Pointillés / Blitz Studio
USER GUIDE
Get Videofied,
visit us at
www.videofied.com
English
p. 1-12
We recommend that you read this user manual carefully to ensure that your security system is
operated with maximum efficiency and in optimal conditions.
The VIDEOFIED® system complies with European radio standards and is designed to operate in
frequency ranges which are not harmful to the user.
Arming - Away1-2
Arming - Stay2
Disarming - Off3-4
Activating Emergency Requests4
Activate/Deactivate Chime4
Partition Arming5-6
Partition Disarming6-7
Checking System Status7
Direct Device Bypass8
Activating Duress Signals8-9
Managing Badges and Codes9-11
Notes12
ENGLISH
Arming - Away
1. Keypad (XMA/WMB)
Code Arming (XMA/WMB):
 Enter access code and press
 The keypad display will show
Quick Arm (XMA/WMB):
 Press and hold
to confirm.
ARMING THE
SYSTEM
until the keypad rapdily beeps three times.
 The keypad display will show
or
SYSTEM ARMING
AWAY
Keypad Badge Reader (WMB):
 Present the badge to the
symbol on the keypad and hold it for 2 seconds.
 The keypad beeps once and shows a green LED to confirm.
 The keypad display will show
ARMING THE
SYSTEM
Note: Detection from an instant device during arming will stop the arming process and display "DEVICE
DETECTION
. Press
to restart the arming process or
NAME"
to bypass the device. If no command is registered the system will automatically restart arming after 3 minutes.
 For all keypad arming options the exit delay starts and short beeps are emitted from the keypad and internal sirens (if installed). At the end of the exit delay the display SYSTEM ARMED shows and the LED on the keypad flashes RED ever two seconds.
3. Remote Control
 Press the
button and instantly release.
 The remote control will beep twice in confirmation.
Note: A single low tone notifies the command was not received at the control apnel. Move closer to the control panel and reattempt to arm the system.
 The exit delay starts and short beeps are emitted from the Remote Control and internal sirens (if installed)
1
2. Badge Reader (BR)
 Present the badge to the reader and hold for two (2) seconds.
 The reader will beep twice in acknowledgement.
 One red and one green LED will display on the reader and the exit delay will start.
Note: Detection from an instant device or if there is a problem with arming the reader will display two green LEDs for 5 seconds. Without action from the user the system will attempt rearming in 3 minutes.
 Short beeps are emitted from the reader and internal sirens (if installed). At the end of the time delay the system is armed and the red LED on the reader flashes every two seconds.
Arming - Stay
1. Keypad (XMA/WMB)
Code Arming (XMA/WMB):
 Enter access code and press
 The keypad display will show
Quick Arm (XMA/WMB):
 Press and hold
until the keypad rapdily beeps three times.
 The keypad display will show
ARMING
SP1
SYSTEM ARMING
SP1
Keypad Badge Reader (WMB):
 Press the
. Keypad will display
 Present the badge to the
ALARM SP1
BADGE OR CODE
symbol on the keypad and hold it for 2 seconds.
 The keypad beeps once and shows a green LED to confirm.
 The keypad display will show
ARMING
SP1
Note: Detection from an instant device during arming will stop the arming process and display "DEVICE
DETECTION
. Press
to restart the arming process or
NAME"
to bypass the device. If no command is registered the system will automatically restart arming after 3 minutes.
 For all keypad arming options the exit delay starts and short beeps are emitted from the keypad and internal sirens (if installed). At the end of the exit delay the display SYSTEM ARMED shows and the LED on the keypad flashes RED ever two seconds.
2
ENGLISH
Arming - Away Continued...
Disarming - Off
1. Keypad (XMA/WMB)
No Event:
Code Disarming (XMA/WMB)
 Enter access code and press
 The keypad display will show
or
to confirm.
Mon 01/02 04:49
DISARMED LVL:1
Quick Disarm (XMA/WMB):
 Press and hold
until the keypad rapdily beeps three times.
 The keypad display will show
DISARMING
BADGE OR CODE
 Enter access code and press
 The keypad display will show
Mon 01/02 04:49
DISARMED LVL:1
Keypad Badge Reader (WMB):
 Present the badge to the
symbol on the keypad and hold it for 2 seconds.
 The keypad beeps once and shows a green LED to confirm.
 The keypad display will show
Mon 01/02 04:49
DISARMED LVL:1
Event Acknowledgment: During disarming you must acknowledge any events that have happened since the system was last armed.
 Perform any of the above disarming options
 The keypad display will show
 Press
to acknowledge that the event has occured since last arming
 The keypad display will show
 Press
"Event"
, display will show
"Event"
"Device Name"
Mon 01/02 04:49
DISARMED LVL:1
2. Remote Control (RC)
 Press the
button and instantly release after the first beep
 The remote control will beep twice in confirmation
Note: A single low tone notifies the command was not recieved at the control panel. Move closer to the control panel and reattempt to disarm the system.
 The system is disarmed.
3
ENGLISH
Disarming - Off - Continued
3. Badge Reader (BR)
 Present the badge to the reader and hold for 2 seconds.
