RY80935 QUICK REFERENCE GUIDE
WARNING:
This Quick Reference Guide is not a substitute for reading the operator’s manual. To reduce the risk of injury or death, user must read and understand operator’s manual before using this product. All page references refer to
the operator’s manual.
FIRST TIME ASSEMBLY
1
Install the handle (see page 8).
5
Connect your garden hose to the pressure washer
(see page 9).
STARTING THE UNIT (COLD START)
1
Add fuel (see page 10).
5
Pull starter grip and rope to start (see page 11).
USING DETERGENT
1
Pour pressure washer
­detergent in soap tank (see
page 13).
2
Install blue soap nozzle
(see page 13).
3
Squeeze trigger and wait
­approx. 5 seconds for
detergent (see page 13).
Do not use E15 or E85 fuel in this unit. It is a violation of
federal law and will damage the unit and void your warranty. Only use unleaded gasoline containing up to 10%
ethanol.
5S
Completely uncoil garden hose or remove
­completely from reel to prevent kinks.
2
Connect the spray wand to the trigger handle
(see page 8).
Use of soap nozzle will activate detergent injector at a 20:1
dilution ratio.
WARNING! Never use bleach or solvent-based detergent.
Turn water faucet on fully.
• Will void your warranty
Make sure there are no leaks.
3
If detergent injection
hose comes loose
from pressure washer,
reattach it here.
• Will damage your pump
• Will damage plants/shrubs
With no nozzle installed, squeeze the trigger
to relieve air pressure. Hold the trigger until a
steady stream of water appears.
Connect the high pressure hose to the trigger
handle (see page 8).
6
This is a 4-cycle engine. Do not mix fuel and
lubricant ­together.
6
Mix fuel stabilizer with gasoline according to
manufacturer’s directions prior to filling the
tank.
Add entire bottle of lubricant provided to the pressure washer (see page 10).
2
NOZZLE SELECTION GUIDE
Allow engine to run for several seconds, then move
choke to OFF (RUN) position (see page 11).
CHOKE LEVER
OFF (RUN)
Use the chart below to determine the correct nozzle for your job.
Turn the fuel valve to OPEN (see page 11).
HIGH PRESSURE
(NO SOAP WHEN USING THESE NOZZLES)
ON
LOW
­ RESSURE
P
(FOR SOAP OR
GENTLE RINSE)
5S
CLOSE
OPEN
4
RESTARTING THE UNIT
(HOT RESTART)
FUEL VALVE OPEN
Connect the high pressure hose to the pump
(see page 8).
3
Move choke lever to the START position
(see page 11).
1
Pull starter grip and rope to start (see page 11).
CHOKE LEVER
ON (START)
ABRASIVE
0º Red
25º Green
40º White
Blue Soap
Nozzle













GENTLE
Concrete, Brick, Masonry
Siding, Gutters, House
Fencing, Deck, Patio
Lawn Equipment, Boat, RV
 Recommended Nozzle  Use With Caution for Certain Applications
Turn the fuel valve to OFF before adding
lubricant.
Completely uncoil and straighten high pressure
hose to prevent kinks.
Set unit on flat surface so engine is level.
Remove dipstick, wipe clean, put back in hole
(but don’t screw in) and check lubricant level.
4
BEFORE STORING THE UNIT
Put on/off switch in ON position (see page 11).
1
ON/OFF
SWITCH ON
Always add Pump Protector to the unit after each use and before storing. This will significantly
improve pump life. (See page 15)
Pump Protector is available from your local retailer. For further assistance, call customer service at
1-800-860-4050.
To add, follow the instructions provided by the Pump Protector manufacturer.
PUMP
PROTECTOR
DO NOT OVERTILT THE UNIT!
If the engine does not start:
• check for enough fuel;
• may need to adjust choke position;
• try starting again.
Make the most of your purchase! Go to www.ryobitools.com
and register your new tool online. For questions about operating
or maintaining your product please call, 1-800-860-4050.
991000503
5-1-15 (REV:01)
Download PDF
Similar pages