA and the SIA are packaged external to the SCE Controller
device, whereas in the SCE209, the PIA is packaged with the SCE209 Controller and the SIA is external.
The CX20438 IA provides gain, filtering, internal analog switching, and an internally sourced microphone bias output. The IA is controlled by three
control registers and an address register located in internal RAM space which are accessed via the modem interface memory. These registers provide individual controls for the IA’s inputs, outputs, gain settings, and switching.
The registers are located in internal DSP RAM. Each bit of each 8-bit IA control register has exactly the same meaning for the PIA and the SIA. The
LSB of each 16-bit address contents is used to control the PIA. The MSB of each 16-bit address contents is used to control the SIA.
The following table the PIA/SIA control register RAM access code.
Register
SBRAMx
BRx
Crx
IACR1
0
0
0
IACR2
0
0
0
IACR3
0
0
0
IAADD
0
0
0
NOTES: *Registers to use when x=1. When x=2, add 10h.
IOx
0
0
0
0
AREXx
0
0
0
0
•
For changes made to IACR1 to be effective, the host must write to IAADD with a value of 0002h.
•
For changes made to IACR2 to be effective, the host must write to IAADD with a value of 0006h.
•
For changes made to IACR3 to be effective, the host must write to IAADD with a value of 0007h.
ADDx
D0
D4
D5
CE
PIA Reg*
0
0
0
0, 1
Configuration default values are shown below.
DEFAULT VALUE
CONFIGURATION
V.17/V/33
V.29
V.27ter
V.21 Ch. 2
V.23/Caller ID
Tone Transmit/Detect
Voice/Audio Codec
Speakerphone
IACR1
1D9Eh
1D9Eh
1D9Eh
1D9Eh
1D9Eh
1D9Eh
0D16h
0D16h
IACR2
0008h
0008h
0008h
0008h
0008h
0008h
0008h
0008h
IACR3
0000h
0000h
0000h
0000h
0000h
0000h
0000h
0000h
The following signal flow block diagram is for a signal IA and it applies to both PIA and SIA.
LINE IN ENABLE MIC ENABLE
MICM
LINEIN
MIC/LINE SELECT
MICP
GAIN
LPF
ADC
0, 20, 25, 30 dB(MIC IN)
0dB(LINE IN)
SOUT
0, +4 dB
LINE OUT ENABLE
(1,0)
(1,1)
LINE OUT
LINE
DRIVER
LINE IN
SELECT
(0,0)
Mute, 0, -6, -12 dB
SPKRP
SPKRM
SPEAKER
DRIVER
RT
Loop
(0,0)
DAC
(1,0)
(0,1)
0, 6 dB
SPEAKER OUT ENABLE
(1,1)
Fig. 4 PIA/SIA Signal Flow Control
5–8
SIN
SIA Reg*
1
1
1
0, 1
UX-P115U
[3] Circuit description of TEL/LIU PWB
1. TEL/LIU block operational description
1.1. Block diagram
TEL/LIU PWB
CONTROL PWB
RTLOOP
IC100
LINE
H
SIGTX
SPKRP
SIGRX
MICP
0,1
0,0
1,0
1,1
TXOUT
L
CML
SP OUT
CI DETECTOR
RXIN
PC1
LINEIN
IC100
MIC ENABLE
IC100
TEL IN
TEL MUTE
(H:MUTE)
TX
HANDASET
MIC MUTE
(H:MUTE)
LPF
0,20,25,30dB
MODEM BLOCK
(CX20438 I/A)
RX
SIN
DAC
ENABLE
MIC
/LINE
SELECT
LINE IN ENABLE
Q102
0,6dB
ADC
LINE OUT ENABLE
LINE
SELECT
1,1
0,0
1,0
SPOUT
IC100
LINE
OUT
Q103
0,+4dB
SOUT
IC4
MUTE,0,-6,-12dB
SPEAKER SP MUTE
(H:MUTE)
DTMFMUTE
RCVOL
SP MUTE
TEL MUTE
CI
CML
MIC MUTE
IC3 SCE209
FAX CONTROLLER
+24VL
DG
Fig. 5
1.2. Circuit description
1.3. Block description
The TEL/LIU PWB is composed of the following 6 blocks.
1. Speech circuit section
1. Speech circuit section
•
2. Dial transmission section
The receiver volume is an electronic volume type, this model is
switched in 3 steps.
2. Dial transmission section
3. Speaker amplifier section
4. Ringer circuit section
5. CI detection circuit
6. Signal/DTMF transmission level & receiving level
•
D.P. transmission: The CML relay is turned on and off for control in
the DP calling system. (Refer to the attached sheet.)
•
DTMF transmission: It is formed in the modem, and is output.
3. Speaker amplifier section
•
Ringer volume: It is controlled by the combination of the attenuator
value of the LINE DRIVER in the modem and the ringer sending
level sent from the modem.
•
Speaker volume: It is controlled by the attenuator value of the LINE
DRIVER in the modem.
4. Ringer circuit section
•
5–9
The ringer sound is formed in the tone of modem when CI signal is
detected. The amplifier circuit drives the speaker of the main body.
UX-P115U
5. CI detection circuit
1.4. Signal selection
•
The following signals are used to control the transmission line of TEL/
FAX signal. For details, refer to the signal selector matrix table.
CI is detected by the photo coupler which is integrated in series in
the primary side TEL circuit well proven in the existing unit.
6. Signal/DTMF transmission level & receiving level
[Control signals from output port]
•
Signal transmission level setting: ATT -8 dB Circuit output: -11
dBm.
•
DTMF transmission level setting: HF -2.5 dBm
Thus, set the level.
Signal Name
CML
(The circuit is
located in the
TEL/LIU PWB.)
SP MUTE
(The circuit is
located in the
TEL/LIU PWB.)
TELMUTE
LF -4.5 dBm
RCVOL
DTMFMUTE
(The circuit is
located in the
control PWB.)
Description
Line connecting relay and DP generating relay
H: Line make
L: Line break
Speaker tone mute control signal
H: Muting (Power down mode)
L: Muting cancel (Normal operation)
Handset reception mute control signal
H: Muting
L: Muting cancel
Handset receiver volume control signal
Volume
High Middle
RCVOL
DTMFMUTE
L
L
Low DTMF sending
H
L
H
H
H
H
Note: The DTMF sending listed above is DTMF
signal sending in the handset OFF-HOOK mode.
VOLUME SETTING
Receiver volume
setting
DTMF Transmission volume setting
(Receiver)
Key buzzer volume
setting
Speaker volume
setting
Ringer volume setting
DTMF speaker volume setting
5 – 10
LINEOUT A
(HIGH) (LOW)
Low
High
Middle
Fixed
Low
Middle
High
Low
Middle
High
Low
Middle
High
1
1
0
1
1
0
1
1
0
1
0
1
1
0
1
1
0
1
RCVOL
DTMF
MUTE
1
0
1
1
1
0
0
1
UX-P115U
[Signals for status recognition according to input signals]
Signal Name
RHS
CI
Function
H: The handset is in the on-hook state.
L: The handset is in the off-hook state.
Incoming call (CI) detection signal
[Other signals]
Signal Name
TEL IN
SPOUT
TXOUT
RXIN
NO
1
2
3
4
5
6
Function
Receiving signal from line or modem
Speaker output signal
Transmission (DTMF) analog signal output
from modem
Reception (DTMF, others) analog signal input
into modem
Signal Name (CNLIUA)
RHSMAG
+24VL
MICMUTE
TELIN
TELMUTE
NO
7
8
9
10
11
12
Signal Name (CNLIUA)
RXIN
TXOUT
CML
PIN
FILM
CI-
(Example: SENDING/RECEIVING)
TEL/LIU PWB
CONTROL PWB
RTLOOP
IC100
LINE
H
SIGTX
SPKRP
SIGRX
MICP
0,1
0,0
1,0
1,1
TXOUT
L
CML
SP OUT
CI DETECTOR
RXIN
PC1
LINEIN
IC100
MIC ENABLE
Q102
IC100
TEL IN
TEL MUTE
(H:MUTE)
TX
HANDASET
MIC MUTE
(H:MUTE)
LPF
0,20,25,30dB
MODEM BLOCK
(CX20438 I/A)
RX
ADC
LINE OUT ENABLE
LINE
SELECT
1,1
0,0
1,0
SPOUT
IC100
LINE
OUT
Q103
IC4
MUTE,0,-6,-12dB
SPEAKER SP MUTE
(H:MUTE)
: FAX SENDING/RECEIVING
SIN
DAC
ENABLE
MIC
/LINE
SELECT
LINE IN ENABLE
0,6dB
DTMFMUTE
RCVOL
SP MUTE
TEL MUTE
CI
CML
MIC MUTE
+24VL
DG
5 – 11
IC3 SCE209
FAX CONTROLLER
0,+4dB
SOUT
UX-P115U
[4] Circuit description of power supply PWB
1. Block diagram
F1
3.15A/125V
AC IN
Noise
Filter
Circuit
Rectifying
Smoothing
Circuit
+24V
F3
4A/32V
Switching
Circuit
+5V
Control
Circuit
Photo Coupler
Fig. 7
2. Noise filter circuit
In this circuit, the DC voltage supplied from the rectifying/smoothing
section is converted into high Frequency pulses by ON/OFF repetition
of Q1.
The input noise filter section is composed of L1 and C1, which reduces
normal mode noise from the AC line and common mode noise to the
AC line.
5. Control circuit
This circuit controls output voltage of +24V by adjusting ON period of
Q1, looking at signal from photo coupler PC1.
3. Rectifying/smoothing circuit
In this operation PC1 takes charge of important part.
The AC input voltage is rectified by diode D1, 2, 3, 4 and smoothed by
capacitor C2 to supply DC voltage to the switching circuit section.
The over current protection is performed by bringing Q1 to OFF state
through detection of voltage of T1 subwinding.
4. SWitching circuit
The over voltage protection is performed by operating the over current
protection circuit through detection of Zener diode ZD4 and short-circuiting of load.
This circuit includes MOS FET Q1 and the gate drive circuit, and components around Q1.
[5] Circuit description of CIS unit
1. CIS
5ms
CIS is an image sensor which puts the original paper in close contact
with the full-size sensor for scanning, being a monochromatic type with
the pixel number of 1,728 dots and the main scanning density of 8
dots/mm.
Approx.3.3V
ΦT
0V
2µs
CISCLK
It is composed of sensor, rod lens, LED light source, light-conductive
plate, control circuit and so on, and the reading line and focus are previously adjusted as the unit.
VO
0.8V~2.9V
(White original paper)
Due to the full-size sensor, the focus distance is so short that the set is
changed from the light weight type to the compact type.
Fig. 8
2. Waveforms
The following clock is supplied from SCE209 of the control board, and
VO is output.
5 – 12
1
2
3
4
5
CNCIS-5
CNTH-12
CNTH-14
CNTH-13
CNTH-2
CNTH-3
CNTH-10
CNTH-11
CNCIS-4
A
DG
LATCH-
DATA
PCLK
STRB1-
STRB2-
STRB3-
<¿T>
STRB4-
¿T
<CISCLK>
CISCLK
DG
C184 C187 C169
C168 C185
C183 C186
N.M.
C124
DG
R111
R124
5
6
7
8
RA3
470
R147
150
270
B
R16
DG
32.256MHz
X1
1M
C106
N.M.
100
R174
R127
DG
N.M.
DG
C
60
59
58
57
63
62
61
67
69
C147
1u/10V
C162
1u/10V
DG
C161
1u/10V
STRB3
STRB2
STRB1
STRB0
PCLK
PDAT
PLAT
START
CLK2
SEN4
RA2
470
D
RA1
470
0.1u/25V
0.1u/25V
C137
0.1u/25V
C129
0.1u/25V
C112
0.1u/25V
C116
0.1u/25V
C119
0.1u/25V
C140
C141
0.1u/25V
C130
F
DG
E
N.M.
F
IC 3
SCE209(1/2)
FAX CONTROLLER
119
+3.3V
132
VDD
E
161
VDD
D
DG
DG
R142
9
VSS
C143
1u/10V
SXOUT
SXIN
TEST1
TEST0
100pFx5
C123
15p/50V
R130
300
11
10
32
33
+3.3V
C117
C115
C113
C118
C114
1000p/50Vx2
4
3
2
1
DG
N.M.
C122
33p/50V
DG
270 R160
0
270
N.M.
