860erOM
6/20/06
8:42 PM
Page 3
860 Er Owner’s Manual
860erOM
6/20/06
8:42 PM
Page 4
Purchaser’s Reference Information
IT IS IMPERATIVE THAT YOU FILL IN THE FOLLOWING INFORMATION AND
REFER TO IT SHOULD THE NEED FOR SERVICE ARISE.
Product Name:
Diamondback 860Er Elliptical
Serial Number:
R__________
To Activate Warranty:
SERIAL NUMBER
R0409440001
IIII III IIIII IIIIII
WARNING REMOVING OR ALTERATION
OF THIS LABEL VOIDS WARRANTY
REGISTER YOUR WARRANTY AT
www.diamondbackfitness.com
OR COMPLETELY FILL OUT THE ATTACHED WARRANTY CARD (SEE
BACK COVER) AND RETURN TO DIAMONDACK FITNESS WITHIN
15 DAYS OF THE DATE OF PURCHASE. FAILURE TO COMPLY WITH
THE WARRANTY ACTIVATION PROCEDURE MAY VOID THE MANUFACTURER’S WARRANTY.
Dealer Name:
Serial No. Sticker
Dealer Address:
Dealer Telephone Number: (
)
Dealer Contact Name:
Date Purchased:
Shipping Materials:
Diamondback recommends that you retain the original packing materials
(box and packing items) for future shipping needs.
2
860 Er Owner’s Manual
860erOM
6/20/06
8:42 PM
Page 5
Table of Contents
Purchaser’s Reference Information
Introduction
Safety Instructions and Warnings
Assembly Drawing
Assembly Instructions
Workout Guidelines
Maximum Heart Rate & Training Zone
Quantity & Quality
Heart Rate Monitoring Devices
Pulse hand grips
Chest strap
Console
Glossary of Terms
Default Values
Operating Tips
Console Layout
Displays
Function Keys
Workout Programs
Warm up
Cool Down
Workout Summary
Quick Start
Classic Programs
Manual
Random
Interval
Hill
Strength
HR Interactive Programs
Target HR
HR Interval
Maintenance
Domestic Warranty Information
Warranty Card
860 Er Owner’s Manual
2
4
5
6
7
9
12
13
15
17
19
25
28
29
31
3
860erOM
6/20/06
8:42 PM
Page 6
Introduction
Congratulations on your new 860Er elliptical trainer. You made a very smart
choice. You are about to experience one of the most effective and technically
advanced methods of low-impact, cardiovascular exercise available today.
Your patented 860Er elliptical trainer was created by Diamondback Fitness,
the innovative value leaders in fitness and bicycle equipment for nearly three
decades.
Your power-packed 860Er has feature after feature to make your workout
extremely efficient and comfortable… Features you’ll only find in higher
priced models. Your console offers 5 display windows with easy to select
programming buttons, plus a Polar® Compatible Heart Rate Receiver and
Hand Held Pulse Sensors with 2 Interactive HR programs. You can choose
from 16 levels of intensity including classic Quick Start options and demanding Hill Profile programs. This is a serious piece of equipment that will take
on your most extreme challenges with ease. We worked hard to integrate a
retro sleek design with space-age technology, and we’re proud of our accomplishment.
You can count on your Diamondback Elliptical trainers to provide years of
pleasure and fitness. The solid steel frame, quality construction and technosavvy electronics are guaranteed to provide you with the ultimate workout
experience. Congratulations on choosing an elliptical from America’s premier name in light institutional and home exercising equipment.
For more information or questions regarding your 860Er, please go to our
website at www.diamondbackfitness.com. Or please contact us:
Diamondback Fitness, Inc.
300 Camarillo Ranch Road,
Camarillo, CA 93012
Ph. 800.776.7642
Fax: 805.388.5890
4
860 Er Owner’s Manual
860erOM
6/20/06
8:42 PM
Page 7
Safety Instructions and Warnings
The 860Er is built for optimum safety and is designed to meet or exceed all domestic
and international standards. However, certain precautions need to be followed when
operating any exercise equipment. BE SURE TO READ THE ENTIRE OWNER’S MANUAL BEFORE OPERATING YOUR 860Er UNIT.
CAUTION – FOR SAFE OPERATION
1. Keep your hands and feet away from all moving parts and pinch points. See
figure A for possible pinch points.
2. Before beginning any exercise program on the 860Er equipment, it is
important to consult with your physician if you have any of the following:
History of heart disease, high blood pressure, diabetes, chronic respiratory
diseases, elevated cholesterol, or if you smoke cigarettes or experience any
other chronic diseases or physical complaints.
3. If over the age of 35 or overweight, consult with your physician before
beginning any exercise program.
4. Pregnant women should consult with their physician before beginning an
exercise program.
5. If you experience dizziness, nausea, chest pains or other abnormal
symptoms during exercise, stop the exercise session immediately. Consult
your physician before continue your exercise.
6. Always drink fluids if you exercise for twenty or more minutes on any 860Er unit.
Figure A
• The areas around the footpad &
steparm cover.
WARNING – TO REDUCE RISK OF INJURY TO YOURSELF OR OTHERS
1. To ensure proper functioning of your 860Er equipment, do not install
attachments or accessories not provided or recommended by Diamondback.
2. For proper function, do not insert any objects into any opening of the equipment.
3. Always wear proper clothing and shoes when exercising on your 860Er
unit.
4. User weight is not to exceed 350lbs/155kgs for 860Er.
5. Keep children and pets away from 860Er equipment. Hands and feet may
get caught in the pedals or other moving parts, which could result in serious
injury.
6. Place the 860Er unit in an area that will meet minimum clearance
requirements: Front, Back & Sides: 2 feet/60cm.
7. Place the 860Er equipment away from walls to allow proper ventilation. Air
should be able to circulate freely around the units. Keep all air openings free of
dirt and dust.
8. The 860Er is intended for indoor use in the home environment. It is not
intended for outdoor use.
9. Place your 860Er unit on a solid, level surface when in use. Adjust the leveling
pads if necessary.
10. Use the handlebar when getting on and off your 860Er unit.
11. Make sure all components are fastened securely (i.e. handlebars, handrails,
steparms, footpads) at all times.
12. Do not remove the covers or other components. Only an authorized Diamondback
fitness dealer should perform the service.
13. SAVE THIS OPERATING INSTRUCTIONS MANUAL FOR YOUR REFERENCE.
860 Er Owner’s Manual
5
860erOM
6/20/06
8:42 PM
Page 8
Assembly Drawing
6
860 Er Owner’s Manual
860erOM
6/20/06
8:42 PM
Page 9
Assembly Instructions
Please take the assembly hardware out of the hardware package box. Lay all
the hardware out and take note for its locations. Follow the assembly instruction step by step to complete the assembly.
