CSD-ED79 EZ(S)
SERVICE MANUAL
COMPACT DISC STEREO
CASSETTE RECORDER
BASIC TAPE MECHANISM : TN21ZVC-1816
BASIC CD MECHANISM : KSM-213CDM
S/M Code No. 09-994-329-8R1
DA
TA
RE
VI
SIO
N
This Service Manual is the “Revision Publishing” and replaces “Simple Manual”
CSD-ED79(EZ<S>)(S/M Code No.09-994-329-8T1).
SPECIFICATIONS
<Compact disc player section>
<Tuner section>
(FM)
Tuning range
Antenna
Disk
Scanning method
87.5 MHz to 108.0 MHz
Rod antenna
Compact disc
Non-contact optical scanner
(Semicondactor laser)
<General>
(MW)
Tuning range
Speakers
522 kHz to 1611 kHz (9 kHz step)
530 kHz to 1710 kHz (10 kHz step)
Ferrite bar antenna
Antenna
Power output
(LW)
Tuning range
Antenna
153 kHz to 288 kHz
Ferrite bar antenna
Output
Power requirements
<Cassette deck section>
Track format
Frequency response
Recording system
Erasing system
Heads
4 track, 2 channels stereo
Normal tape: 50 Hz - 12500 Hz
AC bias
Magnet erase
Recording/Playback head x 1
Erasure head x 1
Power consumption
Dimensions of main unit
Weight of main unit
100 mm cone type (2)
36 mm cone type (2)
5.0 W + 5.0 W
(DIN MUSIC POWER)
4.5 W + 4.5 W
(EIAJ 3.2 ohms, T.H.D. 10 %)
3.3 W + 3.3 W
(DIN 1 % Rated Power)
Headphones (stereo minijack)
DC 12 V using eight size C (R14)
batteries
AC 230 V
50 Hz
27 W
(W x H x D)
507 x 206 x 299.5 mm
4.7 kg
• Design and specifications are subject to change without notice.
ACCESSORIES LIST
REF. NO
PART NO.
KANRI
NO.
1 8Z-CH4-908-010
! 2 87-A80-036-010
DESCRIPTION
IB,EZ(9L)B
AC CORD SET ASSY,E W/FLTR VOL
2
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the
instructions below when servicing.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 30cm FROM THE
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL
PICK-UP BLOCK.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que
ceux spécifiés peut entraîner une dangereuse exposition aux
radiations.
ADVARSEL!
Caution: Invisible laser radiation when
open and interlocks defeated avoid exposure to beam.
Advarsel:Usynling laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
VARNING!
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling
laserstrålning, som överskrider gränsen för laserklass 1.
Precaution to replace Optical block
(KSS – 213B)
CD PICK-UP ASSY P.C.B.
Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.
1) After the connection, remove solder shown in
the right figure.
Solder
3
ELECTRICAL MAIN PARTS LIST
REF. NO
PART NO.
KANRI
NO.
DESCRIPTION
REF. NO
IC
87-A20-459-010
8Z-CH4-636-010
87-A21-184-010
87-A21-185-040
87-A20-946-040
C-IC,LC78622ED
IC,LC867132V-5K36
IC,TA2104AN
C-IC,LC72121M
C-IC,MM1434XF
87-A20-591-010
87-A21-111-040
87-070-416-010
87-A20-446-010
87-A21-093-010
IC,BA5417
C-IC,M62495FP
IC,NJU7201 L55
C-IC,LA9241ML
IC,LA6541D
87-A21-145-040
C-IC,BA4560F-E2
87-026-291-010
89-213-702-010
89-319-233-080
87-A30-092-080
87-026-447-080
TR,DTC124XS
TR,2SB1370E(1.8W)
TR,2SC1923 (0.1W)
FET,2SK439E/F
TR,2SC1740S R
89-320-011-080
87-026-214-080
87-026-215-010
89-112-965-010
87-026-463-010
TR,2SC2001K(15W)
TR,DTA114YS (0.3W)
TR,DTC114YS
TR,2SA1296GR
TR,2SA933S,RS
87-026-462-010
89-113-184-080
89-112-965-080
87-026-464-010
87-026-239-010
TR,2SC1740SRS
TR,2SA1318TU
TR,2SA1296GR(0.75W)
TR,DTC114TS
TR,DTC114TK
89-318-154-010
89-318-155-010
87-026-496-080
88-NF9-637-010
89-110-150-010
TR,2SC1815Y
TR,2SC1815(GR)
FET,2SJ103GR
TR,2SA1318T/U
TR,2SA1015
PART NO.
KANRI
NO.
DESCRIPTION
C22
C24
C25
C26
C27
87-010-197-080
87-012-157-080
87-016-460-080
87-010-322-080
87-A11-067-080
CAP, CHIP 0.01 DM
C-CAP 330P-50CH
C-CAP,S 0.22-16 B
C-CAP,S 100P-50
C-CAP,S 1-10 K B
C28
C29
C30
C31
C33
87-016-669-080
87-016-669-080
87-010-220-080
87-010-220-080
87-010-401-080
C-CAP,S 0.1-25 K
C-CAP,S 0.1-25 K
C-CAP,S 0.018-25
C-CAP,S 0.018-25
CAP, ELECT 1-50V
C34
C35
C36
C37
C38
87-010-401-080
87-015-819-080
87-010-112-080
87-010-197-080
87-010-380-080
CAP, ELECT 1-50V
CAPACITOR,0.01
CAP, ELECT 100-16V
CAP, CHIP 0.01 DM
CAP, ELECT 47-16V
C39
C40
C41
C42
C43
87-010-404-080
87-010-197-080
87-012-349-080
87-012-349-080
87-012-349-080
CAP, ELECT 4.7-50V
CAP, CHIP 0.01 DM
C-CAP,S 1000P-50 CH
C-CAP,S 1000P-50 CH
C-CAP,S 1000P-50 CH
