safety
GFCI / ELCI / EGFPD
safety products
Introduction
Coleman Cable, along with its subsidiary
Technology Research Corporation (TRC), has
an extensive line of electrical safety products
that ensures protection from dangerous
current leakage that can cause electrical
shock and possible electrocution. Our patented
technologies enable you to protect people,
property and equipment.
Coleman Cable’s Shock Shield® products are every day electrical safety devices
for use at home, the office, on construction sites or wherever people use portable
electrical equipment. These devices are required to be used throughout the USA
in accordance with the following nationally accepted regulations:
• NEC (2008) Article 590.6 Temporary Installations
• OSHA Standard for General Industry, 29 CFR, 1910 Subpart S
• OSHA Standard for Construction Industry, 29 CFR, 1926.404(b)
• UL 943
Shock Shield® products also meet Canadian Standard CSA CAN/CSA-C22.2
No. 144.1-06
Need protection at higher voltage and higher current? Coleman Cable’s HD-PRO™
series provides heavy duty ground fault protection for high current, rugged
environments. The HD-PRO™ series of electrical protection products have been
designed with TRC’s patented GFCI/ELCI technology and are available with ratings
from 120V/30A single phase up to 600V/100A three phase and engineered to trip
within 25 milliseconds, after ground fault detection, at trip levels that range from
6mA to 50mA. The HD-PRO™ Series employs contactors that are fully rated for
motor switching demands and designed to protect expensive high current, high
voltage equipment at the point of use while offering substantial shock protection
for individuals as well.
Unprotected cables are at risk for damage from vehicles and pedestrian traffic. They
also pose a tripping and entanglement hazard for personnel. All can result in costly
repairs and downtime. Coleman Cable’s cable management system, Yellow Jacket®,
provides a variety of cable protection solutions to meet your specific needs from
light weight loads to heavy loads up to 21,000 pounds. These solutions support
all of your on the ground requirements.
Based on data from the National Fire Protection Association, electrical failures were
factors in over 13% of home fires in 2009 in the US. The special braided shield
on Coleman Cable’s Fire Shield® products allows the plug-mounted electronics
to continuously monitor for insulation breakdown or broken/frayed conductors.
Standard electrical cords have no means of monitoring for leakage currents and
cannot shut off power before these currents can arc and start a fire. Fire Shield®
technology is available on extension cords and a variety of surge strips. Protect
your family and equipment from the damaging effects of power surges and spikes.
CCI — Power with the best™
2
safety products
Table of Contents
Table of Contents
Ground Fault Circuit Interrupters (GFCI)
Shock Shield® Single Outlet Adapter ............................................................... 4
Shock Shield® User Attachables ............................................................... 5 - 10
Shock Shield® Right Angle Cord Sets ............................................................ 11
Shock Shield® In-line Cord Sets.............................................................. 12 - 14
Shock Shield® Auto Reset In-Line Cord Sets................................................. 15
Shock Shield® Tri-Cords........................................................................... 16 - 17
Shock Shield® Quad Boxes ..................................................................... 18 - 19
Portable GFCI Receptacles .............................................................................20
X-Treme Box™ Portable Temporary Power Distribution Units ............... 21 - 22
Extension Cords.............................................................................................. 23
Adapters .......................................................................................................... 23
Shock Shield® Outlet Tester ............................................................................ 24
Electra Check® Digital Monitor ....................................................................... 25
Shock Shield® GFCI/ELCI Panel Mounts................................................ 26 - 27
High Power Equipment
GFCI, ELCI, Combination Devices (GFCI/ELCI)
Shock Shield® High Power GFCIs .................................................................. 28
HD-PRO™ Heavy Duty ELCI 30A .................................................................. 29
HD-PRO™ Heavy Duty ELCI 60A .................................................................. 30
Ground Fault Protective Devices (EGFPD)
and GFCI/ELCI Adjustables
HD-PRO™ GFCI/ELCI Adjustables 6.10.30 .......................................... 31 - 32
HD-PRO™ EGFPD Adjustables .................................................................... 33
Wiring Instructions for High Power GFCI/ELCIs ............................................ 34
Specialty Products
Heavy Duty Three Wire Extension Cord Set ................................................... 35
Fire Shield® Surge Strips................................................................................. 36
Cable Protection Systems
Yellow Jacket® & Black Jacket™ .................................................................... 37
Definitions .................................................................................................... 38
OSHA Specifications ................................................................................. 39
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
3
safety products
Single Outlet GFCI Adapters
Single Outlet GFCI Adapters
Provides GFCI and single mode surge protection (listed UL 1449) with
any appliance or tool used indoors. Its small size (less than 3” high and
2” wide) makes it perfect for the toolbox and offers portable protection
for institutional and residential applications:
Cost effective
Perfect for Power Tools, Saws, Drills, Extension Cords, Lighting
To prevent unmonitored equipment startup, manual reset is required
after GFCI trip and power outage. Available in yellow with button boots
or white. Provides compliance with National Electric Code (NEC 2008)
Article 590.6 for “Temporary Installations.”
FEATURES
14650 006-6 (White)
14650 013-6 (Yellow)
Volts/Amps: 120V/15A
NEMA 5-15 P & R
Trip Level: 4 - 6 mA
MOV - 314 joules
14650 013-6
TECHNICAL DATA
Grounded Neutral
Trip response time for ground fault
and grounded neutral trip
Voltage surge withstand
4 Ohms typical
less than 25mS
3kv ringwave test and
4kv/2kA surge immunity test
Radio frequency noise susceptibility operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
50 / 60 Hz
Frequency
3,000 operations minimum
Endurance
six times rated current
Overload Current
-35˚C to 66˚C
Operating temperature range
5% maximum trip level variation
Effect of 10 Amp turn DC Shock
on ground fault trip
1500 VRMS - 1 Min.
Insulation voltage
mechanical indicator
Power On indication
4
safety products
GFCI & ELCI
User Attachable Plugs
GFCI & ELCI User Attachable Plugs
The user attachable plug is ideal for existing equipment without GFCI
protection, the male connector can be removed and the GFCI plug
easily attached to equipment’s cord. Applications include:
Pressure Washers
Floor Cleaners
Power Tools
Boat Lifts
Drain Snakes
Industrial Appliances
Pumps
Extension Cords
Rainproof rated, UL listed for outdoor use. To prevent unmonitored
equipment startup, manual reset is required after GFCI trip and power
outage. Allows compliance with National Electric Code (NEC 2008)
Article 590.6 for “Temporary Installations” and OSHA regulation.
Available with yellow or black case.
FEATURES
14880 002-6 GFCI
Volts/Amps: 120V/15A
Accepts 18 - 12 AWG(SJT)
NEMA 5 - 15 P, Yellow
Trip Level: 4 - 6 mA
24230 101-3 ELCI
Volts/Amps: 120V/15A
Accepts 18 - 12 AWG (SJT)
NEMA 5-15 P, Black
Trip Level: 10 mA
14880 232-6 GFCI
Volts/Amps: 120V/15A
Accepts 18 - 12 AWG (SJT)
NEMA 5 - 15 P, Black
Trip Level: 4 - 6 mA
54880 004-6 GFCI
Volts/Amps: 120V/20A
Accepts 18 - 12 AWG (SJT)
NEMA 5 - 20 P, Black
Trip Level: 4 - 6 mA
14880 002-6
1.68
2.05
C
US
TECHNICAL DATA*
Grounded Neutral
Trip response time for ground fault
and grounded neutral trip
Voltage surge withstand
4 Ohms typical
less than 25mS
3.70
3kv ringwave test and
4kv/2kA surge immunity test
Radio frequency noise susceptibility operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
50 / 60 Hz
Frequency
3,000 operations minimum
Endurance
six times rated current
Overload Current
-35˚C to 66˚C
Operating temperature range
5% maximum trip level variation
Effect of 10 Amp turn DC Shock
on ground fault trip
1500 VRMS - 1 Min.
Insulation voltage
mechanical indicator
Power On indication
* Applies to 14880-002 and 54880-004
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
5
safety products
Auto Reset GFCI
User Attachable Plug
Auto Reset GFCI User Attachable Plug
The user attachable GFCI is ideal for existing equipment without GFCI
protection. The male connector can be removed and the GFCI easily
attached to the equipment’s cord. Applications include:
Pressure Washers
Floor Cleaners
Power Tools
Boat Lifts
Drain Snakes
Industrial Appliances
Pumps
Vending Machines
Rainproof rated, UL listed for outdoor use. Manual reset is required
after GFCI trip and does not have to be reset with loss of power. Allows
compliance with National Electric Code (NEC 2008) Article 590.6 for
“Temporary Wiring” and OSHA regulation. Available in black only.