Step 1: Leveling Pads
1. Insert the leveling pads into the front stabilizer bar and adjust them as
necessary, to ensure your equipment is leveled with floor.
Step 2: Console Mast Assembly
1. Install console mast by carefully sliding it onto console mast receptor.
2. Insert 2pcs of M10 x 95mm bolts with lock washers and flat washers through
the lower set of holes on the receptor, into the console mast and to the
welded nuts. Hand tightens them first.
3. Insert 2pcs of M10 x 95mm bolts with flat washers through the upper set of
holes on the receptor, into the console mast and to the welded nuts. Hand
tightens them too.
4. Finally tighten all 4 sets of bolts with attached open-end wrench.
5. Connect the plug of the main wire harness, coming out of the console mast,
to the plug receptor coming out of base frame, taking care to install correctly.
(See plug alignment marks)
6. Store the excess harness back into the console mast and base frame. This will
keep the slack out of harness so that the wires will not pinched and short out.
Use the attached ty-warps to tighten down the wire harness onto console mast
and base frame.
7. Place console mast covers correctly in place (See R and L marks inside), and
align them with each other.
8. Insert and tighten console mast cover with two screws (M5 x 8mm) using a
Phillips screwdriver.
Step 3: Handrail Assembly
1. Attach right handrail (see the R mark on the handrail) onto the console mast
at the right handrail axle.
2. Next, attach the right handrail to the right steparm. Insert the
handrail/steparm axle through the hole in the steparm and through the tube
at the bottom of handrail. Insert a M8 x 20 screw with lock washer into
steparm axle and tighten it using an Allen wrench and an open-end wrench
on each side.
3. Insert the set-screw collar onto the handrail axle and tighten it with 2 set
screws, using attached Allen wrench. Please make sure there is no extra play
for the handrail.
4. Assemble left handrail the same way as assembly the right handrail
Step 4: Handrail & Steparm Covers Assembly
1. Attach a set of steparm covers onto steparm using 2pcs of M5 x 8mm screws
and a Phillips screwdriver.
2. Attach a set of handrail covers onto handrail using 2pcs of M4 x40mm
860 Er Owner’s Manual
7
860erOM
6/20/06
8:42 PM
Page 10
Assembly Instructions
screws and nuts, using a Phillips screwdriver.
3. Repeat the process of item 1 and 2 for the other side.
Step 5: : U Handlebar Assembly
1. Insert the hand pulse harness through the opening of the console mast and
out of the console mounting plate.
2. Assemble the handlebar onto the mount and insert and tighten the two M8 x
35mm screws using an Allen wrench. Be sure not to pinch the hand pulse
harness during this procedure, as this will damage the electronic console.
Step 6: Console Assembly
1. Connect both plugs, from main wire harness and hand pulse harness, to the
plug receptors on the backside of the console, taking care to install correctly
(see plug alignment marks).
WIRING HARNESS INSTALLATION HINT: Any excess wiring must be carefully
inserted (“stored”) back into the console mast before installing the console
onto the console mounting plate.
2. Fasten the console to the console mounting plate with the four M5 x 12mm
screws and washers, using a Philips screwdriver
Step 7: Transformer Assembly
1. Plug the transformer into plug receptor located on the rear/bottom side of the
middle case.
2. Plug the transformer output into power outlet. NOTE: Be sure to use right
transformer for your power outlet, 110V or 220V.
Step 8: Water bottle
1. Place the water bottle into the water bottle holder.
8
860 Er Owner’s Manual
860erOM
6/20/06
8:42 PM
Page 11
Workout Guidelines
Good health is an exercise in common sense
The Surgeon General released a new study in 2001, The Surgeon General’s Call
To Action To Prevent and Decrease Overweight and Obesity. It indicates that 61%
of American adults are either overweight or obese. The story states that overweight
increases the risk of health problems, such as heart disease, certain type of cancer,
type 2 diabetes, etc. It further points out that overweight needs to be regarded primarily as a Health rather than as an Appearance issue.
The Surgeon General’s Healthy weight advice for consumers is:
1. Aim for a healthy weight: Find your Body Mass Index (BMI) on the chart below.
2. Be active: Keep physically active to balance the calories you consume.
3. Eat well: Select sensible portion sizes.
BMI = (weight (lb) ÷ height2 (in)) x 703
Weight in Pounds
Height in Feet and Inches
120 130 140 150 160 170 180 190 200 210 220 230 240 250
4’6
4’8
4’10
5’0
5’2
5’4
5’6
5’8
5’10
6’0
6’2
6’4
6’6
6’8
29
27
25
23
22
21
19
18
17
16
15
15
14
13
31
29
27
25
24
22
21
20
19
18
17
16
15
14
34
31
29
27
26
24
23
21
20
19
18
17
16
15
36
34
31
29
27
26
24
23
22
20
19
18
17
17
Healthy Weight
39
36
34
31
29
28
26
24
23
22
21
20
19
18
41
38
36
33
31
29
27
26
24
23
22
21
20
19
43
40
38
35
33
31
29
27
26
24
23
22
21
20
46
43
40
37
35
33
31
29
27
26
24
23
22
21
Overweight
48
45
42
39
37
34
32
30
29
27
26
24
23
22
51
47
44
41
38
36
34
32
30
28
27
26
24
23
53
49
46
43
40
38
36
34
32
30
28
27
25
24
56
52
48
45
42
40
37
35
33
31
30
28
27
25
58
54
50
47
44
41
39
37
35
33
31
29
28
26
60
56
52
49
46
43
40
38
36
34
32
30
29
28
Obese
Note: This chart is for adults (aged 20 years and older).
Heart rate is an important key to your exercise.
The Surgeon General also released a report on physical activity and health. This
report definitively stated that exercise and fitness are beneficial for a person’s
health and redefined that exercise is a key component of disease prevention and
healthier living.
Medical research has shown us that there is an amount of exercise, which is
enough to condition the cardio respiratory system and the muscles of the body.
This amount of exercise is between 60% and 85% of your maximum heart rate
measured during a training session. This range allows enough exercise to achieve
860 Er Owner’s Manual
9
860erOM
6/20/06
8:42 PM
Page 12
Workout guidelines (continued)
fitness, but not an excessive amount to cause injury. Your heart rate is an excellent
indicator of the amount of stress placed on the cardiovascular system. Taking full
advantage of this information, the 860Er is designed to include heart rate monitoring features.