C44
C45
C46
C47
C48
87-010-311-080
87-010-312-080
87-010-197-080
87-010-197-080
87-010-197-080
C-CAP,S 12P-50
C-CAP,S 15P-50
CAP, CHIP 0.01
CAP, CHIP 0.01
CAP, CHIP 0.01
C49
C50
C51
C52
C53
87-012-156-080
87-010-197-080
87-010-316-080
87-010-197-080
87-010-197-080
C-CAP,S 220P-50 CH
CAP, CHIP 0.01 DM
C-CAP,S 33P-50 CH
CAP, CHIP 0.01 DM
CAP, CHIP 0.01 DM
C54
C55
C71
C72
C73
87-014-055-080
87-010-197-080
87-010-197-080
87-016-669-080
87-016-669-080
CAP,PP 820P-100 J
CAP, CHIP 0.01 DM
CAP, CHIP 0.01 DM
C-CAP,S 0.1-25 K B
C-CAP,S 0.1-25 K B
C78
C207
C208
C209
C210
87-016-669-080
87-010-408-080
87-010-402-080
87-010-190-080
87-010-190-080
C-CAP,S 0.1-25 K B
CAP, ELECT 47-50V
CAP, ELECT 2.2-50V
S CHIP F 0.01
S CHIP F 0.01
C211
C212
C215
C216
C217
87-010-401-080
87-010-401-080
87-010-425-080
87-010-425-080
87-010-400-080
CAP, ELECT 1-50V
CAP, ELECT 1-50V
C-CAP,0.22-25 F
C-CAP,0.22-25 F
CAP, ELECT 0.47-50V
C218
C220
C222
C223
C226
87-010-400-080
87-010-405-080
87-010-190-080
87-010-190-080
87-010-190-080
CAP, ELECT 0.47-50V
CAP, ELECT 10-50V
S CHIP F 0.01
S CHIP F 0.01
S CHIP F 0.01
C228
C229
C231
C232
C233
87-010-401-080
87-010-401-080
87-010-213-080
87-010-213-080
87-010-546-080
CAP, ELECT 1-50V
CAP, ELECT 1-50V
C-CAP,S 0.015-50 B
C-CAP,S 0.015-50 B
CAP, ELECT 0.33-50V
C234
C235
C236
C237
C238
87-010-546-080
87-010-544-080
87-010-544-080
87-010-260-080
87-010-263-080
CAP,
CAP,
CAP,
CAP,
CAP,
ELECT
ELECT
ELECT
ELECT
ELECT
0.33-50V
0.1-50V
0.1-50V
47-25V
100-10V
C241
C242
C243
C244
C245
87-010-405-080
87-010-405-080
87-010-405-080
87-010-405-080
87-010-405-080
CAP,
CAP,
CAP,
CAP,
CAP,
ELECT
ELECT
ELECT
ELECT
ELECT
10-50V
10-50V
10-50V
10-50V
10-50V
C246
C247
C248
C261
C262
87-010-405-080
87-010-404-080
87-010-404-080
87-010-402-080
87-010-402-080
CAP,
CAP,
CAP,
CAP,
CAP,
ELECT
ELECT
ELECT
ELECT
ELECT
10-50V
4.7-50V
4.7-50V
2.2-50V
2.2-50V
B
B
KB
KB
TRANSISTOR
DIODE
87-070-345-080
87-017-072-080
87-027-607-080
87-A40-466-080
87-020-465-080
DIODE,IN4148
ZENER,HZS3B1
ZENER,HZ7B3L
ZENER,MTZJ2.7A
DIODE,1SS133 (110MA)
87-017-162-080
87-017-148-080
87-017-139-010
87-070-136-080
87-A40-465-010
ZENER,HZS7C3L
ZENER,HZS6A1L
ZENER,HZS15-2
ZENER,MTZJ5.1B
DIODE,FR202
C1
C2
C3
C5
C6
87-010-314-080
87-010-316-080
87-010-314-080
87-A11-067-080
87-010-312-080
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
C7
C8
C10
C11
C12
87-014-409-080
87-012-349-080
87-010-197-080
87-010-197-080
87-010-197-080
CAP,PP 470P-100J
C-CAP,S 1000P-50 CH
CAP, CHIP 0.01 DM
CAP, CHIP 0.01 DM
CAP, CHIP 0.01 DM
C13
C14
C15
C16
C17
87-010-150-080
87-012-157-080
87-012-349-080
87-010-380-080
87-010-198-080
C-CAP,S 6P-50 CH
C-CAP 330P-50CH
C-CAP,S 1000P-50 CH
CAP, ELECT 47-16V
CAP, CHIP 0.022
C18
C19
C20
C21
87-015-819-080
87-010-112-080
87-010-404-080
87-010-197-080
CAPACITOR,0.01
CAP, ELECT 100-16V
CAP, ELECT 4.7-50V
CAP, CHIP 0.01 DM
J CH GRM
CH
DM
DM
DM
MAIN C.B
22P-50V
33P-50 CH
22P-50V
1-10 K B
15P CH
4
REF. NO
PART NO.
C263
C264
C265
C266
C267
KANRI
NO.
87-010-178-080
CHIP
87-010-178-080
CHIP
87-010-383-080
CAP,
87-010-383-080
CAP,
87-010-380-080
CAP,
C268
C271
C272
C275
C276
87-010-380-080
87-010-236-080
87-010-236-080
87-010-628-080
87-010-628-080
C277
C278
C279
C299
C301
DESCRIPTION
REF. NO
C853
CF2
CF3
CF4
CN201
KANRI
DESCRIPTION
NO.
87-010-190-080
S CHIP F 0.01
82-785-747-080
CF,MS2 GHY,R
82-785-747-080
CF,MS2 GHY,R
87-A91-094-010
FLTR,CDA10.7 MG
87-099-016-010
CONN,14P 6216V
CAP, ELECT 47-16V
CAP, ELECT 1000-10V
CAP, ELECT 1000-10V
CAP,E 3.3-16 M 5L BP SRE
CAP,E 3.3-16 M 5L BP SRE
CN203
CN204
CN205
CN301
CN801
87-049-469-010
87-049-469-010
87-A60-109-010
S1-2S3-002-500
87-049-469-010
CONN,4P
CONN,4P
CONN,2P
CONN,3P
CONN,4P
87-010-260-080
87-010-263-080
87-010-112-080
87-010-190-080
87-010-453-010
CAP, ELECT 47-25V
CAP, ELECT 100-10V
CAP, ELECT 100-16V
S CHIP F 0.01
CAP, ELECT 4700-25V
CN802
D3
D4
D5
L2
87-049-469-010
87-A40-616-070
87-A40-615-070
87-A40-615-070
87-A50-347-010
CONN,4P V
VARI-CAP,SVC384(S/T)
VARI-CAP,KV1311NT
VARI-CAP,KV1311NT
COIL,FM BPF EX
C306
C307
C308
C309
C310
87-010-404-080
87-010-401-080
87-010-221-080
87-010-263-080
87-010-248-080
CAP,
CAP,
