DSEControl®
DSEM870
PROGRAMMABLE DISPLAY FOR USE IN
VEHICLES AND OFF-HIGHWAY MACHINERY
OVERVIEW
DC SUPPLY
8 V DC to 32 V DC
CURRENT CONSUMPTION
OPERATING CURRENT
< 1000 mA at 12 V and 24 V without
external loads
< 1500 mA at 12 V and 24 V with Htr.
DISPLAY
800 px x 480 px
24 bit colour
Optically bonded
INPUTS/OUTPUTS (total)
4 inputs / 4 outputs
INPUTS
Configurable,
Digital inputs (positive / negative)
Analogue inputs (Voltage 0 V to 5 V, 0 V to
10 V, 0 V to 32 V, current 4 mA to 20 mA,
Ratiometric, Resistive, Frequency)
KEY FEATURES / SUMMARY
• Robust HMI/programmable display specifically designed for mobile applications
• Optically bonded 7” colour screen for harsh environments
• Powerful ARM Cortex A9 processor with 800 MHz clock speed
• 512 MB of DDR3 SDRAM and 2 GB of NAND mass storage
• 4 configurable inputs, digital and analogue capability
• 4 configurable digital outputs
• 2 independent CAN interfaces, J1939, CAN open and Raw CAN
• Ethernet interface for communication
• Flexible user programming via CODESYS 3.5 and QT
• IP67 protection/NEMA 6
• 2 camera inputs
ADDITIONAL HARDWARE
DSE PART
Deutsch connector A, 18 way complete with pins
Deutsch connector C, 18 way complete with pins
M870 connector harness
M870 panel gasket
Ethernet programming cable
M12 to USB cable
007-850
007-851
016-167
020-579
016-160
016-161
OUTPUTS
Configurable
Digital Output High-Sided/Low-Sided
INTERFACES
CAN 1.2
CAN Interfaces 2.0 A/B, ISO11898
50 kbits/s... 1 Mbit/s
CAN Open, SAE J1939 or Raw CAN
ETHERNET
10 Mbit/s / 100 Mbit/s, Duplex
USB
USB Host 2.0 (12 Mbit/s)
DIMENSIONS
272 mm x 165 mm x 81 mm (W x H x D)
10.7” x 6.5” x 3.2” ( W x H x D)
WEIGHT
< 1 kg
STORAGE TEMPERATURE RANGE
-40 ˚ C to +85 ˚ C
-40 ˚ F to +185 ˚ F
OPERATING TEMPERATURE RANGE
-40 ˚ C to +85 ˚ C
-40 ˚ F to +185 ˚ F
PROTECTION RATING
IP67/NEMA 6 (with mating connectors)
MOUNTING
8 x M5 bolts / RAM arm
RELATED MATERIALS
TITLEPART NO.
M870 Installation Instructions057-187
M870 Operator Manual057-246
DEEP SEA ELECTRONICS PLC UK
Highfield House, Hunmanby Industrial Estate, Hunmanby YO14 0PH
TELEPHONE +44 (0) 1723 890099 FACSIMILE +44 (0) 1723 893303
EMAIL sales@deepseaplc.com WEBSITE www.deepseaplc.com
DEEP SEA ELECTRONICS INC USA
3230 Williams Avenue, Rockford, IL 61101-2668 USA
TELEPHONE +1 (815) 316 8706 FACSIMILE +1 (815) 316 8708
EMAIL sales@deepseausa.com WEBSITE www.deepseausa.com
Deep Sea Electronics Plc maintains a policy of continuous development and reserves the right to change
the details shown on this data sheet without prior notice. The contents are intended for guidance only
Registered in England & Wales No.01319649
VAT No.316923457
055–199/10/17 (3)
DSEControl®
Technical Data
DSEM870
Supply
Connector A
Operating voltage
8 V DC to 32 V DC
Unit power supply maximum current consumption, full backlight (no external loads)
< 1000 mA at 12 V and 24 V
Unit power supply maximum current consumption, full backlight and heater (no external
loads)
< 1500 mA at 12 V and 24 V
Unit power supply current consumption after controlled shutdown has occurred due to
the ignition being turned off
< 5 mA at 24 V
Fusing
Pin 7
Connector A
Unit power supply external protection fuse rating
3A
Pin 7
High current outputs supply input external fuse protection rating (i.e. sum of output
currents from all outputs provided for by an individual supply to < external fuse rating in
total)
10 A
Pin 1
Housing
PC PBT alloy plastic resin
Dimensions
140 mm x 230 mm x 60 mm (W x H x D) / 10.8” x 6.3” x 3.15” ( W x H x D)
Weight
< 1 kg
Temperature
Operating temperature
-40 ˚ C to +85 ˚C / -40 ˚ F to +185 ˚ F
Storage temperature
-40 ˚ C to +85 ˚C / -40 ˚ F to +185 ˚ F
Protection Rating
IP67 (with mating connectors)
Display
Resolution, pixel
800 px x 480 px
Colour
24 bit
Format
7” diagonal
Mounting
Optically bonded
Illumination
LED (lifetime > 50,000 hrs)
Connectors
Connector A
18 pin TE connectivity DT1618SA-K004
Connector C
18 pin TE connectivity DT1618SC-K004
Ethernet
M12, D-coded 4 pole socket
USB
M12, B-coded 5 pole socket
Digital Inputs
Connector C
Digital inputs configured high or low
Pin 14, 15, 16, 17
High level voltage threshold