If exercise intensity is too low or too high, no gains will be made in fitness. If the
intensity is too low, the stress levels are ineffective. If the intensity is too high, injury
or fatigue may set your exercise program back as you try to recover.
Heart Rate Guidelines
60% - 85% Maximum Target
Ages in years
The best way to monitor exercise intensity is to accurately count your pulse during
exercise. Your heart rate can easily be determined by counting your pulse at the
chest, wrist or at the carotid artery on your neck. It is difficult to count your own pulse
during exercise, mainly because you cannot count fast enough to get an accurate
number. The 860Er is equipped with a wireless telemetry receiving system. What it
does is automatically count your heart rate while you are wearing a heart rate chest
belt during your exercising period. Heart rate is monitored and electronically displayed as a digital readout. Your target heart rate, the intensity needed to improve
cardiovascular fitness, depends primarily on your age and not your state of fitness.
It is calculated as a percentage of your maximum heart rate, estimated as 220 minus
your age. It is most effective to train at your target heart rate between 60% and
85% of your maximum heart rate.
▲ = 85% ■ = 60%
Typical Target Zone Exercise
Patterns for 35 year-old
Maximum Heart Rate & Training Zone
To calculate your maximum heart rate and find your training zone, use the following formula. An example has been provided below based for a 35-year
–old person:
220 – Age = Maximum Heart Rate
60% of Maximum Heart Rate
85% of Maximum Heart Rate
Training Zone:
(220 – 35 = 185)
(60% x 185 = 111bpm)
(85% x 185 = 157bpm)
111bpm – 157bpm
Note: Always enter your age into the console before you exercise to
keep the % of your maximum heart rate accurate.
Quantity & Quality
It is recommended that you accumulate at least 30 minutes of physical activity most
days of the week. Physical activity should be initiated slowly and the intensity
should be increased gradually. You should select activities that you enjoy and can
fit into your daily life. Having Diamondback equipment at home certainly gives you
the comfortable and convenient workout you want.
The American College of Sports Medicine makes the following recommendations
for the quantity and quality of training for developing and maintaining cardio respiratory fitness in healthy adults:
• An activity that uses large muscle groups, maintained continuously, and is
rhythmical and aerobic in nature.
• Duration: 20 to 60 minutes of continuous aerobic activity, including a
warm-up and cool-down period for each exercise session.
10
860 Er Owner’s Manual
860erOM
6/20/06
8:42 PM
Page 13
Workout guidelines (continued)
• Frequency: 3 to 5 times per week.
• Intensity: 60% to 85% of maximum heart rate.
• In addition to aerobic exercise, it is recommended that you add strength
training of moderate intensity twice per week to your program.
Get a smart start on exercising.
Anyone over the age of 35, as well as younger persons whom are overweight,
should check with his/her physician before beginning any type of exercise program. People who have diabetes or high blood pressure, a family history of
heart disease, high cholesterol or have lead a sedentary lifestyle should protect
themselves with a medical check-up and a stress test, preferably administered
during exercise by a healthcare professional.
1. Always stretch before your workout to loosen muscles, and afterwards to cool
down.
2. The first few minutes of your workout should be devoted to warming up muscles
before a vigorous workout, and building your heart rate slowly.
3. After your aerobic workout of about 24-32 minutes, spend 10 minutes
gradually reducing your heart rate with a lower resistance level.
Remember, to start slow, with intensity low, until you build endurance and strength.
And always consult your physician before beginning any exercise program.
860 Er Owner’s Manual
11
860erOM
6/20/06
8:42 PM
Page 14
Heart Rate Monitoring Devices
Pulse Hand Grips (Standard)
The 860Er unit is heart rate controlled and comes standard with stainless steel pulse handgrips. To activate, gently grasp both handgrips to obtain a heart rate reading.
(Note: It is recommended to wear a chest strap for Heart Rate control program, as it is more
accurate. If you wear a chest strap and use hand grips at the same time for heart rate monitoring purpose, please note the console will take the measurement of the chest strap.)
Operating Tips:
If you are not getting a consistent reading while using the hand pulse option, we recommend the following suggestions:
• Make sure that the palms of the hands are touching the contact area of each
hand pulse grip.
• Maintain an even pressure on the grips.
• Do not hold the hand pulse grips too tightly.
Chest Strap (Standard)
The 860Er is equipped a built-in receiver and a chest strap for your heart rate monitoring. To get an accurate reading using these devices, you will need to be within three
feet of the console, and a minimum of four feet from others using a heart rate monitoring device.
(Note: The transmitter may fluctuate erratically if you are too close to other heart rate
monitoring equipment or there is other electronics near by, such as TV, Radio...)
The receiver of the wireless ECG system is built into the console unit of the Diamondback
860Er equipment. While using heart rate control modes, the computer monitors the
exact measurement of and control over the activity if the heart. Heart rate frequency is
displayed while the computer continually compares heart rate to the preprogrammed
personal data. The computer adjusts the wattage to maintain heart rate at the preprogrammed level.
How to Wear Your Sensor/ Transmitter
1. Buckle one end of the chest strap onto the transmitter.
2. Adjust the band length so that the fit is snug, but not too tight.
3. Buckle the other end of the chest strap onto the transmitter.
4. Center the transmitter on your chest below the pectoral muscle (breasts).
5. Stretch the transmitter away from your chest and moisten the conductive electrode
strips located next to the buckles with water.
(Note: The transmitter is on automatically when being worn. It is off when it is not connected to your body. However, as moisture may activate the transmitter, thoroughly dry
the transmitter to prolong battery life.)
Erratic Heart Rate Readings:
Erratic readings on the receiver can be caused by electromagnetic disturbances. If the heart
rate readings appear to be abnormal, check that your 860Er product is not within range
of other strong electromagnetic signals. Common sources are televisions, computers, cars,
cell phones, TV antennas and high voltage power lines (both above and below ground).
Please note: Static electricity in clothing or a flapping shirt can cause electrical interference,
so some items of clothing, i.e. man-made fibers, can also be the cause. Please try wetting
the t-shirt in the area where the transmitter is.
If the battery of the transmitter is running low, the transmission range decreases and may
cause errors similar to the ones listed above in this document
Battery Replacement:
To replace the transmitter battery, remove the four small screws securing the cover plate in
the back of the transmitter. Remove the cover plate, and the thin plastic shield covering the
battery, Remove the battery and replace with a new CR 2032 battery (available at photo
or watch departments). Make sure the battery snaps into place and the numbers are facing up. Replace the plastic shield and cover plate with four screws.
