WSR 36-A
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
1 Information about the documentation
1.1 About this documentation
•
•
•
Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free
handling and use of the product.
Observe the safety instructions and warnings in this documentation and on the product.
Always keep the operating instructions with the product and make sure that the operating instructions
are with the product when it is given to other persons.
1.2 Explanation of signs used
1.2.1 Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words
are used in combination with a symbol:
DANGER! Draws attention to imminent danger that will lead to serious personal injury or fatality.
WARNING! Draws attention to a potential hazard that could lead to serious personal injury or
fatality.
CAUTION! Draws attention to a potentially dangerous situation that could lead to minor personal
injury or damage to the equipment or other property.
1.2.2 Symbols in the documentation
The following symbols are used in this document:
Read the operating instructions before use
Instructions for use and other useful information
1.2.3 Symbols in the illustrations
The following symbols are used in illustrations:
These numbers refer to the corresponding illustrations found at the beginning of these operating
instructions.
The numbering reflects the sequence of operations shown in the illustrations and may deviate
from the steps described in the text.
Item reference numbers are used in the overview illustrations and refer to the numbers used in
the product overview section.
These characters are intended to specifically draw your attention to certain points when handling
the product.
1.3 Product-dependent symbols
1.3.1 Symbols on the product
The following symbols are used on the product:
Stroke rate
Direct current (DC)
1.4 Product information
Hilti products are designed for professional use and may be operated, serviced and maintained only by
trained, authorized personnel. This personnel must be informed of any particular hazards that may be
encountered. The product and its ancillary equipment can present hazards if used incorrectly by untrained
personnel or if used not in accordance with the intended use.
The type designation and serial number are stated on the rating plate.
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
1
▶
Write down the serial number in the table below. You will be required to state the product details when
contacting Hilti Service or your local Hilti organization to inquire about the product.
Product information
Reciprocating saw
Generation:
Serial no.:
WSR 36­A
01
1.5 Declaration of conformity
We declare, on our sole responsibility, that the product described here complies with the applicable directives
and standards. A copy of the declaration of conformity can be found at the end of this documentation.
The technical documentation is filed and stored here:
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany
2 Safety
2.1 General power tool safety warnings
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
▶ Keep work area clean and well lit. Cluttered or dark areas invite accidents.
▶ Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
▶ Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
Electrical safety
▶ Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
▶ Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
▶ Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
▶ Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the
risk of electric shock.
▶ When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
▶ If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
Personal safety
▶ Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury.
▶ Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
▶ Prevent unintentional starting. Ensure the switch is in the off‐position before connecting to power
source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on
the switch or energising power tools that have the switch on invites accidents.
▶ Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
▶ Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
2
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
▶
▶
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and collection facilities, ensure these
are connected and properly used. Use of dust collection can reduce dust-related hazards.
Power tool use and care
▶ Do not force the power tool. Use the correct power tool for your application. The correct power tool will
do the job better and safer at the rate for which it was designed.
▶ Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
▶ Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
▶ Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
▶ Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and
any other condition that may affect the power tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly maintained power tools.
▶ Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
▶ Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
Battery tool use and care
▶ Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with another battery pack.
▶ Use power tools only with specifically designated battery packs. Use of any other battery packs may
create a risk of injury and fire.
▶ When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects, that can make a connection from one terminal to
another. Shorting the battery terminals together may cause burns or a fire.
▶ Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
Service
▶ Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
2.2 Safety instructions for jig saw / reciprocating saw
▶
Hold power tool by insulated gripping surfaces, when performing an operation where the cutting
accessory may contact hidden wiring. Cutting accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the operator an electric shock.
2.3 Additional safety instructions
Personal safety
▶ Use clamps or another practical way to secure and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves it unstable and may lead to loss of control.
▶ Modification of the power tool is not permitted.
▶ Wear ear protectors. Exposure to noise can cause hearing loss.
▶ Respiratory protection must be worn if the power tool is used without a dust removal system for
work that creates dust.
▶ Improve the blood circulation in your fingers by relaxing your hands and exercising your fingers
during breaks between working.
▶ Secure the workpiece. Use clamps or a vice to secure the workpiece. The workpiece is thus held
more securely than by hand and both hands remain free to operate the tool.
▶ The power tool is not intended for use by inexperienced persons who have received no special
training.