CAP,
CAP,
CAP,
L3
L4
L5
L6
L7
87-A91-096-010
87-A50-420-010
87-A50-424-010
87-A50-427-010
87-A91-308-010
BAR-ANT,MW/LW FOR 3B(SYN)
COIL,MW OSC(SYN)
COIL,FM RF EX(SYN)
COIL,FM OSC EX(SYN)
FLTR,PCFAZH- 450T (TOK)
C311
C312
C314
C315
C321
87-010-384-080
87-010-385-080
87-010-248-080
87-010-197-080
87-010-190-080
CAP, ELECT 100-25V
CAP, ELECT 220-25V
CAP, ELECT 220-10V
CAP, CHIP 0.01 DM
S CHIP F 0.01
L8
L9
L51
L801
R840
87-005-849-080
87-005-849-080
87-A50-421-010
87-007-342-010
87-029-124-010
COIL,10UH(CECS)
COIL,10UH(CECS)
COIL,LW OSC(SYN)
COIL,OSC 85K BIAS
RES,FUSE 2.2-1/4
C322
C325
C341
C342
C343
87-010-263-080
87-010-405-080
87-010-197-080
87-010-221-080
87-010-401-080
CAP,
CAP,
CAP,
CAP,
CAP,
TC1
TC51
X1
87-011-220-080
87-011-233-080
87-A70-061-010
TRIMMER CAP 20P VTC
TRIMER,50P VCT54
VIB,XTAL 4.500MHZ CSA-309
C801
C802
C803
C804
C805
87-010-402-080
87-010-402-080
87-010-181-080
87-010-181-080
87-012-158-080
CAP, ELECT 2.2-50V
CAP, ELECT 2.2-50V
C-CAP,S 1800P-50 KB
C-CAP,S 1800P-50 KB
C-CAP,S 390P-50 CH
C601
C602
C603
C604
C605
87-010-313-080
87-010-315-080
87-010-319-080
87-010-312-080
87-010-317-080
CAP, CHIP 18P
C-CAP,S 27P-50 CH
C-CAP,S 56P-50 J CH
C-CAP,S 15P-50V CH
C-CAP,S 39P-50 CH
C806
C809
C810
C811
C812
87-012-158-080
87-010-379-010
87-010-379-010
87-010-404-010
87-010-404-010
C-CAP,S 390P-50 CH
CAP,E 22-10 SM
CAP,E 22-10 SM
CONDENSER 4.7-50
CONDENSER 4.7-50
C607
C608
C610
C611
C612
87-A11-067-080
87-A11-067-080
87-010-263-080
87-010-196-080
87-010-248-080
C-CAP,S 1-10 K B
C-CAP,S 1-10 K B
CAP, ELECT 100-10
CHIP CAPACITOR,0.1-25
CAP, ELECT 220-10V
C815
C816
C819
C820
C821
87-010-374-010
87-010-384-080
87-010-401-010
87-010-401-010
87-010-183-080
CAP, ELECT 47-10V
CAP, ELECT 100-25V
CAP, ELECT 1-50V
CAP, ELECT 1-50V
C-CAP,S 2700P-50 KB
C613
C614
C615
C616
C620
87-010-402-080
87-010-196-080
87-010-400-080
87-010-401-080
87-A11-067-080
CAP, ELECT 2.2-50V
CHIP CAPACITOR,0.1-25
CAP, ELECT 0.47-50V
CAP, ELECT 1-50V
C-CAP,S 1-10 K B
C822
C823
C824
C825
C826
87-010-183-080
87-010-213-080
87-010-213-080
87-010-405-080
87-010-405-080
C-CAP,S 2700P-50 KB
C-CAP,S 0.015-50 B
C-CAP,S 0.015-50 B
CAP, ELECT 10-50V
CAP, ELECT 10-50V
C627
C628
C691
CN601
CN602
87-010-401-080
87-010-401-080
87-010-405-080
87-099-031-010
87-099-200-010
CAP,E 1-50
CAP,E 1-50
CAP, ELECT 10-50V
CONN,14P 6216 H
CONN,7P 6216H
C827
C828
C830
C831
C832
87-010-404-010
87-010-404-010
87-010-260-080
87-010-198-080
87-010-198-080
CONDENSER 4.7-50
CONDENSER 4.7-50
CAP, ELECT 47-25V
CAP, CHIP 0.022
CAP, CHIP 0.022
CN603
CN604
CN605
FC601
FC602
87-099-199-010
87-099-200-010
87-099-200-010
8Z-CH4-619-010
8Z-CH4-621-010
CONN,6P 6216 H
CONN,7P 6216H
CONN,7P 6216H
FF-CABLE, 14P AF-FR
FF-CABLE, 7P CD-FR
C833
C834
C835
C837
C838
87-010-179-080
87-010-248-080
87-012-358-010
87-010-374-010
87-010-405-080
CAP,CHIP S B1200P
CAP, ELECT 220-10V
C-CAP,S 0.47-16V
CAP, ELECT 47-10V
CAP, ELECT 10-50V
FC603
FC604
FC605
L601
LCD601
8Z-CH4-622-010
8Z-CH4-620-010
8Z-CH4-620-010
87-003-102-010
8Z-CH4-635-010
FF-CABLE, 6P TU-FR
FF-CABLE, 7P FR-LED
FF-CABLE, 7P FR-LED
COIL,10UH TROIDAL
LCD,HLC7365 ZCH-4
C841
C842
C843
C844
C845
87-010-182-080
87-010-182-080
87-010-190-080
87-018-128-080
87-018-128-080
C-CAP,S 2200P-50
C-CAP,S 2200P-50
S CHIP F 0.01
CAP,TC U 560P-50
CAP,TC U 560P-50
S601
S604
S605
S606
S607
87-A90-696-080
87-A90-696-080
87-A90-696-080
87-A90-696-080
87-A90-696-080
SW,TACT
SW,TACT
SW,TACT
SW,TACT
SW,TACT
C846
C849
C850
C851
C852
87-010-194-080
87-010-177-080
87-010-177-080
87-010-186-080
87-010-178-080
CAP, CHIP 0.047
CHIP CAPACITOR 820P
CHIP CAPACITOR 820P
CAP,CHIP 4700P
CHIP CAP 1000P
S614
S615
X601
X602
87-A90-696-080
87-A90-696-080
87-030-273-010
87-A70-070-080
SW,TACT TS2103-03-430
SW,TACT TS2103-03-430
VIB,XTAL 32.768K5PPM
VIB,CER 5.76MHZ CRHF
CAP 1000P
CAP 1000P
ELECT 33-25V
ELECT 33-25V
ELECT 47-16V
ELECT
ELECT
ELECT
ELECT
ELECT
4.7-50V
1-50V
470-10V
100-10V
220-10V
ELECT 100-10V
ELECT 10-50V
CHIP 0.01 DM
ELECT 470-10V
ELECT 1-50V
PART NO.
V
V
V S2M-2W
V
FRONT C.B
KB
KB
KB
KB
5
TS2103-03-430
TS2103-03-430
TS2103-03-430
TS2103-03-430
TS2103-03-430
REF. NO
PART NO.
KANRI
NO.
