TX26D12VM0AAA - Eurocomposant

DATE : May 1st ,2012
FOR MESSRS :
CUSTOMER’S ACCEPTANCE SPECIFICATIONS
TX26D12VM0AAA
Contents
No.
ITEM
SHEET No.
PAGE
1
COVER
7B64PS 2701-TX26D12VM0AAA-3
1-1/1
2
RECORD OF REVISION
7B64PS 2702-TX26D12VM0AAA-3
2-1/2~2/2
3
GENERAL DATA
7B64PS 2703-TX26D12VM0AAA-3
3-1/1
4
ABSOLUTE MAXIMUM RATINGS
7B64PS 2704-TX26D12VM0AAA-3
4-1/1
5
ELECTRICAL CHARACTERISTICS
7B64PS 2705-TX26D12VM0AAA-3
5-1/2~2/2
6
OPTICAL CHARACTERISTICS
7B64PS 2706-TX26D12VM0AAA-3
6-1/2~2/2
7
BLOCK DIAGRAME
7B64PS 2707-TX26D12VM0AAA-3
7-1/1
8
RELIABILITY TESTS
7B64PS 2708-TX26D12VM0AAA-3
8-1/1
9
LCD INTERFACE
7B64PS 2709-TX26D12VM0AAA-3
9-1/11~11/11
10
OUTLINE DIMENSIONS
7B64PS 2710-TX26D12VM0AAA-3
10-1/2~2/2
11
APPEARANCE STANDARD
7B64PS 2711-TX26D12VM0AAA-3
11-1/3~3/3
12
PRECAUTIONS
7B64PS 2712-TX26D12VM0AAA-3
12-1/2~2/2
13
DESIGNATION OF LOT MARK
7B64PS 2713-TX26D12VM0AAA-3
13-1/1
ACCEPTED BY:
KAOHSIUNG OPTO-ELECTRONICS INC.
PROPOSED BY:
SHEET
NO.
7B64PS 2701-TX26D12VM0AAA-3
PAGE
1-1/1
2. RECORD OF REVISION
DATE
Jul.07,’09
SHEET No.
SUMMARY
7B64PS 2703TX26D12VM0AAA-2
PAGE 3-1/1
7B64PS 2705TX26D12VM0AAA-2
PAGE 5-2/2
3.1 DISPLAY FEATURES
Revised
Power Consumption 7.68W → 8.04W
5.2 BACKLIGHT CHARACTERISTICS
Revised
Item
Typ.
LED Forward Current
(660)
(Dim Control)
(30)
↓
Item
Typ.
LED Forward Current
670
(Dim Control)
30
7B64PS 2706TX26D12VM0AAA-2
PAGE 6-1/2
6. OPTICAL CHARACTERISTICS
ITEM
SYMBOL
Red
Color
Chromaticity
Green
Blue
White
CONDITION
MIN.
TYP.
MAX.
x
(0.57)
(0.61)
(0.67)
y
(0.27)
(0.36)
(0.37)
x
(0.25)
(0.37)
(0.35)
y
 =0°,
(0.54)
(0.59)
(0.64)
x
θ=0°
(0.09)
(0.15)
(0.19)
y
(0.05)
(0.10)
(0.15)
x
(0.30)
(0.35)
(0.40)
y
(0.32)
(0.37)
(0.42)
MIN.
TYP.
MAX.
x
0.56
0.61
0.66
y
0.31
0.36
0.41
x
0.32
0.37
0.42
↓
ITEM
SYMBOL
Red
Color
Chromaticity
Green
Blue
White
CONDITION
y
 =0°,
0.54
0.59
0.64
x
θ=0°
0.10
0.15
0.20
y
0.05
0.10
0.15
x
0.30
0.35
0.40
y
0.32
0.37
0.42
7B63PS 271010.1 SURFACE SIDE
TX26D12VM0AAA-2
All Sheet Revised.
PAGE 10-1/2
Nov.26,’09
7B63PS 271010.2 BACK SIDE
TX26D12VM0AAA-2
All Sheet Revised.