C125
C173
100pF/50Vx7
+3.3V
C
45
VSS
B
SEN0
50
VSS
6
C108
100p
42
ADVA
E
DG
DG
<L>
C144
1u/10V
DG
G
C149
C148
22p/50V 22p/50V
X2
10M
G
32.768kHz
<K>
7
<M>
8
DEBUGn
Main Control Block
R106
470
SEN6
CNPN-16
38,41
ADGA
CNPN-14
SEN3
CNPN-13
R105
470
43
ADXG
SEN2
CNPN-12
SEN5
CNPN-15
46
IVREFn
4
3
2
1
5
6
7
8
SEN1
CNPN-11
C107
100p
47
IVREFp
18
17
16
15
14
13
12
23
R104
470
CNPN-10
C189
C188
24
VDD
KEN3A
C158
48
VDD
0
R103
CNPN-9
KEN4A
CNPN-1
OPO6
OPO5
OPO4
OPO3
OPO2
OPO1
OPO0
LCDCS
97
64
CNPN-2
166
VDD
C102
C100
C101
VDD
OPI3
OPI2
OPI1
OPI0
22
21
20
19
4
3
2
1
5
6
7
8
KEN2A
CNPN-3
KEN1A
VDDPLL
1
C121
0.1u/25V
2
VSSPLL
SM3
SM2
SM1
SM0
174
173
172
171
(5-5F) TPB(5-5F) TPA(5-5F) TPB
(5-5F) TPA
VDD
CNPN-4
70
VSS
ALTTONE (BZ)
149
(6-2I) BZOUT1
XIN
29
VDD
C103
107
(5-2I) THADI
1u/10V C139
VSS
(5-6D) VIN
THADI
VIN
VREFn/CLREF
133
VREFp
+3.3V
49
40
39
VSS
44
165
VSS
XOUT
30
DG
108
RESET
INTPWRDOWNE
35
TSTCLK
PWRDWN
36
R141
DG
270
RAS
CAS
DWR
RD
WR
ROMCS
A3
A2
A1
A0
A7
A6
A5
A4
A11
A10
A9
A8
A15
A14
A13
A12
A23
A22
A21
A20
A19
A18
A17
A16
H
DG
C146
1u/10V
DG
DG
4
31
H
<J>
176 <I>
175 <H>
25
26
27
6
5
3
R125
N.M.
R162
DG
<BATRST>
DG
A3
A2
A1
A0
A7
A6
A5
A4
122
121
120
118
117
116
115
114
A11
A10
A9
A8
126
125
124
123
A18
A17
A16
A15
A14
A13
A12
10K
<A>
<B>
<C>
<D>
<E>
<F>
I
RAS- (2-4G)
CAS- (2-4G)
DWR- (2-4G)
RD- (2-3A)
W R- (2-4D)
ROMCS(2-4A)
A[18:0] (2-6A)
1/6
I
CNLiuA-17
D[7:0] (2-5A)
130
129
128
127
140
139
138
137
136
135
134
131
C142
1u/10V
C145 1u/10V
R139
220K
SYNC/GPO20
WRPROT
WAIT/GPO19/CLKDIV1
REGDMA/GPO18/CLKDIV0
VBAT
28
VBAT
BATRST
34
6–1
(4-2D) PWRDWN-
D6
D5
D4
148
147
146
145
D7
D6
D5
D4
D3
D2
D1
D0
144
143
142
141
D3
D2
D1
D0
A
1
2
3
4
5
6
UX-P115U
UX-P115U
FAX
Service
E
Market
Manual 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT
CHAPTER
[1] Control PWB circuit
1. Main control block
6–2
7
32
C
DG
C128
0.1u/25V
+3.3V
D0
D1
D2
D3
D4
D5
D6
D7
D
E
F
(1-3I) DWR-
(1-3I) CAS-
(1-3I) RAS-
R177
10k
G
+3.3V
G
R176
10k
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
N.M.
C198
OE
WE
CAS
RAS
NC
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
GND
GND
NC
VCC
VCC
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
H
IS41LV85125
22
7
23
8
6
10
11
12
13
16
17
18
19
20
9
IC2
DRAM
H
28
15
21
1
14
2
3
4
5
24
25
26
27
DG
I
D0
D1
D2
D3
D4
D5
D6
D7
2/6
+3.3V
C111
0.1u/25V
I
4
5
6
1
B
WE
OE
24
8
21
22
23
25
26
27
28
29
F
1
A
CE
GND
VDD
D0
D1
D2
D3
D4
D5
D6
D7
SST39VF020P
30
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
N.C.(A18)
E
2
0
N.M.
R123
R122 N.M.
20
19
18
17
16
15
14
13
3
2
31
1
12
4
5
11
10
6
9
D
2
R134
R135
10k
+3.3V
R121
10k
+3.3V
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
IC1
FLASH ROM
C
3
(1-4I) RD-
(1-4I) WR-
(1-3I) ROMCS-
(1-6I) D[7:0]
(1-5I) A[18:0]
B
3
4
5
6
Memory Block
A
UX-P115U
2. Memory block
6–3
1
2
3
4
5
6
SPMUTE
CNTH-5
A
CNL IUA-4
(5-1i) TMICHK
(4-1C) PHTSNSi
(5-2D) THLOOK
CNPRG-3
CNPRG-1
CNPW-7
(4-4C) FRSNS(4-4C) ORGSNS(4-5C) DR/RBN
CSWI
(4-6C)
(5-3E) VTHON
(5-5F) LEDON
CNLIUA-16
DG
C197 C193
C174
270
DG
270
R184
N.M.
52
53
MICMUTE
PSAVE
DG
C151
R159
N.M.
C152
C181
DG
DG
B
N.M.
R163
C192
DPMUTE
C191
R153
470
DPON
THRANK
DG
R126
CML
C195
R166
TELMUTE
C196
DG
N.M.
C
270
150
R172
R175
150
R171
R170
C1 60
1000p/50V
158
105
104
103
106
150
169
170
94
112
113
152
153
151
110
111
109
163
164
65
66
56
168
156
167
160
55
155
157
159
154
68
162
54
4
3
2
1
PIN
N.M.
RA4
270
51
5
6
7
8
C
RHS-
HS-
CI-
N.M.
CNLIUA-9
CNLIUA-6
RCVOL
CNLIUA-15
(5-3D)
THCHK
(6-1A)
(6-1E) DTMFMUTE
(6-3A) SIGMUTE
(6-4I)
CNLIUA-10
CNLIUA-1
N.M CNLIUA-13
CNL IUA-12
<CS5A>
<CS5>
FAX Modem Block
B
D
D
GPIO29
SASCLK2
SASTXD2
SASRXD2
DSS_PARK
VOL-A
VOL-B
VOL-C
FCS
FRD
FWR
FCLE
FALE
READY
SASRXD
SASTXD
GPIO3
GPIO35
GPIO36
GPIO11
GPIO19
VTHON
GPO1
GPO29
GPO0
GPIO32
GPIO37
GPO28
GPO30
GPIO31
GPO27
GPO25
GPIO34
GPIO13
GPIO17
GPIO16
GPIO15 / CS5
E
MIC_BIAS (IIA)
MIC_INM (IIA)
MIC_INP (IIA)
TESTC
MODE 0
N.C.
POR (IIA)
IARESET
SOUT (IIA)
SR3IN
SIN (IIA)
SR4OUT
CTRLI (IIA)
SR1IO
MCLK (IIA)
IACLK
ICLK (IIA)
IA1CLK
FSYNC (IIA)
SA1CLK
DVSS(IIA)
DVDD (IIA)
AGND (IIA)
VREF (IIA)
AVSS2 (IIA)
AVSS1 (IIA)
AVDD (IIA)
LINE_OUTP (IIA)
LINE_INP (IIA)
SPKR_OUTM (IIA)
SPKR_OUTP (IIA)
IC3
SCE209(2/2)
MODEM BLOCK
E
93
90
84
83
78
86
85
87
79
89
88
82
81
80
73
91
37
77
95
74
99
75
100
72
101
71
96
92
98
76
102
N.M.
C155
0.1u/25V
1K
R146
0.1u/16V-K
C156
DG
F
C136
0.1u/25V
C154
+
0.1u/25V
C9
C171
0.1u/25V 10u/50V
2.2K
R152
C172
DG
DG
F
+
A
C8
10u/50V
C5
10u/50V
+3.3V
+
DG
15
L104
G
DG
G
+3.3V
(6-4D)
SPOUT
H
(6-4F)
TELOUTI (6-5E)
SIGTX
SIGRX (6-2E)
H
I
I
3/6
1
2
3
4
5
6
UX-P115U
3. FAX Modem block
6–4
1
2
3
4
5
6
A
CNPHT-3
CNPN-8
CNPN-7
CNLiuA-11
CNCSW-1
+3.3V
R180
+3.3V
R181
C199
470p/50V
+3.3V
PHTSNS
FRSNS-
ORGSNS-
FILM
CSW -
B
DG
R182
51K
R140
270
R102
270
R101
270
R165
270
R149
C202
R183
3 +
1 -
IC 6
2
5
4
DG
DG
DG
DG
C
DG
C201
+3.3V
PWRDWN- (1-1G)
C105
1000p/50V
C104
1000p/50V
C194
1000p/50V
C163
100p/50V
R148
20k
+3.3V
(3-3A)
(3-3A)
PHTSNSi (3-2A)
N.M.
FRSNSi-
ORGSNSi- (3-3A)
DR/RBN
CSWi-
Sensor/Reset/Power Supply Block
C
D
D
E
CNPW-4
CNPW-3
CNPW-2
CNPW-1
CNPW-5
CNPW-6
E
MG
MG
+24V
+24V
DG
VREG
R150
+
N.M.
DG
F
CR2032
BAT1
F
R110 N.M.
C182
0.1u25V
5.6K
R100
MG
N.M.
C167
0.1u/50V
FG
R108
Vin
REG1
D101
1SS355
K
DG
G
+ C10
22u/50V
+24V
S-814A33AUA
3
K
HRW0202
+ C6
47u/25V
VREG
A2
D100
+3.3V
G
A1
B
VSS
2
A
Vout
<DG>
A
1
<VBT>
C134
1u/10V
<VBT1>
H
0
L102
H
R179
<DG>
<+3.3V>
N.M.
+ C3
220u/6.3V
+3.3V
VBAT
DG
DG
DG
DG
DG
I
I
CNLIUA-2
N.M.
CNPHT-2
CNPRG-2
CNCSW-2
CNPN-5
CNPN-6
N.M.
CNPHT-1
4/6
1
2
3
4
5
6
UX-P115U
4. Sensor/Reset/Power supply block
1
2
3
4
5
A
(5-5I)
CNCIS-1
+24V
+3.3V
DYNA
ROHM
CIS
Maker
LEDON-
VO
<VO>
N.M.
R1
R114
0
N.M.
0W
N.M.
VG
0.01u/50V
1000p/50V
C120
0.01u/50V
VG
DG
<VG>
C109
0.1u/25V
CISVDD
2SA1530AS
Q100
C120
DG
L100
0
C1
220u/6.3V
R173
B
R173
R1
0
300W(2W)
VG
R107
10K
B
R113
5.1K
CISVDD
E
C
6
C
C110
0.1u/50V
GLED
+24V
VG
CNCIS-6
CNCIS-7
CNCIS-2
CNCIS-3
<VIN>
VIN (1-2F)
TPATPB-
(1-1E)
(1-1E)
THCHK-
1K
R112
B
1K
1K
R128
R169
1K
R132
1K
1K
R131
R129
DG
R144
C
10k
DG
C166
C165
C164
C150
DG
Q101
RT1N141C
C
E
E
10k
Q109
RT1N141C
B
B
R143
4
3
2
1
8
7
6
5
4
3
2
1
120k
R168
1P141C
Q108
+24V
MG
02CZ18-Y
ZD100
N.M.
F
D
E
F
7C
6C
5C
4C
3C
2C
1C
COM
IC5
10
11
D3 7
D2 6
D1 5
S3
G
+3.3V
D4 8
S2
L103
0
G
THG
R136
470K
R137
20K
THG
N.M.
C153
+ C4
10u/50V
DG
N.M.
C7
R178
100k
H
C
DG
THG
DG
THI
DG
N.M.
C170
Q110
RT1N141C
B
THG
THG
THG
VTH
VTH
I
5/6
I
TMICHK (3-1A)
CNTH-4
THADI (1-2F)
CNTH-9
CNTH-8
CNTH-7
CNTH-6
CNTH-15
CNTH-1
LEDON- (5-3A)
THCHK- (5-3D)
CNMT-1
CNMT-2
CNMT-3
CNMT-4
CNLIUA-3
CNMT-6
CNMT-5
THVDD
THADI
C135
1u/10V
TPBD-
13
R145
0.1u/25V
TPAD-
12
TPBD
MG
VMT
+24VL
14
R151
22K
1N4748
ZD1
VMT
TPAD
S1
SI4431BDY
Q107
KAB3202
FU100
H
15
MG
G
16
9
+24V
ULN2001A
E
7B
6B
5B
4B
3B
2B
1B
NOTE:
This mark indicates a safety-critical part(s).
(3-2A) THLOOK
(5-5i)
(3-1A) VTHON
(3-2A) LEDON
(3-4A) THCHK
TPB
TPA
(1-1E)
(1-1F)
Video processing/Motor Driver/Thermal Block
D
E
C
E
C
6–5
E
B
+
A
1
2
3
4
5
6
UX-P115U
5. Video processing/Motor driver/Thermal block
1
2
3
4
5
6
A
(3-4A) RCVOL
CNLIUA-7
(3-6A) SIGMUTE
CNLIUA-8
CNLIUA-14
RXIN
TXOUT
TELOUT
B
1u/10V-K
Q103
RT1N141C
B
39k
R167
DG
C
B
0.1u/16V-K
C178
RT1N141C
C
Q104
DG
ZD101
C159
DG
E
DG
R156
1M
R157
7.5k
0
C176
C179
C
C
R154
3.9k
C
DG
C
B
Q102
RT1N141C
0.1u/16V-K
C177
1u/10V-K
C157
R158
Q106
B
R155
N.M.
