PIT-LED Installation.cdr:CorelDRAW

tenpintec.com
Installation Instructions for
PIT-LED
tenpintec
RGB
RED GREEN BLUE WHITE FULL COLOUR FULL DMX CONTROL
Fully controllable LED lighting for pin illumination on Pinspotter and Pinsetter machines
WHITE, RED, GREEN and BLUE LEDs on each lane
can be individually controlled by DMX512 to give
any colour of the rainbow.
Each lane pair requires one PIT-LED set,
which consists of one control box and two LED arrays
(plus cables).
Colour effects can be isolated to one lane, a block
or the entire house.
The DMX Master Controller (there are many types
available) is normally located at the main control desk.
This connects to the first PIT-LED control box (normally
lanes 1+2) by a DMX cable. The remainder of the
PIT-LED control boxes (for lanes 3+4, 5+6 etc) are
connected in a “daisy-chain” style to each other as
shown in the diagrams.
Colour effects can be static or dynamic (colour
changing). When using a PC based DMX Master
Controller, an almost endless number of
pre-programmed effects can be initiated by the
click of a mouse.
Top Socket = DMX IN
Bottom Socket = DMX OUT
DMX link cable to next
PIT-LED Control Box
(Lanes 3+4 in this example)
DMX cable from
Master Controller
at main desk
PIT-LED
RGB
Standard power outlet
115 to 240VAC
PIT-LED RGB Control Box
mounted on curtain wall
(Lanes 1+2 in this example)
Mounting brackets
for Brunswick GS Series
machines shown
Connector Cable
Connector Cable
Lane 1
Lane 2
PIT-LED Array may also be
mounted on Mask Unit
These components are supplied
in the standard PIT-LED RGB kit:
Mounting brackets
for AMF and
Brunswick A and A2
machines shown
Important saftey point:
Connector Cables from
PIT-LED Control Box to
Arrays carry only 20VDC
maximum
PIT-LED RGB Array
mounted on Pinspotter
or Pinsetter in place of
original Fluorescent pit light.
(AMF mounting shown)
The PIT-LED system is completely independent
of the Pinspotter or Pinsetter machine and
scoring system.
This makes it compatable with all machines
and systems.
1 x PIT-LED RGB Control Box
2 x PIT-LED RGB Array
2 x sets of mounting brackets and hardware
2 x PIT-LED Connector Cable
1 x IEC Power Cable
1 x DMX Cable 4m
Other components required:
DMX Master Controller, such as
DMX Control Desk (many types available)
or
USB-DMX Controller (for PC) and
DMX Software for PC
manufactured by
CS
Cybernetic Solutions Pty Ltd
www.cybernetic.com.au
86 Barry Street
Reservoir
Victoria 3073
Australia
Phone 61 3 9460 2559
Fax 61 3 9460 7071
Installation Instructions for
PIT-LED
tenpintec.com
tenpintec
RGB
RED GREEN BLUE WHITE FULL COLOUR FULL DMX CONTROL
PAGE 2
Schematic Diagram of PIT-LED system installed in a bowling centre
DMX DESK
CONTROLLER
COMPUTER
USB-DMX
Controller
Use Windows software
such as DMXControl
A programmable desk
is preferable
OR
The computer can be dedicated solely to running
the DMX system, which could include the Cosmic
lighting effects as well as the PIT-LED system.
Or an existing desk computer can be used, provided
that is powerful enough and has sufficient memory.
Running a large number of DMX scenes at one
time can be very resource intensive.
To DMX Master
Controller at
main desk
Pinspotter/Pinsetter machines omitted from drawing for clarity.
The PIT-LED Arrays can be mounted on the machines or on the mask units.
NEXT
8
7
PIT-LED
RGB
6
5
PIT-LED
RGB
4
3
PIT-LED
RGB
1
2
PIT-LED
RGB
INSTALLATION STEPS:
1. Check the voltage selector switch on the under side of the PIT-LED
Control Box and ensure it shows the correct voltage for your area 115 or 230V. Move the slider switch if necessary to select the correct
voltage.
2. Attach PIT-LED Control Box securely to curtain wall. Take care to
position the Control Box so that the power supply cable and Connector
Cables will easily reach their destinations as shown in the diagrams.
3. Remove existing fluorescent pit or pindeck light fixtures.
4. Mount PIT-LED Arrays onto Pinspotter or Pinsetter (or in some
circumstances it may be preferred to mount the PIT-LED Arrays onto
the back of the mask units) using the supplied adjustable brackets.
Tighten all bolts except the two on each bracket that allow tilt adjustment.
Leave these bolts finger tight to allow for later adjustment.
8. Plug the power cable into the socket on the bottom right side of the
Control Box and also plug it into the wall socket.
9. Re-check all connections, cable routing and voltage selector switch.
If all is well, turn on the switch at the power outlet.
10. The PIT-LED will do nothing until a command is issued from the DMX
Master Controller.
11. Using the DMX Master Controller, call up a scene or directly access
the particular DMX channels to test each PIT-LED Array. A section of the
DMX chart can be found on page 3.
12. When the PIT-LED Array is illuminated, adjust the tilt of the Array to
get the best lighting effect and then tighten the two screws on each
bracket that were left finger tight from step 4.
5. Install Connector Cables - one end to Control Box and the other end
to the PIT-LED Array. These cables are directional and will only connect
one way. Take great care that the cables are secure at both ends
and that they are routed in such a manner that they will not be fouled
by moving machine parts or any other thing.