PAGE 10-2/2
7B64PS 27066. OPTICAL CHARACTERISTICS
TX26D12VM0AAA-3 Revised
PAGE 6-1/2
NTSC Ratio Typ. 60 → 54
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2702-TX26D12VM0AAA-3
PAGE
2-1/2
DATE
Nov.26,’09
May 01,’12
SHEET No.
SUMMARY
7B63PS 2710TX26D12VM0AAA-3
PAGE 10-1/2
7B63PS 2710TX26D12VM0AAA-3
PAGE 10-2/2
All pages
10.1 SURFACE SIDE
All Sheet Revised.
7B64PS-2704TX26D14VM2BPA-2
Page 4-1/1
7B64PS-2708TX26D14VM2BPA-2
Page 8-1/1
4. ABSOLUTE MAXIMUM RATINGS
Revised : Note2.
10.2 BACK SIDE
All Sheet Revised.
Company name changed:
KAOHSIUNG HITACHI ELECTRONICS CO.,LTD.

KAOHSIUNG OPTO-ELECTRONICS INC.
8. RELIABILITY TESTS
Added : Note4
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2702-TX26D12VM0AAA-3
PAGE
2-2/2
3. GENERAL DATA
3.1 DISPLAY FEATURES
This module is a 10.4” SVGA of 4:3 format amorphous silicon TFT.The pixel format is vertical stripe and
sub pixels are arranged as R(red), G(green), B(blue) sequentially. This display is RoHS compliant, and
COG (chip on glass) technology and LED backlight are applied on this display.
Part Name
TX26D12VM0AAA
Module Dimensions
243.0(W) mm x 185.1(H) mm x 11.0max (D) mm
LCD Active Area
211.2(W) mm x 158.4(H) mm
Dot Pitch
0.088(W) mm x 3(R, G, B)(W) x 0.264(H) mm
Resolution
800 x 3(RGB)(W) x 600(H) dots
Color Pixel Arrangement
R, G, B Vertical stripe
LCD Type
Transmissive Color TFT; Normally Black
Display Type
Active Matrix
Number of Colors
16777k Colors(8-bit RGB)
Backlight
8 LEDs parallel x 3 serial (24 LEDs in total)
Weight
560 g (typ.)
Interface
1ch-LVDS/Receiver ; 20 pins
Power Supply Voltage
3.3V for LCD; 12V for Backlight
Power Consumption
1.221 W for LCD (SVGA) ;8.04W for backlight
Viewing Direction
Super Wide Version (Horizontal and Vertical: 170°, CR  10)
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2703-TX26D12VM0AAA-3
PAGE
3-1/1
4. ABSOLUTE MAXIMUM RATINGS
Item
Symbol
Min.
Max.
Unit
Remarks
Supply Voltage
VDD
0
4.0
V
-
Input Voltage of Logic
VI
-0.3
VDD+0.3
V
Note 1
Operating Temperature
Storage Temperature
LED Unit
Top
-20
70

C
Note 2

C
Note 2
Tst
-30
80
Forward Current
IF
-
120
mA
Reverse Voltage
VR
-
3.65
V
Note 3
Note 1: It shall be applied to pixel data signal and clock signal.
Note 2: The maximum rating is defined as above based on the chamber temperature, which might be
different from ambient temperature after assembling the panel into the application. Moreover,
some temperature-related phenomenon as below needed to be noticed:
- Background color, contrast and response time would be different in temperatures other than
25  C .
- Operating under high temperature will shorten LED lifetime.
Note 3: Fig. 4.1 shows the maximum rating of LED forward current against temperature. The backlight
unit in this display has been set to 80 mA per LED. This is within the range when operating the
display between -20~70  C .
For the dimming function, reducing the LED backlight voltage 12V to the expected brightness is
recommended. Alternatively, using PWM signal with 10KHz and 3.3V amplitude to dim by
adjusting the duty ratio.
