Fire and Burglary System - Per Mar Security Services

Previous Menu
Fire and
Burglary System
User's Manual
5120XM
N8031 6/96
TABLE OF CONTENTS
SYSTEM OVERVIEW......................................................................................3
General..........................................................................................................3
Zones.............................................................................................................3
Fire & Emergency Protection ......................................................................3
Burglary Protection.......................................................................................4
Alarms........................................................................................................... 4
Memory of Alarm .........................................................................................4
ABOUT THE KEYPADS ..................................................................................5
General..........................................................................................................5
Keypad Displays...........................................................................................5
FUNCTIONS OF THE REMOTE KEYPAD ..................................................6
TYPICAL ALPHA KEYPAD..............................................................................7
FIXED-WORD KEYPAD DISPLAYS..............................................................8
REMOTE KEYPAD USER CODES ...............................................................9
General..........................................................................................................9
Duress Code.................................................................................................9
Quick Arming..............................................................................................10
To Assign, Change, or Delete User Codes ..............................................10
REMOTE KEYPAD EMERGENCY KEYS...................................................11
Using Emergency Keys .............................................................................11
Emergency Key Programmed Functions .................................................12
NORMAL STANDBY OPERATION .............................................................13
FIRE ALARM PROTECTION .......................................................................14
General........................................................................................................14
In case of Fire .............................................................................................14
Silencing and Resetting a Fire Alarm .......................................................15
BURGLARY PROTECTION ENTRY/EXIT DELAYS .................................16
General........................................................................................................16
Exit Delay Alerting Sound ..........................................................................16
CHECKING FOR FAULTED BURGLARY ZONES ...................................17
Using the READY Key ...............................................................................17
BYPASSING BURGLARY PROTECTION ZONES ................................... 18
Using the BYPASS Key ............................................................................. 18
Quick Bypass ............................................................................................. 19
ARMING PERIMETER BURGLARY PROTECTION ONLY (STAY) ...... 20
ARMING PERIMETER BURG. PROTECTION ONLY (INSTANT) ........ 21
ARMING ALL BURGLARY PROTECTION (AWAY)................................. 22
ARMING ALL BURGLARY PROTECTION (MAXIMUM)......................... 23
DISARMING BURGLARY PROTECTION,
AND SILENCING BURGLARY ALARMS............................................... 24
BURGLARY PROTECTION EXIT ALARMS .............................................. 25
Burglary Protection Exit Alarm Warning Displays and Sounds ............. 25
EMERGENCY AND 24 HOUR NON-FIRE ALARMS............................... 26
General ....................................................................................................... 26
Silencing and Resetting an Emergency Alarm ........................................ 26
SUPERVISORY CONDITIONS ................................................................... 27
General ....................................................................................................... 27
Silencing and Resetting a Supervisory Indication.................................... 27
TROUBLE CONDITIONS............................................................................. 28
General (AC LOSS, SYSTEM LO BAT, COMM FAILURE, CHECK)........... 28
Silencing and Resetting a Trouble Indication ........................................... 29
CHIME MODE ............................................................................................... 29
ACTIVATING A FIRE DRILL TEST ............................................................. 30
ACTIVATING A BURGLARY WALK TEST................................................. 31
QUICK GUIDE TO SYSTEM FUNCTIONS ............................................... 32
SUMMARY OF AUDIBLE/VISUAL NOTIFICATION ................................. 33
PROTECTION ZONES LIST........................................................................ 35
FCC STATEMENTS ..................................................................................... 36
LIMITATIONS STATEMENT........................................................................ 38
SERVICING INFORMATION....................................................................... 39
WARRANTY .................................................................................. Back Cover
This manual is a step-by-step guide that will aquaint you with the system's features and benefits. It defines the components and
their functions, describes their operation, and instructs you with normal and emergency procedures.
Keep this manual in a convenient place so that you can refer to it as necessary.
–2–
SYSTEM OVERVIEW
General
Congratulations on your ownership of an Ademco Alarm System. You've made a
wise decision in choosing it, for it represents the latest in alarm protection
technology today, including microcomputer technology to monitor all system status.
Ademco is the world's largest manufacturer of security systems and millions of
premises are protected by Ademco systems.
Your system is a UL Listed commercial fire/burglary alarm control/communicator. It
provides up to three forms of protection: fire alarm, burglary alarm and emergency
alarm warning, some or all of which may be included in your system. In addition to
the control panel, your system will include at least one remote control keypad
which provides full control of system operation, external alarm sounders and
various types of sensors such as smoke detectors for fire protection, door/window
contacts for perimeter burglary protection and passive infrared motion detectors for
interior burglary protection.
Please disregard references to burglary and/or emergency protection in the text
that follows if your system does not provide these types of protection.
Zones
Your system has five protection zones. Your installer has assigned each of your
system's sensing devices to one of these zones. For example, warehouse smoke
detectors may have been assigned to zone 01, a fire sprinkler supervisory switch
may have been assigned to zone 02, burglary door/window contacts may have
been assigned to zone 3, etc.. The keypad will display these zone numbers when
an alarm, supervisory or trouble condition is detected.
Fire & Emergency
Protection
The fire and emergency protection portions of your system are always on and will
sound an alarm if an alarm condition is detected.
–3–
SYSTEM OVERVIEW
Burglary Protection
The burglary protection portion of your system must be turned on or "armed"
before it can sense burglary alarm conditions and sound an alarm. Your system
can be armed in one of four modes: STAY, AWAY, INSTANT and MAXIMUM.
Refer to the ARMING THE SYSTEM sections of this manual for instructions on
using these modes.
Your system also provides a CHIME mode for alerting you to the opening and
closing of doors and windows while your burglary protection is disarmed.
Alarms
When an alarm occurs, both the keypad and external sounders will sound, and a
message at the keypad will identify the zone(s) causing the alarm. In addition, if
your system is connected to a central monitoring station, an alarm message will be
sent. You may stop the sound by entering the OFF sequence (user code + OFF
key) at your keypad .
Memory Of Alarm
When an alarm, supervisory or trouble condition occurs, the keypad displays the
number(s) of the zone(s) that caused the problem, and displays the type of
condition present (ex. FIRE, ALARM, SUPV, CHECK). The display remains until it
is cleared by entering the OFF sequence (user code + OFF key) a second time.
–4–
ABOUT THE OPTIONAL KEYPADS
General
The keypads feature a telephone style (digital) keypad and a Liquid Crystal
Display (LCD) which shows the nature and location of all occurrences.
The keypads feature a built-in sounder which emits the same alarm sounds as the
control's built-in warning buzzer during alarm conditions.
The keypad's display screen displays the same indications as the control's built-in
LED indicators, and in addition, displays the zone number of faulted zones as well
as the type of fault (i.e. alarm, supervisory or trouble) present. The telephone
style keypad keys allow entry of commands for silencing the warning sounds,
resetting faulted smoke detectors, activating various system tests, etc.
