N045157 man drill D21716 GB.indd

www.
.eu
D21716
D21717
1
Copyright DEWALT
2
A
7
8
9
5
4
11
3 1 2
6
5
4
13
10
9
7
11
8
6
3 1 2
1
B
4
D
C
7
6
2
E
12
F
12
3
ENGLISH
PERCUSSION DRILL
D21716, D21717
Congratulations!
You have chosen a DEWALT Power Tool. Years of
experience, thorough product development and
innovation make DEWALT one of the most reliable
partners for professional Power Tool users.
Technical Data
Voltage
(U.K. & Ireland only)
Type
Power input
No-load speed
No load impact
Maximum drilling range in
steel/wood/concrete
Chuck spindle
thread size
Collar diameter
Maximum chuck
capacity
Weight
LPA (sound pressure)
KPA (sound pressure
uncertainty K)
LWA (sound power)
KWA (sound power
uncertainty K)
W
min-1
min-1
D21716
D21717
230
230/115
2
701
0 - 2,600
0 - 44,200
mm
13/30/16
UNF
mm
1/2" x 20
43
mm
kg
13
1.9
dB(A)
95
dB(A)
dB(A)
3.1
106
dB(A)
3.1
V
V
Vibration emission value ah
Drilling into Metal:
ah,D =
m/s²
Uncertainty K =
m/s²
Vibration emission value ah
Screwdriving:
ah =
m/s²
Uncertainty K =
m/s²
4
WARNING: The declared vibration
emission level represents the main
applications of the tool. However if the
tool is used for different applications,
with different accessories or poorly
maintained, the vibration emission may
differ. This may significantly increase the
exposure level over the total working
period.
An estimation of the level of exposure to
vibration should also take into account
the times when the tool is switched off or
when it is running but not actually doing
the job. This may significantly reduce
the exposure level over the total working
period.
Identify additional safety measures to
protect the operator from the effects of
vibration such as: maintain the tool and
the accessories, keep the hands warm,
organisation of work patterns.
Fuses:
Europe
U.K. & Ireland
U.K. & Ireland
230 V tools 10 Amperes, mains
230 V tools 13 Amperes, in plugss
115 V tools
16 Amperes, mains
Definitions: Safety Guidelines
The definitions below describe the level of severity for
each signal word. Please read the manual and pay
attention to these symbols.
Vibration total values (triax vector sum) determined
according to EN 60745:
Vibration emission value ah
Hammerdrilling:
ah,ID =
m/s²
Uncertainty K =
m/s²
The vibration emission level given in this information
sheet has been measured in accordance with a
standardised test given in EN 60745 and may be
used to compare one tool with another. It may be
used for a preliminary assessment of exposure.
22.9
2.9
2.8
1.5
< 2.5
1.5
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not avoided,
may result in minor or moderate
injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
ENGLISH
b)
Denotes risk of electric shock.
Denotes risk of fire.
c)
EC-Declaration of Conformity
MACHINERY DIRECTIVE
D21716, D21717
DEWALT declares that these products described
under “technical data” are in compliance with:
98/37/EC (until Dec. 28, 2009), 2006/42/EC
(from Dec. 29, 2009), EN 60745-1, EN 60745-2-1,
EN60745-2-2.
These products also comply with Directive 2004/108/
EC. For more information, please contact DEWALT
at the following address or refer to the back of the
manual.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
DEWALT.
Horst Grossmann
Vice President Engineering and Product Development
DEWALT, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
06.08.2009
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and instructions Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or batteryoperated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body
is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply. Use
of an RCD reduces the risk of electric shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes,
hard hat, or hearing protection used for
appropriate conditions will reduce personal
injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with your finger on the
5
ENGLISH
d)
e)
f)
g)
switch or energising power tools that have the
switch on invites accidents.
Remove any adjusting key or wrench
before turning the power tool on. A wrench
or a key left attached to a rotating part of the
power tool may result in personal injury.
Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in unexpected
situations.
Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in
moving parts.
If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dustrelated hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application. The
correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power
tool before making any adjustments,
changing accessories, or storing power
tools. Such preventive safety measures
reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the working
6
conditions and the work to be performed.
Use of the power tool for operations different
from those intended could result in a
hazardous situation.
5) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Specific Safety Rules
for Drills
•
•
•
•
•
•
Wear ear protectors. Exposure to noise can
cause hearing loss.
Hold power tool by insulated gripping
surfaces only, when performing an
operation where the cutting accessory
may contact hidden wiring or its own cord.
Cutting accessory contacting a “live” wire may
make exposed metal parts of the power tool
“live” and shock the operator.
Use clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand or
against your body is unstable and may lead to
loss of control.
Wear safety goggles or other eye
protection. Drilling operations cause chips to
fly. Flying particles can cause permanent eye
damage.
