Cache Vault Accessory Kit

First Edition (V1) T7843
November 2012
Cache Vault Accessory Kit
Quick Start Guide
Copyright © 2012 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
Contents
Package contents.................................................................................. 2
Installing the Cache Vault Kit on the holder and the PIKE card........ 3
Installing the Cache Vault Power Module on the steel clip and holder......3
Standard installation of Cache Vault power module..................................3
Installing the Cache Vault Flash Module on the PIKE 2208 card..............4
Installing the Cache Vault Kit on specific ASUS server systems...... 5
Installing the kit on RS720-X7/RS8, RS720-E7/RS12, RS720-E7/RS12-E
server systems..........................................................................................5
Installing the kit on TS700-X7/PS4, TS700-E7/RS8 server systems........5
Installing the kit on RS920-E7/RS8, RS926-E7/RS8 server systems.......6
Installing the kit on ESC4000 G2 GPU server system..............................7
15060-09V10000
Package contents
LSI® MegaRAID® Cache Vault Accessory Kit
Cache Vault Flash Module
(CVFM02)
Screws (1): 3 screws for
Cache Vault Flash Module
Cache Vault Power Module
(CVPM02)
24” cable extender
LSI® steel CVPM clip
Screws (2): For LSI® steel
CVPM clip (3 screws, 3 screw
caps*)
ASUS Accessory Kit
Steel bracket (1 x Fullheight, 1 x Half-height)
ASUS steel CVPM clip
holder
Screws (3): 2 screws for the Screws (4): 3 screws** for ASUS
steel bracket
steel CVPM clip holder
* U
se these screws (2) and screw
caps when installing LSI® steel
CVPM clip on ASUS steel CVPM
clip holder. Use the screw caps
depending on the situation.
(Supported servers: RS720-X7/
RS8, RS720-E7/RS12, RS720E7/RS12-E)
42” cable extender
** U
se these screws (4) when
installing LSI® steel CVPM
clip directly on ASUS servers.
(Supported servers: RS920-E7/
RS8, RS926Q-E7/RS8)
If any of the above items is damaged or missing, contact your retailer.
Cache Vault Accessory Kit
Installing the Cache Vault Kit on the holder
and the PIKE card
Install the Cache Vault Flash Module on the PIKE 2208 card, and follow the steps
below to install the Cache Vault Power Module on ASUS steel CVPM holder.
Installing the Cache Vault Power Module on the steel clip and holder
1.
Locate the three screw holes on
ASUS steel CVPM clip holder.
3.Align the three screw holes on
the clip with the three screw holes
on the holder, then secure the clip
with the bundled screws (2).
2.
Find the LSI® steel CVPM clip
for securing the Cache Vault
Power Module.
4.Install the Cache Vault Power
Module to the LSI® steel
CVPM clip.
Standard installation of Cache Vault power module
Some specific ASUS server systms have a specific space for installing Cache Valut Power
module, allowing you the use of all your system’s expansion slots. For generally standard
installation, please follow the steps below.
1.Install the Cache Vault Power Module on the full-height or half-height steel bracket
according to the type of expansion slots on your server system as shown below.
CVPM installed on the full-height steel
bracket, secured with the bundle screws (3).
Cache Vault Accessory Kit
CVPM installed on the half-height steel
bracket, secured with the bundle screws (3).
2.
Install the Cache Vault Power Module on your server system.
The images shown below are for reference only.
Installed on a 2U server system.
Installed on a 5U server system.
Installing the Cache Vault Flash Module on the PIKE 2208 card
1.
Place the PIKE 2208 card
on a flat, stable surface.
Locate the three screw
holes on it.
2.Locate the three screw washers on
the Cache Vault Flash Module.
3.Align the three screw
washers to the three screw
holes on the PIKE 2208
card. Drive in the bundled
screws (1) to secure the
Cache Vault Flash Module.
If the PIKE 2208 card is already installed in a server system, uninstall it from the
system, and install the Cache Vault Flash Module to the PIKE 2208 card as instructed
above. For details, refer to user manual that came with your server system.