12
860 Er Owner’s Manual
860erOM
6/20/06
8:42 PM
Page 15
Console
Glossary of Terms
• Idle mode = Console is reset and waiting for an entry. The dot matrix display
window will flash “DB”. If no rpm for 5 minutes, the console will enter power
save mode and the display will be shut off.
• LED = The lights on the face of the console.
• Watts = The rate of energy currently being expended.
• Work = The amount of energy expended during exercise.
• Level = The resistance provided by this elliptical. The resistance gradually
increases as the level goes up.
• Difficulty level = In the preset programs, the intensity of the program is
designed into an intensity hill profile with default difficulty level 1. You may
select a different difficulty level to increase or decrease the hill profile.
Default Values
• Age = 35 years
• Weight = 155 lb or 70kg for Metric system
• Time = 30 minutes; Segment time = 30/16 minutes.
• Intensity level: Level 1.
• Difficulty level for intensity: Level 1
Note: Every time age or weight is changed, the default value setting will be
updated to the last modification.
Operating Tips
• Power On:
In the power save mode, press any key or start pedaling to wake up the
console and start operation.
• Reset:
To reset a program during its operation, press and hold the “Stop/Reset” key
for 2 seconds. When the program resets, the console returns to idle mode.
• Pause and Resume: You may interrupt or pause a program for up to 5 minutes
during a workout before the console resets. To pause a program, simply stop
pedaling. To resume the program back to the point of where you left off,
either press Start or simply start pedaling.
• Switching a program:
The user may switch from current operating program to another program
during its execution by pressing a new program key and then Enter key to
accept the new program. Calories and distance will continue accumulating
from previous program. If “Classic Program” or “HR Interactive” program key
is pressed during a program-executing mode, it will enter program-switching
mode:
– If Enter key is indented, it will enter this program setup mode. Age and
weight default will be the last update and time will be the remaining time
of the pervious program.
– If Start key is indented, the new program will begin, but Warm Up mode
will be skipped.
– If 10 seconds passes and no other key is indented, the program will
860 Er Owner’s Manual
13
860erOM
6/20/06
8:42 PM
Page 16
Console (continued)
resume back to previous activities.
• Re-start a program:
The user may re-start a program after the program ends. Simply press “Start”
key during Cool Down or Workout Summary mode. The program will be
started right immediately without Warm up. The program default will remain
the same as previous program; the calories and distance will continue
accumulating.
• Level adjustment:
During Quick Start, Manual & Interval program, the user may press Level
Up/Down key to adjust the resistance level. (Note: Resistance adjustments are
not allowed in any Heart rate interactive program).
– If Level Up/Down key is pressed, the level data display will show the
current resistance level and adjust it accordingly. The Dot matrix display
will update the profile as well.
• Difficulty level adjustment:
During Random, Hill & Strength profile program, the user may press Level
Up/Down key to adjust the difficulty level.
– If Level Up/Down key is pressed, the level data display will show the
current resistance level and adjust it accordingly. The Dot matrix display
will update the profile as well.
• % MAX HR: Pulse / (220 minus age):
It is recommended to control your % Max heart rate within 60% – 85% for
the most effective workout. It is also unsafe to exceed 90% and above. This
elliptical is equipped with a safety shut off function.
– First, there is a warning for exceeding 90%, the Pulse data display will
blink.
– Second, if the heart rate continues going up and reaches 95% for 5
seconds, the console will reset.
•
14
English / Metric setting: The default Units is English system. To enter the
system-switching mode, press “ Start” & “Stop” keys at the same time for 2
seconds during idle mode. The Dot Matrix display will blink “EN” for English
units or “ME” for Metric units. To change it, press “Level Up/Down” key to
switch the current Units. After the setup is completed, press “Stop” key for 2
seconds to reset the console and return to the idle mode.
860 Er Owner’s Manual
860erOM
6/20/06
8:42 PM
Page 17
Console Layout
860 Er Owner’s Manual
15
860erOM
6/20/06
8:42 PM
Page 18
Console Layout (continued)
Displays
a. Dot Matrix /Profile display
Dot Matrix/Profile
display
Workout data
Display
1. It displays letters for instruction during setup:
• Display “AGE” during age setup; “WT” for weight setup; “TM” for time setup
& “HR” for HR setup.
• Display “EN” or “ME” for English or Metric units switch.
• Scroll “WARM UP” or “COOL DOWN” to indicate entering these modes.
2. It displays the program profile during the program execution.
• Display the level profile during the Classic programs.
• Display the % Max HR profile during the HR interactive programs.
3. Profile definitions:
• Level profile – The LED represents the resistance level, L1- L16; the higher LED
lights up, the higher resistance it is on. The LED will blink to indicate the
current workout segment.
• % Max HR profile – The LED represents the % Max HR: 0-100%.
b. Workout data display
As soon as a program is executed, it will start displaying the default 3 workout data: calories,
speed & level. You may select your favorite data displays by pressing the “SELECT” button on
the right hand side, the LED indicator will light up to show which row of data is displaying.
• Calories (kcal): Total workout calories.
• Watts (watt): Current workout wattage.
• Speed (mile/hr or km/hr): Current workout speed. It simulates a jogging
exercise.
• Distance (mile or km): Total workout distance. It simulates a jogging exercise.
Intensity (level 1-16): Current workout level.
• RPM: Revolutions per minute.
c. Time & Pulse displays
1. In the program setup, Pulse window will light up and display the default Age,
Weight & HR for adjustment. Time display will light up and display the default
Time for adjustment.
2. As soon as the program is executed, it will start displaying Time and Pulse.
• Time (hr: min or min: sec): The remaining of current program time.
• Pulse (bpm): Your current heart rate. If there is no pulse detected, it will
display “ - - - “ instead.
Function Keys
Time & Pulse
Display
a. Level Up/Down keys:
• During program setup, press “Level Up/Down key” to adjust the following –
age, weight, time & HR setting.
• After program started, press “Level Up/Down key” to adjust the level,
difficulty level or HR setting during exercising.
b. Enter key:
• After program selecting, press “Enter” to accept the program and enter its
setup mode.
• After age, weight, level….. adjustment, press “Enter” key to accept your entry.
Function Keys
c. Start key:
• Press “Start” to start a program during program setup.
• Press “Start” key to skip Warm up and enter program executing.
• Press “Start” to re-start a program during Cool Down.
d. Stop/Reset key:
• Press and hold “Stop” button to reset the console.
• Press “Stop” to end program executing and enter Cool Down.