Keypad Displays
There are two basic types of keypad displays, Alpha and Fixed-Word, either of
which may have been used in your system.
• Alpha Keypad Displays feature a 2-line, 32 character alphanumeric Liquid
Crystal Display (LCD) which can display the nature and location of all
occurrences in friendly English.
• Fixed-Word Keypad Displays are functionally similar to the Alpha Keypads,
except that their LCD display uses pre-designated (fixed) words to identify the
nature and location of occurrences.
Unless stated otherwise, all commands and procedures described herein apply
equally to all keypads.
ARMED
READY
OFF
ARMED
Alpha
Keypad
READY
A
OFF
OFF
AWAY
AWAY
STAY
1
2
3
3
B
MAX
MAX
TEST
TEST
BYPASS
4
5
5
6
6
C
INSTANT
INSTANT
CODE
CHIME
CHIME
7
7
8
9
9
0
0
#
#
D
A
B
Fixed-Word
Keypad
READY
READY
*
*
PANIC
–5–
C
AWAY
STAY
1
2
3
MAX
TEST
BYPASS
4
5
6
INSTANT
CODE
CHIME
7
8
9
0
#
READY
*
PANIC
FUNCTIONS OF THE REMOTE KEYPAD
SEE TYPICAL ALPHA KEYPAD ON NEXT PAGE
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
DISPLAY WINDOW: Displays zone # and system status
messages.
1 OFF Key: Silences audible alarm, supervisory and
trouble sounds, clears visual display after problem's
correction, and disarms the burglary protection.
2 AWAY Key: Arms interior and perimeter burglary protection. Entry and exit delays are provided.
3 STAY Key: Arms perimeter burglary protection only.
Interior burglary protection is not armed, allowing
movement within premises without causing alarm.
Entry and exit delays are provided.
4 MAXIMUM Key: Arms in manner similar to AWAY
key, except no entry delay is provided. An alarm will
occur immediately upon opening any door or window.
This mode provides maximum protection.
5 TEST Key: Tests the burglary and emergency portions of your system.
6 BYPASS Key: Removes individual protection zones
from being monitored by the system.
7 INSTANT Key: Arms in manner similar to STAY key,
but except that no entry delay is provided. An alarm will
occur immediately upon opening any door or window.
8 CODE Key: Used to assign additional 4-digit user
codes.
9 CHIME Key: Turns CHIME mode on and off. When
on, with burglary protection disarmed, the opening of a
door or window will sound 3 beeps at your keypad(s).
✱ READY Key: Displays all open protection zones.
Burglary zone faults must be corrected or bypassed
prior to arming.
12.
13.
14.
15.
16.
17.
–6–
Key: "Quick Arm" key that permits burglary protection
to be armed without use of a user code. Also activates
fire drill.
0 – 9 Keys:Used to enter your 4-digit user code.
Most system functions are performed by
first entering the 4-digit user code and
then entering one of the above command
keys (e.g., OFF, AWAY, STAY, etc).
READY INDICATOR: (GREEN) Lit when burglary portion
of your system is ready to be armed (no faults present). While burglary protection is disarmed, this indicator goes off and on as protection zones are faulted
and unfaulted.
ARMED INDICATOR: (RED) Lit when the burglary portion
of your system has been armed in STAY, AWAY,
MAXIMUM or INSTANT mode.
INTERNAL SOUNDER: Sound is: slow on/off pulsing for
fire alarms, steady dual-tone for burglary and emergency alarms, and rapid on/off pulsing for supervisory
and trouble conditions. Also "beeps" during other
system functions.(see SUMMARY OF AUDIBLE/
VISUAL NOTIFICATION).
#
A ,
B , C EMERGENCY Keys: Your installer may
have programmed these keys for manual activation of
fire or emergency alarms. Note: Other keys may be
available for emergency functions (see page 11).
N o t e : More information about user codes, the various command keys, and the emergency keys is provided in
the sections that follow.
1
2
5
3
4
6
ARMED
READY
A
15
A
14
B
B
C
C
16
D
OFF
OFF
AWAY
AWAY
STAY
11
22
3
3
MAX
TEST
TEST
BYPASS
44
5
5
6
6
INSTANT
INSTANT
CODE
CHIME
CHIME
7
7
8
9
9
0
0
#
#
8
9
10
READY
READY
*
*
17
7
11
PANIC
12
13
SHOWN WITH
KEYPAD COVER
REMOVED
TYPICAL ALPHA KEYPAD
Fixed-Word Keypads are functionally similar, except for screen displays.
IMPORTANT!: When entering codes and commands, sequential key depressions must
be made within 2 seconds of one another. If 2 seconds elapses without a key depression,
the entry is aborted and must be repeated from its beginning.
–7–
FIXED-WORD KEYPAD DISPLAYS
READY The burglary protection is ready to be armed (no faults are present).
NOT READY The burglary protection is not ready to be armed because one or
more zones are faulted.
AWAY All burglary protection, interior and perimeter, is armed.
Note: "AWAY" appears when armed AWAY and "AWAY INSTANT"
appears when armed MAXIMUM.
AC
AWAY SUPV NOTEST
S T A Y Only perimeter burglary protection, such as windows and doors is
BYPASS
NOT READY
armed. Note: "STAY" appears when armed STAY and "STAY
ALARM STAY
CHIME BAT
INSTANT" appears when armed INSTANT.
FIRE CHECK INSTANT
INSTANT Burglary protection is armed with no entry delay provided. Also see
AWAY and STAY above.
FIXED-WORD DISPLAY
F I R E Appears when a fire alarm is detected. Accompanied by a display
of the zone # in alarm.
ALARM Appears when any type of alarm is detected. "FIRE" also appears
when a fire alarm is detected. Accompanied by a display of the
zone # in alarm.
S U P V Appears when a fire sprinkler system supervisory condition is detected. Accompanied by a display of the zone #
having the supervisory condition.
CHECK Appears when a fire zone wiring fault is detected at any time, or when a DAY(Trouble) / NIGHT(Alarm) burglary zone
fault is detected while burglary protection is disarmed. Also appears when certain system problems such as phone
line problems are detected.Accompanied by a display of the zone # in trouble.
A C Appears when AC power is present.
NO AC Appears when AC power is low, or not present. System is operating from backup battery power.
BAT Appears when backup battery is low or disconnected.
T E S T Appears when the system is operating in one of its test modes (such as the fire drill test mode).
B Y P A S S Appears when one or more zones have been bypassed and are no longer operational.
C H I M E Appears when the CHIME feature is ON.
05
–8–
REMOTE KEYPAD USER CODES
General
Duress Code
USER
#
2
3–6
8
(Duress)
Your installer will have programmed a 4-digit user code (known as User Number 2
code) that can be entered at your keypad to silence/reset alarms, arm/disarm your
burglary protection, bypass protection zones and activate the fire drill test and the
burglary walk test. This code may also be used to assign up to four other user
codes (known as User Number 3–6 codes) and to assign a Duress code
The User Number 3–6 codes are intended for users who need limited and/or
temporary control over system operation. These codes can perform the same
functions as the User Number 2 code except for assigning user codes and
activating the fire drill test.