Cache Vault Accessory Kit
Installing the Cache Vault Kit on specific
ASUS server systems
After installing the Cache Vault Falsh Module on the PIKE 2208 card, and installing
the Cache Vault Power Module on the steel CVPM clip and holder, install these two
assemblies to the specific ASUS server systems as instructed below.
Installing the kit on RS720-X7/RS8, RS720-E7/RS12, RS720-E7/
RS12-E server systems
1.Locate the two screw holes on the
right side of the server chassis.
2.Align the two screws on the side of
the steel CVPM holder installed with
the Cache Vault Power Module to
the two screw holes on the right side
of the server chassis. Secure the
holder assembly with two screws, and
connect the 42’’ cable extender to the
Cache Vault Power Module.
3. Connect the other end of the 42’’
cable extender to the Cache Vault
Flash Module that is installed on the
PIKE 2208 card.
screw
locations
4.Install the PIKE 2208 card into the
server system. Arrange the cable
extender in the direction of the arrows.
Installing the kit on TS700-X7/PS4, TS700-E7/RS8 server systems
1.Remove the chassis cover and lay
the system on its side on a flat, stable
surface. Use a Phillip driver to remove
the screw on the metal slot cover and set
the screw aside. Remove the metal slot
cover.
Remove the metal slot cover close
to the bottom of the server chassis.
Cache Vault Accessory Kit
2.Align the two screws on the side
of the steel CVPM holder installed
with the Cache Vault Power Module
to the screw holes of the full-height
steel bracket. Secure the holder
assembly with the bundled screws
(3).
3.
Place the holder assembly into the
system and secure it with the screw
removed earlier in step 1.
4.
Install the PIKE 2208 card installed
with the Cache Vault Flash Module
on the system. Connect the cable
from the Cache Vault Power Module
to the Cache Vault Flash Module.
5.
Secure the cable to the bottom
chassis cover using a piece of
acetate cloth tape.
Installing the kit on RS920-E7/RS8, RS926-E7/RS8 server systems
1.
Take out the riser card bracket from
the system and place it on a flat, stable
surface. Locate the three screws.
For more details on how to uninstall the riser card bracket, refer to the user
manual that came with your server system.
Cache Vault Accessory Kit
2.
Align the three screw holes on the
LSI® steel CVPM clip to the three
screw holes on the bracket, and
secure the clip with the bundled
screws (4).
3.
Install the Cache Vault Power
Module to the clip and connect the
42’’ cable extender to it.
4.
Connect the other end of the 42’’
cable extender to the Cache Vault
Flash Module which is installed on
the PIKE 2208 card.
5.
Install the PIKE 2208 card to the
expansion slot, and then install the
bracket to the system as shown.
Wrap the excessive part of the
cable and place it into the gap
beside the PIKE 2208 card.
PIKE 2208 card
For more details on how to uninstall the riser card bracket, refer to the user
manual that came with your server system.
Installing the kit on ESC4000 G2 GPU server system
1.
Align the two screws on the side of
the steel CVPM holder installed with
the Cache Vault Power Module to the
screw holes of the full-height steel
bracket. Secure the holder assembly
with the bundled screws (3).
Cache Vault Accessory Kit
2.
Take out the riser card bracket from
the right side of the server system.
Align the screw holes on the holder
assembly to the screws holes on
the bracket, then secure the holder
assembly with a screw.
3.
Put the cable through the hole on
the bracket.
For more details on how to
uninstall the riser card bracket,
refer to the user manual that
came with your server system.
4.
Place the bracket into the server
system and secure it with screws.
For more details on how to
uninstall the riser card bracket,
refer to the user manual that
came with your server system.
5.
Connect the cable from the Cache
Vault Power Module to the Cache
Vault Flash Module that is installed
on the PIKE 2208 card.
6.
Install the PIKE 2208 card to the
riser card bracket.
7.
Install the bracket to the system
according to the instructions in the
server system's user manual.