▶ Keep the power tool out of reach of children.
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
3
▶
▶
▶
▶
▶
▶
▶
Wear protective gloves when changing accessory tools as accessory tools get hot during use and
cutting edges of saw blades are sharp.
Switch the product on only after bringing it into the working position.
Never use the power tool without the hand guard fitted.
Engage the transport lock before storing or transporting the tool.
Avoid unintentional starting. Don’t carry the tool with your finger on the control switch. Remove the
battery from the power tool during work breaks, before carrying out maintenance, before changing
accessory tools and before transporting the power tool.
Observe the national health and safety requirements.
Dust from materials, such as paint containing lead, some wood species, concrete / masonry / stone
containing silica, and minerals as well as metal, may be harmful. Contact with or inhalation of the dust
may cause allergic reactions and/or respiratory or other diseases to the operator or bystanders. Certain
kinds of dust are classified as carcinogenic such as oak and beech dust, especially in conjunction with
additives for wood conditioning (chromate, wood preservative). Material containing asbestos may be
handled only by specialists. Use a dust removal system whenever possible. To achieve a high level
of dust collection, use a suitable vacuum cleaner. When indicated, wear a respirator appropriate
for the type of dust generated. Ensure that the workplace is well ventilated. Follow national
requirements for the materials you want to work with.
Electrical safety
▶ Before beginning work, check the working area (e.g. using a metal detector) to ensure that no
concealed electric cables or gas and water pipes are present. External metal parts of the power tool
may become live, for example, when an electric cable is damaged accidentally. This presents a serious
risk of electric shock.
Special safety instructions for reciprocating saws
▶ Always guide the power tool away from your body when working with it.
▶ Never position your hands ahead of or on the saw blade.
▶ Never cut into unknown materials and keep the line of cut above and below the workpiece free of
obstacles. If the saw blade strikes an object it may cause the power tool to kick back.
▶ Apply moderate pressure and select a suitable stroke rate when using the pipe-cutting adapter
(accessory), especially when cutting large-diameter pipes. This will help to prevent the power tool
overheating.
▶ Warning! When cutting through pipes, e.g. when carrying out demolition or installation work,
check to ensure that the pipes no longer contain liquids and empty them if necessary. When
cutting through pipes, hold the power tool above the level of the pipe you are cutting through.
The power tool incorporates no protective measures to prevent ingress of water or dampness. Liquids
running out of pipes may cause a short circuit in the power tool.
▶ Do not attempt to cut material thicker than the specified max. thickness for which the saw is
designed and do not use unsuitable saw blades (reciprocating saw blades of the wrong size or not
equipped with a 1/2" connection end).
Careful handling and use of batteries
▶ Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.
▶ Do not expose batteries to high temperatures and keep them away from fire. There is a risk of
explosion.
▶ Avoid ingress of moisture. Ingress of moisture may cause a short circuit, resulting in burning injuries or
fire.
▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over
80°C (176°F). This presents a risk of fire, explosion or injury through contact with caustic substances.
▶ Never continue to use or attempt to charge damaged batteries, e.g. batteries with cracks, broken
parts, bent or pushed-in / pulled-out contacts).
▶ Do not use the battery as a power source for other unspecified power tools or appliances.
▶ If the battery is too hot to touch it may be defective. In this case, place the power tool in a nonflammable location, well away from flammable materials, where it can be kept under observation
and allowed to cool down. Contact Hilti Service after the battery has cooled down.
4
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
5
6
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
3 Description
3.1 Overview of the product
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
7
@
;
=
%
&
(
)
+
Chuck (blade holder)
Hand guard with chuck (blade holder) cover
Stroke rate regulator
Control switch
Safety lock
Rating plate
Grip
Battery release button
§
/
:
∙
$
£
|
Battery state of charge display
Battery
Air vents
Forward gripping area (hand guard)
Contact shoe adjustment button
Contact shoe
Saw blade
3.2 Intended use
The product described is a cordless reciprocating saw. It is designed for cutting wood, wood-like materials,
metals and plastics.
The product is designed for two-handed operation.
▶
▶
Use only Hilti Li-ion batteries from the B 36 series with this product.
Use only the Hilti battery chargers from the C4/36 series for these batteries.