The Duress code (it corresponds to User Number 8) is intended for use when
one is forced to arm or disarm the burglary protection portion of the system under
threat. When used, this code will arm or disarm the system apparently normally,
but will also send a silent alarm message to the central station so that appropriate
action can be taken.
Generally, most keypad functions are performed by first entering the 4-digit user
code and then entering one or more command keys, as described in the sections
that follow. The user code functions are summarized in the table below.
ARM/DISARM
BURGLARY
Yes
Yes
Yes
(Trips silent
emergency)
SILENCE
ALARM/SUPV/TROUBLE
Yes
Yes
ADD/CHANGE
USERS
Yes (Users 2–8)
No
BYPASS
ZONES
Yes (Burglary
& Emergency)
Yes
No
No
–9–
ENTER TEST MODES
Burg. Walk Test Fire Drill Test
Yes
Yes
Yes
No
No
No
REMOTE KEYPAD USER CODES
Quick Arming
Ask your installer if "Quick
Arming" is active for your
system, and if so, check
here:
To Assign, Change,
or Delete
User Codes
4-DIGIT USER CODES
It is recommended that
obvious codes such as
1111 or 1234 not be
assigned.
If your system supports "Quick Arming", the "#" key can be pressed in place of
the user code when arming the burglary protection. The user code is always
required, however, when disarming.
User Number 2 can change, but not delete, his/her own code and can assign,
change, or delete codes for User Numbers 3–8
User Numbers 3–8 cannot assign, change, or delete user codes.
1. Enter the User Number 2 code and press the CODE key.
2. Enter a single-digit User Number (2–8) for the user whose code is to be
assigned, changed, or deleted. Note: The Duress code corresponds to User
Number 8.
3. If assigning or changing a user's code, enter the new 4-digit code for that
user. The keypad will beep once, indicating that the new code has been
accepted.
If deleting a user's code, perform steps 1 and 2 and then stop. After a few
moments the keypad will beep once, indicating that the existing code has been
deleted.
–10–
REMOTE KEYPAD EMERGENCY KEYS
Using
Emergency Keys
(for manually activating
silent and/or
audible alarms)
Also see
Duress Code
feature on
page 9
Your installer may have programmed the keypad's A, B, or C emergency keys to
allow manual activation of fire and/or emergency alarms. The functions that might
be programmed are: Fire, Silent Emergency, Audible Emergency, and Personal
Emergency.
A fire alarm sends a fire alarm message to the central station* and uniquely
sounds at keypad(s) and external bells and sirens. A FIRE message plus a zone
number (see table on next page) is also displayed.
A silent emergency sends a silent alarm signal to the central station*, but there is
no audible alarm or visual display.
An audible emergency sends a signal to the central station* and sounds a loud,
steady alarm at your keypad(s) and at any external sounders that may be connected An ALARM message plus a zone number (see table on next page) is also
displayed.
A personal emergency alarm sends an emergency message to the central
station* and sounds at keypad(s), but not at external bells or sirens. An ALARM
message plus a zone number (see table on next page) is also displayed.
* If connected to a central station.
TO MANUALLY ACTIVATE AN EMERGENCY FUNCTION AT ANY TIME OF DAY
OR NIGHT
(SEE TABLE AND DIAGRAM ON NEXT PAGE)
Press the programmed A , B , or C emergency key for at least two seconds,
or alternatively,
Press both keys of the corresponding 1 & ✱ (A), ✱ & # (B), or 3 & # (C) emergency key
pair
at the same time.
–11–
REMOTE KEYPAD EMERGENCY KEYS
CHECK IF
ACTIVE
EMERGENCY
KEY(S)
P R O G R A M M E D
F U N C T I O N
ZONE
NUMBER
[A]
____FIRE, ____SILENT, ____AUDIBLE, ____PERSONAL
95
[B]
____FIRE, ____SILENT, ____AUDIBLE, ____PERSONAL
07
SEE YOUR INSTALLER
[C]
____FIRE, ____SILENT, ____AUDIBLE, ____PERSONAL
96
AND NOTE HERE
OR
THE KEY(S) & FUNCTION(S)
[1] & [✱]
____FIRE, ____SILENT, ____AUDIBLE, ____PERSONAL
95
PROGRAMMED
[✱] & [#]
____FIRE, ____SILENT, ____AUDIBLE, ____PERSONAL
07
[3] & [#]
____FIRE, ____SILENT, ____AUDIBLE, ____PERSONAL
96
FOR YOUR SYSTEM
• KEY [D] ON YOUR KEYPAD IS NOT ACTIVE HERE.
A
LETTERED
PANIC
KEYS
("D" IS
NOT USED)
B
<
C
AWAY
STAY
1
2
3
MAX
TEST
BYPASS
4
5
6
INSTANT CODE
7
D
TYPICAL
KEYPAD
OFF
1 & ✱
3 & #
PAIRED
CHIME
8
9
0
#
> PANIC
KEYS
READY
✱
PANIC
–12–
✱ & #
NORMAL STANDBY OPERATION
Your system provides the following indications while the burglary protection is disarmed and there are no alarm,
supervisory, or trouble conditions present:
• The keypad warning buzzer and external alarm sounders are off.
• The Alpha keypad's LCD displays "DISARMED – READY TO ARM" if your system provides burglary protection,
or "SYSTEM NORMAL" if your system does not provide burglary protection.
**** SYSTEM ****
**** NORMAL ****
****DISARMED****
READY TO ARM
The Fixed-Word keypad's LCD displays "AC".
AC
–13–
FIRE ALARM PROTECTION
General
Your fire alarm system is on 24 hours a day, for continuous protection. In the event
of an emergency, the strategically located smoke and heat detectors will automatically send signals to your system, triggering sounds from your keypad and
exterior sounders. A FIRE message will appear at your keypad and remain on until
you silence the alarm and reset the system.
In Case Of Fire
WHEN FIRE ALARM SOUNDS ARE HEARD, EVACUATE
ALL OCCUPANTS FROM THE PREMISES IMMEDIATELY
AND NOTIFY YOUR LOCAL FIRE DEPARTMENT.
Your system provides the following indications when your system's smoke and/or
heat detectors have detected a fire alarm condition.
• The keypad buzzer produces a slow on/off pulsing sound.
• The external fire alarm sounders produce either:
a steady sound
or
a pulsing sound,
depending on what your installer selected (check the appropriate box).
• The keypad LCD displays the word "FIRE" (Alpha) or "FIRE ALARM"
(Fixed-Word) along with the number of the zone in alarm.
FIRE 05
FILE ROOM
ALPHA
05
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT TAMPER
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
FIXED-WORD
• A fire alarm message is sent to the central station.
If your system has a keypad with a FIRE alarm emergency key, then these
indications may be manually triggered by pressing this key for at least 2
seconds, (or the corresponding emergency key pair), should you become aware
of a fire emergency before your detectors sense the problem.
