E5802B/E5833B/ E1802B/E1833B 5.8 GHz

Quick start guide
E5802B/E5833B/
E1802B/E1833B
5.8 GHz cordless
telephone with caller
ID/call waiting
Battery installation & charging
After installing the battery, you may be able to make or receive short calls. For
best performance, place the handset in the telephone base or charger to charge
for 16 hours before use.
You can keep the battery charged by returning the handset to the telephone
base or charger after use. When the battery is fully depleted, a recharge takes
about 12 hours. The average talk time on a fully charged battery is about five
hours, and the standby time is approximately six days. Actual battery life depends
on usage conditions and age of battery.
2
3
1. Insert the plug as indicated. Be sure to
securely insert the plug, making sure that
it matches the color-coded label inside the
battery compartment.
2. Place the battery and wires inside the compartment.
3. Slide the battery compartment cover up until
it clicks.
1
NOTE: Under normal conditions, the battery should last around one year. This may vary
depending on usage.
Caution: Use only the supplied rechargeable battery, replacement battery 2422 (SKU 23402, part
number 89-0047-00-00) or equivalent. To order a replacement battery, visit our
website at www.telephones.att.com or call 1 (800) 222-3111. In
Canada dial 1 (866) 288-4268.
Choose a central location close to a telephone jack and a power outlet not connected
to a wall switch. The telephone base can be placed on a flat surface or mounted on a
standard wall plate. For optimum range and better reception, place the telephone base
in a high and open location.
Avoid placing the telephone base too close to:
• Communication devices such as: personal computers, computer routers, television
sets, VCRs, wireless routers (wireless broadband, wi-fi, or 802.11) or other cordless
telephones.
• Excessive heat sources.
• Noise sources such as a window with traffic outside, motors, microwave ovens,
refrigerators, or fluorescent lighting.
• Excessive dust sources such as a workshop or garage.
• Excessive moisture.
• Extremely low temperature.
• Mechanical vibration or shock such as on top of the washing machine or work
bench.
Telephone base installation
1. Plug the small end of the larger
2. Plug the end of the telephone line
power adapter into the power jack at
the bottom of the telephone base.
cord into the telephone jack at the
bottom of the telephone base.
3. Route cords through
slots.
5. Plug the other end of the telephone line cord into a telephone jack.
4. Plug the large end of
the larger power adapter
into an electrical outlet
not controlled by a wall
switch.
Telephone line cord
DSL filter
(Optional for DSL users,
see number four in the
note section, below.)
6. You may be able to make or
receive short calls. For best performance, place the handset in
the telephone base or charger to
charge for at least 16 hours before
first use.
NOTES:
1. Use only the power adapter supplied with this product or equivalent.
To order a replacement power adapter, visit our website at www.telephones.att.com
or call 1 (800) 222-3111. In Canada dial 1 (866) 288-4268.
2. Be sure to use an electrical outlet not controlled by a wall switch.
3. This power adapter is intended to be correctly oriented in a vertical or floor mount position.
4. If you receive high speed internet through your telephone line (commonly referred to as DSL),
and you are experiencing interference during telephone conversations and/or your caller ID
features are not functioning properly, install a DSL filter to the telephone line between the telephone base and the telephone wall jack. Contact your DSL service provider for a DSL filter.
Quick reference guide
Cordless handset
CID/-VOLUME
While in a menu, press to scoll
down. When in idle mode, press
to display call summary entries.
While entering names or numbers, press to move the cursor to
the left. During a call, press CID
to decrease listening volume.
DIR
/VOLUME+
While in a menu, press to scoll up.
When in idle mode, press to display directory entries. While entering names, press to advance the
cursor. During a call, press DIR to
increase listening volume.
OFF/CLEAR
PHONE/FLASH
Press to make or answer a call.
During a call, press to receive
an incoming call if call waiting is
activated.
During a call, press to hang up.
While using menus, press to
cancel an operation, or exit the
menu.
CHAN/DELETE
When on a call, press CHAN/
DELETE to scan for a clearer channel when there is static or interference on the line. When in caller
ID mode, press to delete the displayed caller ID entry, or press
and hold to delete all caller ID
entries.
MENU/SEL/TRANSFER
Press to display menu. Press to
store a programming option. During
a call, press to transfer a call
between handsets.
MUTE
While on a call, press to mute
microphone. Press again to resume.
SPEAKER
Press to activate handset speakerphone. Press again to resume
normal handset use.
Feature menu
DIRECTORY
REDIAL/PAUSE
While in idle mode, press to display
last number called. While dialing or
entering numbers to the directory,
press to insert a four-second dialing pause.
Feature menu
Using menus
DIRECTORY
SPEED DIAL
RINGER
DATE/TIME
DIAL MODE
CLR VOICE MAIL
LANGUAGE
Press CID or DIR
menu items.
to scroll through
Press MENU/SEL to select or modify a
highlighted item.
Press OFF/CLEAR to cancel an operation,
or exit the menu display.
NOTE: For more information, please refer to the user's manual.
Quick reference guide
Telephone base
VOICEMAIL
Flashes when there is new voicemail
(requires voicemail service from your
local telephone company).
CHARGE/IN USE
• On when the cordless handset is properly positioned
to charge in the telephone base.
• Flashes when one of the handsets is in use.
• Flashes quickly while an incoming call is ringing.
HANDSET LOCATOR
Press to make handset(s) beep when
there is no handset on the telephone base.
NOTE: For more information, please refer to the user's manual.
www.telephones.att.com
© 2007 Advanced American Telephones. All rights reserved.
AT&T and the AT&T logo are trademarks of AT&T Knowledge Ventures,
licensed to Advanced American Telephones. Printed in China. Issue 5 AT&T 06/07.
96-006311-040-100