FRICTION ADJUSTMENTS
A
Hex Key C (4mm)
Hex Key B (5mm)
Crossbar Cap
Hex Key A (8mm)
a. After prolonged use, the Ball
Joint Swivel/Tilt Mechanism
may require increased friction.
This can be achieved by
tightening the 3 Ball Joint
Friction Screws (A) using Hex
Key C.
PARA/FLEX INSTALLATION HARDWARE
Vertical Assembly Cap
Hex Key D (2mm)
Vertical Assembly
Flat Bearing
Hand Crank
EXPANDING/COLLAPSING CROSSBAR
MOUNTING OPTIONS
a. Unfold Crossbar Wings to accommodate 3 or 4 monitors per row.
Beam Mount
Beam Mount Bolt
4 Thumbscrews
Beam Mount
Slatwall Mount
2 Thumbscrews
Slatwall Mount Bolt
Slatwall Mount
Desk Mount
Para/Flex
Instructions
Desk Mount Bolt
Desk Mount
3 Desk Mount Screws
Additional hardware required: Electric drill with ½” drill bit
HSIPM00911
b. Fold away Crossbar Wings to hide behind 1 or 2 monitors.
STEP 1: ATTACH MOUNT TO WORK SURFACE
Slatwall Mount
Beam Mount
C
a. Slide Vertical Assembly (A) into
Slatwall Mount (B) as shown.
A
a. Slide Vertical Assembly (A) into
Beam Mount (B) as shown.
A
b. Fasten Slatwall Mount Bolt (C)
into the underside of Slatwall
Mount using Hex Key A.
B
b. Fasten Beam Mount Bolt (C) into
the underside of Beam Mount using
Hex Key A.
B
C
B
a. Attach Hand Crank (A), as shown.
e. Snap in provided Caps (G) to
cover large clamp screw hole (F).
F
D
c. Insert the lips on the underside of
Beam Mount (D) into the slot(s) of
systems furniture (E). Push backward
to engage.
c. Insert the lips on the backside
of Slatwall Mount (D) into the
slot(s) of systems furniture (E).
Push downward to engage.
d. Fasten using 2 Thumbscrews
(F) provided. Be sure Thumbscrews are fully engaged.
E
d. Fasten using 4 Thumbscrews (F)
provided. Be sure Thumbscrews are
fully engaged.
D
Main Height Adjustment
d. Slide Second Row Crossbar
(D) onto Second Row Posts.
Tighten all 6 Clamping Screws
(E + F).
D
C
F
c. Repeat previous steps to
attach other Second Row
Post (C).
STEP 2: ATTACH FIRST ROW CROSSBAR
E
F
a. Slide Vertical Assembly (A) into
Desk Mount (B) as shown.
A
G
a. Remove all but center monitor.
STEP 4: ATTACH VESA BRACKETS TO MONITORS
C
b. Slide First Row Crossbar (B)
onto Vertical Assembly.
B
C
c. Fasten Cap (C) to Vertical
Assembly.
B
F
c. Place Desk Mount and Vertical
Assembly on the desk surface in the
desired location.
i. Trace the 3 Mounting Holes (D)
onto the desk surface.
Remove Desk Mount and
Vertical Assembly.
D
E
a. Place VESA Bracket in position on
back of monitor with lip (A) toward
top of monitor. Attach using 4 VESA
Bracket Screws.
i. If mounting space for 75mm
VESA Bracket is inset into
back of monitor, place the 4
Plastic Spacers (B) between
VESA Bracket and monitor.
Align with hole pattern and
attach using 4 Extended VESA
Bracket Screws (C).
b. While holding Second Row
Crossbar, loosen bottom Clamping
Screws (A) slowly.
c. Lower Second Row Crossbar to
desired height.
d. Continue holding Second Row
Crossbar and tighten Clamping
Screws.
A
Note: VESA Bracket can accommodate
75mm or 100mm hole patterns. For this,
you may also use screws that came with
your monitor.
b. Fasten Desk Mount Bolt (C) into
the underside of Desk Mount using
Hex Key A.
A
Second Row Crossbar Height
Adjustment
A
a. Slide Flat Bearing (A) onto
Vertical Assembly.
b. Rotate Hand Crank to adjust
Para/Flex to desired height.
Note: When not in use, store Hand Crank
on Crank Mechanism (B) with the handle
turned away.
E
Desk Mount
ADJUSTMENT INSTRUCTIONS
e. If necessary, adjust Second Row
Posts individually:
A
i. Loosen top and bottom
Clamping Screws for one
Second Row Post and adjust
to desired height.
ii. Re-tighten Clamping Screws.
iii. Repeat with other Post if
necessary.
B
C
Lateral Monitor Adjustment
STEP 3: ATTACH SECOND ROW CROSSBAR (If Applicable)
STEP 5: ATTACH MONITORS TO PARAMOUNT
a. Push Glider Assembly (A) to
desired location.
A
A
a. Slide Second Row Post (A)
into First Row Crossbar as
shown.
d. Using an electric drill, drill three ½”
holes where Mounting Holes were
traced.
a. Slide VESA Bracket (A) into Ball
Joint (B) until it clicks.
e. Replace Desk Mount and Vertical
Assembly on the desk surface. Align
holes.
b. To remove, depress QuickRelease Tab (C) and slide monitor
up and away from Paramount.
i. Place Desk Mount Plate
(E) on the underside of
the desk and align holes.
Fasten using 3 Desk Mount
Screws (F) and Hex Key B.
c. Repeat steps for each monitor
required.
B
D
C
b. While holding the post,
tighten Clamping Screw (B)
using Hex Key B.
c. Snap in provided Caps (C) to
cover large clamp screw hole
(D).
Individual Monitor Fine Tune
Adjustment
A
C
a. Raise and lower individual monitors
by turning Adjustment Screw (A)
located under each Ball Joint.
B
Security Screw
Note: If security is required, tighten
Security Screw using Hex Key D.
b. Using Hex Key C, turn Adjustment
Screw clockwise to raise the height
of the monitor and counterclockwise
to lower the height.
Note: This can also be done with an
electric drill and 4mm Allen drill bit.
Adjustment may be easier with monitor
removed.
A
Download PDF
Similar pages