DESCRIPTION
REF. NO
CD MAIN C.B
C401
C402
C403
C404
C405
87-010-403-080
87-010-197-080
87-010-263-080
87-010-248-080
87-010-197-080
CAP,
CAP,
CAP,
CAP,
CAP,
ELECT 3.3-50V
CHIP 0.01 DM
ELECT 100-10V
ELECT 220-10V
CHIP 0.01 DM
C406
C407
C409
C410
C412
87-010-374-080
87-010-178-080
87-010-248-080
87-010-263-080
87-010-401-080
CAP,
CHIP
CAP,
CAP,
CAP,
ELECT 47-10V
CAP 1000P
ELECT 220-10V
ELECT 100-10V
ELECT 1-50V
C413
C414
C416
C417
C425
87-A11-138-080
87-010-405-080
87-010-545-080
87-012-157-080
87-010-176-080
CAP, CHIP 0.033-50
CAP, ELECT 10-50V
CAP, ELECT 0.22-50V
C-CAP,S 330P-50 CH
C-CAP,S 680P-50 SL
C429
C430
C431
C432
C433
87-010-186-080
87-012-156-080
87-010-545-080
87-010-374-080
87-010-401-080
CAP,CHIP 4700P
C-CAP,S 220P-50 CH
CAP, ELECT 0.22-50V
CAP, ELECT 47-10V
CAP, ELECT 1-50V
C434
C435
C436
C437
C438
87-010-184-080
87-010-197-080
87-010-374-080
87-010-404-080
87-010-196-080
CHIP
CAP,
CAP,
CAP,
CHIP
C440
C442
C445
C446
C447
87-010-145-080
87-010-312-080
87-010-196-080
87-010-196-080
87-010-196-080
C-CAP,S 1P-50 CH
C-CAP,S 15P-50 CH
CHIP CAPACITOR,0.1-25
CHIP CAPACITOR,0.1-25
CHIP CAPACITOR,0.1-25
C448
C450
C451
C455
C457
87-010-315-080
87-012-140-080
87-012-156-080
87-010-263-080
87-010-312-080
C-CAP,S 27P-50 CH
CAP 470P
C-CAP,S 220P-50 CH
CAP, ELECT 100-10V
C-CAP,S 15P-50 CH
C458
C459
C460
C461
C462
87-010-312-080
87-010-263-080
87-010-197-080
87-010-196-080
87-010-248-080
C-CAP,S 15P-50 CH
CAP, ELECT 100-10V
CAP, CHIP 0.01 DM
CHIP CAPACITOR,0.1-25
CAP,E 220-10 SME
C465
C466
C467
C469
C470
87-010-404-080
87-010-196-080
87-010-263-080
87-012-154-080
87-010-544-080
CAP, ELECT 4.7-50V
CHIP CAPACITOR,0.1-25
CAP, ELECT 100-10V
C-CAP,S 150P-50 CH
CAP, ELECT 0.1-50V
C475
C476
C477
C478
C479
87-010-197-080
87-010-236-080
87-010-197-080
87-010-263-080
87-010-197-080
CAP, CHIP 0.01 DM
CAP,E 1000-10 SME
CAP, CHIP 0.01 DM
CAP, ELECT 100-10V
CAP, CHIP 0.01 DM
C480
C481
C482
C483
C484
87-010-221-080
87-010-405-080
87-010-405-080
87-012-156-080
87-012-156-080
CAP, ELECT 470-10V
CAP, ELECT 10-50V
CAP, ELECT 10-50V
C-CAP,S 220P-50 CH
C-CAP,S 220P-50 CH
C489
C490
C491
C492
C493
87-010-196-080
87-010-196-080
87-010-197-080
87-010-221-080
87-010-197-080
CHIP
CHIP
CAP,
CAP,
CAP,
C500
C501
C502
C503
C504
87-010-197-080
87-010-196-080
87-010-322-080
87-010-322-080
87-010-322-080
CAP, CHIP 0.01 DM
CHIP CAPACITOR,0.1-25
C-CAP,S 100P-50 CH
C-CAP,S 100P-50 CH
C-CAP,S 100P-50 CH
C505
C506
C510
87-010-322-080
87-010-322-080
87-010-196-080
C-CAP,S 100P-50 CH
C-CAP,S 100P-50 CH
CHIP CAPACITOR,0.1-25
PART NO.
CN401
CN402
CN403
FC401
L401
KANRI
DESCRIPTION
NO.
87-A60-424-010
CONN,16P V TOC-B
8Z-CH4-614-010
CONN ASSY,6P CD-ME
87-099-195-010
CONN,7P 6216 V
8Z-CH4-618-010
FF-CABLE, 16P CD-RF
87-003-102-080
COIL, 10UH
L404
SFR430
X401
87-008-372-010
87-024-176-080
81-592-641-010
FILTER, EMI BL OIRNI
SFR,100K H NVZ6TLTA
CERAMIC FILTER, 16.93MHZ
CN608
CN609
LED601
LED602
LED603
87-099-200-010
87-099-200-010
88-CD6-630-010
88-CD6-630-010
88-CD6-630-010
CONN,7P 6216H
CONN,7P 6216H
LED,934ID RED
LED,934ID RED
LED,934ID RED
LED604
LED606
LED607
LED608
LED609
88-CD6-630-010
88-CD6-630-010
88-CD6-630-010
88-CD6-630-010
88-CD6-630-010
LED,934ID
LED,934ID
LED,934ID
LED,934ID
LED,934ID
LED610
88-CD6-631-010
LED,934GD GRN
S608
S609
S610
S611
S612
87-A90-696-080
87-A90-696-080
87-A90-696-080
87-A90-696-080
87-A90-696-080
SW,TACT
SW,TACT
SW,TACT
SW,TACT
SW,TACT
S613
87-A90-696-080
SW,TACT TS2103-03-430
87-A60-569-010
JACK,HTJ-035-18
C901
C902
C903
C904
!F901
87-A10-577-080
87-A10-577-080
87-A10-577-080
87-A10-577-080
87-035-347-010
CAP,CER 0.022-50 Z
CAP,CER 0.022-50 Z
CAP,CER 0.022-50 Z
CAP,CER 0.022-50 Z
FUSE,2.5AL 250V T
!FC901
!FC902
87-033-213-010
87-033-213-010
CLAMP,FUSE SMK
CLAMP,FUSE SMK
LED C.B
CAPACITOR 3300P(K)
CHIP 0.01 DM
ELECT 47-10V
ELECT 4.7-50V
CAPACITOR,0.1-25
RED
RED
RED
RED
RED
KEY C.B
TS2103-03-430
TS2103-03-430
TS2103-03-430
TS2103-03-430
TS2103-03-430
HP C.B
J251
PWR C.B
MOTOR-1 C.B
M2
PIN3
SW1
CAPACITOR,0.1-25
CAPACITOR,0.1-25
CHIP 0.01 DM
ELECT 470-10V
CHIP 0.01 DM
6
9X-262-576-910
91-564-722-110
91-572-085-120
MOTOR
CONNECTOR 6P
LEAF SWITCH
YF
YF
YF
YF
LCD DISPLAY
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
8 8
A
Figure
Resistor Code
Value of resistor
Chip resistor
L
W
t
:A
Resistor Code : A
1.0
0.5
0.35
104
1.6
0.8
0.45
108
2
1.25
0.45
118
3.2
1.6
0.55
128
Dimensions (mm)
Wattage
1/16W
Type
1005
Tolerance
5%
Symbol
CJ
1/16W
1/10W
1608
2125
5%
5%
CJ
CJ
1/8W
3216
5%
CJ
Form
L
t
W
TRANSISTOR ILLUSTRATION
ECB
2SA1015
2SA1296
2SA1318
2SC1815
2SC1923
2SC2001
2SC2878
ECB
2SA933S
2SC1740S
DTA114YS
DTC114TK
DTC114TS
DTC114YS
DTC124XS
SGD
GSD
2SJ103
2SK439
7
BCE
2SB1370
8
WIRING-1
1
2
3
4
5
6
7
8
9
10
11
12
A
B
C
D
E
F
G
H
I
J
9
10
13
14
11
12
1/4W
1/4W
SCHEMATIC DIAGRAM-1 (MAIN-1/2 SECTION)
SCHEMATIC DIAGRAM-2 (MAIN 2/2 SECTION)
13
14
SCHEMATIC DIAGRAM-3 (CD MAIN SECTION)
15
16
WIRING-2
1
2
3
4
5
6
7
8
9
10
11
12
A
B
C
D
E
F
G
H
I
J
17
18
13
14
SCHEMATIC DIAGRAM-3 (FRONT, LED, KEY SECTION)
19
20
ADJUSTMENT <TUNER / CD>
PRACTICAL SERVICE FIGURE
C CD MAIN C.B
6
IC401
3
SFR430
IC404
L003 (BAR ANT)
<DECK SECTION>
<FM SECTION>
IHF Sensitivity :
(THD 3%)
Signal to noise ratio :
Tape speed :
Less than 18dB
[at 87.5 / 98 / 108MHz]
Mono : More than 66dB
Stereo : More than 58dB
[at 98MHz ]
Distortion :
Less than 3% [at 98MHz ]
Auto stop level :
24dB ± 10dB
[at 87.5 / 98 / 108MHz]
Stereo separation :
More than 20dB [at 98MHz]
Intermediate frequency : 10.7MHz
TP2 (VREF)
IC402
<TUNER SECTION>
6
TP1 (RF)
A MAIN C.B
Wow & flutter :
Take-up torque :
F.F & REW torque :
Distortion :
S/N ratio :
Max Noise level :
<AM(MW) SECTION>
Sensitivity :
Less than 48dB
S/N (10dB)
[at 600kHz]
Less than 46dB
[at 1000kHz]
Less than 44dB
[at 1400kHz]
Signal to noise ratio :
More than 30dB
[at 600 / 1000 / 1400kHz]
Distortion :
Less than 3%
[at 1000kHz]
Auto stop level :
Less than 70dB
[at 600kHz]
Less than 65dB
[at 1000kHz]
Less than 60dB
[at 1400kHz]
Intermediate frequency : 450kHz
2
L004
3
TC001
L006
5
L005
IC001
IC002
L007
1
4
< TUNER SECTION >
< CD SECTION >
1. AM (MW) IF Adjustment
L007 .............................................................................. 450 kHz
8. Focus Bias Adjustment
Make the focus bias adjustment when replacing and repairing
the optical block.