• Press “Stop” to enter workout summary during Cool Down
16
860 Er Owner’s Manual
860erOM
6/20/06
8:42 PM
Page 19
Workout Programs
Getting Started
The 860Er automatically initiates a 3-minute Warm Up at the beginning of each program. It is designed to prepare your body for an intensive workout and to reduce the
possibility of injury during workout.
Note: Warm Up is skipped for the Quick Start or Manual program.
Beginning the Program
Warm Up is active as soon as the “Start” key is pressed and a program is executed.
The Dot matrix window will scroll “WARM UP” and then display program profile. This
sequence will repeat until Warm up is finished.
During the Program
Data Display
• Once it is started, the data display window will display the default workout
data of “calories, speed & level”. Press “Select” button to switch the data dis
plays to “watts, distance & RPM”.
• The time will display count down from 3:00.
• The pulse display will display the heart rate if there is valid pulse detected.
.
Adjustment
• Level = L1. Press “Level Up/Down” key to adjust the level from L1- L5 only.
• “Start” key can be pressed to skip the warm up and start the program
immediately.
Ending the Program
• When 3-minute duration is up or Start key is pressed, Warm Up will end and
the program will execute.
• There will be a beep sound to indicate the Warm up is over and the selected
program begins.
Pause, Reset, Switch or Save a program
• See Console Operating Tips section for details, page 13.
Getting Started
860Er is equipped with a 3-minute Cool Down at the end of each program. It appears
as soon as a program ends. Cool Down is designed to reduce muscle stiffness and
allow your heart rate to recover.
Beginning the Program
Cool Down is active as soon as a program ends. The dot matrix window will scroll
“COOL DOWN” and then display program profile. This sequence will repeat until Cool
Down is finished.
During the Program
Data Display
• Once it is started, the data display window will display the default workout
data of “calories, speed & level”. Press “Select” button to switch the data
displays to “watts, distance & RPM”.
860 Er Owner’s Manual
17
860erOM
6/20/06
8:42 PM
Page 20
Workout Programs
•
•
The time will display 3:00” and start counting down .
The pulse display will display the heart rate if there is valid pulse detected.
.
Adjustment
• Level = L1. Press “Level Up/Down” key to adjust the level from L1- L5 only.
• “Start” key could be pressed to re-start the previous program again.
• “Stop” key could be pressed to skip the cool down mode and active the
Workout Summary immediately.
Ending the Program
• When 3-minute duration is up or Stop key is pressed, Cool Down will end and
enter Workout Summary. See Workout summary for details.
.
Pause, Reset, Switch or Save a program
• See Console Operating Tips section for details, page 13.
Getting Started
For your convenience, the 860Er incorporates a Workout Summary right after the completion of the Cool Down. It will display the total workout data for 30 seconds before
the Console resets.
Beginning the Program
Workout Summary appears as soon as the Cool Down mode ends or a “Stop” key is
pressed during Cool Down mode. The data display will stop counting and show the
final data.
During the Program
Data Display
• Once this summary is started, the data window will display:
– Calories: total calories.
– Distance: total distance.
– Time: total program time.
Adjustment
Intensity cannot be adjusted during this time.
Ending the Program
• When 30-second duration is up, Workout Summary will end and console will
reset.
Pause, Reset, Switch or Save a program
• See Console Operating Tips section for details, page 13.
18
860 Er Owner’s Manual
860erOM
6/20/06
8:42 PM
Page 21
Workout Programs (continued)
Getting Started
A Quick Start program is for someone who wants to bypass the setup mode and start
their workouts right away. By picking Quick Start program, you are accepting the
default values for calculations. Be sure to include a Warm Up period during your workout since the Warm Up mode is skipped in the Quick Start program.
Beginning the Program
During idle mode, the dot matrix window displays ”DB”. To begin this program, press
“Quick Start” key once or continue to pedal and press no key for 30 seconds.
Program Default Values
• Time = 30 minutes
• Level = L1
Quick Start
Key
During the Program
Data Display
• As soon as the “Quick Start” button is pressed, this program will begin; the
data display window will display the default workout data of “calories, speed
& level”. Press “Select” button to switch the data displays to “watts, distance &
RPM”.
• Time display will show 00:00 and count up.
• Pulse display will start displaying if there is a valid pulse.
.
Adjustment
• Press “Level Up/Down” key to adjust the level from L1 to L16. The level data
display will update the level and the dot matrix window will update the profile
accordingly.
Ending the Program
• When 30-minute duration is up or Stop key is pressed, this program will end
and Cool down will be active. See Cool down section for details.
• There will be a beep sound to indicate the program ended.
Pause, Reset, Switch or Save a program
• See Console Operating Tips section for details, page 13.
Getting Started
You could build your own profile with Manual program. Be sure to include a Warm
Up period during your workout since the Warm Up mode is skipped in the Manual
program.
Classic Program
Display
Beginning the Program
During idle mode, the dot matrix window displays ”DB”. To begin this program, press
“Classic Program” key until “Manual” program LED indicator lights up.
Accepting default values or Entering the program setup mode
When the dot matrix display shows Manual program profile, it indicates you are about
860 Er Owner’s Manual
19
860erOM
6/20/06
8:42 PM
Page 22
Workout Programs (continued)
to select the Manual program:
• Press “Start” key to accept current default values and begin Manual program
workout.
– Default Time = 30 minutes
– Default Level = L1.
• Or press “Enter” to enter program setup mode. The dot matrix & data displays
will take you through the program setup mode step by step as below:
Entering Age
1. If Enter key is pressed, the dot matrix window will flash “AGE”.
2. The pulse display will display & blink the default age.
3. You may press “Level Up/Down” key to adjust the age.
4. After age adjustment, press “Enter” to accept and enter Weight adjustment.
Entering Weight
1. If Enter key is pressed after age adjustment, the dot matrix window will flash “WT”.
2. The pulse display will display & blink the default weight.
3. You may press “Level Up/Down” key to adjust the weight.
4. After weight adjustment, press “Enter” to accept and enter Time adjustment.
Entering Time
1. If Enter key is pressed after weight adjustment, the dot matrix window will flash
“TM”.
2. The time display will display & blink the default time = 30:00.
3. You may press “Level Up/Down” key to adjust the time up to 99:00.
4. After time adjustment, press “Enter” or “Start” to accept and begin this program.
(Note: you may press Start key anytime to skip the setup and begin the workout immediately.)
During the Program
As soon as the “Enter” or “Start” key is pressed, the Manual program will start.
Data Display
• Once the program is started, this program will begin; the data display window
will display the default workout data of “calories, speed & level”. Press “Select”
button to switch the data displays to “watts, distance & RPM”.