3.3 Possible misuse
▶
▶
▶
Do not use the power tool to cut bricks, concrete, cellular concrete, natural stone or tiles.
Do not use the product to cut pipes that still contain liquids.
Do not saw into unknown materials.
3.4 Lithium­ion battery status display
The charge state of the Li-ion battery and malfunctions of the power tool are indicated by the display on
the Li­ion battery. The charge state of the Li­ion battery is displayed after pressing one of the two battery
release buttons.
Status
Meaning
3 LEDs light up.
•
4 LEDs light up.
2 LEDs light up.
1 LED lights.
1 LED blinks.
1 LED blinks, the power tool is not ready for use.
4 LEDs blink, the power tool is not ready for use.
•
Charge state: 75 % to 100 %
•
Charge state: 25 % to 50 %
•
•
•
•
Charge state: 50 % to 75 %
Charge state: 10 % to 25 %
Charge state: < 10 %
The battery has overheated or is completely
discharged.
The power tool is overloaded or has overheated.
Note
Battery charge state cannot be displayed while the control switch is pressed and for up to 5 seconds
after releasing the control switch. If the battery display LEDs blink, please observe the instructions
given in the Troubleshooting section.
3.5 Items supplied
Reciprocating saw, saw blade, operating instructions.
Note
To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare
parts, consumables and accessories approved by Hilti for use with the product can be found at your
local Hilti Center or online at: www.hilti.group
3.6 Stroke rate setting
Material to be cut
Suggested stroke rate settings
Wood containing nails
5-6
Wood
Interior finishing, drywall
8
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
5-6
3-4
Material to be cut
Suggested stroke rate settings
Steel
2-3
Plastic
Non-ferrous metals
Aluminium
Stainless steel
3-4
2-3
2-3
1
4 Technical data
4.1 Reciprocating saw
Rated voltage
Weight in accordance with EPTA procedure 01
Stroke rate
Stroke
Keyless chuck for standard accessory tools
WSR 36­A
36 V
4.37 kg
0 /min …2,850 /min
32 mm
1/2 in
4.2 Noise information and vibration values in accordance with EN 60745
The sound pressure and vibration values given in these instructions were measured in accordance with a
standardized test and can be used to compare one power tool with another. They can also be used for a
preliminary assessment of exposure. The data given represents the main applications of the power tool.
However, if the power tool is used for different applications, with different accessory tools, or is poorly
maintained, the data can vary. This can significantly increase exposure over the total working period. An
accurate estimation of exposure should also take into account the times when the tool is switched off, or
when it is running but not actually being used for a job. This can significantly reduce exposure over the
total working period. Identify additional safety measures to protect the operator from the effects of noise
and/or vibration, for example: Maintaining the power tool and accessory tools, keeping the hands warm,
organization of work patterns.
Noise information
Sound (power) level (LWA)
Uncertainty for the sound power level (KWA)
Sound pressure level (LpA)
Uncertainty for the sound pressure level (KpA)
Vibration information
Vibration emission value for sawing chipboard (ah,B)
Vibration emission value for sawing wood beams
(ah,WB)
Uncertainty (K)
WSR 36­A
101 dB(A)
3 dB(A)
90 dB(A)
3 dB(A)
WSR 36­A
13 m/s²
16 m/s²
1.5 m/s²
5 Operation
5.1 Safe operation
CAUTION
Risk of injury! Inadvertent starting of the product.
▶
Remove the battery before making any adjustments to the power tool or before changing
accessories.
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
9
WARNING
Risk of injury! Danger of kickback.
▶
Always use saw blades of adequate length. The tip of the blade must project at least 40 mm (1¹/₂")
beyond the reverse side of the workpiece during the blade stroke.
WARNING
Risk of injury! Caused by the chuck / accessory tool retaining mechanism
▶
Always hold the power tool securely with both hands on the grips provided. Never use the power
tool without a fully functional hand guard.
WARNING
Risk of injury by the blade holder / chuck
▶
Do not use the cover over the blade holder / chuck as a gripping area.
Note
The power tool must be pressed against the workpiece until the contact shoe makes firm
contact. This helps ensure maximum safety and good performance.
Observe all safety instructions printed in this documentation and on the tool.