FEATURES
35190 001-6
Volts/Amps: 120V/15A
Accepts 18 - 12 AWG (SJT, SJTW)
NEMA 5 - 15 P
Trip Level: 4 - 6 mA
TECHNICAL DATA
Trip response time for ground fault
and grounded neutral trip
Voltage surge withstand
Radio frequency noise susceptibility
35190 001-6
6
Frequency
Endurance
Overload Current
Operating temperature range
Insulation voltage
Power On indication
less than 25mS
3kv ringwave test and
4kv/2kA surge immunity test
operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
60 Hz
3,000 operations minimum
six times rated current
-35˚C to 66˚C
1500 VRMS - 1 Min.
lighted indicator
safety products
GFCI In-Line User Attachables
GFCI In-Line User Attachables
The in-line user attachable is ideal for existing equipment without GFCI
protection, and can be easily attached by connecting the GFCI in
series with the supply cable 9 to 10 inches from the plug end to provide
GFCI protection. Applications include:
Pressure Washers
Floor Cleaners
Power Tools
Boat Lifts
Drain Snakes
Industrial Appliances
Pumps
Extension Cords
Rainproof rated, UL listed for outdoor use. To prevent unmonitored
equipment startup, manual reset is required after GFCI trip and power
outage. Allows compliance with National Electric Code (NEC 2008)
Article 590.6 for “Temporary Installations” and OSHA regulation.
Available with yellow or black case.
FEATURES
25000 016-6
Volts/Amps: 120V/20A and 240V/20A
Accepts 18 - 12 AWG (SJT)
Trip Level: 4 - 6 mA
25230 001-6
Volts/Amps: 120V/20A
Accepts 18 - 12 AWG (SJT)
Trip Level: 4 - 6 mA
TECHNICAL DATA
Grounded Neutral
Trip response time for ground fault
and grounded neutral trip
Voltage surge withstand
Radio frequency noise susceptibility
Frequency
Endurance
Overload Current
Operating temperature range
Effect of 10 Amp turn DC Shock
on ground fault trip
Insulation voltage
Power On indication
4 Ohms typical
less than 25mS
3kv ringwave test and
4kv/2kA surge immunity test
operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
50 / 60 Hz
3,000 operations minimum
six times rated current
-35˚C to 66˚C
5% maximum trip level variation
25000 016-6
6.40
2.00
1.86
1500 VRMS - 1 Min.
lighted indicator
COVER REMOVED
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
7
safety products
GFCI In-Line User Attachables
GFCI In-Line User Attachables
The in-line user attachable is ideal for existing equipment without GFCI
protection, and can be easily attached by connecting the GFCI in
series with the supply cable 9 to 10 inches from the plug end to provide
GFCI protection. Applications include:
Pressure Washers
Floor Cleaners
Power Tools
Boat Lifts
Drain Snakes
Industrial Appliances
Pumps
Extension Cords
Rainproof rated, UL listed for outdoor use. These units require manual
reset after all fault conditions or interruption of the power supply. Allows
compliance with NEC 2008 Article 590.6,“Temporary Installations”and
OSHA regulation. Available with yellow or black case.
FEATURES
30040 006-6
Volts/Amps: 120V/20A
Accepts 16 - 12 AWG (ST)
Trip Level: 4 - 6 mA
30050 003-3
Volts/Amps: 240V/20A
Accepts 16 - 12 AWG (ST)
Trip Level: 4 - 6 mA
TECHNICAL DATA
30040 006-6
Grounded Neutral
Trip response time for ground fault
and grounded neutral trip
Voltage surge withstand
Radio frequency noise susceptibility
Frequency
Endurance
Overload Current
Operating temperature range
Effect of 10 Amp turn DC Shock
on ground fault trip
Insulation voltage
Power On indication
8
4 Ohms typical
less than 25mS
3kv ringwave test and
4kv/2kA surge immunity test
operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
50 / 60 Hz
3,000 operations minimum
six times rated current
-35˚C to 66˚C
5% maximum trip level variation
1500 VRMS - 1 Min.
mechanical indicator
safety products
ELCI In-Line User Attachables
ELCI In-Line User Attachables
Dual user attachable configurations for OEM connection of cable. Units
are dual voltage rated. Operation and trip times equal or exceed that of
the GFCI’s. Provides equipment protection for office equipment.
Applications include:
Copiers
Printers
Scanners
Film Processors
Image Setters
Appliances
To prevent unmonitored equipment startup, manual reset is required
after ELCI trip. Does not require reset following disruption of
primary power.
FEATURES
26140 010-6
Volts/Amps: 120V/20A & 240V/16A
Accepts 18 - 12 AWG (SJT)
Trip Level: 30 mA
25040 101-3
Volts/Amps: 120V/20A & 240V/16A
Accepts 18 - 12 AWG (SJT)
Trip Level: 10 mA
TECHNICAL DATA
Trip response time for ground fault
Voltage surge withstand
Radio frequency noise susceptibility
Frequency
Endurance
Overload Current
Operating temperature range
Insulation voltage (Hi-Pot)
Power On indication
less than 25mS
3kv ringwave test and
4kv/2kA surge immunity test
operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
50 / 60 Hz
5,000 operations minimum
six times rated current
10˚C to 60˚C
1500 VRMS - 1 Min.
lighted indicator
25040 101-3
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
9
safety products
PRCD In-Line User Attachables
PRCD In-Line User Attachables
CE Certified Portable Residual Current Device (PRCD); EU Directives
89/336/EEC – Electromagnetic Compatibility Directive, 72/23/EEC –
LowVoltage Equipment Directive & IEC 61540 – International standard
for PRCD’s. Available 110V – 230V, 6mA, 10mA & 30mA trip levels.
Applications include:
Pressure Washers
Floor Cleaners
Power Tools
Boat Lifts
Drain Snakes
Industrial Appliances
Pumps
Extension Cords
To prevent unmonitored equipment startup, manual reset is required
after PRCD trip and power outage.
FEATURES
57010 501-6
Volts/Amps: 230V/16A
Accepts 1.5 - 2.5mm2 conductor/
7.8-16.2mm dia. Cord Sets
Trip Level: 10 mA max.
CE Compliant
57020 501-6
Volts/Amps: 230V/16A
Accepts 1.5 - 2.5mm2 conductor/
7.8-16.2mm dia. Cord Sets
Trip Level: 30 mA max.
CE Compliant
57030 501-6
Volts/Amps 110/127V, 25A
Accepts 1.5 - 2.5mm2 conductor/
7.8-16.2mm dia. Cord Sets
Trip Level: 6 mA max.
CE Compliant
TECHNICAL DATA
57010 501-6
Response Time
40mS max at 5(I n)
Contacts
Normally Open (Manual Reset)
Contacts open with loss of power
LINE SIDE
2.10
(53.3)
1.34
(34.0)
Environmental Rating
IP-55
Frequency
50/60Hz
Voltage Surge Withstand
4KV
Radio Frequency Noise Susceptibility 160KHz-300MHz, per IEC61543
8.41
(213.6)
6.90
(175.3)
STRAIN RELIEF GROMMET
TYPICAL BOTH ENDS
LOAD SIDE
10
ACCEPTS 12AWG,14AWG, & 16AWG CABLE SIZES
2.10
(53.3)
Endurance
3,500 operations minimum
Overload Current
Four times rated current
Operating Temperature Range
-5ºC to +40ºC
Insulation Voltage
2,000V
Power On Indication
Mechanical indicator
safety products
GFCI Right Angle Cord Sets
GFCI Right Angle Cord Sets
Ideal for use by contractors and industrial maintenance personnel
working with extension cords or portable tools. Provides compliance
with National Electric Code (NEC 2008) Article 590.6 for “Temporary
Installations.” Applications include:
High Pressure Sprayer Washers Power Tools
Drain Snakes
Pumps
Construction Sites
Industrial Appliances
Rainproof rated, UL listed for outdoor use. Standard lengths: 9”, 6’, 25’,
50’.
Custom cable gauges, lengths and terminations available by special
order. To prevent unmonitored equipment startup, manual reset is
required after GFCI trip and power outage. Available with yellow or
black case.
FEATURES
14880 001-6 (9”)
14880 012-6 (9”)
14880 024-3 (6’)
14880 013-3 (6’)
14880 074-2 (25’)
14880 018-3 (25’)
14880 122-1 (50’)
Volts/Amps: 120V/15A
Cord Gauge: 14/3 AWG
NEMA 5-15P & R
Trip Level: 4 - 6 mA
14880 029-1 (50’)
Volts/Amps: 120V/15A
Cord Gauge: 12/3 AWG
NEMA 5-15P & R
Trip Level: 4 - 6 mA
14880 013-3
TECHNICAL DATA
Grounded Neutral
Trip response time for ground fault
and grounded neutral trip
Voltage surge withstand
4 Ohms typical
less than 25mS
3kv ringwave test and
4kv/2kA surge immunity test
Radio frequency noise susceptibility operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
50 / 60 Hz
Frequency
3,000 operations minimum
Endurance
six times rated current
Overload Current
-35˚C to 66˚C
Operating temperature range
5% maximum trip level variation
Effect of 10 Amp turn DC Shock
on ground fault trip
1500 VRMS - 1 Min.
Insulation voltage
mechanical indicator
Power On indication
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
11
safety products
GFCI In-Line Cord Sets
GFCI In-Line Cord Sets
Excellent for industrial plant maintenance, equipment service and
construction site applications. Provides compliance with National
Electric Code (NEC 2008) Article 590.6 for “Temporary Installations.”