13. Repeat steps 1 to 12 for each PIT-LED set to be installed.
6. Connect the female end of the 3 pin DMX cable from the DMX Master
Controller (either a PC or desk controller) to the DMX IN socket on the
upper left side of the PIT-LED Control Box.
15. Repeat the procedure in step 13 for all of the PIT-LEDControl Boxes
until the last Control Box is reached. Plug the supplied DMX terminator
into the DMX OUT socket of the last Control Box.
14. Connect a 3 pin DMX cable from the DMX-OUT (female) socket
on the first PIT-LED Control Box to the DMX-IN (male) socket on the
second PIT-LED Control Box.
7. Remove the front cover of the PIT-LED Control Box and set the DMX channel 16. Further non PIT-LED DMX devices may be plugged into the DMX OUT
DIP switches according to the explanationand allocation tables on
socket in a continuation of the DMX daisy-chain. In this case, the DMX
page 3. Replace and secure the front cover.
terminator should be plugged into the DMX OUT scocket of the final
device in the line.
7. Plug the power cable into the bottom right side of the Control Box
and also plug it into the wall socket.
Installation Instructions for
PIT-LED
tenpintec.com
tenpintec
RGB
RED GREEN BLUE WHITE FULL COLOUR FULL DMX CONTROL
PAGE 3
PIT-LED RGB Control Box
View of sockets
from outside
Control Box
DMX IN
MALE XLR
1
Link cable from previous
PIT-LED Control Box
or
Link Cable from DMX
Master Controller if this
unit is the first in line
2
3
1
2
3
2
DMX OUT
Link cable to DMX IN of
next PIT-LED Control Box
DMX
IN
80mm FAN
DMX
1 - GND
2 - DMX 3 - DMX +
3
2
1
6
5
4
9
8
7
3
Output Cable
to LED Array
ODD Lane
1
2
1
6
5
4
9
8
7
Output Cable
to LED Array
EVEN Lane
3
DMX
FEMALE XLR OUT
+
-
+
1=W
-
+
-
+
3=G
2=R
-
+
4=B
-
+
1=W
-
2=R
DMX DIMMER BOARD 1
+
-
3=G
+
-
DIP Switches
DMX Dimmer board 1
is set to #1
4=B
DMX DIMMER BOARD 2
(first of its 5 channels is 1)
+
-
+
OFF
ON
DMX IN
1 2 3 4 5 6 7 8 9 10
-
OFF
ON
DMX IN
DMX Dimmer Board 2
is set to #6
1 2 3 4 5 6 7 8 9 10
(first of its 5 channels is 6)l
This means that this
Control Box is set for
Lanes 1 and 2
Power Supply
Input 115 - 240VAC
Output 15-19VDC
GND
115 to 240VAC
VOLTAGE SWITCH
115-230
DMX512
Each PIT-LED RGB Control Box
is assigned 10 DMX channels,
5 for each of the two
internal DMX Dimmer Boards.
On each of the dimmer boards,
1st channel is WHITE
2nd channel is RED
3rd channel is GREEN
4th channel is BLUE
5th channel is SPARE
Setting the DIP switches
on the DMX Dimmer boards
In the diagram above,
the DIP switches are set for
lanes 1 and 2.
The DIP switches are binary
and DOWN is ON:
Switch 1 = 1
Switch 2 = 2
Switch 3 = 4
Switch 4 = 8
Switch 5 = 16
Switch 6 = 32
Switch 7 = 64
Switch 8 = 128
Switch 9 = 256
Switch 10 is not used for addressing
IMPORTANT
Switch to appropriate input voltage
DIP Switch settings
SET START
CHANNEL
SWITCH ON
Lanes 1+2
DMX Dimmer Board 1
DMX Dimmer Board 2
=
=
1
6
1
2+3
Lanes 3+4
DMX Dimmer Board 1
DMX Dimmer Board 2
=
=
11
16
1+2+4
5
Lanes 5+6
DMX Dimmer Board 1
DMX Dimmer Board 2
=
=
21
26
1+3+5
2+4+5
Lanes 7+8
DMX Dimmer Board 1
DMX Dimmer Board 2
=
=
31
36
1+2+3+4+5+6
3+6
Lanes 9+10
DMX Dimmer Board 1
DMX Dimmer Board 2
=
=
41
46
1+4+6
2+3+4+6
Lanes 11+12
DMX Dimmer Board 1
DMX Dimmer Board 2
=
=
51
56
1+2+5+6
4+5+6
etc
DMX Channel assignments:
Control Box 1
Odd lane WHITE = 1
Odd lane RED = 2
Odd lane GREEN = 3
Odd lane Blue = 4
Odd lane SPARE = 5
Even lane WHITE = 6
Even lane RED = 7
Even lane GREEN = 8
Even lane BLUE = 9
Even lane SPARE = 10
Control Box 2
Odd lane WHITE = 11
Odd lane RED = 12
Odd lane GREEN = 13
Odd lane BLUE = 14
Odd lane SPARE = 15
Even lane WHITE = 16
Even lane RED = 17
Even lane GREEN = 18
Even lane BLUE = 19
Even lane SPARE = 20
Control Box 3
Odd lane WHITE = 21
Odd lane RED = 22
etc
DIMMER BOARD 1
DIMMER BOARD 2
DIMMER BOARD 1
DIMMER BOARD 2
Installation Instructions for
PIT-LED
RGB
RED GREEN BLUE WHITE FULL COLOUR FULL DMX CONTROL
Mounting brackets for Brunswick GS Series machines
tenpintec.com
tenpintec
PAGE 4
Download PDF
Similar pages