Brosur FL/MCP/MMF301

FL/MCP-301/Rev1

FL/MCP/MMF301

Call Point

Analogue Addressable Module

Addressable Devices

General

FL/MCP/MMF301 without an integral isolator is a call point designed to provide a manual alarm interface to a Firelite's fire alarm control panel.

Installation efficiency and flexibility is offered at the heart of the call point range.

Both break glass and resettable operating elements can be used in the standard unit.

Operation of the re-settable element is indicated by a yellow strip on the element which becomes visible when activated. With the addition of a hinged transparent cover the element may be protected against accidental operation and may be further protected by using a cover seal which requires breaking in order to operate the unit.

Installation

The call point uses one of 159 possible addresses which is simply 'dialled in' using the two rotary decade switches on the rear of the unit.

A specialist test key may be inserted into the bottom of the unit to lower the resettable flex portion and release the micro-switch and thus a full functional test is achieved.

These call points are suitable for semiflush mounting as standard, for indoor use. This uses a single-gang electrical knock-out box in conjunction with a terminal tray for isolated screen continuity connection. However if surface mounting is required, then a matching single terminal back box is also available.

Mounting hardware and installation instructions are provided with each module.

Features

Ÿ

Ÿ

Unique 'Plug & Play' installation concept

Re-settable operating element option

Ÿ Analogue addressable communications

Ÿ Semi-Flush or surface Mounting

Ÿ

Ÿ

Backward compatibility

Enhanced aesthetics

Ÿ Extended warranty

Specifications

Ÿ Dimensions:

Semi-flush mounting: 89(w) x 93(h) x 27.5(d)

Surface mounting: 89(w) x 93(h) x 59.5(d)

Ÿ Weight :

Flush 125g

Surface 175g

Ÿ Mounting hole centres:

60mm

Ÿ Current Consumption:

Quiescent (without isolator)- 375μA

Alarm Current: 600μA

Ÿ Operating Voltage :

15 V to 30VDC maximum

Ÿ

Ÿ

Environmental Limits:

0°C to +49°C operating temperature

10% to 93%, non-condensing relative humidity

Ingress Protection (IP) Rating : IP24D

Page 1 of 2 — FL/MCP-301/Rev1 Oct2011

89 mm 27.5 mm 32.0mm

Wiring Diagram

+ -

Address

Selection dials

UL compatible control panel

+

-

To next device

Ordering Information

Part No.

FL /MCP-SF/ MMF-301

FL /MCP-FF/ MMF-301

FL /MCP-SG/ MMF-301

FL /MCP-FG/ MMF-301

Description

Intelligent call point without isolator, LiteSpeed™ Protocol, with in-built back box , Surface mount, with Flexi element

Intelligent call point without isolator, LiteSpeed™ Protocol, without back box , Semi-Flush mount mount, with Flexi element

Intelligent call point without isolator, LiteSpeed™ Protocol, with in-built back box , Surface mount, with Glass element

Intelligent call point without isolator, LiteSpeed™ Protocol, without back box , Semi-Flush mount mount, with Glass element

Fire·Lite® and LiteSpeed® are registered trademarks and FireWatch™ is a trademark of Honeywell International Inc.

©2010 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited.

This document is not intended to be used for installation purposes.

We try to keep our product information up-to-date and accurate.

We cannot cover all specific applications or anticipate all requirements.

All specifications are subject to change without notice.

support.ssi@h oneywell.com

Page 2 of 2 — FL/MCP-301/Rev1 Oct2011