Applications include:
High Pressure Sprayer Washers
Drain Snakes
Construction Sites
Construction Site Power Tools
Pumps
Industrial Appliances
Rainproof rated, UL listed for outdoor use. Custom cable gauges,
lengths and terminations available by special order. To prevent
unmonitored equipment startup, manual reset is required after GFCI
trip and power outage.
FEATURES
25080 011-6 (2’)
25090 001-6 (2’)
26000 011-6 (2’)
25080 016-3 (6’)
25090 006-3 (6’)
26000 016-3 (6’)
25080 025-2 (25’)
Volts /Amps: 120V/20A
Cord Gauge: 12/3 AWG
NEMA 5-20 P&R,
Black
Trip Level: 4-6 mA
25090 025-2 (25’)
Volts /Amps: 240V/15A
Cord Gauge: 14/3 AWG
NEMA 6-15 P&R,
Black
Trip Level: 4-6 mA
26000 125-2 (25’)
Volts /Amps: 240V/20A
Cord Gauge: 12/3 AWG
NEMA 6-20 P&R,
Black
Trip Level: 4-6 mA
26020 002-6 (2’)
*26020 121-6 (2’)
26020 007-3 (6’)
26020 124-2 (25’)
26020 050-1 (50’)
26020 099-1 (100’)
Volts /Amps: 120V/15A
Cord Gauge: 14/3 AWG
NEMA 5-15 P&R, Black
Trip Level: 4-6 mA
*Lighted receptacle
26020 011-6 (2’)
*26020 115-6 (2’)
26020 016-3 (6’)
26020 125-2 (25’)
26020 150-1 (50’)
Volts /Amps: 120V/15A
Cord Gauge: 12/3 AWG
NEMA 5-15 P&R, Black
Trip Level: 4-6 mA
*Lighted receptacle
TECHNICAL DATA
25080 011-6
Grounded Neutral
Trip response time for ground fault
and grounded neutral trip
Voltage surge withstand
4 Ohms typical
less than 25mS
3kv ringwave test and
4kv/2kA surge immunity test
Radio frequency noise susceptibility operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
50 / 60 Hz
Frequency
3,000 operations minimum
Endurance
six times rated current
Overload Current
-35˚C to 66˚C
Operating temperature range
5% maximum trip level variation
Effect of 10 Amp turn DC Shock
on ground fault trip
1500 VRMS - 1 Min.
Insulation voltage
lighted indicator
Power On indication
12
safety products
GFCI In-Line Cord Sets
GFCI In-Line Cord Sets
Designed for rugged duty. Molded from high impact polymer with
booted reset and test buttons. At home in hostile environments such as
industrial, construction, maintenance and commercial work sites.
Provides compliance with National Electric Code (NEC 2008) Article
590.6 for “Temporary Installations.” Applications include:
High Pressure Sprayer Washers Power Tools
Drain Snakes
Pumps
Construction Sites
Industrial Appliances
Rainproof rated, UL listed for outdoor use. Standard lengths: 2’, 6’,
and 25’ with corresponding locking connectors. Custom cable gauges,
lengths and terminations available by special order. To prevent
unmonitored equipment startup, manual reset is required after GFCI
trip and power outage.
FEATURES
44700 004-3 (2’)
44720 012-3 (3’)
44700 005-2 (6’)
44720 013-2 (6’)
44700 006-1 (25’)
Volts/Amps: 120V/30A
Cord Gauge: 10/3 AWG
NEMA L5-30P & R
Trip Level: 4 - 6 mA
44720 020-1 (25’)
Volts/Amps: 240V/30A
Cord Gauge: 10/3 AWG
NEMA L6-30P & R
Trip Level: 4 - 6 mA
TECHNICAL DATA*
Grounded Neutral
Trip response time for ground fault
and grounded neutral trip
Voltage surge withstand
4 Ohms typical
less than 25mS
44700 004-3
3kv ringwave test and
4kv/2kA surge immunity test
Radio frequency noise susceptibility operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
50 / 60 Hz
Frequency
3,000 operations minimum
Endurance
six times rated current
Overload Current
-35˚C to 66˚C
Operating temperature range
5% maximum trip level variation
Effect of 10 Amp turn DC Shock
on ground fault trip
1500 VRMS - 1 Min.
Insulation voltage
mechanical indicator, red stripe on reset
Power On indication
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
13
safety products
GFCI In-Line Cord Sets with
Molded Locking Connectors
GFCI In-Line Cord Sets with Molded
Locking Connectors
Excellent for industrial plant maintenance, equipment service and
construction site applications. Provides compliance with National
Electric Code (NEC 2008) Article 590.6 for “Temporary Installations.”
Applications include:
High Pressure Sprayer Washers
Drain Snakes
Construction Sites
Construction Site Power Tools
Pumps
Industrial Appliances
Rainproof rated, UL listed for outdoor use. Standard Lengths: 2’, 6’.
Custom cable gauges, lengths and terminations available by special
order. To prevent unmonitored equipment startup, manual reset is
required after GFCI trip and power outage.
FEATURES
26020 097-6 (2’)
Volts /Amps: 120V/15A
Cord Gauge: 14/3 AWG
NEMA L5 - 15 P & R
Trip Level: 4-6 mA
25080 136-6 (2’)
25080 137-3 (6’)
Volts /Amps: 120V/20A
Cord Gauge: 12/3 AWG
NEMA L5 - 20 P & R
Trip Level: 4-6 mA
TECHNICAL DATA
Grounded Neutral
Trip response time for ground fault
and grounded neutral trip
Voltage surge withstand
3kv ringwave test and
4kv/2kA surge immunity test
Radio frequency noise susceptibility operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
50 / 60 Hz
Frequency
3,000 operations minimum
Endurance
six times rated current
Overload Current
-35˚C to 66˚C
Operating temperature range
5% maximum trip level variation
Effect of 10 Amp turn DC Shock
on ground fault trip
1500 VRMS - 1 Min.
Insulation voltage
lighted indicator
Power On indication
26020 097-6
2.98
1.89
14
4 Ohms typical
less than 25mS
5.00
2.00
2.99
safety products
GFCI In-Line Cord Sets
with Auto Reset
GFCI In-Line Cord Sets with Auto Reset
The in line GFCI cord set is ideal for existing equipment without
GFCI protection. Applications include:
Drain Snakes
Refrigeration
Spas
Floor Cleaners
Pumps
Signs
Vending Machines
Rainproof rated, UL listed for outdoor use. Manual reset is required
after GFCI trip and does not have to be reset with loss of power. Allows
compliance with National Electric Code (NEC 2008) Article 590.6 for
“Temporary Wiring” and OSHA regulation. Available in black only.
FEATURES
35400 501-6 (2’)
Volts/Amps: 120V/15A
Cord Gauge: 14/3 AWG.
NEMA 5-15P & R
Trip Level: 4 - 6 mA
35450 501-6 (2')
Volts /Amps: 120V/20A
Cord Gauge: 12/3 AWG
NEMA 5 - 20 P & R
Trip Level: 4-6 mA
C
UL
US LISTED
TECHNICAL DATA
Trip response time for ground fault
and grounded neutral trip
Voltage surge withstand
(MOV Protection)
Radio frequency noise susceptibility
Frequency
Endurance
Overload Current
Operating temperature range
Insulation voltage (Hi-Pot)
Fault indication
less than 25mS
3kv ringwave test and
4kv/2kA surge immunity test
operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
60 Hz
3,000 operations minimum
six times rated current
-35˚C to 66˚C
1500 VRMS - 1 Min.
lighted indicator
35400 501-6
35400 501-6
35450 501-6
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
15
safety products
GFCI Plug Protected Tri-Cords
GFCI Plug Protected Tri-Cords
Heavy duty molded T-head with three receptacles. The GFCI is an
integral part of male plug. Provides protection for the extra heavy duty
cord and three attached tools. 12 gauge cord is ideal for outdoor rugged construction type environments. Applications include:
Construction Sites
Portable Electric Power Tools
Saws and Drills
Multiple Tools Use
Standard length: 2’, 6’, 25’, 50’, 99'. To prevent unmonitored equipment
startup, manual reset is required after GFCI trip and power outage.
Provides compliance with National Electric Code (NEC 2008) Article
590.6 for “Temporary Installations.”