Fig. 4.1
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2704-TX26D12VM0AAA-3
PAGE
4-1/1
5. ELECTRICAL CHARACTERISTICS
5.1 LCD CHARACTERISTICS
T a  25  C , VSS  0V
Item
Symbol
Condition
Min.
Typ.
Max.
Unit
Remarks
Power Supply Voltage
Differential Input
Voltage for LVDS
Receiver Threshold
VDD
-
3.0
3.3
3.6
V
-
“H” level
-
-
+100
“L” level
-100
-
-
mV
Note 1
“H” level
0.7VDD
-
VDD
“L” level
0
-
0.3VDD
-
370
550
mA
Note 2,3
VI
DPS,FRC,AMODE
VI
Signal Input Voltage
VDD-VSS
CMOS
V
LEVEL
Power Supply Current
IDD
Vsync Frequency
-
-
60
75
Hz
Note 4,5
Hsync Frequency
fv
fH
-
-
37.7
50.6
KHz
Note 4
DCLK Frequency
f CLK
-
-
40
43
MHz
Note 4
=3.3V
Note 1: VCM=VDD / 2V
VCM is common mode voltage of LVDS transmitter / receiver. The input terminal of LVDS
transmitter is terminated with 100Ω.
IN+
LVDS
100Ω
Receiver
IN-
Note 2: fV=60Hz,fCLK=40MHz,VDD=3.3V,DC Current.
Typical value is measured when displaying vertical 256 gray scale. Maximum is measured
when displaying Vertical-stripe.
DC Ampere Meter
TFT-LCM
IDD
VDD
VDD
VSS
Note 3: As this module contains 0.8A fuse, prepare current source that is enough for cutting current
fuse when a truble happens. (larger than 2.0A)
Note 4: For LVDS Transmitter Input
Note 5: Vertical Frequency is encouraged to be used by 60Hz. The flicker level changes by the gap of
the vertical frequency.
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2705-TX26D12VM0AAA-3
PAGE
5-1/2
5.2 BACKLIGHT CHARACTERISTICS
Item
Symbol
Condition
Min.
Typ.
Max.
Unit
Remarks
LED Input Voltage
VLED
-
11.7
12.0
12.3
V
Note1
LED Forward Current
(Dim Control)
ILED
0V; 0% duty
-
670
-
3.3VDC; 100% duty
-
30
-
mA
Note 2
LED lifetime
-
640 mA
-
70K
-
hrs
Note 3
Note 1: As Fig. 5.1 shown, LED current is constant, 640 mA, controlled by the LED driver when
applying 12V VLED.
Note 2: Dimming function can be obtained by applying DC voltage or PWM signal from the display
interface CN1. The recommended PWM signal is 1K ~ 10K Hz with 3.3V amplitude.
Note 3: The estimated lifetime is specified as the time to reduce 50% brightness by applying 640 mA at
25  C .
640mA
560
mA
DIM (CN1:Pin 3)
20)
+
1) DC voltage 0 V to 3.3 VDC
2) PWM duty 0% to 100%
LED
Driver
12V
-
Fig. 5.1
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2705-TX26D12VM0AAA-3
PAGE
5-2/2
6. OPTICAL CHARACTERISTICS
The optical characteristics are measured based on the conditions as below:
- Supplying the signals and voltages defined in the section of electrical characteristics.
- The backlight unit needs to be turned on for 30 minutes.
- The ambient temperature is 25  C .
- In the dark room around 500~1000 lx, the equipment has been set for the measurements as shown in
Fig 6.1.
Ta  25 C , f v  60 Hz, VDD  3.3V
Item
Condition
Symbol
Brightness of White
-
Brightness Uniformity
-
Contrast Ratio
CR
Response Time
NTSC Ratio
Viewing Angle
Red
Green
ILED= 640 mA
Max.