DG
E
Main Control Block
E
C
D
Q105
C175
1u/10V-K
N.M.
C180
D
DG
B
TELIN
1SS355
D102
+3.3V
D103
+3.3V
(3-3A)
(3-2A)
(3-3H)
E
DTMFMUTE (3-6A)
CNLIUA-5
CML
SIGRX
SIGTX (3-3H)
RCVOL
TELOUTi (3-2H)
E
(3-3H) SPOUT
F
F
1u/10V
C131
20k
R119
G
R133
100k
G
120k
DG
H
DG
R117
1k
0.01u/50V
C126
C132
1u/10V
DG
IC4
NJM2113
R118
3 +
2
4 -
220k
R120
C133
220p/50V
H
VREG
7
B
E
6–6
E
1
6
8
5
DG
N .C
DG
C127
4700p/50V
20k
R116
C200
0.1u/25V
1
2
A
SP-
SP+
C2
47u/25V
6/6
I
BZOUT1 (1-1F)
SPMUTE (3-5A)
CNSP-3
CNSP-2
CNSP-1
I
1
2
3
4
5
6
UX-P115U
6. Analog signal block
UX-P115U
7. Control PWB parts layout (Top side)
6–7
UX-P115U
8. Control PWB parts layout (Bottom side)
6–8
A
B
C
DG
TP4
5
R2
+24VL (YELLOW)
2
SW1
3
SG206S
SG206S
PH1
2
4
( RED)
FILM
JP
TP2
PI N
( BROWN)
Ci
Vref A
TP3
JP
4
22uF/50v
DG
CNLIUA-11
CNLIUA-10
CNLIUA-12
DG
( ORANGE)
FILM
PI N
CNLIUA-1
JP
TP1
1
DG
Vref B
RHS-
FILM
2
DG
1
4
RA501P-C6
R104
3.3K
+24VA
DG
ZD2
HZ6A3
D1
1N4148
Q102
DG
DG
CML
DG
2
+24VA
CNLIUA-9
CNLIUA-2
CNLIUA-3
A
22k(1/2W)
Q1
+24VL
+24VL
R8
22k(1/4W)
ZD6
HZ27-A
R7
0.82uF/250(vF)
C6
RT1N436C
Q100
RT1N436C
A
R1
B
M
100(1/2W)
CML
OUAZ-SH-124DZ
+24VL
K
B
M
OUAZ-SH-124DZ
C
2k(1/2W)
Vref A
22uF/50v
R103
3.3K
C2
PIN
3
PH2
ARG
C3
C
C1
AR 3
1
L3
K5A R6H 6x10(W)2.5TS
M
RA391P-V6-2
HOOK SW
C
AR 1
1.2k(1W)
JP
Ring
+24VL
PC817X4
PC1
MJ1-4
4
3
R3
CML
100uF/50v
TiP
R5
R6
MJ1-3
PC1
PC817X4
1
3
DG
i2164
T1
D2
1N4148
C5
0.01u
51(1W)
R119
N.M.
C112
C7
4.7uF/50v
IC100
LM2902NS
K
KTC3198GR
100(1/4W)
150(1/4W)
R4
3.3K
D4
NOTE:
This mark indicates a safety-critical part(s).
K
D
1N4148
D3
TEL/LIU PWB Circuit
A
K
3
DG
R109
3.3k
8
C105
14
N.M.
DG
13
12
220k
220p
DG
DG
R112
16K
R102
47K
8.2K
R118
2
0
R124
1K
1.5K
R123
Vref B
13k
RT1N436C
5
L2
N.M.
Q103
Vref A
DG
N.M.
C108
2 -
+
R115
C109
3
J23
C107
N.M.
R114
56k
R113
DG
6
82K
220p
1
JP
DG
N.M.
J24
DG
JP
N.M.
C113
N.M.
L1
C101
0.1u
+24VA
TEL MUTE
TELI N
RX+
RX-
MICMUTE
TX-
TX+
IC100
LM2902NS
C114
2200p
R116
3.3k
11
4
39K
220p
C102
Vref A
3.6k
R107
1k
13k
R108
IC100
LM2902NS
R111
IC100
R100
3.3k
7
R106
C100
Vref A
2.2uF/50v
R122
0
C4
R117
C104
1000p
1K
R110
10uF/50v
C8
Vref A
Vref A
620
R101
2
IC100
LM2902NS
R120
C111
DG
1000p
R121
C110
1000p
10
27k
R105
9
1000p
C103
RT1P141C
ZD3
HZ2C1
Q101
C106
1000p
ZD4
HZ2C1
+
+
4
-
1N4148
+
6–9
A
-
5
CNLIUA-6
1
CNLIUA-5
MJTEL-2
MJTEL-3
CNLIUA-4
MJTEL-1
MJTEL-4
DG
HZ9C3
ZD5
Rxi n
DG
N.M.
ZD1
Txout
1
CNLIUA-7
CNLIUA-8
A
B
C
D
UX-P115U
[2] TEL/LIU PWB circuit
1. TEL/LIU PWB circuit
UX-P115U
2. TEL/LIU PWB parts layout (Top side)
The TEL/LIU PWB of the model
employs lead-free solder.
6 – 10
UX-P115U
3. TEL/LIU PWB parts layout (Bottom side)
The TEL/LIU PWB of the model
employs lead-free solder.
6 – 11
6 – 12
1
2
A
CNAC
B
C
D
R7
N.M.
18K
PC1
PS2501-1L
C5
0.015
R6
C17 18K
2.7K
R5
C24
390P
L2
RS912
R4
680
(7)
(8)
(10)
N.M.
D6
C6
0½
D5
1S2076A
1
R8
47K
C4
1000P
R30
100K
(12)
E
(6)
F
R14
1K
C12
0.1
R15
330K
Q4
2SC1740S
R17
3.3K
R13
4.7K
G
G
VR1
2.2K
R16
10K
R27
6.8K
FB3
(BP53RB052025050)
ZD5
RD6.2SAB2-T1
R18
3.3K
C10
330/16
D8
ERA81-004V3
(3) (4) (5)
C18
560/35
C13
2200P
D7
S3L20U
(1) (2)
T1
PTTN146-KTT
PC1
PS2501-1L
2
R10
0.15/1W
R9
47
ZD1
27HSB-26
Q1
2SK3306
ZD2
RD4.3SAB
F1
3.15A/125V
V1
S07K150GA
C3
470P
D9
ERA22-06V3
C31
4700P
F
NOTE:
Safety-critical unit.
E
C30
OPTION
R11
330K
R12
330K
C27
0.01
C26
0.01
C2
220/200
R2
470K
R3
470K
D
R29
6.8K
FB2
3A
F3
4A/32V
H
ZD8
RD10ESAB-T1
H
C32
OPTION
R28
6.8K
N.M.
C33
C1
0.22
R1
330K
L1
33mH/0.5A
D2 D4
D1 D3
10EDB60 x 4
C
C34
3
4
5
6
B
Power Supply PWB Circuit
A
I
I
6 +5V
5 GND
4 GND
3 GND
2 +24V
1 +24V
CNP5
1
2
3
4
5
6
UX-P115U
[3] Power supply PWB circuit
1. Power supply PWB circuit
ZD9
RD9.1ESAB2-T1
ZD4
HZ30CPTK
Q2
2SC4115S
Q3
2SC1741AS
UX-P115U
2. Power supply PWB parts layout (Top side)
3. Power supply PWB parts layout (Bottom side)
6 – 13
6 – 14
A
B
C
CNPN- 8
CNPN- 7
CNPN- 5
CNPN- 6
CNPN- 9
CNPN- 1
CNPN- 2
CNPN- 3
CNPN- 4
CNPN-16
CNPN-15
CNPN-14
CNPN-13
CNPN-12
CNPN-11
FRSNS
ORGSNS
DG
+3.3V
E
KEN4A
KEN3A
KEN2A
KEN1A
SEN6
SEN5
SEN4
SEN3
SEN2
SEN1
4
FRSNS
ORGSNS
DG
D3
D4
D7
C1
0.022u/50V
A
A
A
A
A
A
A
+3.3V
1N4148
K
1N4148
K
D6
1N4148
K
D5
1N4148
K
1N4148
K
1N4148
K
D2
(10k )
R4
D
D1
1N4148
K
(10k)
R1
SEN0
(10k)
R5
CNPN-10
(10k)
R6
Operation Panel PWB Circuit
sw22
8
sw10
0
sw13
UP
sw19
DOWN
sw23
KEY-1
sw26
7
sw 9
*
sw12
STOP
sw17
REDIAL
sw16
KEY-2
sw24
DG
START
sw 7
sw 6
R2
R3
sw25
(6.2k)
JP(1k)
DG
sw27
sw20
N.M.
KEY-3
A
sw15
COPY
sw28
C2
DG
N.M.
SPEAKER
#
sw14
sw21
FLASH
sw11
8
sw 8
sw18
RESOLUTION
FUNCTION
6
5
4
3
sw 5
2
sw 4
1
3
3
sw 3
N.M.
4
DG
+3.3V
VO
E
R/W
RS
LD3
LD2
LD1
LD0
2
CNLCD-1
CNLCD-2
CNLCD-3
CNLCD-6
CNLCD-5
CNLCD-4
CNLCD-14
CNLCD-13
CNLCD-12
CNLCD-11
2
E
R/W
5
LD1
LD2
LD3
13
14
N.C
LD0
11
12
N.C
10
N.C
8
9
N.C
7
E
RS
4
6
VO
2
3
DG
+3.3V
1
CNLCD
SEN6
SEN4
14
SEN5
SEN3
13
16
SEN2
12
15
SEN1
11
SEN0
FRSNS
9
10
ORGSNS
5
8
DG
4
+3.3V
KEN1A
3
7
KEN2A
2
6
KEN4A
KEN3A
1
CNPN
1
NOTE:
This mark indicates a safety-critical part(s).
1
A
B
C
D
UX-P115U
[4] Operation Panel PWB circuit
1. Operation Panel PWB circuit
UX-P115U
2. Operation panel PWB parts layout (Top side)
Since the parts of PWB cannot be supplied, change it as a unit.
The Operation panel PWB of
the model employs lead-free
solder.
•
6 – 15
UX-P115U
3. Operation panel PWB parts layout (Bottom side)
•
Since the parts of PWB cannot be supplied, change it as a unit.
The Operation panel PWB of
the model employs lead-free
solder.
6 – 16
UX-P115U
UX-P115U
FAX
Service
E
Market
Manual 7. OPERATION FLOWCHART
CHAPTER
[1] Protocol
Receive side
G3 communication
Transmitter side
(Document inserted into
document sensor during
standby)
CED
To recording
position
CED
NSF
NSF
CSI
CSI
DIS
DIS
TSI
Document inserted to
the reading position
TSI
(DCS)
NSS
NSS
(DCS)
TCF
TCF
CFR
IMAGE
SIGNAL
IMAGE
SIGNAL
CFR
1st page
RTC
RTC
Next page insert
command
Cut line printed
MPS
MPS
MCF
IMAGE
SIGNAL
IMAGE
SIGNAL
MCF
RTC
RTC
EOP
EOP
Cut line printed
MCF
MCF
DCN
DCN
Recording paper ejected
7–1
Document ejected
UX-P115U
[2] Power on sequence
START
CPU initialized
MODEM initialized
ÒWAIT A MOMENTÓ display
STOP key ?
NO
ÒMEMORY CLEAR ?Ó display
NO
3 sec ?
YES
1
YES
STAND-BY
START key ?
NO
2
YES
COPY key ?
1
2
ÒMEMORY CLEAREDÓ display
ÒMEMORY CLEAREDÓ display
Memory clear
Memory clear
STAND-BY
PROCESS CHECK MODE
NO
YES
STOP key ?
NO
3 sec ?
NO
YES
STAND-BY
7–2
UX-P115U
UX-P115U
FAX
Service
E
Market
Manual 8. OTHER
CHAPTER
[1] Service tools
1. List
NO.
1
2
PARTS CODE
DESCRIPTION
CPWBF3201SCS1
PSHEZ3579SCZZ
Extension board unit (TEL/LIU PWB)
Shading wave memory standard paper
Q'TY
1
1
PRICE
RANK
BA
AD
1.1. Extension board unit
TEL/LIU PWB
PH2
K A
TP1
PIN
(BROWN)
PH1
TP3
DG
(ORANGE)
C
E
C E
R30
K
A
TP2
FILM
(RED)
TP4
+24VL
(YELLOW)
NO.
1
2
3
4
5
6
7
8
9
10
PARTS CODE
QCNWG471BSCZZ
QCNWG206BSCZZ
QCNWG202BSCZZ
QCNWG205BSCZZ
QCNWG204BSCZZ
QCNWG242BSCZZ
QCNWG201BSCZZ
VRS-RE3AA122J
VHPSG206S//-1
VHPSG206S//-1
DESCRIPTION
SPEAKER RELAY CABLE
PANEL RELAY CABLE
CIS RELAY CABLE
HEAD RELAY CABLE
CAM SWITCH RELAY CABLE
MOTOR RELAY CABLE
SENSOR RELAY CABLE
RESISTOR (1W 1.2KΩ ±5%)[R30]
PHOTO TRANSISTOR [PH1]
PHOTO TRANSISTOR [PH2]
Q'TY
1
1
1
1
1
1
1
1
1
1
8–1
PRICE
RANK
AN
AT
AN
AS
AG
AM
BB
AC
AG
AG
UX-P115U
2. Relay board unit
2.1. Relay board unit
1. Remove the TEL/LIU, Control PWB and Power Supply PWB from
this unit, and mount the board unit instead.