• Time display will show the selected program time and count down.
• Pulse display will start displaying if there is a valid pulse.
Adjustment
• Press “Level Up/Down” key to adjust the level from L1 to L16. The level data
display will update the level and the dot matrix window will update the profile
accordingly.
Ending the Program
• When selected program time is up or Stop key is pressed, this program will
end and Cool down will be active. See Cool down section for details.
• There will be a beep sound to indicate the program ended
Pause, Reset, Switch or Save a program
See Console Operating Tips section for details, page 13.
20
860 Er Owner’s Manual
860erOM
6/20/06
8:42 PM
Page 23
Workout Programs (continued)
Getting Started
The Random program is designed to allow the user to choose from an unlimited number of computer generated profiles.
Beginning the Program
During idle mode, the dot matrix window displays ”DB”. To begin this program, press
“Classic Program” key until “Random” program LED indicator lights up.
Accepting default values or Entering the program setup mode
When the dot matrix display shows Random program profile, it indicates you are about
to select the Random program:
• Press “Start” key to accept current default values and begin Random program
workout.
– Default Time = 30 minutes
– Default Level = a computer generated level profile with default difficulty
level = L1.
• Or press “Enter” to enter program setup mode The dot matrix & data displays
will take you through the program setup mode step by step as below: (same as
Manual program setup)
– Enter Age
– Enter Weight
– Enter Time
During the Program
As soon as the “Enter” or “Start” key is pressed, the Warm Up will be active. See Warm
Up mode section for details.
Data Display
• When Warm Up mode is completed, the data display window will display the
default workout data of “calories, speed & level”. Press “Select” button to switch
the data displays to “watts, distance & RPM”.
• Time display will show the selected program time and count down.
• Pulse display will start displaying if there is a valid pulse.
Adjustment
• Press “Level Up/Down” key to adjust the difficulty level. The level data display
will update the level and the dot matrix window will update the profile
accordingly.
Ending the Program
• When selected program time is up or Stop key is pressed, this program will end
and Cool down will be active. See Cool down section for details.
• There will be a beep sound to indicate the program ended.
Pause, Reset, Re-start or Switch a program
See Console Operating Tips section for details, page 13.
860 Er Owner’s Manual
21
860erOM
6/20/06
8:42 PM
Page 24
Workout Programs (continued)
Getting Started
The Interval program helps to build the strength of your cardiovascular system. By
alternating the workload from high to low, your heart gets an effective workout.
Beginning the Program
During idle mode, the dot matrix window displays ”DB”. To begin this program, press
“Classic Programs” key until “Interval” program LED indicator lights up.
Accepting default values or Entering the program setup mode
When the dot matrix display shows Interval program profile, it indicates you are about
to select the Interval program:
• Press “Start” key to accept current default values and begin Interval program
workout.
– Default Time = 30 minutes
– Default Level = a default level profile alternates Rest: L2 and Work
level: L10.
• Or press “Enter” to enter program setup mode The dot matrix & data displays
will take you through the program setup mode step by step as below: (same as
Manual program setup)
– Enter Age
– Enter Weight
– Enter Time
During the Program
As soon as the “Enter” or “Start” key is pressed, the Warm Up will be active. See Warm
Up mode section for details.
Data Display
• When Warm Up mode is completed, the data display window will display the
default workout data of “calories, speed & level”. Press “Select” button to switch
the data displays to “watts, distance & RPM”.
• Time display will show the selected program time and count down.
• Pulse display will start displaying if there is a valid pulse.
Adjustment
• Press “Level Up/Down” key during Rest segment to adjust the level from L2. The
level of the remaining Rest segments will be updated to the new setting and the
dot matrix window will update the intensity profile accordingly as well.
• Press “Level Up/Down” key during Work segment to adjust the level from L10.
The level of the remaining Work segments will be updated to the new setting
and the dot matrix window will update the intensity profile accordingly as well.
Ending the Program
• When selected program time is up or Stop key is pressed, this program will end
and Cool down will be active. See Cool down section for details.
• There will be a beep sound to indicate the program ended.
Pause, Reset, Re-start or Switch a program
See Console Operating Tips section for details, page 13.
22
860 Er Owner’s Manual
860erOM
6/20/06
8:42 PM
Page 25
Workout Programs (continued)
Getting Started
The Hill program simulates a hill climb exercise with a preset hill profile. The exercise profile will guide you through the up hill climb or down hill glide.
Beginning the Program
During idle mode, the dot matrix window displays ”DB”. To begin this program, press
“Classic Programs” key until “Hill” program LED indicator lights up.
Accepting default values or Entering the program setup mode
When the dot matrix display shows Hill program profile, it indicates you are about to
select the Hill program:
• Press “Start” key to accept current default values and begin Hill program
workout.
– Default Time = 30 minutes
– Default Level = a preset level profile with default difficulty level = L1.
• Or press “Enter” to enter program setup mode The dot matrix & data displays
will take you through the program setup mode step by step as below: (same as
Manual program setup)
– Enter Age
– Enter Weight
– Enter Time
During the Program
As soon as the “Enter” or “Start” key is pressed, the Warm Up will be active. See Warm
Up mode section for details.
Data Display
• When Warm Up mode is completed, the data display window will display the
default workout data of “calories, speed & level”. Press “Select” button to switch
the data displays to “watts, distance & RPM”.
• Time display will show the selected program time and count down.
• Pulse display will start displaying if there is a valid pulse.
Adjustment
• Press “Level Up/Down” key to adjust the difficulty level. The level data display
will update the level and the dot matrix window will update the profile
accordingly.
Ending the Program
• When selected program time is up or Stop key is pressed, this program will end
and Cool down will be active. See Cool down section for details.
• There will be a beep sound to indicate the program ends.
Pause, Reset, Re-start or Switch a program
See Console Operating Tips section for details, page 13.
860 Er Owner’s Manual
23
860erOM
6/20/06
8:42 PM
Page 26
Workout Programs (continued)
Getting Started
The Strength program gradually increases the workload over time. This program
focuses on strengthening both your heart and your major muscle groups.
Beginning the Program
During idle mode, the dot matrix window displays ”DB”. To begin this program, press
“Classic Programs” key until “Strength” program LED indicator lights up.
Accepting default values or Entering the program setup mode
When the dot matrix display shows strength program profile, it indicates you are about
to select the Strength program:
• Press “Start” key to accept current default values and begin Strength program
workout.
– Default Time = 30 minutes
– Default Level = a preset level profile with default difficulty level = L1.