Bits and tools get hot during operation.
Wear gloves when touching them.
Keep handles dry, clean, free from oil and
grease. it is recommended to use rubber
gloves. This will enable better control of the
tool.
Residual Risks
The following risks are inherent to the use of drills:
– Injuries caused by touching the rotating parts or
hot parts of the tool.
In spite of the application of the relevant safety
regulations and the implementation of safety devices,
certain residual risks cannot be avoided. These are:
– Impairment of hearing.
– Risk of squeezing fingers when changing
accessories.
– Health hazards caused by breathing dust
developed when working in wood.
– Risk of personal injury due to flying particles.
– Risk of personal injury due to prolonged use.
ENGLISH
Markings on Tool
The following pictograms are shown on the tool:
DO NOT use under humid conditions or in presence
of flammable liquids or gases.
DATE CODE POSITION (FIG. A)
These percussion drills are professional power tools.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators
use this tool.
The Date Code (13), which also includes the year of
manufacture, is printed into the housing.
Electrical Safety
Read instruction manual
before use.
Example:
2009 XX XX
Year of Manufacture
Package Contents
The package contains:
1 Percussion drill
1 Side handle
1 Depth gauge
1 Chuck key (D21716)
1 Kitbox (K-models only)
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories
which may have occurred during transport.
• Take the time to thoroughly read and understand
this manual prior to operation.
Description (fig. A, E)
WARNING: Never modify the power
tool or any part of it. Damage or personal
injury could result.
1
2
3
4
5
6
7
8
8
9
10
11
12
Variable speed switch
Lock-on button
Forward/reverse slider
Mode selector
Ventilation slots
Side handle
Depth adjustment rod
Keyed chuck (D21716)
Keyless chuck (D21717)
Sleeve
Chuck key
Main handle
Screw
INTENDED USE
Your percussion drill has been designed for
professional drilling and screwdriving applications.
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your DEWALT tool is double insulated in
accordance with EN 60745; therefore no
earth wire is required.
WARNING: 115 V units have to
be operated via a fail-safe isolating
transformer with an earth screen between
the primary and secondary winding.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DEWALT service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the
plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made
to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor size
is 1 mm2; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENT
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-ups
or when making repairs. Be sure the
7
ENGLISH
trigger switch is in the OFF position. An
accidental start-up can cause injury.
Selecting the Operating Mode (fig. B)
The tool can be used in two operating modes:
Rotary drilling:
for steel, wood and plastics.
Percussion drilling:
simultaneous rotating and impacting for
concrete and masonry drilling operations.
• Select the required operating mode by rotating
the mode selector (4) to the required position.
Inserting and Removing a Bit (fig. A)
Keyless chuck
• Open the chuck by turning the sleeve (9)
counterclockwise and insert the bit shank.
• Tighten firmly by turning the sleeve clockwise.
Keyed Chuck
• Open the chuck by turning the sleeve (9)
counterclockwise and insert the bit shank.
• Put the chuck key (10) into each hole in the side
of the chuck and turn clockwise until tight.
• To remove the bit, proceed in reverse order.
Fitting the Side Handle (fig. A)
The side handle (6) can be fitted to suit both
RH- and LH-users.
WARNING: Always use the drill with the
side handle properly assembled.
• Loosen the side handle.
• For RH-users, slide the side handle clamp over
the collar behind the chuck, handle at the left.
• For LH-users, slide the side handle clamp over
the colar behind the chuck, handle at the right.
• Rotate the side handle to the desired position
and tighten the handle.
Setting the Drilling Depth (fig. C)
• Insert the required drill bit into the chuck.
• Slacken the side handle (6).
• Fit the depth adjustment rod (7) through the hole
in the side handle clamp.
8
• Adjust the drilling depth as shown.
• Tighten the side handle.
Forward/reverse Slider (fig. A)
• To select forward or reverse rotation, use the
forward/reverse-switch (3) (see arrow on tool).
WARNING: Always wait until the motor
has come to a complete standstill before
changing the direction of rotation.
Chuck Removal (fig. E, F)
• Open the chuck jaws as far as possible.
• Insert a screwdriver into the chuck and remove
the chuck retaining screw (12) by turning
clockwise.
• Tighten an Allen key into the chuck and strike it
with a hammer as shown.
Prior to Operation
• Insert the appropriate bit.
• Mark the spot where the hole is to be drilled.
OPERATION
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
Instructions for Use
WARNING:
• Always observe the safety instructions
and applicable regulations.
• Be aware of the location of pipework
and wiring.
• Apply only a gentle pressure to the tool.
Excessive force does not speed up
drilling but decreases tool performance
and may shorten tool life.
Proper Hand Position (fig. A, D)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper
hand position as shown.
ENGLISH
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the side
handle (6), with the other hand on the main handle
(11).