Before connecting the wiring to the relay board unit, set the test
PWB switches to the fixed position.
2. The setting is as follows.
• The relay cables are used as one pair.
• The hook switch is manually operated.
Relay
cable
1
CNLIUA
CNLIUA
12
CHECK
TEL/LIU
PWB
The hook switch is operated by the mechanical unit switch and the test
PWB switch. When performing installation in the machine unit, set the
test PWB switches to the fixed position.
Mechanical unit
PWB to be tested
Actual operation with mechanical unit
Hook SW
ON/OFF operation
ON-HOOK
PWB sensor check
CNPS
CNPW
POWER
SUPPLY
PWB
Hook SW
ON-HOOK
ON/OFF operation
CHECK
CONTROL
PWB
NOTE
CHECK
CONTROL
PWB
DON'T SEPARATE
CHECK
TEL/LIU
PWB
UNIT
RELAY CABLE
PAPER SENSOR RELAY CABLE (QCNWG201BSCZZ)
PIN(TP1) (TEL/LIU)
TO
FILM(TP2) (TEL/LIU)
EXTENSION
DG(TP3) (TEL/LIU)
PWB
+24VL(TP4)(TEL/LIU)
BROWN
RED
ORANGE
POWER
SUPPLY
PWB
TO
CHECK
PWB
YELLOW
8–2
UX-P115U
3. Shading paper
•
The white and black basis is applied to remember the shading
waveform. Be sure to perform this operation when replacing the
battery or replacing the control PWB. Execute in the shading mode
of DIAG mode.
SHADING WAVE MEMORY STANDARD PAPER (PSHEZ3579SCZZ)
8–3
UX-P115U
[2] Changing the record paper size
1. How to change the A4 size and letter size of the
record papers
1) It becomes the record paper of the A4 size by installing A4 guide
(PGiDM2629XHZZ)
which shows in the drawing. Remove A4 guide when you use the
record paper of the letter size.
Paper tray ass'y
Hook
A4 Guide
PGiDM2629XHZZ
2) Set soft switch SW-L2 No.1 and the initialization of SW-L2 No.2 as
follows.
SW
NO.
SW
l
L2
DATA
NO.
Switch setting and function
ITEM
1
Paper set size
1
2
No. 1
No. 2
8–4
Initial
setting
0
LETTER
0
0
LEGAL
0
1
A4
1
0
Remarks
OPTION
0
0
UX-P115U
- MEMO -
8–5
UX-P115U
PARTS GUIDE
MODEL
MODEL
UX-P115
UX-P115
SELECTION CODE DESTINATION
U
U.S.A.
CONTENTS
[1]
Cabinet,etc.
[6]
Control PWB unit
[2]
Top cover/Sub frame
[7]
TEL/LIU PWB unit
[3]
Upper cabinet/Document guide
upper
[8]
Power supply PWB unit
[9]
Operation panel PWB unit
„
INDEX
[4]
Drive unit
[5]
Packing material & Accessories
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
UX-P115U
[1] Cabinet,etc.
62
27
OPERATION
PANEL UNIT
16
DOCUMENT
GUIDE UPPER
22
B1
30
63
31 33
34
28
25
25
TOP COVER/
SUB FRAME
64
23
32
24
B2
26
26
4
B4
B1
29
57
B2
41
49
29
68
B2
65
42
66
45
55
36
39
38
44
39
40
B3
43
W1
59
66
7
35
B1
37
58
3
61
48
47
46
52
54
50
B1
6
51
53
5
67 W2
B1
DRIVE
UNIT
B1
16
B1
2
8
17
UX-P115U
NO.
PARTS CODE
PRICE NEW PART
RANK MARK RANK
DESCRIPTION
[1] Cabinet,etc.
!
!
3
4
5
6
7
8
16
17
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
57
58
59
61
62
63
64
65
66
67
68
B1
B2
B3
B4
W1
W2
CCNWN395BXH01
CLEVP2358XH01
CROLR2481XH01
DCEKC688TXHZZ
DCEKL477CXH02
QPWBF3368XHZ2
QCNWN399BXHZZ
LBNDJ2006XHZZ
LBSHP2140XHZA
LBSHP2143XHZZ
LFRM-2225XHVA
MSPRC3295XHZZ
MSPRD3379XHZZ
NGERH2569XHZZ
NGERH2570XHZZ
NROLP2332XHZZ
NROLR2482XHZZ
PGIDM2617XHZZ
PGIDM2618XHZZ
QCNWN419BXHZZ
RUNTZ2127XHZZ
GCABB2393XHSH
LHLDZ2227XHZZ
LHLDZ2228XHZZ
MSPRC3287XHZZ
MSPRC3288XHZZ
MSPRC3340XHZA
PCOVP2130XHZZ
PGIDM2615XHZZ
PGIDM2616XHZZ
QCNWN486AXHZZ
RHEDZ2065XHZZ
GCOVA2447XHVA
GLEGG2078XHZZ
LPLTM3178XHZZ
LPLTP3177XHZZ
MLEVP2357XHZZ
MLEVP2356XHZA
MSPRD3286XHZA
MSPRD3285XHZZ
MSPRD3291XHZZ
MSPRD3292XHZA
PCOVP2131XHVA
PCOVP2132XHZZ
QACCD2090XHZZ
RDENT2198XHZZ
HPNLH2420XHSN
PBRS-2055XHZZ
PSHEZ3687XHZZ
MSPRD3341XHZZ
MSPRC3346XHZZ
MSPRC3357XHZZ
TLABH498FXHZZ
XEBSD30P10000
XEBSD30P12000
LX-BZ2282XHZZ
XEPSD30P08000
XWHSN40-08100
LX-WZ2290XHZZ
AP
AD
AQ
BT
BG
AQ
AP
AA
AC
AC
AP
AB
AD
AC
AD
AD
AR
AD
AD
AL
N
N
AZ
AD
AD
AB
AB
AD
AE
AD
AD
AM
BP
AL
AD
AF
AD
AD
AD
AB
AB
AD
AB
AG
AD
AS
BG
AM
AN
AD
AD
AD
AD
AH
AA
AA
AB
AA
AA
AE
N
N
Speaker ass'y
Hook switch lever ass'y
PO roller ass'y
Control PWB unit(Within ROM)
TEL/LIU PWB unit
Wire holder(PWB only)
Panel cable
Band(100mm)
Back bearing,left
Back bearing,right
Scanner frame
CIS spring
PO pinch roller spring
Back gear
Reduction gear,21/37Z
PO pinch roller
Back roller
CIS guide,left
CIS guide,right
CIS cable
CIS unit
Lower cabinet
Ink ribbon spool 1
Ink ribbon spool 2
Head spring A
Head spring B
Head spring C
Head cover
Head guide,left
Head guide,right
Head cable
Thermal head
Front cover
Rubber leg
Bottom plate
Stopper plate
Film sensor lever
P-IN sensor lever,lower
Film sensor lever spring
P-IN sensor lever spring,lower
Speaker hold spring
Head earth spring
Panel cable cover
Control PWB cover
AC cord ass'y
Power supply PWB unit
Decoration panel
Static brush
Earth sheet
Up spring
Head spring D
PO roller spring
Imaging film set label
Screw(3x10)
Screw(3x12)
Screw(4x6)
Screw(3x8)
Washer
Washer
C
C
C
E
E
E
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
D
C
C
C
C
C
C
C
C
C
B
D
C
C
C
C
C
C
C
C
C
C
C
B
E
D
C
C
C
C
C
D
C
C
C
C
C
C
3
UX-P115U
[2] Top cover/Sub frame
27
25
16
28
26
15
B1 12
B2
30
B1
20
B2
4
29
NO.
24
3
2
B3
PARTS CODE
6
11
1
22
5
B2
19
23
13
8
24
21
22
18
B2
GCOVA2448XHVA
MSPRC3301XHZZ
NGERP2318XHZZ
PGIDM2619XHVA
PGIDM2620XHVA
LFRM-2227XHZZ
LFRM-2232XHZZ
MLEVP2363XHZZ
MSPRC3305XHZZ
MSPRD3302XHZZ
NGERH2580XHZZ
NGERH2581XHZZ
NROLR2483XHZZ
NROLR2504XHZZ
NSFTP2357XHZZ
NSFTP2374XHZZ
PGIDM2621XHSA
LHLDZ2224XHZZ
LPLTG3181XHZZ
LPLTP3179XHZZ
LPLTP3180XHZZ
LPLTP3182XHZZ
MSPRC3299XHZZ
MSPRC3300XHZZ
LBSHP2148XHZA
LBSHP2149XHZA
NGERH2579XHZA
NROLR2485XHZZ
LBNDJ2006XHZZ
MSPRC3335XHZZ
LX-BZ2234XHZZ
XEBSD30P10000
LX-BZ2222XHZZ
7
17
B2
PRICE NEW PART
RANK MARK RANK
AX
AB
AD
AG
AG
AQ
AT
AD
AB
AB
AC
AC
AL
AL
AG
AG
AF
AL
AD
AD
AH
AH
AB
AB
AE
AE
AE
AQ
AA
AD
AD
AA
AC
10
9
DESCRIPTION
[2] Top cover/Sub frame
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
B1
B2
B3
14
Top cover
Hopper spring
Pinion gear
Hopper guide,left
Hopper guide,right
Sub frame
Sub frame plate
P-IN sensor lever,upper
Release lever spring
P-IN sensor lever spring,upper
Reduction gear,15/22Z
Idler gear,25Z
Paper feed roller
PU roller
Paper feed roller shaft
PU roller shaft
Release lever
RP feed plate holder
RP separate rubber
RP separate base
RP separate plate
RP feed plate
RP separate spring
RP feed spring
Platen bearing,left
Platen bearing,right
Platen gear
Platen roller
Band
Paper feed roller spring
Screw
Screw(3x10)
Screw
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
4
UX-P115U
[3] Upper cabinet/Document guide upper
21
901
9
10
5
1
6
12
19
13
3
7
15
4
17
2
B1
8
11
18
14
16
NO.
PARTS CODE
PRICE NEW PART
RANK MARK RANK
DESCRIPTION
[3] Upper cabinet/Document guide upper
!
!
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
21
B1
901
GCASP2173XHSA
JBTN-2357XHSB
JBTN-2359XHSD
JBTN-2358XHSC
DCEKP478CXH02
QSW-Q2331XHZZ
QSW-M2246AXZZ
QSW-M2294XHZZ
QCNWN399BXHZZ
RUNTZ2127XH01
LPLTG2911XHZZ
LPLTP3175XHZZ
LPLTP3176XHZZ
MSPRD3293XHZZ
MSPRT3294XHZZ
PGIDM2614XHSA
PSHEP3660XHZZ
JBTN-2360XHSC
JBTN-2361XHSD
HPNLH2420XHSN
XEBSD20P06000
(Unit)
DCEKP480CXH02
BA
AK
AQ
AP
BG
AE
AH
AE
AP
BC
AE
AD
AD
AB
AB
AL
AE
AH
AM
AM
AA
BG
N
N
D
C
C
C
E
C
C
C
C
E
C
C
C
C
C
C
C
C
C
D
C
Panel case
12 key
Start key
Function key
Operation panel PWB unit
Tact switch
FRSNS sensor
ORGSNS sensor
Panel cable
LCD unit
Separate rubber
Separate plate
Feed plate
Separate spring
Feed spring
Document guide upper
Separate rubber sheet
Speed key
Function 2 key
Decoration panel
Screw(2x6)
E
Operation panel unit
5
[SW]
UX-P115U
[4] Drive unit
1
16
15
4
18
11
8
21
B1
14
23
7
22
3
15
20
6
9
10 2
12
19
13
5
NO.
PARTS CODE
10
PRICE NEW PART
RANK MARK RANK
DESCRIPTION
[4] Drive unit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
B1
CGERH2314XH05
CLEVP2359XH01
CLEVP2360XH01
CLEVP2361XH01
CLEVP2362XH01
LFRM-2226XHZZ
LPLTM3190XHZZ
MCAMP2028XHZZ
MSPRD3298XHZZ
NGERH2380XHZZ
NGERH2409XHZZ
NGERH2571XHZZ
NGERH2572XHZZ
NGERH2573XHZZ
NGERH2574XHZZ
NGERH2575XHZZ
NGERH2576XHZZ
NGERH2577XHZZ
NGERH2582XHZZ
QCNWN483AXHZZ
QSW-F2224SCZZ
RMOTS2175XHZZ
MSPRP3297XHZZ
XEBSD30P08000
AS
AD
AD
AD
AD
AQ
AG
AE
AE
AC
AB
AD
AD
AD
AD
AD
AD
AD
AC
AD
AE
AX
AD
AA
N
17
Slip gear ass'y
Planet gear lever ass'y A
Planet gear lever ass'y B
Planet gear lever ass'y C
Planet gear lever ass'y D
Drive unit frame
Motor plate
Cam
Cam hold spring
Reduction gear,17/36Z
Idler gear,23Z
Slip gear
Reduction gear,25/63Z
Reduction gear,20/40Z
Reduction gear,15/30Z
Idler gear,40Z
Idler gear,21Z
Idler gear,20Z
Idler gear,15Z
Cam switch cable
Cam switch
Motor
Earth spring
Screw(3x8)
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
C
6
UX-P115U
[5] Packing material & Accessories
12
14
TAPE
4
2
6
21
TAPE
TAPE
16
15
3
TAPE
11
24
18
AC CORD
R
23
17
5
1
(3)
(1)
(2)
(4)
20
R
NO.