• Or press “Enter” to enter program setup mode The dot matrix & data displays
will take you through the program setup mode step by step as below: (same as
Manual program setup)
– Enter Age
– Enter Weight
– Enter Time
During the Program
As soon as the “Enter” or “Start” key is pressed, the Warm Up will be active. See Warm
Up mode section for details.
Data Display
• When Warm Up mode is completed, the data display window will display the
default workout data of “calories, speed & level”. Press “Select” button to switch
the data displays to “watts, distance & RPM”.
• Time display will show the selected program time and count down.
• Pulse display will start displaying if there is a valid pulse.
Adjustment
• Press “Level Up/Down” key to adjust the difficulty level. The level data display
will update the level and the dot matrix window will update the profile
accordingly.
Ending the Program
• When selected program time is up or Stop key is pressed, this program will end
and Cool down will be active. See Cool down section for details.
• There will be a beep sound to indicate the program ends.
Pause, Reset, Re-start or Switch a program
See Console Operating Tips section for details, page 13.
24
860 Er Owner’s Manual
860erOM
6/20/06
8:42 PM
Page 27
Workout Programs (continued)
Dot matrix display during HR Interactive programs – The dot matrix display will display program % Max HR profile, not level profile. The row of target % Max HR LEDs
will light up to indicate your goal; then the current segment LEDs will light up and
blink to show your actual heart rate. You could compare your actual heart rate
against your goal while exercising.
HR Interactive
Programs
Getting Started
The Target Heart Rate program is designed to keep you training at your chosen heart
rate level. Computer will adjust the intensity level automatically to ensure the target heart
rate is achieved and maintained during the entire program.
A HEART RATE MONITORING DEVICE MUST BE USED FOR THIS
PROGRAM. FOR BETTER RESULTS, A CHEST STRAP IS RECOMMENDED
FOR THIS OPERATION.
IMPORTANT: It is unsafe to exceed 95% of your maximum heart rate
while exercising. Please consult your physician before performing any
Heart Rate based training program
.
Beginning the Program
During idle mode, the dot matrix window displays ”DB”. To begin this program, press
“HR Interactive” key until “Target HR” program LED indicator lights up.
Accepting default values or Entering the program setup mode
When the dot matrix display shows Target HR program profile, it indicates you are
about to select the Target HR program:
•
•
Press “Start” key to accept current default values and begin Target HR program
workout.
– Default Time = 30 minutes
– Default Target HR = 120bpm.
Or press “Enter” to enter program setup mode. The message display will take
you through the program setup mode step by step as below:
– Enter Age
– Enter Weight
– Enter Time
– Enter Target HR
1. If Enter key is pressed after time adjustment, the dot matrix window will
flash “HR”.
2. The pulse display will display & blink the default target HR = 120.
3. You may press “Level Up/Down” key to adjust the target HR up to 85%
of Max HR.
4. After HR adjustment, press “Enter” or “Start” to accept and begin this
program.
(Note: you may press Start key anytime to skip the setup and begin the
workout immediately.)
860 Er Owner’s Manual
25
860erOM
6/20/06
8:42 PM
Page 28
Workout Programs (continued)
During the Program
As soon as the “Enter” or “Start” key is pressed, the Warm Up will be active. See Warm
Up mode section for details.
Data Display
• When Warm Up mode is completed, the data display window will display the
default workout data of “calories, speed & level”. Press “Select” button to switch
the data displays to “watts, distance & RPM”.
• Time display will show the selected program time and count down.
• Pulse display:
– If there is no pulse input, the Pulse data display will show “ - - -“ and blink.
If there continues to be no pulse input, this console will maintain its current
resistance setting and not changing until the program ends or is changed.
– If there is a valid pulse, the Pulse display will show the actual pulse reading.
Adjustment
• Press “Level Up/Down” key to adjust the target HR setting. The Pulse window
will blink the target HR setting and adjust. Until the adjustment is done, it then
will resume to display actual HR. Dot matrix window will update the % Max HR
profile accordingly.
Ending the Program
• When selected program time is up or Stop key is pressed, this program will end
and Cool down will be active. See Cool down section for details.
• There will be a beep sound to indicate the program ended.
Pause, Reset, Re-start or Switch a program
See Console Operating Tips section for details, page 13.
Getting Started
The Heart Rate Interval program is designed to alternate periods of hard work (Work
phase) with periods of easy work (Rest phase). The console will adjust the resistance
level up to meet your Work heart rate goal and adjust it down to recover. This phase
changes every 2 segments to best condition your cardiovascular system.
A HEART RATE MONITORING DEVICE MUST BE USED FOR THIS
PROGRAM. FOR BETTER RESULTS, A CHEST STRAP IS RECOMMENDED
FOR THIS OPERATION.
IMPORTANT: It is unsafe to exceed 95% of your maximum heart rate
while exercising. Please consult your physician before performing any
Heart Rate based training program
.
Beginning the Program
During idle mode, the dot matrix window displays ”DB”. To begin this program, press
“HR Interactive” key until “HR Interval” program LED indicator lights up.
Accepting default values or Entering the program setup mode
When the dot matrix display shows HR Interval program profile, it indicates you are
26
860 Er Owner’s Manual
860erOM
6/20/06
8:42 PM
Page 29
Workout Programs (continued)
about to select the HR Interval program:
•
•
Press “Start” key to accept current default values and begin HR Interval program
workout.
– Default Time = 30 minutes
– Default Work HR = 150bpm, Rest HR = 120bpm.
Or press “Enter” to enter program setup mode. The message display will take
you through the program setup mode step by step as below:
– Enter Age
– Enter Weight
– Enter Time
– Enter Rest HR
1. If Enter key is pressed after time adjustment, the Rest HR setting columns
of dot matrix window will blink.
2. The pulse display will display & blink the default Rest HR = 120.
3. You may press “Level Up/Down” key to adjust the Rest HR up to 80% of
Max HR.
4. After Rest HR adjustment, press “Enter” to accept and begin this
program.
– Enter Work HR
1. If Enter key is pressed after Rest HR adjustment, the Work HR setting
columns of dot matrix window will blink.
2. The pulse display will display & blink the default Work HR = 150.
3. You may press “Level Up/Down” key to adjust the Work HR from “Rest
HR setting” to “85% of Max HR”.
4. After Work HR adjustment, press “Enter” or “Start” to accept and begin
this program.
(Note: you may press Start key anytime to skip the setup and begin the
workout immediately.)
During the Program
As soon as the “Enter” or “Start” key is pressed, the Warm Up will be active. See Warm
Up mode section for details.
