METHVEN AIO AURAJET OVERHEAD SHOWER

page 1 of 3
METHVEN
AIO AURAJET OVERHEAD SHOWER
220
87
410
1/2" BSP
Female
24
AOOSCPAU
2299911
SPECIFICATIONS
Recommended Use
Domestic, hotel and commercial
Colour
Chrome, and
Chrome with white face
Pressure Rating
Suitable for high pressure applications and has
been WELS certified to the following:
Minimum operating pressure 100kPa
Maximum operating pressure 500kPa
Temperature Rating
Maximum continuous working temperature 70°C
(recommended 38°C - 42°C)
Minimum 5°C
Suitable Hot Water
Units
AOOSCPWHAU
2299912
Storage Tank: Yes
Continuous Flow: Yes
Gravity Feed: Not recommended
Spray Patterns
Aurajet Spray
CLEANING RECOMMENDATIONS
We recommend the use of soapy water or approved cleaners. This
product should not be cleaned with abrasive materials. Damage caused
by improper treatment is not covered by the product warranty – refer to
warranty conditions on the last page.
TM
AS/NZS 3662
WMKT21090
Disclaimer: Products in this specification manual must by regulation be installed by
licensed and registered trade people. The manufacturer/distributor reserves the right to
vary specifications or delete models from their range without prior notification. Dimensions
are nominal measurements only. Dimensions and set-outs listed are correct at time of
publication however the manufacturer/distributor takes no responsibility for printing errors.
Tech Page Version 1
To see the complete AIO range go to
www.reece.com.au/bathrooms
IMPORTANT: Before you begin, turn off the water supply.
ons before installation.
Step 1
censed plumber in compliance with all
leaks.
IMPORTANT: Please read all
• Wall lining hole should be cut or finished as
per the dimension shown in the diagram on
of the
and turn off water
the instructions
right.
eliver water at a safe temperature as per
page 2 of 3
m
13±2m
supply before installation.
• Cut off the threaded nipple 13±2mm from
INSTALLATION INSTRUCTIONSthe wall lining and apply thread seal tape
26mm max
ensure a good seal.
IMPORTANT: Before you begin,toturn
off the water supply.
rproof seal is achieved.
m
Step 1
13±2m
you begin, turn off the water supply.
ower when used•with
gravity fed heated
Recommended
installation height is 2100mm from the ground.
a/1.5bar atStep
the outlet.
Additionally showers
1
m
• Wall
lining hole should be cut or finished as per3±
2mdimension
following to function
correctly:
1 the
shown in the diagram on the right.
• Wall lining hole should be cut or finished as
• Cut off the threaded nipple 13±2mm from the wall lining and
per theas
dimension
shown in the diagram
on
thread seal tape to ensure a goodStep
seal.2
e cut or finishedapply
the
right.
• Ensure o-ring is located on the inlet
in the diagram on
connector.
the threaded nipple 13±2mm from
• Cut off
½" BSP Nipple
Screw the inlet connector onto the nipple
(Not Supplied)
thefrom
wall
lining and apply thread seal• tape
le 13±2mm
ensuring that the o-ring is sufficiently
thread seal
tape a good seal.
to ensure
compressed to create a watertight seal.
26mm max
26mm max
O-ring
Step 2
Step 3
Connector
• Ensure Inlet
o-ring
is located on the inlet connector.
• Push the overhead shower onto the inlet connector.
Step•2Screw the inlet connector onto the nipple ensuring that the
is sufficiently
compressed
to create a watertight seal.
n the• inlet
Ensureo-ring
o-ring
is located
on the inlet
Step 3
connector.
• Ensure that the overhead shower is oriented horizontally
• Secure in place by tightening the grub screw firmly using
the hex key provided
• Push the overhead shower onto the inlet
connector.
onto• theScrew
nipplethe inlet connector onto the nipple
• Ensure that the overhead shower is oriented
s sufficiently
ensuring that the o-ring is sufficiently horizontally.
watertight seal.
compressed to create a watertight seal.
• Secure in place by tightening
the grub screw firmly using the
hex key provided.
Care and Cleaning:
Care and Cleaning
Run hot water through shower for 2 minutes before first use.
Never use abrasives or abrasive cleaning agents to clean this product. Clean regularly with
contamination free warm soapy water and a damp soft cloth.
Run hot water through shower for 2 minutes Clean
beforefilter
firstwasher
use. located in the shower head waterway periodically. To access filter washer,
pushto
down
on this
release
button,Clean
hold the
wall arm
and pull shower head away from it.