PARTS CODE
PRICE NEW PART
RANK MARK RANK
DESCRIPTION
[5] Packing material & Accessories
!
!
1
2
3
4
5
6
11
12
14
15
16
17
18
20
21
23
24
DUNTK497CXHFW
QCNWG209BXHOW
CPLTP3222XHR2
NGERH2568XHZZ
PRBNN2038SC10
QCNWG370BXHZZ
TINSE4463XHTZ
TCADZ3745XHZZ
SPAKA465CXHZZ
SPAKA466CXHZZ
SPAKA467CXHZZ
CPAKC271GXH01
SPAKP329DXHZZ
CPLTP3183XHRF
CGERH2566XH01
TCADZ2891XHZZ
TCADZ3744XHZZ
AY
AH
AQ
AB
AL
AL
BC
AL
AF
AF
AD
AV
AF
AV
AG
AF
AL
N
N
N
N
E
C
C
C
S
C
D
D
D
D
D
D
D
C
C
D
D
Handset
Handset cord
Paper tray extension ass'y
Imaging film gear
Imaging film(Initial starter film 10m)
Telephone line cord
Operation manual
Pop card
Packing add.,left
Packing add.,right
Packing add.,accessories
Packing case with label
Vinyl cover
Paper tray ass'y
Imaging film gear ass'y
Registration card
Setup guide
B
C
C
C
C
C
C
C
C
C
C
C
C
C
Battery(CR2032T23)
Capacitor(6.3WV 220µ F)
Capacitor(25WV 47µ F)
Capacitor(6.3WV 220µ F)
Capacitor(50WV 10µ F)
Capacitor(50WV 10µ F)
Capacitor(25WV 47µ F)
Capacitor(50WV 10µ F)
Capacitor(50WV 10µ F)
Capacitor(50WV 22µ F)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(50WV 100PF)
Capacitor(50WV 100PF)
[6] Control PWB unit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
UBATL2049SCZZ
VCEAGA0JW227M
VCEAGA1EW476M
VCEAGA0JW227M
VCEAGA1HW106M
VCEAGA1HW106M
VCEAGA1EW476M
VCEAGA1HW106M
VCEAGA1HW106M
VCEAGA1HW226M
VCKYCY1HB102K
VCKYCY1HB102K
VCCCCY1HH101J
VCCCCY1HH101J
AF
AD
AA
AD
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
7
[BAT1]
[C1]
[C2]
[C3]
[C4]
[C5]
[C6]
[C8]
[C9]
[C10]
[C104]
[C105]
[C107]
[C108]
UX-P115U
NO.
PARTS CODE
PRICE NEW PART
RANK MARK RANK
DESCRIPTION
[6] Control PWB unit
!
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
VCKYCY1HF104Z
VCKYCY1HF104Z
VCKYCY1HF104Z
VCKYCY1HF104Z
VCCCCY1HH101J
VCCCCY1HH101J
VCCCCY1HH101J
VCKYCY1HF104Z
VCCCCY1HH101J
VCCCCY1HH101J
VCKYCY1HF104Z
VCKYCY1HB103K
VCKYCY1HF104Z
VCCCCY1HH330J
VCCCCY1HH150J
VCKYCY1HB103K
VCKYCY1HB472K
VCKYCY1HF104Z
VCKYCY1HF104Z
VCKYCY1HF104Z
VCKYCY1AF105Z
VCKYCY1AF105Z
VCCCCY1HH221J
VCKYCY1AF105Z
VCKYCY1AF105Z
VCKYCY1HF104Z
VCKYCY1HF104Z
VCKYCY1AF105Z
VCKYCY1HF104Z
VCKYCY1HF104Z
VCKYCY1AF105Z
VCKYCY1AF105Z
VCKYCY1AF105Z
VCKYCY1AF105Z
VCKYCY1AF105Z
VCKYCY1AF105Z
VCCCCY1HH220J
VCCCCY1HH220J
VCKYCY1HF104Z
VCKYCY1HF104Z
VCKYCY1AB105K
VCKYCY1AB105K
VCKYCY1HB102K
VCKYCY1AF105Z
VCKYCY1AF105Z
VCCCCY1HH101J
VCKYCY1HF104Z
VCCCCY1HH101J
VCCCCY1HH101J
VCKYCY1HF104Z
VCKYCY1CB104K
VCKYCY1AB105K
VRS-CY1JB000J
VCKYCY1CB104K
VCKYCY1CB104K
VCKYCY1HF104Z
VCCCCY1HH101J
VCCCCY1HH101J
VCCCCY1HH101J
VCCCCY1HH101J
VCCCCY1HH101J
VCKYCY1HB102K
VCKYCY1HB102K
VCKYCY1HB102K
VCKYCY1HB471K
VCKYCY1HF104Z
QCNCM2666XH0G
QCNCM7014SC0B
QCNCM2508SC1B
QCNCM7014SC0F
QCNCM2666XH1F
QCNCM7014SC0C
QCNCM2638SC0F
QCNCM2666XH0C
QCNCM7014SC1E
VHDHRW0202B-1
VHD1SS355//-1
VHD1SS355//-1
QFS-L1037YCZZ
VHIF002/TC89B
RH-IX2321XHZZ
VHISCE209//-1
VHINJM2113M-1
RH-IX2356XHZZ
VRS-CY1JB000J
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AC
AC
AA
AC
AC
AA
AA
AC
AA
AA
AC
AC
AC
AC
AC
AC
AA
AA
AA
AA
AB
AB
AA
AC
AC
AA
AA
AA
AA
AA
AB
AB
AA
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AE
AD
AF
AB
AF
AA
AE
AD
AC
AD
AB
AB
AD
BD
AX
BH
AG
AL
AA
N
Capacitor(50WV 0.1µ F)
Capacitor(50WV 0.1µ F)
Capacitor(50WV 0.1µ F)
Capacitor(50WV 0.1µ F)
Capacitor(50WV 100PF)
Capacitor(50WV 100PF)
Capacitor(50WV 100PF)
Capacitor(50WV 0.1µ F)
Capacitor(50WV 100PF)
Capacitor(50WV 100PF)
Capacitor(50WV 0.1µ F)
Capacitor(50WV 0.01µ F)
Capacitor(50WV 0.1µ F)
Capacitor(50WV 33PF)
Capacitor(50WV 15PF)
Capacitor(50WV 0.01µ F)
Capacitor(50WV 4700PF)
Capacitor(50WV 0.1µ F)
Capacitor(50WV 0.1µ F)
Capacitor(50WV 0.1µ F)
Capacitor(10WV 1µ F)
Capacitor(10WV 1µ F)
Capacitor(50WV 220PF)
Capacitor(10WV 1µ F)
Capacitor(10WV 1µ F)
Capacitor(50WV 0.1µ F)
Capacitor(50WV 0.1µ F)
Capacitor(10WV 1µ F)
Capacitor(50WV 0.1µ F)
Capacitor(50WV 0.1µ F)
Capacitor(10WV 1µ F)
Capacitor(10WV 1µ F)
Capacitor(10WV 1µ F)
Capacitor(10WV 1µ F)
Capacitor(10WV 1µ F)
Capacitor(10WV 1µ F)
Capacitor(50WV 22PF)
Capacitor(50WV 22PF)
Capacitor(50WV 0.1µ F)
Capacitor(50WV 0.1µ F)
Capacitor(10WV 1µ F)
Capacitor(10WV 1µ F)
Capacitor(50WV 1000PF)
Capacitor(10WV 1µ F)
Capacitor(10WV 1µ F)
Capacitor(50WV 100PF)
Capacitor(50WV 0.1µ F)
Capacitor(50WV 100PF)
Capacitor(50WV 100PF)
Capacitor(50WV 0.1µ F)
Capacitor(16WV 0.1µ F)
Capacitor(10WV 1µ F)
Resistor(1/16W 0Ω ± 5%)
Capacitor(16WV 0.1µ F)
Capacitor(16WV 0.1µ F)
Capacitor(50WV 0.1µ F)
Capacitor(50WV 100PF)
Capacitor(50WV 100PF)
Capacitor(50WV 100PF)
Capacitor(50WV 100PF)
Capacitor(50WV 100PF)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(50WV 470PF)
Capacitor(50WV 0.1µ F)
Connector(7pin)
Connector(2pin)
Connector(12pin)
Connector(6pin)
Connector(16pin)
Connector(3pin)
Connector(6pin)
Connector(3pin)
Connector(15pin)
Diode(HRW0202B)
Diode(1SS355)
Diode(1SS355)
IC protector(KAB3202)
IC,FLASH ROM(2MB)(Ver.:TC89B)
IC(IS41LV85125)
IC(SCE209)
IC(NJM2113M)
IC(ULN2001A)
Resistor(1/16W 0Ω ± 5%)
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
A
B
B
B
B
B
C
8
[C109]
[C110]
[C111]
[C112]
[C113]
[C114]
[C115]
[C116]
[C117]
[C118]
[C119]
[C120]
[C121]
[C122]
[C123]
[C126]
[C127]
[C128]
[C129]
[C130]
[C131]
[C132]
[C133]
[C134]
[C135]
[C136]
[C137]
[C139]
[C140]
[C141]
[C142]
[C143]
[C144]
[C145]
[C146]
[C147]
[C148]
[C149]
[C154]
[C155]
[C157]
[C159]
[C160]
[C161]
[C162]
[C163]
[C167]
[C168]
[C169]
[C171]
[C172]
[C175]
[C176]
[C177]
[C178]
[C182]
[C183]
[C184]
[C185]
[C186]
[C187]
[C188]
[C189]
[C194]
[C199]
[C200]
[CNCIS]
[CNCSW]
[CNLIUA]
[CNMT]
[CNPN]
[CNPRG]
[CNPW]
[CNSP]
[CNTH]
[D100]
[D101]
[D102]
[FU100]
[IC1]
[IC2]
[IC3]
[IC4]
[IC5]
[L100]
UX-P115U
NO.