Data Display
• When Warm Up mode is completed, the data display window will display the
default workout data of “calories, speed & level”. Press “Select” button to switch
the data displays to “watts, distance & RPM”.
• Time display will show the selected program time and count down.
• Pulse display:
– If there is no pulse input, the Pulse data display will show “ - - -“ and blink.
If there continues to be no pulse input, this console will maintain its current
resistance setting and not changing until the program ends or is changed.
– If there is a valid pulse, the Pulse display will show the actual pulse reading.
Adjustment
• Press “Level Up/Down” key during Rest HR segment to adjust the Rest HR
setting of the remaining program. The Pulse window will blink the Rest HR
setting and adjust. Until the adjustment is done, it then will resume to display
actual HR. Dot matrix window will update the Rest %Max HR profile
accordingly.
• Press “Level Up/Down” key during Work HR segment to adjust the Work HR
setting of the remaining program. The Pulse window will blink the Work HR
860 Er Owner’s Manual
27
860erOM
6/20/06
8:42 PM
Page 30
Workout Programs (continued) / Maintenance
setting and adjust. Until the adjustment is done, it then will resume to display
actual HR. Dot matrix window will update the Work %Max HR profile
accordingly.
Ending the Program
• When selected program time is up or Stop key is pressed, this program will end
and Cool down will be active. See Cool down section for details.
• There will be a beep sound to indicate the program ended.
Pause, Reset, Re-start or Switch a program
See Console Operating Tips section for details, page 13.
MAINTENANCE
CAUTION – FOR SAFE OPERATION
Always inspect hardware prior to any exercise session. Look for loose hardware, loose
pedals, loose handrails, loose cranks and frayed wires. Repair or replace any damaged or worn parts, tighten all loose hardware.
After workout, always wipe down your 860Er unit. Perspiration that continuously settles on frame, pads or casing may eventually cause rust or damage to the unit. Damage
resulting from lack of proper maintenance will not be covered under warranty. To clean
pads, use a mild soap and warm water. Dry with a clean towel.
If noises develop or malfunctions occur, contact your authorized Diamondback Fitness
dealer.
28
860 Er Owner’s Manual
860erOM
6/20/06
8:42 PM
Page 31
Domestic warranty Information
(Applies to all product sold and placed within the continental US,
Alaska, Hawaii, and Puerto Rico only)
Effective: June 2006
Diamondback warrants its 860Er to be free from defects in material and workmanship
under normal use in the home environments. Diamondback’s obligation under this
Warranty is limited to repair or replacement of any defective part without charge
through an authorized service agent to the original purchaser with the following parameters:
Who is covered:
The Warranty is extended to the individual or legal entity whose name appears on the
Warranty registration card filed with Diamondback and may not be transferred to any
other individual or legal entity.
To obtain service:
To obtain service you must contact your authorized Diamondback Fitness dealer. Your
dealer is also your authorized service agent. An authorized service agent must diagnose your unit in order to determine Warranty claims/issues.
Sales where the unit is delivered unassembled (in a carton) to the end user (e.g. mail
order or Internet sales) without a service contract purchased through the dealer voids
the Warranty.
Warranty Registration:
Warranty commitments are valid only with a completed Warranty card that is returned
within 15 days from the date of purchase and includes the product serial number.
Registration is available at www.diamondbackfitness.com.
Proof of purchase from Diamondback’s authorized dealer will be required if the
Warranty card is not registered prior to any consideration of Warranty claim.
WHAT IS COVERED
Home
Maximum Usage: 14 Hours per week
Frame:
Parts & Electronics:
Normal Wear Items:
Labor:
Lifetime limited Warranty. Covers defects in welds,
materials and workmanship.
3 years
90-day limited on foam grips, pedals, etc.
1 Year
860 Er Owner’s Manual
29
860erOM
6/20/06
8:42 PM
Page 32
Domestic warranty Information (continued)
Warranty voided if:
The Warranty does not apply to any failure of the product, or any parts of the product,
due to: assembly errors, alterations, modifications, misuse, abuse, accident, improper
maintenance, or if the serial number on the product has been removed, altered or
defaced. Assembly errors include but are not limited to:
Damaged wire harness.
Bolts used in the wrong location.
Parts & Service:
Contact the authorized Diamondback dealer where unit as originally purchased. If you
have moved, or that retailer is unavailable, use our dealer locator at
www.diamondbackfitness.com to help find another authorized dealer.
Diamondback is not responsible for arranging Warranty service and/or honoring
extended warranties provided by dealers.
Exclusions:
Warranty is void if the 860Er unit is placed in a commercial or light commercial environment, such as health club, school, or correctional facility.
Additional Rights:
This Warranty is expressly in lieu of all other warranties, and any implied warranties of
merchantability or fitness for a particular purpose created hereby, are limited to the
same duration as the express Warranty herein. Diamondback Fitness, Inc. shall not be
liable for any incidental or consequential damages. Some states do not allow the exclusion or limitations of implied warranties, incidental or consequential, so the above limitations and exclusions may not apply to you.
Retailers and wholesale outlets for Diamondback Fitness, Inc. products are not authorized to modify this Warranty in any way.
This Warranty gives the original owner specific legal rights. Other additional rights may
vary from state to state.
Diamondback Fitness, Inc.
300 Camarillo Ranch Road
Camarillo, CA 93012
Phone no. 800.776.7642
30
860 Er Owner’s Manual
860erOM
6/20/06
8:42 PM
Page 33
Warranty card
Important! • Important! • Important! • Important! • Important! • Important!
Warranty card must be completed and returned to Diamondback within 15 days of purchase. Failure to
comply may void manufacturer’s Warranty. Or, you may register your product at
www.diamondbackfitness.com.
Your Name:
Address:
City:
State:
Daytime phone No.:
Evening phone No.:
Zip:
Dealer Store Name: Address:
City:
State:
Model:
Serial No.:
Zip:
Purchase Date:
Environment Unit Placed:
❏ Home
❏ Light Institutional, i.e. Hotel, Business Center…
Mail completed form to:
Diamondback Fitness - Warranty Card
300 Camarillo Ranch Road
Camarillo, CA 93012
860 Er Owner’s Manual
31
860erOM
6/20/06
8:42 PM
Page 2
Please refer to www.diamondbackfitness.com for instructions in French.
Svp référez-vous www.diamondbackfitness.com pour instructions en français.
Diamondback Fitness, Inc.
300 Camarillo Ranch Road
Camarillo, CA 93012
T 800-776-7642
F 805-388-5890
Part No. 22-96-115