Switching On and Off (fig. A)
• To run the tool, press the variable speed switch (1).
The pressure exerted on the variable speed switch
determines the tool speed.
• If necessary, press the lock-on button (2) for
continuous operation and release the switch.
The lock-on button works only in full speed,
forward rotation.
• To stop the tool, release the switch.
• To stop the tool in continuous operation, press
the switch briefly and release it. Always switch
off the tool when work is finished and before
unplugging.
Screwdriving
• Select forward or reverse rotation.
Percussion Drilling (fig. A)
• Select the percussion mode.
• Press the switch (1).
Rotary Drilling (fig. A)
• Select the rotary drilling mode.
• Proceed as described for percussion drilling.
Drilling
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
WARNING: To reduce the risk of
personal injury, ALWAYS ensure
workpiece is anchored or clamped firmly.
If drilling thin material, use a wood “backup” block to prevent damage to the
material.
1. Use sharp drill bits only. For WOOD, use the
low speed setting and twist drill bits, spade bits,
power auger bits, or hole saws. For METAL, use
the low speed setting and steel twist drill bits or
hole saws.
2. Always apply pressure in a straight line with the
bit. Use enough pressure to keep drill biting, but
do not push hard enough to stall the motor or
deflect the bit.
3. Hold tool firmly with both hands to control the
twisting action of the drill.
CAUTION: Drill may stall if overloaded
causing a sudden twist. Always expect
the stall. Grip the drill firmly to control the
twisting action and avoid injury.
4. IF DRILL STALLS, it is usually because it is
being overloaded or improperly used. RELEASE
TRIGGER IMMEDIATELY, remove drill bit
from work, and determine cause of stalling. DO
NOT CLICK TRIGGER ON AND OFF IN AN
ATTEMPT TO START A STALLED DRILL —
THIS CAN DAMAGE THE DRILL.
5. To minimize stalling or breaking through the
material, reduce pressure on drill and ease the bit
through the last fractional part of the hole.
6. Keep the motor running when pulling the bit
back out of a drilled hole. This will help prevent
jamming.
7. With variable speed drills there is no need to
center punch the point to be drilled. Use a
slow speed to start the hole and accelerate by
squeezing the trigger harder when the hole is
deep enough to drill without the bit skipping out.
DRILLING IN METAL
Start drilling with slow speed and increase to full
power while applying firm pressure on the tool. A
smooth even flow of metal chips indicates the proper
drilling rate. Use a cutting lubricant when drilling
metals. The exceptions are cast iron and brass which
should be drilled dry.
NOTE: Large [5/16" (8 mm) to 1/2" (13 mm)] holes in
steel can be made easier if a pilot hole [5/32"
(4 mm) to 3/16" (5 mm)] is drilled first.
DRILLING IN WOOD
Start drilling with slow speed and increase to full
power while applying firm pressure on the tool. Holes
in wood can be made with the same twist drills used
for metal. These bits may overheat unless pulled out
frequently to clear chips from the flutes. Work that is
apt to splinter should be backed up with a block of
wood.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
9
ENGLISH
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-ups
or when making repairs. Be sure the
trigger switch is in the OFF position. An
accidental start-up can cause injury.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of the
main housing with dry air as often as dirt
is seen collecting in and around the air
vents. Wear approved eye protection and
approved dust mask when performing
this procedure.
WARNING: Never use solvents or other
harsh chemicals for cleaning the nonmetallic parts of the tool. These chemicals
may weaken the materials used in these
parts. Use a cloth dampened only with
water and mild soap. Never let any liquid
get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other
than those offered by DEWALT, have not
been tested with this product, use of
such accessories with this tool could be
hazardous. To reduce the risk of injury,
only DEWALT, recommended accessories
should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
10
Should you find one day that your DEWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products and
packaging allows materials to be recycled
and used again. Re-use of recycled
materials helps prevent environmental
pollution and reduces the demand for
raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at municipal
waste sites or by the retailer when you purchase a
new product.
DEWALT provides a facility for the collection and
recycling of DEWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest authorised
repair agent by contacting your local DEWALT office
at the address indicated in this manual. Alternatively, a
list of authorised DEWALT repair agents and full details
of our after-sales service and contacts are available
on the Internet at: www.2helpU.com.
ENGLISH
GUARANTEE
DEWALT is confident of the quality of its
products and offers an outstanding guarantee
for professional users of the product. This
guarantee statement is in addition to and in
no way prejudices your contractual rights as a
professional user or your statutory rights as a
private non-professional user. The guarantee is
valid within the territories of the Member States
of the European Union and the European Free
Trade Area.
• 30 DAY NO RISK
SATISFACTION GUARANTEE •
If you are not completely satisfied with the
performance of your DEWALT tool, simply return
it within 30 days, complete with all original
components, as purchased, to the point of
purchase, for a full refund or exchange. The
product must have been subject to fair wear and
tear and proof of purchase must be produced.