-
cd/m
75
-
-
%
Note 2
800
-
-
Note 3
-
25
65
ms
Note 4
-
60
-
%
-
Degree
Note 5
-
Note 6
-
  0 ,  0
x
  0 , CR  10
-
85
-
 x
  180  , CR  10
-
85
-
y
  90 , CR  10
-
85
-
 y
  270  , CR  10
-
85
-
X
0.56
0.61
0.66
Y
0.31
0.36
0.41
X
0.32
0.37
0.42
0.54
0.59
0.64
0.10
0.15
0.20
Y
0.05
0.10
0.15
X
0.30
0.35
0.40
Y
0.32
0.37
0.42
Chromaticity
X


  0 ,  0
Note 1
500


Remarks
2
450
  0 ,  0

Unit
350
Rise + Fall
Y
White
  0 ,  0 ,
Typ.

Color
Blue
Min.
Note 1: The brightness is measured from 9 point of the panel, P1~P9 in Fig. 6.2, for the average value.
Note 2: The brightness uniformity is calculated by the equation as below:
Brightness uniformity =
Min. Brightness
Max. Brightness
X100%
, which is based on the brightness values of the 9 points measured by BM-5 as shown in Fig. 6.2.
Photo detector:BM-5A
Field 1∘
Distance:500 mm
Dot(0,0)
X=150
P1
P2
P3
X=300
P4
P5
P6
P7
P8
P9
X=450
LCD panel
Y=600 Y=1200 Y=1800
Fig. 6.1
Fig. 6.2
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2706-TX26D12VM0AAA-3
PAGE
6-1/2
Note 3: The Contrast ratio is measured from the center point of the panel, P5, and defined as the
following equation:
Brightness of White
CR =
Brightness of Black
Note 4: The definition of response time is shown in Fig. 6.3. The rising time is the period from 10%
brightness to 90% brightness when the data is from white to black. Oppositely, Falling time is
the period from 90% brightness rising to 10% brightness.
Black
Brightness
100 %
90
White
Falling time
Rising time
Tr
10
0
Black
Tf
0
Fig . 6.3
Note 5: The definition of viewing angle is shown in Fig. 6.4. Angle  is used to represent viewing
directions, for instance,   270  means 6 o’clock, and   0  means 3 o’clock. Moreover, angle
 is used to represent viewing angles from axis Z toward plane XY.
z
 = Viewing angle
  90
y
12 o'clock

 (x, y ,0)

x  0
3 o'clock
x'
  180
9 o'clock
z'
y'   270
6 o'clock
Fig. 6.4
Note 6: The color chromaticity is measured from the center point of the panel, P5, as shown in Fig. 6.2.
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2706-TX26D12VM0AAA-3
PAGE
6-2/2
8. RELIABILITY TESTS
Test Item
Condition
High Temperature
1) Operating
2) 70  C
240 hrs
Low Temperature
1) Operating
2) -20  C
240 hrs
High Temperature
1) Storage
2) 80  C
240 hrs
Low Temperature
1) Storage
2) -30  C
240 hrs
Heat Cycle
1) Operating
2) –20  C ~70  C
3) 3hrs~1hr~3hrs
240 hrs
Thermal Shock
1) Non-Operating
2) -35  C  85  C
3) 0.5 hr  0.5 hr
240 hrs
High Temperature &
Humidity
1) Operating
2) 40  C & 85%RH
3) Without condensation
(Note3)
240 hrs
Vibration
1) Non-Operating
2) 20~200 Hz
3) 2G
4) X, Y, and Z directions
1 hr for each direction
1) Non-Operating
2) 10 ms
3) 50G
4)  X,  Y and  Z directions
Once for each direction
Mechanical Shock
ESD
1) Operating
2) Tip: 200 pF, 250 
3) Air discharge for glass:  8KV
4) Contact discharge for metal frame:  8KV
1) Glass: 9 points
2) Metal frame: 8 points
(Note4)
Note 1: Display functionalities are inspected under the conditions defined in the specification after the
reliability tests.
Note 2: The display is not guaranteed for use in corrosive gas environments.
Note 3: Under the condition of high temperature & humidity, if the temperature is higher than 40℃, the
humidity needs to be reduced as Fig. 8.1 shown.