FEATURES
14880 023-6 (2’)
*14880 226-6 (2’)
14880 004-6 (6’)
14880 118-2 (25’)
14880 119-1 (50’)
14880 120-1 (99’)
Volts/Amps: 120V/15A
Cord Gauge: 12/3 AWG
NEMA 5-15P & (3)5-15R
Trip Level: 4 - 6 mA
*Lighted receptacle
14880 004-6
14880 228-6 (25’) CCI 02837
14880 229-6 (50’) CCI 02838
14880 230-4 (100’) CCI 02839
Cord Gauge: 12/3 AWG, SJEOW
TECHNICAL DATA
Grounded Neutral
Trip response time for ground fault
and grounded neutral trip
Voltage surge withstand
4 Ohms typical
less than 25mS
3kv ringwave test and
4kv/2kA surge immunity test
Radio frequency noise susceptibility operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
50 / 60 Hz
Frequency
3,000 operations minimum
Endurance
six times rated current
Overload Current
-35˚C to 66˚C
Operating temperature range
5% maximum trip level variation
Effect of 10 Amp turn DC Shock
on ground fault trip
1500 VRMS - 1 Min.
Insulation voltage
mechanical indicator
Power On indication
16
safety products
In-Line GFCI Protected Tri-Cords
In-Line GFCI Protected Tri-Cords
Heavy duty molded T-head with three receptacles. Provides protection
for the extra heavy duty cord and three attached tools. 12 gauge cord is
ideal for outdoor - rugged construction type environments.
Applications include:
Construction Sites
Portable Electric Power Tools
Saws and Drills
Multiple Tools Use
Standard lengths 2’, 25’ and 50’. To prevent unmonitored equipment
startup, manual reset is required after GFCI trip and power outage.
Provides compliance with National Electric Code (NEC 2008) Article
590.6 for “Temporary Installations.”
FEATURES
26020 008-6 (2’)
*26020 146-6 (2’)
26020 147-2 (25’)
26020 148-1 (50’)
Volts/Amps: 120V/15A
Cord Gauge: 12/3 AWG
NEMA 5-15P & (3)5-15R
Trip Level: 4 - 6 mA
*Lighted receptacle
30040 008-6 (2.5’) CCI 02851
Volts/Amps: 120V/15A
Cord Gauge: 12/3 AWG, SEOW
NEMA 5-15P & (3)5-15R
Trip Level: 4 - 6 mA
Lighted receptacle
TECHNICAL DATA
Grounded Neutral
Trip response time for ground fault
and grounded neutral trip
Voltage surge withstand
4 Ohms typical
less than 25mS
3kv ringwave test and
4kv/2kA surge immunity test
Radio frequency noise susceptibility operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
50 / 60 Hz
Frequency
3,000 operations minimum
Endurance
six times rated current
Overload Current
-35˚C to 66˚C
Operating temperature range
5% maximum trip level variation
Effect of 10 Amp turn DC Shock
on ground fault trip
1500 VRMS - 1 Min.
Insulation voltage
lighted indicator
Power On indication
26020 008-6
30040 008-6
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
17
safety products
GFCI Plug Protected Quad Boxes
GFCI Plug Protected Quad Boxes
Enclosed in heavy impact resistant polymer case. Spring loaded covers
protect each pair of receptacles. “Circuit Breaker” built into box for
convenient reset. The GFCI is an integral part of the male connector.
Provides protection to the entire cord as well as tools attached. Built to
withstand outdoor/rugged-type construction. Applications include:
Drills
Lathes
Multiple tools
Saws
Lighting
Construction Sites
Standard lengths: 2’, 6’, 25’, 50’, 99’. To prevent unmonitored
equipment startup, manual reset is required after GFCI trip and power
outage. Complies with National Electric Code (NEC 2008) Article 590.6
for “Temporary Installations.”
FEATURES
14880 402-3 (2’)
14880 003-3 (6’)
14880 425-2 (25’)
14880 450-1 (50’)
14880 003-3
14880 121-1 (99’)
Volts/Amps: 120V/15A
Cord Gauge: 12/3 AWG
NEMA 5-15P & (4)5-15R
Trip Level: 4 - 6 mA
TECHNICAL DATA
Grounded Neutral
Trip response time for ground fault
and grounded neutral trip
Voltage surge withstand
4 Ohms typical
less than 25mS
3kv ringwave test and
4kv/2kA surge immunity test
Radio frequency noise susceptibility operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
50 / 60 Hz
Frequency
3,000 operations minimum
Endurance
six times rated current
Overload Current
-35˚C to 66˚C
Operating temperature range
5% maximum trip level variation
Effect of 10 Amp turn DC Shock
on ground fault trip
1500 VRMS - 1 Min.
Insulation voltage
mechanical indicator
Power On indication
18
safety products
In-Line GFCI Protected
Quad Boxes
In-Line GFCI Protected Quad Boxes
Box enclosed in heavy impact resistant polymer case. Spring loaded
covers protect each pair of receptacles. “Fast Breaker” built in for
convenient reset. GFCI with lighted indicator located at power end
provides protection to the cord and tools attached. Applications
include:
Drills
Saws
Multiple Tools Use
Lathes
Lighting
Construction Sites
To prevent unmonitored equipment startup, manual reset is required
after GFCI trip and power outage. Complies with National Electric
Code (NEC 2008) Article 590.6 for “Temporary Installations.”
FEATURES
26020 009-3 (6’)
25080 121-6 (2’)
26020 010-2 (25’)
25080 122-3 (6’)
26020 004-1 (50’)
Volts/Amps: 120V/15A
25080 123-2 (25’)
Volts/Amps: 120V/20A
Cord Gauge: 12/3 AWG
NEMA 5-20P & (4)5-20R
Trip Level: 4 - 6 mA
Cord Gauge: 12/3 AWG
NEMA 5-15P & (4)5-15R
Trip Level: 4 - 6 mA
26020 009-3
TECHNICAL DATA
Grounded Neutral
Trip response time for ground fault
and grounded neutral trip
Voltage surge withstand
4 Ohms typical
less than 25mS
3kv ringwave test and
4kv/2kA surge immunity test
Radio frequency noise susceptibility operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
50 / 60 Hz
Frequency
3,000 operations minimum
Endurance
six times rated current
Overload Current
-35˚C to 66˚C
Operating temperature range
5% maximum trip level variation
Effect of 10 Amp turn DC Shock
on ground fault trip
1500 VRMS - 1 Min.
Insulation voltage
lighted indicator
Power On indication
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
19
safety products
Cord-Connected Portable GFCI
with Duplex/Quad
GFCI Receptacles
Cord-Connected Portable GFCI with Duplex
GFCI Receptacles
High impact resin with a slant-roof design to prevent water entry.
Receptacles can accommodate large plugs. All models are Auto
Reset GFCIs. OSHA compliant. Applications include:
Construction Sites
Portable Electric Power Tools
Saws and Drills
For up to Two Tools
FEATURES
02822
02822 (6’)
Volts/Amps: 120V/15A
Cord Gauge: 12/3 SJTW
NEMA 5-15P & (2) 5-15R
02827 (25’)
02828 (50’)
Volts/Amps: 120V/15A
Cord Gauge: 14/3 SJEOW
NEMA 5-15P & (2) 5-15R
TECHNICAL DATA
Maximum operating voltage
120 Vac
Maximum operating current
15 Amp
Maximum operating wattage
1800 W
Temperature rating
-22˚C to +140˚C
Operating environment
Outdoor, if protected from water entry
Cord-Connected Portable GFCI with Quad
GFCI Receptacles
High impact resin with a slant-roof design to prevent water entry.
Receptacles can accommodate large plugs. All models are Auto
Reset GFCIs. OSHA compliant. Applications include:
Construction Sites
Portable Electric Power Tools
02821
Saws and Drills
For up to Two Tools
FEATURES
02816 (6’)
Volts/Amps: 120V/15A
Cord Gauge: 12/3 SJEOW
NEMA 5-15P & (4) 5-15R
02821 (6’)
Volts/Amps: 120V/15A
Cord Gauge: 12/3 SJEOW
NEMA L5-20P & (4) 5-20R
TECHNICAL DATA
20
Maximum operating voltage
120 Vac
Maximum operating current
15 Amp
Maximum operating wattage
1800 W
Temperature rating
-22˚C to +140˚C
Operating environment
Outdoor, if protected from water entry
safety products
CCI X-Treme Box
Temporary Power Distribution Unit
with GFCI Protection
CCI X-Treme Box™ Distribution Unit
with GFCI Protection
This rugged equipment is designed to safely distribute temporary
power in areas such as construction sites and other jobsite
environments. UL Listed for outdoor use and designed to stand up to
the toughest workplace conditions. The 125V/20A receptacles on the
unit are protected by individual GFCI’s with “Power On” indicators.
They also provide open neutral and reverse phasing protection. Each
unit has been carefully assembled to provide the ultimate in electrical
safety as well as meeting current OSHA requirements.
The units use a 50A California Standard power inlet that distributes
power to seven receptacles and a 50A California Standard pass-thru
power outlet for daisy-chaining additional units. In addition to the six
125V/20A receptacles, each unit has one additional non-GFCI NEMA
L6-30 turn-lock receptacle rated 250V/30A. Over current protection is
provided by a full complement of circuit breakers located under an
easy-access side panel.