–14–
FIRE ALARM PROTECTION
Silencing
and Resetting
a Fire Alarm
To silence the keypad buzzer and external alarm sounders:
Enter your User Code followed by the OFF key.
The keypad's LCD will display "FIRE ALARM SILENCED" (Alpha) or "SF"
(Fixed-Word) to indicate that a fire alarm condition may still be present. The Alpha
keypad will display the number of the zone in alarm as a Memory of Alarm
indication. The Fixed-Word keypad alternates the zone number in alarm with the
"SF" display.
FIRE O5 FIRE
ALARM SILENCED
ALPHA
5F
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
TAMPER
FIXED-WORD
To reset your system's smoke detectors and the keypad Memory of Alarm
display (after heat or smoke is no longer present):
First determine and correct the cause of the fire alarm condition (e.g., fan smoke from
the smoke detector chamber, reset the pull station, etc.) and then:
Re-enter your User Code plus the OFF key.
Note: To silence and reset a burglary alarm, see page 24.
See the SUMMARY OF AUDIBLE/VISUAL NOTIFICATION section for
information which will help you to distinguish between FIRE and
BURGLARY alarm sounds.
–15–
BURGLARY PROTECTION ENTRY/EXIT DELAYS
General
The burglary protection portion of your system has preset time delays, known as
exit delay and entry delay. When you arm your burglary protection, exit delay
gives you time to leave through the entry/exit door without setting off an alarm.
Entry delay gives you time to disarm the burglary protection when you reenter
through the entry/exit door. The burglary protection must be disarmed, however,
before the entry delay period ends, or an alarm will occur. The keypad will beep
slowly during the entry delay period, reminding you to disarm the burglary
protection.
You can also arm the protection with no entry delay at all by using either INSTANT
or MAXIMUM arming modes. These modes can provide greater security while you
are sleeping or while you are away for extended periods of time.
Exit Delay
Alerting Sound
If active for your system, and if so-programmed by your installer, when arming
your burglary protection AWAY (see page 22) or MAXIMUM (see page 23), slow
beeps will sound from the keypad during exit delay, turning to fast beeps during
the final five seconds of the delay time.
Ask your installer if
this is active for your
system, and if so,
check here:
See your installer for your delay times and record them here:
Exit Delay:
seconds
Entry Delay:
–16–
seconds
CHECKING FOR FAULTED BURGLARY ZONES
Using the Before arming the burglary protection portion of your system, all protected doors,
✱ READY Key windows and other protection zones must be closed or bypassed (see
BYPASSING BURGLARY PROTECTION ZONES section), otherwise the
keypad will display a "Not Ready" message, and your keypad's READY indicator
light will not be lit. The READY (✱ ) key can be used to display all faulted burglary
zones, making it easier for you to secure any open zone.
To display faulted burglary zones, simply press and release the READY (✱ ) key
(do not enter your user code first). Secure or bypass the zones displayed before
arming the system.
A "Ready" message will be displayed when all protection zones have been either
closed or bypassed and the keypad's READY indicator light will be lit.
TO DISPLAY FAULTED ZONES, PRESS THE READY KEY.
TYPICAL DISPLAYS
WHEN NOT READY TO ARM
TYPICAL DISPLAYS
INDICATING FAULTED PROTECTION ZONE
(AFTER PRESSING READY KEY)
TYPICAL DISPLAYS
INDICATING "READY TO ARM"
DISARMED - PRESS *✱
TO SHOW FAULTS
FAULT 03 FRONT
UPSTAIRS STORAGE
****DISARMED****
READY TO ARM
ALPHA
ALPHA
ALPHA
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
FIXED-WORD
TAMPER
03
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
FIXED-WORD
–17–
TAMPER
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
FIXED-WORD
TAMPER
BYPASSING BURGLARY PROTECTION ZONES
Using the
6 BYPASS Key
All burglary zone
bypasses are removed
when an OFF sequence
(user code plus OFF) is
performed.
This key is used when you want to arm the burglary protection portion of your
system with one or more zones intentionally unprotected. The burglary protection
must be disarmed first.
1. Enter your user code and press the BYPASS key.
2. Enter zone number(s) for the zone(s) to be bypassed (e.g., 02, 03, etc.).
Single digit zone numbers must be preceded by a zero.
3. When finished, the keypad will momentarily display a "Bypass" message for
each bypassed zone number. Wait for these zones to be displayed, to confirm
their bypass.
4. Arm the system's burglary protection as usual.
Bypassed zones are unprotected and will not cause an alarm if violated
while your burglary protection is armed.
TO BYPASS ZONES:
• ENTER USER CODE.
• PRESS BYPASS KEY.
• ENTER ZONE Nos.
• WAIT FOR BYPASSED ZONES
TO BE DISPLAYED.
• ARM BURGLARY PROTECTION
AS USUAL.
TYPICAL MOMENTARY DISPLAYS
OF BYPASSED ZONE
BYPASS 03 FRONT
UPSTAIRS STORAGE
ALPHA
03
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
FIXED-WORD
–18–
TAMPER
BYPASSING BURGLARY PROTECTION ZONES
Quick Bypass
Ask your installer if
"Quick Bypass" is active
for your system, and if
so, check here:
If your system supports "Quick Bypass", it allows you to easily bypass all open
(faulted) burglary zones without having to enter zone numbers individually. This
feature is useful if, for example, you routinely leave certain windows open when
arming at night.
To use this feature, enter your user code, press the BYPASS key, then stop. In a
few moments, all faulted burglary protection zones will be displayed along with a
"Bypass" message. Wait for all bypassed zones to be displayed, then arm the
burglary protection as usual.
TYPICAL DISPLAYS
"READY TO ARM WITH ZONES BYPASSED"
BURGLARY PROTECTION
CAN NOW BE ARMED
WITH ZONE(S) BYPASSED.
DISARMED BYPASS
READY TO ARM
ALPHA
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
FIXED-WORD
–19–
TAMPER
ARMING PERIMETER BURGLARY PROTECTION ONLY
WITH ENTRY DELAY ON
Using the
3 STAY Key
BEFORE ARMING, close
all doors and windows (see
CHECKING FOR FAULTED
BURGLARY ZONES on page
17).
Use this key when you are staying inside, but expect someone to use an
entry/exit door later.
1. Enter your user code and press the STAY key.
2. The keypad beeps three times and displays the armed message. The red
ARMED indicator lights.
3. The system arms. A burglary alarm sounds immediately if a protected perimeter
window or non-entry/exit door is then opened, but you may otherwise move
freely throughout the premises.
Later arrivals can enter through an entry/exit door without causing an
alarm, but they must disarm the burglary protection during the entry delay
period to avoid sounding an alarm.
USER CODE + STAY KEY
ARMS THE PERIMETER,
BUT ALLOWS USE OF
THE ENTRY/EXIT DOOR.
