RM75
P R O D U C T
Miniature “Mini”
RING LIGHT
M U LT I - D R I V E TM
D A T A
S H E E T
Cable Length: 15.2 cm (6”)
Four T-slots for Mounting
Aluminum Housing
Optional Camera Adapter
High Intensity LEDs
5-Pin M12 Connector
Warranty
10
YEAR
Compliant
Compliant
62471
RoHS
IEC
CE
Rated
IP
50
Connector
5-PIN
M12
PR ODUCT HI G HL I GH T S
Built-in M ulti-Dr ive TM allows the light to wor k in continuous operation or O verDr ive TM mode
Built-in dr iver, no ex ter nal wir ing needed
PNP an d NPN strobe input
O ver- cur rent protec tion
5-pin M12 quick connec t
Rev. 2.1.5
s m ar t vi s i on li g ht s. co m
PRODUCT SPECIFICATIONS
CONTINUOUS OPERATION
Electrical Input
Input Current
Wattage
PNP Line
NPN Line
OVERDRIVETM STROBE MODE
OverDriveTM Strobe Mode
24 V DC +/- 5%
Max. 2.5 A
Max. 63 W
4 mA @ 4 V DC | 10 mA @ 12 V DC | 20 mA @24 V DC
15 mA @ Ground (0 V DC)
Connect pin 5 to GND
Not applicable
Strobe Duration
Duty Cycle
Not applicable
Not applicable
Strobe Input
Not applicable
Max. 290 mA
Max. 7.0 W
(see Wiring Configuration for more information)
Max. 50 ms
Max. 10%
PNP: +4 V DC or greater to activate
NPN: GND (<1 V DC) to activate
NPN can be tied to ground OR PNP can be
Not applicable
tied to 24 V DC (not both)
PNP: +4 V DC or greater to activate
Not applicable
NPN: GND (<1 V DC) to activate
5-pin M12 connector
-18º–50º C (0º–122º F)
IP50
134g
A separate power supply for OverDriveTM mode (high-pulse operation) is recommended. (see Input Current for value)
CE, RoHS, IEC 62471
Continuous Operation Mode
On/Off Input
Connection
Ambient Temperature
IP Rating
Weight
Power Supply
Compliances
WIRING CONFIGURATION
CONTINUOUS OPERATION MODE
Pins
Function
Signal
Wire Color
1
Power In
+24VDC
BROWN
2
NPN
Sinking Signal
WHITE
3
GND
Ground
BLUE
4
PNP
Sourcing Signal
BLACK
5
Intensity Control
1-10 V DC
GREY*
For the light to function properly, apply either a PNP or NPN
signal, not both.
Failure to supply light with correct input current will result in
non-repeatable lighting
(see Product Specifications for requirements)
* Some cables use green/yellow for pin 5
For maximum intensity, it is possible to tie pin 5 to pin 1 at +24 V DC.
For continuous mode: PNP (pin 4) can be tied to +24 V DC (pin 1) or NPN (pin 2) can be tied to Ground (pin 3).
Pin layout for light (male connector)
OVERDRIVETM OPERATION MODE
Pins
Function
Signal
Wire Color
1
Power In
+24VDC
BROWN
2
NPN
Sinking Signal
WHITE
non-repeatable lighting
3
GND
Ground
BLUE
(see Product Specifications for requirements)
4
PNP
Sourcing Signal
BLACK
5
OverDriveTM Signal
Ground
GREY*
Failure to supply light with correct input current will result in
* Some cables use green/yellow for pin 5
Pin layout for light (male connector)
R E S O U R C E CO RN E R
Ad d i ti o n al reso urces are availab le o n o ur web si te, inc ludi ng C A D files,
v i d e o s, and ap p li c at io n ex am p les.