01960
FEATURES
01960, 01962 (roll cage)
01970, 01972 (roll cage) – straight blades
1 – 125/250V/50A Input
1 – 125/250V/50A Pass-thru
6 – 125V/20A NEMA 5-20R GFCI
1 – 250V/30A NEMA L6-30R Non-GFCI
GFCI Trip Level: 4-6mA
ETL Listed to UL1640 and CAN/CSA C22.22 No. 14
Dimensions 14.5”W x 21”L x 11”H
01962
CCI Xtreme Box™ Distribution Unit Model 01962 Wiring Diagram
GFCI WH
Module
1
Receptacle
BK
2
WH
5-20R
GFCI
WH
Module
2
CB 6
CB 2
CB 4-1
Receptacle
BK
5
WH
5-20R
GFCI
WH
Module
5
GFCI
Module
6
BK Receptacle
WH
BL
BL
CB 3
CB 4-2
CB 5
CB 7
RD
RD
6
5-20R
WH
GFCI
Module
7
BK
WH
Receptacle
4
250V 30A
L6-30R
Receptacle
7
5-20R
N-BUSS
RD
Out
CS6369
BK
GN
WH
BK
GFCI
WH
Module
3
WH
CB 1
RD
Receptacle
BK
3
WH
5-20R
In
CS6375
125/250V
50A
3 Pole
4Wire
BK
BK
Receptacle BK
1
WH
5-20R
G-BUSS
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
21
safety products
CCI Mini X-Treme Box
Temporary Power Distribution Unit
with GFCI Protection
Mini X-Treme™ Box
Coleman Cable’s Mini X-Treme Box™ provides more compact and less
costly work-site power distribution than our popular full size models.
Used along with our restoration adapters, these units are ideal for
disaster restoration work where the only available power is from range
outlets, dryer outlets or portable generators. Or, they can be used in
any situation where a more compact, easier-to-handle unit is desired to
safely expand and distribute power on jobsites.
OSHA and NEC Compliant, c(ETL)us Listed, and Certified to CAN/CSA
Reduces electrical hookup and labor time
8 overload, circuit-breaker protected 20 amp straight blade outlets.
All outlets GFCI protected with open neutral and over-voltage protection
Compact size for ease of use
May be used in vertical or horizontal positions
FEATURES
01980
10
22
01980
L14-30P 30A Power Inlet
8 – NEMA 5-20R 20A Power Outlets
2 – 20A Breakers Overload Protection
2 – 20A GFCI auto reset GFCI Protection
11.00
7.125
safety products
Portable Power Cords and
Replacement Plugs/
Ends / Adapters
Power Distribution Extension Cords; Appliance
Cords; Disaster Recovery & Restoration Cords
Rugged temporary power cords for use with the X-Treme Box™ to
handle 50A 3-Pole/4-Wire 125/250v AC; safe appliance extension
cords; cords for use in disaster recovery, restoration, renovation or
maintenance projects requiring temporary, portable power.
FEATURES
Temporary Power Cords - 125/250V/50A, 6/3 - 8/1 AWG
01918 US, 50’, Type STOW
01919 US, 100’, Type STOW
01938 Canada, 50’, Assembled with UL/cUL Components
01939 Canada, 100’, Assembled with UL/cUL Components
01938
Appliance Extension Cords
01854 10’ Dryer Outlet or 30A Straight Generator Outlet
01864 10’ Range Outlet or 50A Straight Generator Outlet
1493 25’ Generator 10/4 STW Yellow Jacket® L14-30P L14-30R*
Disaster Recovery & Restoration Cords - 10/4 SEOOW
01854 10’ 14-30P L1430R UL/CSA
01824 10’ 14-30P CA50A UL/CSA
01864 10’ 14-50P L14-30R UL/CSA
01844 10’ L14-30P CA50A UUCSA
01824
01834 10’ 6/3 & 8/1 SEOW 14-50P CA 50A
1493 25ft Generator* 10/4 STW Yellow Jacket® L14-30P L14-30R*
*UL and cUL Listed
Replacement Plugs/Ends/Adapters
Replacement plugs/ends/adapters constructed with impact and
chemical resistant nylon, designed to keep out moisture and dust.
FEATURES
50A/125/250V 3-Pole/4-Wire Plugs/Connectors/Adapter
05958* Locking Hubbell Male Plug
05959* Locking Hubbell Female Connector
05974* Locking Male Plug
05975* Locking Female Connector
01920 6/4 SEOW 50A “Y” Adapter
05958
05974
*UL and CSA Listed
05959
05975
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
23
safety products
GFCI Outlet Tester
GFCI Outlet Tester
Designed to check the integrity of the wiring for ground fault and
standard outlets. Tests for proper function of GFCI outlets. Features
Power Quality Monitor and Nuisance Trip Test.
FEATURES
30090 012-6
Volts/Amps: 120V/15A
Wiring Diagnostics - Checks Line Neutral and Ground Wire
Integrity
C
US
GFCI Tester - Inspects for proper operation and nuisance tripping.
Separate tests for a 6mA ground fault and a 3mA ground fault
Power Quality Monitor (PQM) - Identifies excessive voltage drop (approx. 6V) on the
branch circuit by measuring the voltage between neutral and ground
30090 012-6


Wired Correctly


Hot To Ground Reversed


Hot To Neutral Reversed

Open Ground

Open Neutral
Open Hot
2.50
2.04
1.68
RESET
TEST
3.70
24
safety products
Digital Monitor
Digital Monitor
This compact, easy to use instrument is made with advanced
microelectronics and provides accurate testing and monitoring of
electrical outlets and systems. Constantly monitors voltage and
frequency indicating potential improper polarity and ground wiring. Its
small size and rugged construction allows for convenient installation in
an electrical outlet or use as a portable service tool.
Voltage is measured as RMS which is much more precise than AC
average. RMS metering is the only method that can accurately
measure all AC power sources. The RMS voltage and frequency
readings are ideal for monitoring modified sine waves such as solidstate generators, inverters and Uninterruptible Power Supply (UPS)
products.
The Digital Monitor display will alternate between line voltage in RMS
volts and line frequency in Hertz. The LCD display shows an “F” in front
of the reading to denote frequency.
Three display modes are available:
Alternating Voltage & Frequency( VOLT/FREQ.)
Voltage only (VOLTAGE)
Frequency only (FREQUENCY)
Pressing the MODE button on the front of the Digital Monitor will cycle
through the display modes. Both voltage and frequency are constantly
monitored regardless of the display mode.
AECM20020
FEATURES
AECM20020
Accurate Testing and Monitoring of All AC Power Source Types
RMS Voltage and Frequency Meter
Multi-tone Fault Alarm
Hands-free Auto Reset
Advanced Microelectronics
One Button Operation
Wiring Diagnostics
LCD Display with LED Backlight
TECHNICAL DATA
Voltage Range
85 to 150 Vac RMS
Frequency Range
40 / 80 Hz
Operating Current
0.02 Amp
Under Voltage Alarm
<102 Vac RMS
Over Voltage Alarm
>135 Vac RMS
Under Frequency Alarm
<55 Hz
Over Frequency Alarm
>65 Hz
Outlet Type
120V/15A single phase
Operating temperature
+32˚F to +125˚F
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
25
safety products
GFCI Panel Mounts
GFCI Panel Mounts
Provides GFCI protection for personnel and equipment when leakage
levels have a potentially lethal ground current in excess of 6
milliamperes. Ideal for equipment where mounting applications require
panel or bulkhead mount. Applications include:
Control Panels
Pumping Systems
32360 001-3
Test Beds
Appliances
Automatic reset on power restoration following disruption of primary
power. 41240-001 is manual reset.
FEATURES
33120 001-3
33240 001-3
32360 001-3
Volts/Amps: 120V/20A
L & N - 12 AWG
Trip Level: 4 - 6 mA
41240 001-3
Volts/Amps: 120V/20A
Trip Level: 4 - 6 mA
Manual Reset
33120 001-3
Volts/Amps: 120V/20A
L & N - 12 AWG
Trip Level: 4 - 6 mA
33240 001-3
Volts/Amps: 240V/20A
L & N - 12 AWG
Trip Level: 4 - 6 mA
41240 001-3
TECHNICAL DATA
32360-001
BLK
WHT
2.51
2.17
RESET
POWER
TEST
3.78
HIGH
VOLTAGE
BLK
WHT
33120 001-3
33240 001-3
Trip response time for ground fault
and grounded neutral trip
less than 25mS
Voltage surge withstand
3kv ringwave test and
4kv/2kA surge immunity test
Radio frequency noise susceptibility operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
MONITOR
3.00
4 Ohms typical
2X ø.185
THRU
GRN
3.38
Grounded Neutral (33120 only)
2.24
2.35
2.04
1.84
1.92
.44
Frequency
50 / 60 Hz
Endurance
3,000 operations minimum
Overload Current
six times rated current
Operating temperature range
-35˚C to 66˚C
Effect of 10 Amp turn DC Shock
on ground fault trip
5% maximum trip level variation
Insulation voltage
1500 VRMS - 1 Min.
Power On indication
lighted indicator
LINE
RESET
TEST
1.02
2.88
15/64"
LOAD
INPUT
.15 DIA (2PL)
2.16
1/4"
25/64"
2.60 3.25
3-1/16"
41240-001
3-11/32"
OUTPUT
1-35/64"
26
1-23/64"
safety products
ELCI Panel Mount
ELCI Panel Mount
Provides protection for equipment when leakage levels exceed 10mA.