• ONE YEAR FREE SERVICE CONTRACT •
If you need maintenance or service for your
DEWALT tool, in the 12 months following
purchase, it will be undertaken free of charge
at an authorised DEWALT repair agent. Proof of
purchase must be produced. Includes labour.
Excludes accessories and spare parts unless
failed under warranty.
• ONE YEAR FULL WARRANTY •
If your DEWALT product becomes defective
due to faulty materials or workmanship within
12 months from the date of purchase, DEWALT
guarantees to replace all defective parts free of
charge or – at our discretion – replace the unit
free of charge provided that:
• The product has not been misused;
• The product has been subject to fair wear
and tear;
• Repairs have not been attempted by
unauthorised persons;
• Proof of purchase is produced;
• The product is returned complete with all
original components.
If you wish to make a claim, contact your seller
or check the location of your nearest authorised
DEWALT repair agent in the DEWALT catalogue
or contact your DEWALT office at the address
indicated in this manual. A list of authorised
DEWALT repair agents and full details of our
after-sales service is available on the Internet at:
www.2helpU.com.
11
12
13
Belgique et Luxembourg
België en Luxemburg
Black & Decker - DEWALT
Nieuwlandlaan 7, IZ Aarschot B156
B-3200 Aarschot
Tel:
+32 (0)015 - 15 47 9211
Fax:
+32 (0)015 - 15 47 9210
www.dewalt.be
Danmark
DEWALT
Sluseholmen 2-4
2450 København SV
Tlf:
70201511
Fax:
70224910
www.dewalt.dk
Deutschland
DEWALT
Richard-Klinger-Straße
65510 Idstein
Tel:
06126-21-1
Fax:
06126-21-2770
www.dewalt.de
Ελλάς
Black & Decker (Hellas) S.A.
Στράβωνος 7 & Βουλιαγμένης 159
Γλυφάδα 16674, Αθήνα
Τηλ:
(01) 8981-616
Φαξ:
(01) 8983-570
Service: (01) 8982-630
España
DEWALT
Parque de Negocios “Mas Blau”
Edificio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
Tel:
934 797 400
Fax:
934 797 439
www.dewalt.es
France
DEWALT
5, allée des hêtres
BP 30084, 69579 Limonest Cedex
Tel:
04 72 20 39 20
Fax:
04 72 20 39 00
www.dewalt.fr
Schweiz
Suisse
Svizzera
DEWALT
In der Luberzen 40
8902 Urdorf
Tel:
01 - 730 67 47
Fax:
01 - 730 70 67
www.dewalt.ch
Ireland
DEWALT
Calpe House Rock Hill
Black Rock, Co. Dublin
Tel:
00353-2781800
Fax:
00353-2781811
www.dewalt.ie
Italia
DEWALT
Viale Elvezia 2
20052 Monza (Mi)
Tel:
800-014353
Fax:
039-2387592
www.dewalt.it
Nederlands
Black & Decker - DEWALT
Joulehof 12
4600 AB Bergen Op Zoom
Tel:
0164 283000
Fax:
0164 283100
www.dewalt.nl
Norge
DEWALT
Postboks 4814, Nydalen
0422 Oslo
Tel:
22 90 99 00
Fax:
22 90 99 01
www.dewalt.no
Österreich
DEWALT
Werkzeugevertriebs GmbH
Erlaaerstraße 165, Postfach 320,1231 Wien
Tel:
01 - 66116 - 0
Fax:
01 - 66116 - 14
www.dewalt.at
Portugal
DEWALT
Rua Egas Moniz 173
João do Estoril, 2766-651 Estoril
Tel:
214 66 75 00
Fax:
214 66 75 75
www.dewalt.pt
Suomi
DEWALT Oy
Tekniikantie 12
02150 Espoo, Finland
Puh:
010 400 430
Faksi: 0800 411 340
www.dewalt.fi
DEWALT Oy
Teknikvägen 12
02150 Esbo, Finland
Tel:
010 400 430
Fax:
0800 411 340
www.dewalt.fi
Sverige
DEWALT
Box 94
431 22 Mölndal
Tel:
031 68 61 00
Fax:
031 68 60 08
www.dewalt.se
Türkiye
KALE Hırdavat ve Makina A.Ş.
Defterdar Mah. Savaklar Cad. No:15
Edirnekapı / Eyüp / İSTANBUL 34050 TÜRKİYE
Tel:
0212 533 52 55
Faks: 0212 533 10 05
www.dewalt.com.tr
United Kingdom
DEWALT
210 Bath Road
Slough, Berks SL1 3YD
Tel:
01753-56 70 55
Fax:
01753-57 21 12
www.dewalt.co.uk
N045157
10/09
Download PDF
Similar pages