Oscilloscope
2. AM (MW) VT Adjustment
Settings : • Test point : TP3
• Adjustment location : L004
Method : Set to AM (MW) 1710kHz (HA, LH), 1602kHz (HR)
1611kHz (EZ) and adjust L004 so that the test point
is 6.0 ± 0.05V (HA, LH), 5.6 ± 0.05V (HR, EZ).
(DC range)
TP3 (RF)
3. AM (MW) Tracking Adjustment
L003 .................................. 600kHz (HA, LH), 603kHz (HR, EZ)
TC001 ............................ 1400kHz (HA, LH), 1404kHz (HR, EZ)
TP2 (VREF)
Min Noise level :
Erasing ratio :
Test tape :
<LW SECTION> (EZ)
Sensitivity :
Less than 60dB [at 153kHz]
(S/N 10dB)
Less than 58dB at [198kHz]
Less than 56dB [at 288kHz]
Signal to noise ratio :
More than 30dB
[at 153 / 198 / 288kHz]
Distortion :
Less than 3% [at 198MHz ]
Auto stop level :
Less than 80 / 75 / 70dB
[at 153 / 198 / 288kHz]
Intermediate frequency : 450kHz
+
-
1) Connect an oscilloscope to the test points TP1 (RF) and TP2
(VREF).
2) Turn on the power switch.
3) Insert test disc TCD-782 (YEDS-18) and play back the
second composition.
4) Adjust SFR430 so that RF signal of the test point TP1 (RF)
is MAX and CLEAREST.
4. FM VT Adjustment
Settings : • Test point : TP3
• Adjustment location : L006
Method : Set to FM 108MHz and adjust L006 so that the test
point is 6.0 ± 0.05V.
5. FM Tracking Adjustment
L005 ............................................................................. 108MHz
RF signal waveform
6. LW VT Adjustment<EZ>
Settings : • Test point : TP3
• Adjustment location : L051
Method : Set to LW 288kHz and adjust L051 so that the test
point is 4.5 ± 0.05V.
MAX
EYE PATTERN
7. LW Tracking Adjustment<EZ>
L003 ............................................................................... 153kHz
TC051 ............................................................................ 288kHz
Must be CLEAR and MAX
21
VOLT / DIV: 50mV
TIME / DIV: 0.5µs
22
3000Hz +90 / -60Hz (TN-21ZVC-1816)
3000Hz ± 90Hz (TN-51RV-240)
Less than 0.4% (R.M.S)
30 ~ 60g-cm (FWD) (TN-21ZVC-1816)
20 ~ 60g-cm (FWD) (TN-51RV-240)
55 ~ 140g-cm (TN-21ZVC-1816)
55 ~ 120g-cm (TN-51RV-240)
Less than 3% (PB, 1kHz, DC)
Less than 5% (REC/PB, 1kHz, DC)
More than 35dB (PB, AC, DC)
More than 25dB (REC/PB, AC, DC)
Less than 45mV (PB, DC, AC, VOL
MAX)
Less than 1mV (PB, DC, VOL MIN)
Less than 1.2mV (PB, AC, VOL MIN)
More than 45dB
TTA–100
TTA–210
TTA–782
TTA–602 (NORMAL)
IC BLOCK DIAGRAM
IC, LA6541D
IC, LC72121M
23
IC, M62495FP
IC, MM1434XF
IC, TA2104AN
24
IC DESCRIPTION
IC, LC867132V-5K36
Pin No.
Pin Name
I/O
Description
1
O-RMC/CE
O
CD read/write control output and TU CE.
2
O-DATA
O
Data output to LC72121M, M62495FP.
3
O-CLK
O
Output LC72121M CLK.
4
NC
–
Not Connected.
5
O-CK SFT
O
Clock shift output of the microcomputer.
6
I-HOLD
I
Hold status detection.
7
I-RST
I
Microcomputer reset.
8
XT1 (IN)
I
9
XT2 (OUT)
O
10
VSS1
–
11
CF1 (IN)
I
12
CF2 (OUT)
O
13
VDD1
—
14
I-FM ST
I
FM STEREO status input.
15
I-KEYO
I
KEY AD input.
16
I-CD SW
I
CD DOOR SW status detection input.
17
I-KEY1
I
KEY AD input.
18
I-MOTOR
I
DECK MECHA MOTOR status input.
19
I-REC
I
REC status input.
20
I-FM/AM (NC)
I
FM, AM status input. (Not connected)
21
I-TU DO
I
Data input from LC72121M.
22
O-BASS LED
O
BASS LED ON/OFF control output.
23
O-QS LED
O
Q-Sound LED ON/OFF control output.
24
O-DUBB LED (NC)
O
LED control output used for high-speed dubbing. (Not connected)
25
O-INT
O
INT DIODE MATRIX detection output.
26
I-DRF
I
CD RF level detection input.
27
I-WRQ
I
CD sub-code Q standby input.
28
I-REMO
I
Remote control input.
29
SO-PAO
O
LCD segment output and initial settings output. (SW)
30
S1/PA1
O
LCD segment output and initial settings output. (LW)
31
S2/PA2
O
LCD segment output and initial settings output. (MW 10K)
32
S3/PA3
O
LCD segment output and initial settings output. (FM WIDE)
33
S4/PA4
O
LCD segment output and initial settings output. (OIRT)
34
S5/PA5
O
LCD segment output and initial settings output. (SW2)
35
S6/PA6
O
LCD segment output and initial settings output. (ZCH)
36
S7/PA7
O
37~40
S8~S11
O
41
VDD3
—
Power supply for microcomputer (+5V).