TYPICAL DISPLAYS
"ARMED STAY"
ARMED ***STAY***
X
ALPHA
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
FIXED-WORD
–20–
TAMPER
ARMING PERIMETER BURGLARY PROTECTION ONLY
WITH ENTRY DELAY OFF
Using the
7 INSTANT Key
BEFORE ARMING, close
all doors and windows (see
CHECKING FOR FAULTED
BURGLARY ZONES on page
17).
Use this key when you are staying inside and do not expect anyone to
use an entry/exit door.
1. Enter your user code and press the INSTANT key.
2. The keypad beeps three times and displays the armed message. The red
ARMED indicator lights.
3. The burglary protection arms. A burglary alarm sounds immediately if any
protected perimeter door or window is opened, but you may otherwise move
freely throughout the premises.
An alarm sounds immediately if anyone opens an entry/exit door.
USER CODE + INSTANT KEY
ARMS THE PERIMETER
(INCLUDING THE ENTRY/EXIT DOOR),
WITH NO ENTRY DELAY.
TYPICAL DISPLAYS
"ARMED INSTANT"
ARMED *INSTANT*
X
ALPHA
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
FIXED-WORD
–21–
TAMPER
ARMING ALL BURGLARY PROTECTION
WITH ENTRY DELAY ON
Using the
2 AWAY Key
BEFORE ARMING, close
all doors and windows (see
CHECKING FOR FAULTED
BURGLARY ZONES on page
17).
Use this key when no one will be staying inside.
1. Enter your user code and press the AWAY key.
2. The keypad beeps twice and displays the armed message. The red ARMED
indicator lights.
3. You may leave through an entry/exit door during the exit delay period without
causing an alarm.
After exit delay, the burglary protection arms and sounds an alarm immediately
if a protected window or non-entry/exit door is then opened, or if any
movement is detected inside your premises.
You may reenter through an entry/exit door, but must disarm the burglary
protection during the entry delay period to avoid an alarm.
USER CODE + AWAY KEY
ARMS ALL BURGLARY PROTECTION
(INTERIOR AND PERIMETER),
BUT ALLOWS USE OF THE
ENTRY/EXIT DOOR.
TYPICAL DISPLAYS
"ARMED AWAY"
ARMED ***AWAY***
YOU MAY EXIT NOW
"YOU MAY EXIT NOW" disappears
when exit delay expires.
ALPHA
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
FIXED-WORD
–22–
TAMPER
ARMING ALL BURGLARY PROTECTION
WITH ENTRY DELAY OFF
Using the
4 MAXIMUM Key
BEFORE ARMING, close
all doors and windows (see
CHECKING FOR FAULTED
BURGLARY ZONES on page
17).
Use this key when the premises will be vacant for extended periods of
time such as vacations, etc., or when retiring for the night and no one will be
moving through protected interior areas.
1. Enter your USER code and press the MAXIMUM key.
2. The KEYPAD beeps twice and displays the armed message. The red ARMED
indicator lights.
3. You may leave through an entry/exit door during the exit delay period without
causing an alarm.
After exit delay, the burglary protection arms and sounds an alarm immediately
if any protected door or window is opened, or if any movement is detected
inside your premises.
An alarm sounds immediately, when someone reenters.
USER CODE + MAXIMUM KEY
ARMS ALL BURGLARY PROTECTION
(INTERIOR AND PERIMETER),
(INCLUDING THE ENTRY/EXIT DOOR
WITH NO ENTRY DELAY).
TYPICAL DISPLAYS
"ARMED MAXIMUM"
ARMED *MAXIMUM*
YOU MAY EXIT NOW
"YOU MAY EXIT NOW" disappears
when exit delay expires.
ALPHA
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
FIXED-WORD
–23–
TAMPER
DISARMING BURGLARY PROTECTION
AND SILENCING BURGLARY ALARMS
Using the
1 OFF Key
IMPORTANT:
If you return and the
main burglary sounder is
on, DO NOT ENTER, but
CONTACT THE POLICE from a
nearby safe location.
If you return after an
alarm has occurred and
the main sounder has
shut itself off, the keypad
will beep rapidly upon your
entering, indicating that an
alarm has occurred during
your absence.
LEAVE IMMEDIATELY, and
CONTACT THE POLICE from a
nearby safe location.
The OFF key is used to disarm the burglary protection and to silence burglary
alarm sounds.
To Disarm Burglary Protection
Enter your user code and press the OFF key. The "Ready" message will be
displayed (providing no burglary zone is faulted), and the keypad will beep once
to confirm that burglary protection is disarmed.
To Silence and Reset a Burglary Alarm
SEE IMPORTANT NOTE AT LEFT!
Enter your user code and press the OFF key to silence the alarm (or warning
tones of a Memory of Alarm). Note the zone in alarm on the keypad display, and
make that zone intact (close door, window, etc.). Now re-enter your user code
plus the OFF key again to clear the keypad's Memory of Alarm display. If the
display will not clear and does not provide a "Ready" message, notify the alarm
agency.
To Silence and Reset a Fire Alarm see page 15.
See the SUMMARY OF AUDIBLE/VISUAL NOTIFICATION section for
information which will help you to distinguish between FIRE and
BURGLARY alarm sounds.
–24–
BURGLARY PROTECTION EXIT ALARMS
Burglary Protection
Exit Alarm Warning
Displays and Sounds
Ask your installer if "Exit
Alarm Warning" is active
for your system, and if
so, check here:
The burglary protection portion of your system may have been programmed for
this feature.
When arming your burglary protection, if an exit or interior zone contains a fault
during closing at the time the exit delay ends, the alarm sounder and keypad sound
continuously to alert you that an unwanted alarm can be prevented if you take
action:
• If you disarm the burglary protection during the entry delay period that will
immediately follow, the sound stops. The keypad displays "CANCELLED
ALARM "or "CA" as well as a zone indication. No message is transmitted to the
central station.
• If the burglary protection is NOT disarmed during the immediately following entry
delay period, the sounds continue until the system is disarmed (or alarm sounder
timeout occurs). The keypad displays "EXIT ALARM" or "EA" as well as a zone
indication. An "exit alarm" message will be sent to the central station.
Note: The latter "EXIT ALARM" conditions also result if an alarm from an exit or
interior zone occurs within two minutes after the end of an exit delay.
In any of the above cases, a second OFF sequence (user code + OFF key) will
clear the keypad display.
–25–
EMERGENCY AND 24 HOUR NON-FIRE ALARMS
General
Your system may have sensors which detect non-fire related alarm conditions, such as the
triggering of an HVAC (Heating, Ventilating, or Air Conditioning) temperature sensor, the
pressing of a holdup alarm button, etc. Your system may provide some or all of the
indications listed below, depending on what your installer selected to occur when one of
those conditions is detected.
If your system's keypad has any active emergency alarm key(s) (see REMOTE KEYPAD
EMERGENCY KEYS on page 11) these indications may be manually triggered by
pressing the appropriate emergency key (or corresponding emergency key pair).
• The keypad buzzer produces a steady sound (no sound for silent alarms).