Ideal for equipment where mounting applications require panel or
bulkhead mounting. Applications include:
Testing Equipment
Medical Equipment
Appliances
Copiers
Electric Control Panels
Manual reset is required after ELCI trip. Remains reset on power
restoration following disruption of primary power.
FEATURES
24220 100-3
Volts/Amps: 120V/20A or 240V/16A
Trip Level: 10 mA Typical
Accepts 250V female quick disconnect terminals
TECHNICAL DATA
Grounded NeutralVoltage Range
Trip response time for ground fault
Voltage surge withstand
(MOV Protection)
Radio frequency noise susceptibility
Frequency
Endurance
Overload Current
Operating temperature range
Effect of 10 Amp turn DC Shock
on ground fault trip
Insulation voltage
Power On indication
85 - 264 VAC
less than 25mS
3kv ringwave test and
4kv/2kA surge immunity test
operates within normal limits with 0.5 volts
injected on power line 150kHz-230mHz
50 / 60 Hz
5,000 operations minimum
six times rated current
+10˚C to +55˚C
5% maximum trip level variation
24220 100-3
1500 VRMS - 1 Min.
mechanical indicator
1.50
.165
1.16
L
L2/N
LINE
1.54
.65
RESET
RESE
TEST
TES
4.0
E.135
2 HOLES
LOAD
L
1.75
1.93
.54
L2/N
1.25
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
27
safety products
High Power GFCIs
High Power GFCIs
Configured for both in-line and bulk head mount. Engineered to trip
within 25 milliseconds. Protects:
Motors
Pumping Systems
Pressure Washers
Manufacturing Equipment
Welders
Hoists
Has 2’ of cable on both line and load side. Will remain reset on power
restoration following disruption of primary power. Auto reset.
FEATURES
23250 003-1 GFCI
Volts/Amps: 240V/40A
Cord Gauge: 8/3 AWG
Trip Level: 6 mA
Single Phase
C
US
25500 001-1 GFCI
Volts/Amps: 208-240V/30A
Cord Gauge: 10/4 AWG
Trip Level: 4-6 mA
Three Phase
24130 008-1 GFCI
Volts/Amps: 120V/30A
Cord Gauge: 10/3 AWG
Trip Level: 4 - 6 mA
Single Phase
TECHNICAL DATA
24130 008-1
28
Response time for ground fault
Frequency
Endurance
Overload Current
Operating temperature range
Insulation voltage
Power On indication
Drop out voltage
Reset type
Connection type
Enclosure
25mS - typical
50 / 60 Hz
3,000 operations minimum
six times rated current
-20˚C to+40˚C
1500 VRMS - 1 Min.
lighted indicator
60% rated voltage - typical
auto
flying leads
NEMA 4 polymer
safety products
Heavy Duty - High Power ELCIs
30A
Heavy Duty - High Power ELCIs - 30A
Configured for both in-line and bulk head mount. Engineered to trip
within 25 milliseconds. Protects:
Motors
Pumping Systems
Pressure Washers
Manufacturing Equipment
Welders
Hoists
Has 2’ of cable on both line and load side. Will remain reset on power
restoration following disruption of primary power.
FEATURES
24140 002-1 ELCI
Volts/Amps: 240V/30A
Cord Gauge: 10/4 AWG
Trip Level: 10 mA
Single Phase
24500 006-1 ELCI
Volts/Amps: 208-240V/30A
Cord Gauge: 10/4 AWG
Trip Level: 10 mA
Three Phase
TECHNICAL DATA
Response time for ground fault
Frequency
Endurance
Overload Current
Operating temperature range
Insulation voltage
Power On indication
Drop out voltage
Reset type
Connection type
Enclosure
25mS - typical
50 / 60 Hz
3,000 operations minimum
six times rated current
-20˚C to+40˚C
1500 VRMS - 1 Min.
lighted indicator
60% rated voltage - typical
auto
flying leads
NEMA 4 polymer
24140 002-1
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
29
safety products
Heavy Duty - High Power ELCIs
60A
Heavy Duty - High Power ELCIs - 60A
Configured for both in-line and bulk head mount. Engineered to trip
within 25 milliseconds. Protects:
Motors
Pumping Systems
Pressure Washers
Manufacturing Equipment
Welders
Hoists
Has 2’ of cable on both line and load side. To prevent equipment
startup after ELCI trips, manual reset required. Will reset on power
restoration following disruption of primary power.
FEATURES
24520 001-1
Volts/Amps: 120V/60A
Cord Gauge: 4/3 AWG
Trip Level: 10 mA
Single Phase
25560 001-1
Volts/Amps: 380V/60A
Cord Gauge: 4/4 AWG
Trip Level: 30 mA
Three Phase
24530 001-1
Volts/Amps: 240V/60A
Cord Gauge: 4/4 AWG
Trip Level: 10 mA
Three Phase
TECHNICAL DATA
Response time for ground fault
Frequency
Endurance
Overload Current
Operating temperature range
Insulation voltage
Power On indication
Drop out voltage
Reset type
Connection type
Enclosure
TEST
24520 001-1
LOAD
5.54
RESET
LINE
4.00
7.46
8.33
6.97
LINE
30
LOAD
6.98
9.00
9.88
25mS - typical
50 / 60 Hz
3,000 operations minimum
six times rated current
-20˚C to+40˚C
1500 VRMS - 1 Min.
lighted indicator
60% rated voltage - typical
auto
flying leads
NEMA 4 polymer
safety products
Heavy Duty - High Power
GFCI/ELCI Adjustables
Heavy Duty - High Power GFCI/ELCI Adjustables
Configured for both in-line and bulk head mount. Engineered to trip
within 25 milliseconds. Protects:
Motors
Pumping Systems
Pressure Washers
Manufacturing Equipment
Welders
Hoists
Has 2’ of cable on both line and load side. To prevent equipment
startup after GFCI/ELCI trips, manual reset required. Will reset on
power restoration following disruption of primary power. 6.10.30™ key
enables trip level selection and locking at a trip level with key removal.
FEATURES
24396 001-1
Volts/Amps: 277V/30A
Cord Gauge: 10/3 AWG
Trip Level: 6, 10 & 30 mA
Single Phase
24542 001-1
Volts/Amps: 208-240V/60A
Cord Gauge: 4/4 AWG
Trip Level: 6, 10 & 30 mA
Three Phase
24646 001-1
Volts/Amps: 480V/30A
Cord Gauge: 10/4 AWG
Trip Level: 6, 10 & 30 mA
Three Phase
24672 001-1
Volts/Amps: 480V/60A
Cord Gauge: 4/4 AWG
Trip Level: 6, 10 & 30 mA
Three Phase
24846 001-1
Volts/Amps: 208-240V/30A
Cord Gauge: 8/5 AWG
Trip Level: 6, 10 & 30 mA
Three Phase
24846 001-1
LINE
LOAD
5.54
9.00
9.88
RESET
25mS - typical
50 / 60 Hz
3,000 operations minimum
six times rated current
-20˚C to+40˚C
1500 VRMS - 1 Min.
lighted indicator
60% rated voltage - typical
auto
flying leads
NEMA 4 polymer
TEST
TECHNICAL DATA
Response time for ground fault
Frequency
Endurance
Overload Current
Operating temperature range
Insulation voltage
Power On indication
Drop out voltage
Reset type
Connection type
Enclosure
4.00
7.46
8.33
6.97
LINE
LOAD
6.98
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
31
safety products
Heavy Duty - High Power
GFCI/ELCI Adjustables with
Trip Level Selector
Heavy Duty - High Power GFCI/ELCIs with
Trip Level Selector
TRC has engineered a new option for the HD-PRO™ series called
6.10.30™.