Note 4: All pins of LCD interface (CN1) have been tested by  100V contact discharge of ESD under
non-operating condition.
90
80
70
60
50
40
30
20
10
0
20 25
KAOHSIUNG OPTO-ELECTRONICS INC.
30 35
40 45 50 55 60
Temperature Ta (  C)
Fig. 8.1
SHEET
NO.
65
70
75
7B64PS 2708-TX26D12VM0AAA-3
PAGE
8-1/1
9. LCD INTERFACE
9.1 INTERFACE PIN CONNECTIONS
The display interface connector is FI-SEB20P-HF13E made by JAE and more details of the connector are shown
in the section of outline dimension.
Pin assignment of LCD interface is as below:
Pin No.
1
2
3
4
5
6
7
8
9
Symbol
VDD
VDD
DPS
VSS
IN0IN0+
VSS
IN1IN1+
10
VSS
11
IN2-
12
IN2+
13
VSS
14
CLK IN-
15
CLK IN+
16
17
18
19
FRC
IN3IN3+
AMODE
20
DIM
Description
REMARKS
Power Supply for Logic
Note1
Scan Direction Control (High : Reverse , Low : STD)
Ground (0V)
Note3
Note2
Pixel Data
Ground (0V)
Note2
Pixel Data
Ground (0V)
Note2
Pixel Data
Ground (0V)
Note2
Clock
High : 8bit , Low : 6bit
Pixel Data
LVDS Format Setting (Refer to P9-2/11)
Normal Brightness:0V or 0% PWM Duty
Brightness Control:0V to 3.3VDC or 0% to 100% PWM
Duty.
Note 1: All VDD pins should be connected to +3.3V.
Note 2: All VSS pins should be connected to GND(0V),Metal bezel is connected internally to VSS.
Note 3: Vertical Display Inode and Horizontal Display mode control
DPS : Low
DPS : High
The backlight interface connector is SM08B-SRSS-TB made by JST, and pin assignment of backlight is as below:
Pin No.
Signal
Level
1~3
VLED+
-
Power Supply for LED(12V)
4~5
NC
-
No Connection
6~8
VLED-
-
GND
KAOHSIUNG OPTO-ELECTRONICS INC.
Function
SHEET
NO.
7B64PS 2709-TX26D12VM0AAA-3
PAGE
9-1/11
9.2 LVDS INTERFACE
Note 1: LVDS cable impedance should be 100 ohms per signal line when each
2-lines(+,-) is used in differential mode.
Note 2: Transmitter Made by Thine : THC63LVDM83R equivalent.
Transmitter is not contained in Module.
Note 3: Receiver : with built-in TCON IC.
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2709-TX26D12VM0AAA-3
PAGE
9-2/11
9.3 DATA MAPPING
1) 8 Bit Mode
Note : Assignment in the Mode A(THC63LVDM83R)
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2709-TX26D12VM0AAA-3
PAGE
9-3/11
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2709-TX26D12VM0AAA-3
PAGE
9-4/11
2) 6 Bit Mode
Note : Assignment in the Mode A(THC63LVDM83R)
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2709-TX26D12VM0AAA-3
PAGE
9-5/11
* Connection circuit of IN3-, IN3+ for 6 bit mode
① Connect TD0~TD5 to GND
② Connect IN3+ to 3.3V with 820Ω, and connect IN3- to GND with 470Ω as below circuit.
Note 1: The impedance between differential signal pair should be 100 Ω.
Note 2: Transmitter is not contained in module.
The recommended transmitter is Thine THC63LVDM83R or equivalent.
Note 3: The built in receiver is Thine THC63LVDF84B.