42
VSS3
—
GND.
43~50
S12~S19
O
LCD segment output.
51~54
S20~S23 (NC)
O
LCD segment output. (Not Connected)
55
O-CD LED
O
LED ON/OFF control output for CD functions.
Connected to 32.768KHZ crystal oscillator.
GND.
Connected to 6MHZ Ceramic Filter.
Power supply for microcomputer (+5V).
LCD segment output and initial settings output.
25
Pin No.
Pin Name
I/O
Description
56
O-TU LED
O
LED ON/OFF control output for TU functions.
57
O-TA LED (NC)
O
LED ON/OFF control output for TAPE functions. (Not Connected)
58
O-ROCK LED
O
LED ON/OFF control output for ROCK.
59
O-POP LED
O
LED ON/OFF control output for POP.
60
O-JAZZ LED
O
LED ON/OFF control output for JAZZ.
61
NC
–
62
I-CD TEST (NC)
I
63
I-TU TEST (NC)
I
64~66
COM0~COM2
O
LCD common output.
67
NC
–
Not connected.
68
VSS2
–
GND.
69
VDD2
–
Power supply for microcomputer (+5V).
70
O-CD ON
O
CD PWR control output.
71
O-TU ON
O
TU PWR control output.
72
O-P.CONT
O
Power supply control output.
73
O-HI DUBB (NC)
O
Dubbing speed control output. (Not connected)
74
O-MUTE
O
Main mute output.
75
O-FM MONO (NC)
O
FM force control MONO output. (Not connected)
76
O-BEAT CONT
O
BEAT switch over output.
77
O-QSOUND
O
Q-Sound ON/OFF output.
78
O-COIN
O
CD command output.
79
I-SQOUT
I
CD sub-code Q input.
80
O-CQCK
O
CLK for CD commands/sub-codes.
Not connected.
26
IC, LC78622ED
Pin No.
Pin Name
I/O
Description
1
DEFI
I
Defect detection signal (DEF) input terminal.
2
TAI
I
A pull-down resistor is built in. (Connected to 0V)
3
PDO
O
External VCO control phase comparator output.
4
VVSS
–
Connected to internal VCO of PLL. (Connected to 0V)
5
ISET
I
PDO output current adjustment resistor connection.
6
VVDD
–
Voltage terminal for internal VCO of PLL.
7
FR
I
VCO frequency range adjustment.
8
VSS
–
Digital system ground. (Connected to 0V)
9
EFMO
O
EFM signal output pin.
10
EFMIN
I
EFM signal input pin.
11
T2
I
Test pin. (Connected to 0V)
12
CLV+
O
Disc motor control output.
13
CLV–
14
V/P
O
15
HFL
I
Track detection signal input.
16
TES
I
Tracking error signal input.
17
TOFF
O
Tracking off output.
18
TGL
O
Tracking gain switching output.
19
JP+
O
Track jump output.
20
JP–
21
PCK
O
EFM data playback monitor. Outputs 4.3218MHz when the phase is locked. (Not used)
Rough servo/phase control automatic switching monitor output.
Rough servo at "H". Phase control at "L".
Synchronization signal detection output. Outputs a "H" level when the synchronization
22
FSEQ
O
signal detected from EFM signal and internally generated synchronization signal
range.(Not used)
23
VDD
–
Digital system power supply.
24
SL+
25
SL–
O
Serial data command sled signal output terminal from microprocessor.
26
NC
–
Not used.
27
PU IN
I
CD pickup inside limit switch. (Not used)
28
NC
–
Not used.
29
EMPH
O
30
C2F
O
C2 flag output. (Not used)
31
DOUT
O
Digital output (EIAJ format). (Not used)
32
T3
I
Test input. (Connected to 0V)
33
T4
I
Test input. (Connected to 0V)
34
NC
–
Not used.
35
MUTEL
O
Left channel mute output. (Not used)
36
LVDD
–
Left channel power supply.
37
LCHO
O
Left channel output.
De-emphasis monitor pin. A "H" level indicates playback of a de-emphasis disc.
(Not used)
27
Pin No.
Pin Name
I/O
Description
38
LVSS
–
Left channel ground.
39
RVSS
–
Right channel ground.
40
RCHO
O
Right channel output.
41
RVDD
–
Right channel power supply.
42
MUTER
O
Right channel mute output. (Not used)
43
XVDD
–
Crystal oscillator power supply.
44
XOUT
O
45
XIN
I
46
XVSS
–
Crystal oscillator ground.
47
SBSY
O
Subcode block synchronization signal. (Not used)
48
EFLG
O
C1, C2 single and double error correction monitor pin. (Not used)
49
PW
O
Subcode P,Q,R,S,T,U and W output. (Not used)
50
SFSY
O
Subcode frame synchronization signal output. (Not used)
51
SBCK
I
Subcode readout clock input. (Connected to 0V)
52
FSX
O
53
WRQ
O
Subcode Q output standby output.
54
RWC
I
Read/Write control input.
55
SQOUT
O
Subcode Q output.
56
COIN
I
Command input from the control microprocessor.
57
CQCK
I
Input for command input acquisition clock and SQOUT pin subcode readout clock.
58
RES
I
Chip reset input.
59
T11
O
Test output. Leave open. (Not used)
60
16M
O
16.9344MHz output. (Not used)
61
4.2M
O
4.2336MHz output.
62
T5
I
Test input. (Connected to 0V)
63
CS
I
Chip select input. (Connected to 0V)
64
T1
I
Test input. (Connected to 0V)
Connections for a 16.9344MHz crystal oscillator element.
Output for the 7.35kHz synchronization signal divided from the crystal oscillator.
(Not used)
28
IC, LA9241ML
Pin No.
Pin Name
I/O
1
FIN2
I
Description
Pin No.
Pin Name
I/O
Description
Connected to pickup photo-diode. Adding with FIN1 pin generates RF signal, and
41
RFSM
O
Output RF.
subtracting from FIN1 generates FE signal.
42
RFS–
O
Establish RF gain and 3T compensation value from EFM signal with RFSM pin.
2
FIN1
I
Connected to pickup photo-diode.
43
SLC
O
SLICE LEVEL CONTROL: Control data slice level by DSP with RF waveform.
3
E
I
Connected to pickup photo-diode. Subtracting from F pin generates TE signal.
44
SLI
I
Control data slice level by DSP.
4
F
I
Connected to pickup photo-diode.
45
DGND
–
Digital GND.
5
TB
I
Input DC components of TE signal.
46
FSC
O
Connected to focus search smoothing capacitor.
6
TE–
O
Connected to TE pin with resistor set TE signal gain.
47
TBC
I
TRACKING BALANCE CONTROL: Establish EF balance variable range.
7
TE
O
Output TE signal.
48
NC
–
Not used.
8
TESI
I
Input TES (TRACK ERROR SENSE) comparator. Band pass and input TE signal.
49
DEF
O
Output disc defect detection.
9
SCI
I
Input shock detection.
50
CLK
I
Input reference clock. Inputs 4.23MHz from DSP.
10
TH
I
Establish tracking gain value.
51
CL
I
Input microcomputer command clock.