• The external alarm sounders produce a steady sound (no sound for silent alarms).
• The keypad LCD (Fixed-Word) displays the word "ALARM" and the zone number in
alarm. Alpha keypads also display a description of the zone in alarm (no keypad displays
for silent alarms).
ALARM 02
TEMPERATURE
02
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
INSTANT
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
TAMPER
ALPHA
FIXED-WORD
• An emergency alarm message is sent to the central station.
Silencing
and Resetting
an Emergency Alarm
To silence the keypad buzzer
and external alarm sounders:
Enter your User Code,
followed by the OFF key.
The keypad's LCD will display the
number of the zone in alarm as
a Memory of Alarm indication.
–26–
To reset the keypad alarm display:
First correct the cause of the alarm
condition, and then:
Re-enter your User Code,
followed by the OFF key.
SUPERVISORY CONDITIONS
General
If your building has a fire sprinkler system, your installer may have installed a
sensor which monitors the sprinkler system (e.g., to determine whether the main
water gate valve is open or that there is adequate water pressure, etc.). Your
system provides the following indications when a supervisory condition is
detected.
CALL YOUR INSTALLER IMMEDIATELY FOR SERVICE WHEN A
SUPERVISORY INDICATION APPEARS! For servicing information, see page 39.
• The keypad buzzer produces a rapid on/off pulsing sound.
• The keypad LCD displays the word "SUPV" and the number of the zone with
the supervisory condition. Alpha keypads also display a description of the zone.
SUPV 04
SPRINKLER VALVE
ALPHA
04
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
TAMPER
FIXED-WORD
• A supervisory message is sent to the central station.
Silencing
and Resetting
a Supervisory
Indication
To silence the keypad buzzer:
Enter your User Code,
followed by the OFF key
The keypad's LCD will display the
number of the zone having the
supervisory condition as a Memory
indication.
–27–
To reset the keypad supervisory
display:
First have the cause of the indication
corrected, and then:
Re-enter your User Code,
followed by the OFF key.
TROUBLE CONDITIONS
General
Your system monitors each of your protection zones and various aspects of
system operation for problems such as wire breaks, loss of AC power, faulted
telephone lines, etc., which compromise proper operation. Your system provides
the following indications when one of these problems is detected.
CALL YOUR INSTALLER IMMEDIATELY FOR SERVICE, WHEN ANY OF
THESE INDICATIONS APPEAR FOR A CONDITION THAT CANNOT BE
CORRECTED BY YOU! For servicing information, see page 39.
• The keypad buzzer produces a rapid on/off pulsing sound.
• The keypad LCD displays "AC LOSS" (Alpha) or "NO AC" (Fixed-Word) when AC power
is low or not present.
• The keypad LCD displays "SYSTEM LO BAT" (Alpha) or "BAT" (Fixed-Word) when your
system's back-up battery is low or disconnected.
• The keypad LCD displays "COMM FAILURE" (Alpha) or "FC" (Fixed-Word) when
attempts to send a message to the central station have failed.
• The keypad LCD (Fixed-Word) displays "CHECK" and a protection zone number (1–5)
or system zone number (6–12) when there is a zone or system related problem. Alpha
keypads also display a description of the zone.
CHECK 03 FRONT
UPSTAIRS STORAGE
ALPHA
03
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
TAMPER
FIXED-WORD
• A trouble message is sent to the central station.
N o t e : If your keypad LCD displays "0C" for more than 5 minutes, then it is not receiving
signals from the control panel. CALL YOUR INSTALLER IMMEDIATELY FOR SERVICE.
–28–
TROUBLE CONDITIONS
Silencing
and Resetting
a Trouble Indication
To silence the keypad buzzer:
Enter your User Code,
followed by the OFF key.
The keypad's LCD will display the
number of the zone in trouble as
a Memory indication.
To reset the keypad trouble display:
First have the cause of the trouble
condition corrected, and then:
Re-enter your User Code,
followed by the OFF key.
CHIME MODE
Using the
9 CHIME Key
This feature can be used
only while the burglary
protection portion of your
system is disarmed.
By using the CHIME mode, your system can be set to alert you to the opening of
a door or window while the burglary protection portion of the system is disarmed.
When activated, three tones will sound at the keypad whenever a door or window
is opened. Pressing the READY key will display the open protection points.
To turn Chime Mode on, enter your user code and press the CHIME key. The
CHIME message will appear.
To turn Chime Mode off, enter your user code and press the CHIME key again.
The CHIME message will disappear.
–29–
ACTIVATING A FIRE DRILL TEST
Using the
# + 6 + 9 Keys
This feature can be
activated only while the
burglary protection portion
of your system is disarmed
and no alarm, supervisory,
or trouble condition is
present.
Note: Only User Number 2's code can activate this test.
This test activates the external fire alarm sounders for the purpose of conducting a
fire alarm drill. Your system will remain operational for fire alarm signaling while this
test is active (although no message will be sent to the central station unless an
actual alarm occurs).
• To activate the Fire Drill Test:
Enter User Number 2's code, followed by the # + 6 + 9
keys.
The keypad LCD will display "FIRE DRILL ACTIVE (Alpha) or "TEST dF"
(Fixed-Word) and the external fire alarm sounders will produce either a steady or
a pulsing sound while this test is active, depending on what your installer
selected (see page 14).
FIRE DRILL
ACTIVE
ALPHA
dF
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
TAMPER
FIXED-WORD
• To terminate the Fire Drill Test:
Enter any User Code, followed by the OFF key.
Your system will also automatically terminate this test if an alarm, supervisory or
trouble condition is detected while it is activated.
–30–
ACTIVATING A BURGLARY WALK TEST
Using the
5 TEST Key
This feature can be
activated only while the
burglary protection portion
of your system is
disarmed.
Your fire alarm protection,
however, will remain active
during this test.
IF YOU FAULT A FIRE
ZONE, YOU WILL CAUSE
A FIRE ALARM!
Note: UL requires that this test be conducted weekly.
This test is used to check that sensors on all burglary and non-fire emergency
zones are operating properly.
• With the burglary protection disarmed, close all protected doors, windows, etc.
• To activate the Burglary Walk Test:
Enter any User Code, followed by the TEST key.
The external alarm sounders will sound for 1 second and then turn off. The
keypad LCD will display "BURGLARY WALK TEST IN PROGRESS" (Alpha)
or "TEST Cb" (Fixed-Word). The keypad buzzer will beep once every 10
seconds while this test is active.
BURGLARY WALK
TEST IN PROGRESS
ALPHA
C6
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
TAMPER
FIXED-WORD
• Open and close each protected door and window and walk in front of interior
motion detectors (if used). The keypad will beep 3 times each time a zone is
faulted and will display the number of the faulted zone while the fault remains.
After all protection points have been checked and restored, there should be no
zone numbers displayed. CALL YOUR INSTALLER IMMEDIATELY FOR
SERVICE IF YOU EXPERIENCE A PROBLEM! For servicing information, see
page 39.