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2709-TX26D12VM0AAA-3
PAGE
9-6/11
9.4 DATA INPUT for DISPLAY COLOR(8BIT MODE)
Red
Input
R7
color
R6
R5
R4
Data
R3
Green
R2
R1
MSB
R0
G7
G6
G5
G4
Data
G3
Blue
G2
G1
LSB MSB
G0
B7
B6
B5
B4
Data
B3
B2
B1
LSB MSB
B0
LSB
Black
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Red(255)
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Green(255)
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
Basic
Blue(255)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
Color
Cyan
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Magenta
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
Yellow
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
White
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Black
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Red(1)
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Red(2)
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Red(253)
1
1
1
1
1
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Red(254)
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Red(255)
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Black
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Green(1)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
Green(2)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Green(253)
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
1
0
0
0
0
0
0
0
0
Green(254)
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
Green(255)
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
Black
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Blue(1)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
Blue(2)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Blue(253)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
1
Blue(254)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
0
Blue(255)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
Red
Green
Blue
Note 1: Definition of gray scale : Color(n) Number in parenthesis indicates gray scale level. Larger
number corresponds to brighter level.
Note 2: Data Signal : 1 : High, 0 : Low
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2709-TX26D12VM0AAA-3
PAGE
9-7/11
(6BIT MODE)
Red
Input
Data
Green
Data
Blue
Data
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
color
MSB
LSB MSB
LSB MSB
LSB
Black
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Red(63)
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
Green(63) 0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
Basic
Blue(63)
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
Color
Cyan
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
Magenta
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
1
1
1
Yellow
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
White
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Black
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Red(1)
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
Red(2)
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Red(61)
1
1
1
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
Red(62)
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
Red(63)
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
Black
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Green(1)
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
Green(2)
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Green(61) 0
0
0
0
0
0
1
1
1
1
0
1
0
0
0
0
0
0
Green(62) 0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
Green(63) 0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
Red
Green
Blue
Black
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Blue(1)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
Blue(2)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Blue(61)
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
1
Blue(62)
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
Blue(63)
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
Note 1: Definition of gray scale : Color(n) Number in parenthesis indicates gray scale level. Larger
number corresponds to brighter level.
Note 2: Data Signal : 1 : High, 0 : Low
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2709-TX26D12VM0AAA-3
PAGE
9-8/11
9.5 INTERFACE TIMING
(1) LVDS Receiver Timing
(Interface of TFT module)
Item
Symbol
Min.
Typ.
Max.
Unit
MHz
DCLK
FREQUENCY
1/tcLK
35
40
45
RinX
0 data position
tRP0
1/7*tCLK –0.49
1/7*tCLK
1/7*tCLK +0.49
(X=0,1,2)
1st data position
tRP1
-0.49
0
+0.49
2nd data position
tRP2
6/7*tCLK –0.49
6/7*tCLK
6/7*tCLK +0.49
3rd data position
tRP3
5/7*tCLK –0.49
5/7*tCLK
5/7*tCLK +0.49
4th data position
tRP4
4/7*tCLK –0.49
4/7*tCLK
4/7*tCLK +0.49
5th data position
tRP5
3/7*tCLK –0.49
3/7*tCLK
3/7*tCLK +0.49
6th data position
tRP6
2/7*tCLK –0.49
2/7*tCLK
2/7*tCLK +0.49
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2709-TX26D12VM0AAA-3
Note
ns
PAGE
9-9/11
(2) Timing converter timing
(Input timing for transmitter)
The timings except mentiond above are referd to the specifications of your transmitter.
Item
DCLK
DTMG
Symbol
Min.
Typ.
Max.
Unit
tCLK
22.2
25.0
28.5
ns
Horizontal Cycle
tH
850
1060
1600
Horizontal Valid Data width
tHD
800
800
800
Vertical Cycle
tv
603
628
1000
Vertical Valid Data width
tVD
600
600
600
Cycle time
tCLK
tH
Note 1: It counts by a typical value of line cycle time.
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2709-TX26D12VM0AAA-3
PAGE
9-10/11
(3) TIMING BETWEEN INTERFACE SIGNAL AND POWER SUPPLY
Power Supply, Input Signal and Backlight Voltage ON/OFF/REENTRY should comply with the following
sequence.