>6V
Low level voltage threshold
<2V
Analogue Voltage Inputs
Connector C
0 V to 5 V programmable voltage range
0 V to 5 V
0 V to 10 V programmable voltage range
0 V to 10 V
0 V to 32 V programmable voltage range
0 V to 32 V
Voltage measurement resolution
12 bits
Voltage measurement accuracy
± 1% FSD
Voltage measurement input resistance
≥ 30 kΩ
Voltage measurement sampling rate
500 Hz
Pin 14, 15, 16, 17
FSD = Full Scale Deflection
055–199/10/17 (3)
DSEControl®
DSEM870
Analogue Current Inputs
Connector C
Current measurement direction
Current sink only
Current measurement ranges
0 mA to 20 mA
Pin 14, 15, 16, 17
4 mA to 20 mA
Current measurement resolution
12 bits
Current measurement accuracy
± 1% FSD
Current measurement input sink resistance
100 Ω ± 1%
Current measurement sampling rate
500 Hz
FSD = Full Scale Deflection
Analogue Resistive Inputs
Connector C
Resistance measurement range
0 Ω to 3200 Ω
Resistance measurement source voltage
12 V maximum
Resistance measurement current
1 mA
Resistance measurement resolution
12 bits
Resistance measurement accuracy
± 1% FSD
Resistance measurement sampling rate
500 Hz
Pin 14, 15, 16, 17
FSD = Full Scale Deflection
Analogue Ratiometric Inputs
Connector C
Voltage ratiometric measurement voltage range
Pin 14, 15, 16, 17
Voltage ratiometric measurement Vref
Supply/Vref
Voltage ratiometric measurement
Ratio of input pin to supply
voltage
Voltage ratiometric measurement accuracy
± 1% FSD
FSD = Full Scale Deflection
Frequency Inputs
Connector C
Frequency range
5 Hz to 30 Hz
Resolution
100 Hz at max. freq
Accuracy
400 Hz at max. freq
Maximum space voltage
< 1.4 V
Minimum mark voltage
>2V
Digital Outputs High Side
Connector C
Switching current
2A
Digital output active high ‘ON’ state internal voltage drop at rated current
< 100 mV
Digital output active high ‘OFF’ state leakage current
< 10 µA at 24 V
Digital Outputs Low Side
Pin 2, 3, 4, 5
Connector C
Switching current
2A
Digital output active low ‘ON’ state maximum voltage at rated current
< 100 mV
Digital output active low ‘OFF’ state leakage current
< 5 µA at 24 V
Reference Voltage
Reference voltage output
Pin 14, 15, 16, 17
Pin 2, 3, 4, 5
Connector C
Programmable 5 V or 10 V,
500 mA accuracy ±5%
6
VRef GND Pin 18
Auxiliary Voltage
12 V auxiliary voltage
Connector C
max 100 mA
Pin 13
055–199/10/17 (3)
DSEControl®
DSEM870
RTC
Real time clock
Standard RTC, powered by
Super Cap, backup time ~800
hours
Camera
Connector A
Analogue video input (supported video standards: PAL & NTSC)
2
5, 6, 11, 12
CAN Interfaces
Connector A
Number of CAN ports
2
Supported protocols
J1939
Pin 2, 3, 8, 9, 14, 15
CAN open
Raw CAN
Supported programmable baud rates
50 kbit/s, 125 kbit/s, 250
kbit/s, 500 kbit/s, 800 Mbit/s,
1 Mbit/s
Ethernet Interface
M12, 4 pole
Number of Ethernet ports
1
Supported data rates
10/100 Mbit/s
D-coded 4 pole socket
Supported protocols
Modbus TCP
CODESYS 3.5
USB Interface
M12, 5 pole
Number of USB host ports
1
Supported USB version
2
B-coded, 5 pole socket
Speeds supported
Full speed (12 Mbit/s)
Device class supported
08 (Mass Storage)
Supported filing system
FAT32
Processor
Technexion Freescale iMX6-SOLO Microcontroller
ARM A9
800 MHz
Memory
Flash
4 GB
RAM
512 MB
LED Status
Colour
Description
Operation
State
None
Device not powered
N/A
Off
Green
Unit powered up, application program loaded but not running
Static
Application stopped
Unit powered up, application program loaded and running
1 Hz flash
Application running
Unit powered up, but no application program loaded
5 Hz flash
No application
Bootloader functioning normally, firmware present
Static
Bootloader mode
Firmware is at start-up
Static
Firmware start-up
Unit stopped due to a serious fault
Static
Application exception
Bootloader is decrypting the downloaded image
1 Hz flash
Decrypting image
Bootloader is reading an image from the USB
5 Hz flash
Reading image from
USB
Fatal system/hardware fault - LEd may be driven directly by
microcontroller error pin or firmware is in a fault condition
Static
Fatal error
1 Hz flash
Faulty application
running
Amber
Red
Unit running with a fault, see CODESYS error flags
or web tool.