11
TA
O
TA amplifier output.
52
DAT
I
Input microcomputer command data.
12
TD–
I
Compose tracking phase compensation value between TD and VR pins.
53
CE
I
Input microcomputer command chip enable.
13
TD
O
Used for tracking phase compensation setting.
54
DRF
O
Detect RF: Output RF level detection.
14
JP
I
Establish amplitude of tracking jump signal (kick pulse).
55
FSS
I
FOCUS SEARCH SELECT: Switches focus search mode (between ± search
and + search against reference voltage). (Not used)
15
TO
O
Output tracking control signal.
16
FD
O
Output focusing control signal.
56
VCC2
–
Servo/digital VCC.
17
FD–
I
Compose focusing phase compensation value between FD and FA pins.
57
REF1
–
Connected to reference voltage bypass condenser.
18
FA
O
Compose focusing phase compensation value between FD– and FA– pins.
58
VR
O
Output reference voltage.
19
FA–
I
Compose focusing phase compensation value between FA and FE pins.
59
LF2
–
Establish value in detecting disc defect.
20
FE
O
Output FE signal.
60
PHI
–
Connected to capacitor used to hold peak of RF signal.
21
FE–
I
Connected to FE pin with resistor set FE signal gain.
61
BHI
–
Connected to capacitor used to hold bottom of RF signal.
22
AGND
–
Analog GND.
62
LDD
O
APC-circuit output pin.
23
SP
O
Output single-end for CV+ and CV– pins input signal.
63
LDS
I
APC-circuit input pin.
24
SPI
I
Spindle amplifier input.
64
VCC1
–
RF VCC.
25
SPG
I
Connect resistor for gain setting at spindle 12cm mode. (Not used)
26
SP–
I
Connect spindle phase compensation value with SPD pin.
27
SPD
O
Output spindle control signal.
28
SLEQ
I
Connect sled phase compensation value.
29
SLD
O
Output sled control signal.
30
SL–
I
Input sled sending signal from DSP.
31
SL+
32
JP–
I
Input tracking jump signal from DSP.
33
JP+
34
TGL
I
Input tracking gain control signal from DSP. TGL = "H" : Gain low.
35
TOFF
I
Input tracking off control signal from DSP. TOFF = "H" : Off.
36
TES
O
Output TES signal to DSP.
37
HFL
O
HIGH FREQUENCY LEVEL: Detects whether main-beam is on pit or mirror position.
38
SLOF
I
Input sled servo off control.
39
CV–
I
Input CLV error signal from DSP.
40
CV+
29
30
MECHANICAL EXPLODED VIEW 1/1
LCD
TACT C.B
40
20
47
14
62
21
66
DISP C.B
13
37
39
36
35
22
34
67
61
19
B
7
15
B
33
38
B
K
49
48
8
P.C.B
32
B
11
26
A
F
68
18
10
9
K
12
42
17
F
10
16
C
44
60
52
D
59
A
LED C.B
K
5
64
54
A
I
41
K
25
F
F
F
H
53
I
KSM213CDM
I
30
L
F
58
C
BATT C.B
P.C.B
24
B
TN-21ZVC-1816
65
10
B
57
F
11
J
55
K
12
63
29
K
K
K
4
K
10
K
MAIN C.B
3
2
51
B
E
1
F
46
27
43
45
56
23
K
P.C.B
A
31
28
K
48
50
10
6
9
31
K
32
6
MECHANICAL PARTS LIST 1/1
REF. NO
1
2
3
4
5
PART NO.
KANRI
DESCRIPTION
NO.
87-B00-020-010
BADGE,AIWA 30 GOLD
8Z-CH4-007-010
WINDOW,CASS
8Z-CH4-006-010
BOX,CASS
8Z-CH4-205-010
SPR-T,CASS
8Z-CH4-061-010
CABI,FR A
REF. NO
45
46
47
48
49
PART NO.
KANRI
DESCRIPTION
NO.
87-CD6-041-010
PLATE,AC
8Z-CH4-640-010
ANT,ROD
8Z-CH4-009-010
HANDL,ARM
8Z-CH4-645-010
SPKR,MAYLOR 8OHM SILVER
8Z-CH4-010-010
HANDL,GRIP
6
7
8
9
10
86-CT4-218-010
8Z-CH4-019-010
8Z-CH4-020-010
88-CD5-603-010
8Z-CH4-204-010
CUSHION,FOOT/PORON
CABI,TOP 2L
CABI,TOP 2R
SPKR,10 7OHM
HLDR,SPEAKER
50
51
52
53
! 54
8Z-CH4-008-010
87-CD6-223-010
87-CD6-214-010
8Z-CH4-002-010
88-CH6-627-010
LID,BATT
SPR-C,BATT LINK L
SPR-C,BATT LINK
CABI,REAR
PT,E
11
12
13
14
15
84-CD5-215-010
84-CD5-216-010
8Z-CH4-216-010
8Z-CH4-201-010
8Z-CH4-016-010
GEAR
BRACKET
HLDR,FUNC-PWB
HLDR,LCD
WINDOW,LED
55
! 56
57
58
59
8Z-CH4-209-010
87-A60-178-010
87-CD6-222-010
87-CD6-213-010
8Z-CH4-614-010
HLDR,PT
JACK,AC E W/SW
SPR-C,BATT (-) L
SPR-C,BATT (-)
CONN ASSY,6P CD-ME
16
17
18
19
20
8Z-CH4-210-010
8Z-CH4-027-010
8Z-CH4-026-010
8Z-CH4-025-010
8Z-CH4-064-010
HLDR,LED
BTN,EQ
BTN,FUNC
BTN,REPEAT
WINDOW,LCD EZ
60
61
62
63
64
8Z-CH4-618-010
8Z-CH4-621-010
8Z-CH4-619-010
88-CH6-207-010
8Z-CH4-011-010
FF-CABLE,
FF-CABLE,
FF-CABLE,
HLDR,ANT
GRILLE,FR
21
22
23
24
25
8Z-CH4-023-010
8Z-CH4-013-010
8Z-CH4-028-010
8Z-CH4-214-010
87-A91-151-010
BTN,VOL
PANEL,LCD21
KEY,CASS 21
HLDR,REC-SW 21
SW,LEAF 1P2T/TC48-021
65
66
67
68
A
8Z-CH4-012-010
8Z-CH4-021-010
8Z-CH4-022-010
8Z-CH4-626-010
87-B10-242-010
GRILLE,FR R
GRILLE,TOP L
GRILLE,TOP R
FF-CABLE, 7P FR-LED1
UT2+3-30 W/O CR
26
27
28
29
30
8Z-CH4-024-010
88-CH6-019-010
87-036-389-010
8Z-CH4-208-010
8Z-CH4-030-010
BTN,CD
PANEL,CD
SW,PUSH LOCK
HLDR,PWB
COVER, PH
B
C
D
E
F