Note 1: In order to prevent electronic parts from destruction caused by latch-up, please input signal
after Power Supply Voltage ON. In addition, please turn off signals before power supply
voltage OFF.
Note 2: In order to prevent from function error due to residual charge, please reenter power supply
voltage after time stipulated with t7.
Note 3: Please turn on Backlight after signals fix and turn off before signals down, otherwise noise
appears in the display. The noise cause no problem with display performance in case of timing
sequence comply with the spec.
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2709-TX26D12VM0AAA-3
PAGE
9-11/11
11. APPEARANCE STANDARD
The appearance inspection is performed in a dark room around 1200 lx based on the conditions as
below:
- The distance between inspector’s eyes and display is 30 cm.
- The viewing zone is defined with angle  shown in Fig. 11.1 The inspection should be performed
within 45∘when display is shut down. The inspection should be performed within 5∘when display is
power on.


Fig. 11.1
11.1 THE DEFINITION OF LCD ZONE
LCD panel is divided into 3 areas as shown in Fig.11.2 for appearance specification in next section. A
zone is the LCD active area (dot area); B zone is the area, which extended 1 mm out from LCD active
area; C zone is the area between B zone and metal frame.
In terms of housing design, B zone is the recommended window area customers’ housing should be
located in.
Metal frame
1 mm
A zone
B zone
C zone
Fig. 11.2
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2711-TX26D12VM0AAA-3
PAGE
11-1/3
11.2 LCD APPEARANCE SPECIFICATION
The specification as below is defined as the amount of unexpected phenomenon or material in different
zones of LCD panel. The definitions of length, width and average diameter using in the table are shown
in Fig. 11.3 and Fig. 11.4.
Item
Criteria
Length (mm)
Ignored
L≦40
L≦20
Width (mm)
Maximum number Minimum space
W≦0.02
Ignored
Scratches
0.02<W≦0.04
10
W≦0.04
10
Dent
Serious one is not allowed
Wrinkles in polarizer
Serious one is not allowed
Average diameter (mm)
Maximum number
D≦0.3
Ignored
Bubbles on polarizer
0.3<D≦0.5
10
0.5<D≦1.0
5
1.0<D
none
Filamentous (Line shape)
Length (mm)
Width (mm)
Maximum number
L : Ignored
W≦0.06
Ignored
L≦1.0
Ignored
0.06<W
1.0<L
(See Dot shape)
1) Stains
2) Foreign Materials
Round (Dot shape)
3) Dark Spot
Average diameter (mm)
Maximum number
Minimum Space
D≦0.45
Ignored
0.45<D≦0.7
5
0.7<D
none
Those wiped out easily are acceptable
Type
Maximum number
1 dot
4
Bright dot-defect
2 dot
2
In total
6
Dot-Defect
(Note 1)
1 dot
5
Dark dot-defect
2 dot
2
In total
5
In total
11
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2711-TX26D12VM0AAA-3
Applied zone
A,B
A
A
A
A,B
A,B
A
PAGE
11-2/3
a
Width
a+b
2
Average diameter =
b
Length
Fig 11.3
Fig 11.4
Note 1: The definitions of dot defect are as below:
- The defect area of the dot must be bigger than half of a dot.
- For bright dot-defect, showing black pattern, the dot’s brightness must be over 30% brighter
than others.
- For dark dot-defect, showing white pattern, the dot’s brightness must be under 70% darker
than others.
- The definition of 1-dot-defect is the defect-dot, which is isolated and no adjacent defect-dot.
- The definition of adjacent dot is shown as Fig. 11.5.
- The Density of dot defect is defined in the area within diameter  =20mm.
The dots colored gray are
adjacent to defect-dot A.
A
Fig. 11.5
Fig 11.5
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2711-TX26D12VM0AAA-3
PAGE
11-3/3
12. PRECAUTIONS
12.1 PRECAUTIONS of ESD
1) Before handling the display, please ensure your body has been connected to ground to avoid any
damages by ESD. Also, do not touch display’s interface directly when assembling.