Sm ar t Vi s i o n L i g ht s
2 3 5 9 H o lto n R o ad
M u s k e g on, M I 49445
P: + 1 2 3 1.722.1199 | F: + 1 231.722.9922
s mar t vi s io nlig hts. co m
te ch s u p p o r t @ sm ar t vi si o nlight s.co m
O pe n : M o nday – Fr i day | 8am –5p m E T
2
s m ar t vi s i on li g ht s. co m
PRODUCT DRAWING
4
3
2
1
72
52
B
10
active area
B
75
MALE 5 PIN M12 PIGTAIL
APPROX. 6 INCHES
38
4.50
42
37.50
4X
3.30
M4X0.7 - 6H
A
8
8
T-Slot
DETAIL A
SCALE 2 : 1
A
42
UNLESS OTHERWISE SPECIFIED:
3.18 13
1.25
DIMENSIONS ARE IN MM
TOLERANCES:
FRACTIONAL
ANGULAR: BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
5.04
7.50
A
PROPRIETARY AND CONFIDENTIAL
4
LIGHT PATTERNS
INTERPRET GEOMETRIC
TOLERANCING PER:
DRAWN
DATE
NC
5/26/2017
TITLE:
CAD files available
on our website.
SmartVisionLights.com
Dimensions
are in mm.
MATERIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
SmartVisionLights. ANY
FINISH
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
SmartVisionLights IS PROHIBITED.
DO NOT SCALE DRAWING
3
NAME
CHECKED
MP
5/26/2017
ENG APPR.
MP
5/26/2017
MFG APPR.
MP
5/26/2017
Q.A.
COMMENTS:
UNITS ARE IN
MILLIMETERS
SIZE DWG. NO.
B
REV
1
RM-75
SCALE: 1:1 WEIGHT:
2
SHEET 1 OF 1
1
LIGHTING ILLUMINATION FOR THE RM75
Continuous Operation Mode
Typical Output Performance
Illumination (Lux)
Distance = 100 mm
18,000
Smart Vision Lights recommends the RM75 be used at a
working distance between 50 mm to 200 mm.
Illumination measurement taken on White Light - 4800K
OverDriveTM Mode
Typical Output Performance
Illumination (Lux)
Distance = 100 mm
149,000
Illumination measurement taken on White Light - 4800K
The RM75 Mini Ring Light produces a uniform light pattern.
WD = Working Distance
175 mm
WD = 50 mm
WD = 100 mm
WD = 200 mm
(Grid set to 25 mm x 25 mm)
3
s m ar t vi s i on li g ht s. co m
MULTI-DRIVETM
Multi-Drive™ allowing users to
operate the light in continuous
operation or OverDrive™ strobe
(high-pulse operation) mode. An
advantage of Multi-Drive™ is faster imaging. It also enchances
capture/freeze motion imaging on high-speed lines.
The Multi-Drive™ feature allows the user to run the light
in continuous operation or OverDriveTM strobe mode at
maximum intensity. OverDrive™ strobe mode is up to ten
times the power of continuous operation.
DUTY CYCLE
(OVERDRIVETM MODE ONLY)
This section applies only if light is in OverDrive™ Mode.
The Duty Cycle (D) is related to the Strobe Time (ST) and
Rest Time (RT).
ILLUMINATION
Calculating Rest Time
RT =
ST
D
RM75 Series of Miniature “Mini” Ring Lights works best for:
- ST
RT = Rest Time
ST = Strobe Time
D = Duty Cycle
Example
RT =
10 ms
.1
- 10 ms = 90 ms
Rest Time is 90 ms for 10 ms Strobe Time
Dark Field
Maximum Duty Cycle for OverDriveTM light is 10% (0.1)
Radial
EYE SAFETY
According to IEC 62471: 2006. Full documentation available upon request.
Notice
Exempt Group: No photobiological hazard to eyes or skin even for continuous, unrestricted use. Applicable for wavelengths: 625,
850, and 940.
Caution
Risk Group 1: Possibly hazardous optical radiation emitted from this product. Do not stare at operating lamp. May be harmful to
eyes. Safe for most applications except prolonged exposure. Applicable for wavelengths: 470, 505, 530, and WHI.