▶
10
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
5.2 Removing the battery
1. Press the two release buttons and hold them in the pressed position.
2. Pull the battery out of the product to the rear.
5.3 Fitting the saw blade
Note
Use only saw blades equipped with a 1/2" connection end.
1. Engage the transport lock.
2. Check that the connection end of the accessory tool is clean and lightly greased. Clean it and grease it if
necessary.
3. Turn the chuck locking sleeve counterclockwise and hold it in this position.
4. Push the saw blade into the chuck from the front end of the tool.
5. Release the locking sleeve and allow it to click back and engage in its original position.
6. Grip and pull the saw blade to check that it is locked in position.
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
11
5.4 Removing the saw blade
1.
2.
3.
4.
Engage the transport lock.
Turn the chuck locking sleeve counterclockwise and hold it in this position.
Pull the blade forward out of the chuck.
Release the locking sleeve and allow it to move back to its original position.
5.5 Adjusting the contact shoe
Note
When the contact shoe is adjusted correctly the length of the blade can be used optimally and access
in corners is improved. The contact shoe engages in click-stop increments of 6 mm (¹⁵/₆₄").
Do not adjust the contact shoe while the power tool is in operation.
1.
2.
3.
4.
5.
6.
Engage the transport lock.
Remove the saw blade.
Press the contact shoe adjustment button and hold it in this position.
Slide the contact shoe to the desired position.
Release the contact shoe adjustment button.
Grip and pull the contact shoe to check that it is locked in position.
5.6 Adjusting the stroke rate
Note
Please refer to the application table for the recommended stroke rate settings.
1. Set the stroke rate to a setting between 1 (low) and 6 (high) by turning the stroke rate regulator.
12
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
2. Press the control switch.
Note
The power tool will then run at the preselected stroke rate.
5.7 Pipe-cutting adapter (accessory)
1.
2.
3.
4.
5.
6.
7.
8.
9.
Engage the transport lock.
Remove the saw blade.
Press the contact shoe adjustment button and hold it in this position.
Pull the contact shoe forward, away from the power tool.
Push the pipe-cutting adapter onto the front end of the power tool and bring it into the desired position.
Release the contact shoe adjustment button.
Grip and pull the pipe-cutting adapter to check that it is locked in position.
Release the screw clamp on the pipe-cutting adapter fully.
Place the chain around the pipe and hook it back onto the pipe-cutting adapter.
Note
The clamping screw should lie at an angle of 45° to the power tool.
10. Close the clamping screw.
5.8 Inserting the battery
WARNING
Electrical hazard! Risk of short circuiting.
▶
Before inserting the battery, check to ensure that the battery terminals and the contacts on the
reciprocating saw are free from foreign objects.
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
13
WARNING
Risk of injury! Hazard presented by a falling battery.
▶
A falling battery may present a risk of injury to yourself and others. Check that the battery is
securely seated in the reciprocating saw.
Push the battery into the product from the rear as far as it will go and until it is heard to engage with a
double click.
▶
5.9 Switching on
1. Disengage the transport lock.
2. Press the control switch.
5.10 Switching off
WARNING
Risk of injury! Caused by the saw continuing to run.
▶
▶
Do not lift the product away from the workpiece until it has stopped completely.
Wait until the product stops completely before you lay it down.
1. Release the control switch.
2. Engage the transport lock.
5.11 Plunge cutting
WARNING
Risk of injury! Risk of kickback.
▶
Apply the appropriate safety measures at the rear of the workpiece when plunge sawing. Use only
suitable saw blades (length as short as possible).
Note
Use the plunge cutting technique only on soft materials and with short saw blades. The product can
be used in one of two plunge cutting positions: in the normal position or in the reversed position.
14
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
1.
2.
3.
4.
Bring the forward edge of the AVR contact shoe into contact with the workpiece.
Disengage the transport lock.
Press the control switch.
Press the forward edge of the contact shoe against the workpiece and begin the plunge action by slowly
increasing the angle of attack.
Note
To prevent stalling, it is important that the product is running before the saw blade is brought into
contact with the surface.
5. Once the saw blade has penetrated right through the material, bring the tool into the normal working
position (contact shoe flush with the workpiece) and then continue sawing along the cutting line.
6 Care and maintenance of cordless tools
WARNING
Risk of electric shock! Attempting care and maintenance with the battery fitted in the tool can lead
to severe injury and burns.