Cache Vault Accessory Kit
Cache Vault Accessory Kit
快速安裝手冊
版權說明
©ASUSTeK Computer Inc. All rights reserved. 華碩電腦股份有限公司保留所有權利
本使用手冊包括但不限於其所包含的所有資訊皆受到著作權法之保護,未經華碩
電腦股份有限公司(以下簡稱「華碩」)許可,不得任意地仿製、拷貝、謄抄、轉
譯或為其他利用。
免責聲明
本使用手冊是以「現況」及「以目前明示的條件下」的狀態提供給您。在法律允
許的範圍內,華碩就本使用手冊,不提供任何明示或默示的擔保及保證,包括但不
限於商業適銷性、特定目的之適用性、未侵害任何他人權利及任何得使用本使用手
冊或無法使用本使用手冊的保證,且華碩對因使用本使用手冊而獲取的結果或透過
本使用手冊所獲得任何資訊之準確性或可靠性不提供擔保。
台端應自行承擔使用本使用手冊的所有風險。 台端明確了解並同意,華碩、華
碩之授權人及其各該主管、董事、員工、代理人或關係企業皆無須為您因本使用手
冊、或因使用本使用手冊、或因不可歸責於華碩的原因而無法使用本使用手冊或其
任何部分而可能產生的衍生、附隨、直接、間接、特別、懲罰或任何其他損失(包
括但不限於利益損失、業務中斷、資料遺失或其他金錢損失)負責,不論華碩是否
被告知發生上開損失之可能性。
由於部分國家或地區可能不允許責任的全部免除或對前述損失的責任限制,所以
前述限制或排除條款可能對您不適用。
台端知悉華碩有權隨時修改本使用手冊。本產品規格或驅動程式一經改變,本使
用手冊將會隨之更新。本使用手冊更新的詳細說明請您造訪華碩的客戶服務網 http://
support.asus.com,或是直接與華碩資訊產品技術支援專線 0800-093-456 聯絡。
於本使用手冊中提及之第三人產品名稱或內容,其所有權及智慧財產權皆為各別
產品或內容所有人所有且受現行智慧財產權相關法令及國際條約之保護。
當下列兩種情況發生時,本產品將不再受到華碩之保固及服務:
(1)本產品曾經過非華碩授權之維修、規格更改、零件替換或其他未經過華碩
授權的行為。
(2)本產品序號模糊不清或喪失。
目錄
包裝盒內容物........................................................................................... 2
安裝 Cache Vault 套件至支架與 PIKE 控制卡............................................ 3
安裝 Cache Vault 電源模組至 CVPM 鐵件夾與支架...............................3
Cache Vault 電源模組一般標準安裝......................................................3
安裝 Cache Vault 快閃記憶體模組至 PIKE 2208 控制卡.......................4
Cache Vault 電源模組安裝至特定華碩伺服器............................................ 5
安裝至 RS720-X7/RS8、RS720-E7/RS12、RS720-E7/RS12-E 伺服器...5
安裝至 TS700-X7/PS4、TS700-E7/RS8 伺服器....................................5
安裝至 RS920-E7/RS8、RS926-E7/RS8 伺服器....................................6
安裝至 ESC4000 G2 GPU 伺服器..........................................................7
包裝盒內容物
®
®