87-B10-239-010
87-644-096-410
87-254-097-410
87-751-075-410
87-342-074-010
QT2+3-8 W/O CR
UT1+3-10 CR
U+3-12 CR
VT2+2.6-10
UT2+2.6-8
31
32
33
34
8Z-CH4-003-010
8Z-CH4-207-010
8Z-CH4-212-010
8Z-CH4-211-010
CHAS,CD
HLDR,OIL-DMPR
RING,CHUCK
BASE,CHUCK
G
H
I
J
K
87-751-094-410
87-261-037-410
87-661-100-410
87-067-566-010
87-741-095-410
VT2+3-6 W10SL0T
V+2-10 GLD
VFT1+3-16
TAPPING SCREW, VFTT+3-6
UT2+3-8 GLD
35
36
37
38
39
87-036-368-010
84-CD5-217-010
85-CD7-217-010
8Z-CH4-206-010
8Z-CH4-004-010
MAGNET
PLATE,MAGNET
HLDR,CHUCK A
SPR-T,CD
BOX,CD
40
41
42
43
44
8Z-CH4-005-010
8Z-CH4-213-010
8Z-CH4-622-010
8Z-CH4-627-010
87-A90-086-010
WINDOW,CD
SPR-P,REC-SW 21
FF-CABLE, 6P TU-FR
FF-CABLE, 7P FR-LED2
COVER,AC-SOCKET
L 87-571-032-410
16P CD-RF
7P CD-FR
14P AF-FR
L
VIT+2-3
COLOR NAME TABLE
Basic color symbol
Color
Basic color symbol
Color
Basic color symbol
Color
B
Black
C
Cream
D
Orange
G
Green
H
Gray
L
Blue
LT
Transparent Blue
N
Gold
P
Pink
R
Red
S
Silver
ST
Titan Silver
T
Brown
V
Violet
W
White
WT
Transparent White
Y
Yellow
YT
Transparent Yellow
LM
Metallic Blue
LL
Light Blue
GT
Transparent Green
LD
Dark Blue
DT
Transparent Orange
33
TAPE MECHANISM EXPLODED VIEW 1/1
F
LUG PLATE
G
52
1
46
E
2
R
M
4
3
6
5
47
7
8
55
11
a
10
9
J
L
12
53
20
21
36
b
22
14
16
18
23
13
15
31
17
19
49
30
24
32
34
35
33
51
A
26
25
b
27
N
28
A
29
a
54
56
C
N
48
c
37
C
B
B
38
B
40
39
57
D
D
c
K
I
41
42
N
43
N
50
44
45
34
TAPE MECHANISM PARTS LIST 1/1
REF. NO
1
2
3
4
5
PART NO.
KANRI
DESCRIPTION
NO.
S1-921-030-4A0
HEAD BASE
S1-821-030-070
AZIMUTH SPRING
S1-921-030-090
PANEL P SPRING
S1-921-260-050
GEAR PLATE SPRING
S1-921-265-020
GEAR PLATE ASSY
REF. NO
PART NO.
41
42
43
44
45
KANRI
DESCRIPTION
NO.
S1-921-140-160
E ACTUATOR SPRING
S1-921-093-030
FLYWHEEL ASSY
S1-921-090-040
MAIN BBELT
S1-921-120-010
MOTOR PULLEY
S6-002-030-220
MOTOR EG530AD-2B
6
7
8
9
10
S1-921-140-370
S1-921-140-340
S1-921-030-110
S1-921-143-160
S1-921-141-8A0
P ARM COLLER
P ARM
HEAD PANEL
BASE ASSY
M CONTROL SPRING
46
47
48
49
50
S6-209-100-100
S1-921-030-050
S1-921-140-210
S1-821-100-690
S1-921-120-540
E HEAD PH-K380-MS1
MG ARM
REC BUTTON LEVER SPRING
RECORD SAFETY LEVER
MOTOR BRACKET
11
12
13
14
15
S1-921-260-4A0
S1-921-043-100
S1-921-130-010
S1-921-141-3A0
S1-921-140-550
SENSING LEVER
PINCH ROLLER ARM ASSY
EJECT SLIDE LEVER
P CONTROL SPRING
PAUSE LEVER(E)
51
52
53
54
55
S1-821-010-500
S6-202-010-920
S6-401-011-490
S1-921-015-010
S1-921-030-100
PLAY BUTTON LEVER SPRING
R.P HEAD MS15R-AK0N1
LEAF SW MSW-1541T
CHASSIS ASSY
MG ARM SPRING
16
17
18
19
20
S1-921-140-120
S1-921-140-110
S1-921-140-150
S1-821-011-590
S1-921-140-140
PAUSE LEVER SPRING
PAUSE STOPPER
BUTTON LEVER SPRING(B)
E KICK LEVER
BUTTON LEVER SPRING(A)
56
57
A
B
C
S1-921-010-160
S1-821-120-660
S9-P04-200-310
S1-851-140-180
S9-B10-200-510
SIDE BRACKET
MOTOR RUBBER
C TAPPING SCREW 2-3
MOTOR COLLER SCREW
P TAPPING BIND SCREW M2-5
21
22
23
24
25
S1-921-140-200
S1-921-140-090
S1-921-140-080
S1-921-140-190
S1-510-020-020
PR STOPPER
SWITCH ACTUATOR
PUSH BUTTON ACTUATOR
PLAY BUTTON LEVER
REC SPRING PLATE
D
E
F
G
H
S9-C07-204-510
S9-P01-200-610
S9-P01-200-310
S9-F08-200-710
S9-P05-200-810
SCREW,TAPPING(CAMERA)M2-4.5
SCREW,M2-6
SCREW,M2-3
AZIMUTH SCREW M2-7
S TAPPING SCREW M2-8
26
27
28
29
30
S1-921-140-040
S1-921-140-050
S1-921-140-060
S1-921-140-600
S1-821-100-700
REW BUTTON LEVER
FF,BUTTON REVER
STOP BUTTON LEVER
PAUSE BUTTON LEVER
FF GEAR
I
J
K
L
M
S9-W02-300-100
S9-W02-500-100
S9-W01-400-100
S9-W01-130-200
S9-P08-203-010
P WASHER CUT 1.2-3.8-0.3
P WASHER CUT 1.45-3.8-0.5
P WASHER 2-3.5-0.4
P WASHER 2.1-4-0.13
PS TAPPING SCREW M2-3
31
32
33
34
35
S1-921-050-060
S1-921-053-030
S1-821-100-980
S1-921-053-040
S1-821-100-990
SENSOR
TAKE UP REEL ASSY
PACK SPRING
SUPPLY REEL ASSY
BACK TENSION SPRING
N S9-P04-200-410
36
37
38
39
40
S1-921-140-030
S1-921-140-170
S1-921-073-040
S1-921-070-030
S1-921-260-020
REC BUTTON LEVER
P.S.LEVER SPRING
RF CLUTCH ASSY
RF BELT
CAM GEAR
35
C TAPPING SCREW M2-4
CD MECHANISM EXPLODED VIEW
2
COVER
GEAR
3
A
SPINDLE MOTOR
(M1)
1
4
MOTOR C.B
CD MECHANISM PARTS LIST 1/1
REF. NO
1
2
3
4
A
PART NO.
KANRI
DESCRIPTION
NO.
9X-262-620-210
MOTOR CHASSIS ASSY
92-626-907-010
GEAR(A)
87-A90-468-010
PICK UP KSS-213C
92-626-908-010
SHAFT SLED
97-621-255-150
SCREW+P2-3
36
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
931196
Printed in Singapore