Configured for both in-line and bulk head mount. This unique new
design allows the user to select and lock in the most sensitive trip level
at which a specific type of equipment can be operated without
nuisance tripping. Adjustable settings
include trip levels for 6mA, 10mA and 30mA. Trip level flexibility to meet
your needs in one single device - HD-PRO™ with 6.10.30™. 6.10.30™
key enables trip level selection and locking at a trip level with key
removal. Protects:
Motors
Portable Conveyors
Pumping Systems
Welders
Pressure Washers
Freight Lifts
FEATURES
24946 003-1
GREEN
GREEN
RED
RED
WHITE
WHITE
BLACK
BLACK
LINE
9.54
13.00
13.88
32
3/8
3.00
10.33
BLACK
RESET
3/8
3.00
TEST
BLACK
9.00
RED
WHITE
9.46
GREEN
RED
WHITE
LOAD
6.00
GREEN
24946 003-1
Volts/Amps: 600V/60A
Cord Gauge: 4/4 AWG
Trip Level: 6, 10 & 30 mA
Three Phase
24786 001-1
Volts/Amps: 208-240V/80A
Cord Gauge: 4/4 AWG
Trip Level: 6, 10 & 30 mA
Three Phase
24992 001-1
Volts/Amps: 600V/80A
Cord Gauge: 4/4 AWG
Trip Level: 6, 10 & 30 mA
Three Phase
24796 001-1
Volts/Amps: 480V/80A
Cord Gauge: 4/4 AWG
Trip Level: 6, 10 & 30 mA
Three Phase
24994 001-1
Volts/Amps: 600V/100A
Cord Gauge: 2/4 AWG
Trip Level: 6, 10 & 30 mA
Three Phase
TECHNICAL DATA
LINE
LOAD
7.10
10.97
24736 001-1
Volts/Amps: 480V/100A
Cord Gauge: 2/4 AWG
Trip Level: 6, 10 & 30 mA
Three Phase
Response time for ground fault
Frequency
Endurance
Overload Current
Operating temperature range
Insulation voltage
Power On indication
Drop out voltage
Reset type
Connection type
Enclosure
25mS - typical
50 / 60 Hz
3,000 operations minimum
six times rated current
-20˚C to+40˚C
1500 VRMS - 1 Min.
lighted indicator
60% rated voltage - typical
auto
flying leads
NEMA 4 polymer
safety products
High Power Equipment Ground Fault
Protective Devices (EGFPD) and
GFCI/ELCI Adjustables
High Power Equipment Ground Fault Protective
Devices (EGFPD) and GFCI/ELCI Adjustables
Configured for both in-line and bulk head mount. Engineered to trip
within 25 milliseconds. Protects:
Motors
Pumping Systems
Pressure Washers
Manufacturing Equipment
Welders
Hoists
To prevent equipment startup after EGFPD or GFCI/ELCI trips, manual
reset required. Will reset on power restoration following disruption of
primary power. Key enables trip level selection and locks at a trip level
with key removal.
FEATURES
44110 012-1 EGFPD*
Volts/Amps: 208-240V/30A
Trip Level: 10, 30 & 50 mA
Three Phase
44610 001-1 GFCI/ELCI
Volts/Amps: 208-240V/30A
Trip Level: 6,10 & 30 mA
Three Phase
44140 012-1 EGFPD*
Volts/Amps: 208-240V/60A
Trip Level: 10, 30 & 50 mA
Three Phase
44640 001-1 GFCI/ELCI
Volts/Amps: 208-240V/60A
Trip Level: 6,10 & 30 mA
Three Phase
44120 012-1 EGFPD*
Volts/Amps: 480V/30A
Trip Level: 10, 30 & 50 mA
Three Phase
44620 001-1 GFCI/ELCI
Volts/Amps: 480V/30A
Trip Level: 6,10 & 30 mA
Three Phase
44130 012-1 EGFPD*
Volts/Amps: 480V/60A
Trip Level: 10, 30 & 50 mA
Three Phase
44630 001-1 GFCI/ELCI
Volts/Amps: 480V/60A
Trip Level: 6,10 & 30 mA
Three Phase
44110 012-1
9.84”
5.91”
*
C
US
TECHNICAL DATA
Response time for ground fault
Frequency
Endurance
Overload Current
Operating temperature range
Insulation voltage
Power On indication
Drop out voltage
Reset type
Connection type
Enclosure
11.81”
25mS - typical
50 / 60 Hz
3,000 operations minimum
six times rated current
-20˚C to+40˚C
1500 VRMS - 1 Min.
lighted indicator
60% rated voltage - typical
auto
user attachable
NEMA 4 16 gauge steel
Allowed space
for conduit
attachment
holes
Front View
Right Side View
PANEL MOUNT STUDS, 10-32
Allowed space for
conduit attachment
holes
Bottom View
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
33
safety products
Wiring Instructions for
High Power GFCI/ELCIs
All high power GFCI/ELCIs must be suited for use
with solidly grounded systems. The power cords must
be connected according to the wiring instructions
shown below.
WIRING INSTRUCTIONS
120V, 277V UNIT
240V 1 UNIT
208/240V 3 UNIT*
208/480/600V 3 UNIT
1. Black = Line
2. White = Neutral
3. Green = Ground
1. Black = Line
2. Red (Pink) = Line
3. White = Neutral
4. Green = Ground
1.Black = Line
2.Red (Pink) = Line
3.Orange (Blue) = Line
4.White = Neutral
5.Green = Ground
1.Black = Line
2.Red (Pink) = Line
3.White = Line
4.Green = Ground
CIRCUITRY TYPE
Single Phase
Type A
V = 120
V = 277
Single Phase
Type B
V = 240
Three Phase
Type C
V = 208 / 240
480 / 600
Three Phase
Type D
V = 208 / 240
480 / 600
* Grounding Point May Vary
34
safety products
Heavy Duty Three Wire
Extension Cord Set
Heavy Duty Three Wire Extension Cord Set
Protects all equipment powered by industrial-duty extension cords
with highest degree of electrical shock and cord fire prevention. Cord
leakage monitoring prevents electrical fires resulting from series or
cross line faults. GFCI shock protection for personnel meets OSHA
and NEC regulations and protects devices plugged into it.
Applications include:
Fans
Power Tools
Blowers
Heaters
Saws
Basement & Garage Work Sites
Standard length is 25’. To prevent unmonitored equipment startup,
manual reset is required after GFCI trip and power outage. Outdoor
rated trip unit.
FEATURES
14880 035-2
Volts/Amps: 125V/15A
Cord Gauge:14/3 AWG.
NEMA 5 - 15P&R
Ground Fault Trip Level: 4 - 5.2 mA
Cord Leakage Trip Level: 2 - 2.6 mA
14880 035-2
TECHNICAL DATA
Grounded neutral
Trip response time for ground fault,
cord leakage, grounded neutral trip
Voltage surge withstand
(MOV Protection)
Radio frequency noise susceptibility
Frequency
Endurance
Overload Current
Operating temperature range
Effect of 10 Amp turn DC Shock
on ground fault trip
Insulation voltage
Power On indication
4 Ohms typical
less than 25mS
3kv ringwave test and
4kv/2kA surge immunity test
operates within normal limits with 0.5 volts
injected on power line 150-230mHz
50 / 60 Hz
3,000 operations minimum
six times rated current
-35°C to 66°C
5% maximum trip level variation
2.05
1.68
3.70
25’
2.72
1500VRMS - 1Min.
mechanical indicator
1.57
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
35
safety products
Fire Shield® Surge Strips
The World’s Safest Surge Strips
Fire Shield® Surge Strips are the only power strips with built-in
intelligence to prevent:
Cord Fires
Surges
Overloads
State-of-the-art electronics detect cord damage and disconnect power
in 25/1000 of a second, preventing cord fires. Every six minutes there is
a cord-related fire in the United States.
The special braided shield allows the plug-mounted electronics to
continuously monitor for insulation breakdown or broken/frayed
conductors. Standard electrical cords have no means of monitoring for
leakage currents and cannot shut off power before these currents can
arc and start a fire.
Protect all your sensitive electronic equipment from the damaging
effects of power surges and spikes.
FEATURES
90802-3FA
90802-3FA
1350 Joules
$25,000 Connected
Equipment Warranty
3 Foot Cord
6-Outlet
90885-1
90814-2FA
Coax/Cable/Phone Fax/Modem
Protection
3500 Joules
$75,000 Connected
Equipment Warranty
6 Foot Cord
8-Outlet
90885-1
1350 Joules
$25,000 Connected
Equipment Warranty
12 Foot Cord
6-Outlet
90814-2FA
TECHNICAL DATA
90814-2
36
6 FT NOM.
90802-3/90885-3
125V/15A
3kv 50 / 60 Hz test
6,000 Volts
14/3 AWG
3 wire
3 FT or 12 FT
State-of-the-art electronics
detect cord damage by sensing
leakage currents in the special
braided monitoring shield and
disconnect power. The circuitry
commands a set of contacts
to open within 25/1000ths of
a second after detecting a
problem, faster than you can
blink your eye.
Volts/Amps
Frequency
Maximum Surge
Cord Gauge
Conductors
safety products
Yellow Jacket® Cable Protection
System
Yellow Jacket® Cable Protection System
A complete cable protection system. Perfect for any application where
cables are in harms way. Eliminates downtime, costly repairs and
reduces liability. Applications for:
Entertainment Industry
Institutions and Municipalities
Industrial, Construction and Utilities
FEATURES
Reduces risk of electrocution and entanglement hazards while protecting cable for
power, fluids and communications
Designed for harsh demanding environments
Non-conductive, resists oils and solvents
Available in both three and five channel configurations, cables lay flat and unkinked
in thier own channel
Modular design makes installation simple and fast in virtually any configuration
The Yellow Jacket has a load bearing capacity of 80,000 lbs., or 21,000 lbs. per axle.