PARTS CODE
PRICE NEW PART
RANK MARK RANK
DESCRIPTION
[6] Control PWB unit
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
VRS-CY1JB000J
VRS-CY1JB000J
VRS-CY1JB150J
VS2SA1530AS-1
VSRT1N141C/-1
VSRT1N141C/-1
VSRT1N141C/-1
VSRT1N141C/-1
VSSI4431BDY-1
VSRT1P141C+-1
VSRT1N141C/-1
VSRT1N141C/-1
VRS-CY1JB562J
VRS-CY1JB271J
VRS-CY1JB271J
VRS-CY1JB000J
VRS-CY1JB471J
VRS-CY1JB471J
VRS-CY1JB471J
VRS-CY1JB103J
VRS-CY1JB271J
VRS-CY1JB102J
VRS-CY1JB512J
VRS-CY1JB000J
VRS-CY1JB203J
VRS-CY1JB102J
VRS-CY1JB124J
VRS-CY1JB203J
VRS-CY1JB224J
VRS-CY1JB103J
VRS-CY1JB151J
VRS-CY1JB103J
VRS-CY1JB471J
VRS-CY1JB105J
VRS-CY1JB102J
VRS-CY1JB102J
VRS-CY1JB301J
VRS-CY1JB102J
VRS-CY1JB102J
VRS-CY1JB104J
VRS-CY1JB000J
VRS-CY1JB103J
VRS-CY1JB474J
VRS-CY1JB203J
VRS-CY1JB224J
VRS-CY1JB513J
VRS-CY1JB271J
VRS-CY1JB106J
VRS-CY1JB103J
VRS-CY1JB103J
VCKYCY1HF104Z
VRS-CY1JB102J
VRS-CY1JB000J
VRS-CY1JB203J
VRS-CY1JB271J
VRS-CY1JB223J
VRS-CY1JB222J
VRS-CY1JB392J
VRS-CY1JB105J
VRS-CY1JB752J
VRS-CY1JB271J
VRS-CY1JB271J
VRS-CY1JB271J
VRS-CY1JB271J
VRS-CY1JB393J
VRS-CY1JB124J
VRS-CY1JB102J
VRS-CY1JB271J
VRS-CY1JB151J
VRS-CY1JB151J
VRS-CY1JB000J
VRS-CY1JB101J
VRS-CY1JB271J
VRS-CY1JB103J
VRS-CY1JB103J
VRS-CY1JB104J
RR-TZ3018SCZZ
RR-TZ3018SCZZ
RR-TZ3018SCZZ
RR-TZ3017SCZZ
RH-IX2357XHZZ
RCRSP2176SCZZ
RCRSB0297AFZZ
VHE1N4748A/-1
VHE02CZ180Y-1
AA
AA
AA
AC
AB
AB
AB
AB
AL
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
AC
AC
AC
AH
AG
AD
AC
AC
N
Resistor(1/16W 0Ω ± 5%)
Resistor(1/16W 0Ω ± 5%)
Resistor(1/16W 15Ω ± 5%)
Transistor(2SA1530AS)
Transistor(RT1N141C)
Transistor(RT1N141C)
Transistor(RT1N141C)
Transistor(RT1N141C)
FET(SI4431BDY)
Transistor(RT1P141C)
Transistor(RT1N141C)
Transistor(RT1N141C)
Resistor(1/16W 5.6KΩ ± 5%)
Resistor(1/16W 270Ω ± 5%)
Resistor(1/16W 270Ω ± 5%)
Resistor(1/16W 0Ω ± 5%)
Resistor(1/16W 470Ω ± 5%)
Resistor(1/16W 470Ω ± 5%)
Resistor(1/16W 470Ω ± 5%)
Resistor(1/16W 10KΩ ± 5%)
Resistor(1/16W 270Ω ± 5%)
Resistor(1/16W 1KΩ ± 5%)
Resistor(1/16W 5.1KΩ ± 5%)
Resistor(1/16W 0Ω ± 5%)
Resistor(1/16W 20KΩ ± 5%)
Resistor(1/16W 1KΩ ± 5%)
Resistor(1/16W 120KΩ ± 5%)
Resistor(1/10W 20KΩ ± 5%)
Resistor(1/16W 220KΩ ± 5%)
Resistor(1/16W 10KΩ ± 5%)
Resistor(1/16W 150Ω ± 5%)
Resistor(1/16W 10KΩ ± 5%)
Resistor(1/16W 470Ω ± 5%)
Resistor(1/16W 1MΩ ± 5%)
Resistor(1/16W 1KΩ ± 5%)
Resistor(1/16W 1KΩ ± 5%)
Resistor(1/16W 300Ω ± 5%)
Resistor(1/16W 1KΩ ± 5%)
Resistor(1/16W 1KΩ ± 5%)
Resistor(1/16W 100KΩ ± 5%)
Resistor(1/16W 0Ω ± 5%)
Resistor(1/16W 10KΩ ± 5%)
Resistor(1/16W 470KΩ ± 5%)
Resistor(1/16W 20KΩ ± 5%)
Resistor(1/16W 220KΩ ± 5%)
Resistor(1/16W 51KΩ ± 5%)
Resistor(1/16W 270Ω ± 5%)
Resistor(1/16W 10MΩ ± 5%)
Resistor(1/16W 10KΩ ± 5%)
Resistor(1/16W 10KΩ ± 5%)
Capacitor(50WV 0.1µ F)
Resistor(1/16W 1KΩ ± 5%)
Resistor(1/16W 0Ω ± 5%)
Resistor(1/16W 20KΩ ± 5%)
Resistor(1/16W 270Ω ± 5%)
Resistor(1/16W 22KΩ ± 5%)
Resistor(1/16W 2.2KΩ ± 5%)
Resistor(1/16W 3.9KΩ ± 5%)
Resistor(1/16W 1MΩ ± 5%)
Resistor(1/16W 7.5KΩ ± 5%)
Resistor(1/16W 270Ω ± 5%)
Resistor(1/16W 270Ω ± 5%)
Resistor(1/16W 270Ω ± 5%)
Resistor(1/16W 270Ω ± 5%)
Resistor(1/16W 39KΩ ± 5%)
Resistor(1/16W 120KΩ ± 5%)
Resistor(1/16W 1KΩ ± 5%)
Resistor(1/16W 270Ω ± 5%)
Resistor(1/16W 150Ω ± 5%)
Resistor(1/16W 150Ω ± 5%)
Resistor(1/16W 0Ω ± 5%)
Resistor(1/16W 100Ω ± 5%)
Resistor(1/16W 270Ω ± 5%)
Resistor(1/16W 10KΩ ± 5%)
Resistor(1/16W 10KΩ ± 5%)
Resistor(1/16W 100KΩ ± 5%)
Block resistor(470Ω x4)
Block resistor(470Ω x4)
Block resistor(470Ω x4)
Block resistor(270Ω x4)
IC(S-814A33AUA)
Crystal(32.256MHz)
Crystal(32.768kHz)
Diode(1N4748A)
(02CZ180Y)
C
C
C
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
9
[L102]
[L103]
[L104]
[Q100]
[Q101]
[Q102]
[Q103]
[Q104]
[Q107]
[Q108]
[Q109]
[Q110]
[R100]
[R101]
[R102]
[R103]
[R104]
[R105]
[R106]
[R107]
[R111]
[R112]
[R113]
[R114]
[R116]
[R117]
[R118]
[R119]
[R120]
[R121]
[R124]
[R125]
[R126]
[R127]
[R128]
[R129]
[R130]
[R131]
[R132]
[R133]
[R134]
[R135]
[R136]
[R137]
[R139]
[R140]
[R141]
[R142]
[R143]
[R144]
[R145]
[R146]
[R147]
[R148]
[R149]
[R151]
[R152]
[R154]
[R156]
[R157]
[R160]
[R161]
[R165]
[R166]
[R167]
[R168]
[R169]
[R170]
[R171]
[R172]
[R173]
[R174]
[R175]
[R176]
[R177]
[R178]
[RA1]
[RA2]
[RA3]
[RA4]
[REG1]
[X1]
[X2]
[ZD1]
[ZD100]
UX-P115U
NO.
PARTS CODE
PRICE NEW PART
RANK MARK RANK
DESCRIPTION
[6] Control PWB unit
901
(Unit)
DCEKC688TXHZZ
BT
N
E
Control PWB unit(Within ROM)
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
B
B
B
B
B
C
C
C
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
Varistor(RA-391P-V6-2)
Varistor(RA501P-C6)
Capacitor(50WV 100µ F)
Capacitor(50WV 22µ F)
Capacitor(50WV 22µ F)
Capacitor(50WV 2.2µ F)
Capacitor(50WV 0.01µ F)
Capacitor(250WV 0.82µ F)
Capacitor(50WV 4.7µ F)
Capacitor(50WV 10µ F)
Capacitor(50WV 220PF)
Capacitor(50WV 0.1µ F)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(50WV 220PF)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(50WV 2200PF)
Relay(OUAZ-SH-124DZ)
Connector(12pin)
Diode(1N4148)
Diode(1N4148)
Diode(1N4148)
Diode(1N4148)
IC(LM2902NS)
Coil(K5A R6H 6x10(W)2.5TS)
Jack
Jack
Photo coupler(PC817X4)
Photo transistor(SG206S)
Photo transistor(SG206S)
Transistor(KTC3198GR)
Transistor(RT1N436C)
Transistor(RT1P141C)
Transistor(RT1N436C)
Transistor(RT1N436C)
Resistor(1/2W 100Ω ± 5%)
Resistor(1W 1.2KΩ ± 5%)
Resistor(1/2W 2KΩ ± 5%)
Resistor(1W 51Ω ± 5%)
Resistor(1/4W 100Ω ± 5%)
Resistor(1/4W 150Ω ± 5%)
Resistor(1/2W 22KΩ ± 5%)
Resistor(1/4W 22KΩ ± 5%)
Resistor(1/16W 3.3KΩ ± 5%)
Resistor(1/16W 620Ω ± 5%)
Resistor(1/16W 47KΩ ± 5%)
Resistor(1/16W 3.3KΩ ± 5%)
Resistor(1/16W 3.3KΩ ± 5%)
Resistor(1/16W 27KΩ ± 5%)
Resistor(1/16W 82KΩ ± 5%)
Resistor(1/16W 3.6KΩ ± 5%)
Resistor(1/16W 13KΩ ± 5%)
Resistor(1/16W 3.3KΩ ± 5%)
Resistor(1/16W 1KΩ ± 5%)
Resistor(1/16W 1KΩ ± 5%)
Resistor(1/16W 16KΩ ± 5%)
Resistor(1/16W 0Ω ± 5%)
Resistor(1/16W 56KΩ ± 5%)
Resistor(1/16W 39KΩ ± 5%)
Resistor(1/16W 3.3KΩ ± 5%)
Resistor(1/16W 8.2KΩ ± 5%)
Resistor(1/16W 13KΩ ± 5%)
Resistor(1/16W 3.3KΩ ± 5%)
Resistor(1/16W 220KΩ ± 5%)
Resistor(1/16W 0Ω ± 5%)
Resistor(1/16W 1.5KΩ ± 5%)
Resistor(1/16W 1KΩ ± 5%)
Hook switch
Transformer(2164)
Zener diode(HZ6A3)
Zener diode(HZ2C1)
Zener diode(HZ2C1)
Zener diode(HZ9C3)
Zener diode(HZ27)
E
TEL/LIU PWB unit
[7] TEL/LIU PWB unit
!
!
!
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
901
VHVRA391PV6-1
VHVRA501PC6-1
VCEAGA1HW107M
VCEAGA1HW226M
VCEAGA1HW226M
VCEAGA1HW225M
VCKYPA1HB103K
RC-FZ3024SCZZ
VCEAGA1HW475M
VCEAGA1HW106M
VCCCCY1HH221J
VCKYCY1HF104Z
VCKYCY1HB102K
VCKYCY1HB102K
VCKYCY1HB102K
VCKYCY1HB102K
VCCCCY1HH221J
VCKYCY1HB102K
VCCCCY1HH221J
VCKYCY1HB222K
RRLYD3433XHZZ
QCNCW715MAFZZ
VHD1N4148//-1
VHD1N4148//-1
VHD1N4148//-1
VHD1N4148//-1
RH-IX2383XHZZ
RCILZ2129SCZZ
QJAKZ2060SC0B
QJAKZ2079XH0D
VHPPC817X4/-1
VHPSG206S//-1
VHPSG206S//-1
VSKTC3198GR-1
VSRT1N436C/-1
VSRT1P141C+-1
VSRT1N436C/-1
VSRT1N436C/-1
VRS-RE2HA101J
VRS-RE3AA122J
VRD-HT2HY202J
VRS-HT3AA510J
VRD-HT2EY101J
VRD-HT2EY151J
VRD-HT2HY223J
VRD-HT2EY223J
VRS-CY1JB332J
VRS-CY1JB621J
VRS-CY1JB473J
VRS-CY1JB332J
VRS-CY1JB332J
VRS-CY1JB273J
VRS-CY1JB823J
VRS-CY1JB362J
VRS-CY1JB133J
VRS-CY1JB332J
VRS-CY1JB102J
VRS-CY1JB102J
VRS-CY1JB163J
VRS-CY1JB000J
VRS-CY1JB563J
VRS-CY1JB393J
VRS-CY1JB332J
VRS-CY1JB822J
VRS-CY1JB133J
VRS-CY1JB332J
VRS-CY1JB224J
VRS-CY1JB000J
VRS-CY1JB152J
VRS-CY1JB102J
QSW-Z2317XHZZ
RTRNI2164XHZZ
VHEHZ6A3///-1
VHEHZ2C1///-1
VHEHZ2C1///-1
VHEHZ9C3///-1
VHEHZ27-1//-1
(Unit)
DCEKL477CXH02
AE
AG
AA
AB
AB
AA
AA
AG
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AH
AF
AA
AA
AA
AA
AG
AE
AD
AD
AC
AG
AG
AD
AD
AB
AD
AD
AB
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AF
AG
AC
AA
AA
AE
AB
BG
N
10
[AR1]
[AR3]
[C1]
[C2]
[C3]
[C4]
[C5]
[C6]
[C7]
[C8]
[C100]
[C101]
[C103]
[C104]
[C105]
[C106]
[C109]
[C110]
[C111]
[C114]
[CML]
[CNLIUA]
[D1]
[D2]
[D3]
[D4]
[IC100]
[L3]
[MJ1]
[MJTEL]
[PC1]
[PH1]
[PH2]
[Q1]
[Q100]
[Q101]
[Q102]
[Q103]
[R1]
[R2]
[R3]
[R4]
[R5]
[R6]
[R7]
[R8]
[R100]
[R101]
[R102]
[R103]
[R104]
[R105]
[R106]
[R107]
[R108]
[R109]
[R110]
[R111]
[R112]
[R113]
[R114]
[R115]
[R116]
[R117]
[R118]
[R119]
[R120]
[R122]
[R123]
[R124]
[SW1]
[T1]
[ZD2]
[ZD3]
[ZD4]
[ZD5]
[ZD6]
UX-P115U
NO.
PARTS CODE
PRICE NEW PART
RANK MARK RANK
DESCRIPTION
[8] Power supply PWB unit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
!
