ed200/250 “k” style lid kits, p/n 629083103te

ED200/250 “K” Style Lid Kit Installation Instructions
ED200/250 “K” STYLE LID KITS,
P/N 629083103TE
SAFETY INSTRUCTIONS
! WARNING:
Before starting installation, read and understand all safety label and warnings on the machine. Also review and
understand all safety instructions in the owners, installation and service manuals.
Failure to comply could result in serious injury, death or damage to the equipment.
QUALIFIED SERVICE PERSONNEL
!
WARNING:
Only trained and certified electrical, plumbing and refrigeration technicians should service this unit.
All wiring and plumbing must conform to national and local codes. Failure to comply could
result in serious injury, death or equipment damage.
SAFETY PRECAUTIONS
This unit has been specifically designed to provide protection against personal injury. To ensure continued
protection observe the following:
! WARNING:
Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all
power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
! CAUTION:
Always be sure to keep area around the unit clean and free of clutter.
Failure to keep this area clean may result in injury or equipment damage.
! WARNING:
All ice baffle plates and bin stats, if included or recommended in this kit, must be installed as directed in this manual or
the equipment manufacturer’s instructions.
Failure to comply could result in serious injury, death or damage to the equipment.
Revision Date: July 21, 2017
www.cornelius.com
© 2016-2017, Cornelius Inc.
-1-
Revision: B
Publication Number: 629083103TEINS
DF200/250 “K” Style Lid Kit Installation Instructions
PROCEDURE
! WARNING:
Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all
power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
Item No.
Part No.
Name
Qty.
1
620066267
Lid and Lanyard Assembly, Grey
1
2
620027305
Ice Maker Lid Assembly
1
3
620027306
Bracket
2
4
70217
#8 Screw
6
5
50904
RTV
1
6
90221
Label
1
7
629083103TEINS
Installation Instruction
1
8
620701902
Acorn Nut, 8-32 Nylon
2
9
620701901
Sealing Washer
2
10
620037003
Baffle, Ice ED2XX
1
11
621701903
#8 Nylon Washer
2
12
70100
Hex Nut 08-32
2
13
43164
Screw 08-32
2
14
620042927INS
Instruction Manual - Ice Bin Baffle Sheet 2XX
1
15
620059361
Warning Label Baffle Installation
1
1. Unpack the kit.
2. Insert the baffle assembly into the adapter kit.
3. Place two (2) sealing washers (item 9) over the studs and two (2) flat washers (item11), then fasten in place with
two (2) plastic acorn nuts (item 8).
4. Set the ice maker lid on the top of the dispenser.
5. Using the slotted holes in the lid as a template, drill four (4).140 in. diameter (9/64 in.) holes at the bottom of the
slots (see detail A). Use extreme care not to drill into the hopper. Fasten the lid to the dispenser with four (4) #8
sheet metal screws, two on each side.
6. Seal the ice maker to the top of the dispenser as follows:
A. Run beads of RTV around the opening in the lid and inside of the perimeter of the ice maker outline so
that the ice maker will set on the RTV.
B. Set the ice maker onto the lid and position it as required.
C. Wipe away the excess RTV.
7. Drill 9/64 in. diameter holes into the ice maker cabinet using the bracket as a template. Use extreme care not to
drill into any ice maker components (condenser, tubing, etc.). Secure the brackets using the screws provided.
8. Follow the ice maker manufacturers instruction to complete the installation of the ice maker including the bin thermostat if so equipped or required.
9. If the plastic acorn nuts interfere with the positioning of the plastic manual fill cover, it may be necessary to make
small notches in the back flange of the cover to clear the acorn nuts.
NOTE: Bin Thermostat must not interfere with the agitator rotation.
Publication Number: 629083103TEINS
-2-
© 2016-2017, Cornelius Inc.
ED200/250 “K” Style Lid Kit Installation Instructions
ICEMAKER
4
3
SEAL ICEMAKER TO
ITEM 5 WITH RTV
4
2
SEE DETAIL A
3
1
6
4
DETAIL "A"
ENLARGED
4
0
DRILL 9/64" (.140" ) HOLES USING
BOTTOM OF SLOTTED HOLES AS A TEMPLATE
Figure 1. Dispenser Assembly
© 2016-2017, Cornelius Inc.
-3-
Publication Number: 629083103TEINS
DF200/250 “K” Style Lid Kit Installation Instructions
2 PLACES
PLACES
2 PLACES
8
11
9
10
Figure 2. DF2XX KIT
Publication Number: 629083103TEINS
-4-
© 2016-2017, Cornelius Inc.
ED200/250 “K” Style Lid Kit Installation Instructions
8
11
9
Figure 3. DF 2XX KIT
Figure 4. Reference Sheetmetal Cover Opening Dimensions for Mounting Icemaker.
© 2016-2017, Cornelius Inc.
-5-
Publication Number: 629083103TEINS
Download PDF
Similar pages