31104
MODEL
31104-1
DESCRIPTION
LENGTH
WIDTH
HEIGHT
WEIGHT
SLOT SIZE
# OF SLOTS
Linear
36”
19”
2”
31 lbs.
1.25”
5
31107-1
End Cap Set
6”
19”
2”
8 lbs.
1.25”
5
31106-1
Right Turn
25”
19”
2”
17 lbs.
1.25”
5
31105-1
Left Turn
25”
19”
2”
17 lbs.
1.25”
5
31112-1*
T-Section
38”
38”
2”
42 lbs.
1.25”
5
31100-1
Linear
36”
20”
3”
34 lbs.
2.25”
3
31103-1
End Cap Set
6”
20”
3”
19 lbs.
2.25”
3
31102-1
Right Turn
25”
20”
3”
23 lbs.
2.25”
3
31101-1
Left Turn
25”
20”
3”
23 lbs.
2.25”
3
* Yellow Jacket has all female connectors.
Black Jacket™ Light Duty Cable Protector
Load bearing capacity of 10,000 lbs.per axle. Not compatible with
Yellow Jacket Connectors. Compatible with other manufacturers.
31108
MODEL
31108-1
DESCRIPTION
LENGTH
WIDTH
HEIGHT
WEIGHT
SLOT SIZE
# OF SLOTS
Linear
36”
19”
2”
22 lbs.
1.25”
5
31109-1
End Cap Set
6”
19”
2”
7 lbs.
1.25”
5
31110-1
‘Y’ for Left &
Right Turns
22”
22”
2”
13 lbs.
1.25”
5
31113-1*
T-Section
17.5”
17.5”
2”
13 lbs.
1.25”
5
* Black Jacket has one female connector and three male connectors.
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
37
safety products
Definitions & Standards
Definitions & Standards
GFCI
A Ground Fault Circuit Interrupter is an LCPD specifically intended for the protection of
people from shock hazard. A GFCI is a device that will immediately stop the flow of
electricity if it senses any voltage loss, whether the loss is through the ground wire or to
your body.
ELCI
Equipment Leakage Circuit Interrupters are a class of LCPD not considered to be “people
protectors,” and are generally only intended for equipment protection. ELCIs are virtually
identical with ALCIs with the exception that the trip level is set higher than 6mA.
ALCI
Appliance Leakage Current Interrupters are a class of leakage current protection devices
closely related to GFCIs. In fact, they share the same limits for trip level and response time.
The main difference is that ALCI’s are intended for use only in circuits with a solidly
grounded neutral conductor.
LCDI
Leakage Current Detection Interrupter cord sets are intended to sense leakage currents
flowing between or from conductors of the cord set and interrupt the circuit.
AFCI
Arc Fault Circuit Interrupters are designed to mitigate the affect of electrical arcs. Defined
by UL 1699 they can be provided as circuit breakers, outlet devices, combination devices,
adapters and cord sets. The AFCI must differentiate a normal arc (i.e., power tool, light
switch, etc.) from a bad arc (i.e., a parallel fault in the wiring). To avoid nuisance tripping,
the trip levels are quite higher and time longer than GFCIs, ALCIs or LCDIs. A cord type
AFCI’s maximum trip level is 75A for parallel fault and 5A for a series fault, both of which
could be a fire in progress.
PRCD
Portable Residual Current Devices are designed for use in international applications and
intended to protect people from electrical shock by interrupting the electrical circuit to a
load when a fault current exceeds its rated trip level. They are compliant with IEC and
NEMA standards, depending upon your country of use, and are available in 120V to 230V
versions with 6-30mA trip levels.
UL Standards
UL Listed products are used in applications where the product is not an integral part of the
manufactured system. UL Listed wire and cable products are intended for use within
residential, commercial or industrial buildings
OSHA Regulations
OSHA’s scope of regulation covers three major business areas; the Construction Industry,
the Maritime Industry and a third category, General Industry, which covers most other
business enterprises except for those in mining and agriculture which are overseen by
other government agencies. OSHA’s regulations are Federal Law and are contained in the
U.S. Government’s Code of Federal Regulations (CFR). Violations of OSHA regulations can
subject companies to legal action and fines.
NEC (National Electrical Code) Standards
The National Electrical Code (NEC®) requires use of listed products to meet the
requirements of various “Articles” within the code.
38
safety products
OSHA Regulations
OSHA Regulations
Ground Fault Protection
29CFR1910.304(b)(3)(ii)(A) All 125-volt, single-phase, 15-, 20-, and 30-ampere receptacle outlets that are
not part of the permanent wiring of the building or structure and that are in use by personnel shall have
ground-fault circuit-interrupter protection for personnel.
Note 1 to paragraph (b)(3)(ii)(A) of this section: A cord connector on an extension cord set is considered to be a receptacle outlet if
the cord set is used for temporary electric power.
Note 2 to paragraph (b)(3)(ii)(A) of this section: Cord sets and devices incorporating the required ground-fault circuit-interrupter that
are connected to the receptacle closest to the source of power are acceptable forms of protection.
29CFR1910.304(b)(3)(ii)(B) Receptacles other than 125 volt, single-phase, 15-, 20-, and 30-ampere
receptacles that are not part of the permanent wiring of the building or structure and that are in use by
personnel shall have ground-fault circuit-interrupter protection for personnel.
29CFR1910.304(b)(3)(ii)(C) Where the ground-fault circuit-interrupter protection required by paragraph
(b)(3)(ii)(B) of this section is not available for receptacles other than 125-volt, single-phase, 15-, 20-, and 30ampere, the employer shall establish and implement an assured equipment grounding conductor program
covering cord sets, receptacles that are not a part of the building or structure, and equipment connected by
cord and plug that are available for use or used by employees on those receptacles. This program shall
comply with the following requirements (2 pages…)
1926.404(b)(ii) Ground-fault circuit interrupters. All 120-volt, single-phase, 15- and 20-ampere receptacle
outlets on construction sites, which are not a part of the permanent wiring of the building or structure and
which are in use by employees, shall have approved ground-fault circuit interrupters for personnel protection.
Receptacles on a two-wire, single-phase portable or vehicle-mounted generator rated not more than 5kW,
where the circuit conductors of the generator are insulated from the generator frame and all other grounded
surfaces, need not be protected with ground-fault circuit interrupters.
Cord Protection
29CFR1910.304(b)(1) Examination. Electric equipment shall be free from recognized hazards that are likely to
cause death or serious physical harm to employees. Safety of equipment shall be determined using the
following considerations:
(viii) Other factors that contribute to the practical safeguarding of persons using or likely to come in contact
with the equipment.
(7) Mechanical execution of work. Electric equipment shall be installed in a neat and workmanlike manner.
29CFR1910.305(a)(2)(x) Flexible cords and cables shall be protected from accidental damage, as might be
caused, for example, by sharp corners, projections, and doorways or other pinch points.
29CFR1910.305(a)(2)(xi) Cable assemblies and flexible cords and cables shall be supported in place at
intervals that ensure that they will be protected from physical damage. Support shall be in the form of staples,
cables ties, straps, or similar type fittings installed so as not to cause damage.
1926.403(b)(1) the employer shall ensure that electrical equipment is free from recognized haards that are
likely to cause death or serious physical harm to employees. Safety equipment shall be determined on the
basis of the following considerations:
(vii) Other factors which contribute to the practical safeguarding of employees using or likely to come in
contact with the equipment.
29CFR1926.405(a)(2)(ii)(B) Branch circuits shall originate in a power outlet or panelboard. Conductors shall
be run as multiconductor cord or cable assemblies or open conductors, or shall be run in raceways. All
conductors shall be protected by overcurrent devices at their ampacity. Runs of open conductors shall be
located where the conductors will not be subject to physical damage, and the conductors shall be fastened at
intervals not exceeding 10 feet (3.05 m). No branch-circuit conductors shall be laid on the floor. Each branch
circuit that supplies receptacles or fixed equipment shall contain a separate equipment grounding conductor if
the branch circuit is run as open conductors.
29CFR1926.416(e)(1) Worn or frayed electric cords or cables shall not be used.
Coleman Cable Inc.
800.323.9355 • www.colemancable.com
39
Visit us online at www.colemancable.com
• Complete online catalog
• Downloadable spec sheets
• Technical reference
• Compliance information
• Rep locator
• Online training
Quick Tracking
• No login required
• Track by P.O.#
• Real-time order status
All-Access Login
• Check pricing & availability
• Create a favorites list
• Place an order
• Check detailed order status
A Tradition of Excellence...
Exceptional Performance
• Established Market Presence
• Diverse Product Line
• Leading Brands
• World Class Manufacturing
• Best in Class Logistics
• State-Of-The-Art-Processes
Coleman Cable Inc. • 1530 Shields Drive • Waukegan, IL 60085 • 800.323.9355 • www.colemancable.com
LT211-12-01 APR13 RV2
Download PDF
Similar pages