 The reader will beep twice in acknowledgement.
No Event:
Event Acknowledgment:
 Two green LEDs will light up and the system is disarmed.
 The top LED will blink twice and the reader will beep 4 times to indicate an event has occured since the last arming.
 The system is disarmed.
Activating Emergency Requests
Medical Emergency
Police Emergency
1. Keypad (XMA/WMB)
Fire Emergency
 Press the
 They Keypad display flashes
 Press the desired emergency button.
 Display shows
button for 3 seconds.
for 10 seconds.
POLICE
BADGE OR CODE
 A valid user code or badge for the system must be used to clear the event.
Activate/Deactivate Chime
*The chime function will only sound through an indoor siren that is learned into the
system*
1. Keypad (XMA/WMB)
4
 Press and hold the
three times.
 They display will show
button until the keypad beeps rapidly CHIME
ACTIVATED
CHIME
or DEACTIVATED
.
Partition Arming
1. Keypad (XMA/WMB)
Code Partition Arming (XMA/WMB)
 Press
until the desired partition is shown
 Enter a user code and press
 The system displays
ARMING
A A - -
Note: Detection from an instant device during arming will stop the arming process and DETECTION
display. "DEVICE
You may press
to retry the arming or
to bypass the device. NAME"
If no command is registered the system will automatically retry arming after 3 minutes.
 The exit delay starts and short beeps are emitted from the keypad and internal sirens (if installed). At the end of the exit delay the red LED on the keypad flashes every two seconds.
Keypad Badge Reader Partition Arming (WMB):
 Press
until the desired partition is shown
 Present the badge to the
seconds.
symbol on the keypad and hold it for 2  The keypad beeps once and shows a green LED to confirm.
 The keypad display will show
ARMING
A A - -
Note: Detection from an instant device during arming will stop the arming process and display "DEVICE
DETECTION
. Press
to restart the arming process or
NAME"
to bypass the device. If no command is registered the system will automatically restart arming after 3 minutes.
 For all keypad arming options the exit delay starts and short beeps are emitted from the keypad and internal sirens (if installed). At the end of the exit delay the display shows what partitions and what mode Thu 05/13 14:24
they have been armed in PA1=A
PA2=A L:1s and the LED on the keypad flashes RED ever two seconds.
2. Remote Control (RC)
Note: Remote Controls are configured during installation to use specfic partitions. There is no option to
choose which partition to arm on the Remote Control.
 Press the
 The remote control will beep twice in confirmation and the exit delay starts.
button and instantly release.
Note: A single low tone notifies the command was not recieved at the control panel. Move closer to the control panel and reattempt to disarm the system.
 The system is armed for the parition(s) the device is set.
5
ENGLISH
Partition Arming - Continued
3. Badge Reader (BR)
Note: Badges are configured during installation to use specfic partitions. There is no option to
choose which partition to arm with the Badge Reader.
 Present the badge to the reader and hold for two (2) seconds.
 The reader will beep twice in acknowledgement.
 One red and one green LED will display on the reader and the exit delay will start.
Note: Detection from an instant device or if there is a problem with arming the reader will display two green LEDs for 5 seconds. Without action from the user the system will attempt rearming in 3 minutes.
 Short beeps are emitted from the reader and internal sirens (if installed). At the end of the time delay the system is armed and the red LED on the reader flashes every two seconds.
Partition Disarming
1. Keypad (XMA/WMB)
No Event:
Partition Code Disarming (XMA/WMB)
 Press
until the desired partition to be disarmed is shown
 Enter access code and press
 The keypad display will show
or
to confirm.
Mon 01/02 04:49
DISARMED LVL:1
Keypad Badge Reader Partition Disarming (WMB)
 Press
until the desired partition to be disarmed is shown
 Present the badge to the
seconds.
symbol on the keypad and hold it for 2  The keypad beeps once and shows a green LED to confirm.
 The keypad display will show
Mon 01/02 04:49
DISARMED LVL:1
Event Acknowledgment: During disarming you must acknowledge any events that have happened since the system was last armed.
 Perform any of the above disarming options
 The keypad display will show
 Press
to acknowledge that the event has occured since last arming
 The keypad display will show
 Press
6
"Event"
, display will show
"Event"
"Device Name"
Mon 01/02 04:49
DISARMED LVL:1
Partition Disarming - Continued
2. Remote Control (RC)
Note: Remote Controls are configured during installation to use specfic partitions. There is no option to choose
which partition to disarm on the Remote Control.
 Press the
 The remote control will beep twice in confirmation
button and instantly release.
Note: A single low tone notifies the command was not recieved at the control panel. Move closer to the control panel and reattempt to disarm the system
 The system is disarmed for the parition(s) the device is set
3. Badge Reader (BR)
Note: Badges are configured during installation to use specfic partitions. There is no option to
choose which partition to disarm on the Badge Reader.  Present the badge to the reader and hold for two (2) seconds
 The reader will beep twice in acknowledgement
 Two green LEDs will light up and the system will be disarmed
Event Acknowledgment: Perform the above steps and the top LED will blink
twice and the reader will beep 4 times to indicate that there has been an event
since arming and then system will be disarmed.