LSI MegaRAID Cache Vault Accessory Kit 組件
Cache Vault 快閃記憶體模組 螺絲(1):Cache Vault 快閃記
Cache Vault 電源模組
(Cache Vault Flash Module) 憶體模組專用螺絲(3 顆) (Cache Vault Power Module)
(CVFM02)
(CVPM02)
24 吋纜線延長線
(24”Cable extender)
®
®
LSI CVPM 鐵件夾
(Steel CVPM clip/holder)
螺絲(2):LSI CVPM 鐵件夾
專用螺絲與螺帽 *(含 3 顆螺
絲、3 個螺帽)
鐵件擋板(半高與全高各一
個)
螺絲(3):鐵件擋板螺絲 2 顆
華碩 CVPM 鐵件夾專用支架
42 吋纜線延長線
(42”Cable extender)
螺絲(4):華碩 CVPM 鐵件夾
專用支架組裝用螺絲 3 顆 **
* 螺
絲(2)(含螺帽)為提供
安裝於華碩 CVPM 鐵件夾
專用支架時使用(螺帽為
視現況需求安裝)(支援
RS720-X7/RS8、RS720-E7/
RS12、RS720-E7/RS12-E
伺服器使用)。
** 螺
絲(4) 為提供 LSI® CVPM
鐵件夾直接安裝於華碩伺服
器時使用(支援 RS920-E7/
RS8、RS926Q-E7/RS8 伺服
器使用)。
華碩專用組件
若以上列出的任何一項配件有損壞或是短缺的情形,請儘速與您的經銷
商連絡。
10
Cache Vault Accessory Kit 快速安裝手冊
安裝 Cache Vault 套件至支架與 PIKE 控制卡
首先,我們先將 Cache Vault 快閃記憶體模組安裝至 PIKE 2208 控制卡,以及將
Cache Vault 電源模組安裝至專用支架,請依照以下的說明進行。
安裝 Cache Vault 電源模組至 CVPM 鐵件夾與支架
1. 取出華碩 CVPM 鐵件夾專用支
架,找到上面三個螺絲孔位。
®
3. 翻轉 LSI CVPM 鐵件夾與專用支
架至背面,將鐵件夾上的安裝孔
位對準專用支架,並鎖上三顆包
裝盒內附的螺絲(2)。
2. 取出 LSI® CVPM 鐵件夾以供固定
Cache Vault 電源模組。
4. 然後,再將 Cache Vault 電源模組
®
裝入 LSI CVPM 鐵件夾裡,完成
初步安裝。
Cache Vault 電源模組一般標準安裝
在特定華碩伺服器系統內已有設計安裝 Cache Vault 電源模組的專用位置,可以免
除佔用一個介面卡擴充插槽。一般標準安裝,請參考以下方式進行。
1. 依照您的伺服器系統內提供的介面卡擴充槽形式,選擇裝上全高或半高鐵件擋
板,如下圖所示。
裝上全高鐵件擋板(使用螺絲(3) 鎖上)。
Cache Vault Accessory Kit 快速安裝手冊
裝上半高鐵件擋板(使用螺絲(3) 鎖上)。
11
2. 接著就可以將 Cache Vault 電源模組裝入各型伺服器系統中。
因各型伺服器不同,以下圖示為僅供安裝介面卡時的示意參考使用。
裝入 2U 伺服器。
裝入 5U/ 直立式伺服器。
安裝 Cache Vault 快閃記憶體模組至 PIKE 2208 控制卡
1. 取出 PIKE 2208 控制卡,放置
在平坦的桌面上,找到上面三
個螺絲安裝孔位。
2. 然後取出 Cache Vault 快閃記憶體模
組,找到上面三根螺絲安裝腳座。
3. 將 Cache Vault 快閃記憶體模組
翻轉至背面,然後將三根安裝
腳座對準 PIKE 2208 控制卡上
的安裝孔位,並從控制卡背面
鎖上三顆螺絲(1),完成固定。
若您的 PIKE 2208 控制卡已安裝在伺服系系統內,請先從系統內取出
(請參考伺服器系統使用手冊的說明)後再行安裝 Cache Vault 快閃記
憶體模組。
12
Cache Vault Accessory Kit 快速安裝手冊