901
0CBUGFM224KR/
0CBUGA0291ZZ/
0CBUGCU471EL/
0CBUGXJQF102/
0CBUGXHWF153/
0CBUEXBAF000/
0CBUGA0315ZZ/
0CBUGA0302ZZ/
0CBUGXJXD104/
0CBUGCS222AJ/
0CBUGXHPF391/
0CBUGCM103BH/
0CBUGCM103BH/
0CBUGCU472BW/
0CBPKZ0194ZZ/
0CBPCZ0307ZZ/
0CBUBF0002AK/
0CBUBF0002AK/
0CBUBF0002AK/
0CBUBF0002AK/
0CBUBA0003BL/
0CBUBC0336AZ/
0CBUBC0070AM/
0CBUBC0169CL/
0CBPJCEJ3151/
0CBPZZ1008ZZ/
0CBBFZ89902Z/
0CBBFZ89633Z/
0CBUKZ1186ZZ/
0CBUZZ0213ZZ/
0CBLRZ6987ZA/
0CBUDC0062MZ/
0CBUAG0213AC/
0CBUAC0255AM/
0CBUAC0264AK/
0CBUAC0034EL/
0CBUEXDAW334/
0CBUEXDAW474/
0CBUEXDAW474/
0CBUEEB681CT/
0CBUEXCAP272/
0CBUEXBAF183/
0CBUEXBAF181/
0CBUEXBAF473/
0CBUEXBAF470/
0CBUEFDR15DB/
0CBUEXDAW334/
0CBUEXDAW334/
0CBUEEB472CT/
0CBUEXCAP102/
0CBUEXBAF334/
0CBUEXBAF103/
0CBUEXBAF332/
0CBUEEB332CT/
0CBUEEB682CT/
0CBUEEB682CT/
0CBUEEB682CT/
0CBUEFE104DS/
0CB829653001/
0CBUEZ0666ZZ/
0CBUFBA222EQ/
0CBUBDQR270A/
0CBUBDBE4R3C/
0CBUBDDA300A/
0CBUBDBE6R2C/
0CBUBDBE100C/
0CBUBDBE9R1C/
(Unit)
RDENT2198XHZZ
AF
AC
AF
AC
AF
AC
AL
AK
AD
AD
AD
AD
AD
AD
AC
AD
AD
AD
AD
AD
AD
AL
AG
AE
AH
AH
AD
AD
AH
AN
AQ
AG
AK
AD
AD
AD
AC
AC
AC
AC
AC
AC
AC
AC
AC
AE
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AE
BF
AD
AD
AD
AD
AE
AC
AE
AD
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
A
A
C
C
C
C
C
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
C
B
B
B
B
B
B
Capacitor(275WV 0.22µ F)
Capacitor(200WV 220µ F)
Capacitor(1KWV 470PF)
Capacitor(50WV 1000PF)
Capacitor(50WV 0.015µ F)
Resistor(1/16W 0Ω ± 5%)
Capacitor(35WV 560µ F)
Capacitor(16WV 330µ F)
Capacitor(25WV 0.1µ F)
Capacitor(500WV 2200PF)
Capacitor(50WV 390PF)
Capacitor(250WV 0.01µ F)
Capacitor(250WV 0.01µ F)
Capacitor(1KWV 4700PF)
Base post ass'y(B 2P3-VH)
Connector(IMSA-9110S-06)
Diode(10EDB60)
Diode(10EDB60)
Diode(10EDB60)
Diode(10EDB60)
Diode(1S2076A)
Diode(S3L20U)
Diode(ERA81-004V3)
Diode(ERA22-06V3)
Fuse(3.15A/AC125V)
Circuit protector(4A/32V)
Beads core(3A)
Beads inductor(BP53RB052025050)
Filter(33mH/0.5A)
Inductor(RS912)
Heat sink(MN210-5001AT)
Photo coupler(PS2501-1L)
FET(2SK3306)
Transistor(2SC4115S)
Transistor(2SC1741AS)
Transistor(2SC1740S)
Resistor(1/4W 330KΩ ± 5%)
Resistor(1/4W 470KΩ ± 5%)
Resistor(1/4W 470KΩ ± 5%)
Resistor(1/4W 680Ω ± 5%)
Resistor(1/10W 2.7KΩ ± 5%)
Resistor(1/16W 18KΩ ± 5%)
Resistor(1/16W 18KΩ ± 5%)
Resistor(1/16W 47KΩ ± 5%)
Resistor(1/16W 47Ω ± 5%)
Metal film resistor(1W 0.15Ω ± 5%)
Resistor(1/4W 330KΩ ± 5%)
Resistor(1/4W 330KΩ ± 5%)
Resistor(1/4W 4.7KΩ ± 5%)
Resistor(1/16W 1KΩ ± 5%)
Resistor(1/16W 330KΩ ± 5%)
Resistor(1/16W 10KΩ ± 5%)
Resistor(1/16W 3.3KΩ ± 5%)
Resistor(1/4W 3.3KΩ ± 5%)
Resistor(1/4W 6.8KΩ ± 5%)
Resistor(1/4W 6.8KΩ ± 5%)
Resistor(1/4W 6.8KΩ ± 5%)
Metal film resistor(2W 100KΩ ± 5%)
Transformer(PTTN146-KTT)
Varistor(S07K150GA)
Variable resistor(2.2KΩ )
Zener diode(27HSB-26)
Zener diode(RD4.3SAB)
Zener diode(HZ30CPTK)
Zener diode(RD6.2SAB2-T1)
Zener diode(RD10ESAB-T1)
Zener diode(RD9.1ESAB2-T1)
BG
E
Power supply PWB unit
AE
AH
AE
C
C
C
Tact switch
FRSNS sensor
ORGSNS sensor
BG
E
Operation panel PWB unit
[C1]
[C2]
[C3]
[C4]
[C5]
[C6]
[C8]
[C10]
[C12]
[C13]
[C24]
[C26]
[C27]
[C31]
[CNAC]
[CNPS]
[D1]
[D2]
[D3]
[D4]
[D5]
[D7]
[D8]
[D9]
[F1]
[F3]
[FB2]
[FB3]
[L1]
[L2]
[MT2]
[PC1]
[Q1]
[Q2]
[Q3]
[Q4]
[R1]
[R2]
[R3]
[R4]
[R5]
[R6]
[R7]
[R8]
[R9]
[R10]
[R11]
[R12]
[R13]
[R14]
[R15]
[R16]
[R17]
[R18]
[R27]
[R28]
[R29]
[R30]
[T1]
[V1]
[VR1]
[ZD1]
[ZD2]
[ZD4]
[ZD5]
[ZD8]
[ZD9]
[9] Operation panel PWB unit
!
!
1
2
3
901
QSW-Q2331XHZZ
QSW-M2246AXZZ
QSW-M2294XHZZ
(Unit)
DCEKP478CXH02
11
[SW]
UX-P115U
„INDEX
INDEX
PARTS CODE
[ C
CCNWN395BXH01
CGERH2314XH05
CGERH2566XH01
CLEVP2358XH01
CLEVP2359XH01
CLEVP2360XH01
CLEVP2361XH01
CLEVP2362XH01
CPAKC271GXH01
CPLTP3183XHRF
CPLTP3222XHR2
CROLR2481XH01
[ D
DCEKC688TXHZZ
"
DCEKL477CXH02
"
DCEKP478CXH02
"
DCEKP480CXH02
DUNTK497CXHFW
[ G
GCABB2393XHSH
GCASP2173XHSA
GCOVA2447XHVA
GCOVA2448XHVA
GLEGG2078XHZZ
[ H
HPNLH2420XHSN
"
[ J
JBTN-2357XHSB
JBTN-2358XHSC
JBTN-2359XHSD
JBTN-2360XHSC
JBTN-2361XHSD
No.
PRICE NEW PART
RANK MARK RANK
PARTS CODE
MSPRC3346XHZZ
MSPRC3357XHZZ
MSPRD3285XHZZ
MSPRD3286XHZA
MSPRD3291XHZZ
MSPRD3292XHZA
MSPRD3293XHZZ
MSPRD3298XHZZ
MSPRD3302XHZZ
MSPRD3341XHZZ
MSPRD3379XHZZ
MSPRP3297XHZZ
MSPRT3294XHZZ
[ N ]
NGERH2380XHZZ
NGERH2409XHZZ
NGERH2568XHZZ
NGERH2569XHZZ
NGERH2570XHZZ
NGERH2571XHZZ
NGERH2572XHZZ
NGERH2573XHZZ
NGERH2574XHZZ
NGERH2575XHZZ
NGERH2576XHZZ
NGERH2577XHZZ
NGERH2579XHZA
NGERH2580XHZZ
NGERH2581XHZZ
NGERH2582XHZZ
NGERP2318XHZZ
NROLP2332XHZZ
NROLR2482XHZZ
NROLR2483XHZZ
NROLR2485XHZZ
NROLR2504XHZZ
NSFTP2357XHZZ
NSFTP2374XHZZ
]
1-3
4-1
5-21
1-4
4-2
4-3
4-4
4-5
5-17
5-20
5-3
1-5
AP
AS
AG
AD
AD
AD
AD
AD
AV
AV
AQ
AQ
1-6
6-901
1-7
7-901
3-5
9-901
3-901
5-1
BT
BT
BG
BG
BG
BG
BG
AY
1-35
3-1
1-46
2-1
1-47
AZ
BA
AL
AX
AD
1-62
3-21
AM
AM
3-2
3-4
3-3
3-18
3-19
AK
AP
AQ
AH
AM
C
C
C
C
C
1-17
2-29
1-22
1-23
2-25
2-26
1-24
4-6
2-6
2-7
2-18
1-36
1-37
3-11
2-19
1-48
4-7
3-12
3-13
1-49
2-20
2-21
2-22
2-B3
2-B1
1-B3
1-W2
AA
AA
AC
AC
AE
AE
AP
AQ
AQ
AT
AL
AD
AD
AE
AD
AF
AG
AD
AD
AD
AD
AH
AH
AC
AD
AB
AE
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
4-8
1-51
1-50
2-8
1-38
1-39
1-25
2-23
2-24
2-2
2-9
2-30
1-40
AE
AD
AD
AD
AB
AB
AB
AB
AB
AB
AB
AD
AD
C
C
C
C
C
C
C
C
C
C
C
C
C
N
N
C
C
C
C
C
C
C
C
D
C
C
C
]
N
N
E
E
E
E
E
E
E
E
]
D
D
D
C
C
]
N
N
D
D
]
[ L ]
LBNDJ2006XHZZ
"
LBSHP2140XHZA
LBSHP2143XHZZ
LBSHP2148XHZA
LBSHP2149XHZA
LFRM-2225XHVA
LFRM-2226XHZZ
LFRM-2227XHZZ
LFRM-2232XHZZ
LHLDZ2224XHZZ
LHLDZ2227XHZZ
LHLDZ2228XHZZ
LPLTG2911XHZZ
LPLTG3181XHZZ
LPLTM3178XHZZ
LPLTM3190XHZZ
LPLTP3175XHZZ
LPLTP3176XHZZ
LPLTP3177XHZZ
LPLTP3179XHZZ
LPLTP3180XHZZ
LPLTP3182XHZZ
LX-BZ2222XHZZ
LX-BZ2234XHZZ
LX-BZ2282XHZZ
LX-WZ2290XHZZ
[ M ]
MCAMP2028XHZZ
MLEVP2356XHZA
MLEVP2357XHZZ
MLEVP2363XHZZ
MSPRC3287XHZZ
MSPRC3288XHZZ
MSPRC3295XHZZ
MSPRC3299XHZZ
MSPRC3300XHZZ
MSPRC3301XHZZ
MSPRC3305XHZZ
MSPRC3335XHZZ
MSPRC3340XHZA
[ P ]
PBRS-2055XHZZ
PCOVP2130XHZZ
PCOVP2131XHVA
PCOVP2132XHZZ
PGIDM2614XHSA
PGIDM2615XHZZ
PGIDM2616XHZZ
PGIDM2617XHZZ
PGIDM2618XHZZ
PGIDM2619XHVA
PGIDM2620XHVA
PGIDM2621XHSA
PRBNN2038SC10
PSHEP3660XHZZ
PSHEZ3687XHZZ
[ Q ]
QACCD2090XHZZ
QCNCM2508SC1B
QCNCM2638SC0F
QCNCM2666XH0C
QCNCM2666XH0G
QCNCM2666XH1F
QCNCM7014SC0B
QCNCM7014SC0C
QCNCM7014SC0F
QCNCM7014SC1E
QCNCW715MAFZZ
QCNWG209BXHOW
QCNWG370BXHZZ
QCNWN399BXHZZ
"
QCNWN419BXHZZ
QCNWN483AXHZZ
QCNWN486AXHZZ
QFS-L1037YCZZ
QJAKZ2060SC0B
QJAKZ2079XH0D
QPWBF3368XHZ2
QSW-F2224SCZZ
QSW-M2246AXZZ
12
No.