Checking System Status
1. Keypad (XMA/WMB)
 Press and hold the
three times
 The display will show devices that are in trouble, communication methods that are enabled but have problems or that the system is Ready To Arm if no faults are found. Use the arrow keys to scroll through all devices that
are in trouble or press
DEVICE TAMPER
SUPERVISION
PROBLEM
SUPERVISION
PROBLEM
to exit back to the main screen
There are no Faults found
READY TO ARM
ETHERNET BAD
button until the keypad beeps rapidly 2G3G BAD
Issue with the communication method
Displayed device is in tamper
Displayed device is not communicating with the
control panel
The listed detector is currently open
7
1. Keypad (XMA/WMB)
 Press and hold the
rapidly three times
 The display will show
button until the keypad beeps BADGE OR CODE
for 10 seconds
 Enter a user code for the system followed by
 Use the arrow keys to find the device you would like to
bypass and press
 Repeat the steps above until all desired devices have been set to be bypassed
 Selected devices will be bypassed on the next arming. If the system is not armed in the next 24 hours the devices will return to "Not Bypassed"
 When arming with any number of devices set to be BYPASS
bypassed the display will read ARMING
SYSTEM
Activating Duress Signals
1. Keypad (XMA/WMB)
Note: Duress codes are automatically set by the system when a code is added.
 For an audible Duress enter a 4-6 digit user code with 2 numbers higher than the actual code
 For a silent Duress enter a 4-6 digit user code with 1 number higher than the actual code
Example 1:
User code is set to: 1234
Audible Duress:
1236
Silent Duress:
1235
Example 2:
User code is set to: 123456
Audible Duress:
123458
Silent Duress:
123457
8
ENGLISH
Direct Device Bypass
Activating Duress Signals - Continued
2. Remote Control (RC)
Audible Duress
 Press the

button and hold for 4 seconds.
The remote control will beep twice in confirmation and all sounders will begin
Note: A single low tone notifies the command was not recieved at the control panel.
Silent Duress
 Press the

button and hold for 4 seconds.
The remote control will beep twice in confirmation
Note: A single low tone notifies the command was not recieved at the control panel.
Managing Badges / Access Codes
1. Keypad (XMA/WMB)
Note: Badges and codes can only entered into the system by a Level 3 user code
Accessing Level 3 Programming (XMA/WMB)
 The display will read
 Press the DATE/TIME
DISARMED LVL 1
until the display reads
 Press
and use the  Press
. Display will show
to move the level to 3
BADGE OR CODE
 Enter a valid level 3 code followed by
to the
for 2 seconds.
 The display will show
ACCESS LEVEL 1
or present a level 3 badge ACCESS LEVEL 3
 The system will automatically default back to ACCESS LEVEL 1 after 60 seconds of inactivity.
9
ENGLISH
Managing Badges / Access Codes - Continued
Adding Badges/Codes (XMA/WMB)
Note: Badges require WMB or BR badge reader learned into the system.
 Perform 'Accessing Level 3 Programming' and verify you are in Access Level 3
 Press until the display reads
 Press
. Display will show
 Press
. Display will show
BADGES AND
ACCESS CODES
ENTER A
BADGE / CODE
BADGE / CODE
Adding a Code:
 Enter a 4-6 digit user code and press
 The display will show
CONFIRM THE CODE
 Re-enter the 4-6 digit code and press
 The display will show
NAME OF CODE
 Enter a name for the code or leave it blank and press
 The code has now been entered into the system
Note: When a code is created the system will automaticaly generate two sub-codes that
can be used as a silen and audible duress. This means that for every code you create you
will not be able to create another code withing +/- 2 digits.
Example: Code 1234 has been created. 1235, 1236, 1233, 1232 are no longer available
Adding a Badge:
 Present the Badge to the
seconds
or BR Reader for 2  The reader will beep and the display will change to
NAME OF BADGE
 Enter a name for the badge or leave it blank and press
10
Managing Badges / Access Codes - Continued
Deleting Badges/Codes (XMA/WMB)
 Perform 'Accessing Level 3 Programming' and verify you are in Access Level 3
 Press the  Press
until the display reads
and use the to move to
BADGES AND
ACCESS CODES
DELETING BADGES /
ACCESS CODES
 Press . Display will show the first badge or code that is learned into the system
 Use the
to find the badge or code you wish to delete
 Press
Deleting a Code:
 Display shows
RE-ENTER THE
CODE
 Enter teh code you wish to delete and press
 Display shows
DELETING CODE
NAME OF CODE
 Press
 The code is now deleted from the system
Deleting a Badge:
 Display shows
 Press
DELETING BADGE
NAME OF BADGE
 The badge is now deleted from the system
Exiting From Programming
1. Keypad (XMA/WMB)
From any menu in programming you have exit back to the main screen
 Hold the for 5 seconds to retunr to the main display
11
NOTES
12
Download PDF
Similar pages