Cache Vault 電源模組安裝至特定華碩伺服器
當安裝好 Cache Vault 快閃記憶體模組的 PIKE 2208 控制卡,以及裝上支架的
Cache Vault 電源模組後,接著就可以依照以下的說明,將這兩個組件裝至下列特定
的華碩伺服器系統裡。
安裝至 RS720-X7/RS8、RS720-E7/RS12、RS720-E7/
RS12-E 伺服器
1. 找到位於伺服器系統機殼右側的螺絲
安裝孔位。
2. 取出已裝上 Cache Vault 電源模組鐵件
夾的支架,如右圖所示,將此支架裝
入機殼側邊內側,並鎖上螺絲,然後
連接 42 吋纜線延長線。
螺絲的位置
3. 然後,再將延長線的另一端則連接至
Cache Vault 快閃記憶體模組上面的插
座。
4. 接著將 PIKE 2208 控制卡裝回系統中,並
依照箭頭所示的方向,整理好延長線的線
路。
安裝至 TS700-X7/PS4、TS700-E7/RS8 伺服器
1. 打開機殼蓋板並將系統橫放平躺於桌面
上,使用十字螺絲起子,鬆開最後一支擋
板上的螺絲,並取出擋板,請將螺絲先放
置於一旁。
此為靠近機殼底部的擋板。
Cache Vault Accessory Kit 快速安裝手冊
13
2. 取出已裝上 Cache Vault 電源模組鐵件
夾的支架,並於支架側邊鎖上全高擋
板(使用螺絲(3) 安裝)。
3. 裝上此支架至機殼內,並鎖上先前放
置一旁的螺絲,完成固定。
4. 將已裝好 Cache Vault 快閃記憶體模組
的 PIKE 2208卡裝入系統,並將 Cache
Vault 電源模組上的纜線連接至 Cache
Vault 快閃記憶體模組上的插座,如右
圖所圈處。
5. 最後,將纜線以醋酸膠帶連貼於底座
上,完成安裝。
安裝至 RS920-E7/RS8、RS926-E7/RS8 伺服器
1. 從系統中取出轉接卡,並放置於平坦
的桌面上,找到如右圖所示的三個螺
絲孔位。
若想要了解更多關於如何拆裝轉接卡的步驟,請參考伺服器系統使用手
冊上的說明。
14
Cache Vault Accessory Kit 快速安裝手冊
®
2. 取出 LSI CVPM 鐵件夾(不需裝上
專用支架),使用產品包裝內附的螺
絲,如右圖所示將此鐵件夾使用三顆
鐵件夾專用螺絲(4) 從背面鎖在轉接卡
上面。
3. 接著裝上 Cache Vault 電源模組,並連
接 42 吋纜線延長線。
4. 然後,將延長線的另一端連接至 Cache
Vault 快閃記憶體模組的插座。
5. 將 PIKE 2208 控制卡裝上擴充槽,再
將轉接卡裝回系統內(如右圖箭頭所
示)。然後將多餘的延長線整理好,
埋入 PIKE 2208 控制卡旁的縫隙中,
完成安裝。
PIKE 2208 卡
若想要了解更多關於如何拆裝轉接卡的步驟,請參考伺服器系統使用手
冊上的說明。
安裝至 ESC4000 G2 GPU 伺服器
1. 取出已裝上 Cache Vault 電源模組鐵件
夾的支架,並於支架側邊鎖上全高鐵
件擋板(使用螺絲(3) 安裝)。
Cache Vault Accessory Kit 快速安裝手冊
15
2. 取出系統內右側的擴充卡支撐架,將
此支架裝入支撐架裡並鎖上一顆螺絲
固定。
若想了解更多關於如何拆裝擴
充卡支撐架的步驟,請參考伺
服器系統使用手冊上的說明。
3. 再將纜線穿過右圖中的走線孔(圈選
處)。
4. 將擴充卡支撐架裝回系統中,並鎖上
螺絲固定。
若想了解更多關於如何安裝轉
接卡的步驟,請參考伺服器系
統使用手冊上的說明。
5. 連接纜線至已裝在 PIKE 2208卡上的
Cache Vault 快閃記憶體模組上面的插
座。
6. 接著如右圖所示,將 PIKE 2208 卡裝
入中央的轉接卡。
7. 最後,請依照伺服器系統使用手冊內
的安裝說明,將轉接卡裝回系統內,
完成安裝。
16
Cache Vault Accessory Kit 快速安裝手冊