4
s m ar t vi s i on li g ht s. co m
PART NUMBER
RM75
Part Number Examples:
RM75-625
(RM75, 625 Red Wavelength)
COLOR:
WHI
530
470
625
Additional wavelengths available upon request
MOUNTING
Mounting options include four (4) Tslots and four (4) M4 threaded
holes on the RM75 mini ring light.
Optional Mounting Adapter
Hardware included with light:
(2) M4 x 8 mm screws (Hex)
(2) M5 x 10 mm screws (Hex)
(2) T-Nuts
The optional
ADP0001-KIT can be
used to mount a camera,
filter adapter or a lens
directly to the RM75.
4
3
2
CAMERA MOUNTING ADAPTER
CAMERA
B
FILTER ADAPTER
LENS
(optional)
(optional)
1
SCREWS
MOUNTING BRACKET
RM-75
B
A
A
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MM
TOLERANCES:
FRACTIONAL
ANGULAR: BEND 3
TWO PLACE DECIMAL
THREE PLACE DECIMAL
PROPRIETARY AND CONFIDENTIAL
5
4
3
.05
.050
INTERPRET GEOMETRIC
TOLERANCING PER:
MATERIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
SmartVisionLights. ANY
FINISH
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
SmartVisionLights IS PROHIBITED.
DO NOT SCALE DRAWING
2
NAME
DATE
6/2/2017
DRAWN
NC
CHECKED
MP
6/2/2017
ENG APPR.
MP
6/2/2017
MP
6/2/2017
MFG APPR.
TITLE:
SmartVisionLights.com
Q.A.
COMMENTS:
SIZE
DWG. NO.
REV
RM-75 Mounting
s m ar t vi
li g ht s. co
1m
B s i on
Exploded
UNITS ARE IN
MILLIMETERS
SCALE: 1:1 WEIGHT:
1
SHEET 1 OF 1
ACCESSORIES
Step Up Kits *
Len Thread Size
25 mm
27 mm
30.5 mm
34 mm
35.5 mm
37 mm
39 mm
Power Cables
Step Down Kits
Part Number
Len Thread Size
SU25.5-46
SU27-46
SU30.5-46
SU34-46
SU35.5-46
SU37-46
SU39-46
49 mm
52 mm
55 mm
58 mm
62 mm
67 mm
72 mm
Part Number
SD49-46
SD52-46
SD55-46
SD58-46
SD62-46
SD67-46
SD72-46
Lengths
5m
Part Number
5PM12-5
10 m
5PM12-10
15 m
5PM12-15
Mounting Bracket
Description
Part Number
Camera Mount
ADP0001-KIT
* Additional sizes available
GLOSSARY
This glossary covers all Smart Vision Lights product families; some content in this section may not apply to this specific light.
TERMINOLOGY
OverDrive™ Lights include an integrated high-pulse driver for complete LED light control.
Continuous Operation Lights stays on continuously.
Multi-DriveTM Combines continuous operation and OverDrive™ strobe (high-pulse operation) mode into one easy-to-use light.
Built-in Driver The built-in driver allows full function without the need of an external controller.
Camera to Light Connecting the light directly to the camera, without the need for additional controllers or equipment.
Polarizers Filters that reduce reflections on specular surfaces.
Diffusers Used to widen the angle of light emission, reduce reflections and increase uniformity.
TYPES OF ILLUMINATIONS
COLOR/WAVELENGTHS LEGEND
Wavelengths options range from 365 nm to 1550 nm. *
Additional wavelengths available for many light families.
Projector
Dark Field
Radial
365 395
470
505
530
625
850
940
WHI
*See Part Number section for this light’s available standard wavelengths.
Bright Field
Direct
Axial
Line
Diffuse Panel
Backlight
Short Wave Infrared LEDs are available in 1050 nm, 1200 nm,
1300 nm, 1450 nm, and 1550 nm.
6
s m ar t vi s i on li g ht s. co m
Download PDF
Similar pages