• To terminate the Burglary Walk Test:
Enter any User Code, followed by the OFF key.
–31–
QUICK GUIDE TO SYSTEM FUNCTIONS
FUNCTION
PROCEDURE
COMMENTS
Check Faulted
Burglary Zones
Arm Burglary
Protection
Quick Arm
(if programmed)
Disarm Burglary
Protection
Silence Alarm,
Supervisory or
Trouble sounds
Clear Alarm Memory
Press READY key.
To view faulted zones when burglary protection not ready to arm.
Enter user code. Press desired arming key:
(AWAY, STAY, MAXIMUM, or INSTANT)
Press # key and desired arming key:
(AWAY, STAY, MAXIMUM or INSTANT)
Enter user Code + OFF key.
Arms burglary protection in selected mode.
Enter user Code + OFF key.
Also disarms system. Memory of fault condition remains until cleared.
Keypad displays # of faulted zone.
Re-enter user Code + OFF key.
Reset Smoke
Detectors & Displays
Manually Trip
Emergency Alarms
Re-enter user Code + OFF key.
Keypad will beep rapidly upon entry if alarm has occurred.
Alarm display will remain upon disarming until cleared.
Will reset only if fault corrected.
Trigger Duress Alarm
Bypass Burglary and
Emergency Zone(s)
Quick Bypass
(if programmed)
Fire Drill Test
Chime Mode
Burglary Walk Test
Assign, change, delete
user code.
Arms protection in selected mode without use of code.
Press key [A], [B], or [C] for at least 2 sec., or
Key(s) must be enabled by installer.
press keys [1]&[✱], or [✱]&[#], or [3]&[#],
both at same time.
Enter User Number 8's code when arming or disarming. Arms or disarms "normally" and sends a silent alarm message to central
station.
To bypass, enter user code + BYPASS key + zone
Bypassed zones are unprotected and will not cause an alarm if violated.
number(s) (use 2-digit entries).
To remove bypass, enter user code + OFF key.
Enter user code + BYPASS key.
Automatically bypasses all faulted burglary zones .
To activate: Enter User Number 2's code + # + 6 + 9.
To turn off: Enter any user code + OFF key.
To turn on: Enter user code + CHIME key.
To turn off: Re-enter user code + CHIME key.
To activate: Enter user code + TEST key.
To turn off: Enter user code + OFF key.
To assign or change: Enter User Number 2's code +
CODE key + user number (2–8) + new code.
–32–
Activates external fire alarm sounders.
Keypad beeps when protected doors or windows are opened.
Tests burglary alarm sounder and sensors.
To delete: Enter User 2's code + CODE key + user number (3–8) and
stop. Note: User Number 2 can change but not delete his/her own code.
SUMMARY OF AUDIBLE/VISUAL NOTIFICATION
ALPHA & FIXED-WORD DISPLAY KEYPADS
SOUND
CAUSE
DISPLAY (Fixed-Word displays are shown in parentheses)
SLOW PULSING Keypad
and, as selected by installer:
SLOW PULSING or
a. FIRE ALARM
b. FIRE DRILL
a. FIRE plus number and descriptor of zone in alarm (FIRE ALARM plus zone number).
b. FIRE DRILL ACTIVE (TEST dF)
a. BURGLARY or AUDIBLE
EMERGENCY ALARM
b. BURGLARY PROTECTION
EXIT ALARM (Exit or interior
burglary protection zone
faulted at time exit delay ends.)
(If programmed)
a. SUPERVISORY
b. TROUBLE, Fire or Day/Night
burglary zone problem
c. TROUBLE, System problem
a. ALARM plus number and descriptor of zone in alarm (ALARM plus zone number).
STEADY External,
STEADY
Keypad & External
RAPID PULSING Keypad
d. MEMORY OF ALARM
ONE SHORT BEEP
(not repeated), Keypad
STEADY SOUND, External,
for 1 second, then ONE
SHORT BEEP every 10
seconds from keypad.
TWO SHORT BEEPS,
Keypad
a. BURGLARY PROTECTION
DISARMING
b. BURGLARY PROTECTION
ARMING ATTEMPT WITH
AN OPEN ZONE
c. BYPASS VERIFICATION
b. •If burglary protection disarmed during subsequent entry delay period:
CANCELLED ALARM (CA). Sounds stop. No message sent to central station.
•If burglary protection not disarmed during subsequent entry delay period:
EXIT ALARM (EA). Sounds continue. Alarm message sent to central station.
a. SUPV plus number and descriptor of zone with SUPV condition (SUPV plus zone
number).
b. CHECK plus number and descriptor of zone (CHECK plus zone number).
c, AC LOSS (NO AC), or SYSTEM LOW BAT (BAT), or COMM FAILURE (FC)
when associated condition detected.
d. FIRE or ALARM plus # and descriptor of zone in alarm (FIRE and/orALARM plus zone #).
a. DISARMED/READY TO ARM (AC). Green READY indicator is lit.
b. FAULT plus number and descriptor of the faulted burglary protection zone (NOT READY
plus zone number). Green READY indicator is not lit.
SYSTEM IS IN BURGLARY
WALK TEST MODE
c. BYPASS plus numbers and descriptors of bypassed burglary protection zones (BYPASS
plus zone #'s). One beep for each zone displayed. Subsequently, the following is displayed:
DISARMED BYPASS READY TO ARM (BYPASS READY).
BURGLARY WALK TEST IN PROGRESS (TEST Cb).
Also,see "THREE SHORT BEEPS" below.
BURGLARY ARM ING, AWAY
OR MAXIMUM MODE
ARMED AWAY (AWAY) or ARMED MAXIMUM (AWAY INSTANT).
Red ARMED indicator is lit.
continued
–33–
SUMMARY OF AUDIBLE/VISUAL NOTIFICATION
ALPHA & FIXED-WORD DISPLAY KEYPADS
continued
SOUND
CAUSE
DISPLAY (Fixed-Word displays are shown in parentheses)
THREE SHORT BEEPS,
Keypad
a. BURGLARY PROTECTION
ARMING, STAY OR
INSTANT MODE
b. BURGLARY PROTECTION
ZONE FAULTED WHILE
SYSTEM IS IN CHIME MODE
c. BURGLARY PROTECTION
ZONE FAULTED WHILE SYSTEM IS IN BURGLARY WALK
TEST MODE
a. ENTRY DELAY WARNING
a. ARMED STAY (STAY) or ARMED INSTANT (STAY INSTANT).
Red ARMED indicator is lit.
SLOW BEEPING, Keypad
b. EXIT DELAY ALERT
(if programmed)
b. CHIME displayed. Pressing READY key will display zone FAULT plus # & descriptor
(zone #) of zone while faulted.
c.FAULT plus # and descriptor of the faulted burglary protection zone (NOT READY plus
zone #).
a. DISARM SYSTEM OR ALARM WILL OCCUR (no fixed-word display during entry).