Never use abrasives or abrasive cleaning agents
clean
product.
regularly
with
contamination free warm soapy water and a Remove
damp soft
filtercloth.
washer from the shower head waterway
bywaterway
gently levering
out with aTo
small
screwfilter
driver.
periodically.
access
r onto the
inlet3Clean filter washer located in the shower head
Step
washer, push down on release button, hold the wall arm and pull shower head
away from it.
1
• is oriented
the overhead shower onto the inlet
shower Push
Remove filter washer from the shower head waterway by
connector.
gently levering out with a small screw driver.
ning •
ng the
2
Ensure that the overhead shower is oriented
horizontally.
• Secure in place by tightening
the grub screw firmly using the
hex key provided.
If shower performance is compromised by the build-up of lime-scale, soak in limescale
remover for up to 10 minutes. Refer to instructions above for how to remove shower head
Plumbers, please ensure a copy of the installation
from wall arm. Do not use products containing chlorine bleach or hydrochloric acid as
these
can damage the shower. Always rinse the shower thoroughly after cleaning to
instructions is left with the end user for future
reference
remove cleaning products that can damage the shower.
Never insert objects into the spray slot or attempt to remove limescale with sharp objects
AU
In
Tec
Ope
Min:
Max:
Opti
Ope
Hot:
Cold
Inle
All ½
* Reg
Plea
www
page 3 of 3
IT Y
TE
AL
E
LIFE
TIME
QU
METHVEN
AIO AURAJET
OVERHEAD
SATINJET
ESCAPE
MKII SHOWER
HI RISE SHOWER
G UARA
N
REECE PRODUCT QUALITY GUARANTEE
You have purchased a quality product from Reece Pty Ltd
ABN 84 004 097 090 (“Reece”). This product is covered by a
Lifetime replacement product warranty, including spare parts,
and a 12 month warranty covering labour.
LIFETIME YEAR WARRANTY – DOMESTIC USE
This warranty covers faults in the product construction, material
and assembly. Products which are, found upon inspection
by an authorised Reece representative, to be defective
in construction, material or assembly, will be repaired or
exchanged with an equivalent product free of charge. Replaced
items become Reece’s property.
All replacement products will be available for collection without
charge to the customer at the nearest Reece branch to the
customer’s location, or elsewhere as agreed between the
customer and Reece.
Labour and Spare Parts
The labour for the replacement of products and spare parts
to which this warranty applies will be supplied by Reece or
relevant supplier using licensed plumbers engaged by Reece or
relevant supplier within 1 year from the date of purchase.
Spare parts found upon inspection by an authorised Reece
representative to be defective in construction, material
or assembly, will be replaced free of charge for the life of
the product.
Warranty Conditions
This warranty will apply only under all of the
following conditions:
• The item has been installed by a licensed plumber
• The item has been installed for and subjected to domestic
residential use only
• Failure is due to a fault in the manufacture of the product
• Proof of purchase (including the date of purchase)
is provided
• The installation of the product is in accordance with the
instructions provided
This warranty does not cover products purchased as an
ex-display without being fully checked and tested for sale by
the manufacturer.
• Inadequate or complete lack of maintenance
• Chemical, electrochemical or electrical influences
• Harsh detergents or abrasive cleaners used on
product finishes
1 YEAR WARRANTY – COMMERCIAL USE
‘Commercial’ use is all use other than for normal domestic
residential purposes, including use in non-business places as in
public buildings, schools, sports centres and in establishments
that contain private bathrooms with high frequency of use by
many individuals, such as hotels, motels, retirement villages
and hospitals.
The Commercial warranty covers this product against
manufacturing faults in the construction, material and assembly
of both the finished products and any spare parts for a period
of 1 year from the date of purchase. Products and spare
parts which are found upon inspection by an authorised
Reece representative to be defective in construction, material
or assembly will be repaired or exchanged free of charge.
Replaced items become Reece’s property. The labour for the
replacement of products and spare parts to which this warranty
applies will be supplied by Reece or relevant supplier using
licensed plumbers engaged by Reece or relevant supplier.
The Warranty Conditions and exclusions which apply to the
domestic use warranty also apply to this commercial warranty.
EXCLUSIONS
To the fullest extent permitted by law, Reece excludes all liability
for damage or injury to any person, damage to any property,
and any indirect consequential or other loss or damage.
CLAIM PROCEDURE
For all warranty queries customers are to contact the branch
where the product was purchased. These details can be found
on your purchase invoice.
Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
This warranty does not include faults caused by:
• Unsuitable or improper use
• Installation or part installation by the purchaser or any person
other than a LICENSED PLUMBER
• Normal wear and tear
Don’t risk it, use a licensed plumber.™
SHOWER.METH.T2.LIFE
• Incorrect installation or installation not in accordance with
the instructions provided
Download PDF
Similar pages