PRICE NEW PART
RANK MARK RANK
1-66
1-67
1-53
1-52
1-54
1-55
3-14
4-9
2-10
1-65
1-26
4-23
3-15
AD
AD
AB
AB
AD
AB
AB
AE
AB
AD
AD
AD
AB
C
C
C
C
C
C
C
C
C
C
C
C
C
4-10
4-11
5-4
1-27
1-28
4-12
4-13
4-14
4-15
4-16
4-17
4-18
2-27
2-11
2-12
4-19
2-3
1-29
1-30
2-13
2-28
2-14
2-15
2-16
AC
AB
AB
AC
AD
AD
AD
AD
AD
AD
AD
AD
AE
AC
AC
AC
AD
AD
AR
AL
AQ
AL
AG
AG
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
1-63
1-41
1-57
1-58
3-16
1-42
1-43
1-31
1-32
2-4
2-5
2-17
5-5
3-17
1-64
AN
AE
AG
AD
AL
AD
AD
AD
AD
AG
AG
AF
AL
AE
AD
C
C
C
C
C
C
C
C
C
C
C
C
S
C
C
1-59
6-83
6-87
6-88
6-81
6-85
6-82
6-86
6-84
6-89
7-22
5-2
5-6
1-16
3-9
1-33
4-20
1-44
6-93
7-29
7-30
1-8
4-21
3-7
AS
AF
AE
AD
AE
AF
AD
AA
AB
AC
AF
AH
AL
AP
AP
AL
AD
AM
AD
AD
AD
AQ
AE
AH
N
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
A
C
C
E
C
C
UX-P115U
PARTS CODE
"
QSW-M2294XHZZ
"
QSW-Q2331XHZZ
"
QSW-Z2317XHZZ
[ R
RC-FZ3024SCZZ
RCILZ2129SCZZ
RCRSB0297AFZZ
RCRSP2176SCZZ
RDENT2198XHZZ
"
RHEDZ2065XHZZ
RH-IX2321XHZZ
RH-IX2356XHZZ
RH-IX2357XHZZ
RH-IX2383XHZZ
RMOTS2175XHZZ
RRLYD3433XHZZ
RR-TZ3017SCZZ
RR-TZ3018SCZZ
"
"
RTRNI2164XHZZ
RUNTZ2127XH01
RUNTZ2127XHZZ
[ S
SPAKA465CXHZZ
SPAKA466CXHZZ
SPAKA467CXHZZ
SPAKP329DXHZZ
[ T
TCADZ2891XHZZ
TCADZ3744XHZZ
TCADZ3745XHZZ
TINSE4463XHTZ
TLABH498FXHZZ
[ U
UBATL2049SCZZ
[ V
VCCCCY1HH101J
"
"
"
"
"
"
"
"
"
"
"
"
"
"
VCCCCY1HH150J
VCCCCY1HH220J
"
VCCCCY1HH221J
"
"
"
VCCCCY1HH330J
VCEAGA0JW227M
"
VCEAGA1EW476M
"
VCEAGA1HW106M
"
"
"
"
VCEAGA1HW107M
VCEAGA1HW225M
VCEAGA1HW226M
"
"
VCEAGA1HW475M
VCKYCY1AB105K
"
"
No.
PRICE NEW PART
RANK MARK RANK
9-2
3-8
9-3
3-6
9-1
7-71
AH
AE
AE
AE
AE
AF
C
C
C
C
C
C
7-8
7-28
6-182
6-181
1-61
8-901
1-45
6-95
6-98
6-180
7-27
4-22
7-21
6-179
6-176
6-177
6-178
7-72
3-10
1-34
AG
AE
AD
AG
BG
BG
BP
AX
AL
AH
AG
AX
AH
AC
AC
AC
AC
AG
BC
C
C
B
B
E
E
B
B
B
B
B
B
B
B
B
B
B
B
E
B
5-14
5-15
5-16
5-18
AF
AF
AD
AF
5-23
5-24
5-12
5-11
1-68
AF
AL
AL
BC
AH
6-1
AF
B
6-13
6-14
6-19
6-20
6-21
6-23
6-24
6-60
6-62
6-63
6-71
6-72
6-73
6-74
6-75
6-29
6-51
6-52
6-37
7-11
7-17
7-19
6-28
6-2
6-4
6-3
6-7
6-5
6-6
6-8
6-9
7-10
7-3
7-6
6-10
7-4
7-5
7-9
6-55
6-56
6-66
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AD
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
AA
AB
AB
AB
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
]
N
N
N
]
D
D
D
D
]
N
N
N
D
D
D
D
D
]
]
PARTS CODE
VCKYCY1AF105Z
"
"
"
"
"
"
"
"
"
"
"
"
VCKYCY1CB104K
"
"
VCKYCY1HB102K
"
"
"
"
"
"
"
"
"
"
VCKYCY1HB103K
"
VCKYCY1HB222K
VCKYCY1HB471K
VCKYCY1HB472K
VCKYCY1HF104Z
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
VCKYPA1HB103K
VHD1N4148//-1
"
"
"
VHD1SS355//-1
"
VHDHRW0202B-1
VHE02CZ180Y-1
VHE1N4748A/-1
VHEHZ27-1//-1
VHEHZ2C1///-1
"
VHEHZ6A3///-1
VHEHZ9C3///-1
VHIF002/TC89B
VHINJM2113M-1
VHISCE209//-1
VHPPC817X4/-1
VHPSG206S//-1
"
VHVRA391PV6-1
VHVRA501PC6-1
VRD-HT2EY101J
VRD-HT2EY151J
VRD-HT2EY223J
VRD-HT2HY202J
VRD-HT2HY223J
13
No.
6-35
6-36
6-38
6-39
6-42
6-45
6-46
6-47
6-48
6-49
6-50
6-58
6-59
6-65
6-68
6-69
6-11
6-12
6-57
6-76
6-77
6-78
7-13
7-14
7-15
7-16
7-18
6-26
6-30
7-20
6-79
6-31
6-15
6-16
6-17
6-18
6-22
6-25
6-27
6-32
6-33
6-34
6-40
6-41
6-43
6-44
6-53
6-54
6-61
6-64
6-70
6-80
6-150
7-12
7-7
7-23
7-24
7-25
7-26
6-91
6-92
6-90
6-184
6-183
7-77
7-74
7-75
7-73
7-76
6-94
6-97
6-96
7-31
7-32
7-33
7-1
7-2
7-43
7-44
7-46
7-41
7-45
PRICE NEW PART
RANK MARK RANK
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AD
AC
AC
AB
AA
AA
AC
AE
BD
AG
BH
AC
AG
AG
AE
AG
AA
AA
AA
AA
AA
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
UX-P115U
PARTS CODE
VRS-CY1JB000J
"
"
"
"
"
"
"
"
"
"
VRS-CY1JB101J
VRS-CY1JB102J
"
"
"
"
"
"
"
"
"
"
VRS-CY1JB103J
"
"
"
"
"
"
"
VRS-CY1JB104J
"
VRS-CY1JB105J
"
VRS-CY1JB106J
VRS-CY1JB124J
"
VRS-CY1JB133J
"
VRS-CY1JB150J
VRS-CY1JB151J
"
"
VRS-CY1JB152J
VRS-CY1JB163J
VRS-CY1JB203J
"
"
"
VRS-CY1JB222J
VRS-CY1JB223J
VRS-CY1JB224J
"
"
VRS-CY1JB271J
"
"
"
"
"
"
"
"
"
"
VRS-CY1JB273J
VRS-CY1JB301J
VRS-CY1JB332J
"
"
"
"
"
VRS-CY1JB362J
VRS-CY1JB392J
VRS-CY1JB393J
"
VRS-CY1JB471J
"
"
"
No.
6-67
6-99
6-100
6-101
6-115
6-123
6-140
6-152
6-170
7-60
7-68
6-171
6-121
6-125
6-134
6-135
6-137
6-138
6-151
6-166
7-57
7-58
7-70
6-119
6-129
6-131
6-141
6-148
6-149
6-173
6-174
6-139
6-175
6-133
6-158
6-147
6-126
6-165
7-55
7-65
6-102
6-130
6-168
6-169
7-69
7-59
6-124
6-127
6-143
6-153
6-156
6-155
6-128
6-144
7-67
6-113
6-114
6-120
6-146
6-154
6-160
6-161
6-162
6-163
6-167
6-172
7-52
6-136
7-47
7-50
7-51
7-56
7-63
7-66
7-54
6-157
6-164
7-62
6-116
6-117
6-118
6-132
PRICE NEW PART
RANK MARK RANK
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
PARTS CODE
VRS-CY1JB473J
VRS-CY1JB474J
VRS-CY1JB512J
VRS-CY1JB513J
VRS-CY1JB562J
VRS-CY1JB563J
VRS-CY1JB621J
VRS-CY1JB752J
VRS-CY1JB822J
VRS-CY1JB823J
VRS-HT3AA510J
VRS-RE2HA101J
VRS-RE3AA122J
VS2SA1530AS-1
VSKTC3198GR-1
VSRT1N141C/-1
"
"
"
"
"
VSRT1N436C/-1
"
"
VSRT1P141C+-1
"
VSSI4431BDY-1
[ X ]
XEBSD20P06000
XEBSD30P08000
XEBSD30P10000
"
XEBSD30P12000
XEPSD30P08000
XWHSN40-08100
[ 0 ]
0CB829653001/
0CBBFZ89633Z/
0CBBFZ89902Z/
0CBLRZ6987ZA/
0CBPCZ0307ZZ/
0CBPJCEJ3151/
0CBPKZ0194ZZ/
0CBPZZ1008ZZ/
0CBUAC0034EL/
0CBUAC0255AM/
0CBUAC0264AK/
0CBUAG0213AC/
0CBUBA0003BL/
0CBUBC0070AM/
0CBUBC0169CL/
0CBUBC0336AZ/
0CBUBDBE100C/
0CBUBDBE4R3C/
0CBUBDBE6R2C/
0CBUBDBE9R1C/
0CBUBDDA300A/
0CBUBDQR270A/
0CBUBF0002AK/
"
"
"
0CBUDC0062MZ/
0CBUEEB332CT/
0CBUEEB472CT/
0CBUEEB681CT/
0CBUEEB682CT/
"
"
0CBUEFDR15DB/
0CBUEFE104DS/
0CBUEXBAF000/
0CBUEXBAF103/
0CBUEXBAF181/
0CBUEXBAF183/
0CBUEXBAF332/
0CBUEXBAF334/
0CBUEXBAF470/
0CBUEXBAF473/
0CBUEXCAP102/
0CBUEXCAP272/
0CBUEXDAW334/
14
No.
PRICE NEW PART
RANK MARK RANK
7-49
6-142
6-122
6-145
6-112
7-61
7-48
6-159
7-64
7-53
7-42
7-39
7-40
6-103
7-34
6-104
6-105
6-106
6-107
6-110
6-111
7-35
7-37
7-38
6-109
7-36
6-108
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AA
AB
AC
AC
AD
AB
AB
AB
AB
AB
AB
AD
AD
AD
AB
AB
AL
3-B1
4-B1
1-B1
2-B2
1-B2
1-B4
1-W1
AA
AA
AA
AA
AA
AA
AA
C
C
C
C
C
C
C
8-59
8-28
8-27
8-31
8-16
8-25
8-15
8-26
8-36
8-34
8-35
8-33
8-21
8-23
8-24
8-22
8-66
8-63
8-65
8-67
8-64
8-62
8-17
8-18
8-19
8-20
8-32
8-54
8-49
8-40
8-55
8-56
8-57
8-46
8-58
8-6
8-52
8-43
8-42
8-53
8-51
8-45
8-44
8-50
8-41
8-37
BF
AD
AD
AQ
AD
AH
AC
AH
AD
AD
AD
AK
AD
AG
AE
AL
AE
AD
AC
AD
AE
AD
AD
AD
AD
AD
AG
AC
AC
AC
AC
AC
AC
AE
AE
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
B
C
C
C
C
A
C
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
N
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
UX-P115U
PARTS CODE
"
"
0CBUEXDAW474/
"
0CBUEZ0666ZZ/
0CBUFBA222EQ/
0CBUGA0291ZZ/
0CBUGA0302ZZ/
0CBUGA0315ZZ/
0CBUGCM103BH/
"
0CBUGCS222AJ/
0CBUGCU471EL/
0CBUGCU472BW/
0CBUGFM224KR/
0CBUGXHPF391/
0CBUGXHWF153/
0CBUGXJQF102/
0CBUGXJXD104/
0CBUKZ1186ZZ/
0CBUZZ0213ZZ/
No.
8-47
8-48
8-38
8-39
8-60
8-61
8-2
8-8
8-7
8-12
8-13
8-10
8-3
8-14
8-1
8-11
8-5
8-4
8-9
8-29
8-30
PRICE NEW PART
RANK MARK RANK
AC
AC
AC
AC
AD
AD
AC
AK
AL
AD
AD
AD
AF
AD
AF
AD
AF
AC
AD
AH
AN
C
C
C
C
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
15
UX-P115U
COPYRIGHT © 2004
XXXXBY
BYSHARP
COPYRIGHT
SHARP CORPORATION
CORPORATION
ALL RIGHTS
ALL
RIGHTS RESERVED.
RESERVED.
No part
No
part of
of this
this publication
publication may
may be
be reproduced,
reproduced,
stored
in
a
retrieval
system,
or
transmitted
stored in a retrieval system, or transmitted in
in
any form
any
form or
or by
by any
any means,
means, electronic,
electronic, mechanical,
mechanical,
photocopying, recording,
photocopying,
recording, or
or otherwise,
otherwise, without
without
prior written
prior
written permission
permission of
of the
the publisher.
publisher.
SHARP CORPORATION
Communication Systems Group
Quality & Reliability Control Center
Higashihiroshima, Hiroshima 739-0192, Japan
A0407-DS•IS•T