Exceeding the delay time without disarming causes alarm.
b. ARMED AWAY (AWAY) or ARMED MAXIMUM (AWAY INSTANT).
Slow beeps change to fast during last 5 sec of exit delay.
–34–
PROTECTION ZONES LIST
One or more sensing devices will have been assigned by the installer of your alarm system to protection zones 01–05 in
your system. For example, fire sensing devices may have been assigned to zone 05, air conditioning temperature sensors
to zone 02, burglary protection sensing devices to zone 03, and so on.
Zone numbers 07, 95 and 96 represent Keypad "Emergency" alarm functions assigned by the installer (see Page 12).
Zone number 08 is reserved for Duress signal reporting to the central station. Zone numbers 06 and 10–13 report system
conditions.
This chart may be used to record the specific assignments for your system's zones 01–05, 07, 95 and 96. Your installer will
assist you in recording this information.
Zone
01*
02*
03*
04*
05*
06
07*
PROTECTION ZONE DESCRIPTIONS
Description
– Bell Supervision –
Keypad Emergency Key B (or ✱ & #)
08
10
11
12
13
95*
– Keypad Duress –
-Earth Ground Supervision– Main Dialer Supervision –
– Back-up Dialer Supervision –
– Auxiliary Relay Disable –
Keypad Emergency Key A (or 1 & ✱)
96*
Keypad Emergency Key C (or 3 & #)
* To be filled in
–35–
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following
statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with
the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to
comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are
designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user or
installer may find the following booklet prepared by the Federal Communications Commission helpful:
"Interference Handbook"
This booklet is available from the U.S. Government Printing Office, Washington, DC 20402.
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's
Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.
IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS
In the event of telephone operational problems, disconnect the control by removing the plug from the RJ31X wall jack. We recommend
that your certified installer demonstrate disconnecting the phones on installation of the system. Do not disconnect the phone
connection inside the control/communicator. Doing so will result in the loss of your phone lines. If the regular phone works correctly
after the control/communicator has been disconnected from the phone lines, the control/communicator has a problem and should be
returned for repair. If upon disconnection of the control/communicator, there is still a problem on the line, notify the telephone company
that they have a problem and request prompt repair service. The user may not under any circumstances (in or out of warranty) attempt
any service or repairs to the system. It must be returned to the factory or an authorized service agency for all repairs.
–36–
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 STATEMENT
This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains, among other
information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must
be provided to the telephone company.
This equipment uses the following jacks:
An RJ31X is used to connect this equipment to the telephone network.
The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the
telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs
should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total
RENs, contact the telephone company to determine the maximum REN for the calling area.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon
as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of
the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary
modifications in order to maintain uninterrupted service.
If trouble is experienced with this equipment, please contact the manufacturer for repair and warranty information. If the trouble is
causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the
problem is resolved.
There are no user serviceable components in this product, and all necessary repairs must be made by the manufacturer. Other repair
methods may invalidate the FCC registration on this product.
This equipment cannot be used on telephone company-provided coin service. Connection to Party Line Service is subject to state
tariffs.
This equipment is hearing-aid compatible.
When programming or making test calls to an emergency number, briefly explain to the dispatcher the reason for the call. Perform
such activities in the off-peak hours; such as early morning or late evening.
–37–
WARNING!
THE LIMITATIONS OF THIS ALARM SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or other
emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons.
For example:
• Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or
disconnect an alarm warning device.
• Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work without power.
Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices
powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly.
• Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal
path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path.
• A user may not be able to reach a panic or emergency button quickly enough.
• While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or
provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency
Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows.
Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke
cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may
not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or
basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In
general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent
explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or
arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as
anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death.
• Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual.
Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can
only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind
walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying
of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared
Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range
of 90° to 105°F (32° to 40°C), the detection performance can decrease.
(continued)
–38–
WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM
(continued)
• Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of
closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less
likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled
from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not
warn hearing-impaired people or waken deep sleepers.
• Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily
out of service. Telephone lines are also subject to compromise by sophisticated intruders.
• Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves
from the situation. In the case of a monitored alarm system, authorities may not respond appropriately.
• This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long
as 10 years, the electronic components could fail at any time.
The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm
system should be tested weekly to make sure all sensors and transmitters are working properly.
Wireless transmitters (used with some systems) are designed to provide long battery life under normal operating conditions. Longevity
of batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device being used.
External factors such as humidity, high or low temperatures, as well as large swings in temperature, may all reduce the actual battery
life in a given installation. This wireless system, however, can identify a true low battery situation, thus allowing time to arrange a
change of battery to maintain protection for that given point within the system.
Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance.
Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives
and property.
We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to
learn about these developments.
SERVICING INFORMATION
Your local authorized service representative is the person best qualified to service your alarm system. Arranging a
regular program with that person is advisable. Your local service representative is:
NAME: _____________________________________________PHONE: __________________________
ADDRESS: ______________________________________________________________________________
______________________________________________________________________________
–39–
ADEMCO ONE YEAR LIMITED WARRANTY
Alarm Device Manufacturing Company, a Division of Pittway Corporation, and its divisions, subsidiaries and affiliates ("Seller"), 165
Eileen Way, Syosset, New York 11791, warrants its security equipment (the "product") to be free from defects in materials and
workmanship for one year from date of original purchase, under normal use and service. Seller's obligation is limited to repairing or
replacing, at its option, free of charge for parts, labor, or transportation, any product proven to be defective in materials or
workmanship under normal use and service. Seller shall have no obligation under this warranty or otherwise if the product is altered or
improperly repaired or serviced by anyone other than the Seller. In case of defect, contact the security professional who installed and
maintains your security equipment or the Seller for product repair.
This one year Limited Warranty is in lieu of all other express warranties, obligations or liabilities. THERE ARE NO EXPRESS
WARRANTIES, WHICH EXTEND BEYOND THE FACE HEREOF. ANY IMPLIED WARRANTIES, OBLIGATIONS OR LIABILITIES MADE
BY SELLER IN CONNECTION WITH THIS PRODUCT, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, OR FITNESS
FOR A PARTICULAR PURPOSE OR OTHERWISE, ARE LIMITED IN DURATION TO A PERIOD OF ONE YEAR FROM THE DATE OF
ORIGINAL PURCHASE. ANY ACTION FOR BREACH OF ANY WARRANTY, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY, MUST BE BROUGHT WITHIN 12 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE
SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY
OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR
DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. Some states do not allow limitation on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply
to you.
Seller does not represent that the product may not be compromised or circumvented; that the product will prevent any personal injury or
property loss by burglary, robbery, fire or otherwise; or that the product will in all cases provide adequate warning or protection. Buyer
understands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery, fire or other events
occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury
or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY
DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR
OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE
PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state. No increase or alteration,
written or verbal, to this warranty is authorized.
A Division of Pittway Corporation
165 Eileen Way, Syosset, New York 11791
N8031 6/96
Copyright © 1996 PITTWAY CORPORATION
–40–
Download PDF
Similar pages