▶
Always remove the battery before carrying out care and maintenance tasks!
Care and maintenance of the tool
• Carefully remove stubborn dirt from the tool.
• Clean the air vents carefully with a dry brush.
• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as
these may attack the plastic parts.
Care of the Li­ion batteries
• Keep the battery free from oil and grease.
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
15
•
Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as
these may attack the plastic parts.
Avoid ingress of moisture.
•
Maintenance
• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all
function correctly.
• Do not operate the cordless tool if signs of damage are found or if parts malfunction. Have the tool
repaired by Hilti Service immediately.
• After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.
6.1 Checks after care and maintenance work
After carrying out care and maintenance, check that all protective and safety devices are fitted and that
they function faultlessly.
▶
7 Transport and storage of cordless tools
Transport
CAUTION
Inadvertent starting during transport. Uncontrolled starting during transport may occur if the battery
is fitted, thereby resulting in damage to the tool.
▶
Always remove the battery before transporting the tool.
Remove the battery.
Transport the tool and batteries individually packaged.
Never transport batteries in bulk form (loose, unprotected).
Check the tool and batteries for damage before use after long periods of transport.
▶
▶
▶
▶
Storage
CAUTION
Inadvertent damage caused by defective battery. A leaking battery may damage the tool.
▶
Always remove the battery before storing the tool.
Store the tool and batteries in a place that is as cool and dry as possible.
Never store batteries in direct sunlight, on heating units or behind a window pane.
Store the tool and batteries in a place where they cannot be accessed by children or unauthorized
persons.
Check the tool and batteries for damage before use after long periods of storage.
▶
▶
▶
▶
8 Troubleshooting
If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by
yourself, please contact Hilti Service.
8.1 The reciprocating saw is not operational.
Malfunction
The LEDs indicate nothing.
Possible cause
The battery is not fully inserted.
The battery is empty.
1 LED blinks.
16
The transport lock is engaged.
Action to be taken
▶
▶
▶
The battery is discharged.
▶
The battery is too hot or too cold.
▶
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
Push the battery in until it
engages with a double click.
Charge the battery.
Disengage the transport lock.
Change the battery and charge
the empty battery.
Bring the battery to the recommended working temperature.
8.2 The reciprocating saw is operational.
Trouble or fault
The tool does not achieve full
power.
The saw blade can’t be removed from the chuck.
Possible cause
The control switch is not fully
pressed.
Action to be taken
▶
Press the control switch fully.
The battery is discharged.
▶
Stroke rate set too low.
Change the battery and charge
the empty battery.
▶
The locking sleeve is not turned as
far as it will go.
▶
Set the stroke rate regulator to
the setting recommended for
the material to be cut.
Turn the locking sleeve as far as
it will go and remove the saw
blade.
9 Disposal
WARNING
Risk of injury. Hazards presented by improper disposal.
▶
▶
▶
Improper disposal of the equipment may have the following consequences: The burning of plastic
components generates toxic fumes which may present a health hazard. Batteries may explode
if damaged or exposed to very high temperatures, causing poisoning, burns, acid burns or
environmental pollution. Careless disposal may permit unauthorized and improper use of the
equipment. This may result in serious personal injury, injury to third parties and pollution of the
environment.
Dispose of defective batteries right away. Keep them out of reach of children. Do not disassemble
or incinerate the batteries.
Batteries that have reached the end of their life must be disposed of in accordance with national
regulations or returned to Hilti.
Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The
materials must be correctly separated before they can be recycled. In many countries, your old tools,
machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative
for further information.
▶
Disposal of electric tools or appliances together with household waste is not permissible.
10 China RoHS (guideline on restriction of the use of dangerous substances)
The following link takes you to the table of dangerous substances: qr.hilti.com/r3696.
You will find a link to the RoHS table, in the form of a QR code, at the end of this document.
11 Manufacturer’s warranty
▶
Please contact your local Hilti representative if you have questions about the warranty conditions.
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
17
18
English
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
Hilti = registered trademark of Hilti Corp., Schaan
Printed: 30.05.2017 | Doc-Nr: PUB / 5071383 / 000 / 07
**
20170512
Download PDF
Similar pages