055–199/10/17 (3)
DSEControl®
DSEM870
Environmental and Testing
CE marking
Electromagnetic compatibility (EMC) noise immunity
Electromagnetic compatibility (EMC) emission standard
EN 13309
EN 13766
E11 marking
Emission standard noise immunity with 100 V/m
UN/ECE-R10
Electrical tests
Pulse 1, severity level: IV; function state C
Pulse 2a, severity level: IV; function state B
Pulse 2b, severity level: IV; function state C
Pulse 3a, severity level: IV; function state A
Pulse 3b, severity level: IV; function state A
Pulse 4, severity level: IV; function state B
Pulse 5a, severity level: III; function state C
ISO 7637-2
Climatic tests
Damp heat, cyclic upper temperature 55 ˚C, number
Damp heat, steady state test temperature 40 ˚C / 93% RH
Test duration: 21 days
Salt spray test severity level 3 (vehicle)
EN 60068-2-30
EN 60068-2-78
Test VII; vibration, random mounting location: vehicle body
Vibration, sinusoidal
2000 Hz: 0.73 mm / 10g: 10 cycles/axis
Bumps 30 g / 6 ms; 24,000 shocks
ISO 16750-3
EN 60068-2-6
Mechanical tests
EN 60068-2-53
ISO 16750-3
055–199/10/17 (3)
DSEControl®
DSEM870
PROGRAMMABLE DISPLAY FOR USE IN
VEHICLES AND OFF-HIGHWAY MACHINERY
Connector A
PIN
DESCRIPTION
PIN
DESCRIPTION
REF
1
EGU Supply GND
1
Output supply +VE
2
CAN1 GND
2
OUT H, L
QC001
3
CAN2 GND
3
OUT H, L
QC002
4
No connection
4
OUT H, L
QC003
5
Camera 1 GND
5
OUT H, L
QC004
6
Camera 2 GND
6
VREF +
7
ECU Supply +VE
7
Output supply GND
8
CAN1 H
8
No connection
9
CAN 2 H
9
No connection
10
No connection
10
No connection
11
Camera 1 signal
11
No connection
12
Camera 2 signal
12
Output supply GND
13
Ignnition +VE (15)
13
Aux 12 +VE Output
14
CAN1 L
14
DIN H, L, FREQ
IC001
15
CAN2 L
15
DIN H, L, FREQ
IC002
16
No connection
16
DIN H, L, FREQ
IC003
17
No connection
17
DIN H, L, FREQ
IC004
18
No connection
18
VREF GND
Ethernet
M12 ‘D’ coded - 4 pin female
Abbreviations
OUT PWM, H, L
OUT H
OUT H, L
AIN
DIN, H, L, FREQ
A GND
Connector C
USB Host
M12 ‘B’ coded - 5 pin female
Pin - 01
TX+
Pin -01
5V
Pin - 02
RC+
Pin - 02
Data+
Pin - 03
TX-
Pin - 03
Data-
Pin - 04
RC-
Pin - 04
0V
Pin - 05
Shield
Output can be configured as a PWM, PWMi, digital high-side or digital low-side
Output is digital high
Output can be configured as a digital high-side or digital low side
Input can be configured to accept signals from positive digital, negative digital, 0 V to 10 V, 4 mA to 20 mA, ratiometric or resistive
Input can be configured to accept signals from positive digital, negative digital or frequency
Ground connection for the analogue input channels
055–199/10/17 (3)
Download PDF
Similar pages