1) Please remove the protection film very slowly before turning on the display to avoid generating ESD.
12.2 PRECAUTIONS of HANDLING
1) In order to keep the appearance of display in good condition, please do not rub any surfaces of the
displays by sharp tools harder than 3H, especially touch panel, metal frame and polarizer.
2) Please do not pile the displays in order to avoid any scars leaving on the display. In order to avoid
any injuries, please pay more attention for the edges of glasses and metal frame, and wear finger
cots to protect yourself and the display before working on it.
2) Touching the display area or the terminal pins with bare hand is prohibited. This is because it will
stain the display area and cause poor insulation between terminal pins, and might affect display’s
electrical characteristics furthermore.
3) Do not use any harmful chemicals such as acetone, toluene, and isopropyl alcohol to clean display’s
surfaces.
4) Please use soft cloth or absorbent cotton with ethanol to clean the display by gently wiping. Moreover, when
wiping the display, please wipe it by horizontal or vertical direction instead of circling to prevent leaving scars
on the display’s surface, especially polarizer.
5) Please wipe any unknown liquids immediately such as saliva, water or dew on the display to avoid
color fading or any permanently damages.
6) Maximum pressure to the surface of the display must be less than 1,96 x 10 4 Pa. If the area of
adding pressure is less than 1 cm 2 , the maximum pressure must be less than 1.96N.
12.3 PRECAUTIONS OF OPERATING
1) Please input signals and voltages to the displays according to the values defined in the section of
electrical characteristics to obtain the best performance. Any voltages over than absolute maximum
rating will cause permanent damages to this display. Also, any timing of the signals out of this
specification would cause unexpected performance.
2) When the display is operating at significant low temperature, the response time will be slower than it
at 25 C  . In high temperature, the color will be slightly dark and blue compared to original pattern.
However, these are temperature-related phenomenon of LCD and it will not cause permanent
damages to the display when used within the operating temperature.
3) The use of screen saver or sleep mode is recommended when static images are likely for long
periods of time. This is to avoid the possibility of image sticking.
4) Spike noise can cause malfunction of the circuit. The recommended limitation of spike noise is no
bigger than  100 mV.
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2712-TX26D12VM0AAA-3
PAGE
12-1/2
12.4 PRECAUTIONS of STORAGE
If the displays are going to be stored for years, please be aware the following notices.
1) Please store the displays in a dark room to avoid any damages from sunlight and other sources of
UV light.
2) The recommended long term storage temperature is between 10 C  ~35 C  and 55%~75% humidity
to avoid causing bubbles between polarizer and LCD glasses, and polarizer peeling from LCD
glasses.
3) It would be better to keep the displays in the container, which is shipped from KOE, and do not
unpack it.
4) Please do not stick any labels on the display surface for a long time, especially on the polarizer.
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2712-TX26D12VM0AAA-3
PAGE
12-2/2
13. DESIGNATION of LOT MARK
1) The lot mark is showing in Fig.13.1. First 4 digits are used to represent production lot, T represented
made in Taiwan, and the last 6 digits are the serial number.
9
0
5
1
T
0
0
0
0
0
1
Serial number
T : Made in Taiwan
Week
Month
Year
2) The tables as below are showing what the first 4 digits of lot mark are shorted for.
Year
Mark
Month
Mark
Month
Mark
Week (Days)
Mark
2014
9
1
01
7
07
1~7
1
2015
0
2
02
8
08
8~14
2
2016
1
3
03
9
09
15~21
3
2017
2
4
04
10
10
22~28
4
2018
3
5
05
11
11
29~31
5
6
06
12
12
3) Except letters I and O, revision number will be showen on lot mark and following letters A to Z.
4) The location of the lot mark is on the back of the display shown in Fig. 13.1.
Fig 13.1
KAOHSIUNG OPTO-ELECTRONICS INC.
SHEET
NO.
7B64PS 2713-TX26D12VM0AAA-3
PAGE
13-1/1
Download PDF
Similar pages