Sensixx`x TDi90 i-Temp / AntiShine / Hygienic

Register your new Bosch now:
http://www.bosch-home.co.uk
Sensixx’x TDi90
i-Temp / AntiShine / Hygienic
enOperating instructions
Thank you for buying the “Sensixx’x
Di90” compact steam iron from Bosch.
Carefully read through the operating
instructions for the appliance and
safeguard them for future reference.
You can download this manual from the
local home pages of Bosch.
General safety instructions
❐❐ The iron must not be left
unattended
while it is connected
to the
General
safety instructions
2
Description4
supply mains.
Using your appliance
5
❐❐ Remove the plug from1.the
socket
before
the appliance with
Filling
the water
tank filling
5
2.
Heating
5
water or before pouring out the remaining water after use.
3. Setting the temperature6
❐❐ The appliance must be “i-Temp”
used and
placed on6 a stable surface.
programme
“AntiShine”
programme
6
❐❐ When placed on its stand, make sure that *the surface
on which the
“Hygienic” programme *6
stand is placed is stable.
4. “SensorSteam” function7
Steamifsettings7
❐❐ The iron should not be5.used
it has been dropped, if there are visible
6. Shot of steam function 7
signs of damage or if it7.is
leaking
water.
Vertical steam
8 It must be checked by an
8.
Spray8
authorized Technical Service Centre before it can be used again.
9. After ironing 8
Cleaning
& Maintenance
9
❐❐ With the aim of avoiding
dangerous
situations,
any work or repair
Descaling
systems
9
that the appliance may Aneed,
e.g. replacing a faulty mains cable,
“self-clean” 9
must only be carried outB “anti-calc”
by qualified
9 personnel from an Authorised
C
“Calc’nClean”
function9
Technical Service Centre.
Accessories10
11 aged from 8 years and
❐❐ This appliance can beTrouble
used shooting
by children
Guarantee
conditions
above and persons with
reduced
physical, 11
sensory or mental
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
❐❐ Keep the iron and its cord out of reach of children less than 8 years
of age when it is energized or cooling down.
❐❐ This appliance is designed only for household use up to 2000m
above sea level.
❐❐
2
C
AUTION. Hot surface.
Surface is liable to get hot during use.
B O S CH
Important notices
• This appliance has been designed
exclusively for normal household use in a
home environment..
• This appliance must be used only for
the purposes for which it was designed,
i.e. as an iron. Any other use will be
considered improper and consequently
dangerous. The manufacturer will not be
held responsible for any damage arising
from misuse or improper use.
• This appliance is to be connected and
used in accordance with the information
stated on its characteristics plate.
• This appliance must be connected to
an earthed socket. If it is absolutely
necessary to use an extension cable,
make sure that it is suitable for 16A and
has a socket with an earth connection.
• In order to avoid that, under unfavorable
mains conditions, phenomena
like transient voltage drops or
lighting fluctuations can happen,
it is recommended that the iron is
connected to a power supply system
with a maximum impedance of 0.21Ω. If
necessary, the user can ask the public
power supply company for the system
impedance at the interface point.
• In special environmental conditions slight
instability may occur.
• Never direct the steam jet at garments
that are being worn.
• The appliance must never be placed
directly under the tap to fill the water
tank.
• Unplug the appliance from the mains
supply after each use, or if a fault is
suspected.
• Never immerse the iron in water or any
other fluid.
• Do not leave the appliance exposed to
weather conditions (rain, sun, frost, etc.).
Advice on disposal
Our goods come in optimised packaging.
This basically consists in using noncontaminating materials which should be
handed over to the local waste disposal
service as secondary raw materials. Your
local town council can give you information
about how to dispose of obsolete
appliances.
This appliance is labelled in
accordance with European
Directive 2012/19/EU
concerning used electrical and
electronic appliances (waste
electrical and electronic equipment –
WEEE).
The guideline determines the framework
for the return and recycling of used
appliances as applicable throughout the
EU.
• Never aim the steam at people or
animals.
BOSCH
3
Description
1.Motor activation trigger *
2.“SensorSteam” indicator lamp
3.“SET” button
4.Steam setting indicator lamps
5.Spray button
6.Shot of steam button
7.Water inlet lid
8.Spray nozzle
9.Level mark for maximum filling
4
B O S CH
10.Soleplate
11.“clean” button
12.Temperature index
13.Temperature control with “TempOK”
indicator
14.“MotorSteam” indicator lamps
15.Heel
16.Power cable
* Model dependent
Using your appliance
1. Filling the water tank
This appliance has been designed to use normal tap water.
Important: Do not use additives! The addition of other
liquids, such as perfume, vinegar, starch, condensation
water from tumble dryers or from air conditioning systems
or chemicals will damage the appliance. Any damage
caused by the use of the aforementioned products will
make the guarantee void!
 1  Unplug the iron from the mains.
 2  Open the water inlet lid (7).
 3  Fill the water tank. Never fill beyond the level mark
for maximum filling (9)!
 4  Close the water inlet lid.
Tip: To prolong the optimum steam function, you may mix
tap water with distilled or demineralised water 1:1. If the
tap water in your area is very hard, mix tap water with
distilled or demineralised water 1:2.
ºC
45º
2. Heating
Remove any labels or protective covering from the
soleplate (10).
 1  Plug in the iron.
 2 “SensorSteam” function will be activated and the
indicator lamp (2) will flash.
 3  The “eco” steam mode is automatically selected.
 4  The “TempOK” indicator lamp (13) will flash, indicating
that the iron is heating up. When the iron is ready to
use, the indicator lamp will remain lit continuously.
BOSCH
5
3. Setting the temperature
Set the temperature control (13) to the corresponding
position by lining it up with the temperature index (12) on
the iron.
Temperature
●
●●
●●●
max
Suitable for
synthetics
silk – wool
cotton
linen
Tip: Start by ironing the fabrics that require the lowest
ironing temperature. Check the recommended ironing
temperature on the label on the garment.
“i-Temp” programme
This programme sets an appropriate combination of
temperature and steam, which is suitable for all fabrics
that can be ironed (symbols
).
The “i-Temp” programme does not apply to fabrics that
cannot be ironed (symbol
).
Please check the garment care label for details or try
ironing on a part of the fabric not visible normally.
AntiShine
“AntiShine” programme *
Suitable for dark and delicate fabrics. Reduces the risk of
shiny marks when ironing.
Tip: Try to iron the fabrics while they are still damp after
washing. Steam will be generated from the fabrics rather
than the iron.
Hygienic
“Hygienic” programme *
Suitable for all kinds of fabrics and extremely efficient in
both thick and delicate garments.
The unique combination of temperature and interval
steam provides a sanitizing effect requiring no chemical
additives.
Tip: To ensure the maximum efficiency of the “Hygienic”
programme, it is recommended to set the steam mode to
“max” (see section 5).
6
B O S CH
* Model dependent
4. “SensorSteam” function
After the initial heating, “SensorSteam” function switches
off the iron when it is left unattended, thus increasing
security and saving energy.
 1  While the handle is gripped, the iron heats up. The
“SensorSteam” indicator lamp (2) will remain lit
continuously.
 2  When the handle is released, the “SensorSteam”
function is activated. The “SensorSteam” indicator
lamp (2) will flash.
5. Steam settings
This iron generates steam by means of a built-in motor.
While the motor is working, the "MotorSteam" indicator
lamps (14) of the water tank come on.
The iron is equipped with a sensor and an electronic
system to adapt the amount of steam to the mode of use,
optimising both the ironing and the service life of the
appliance.
The steam mode can be selected by pressing the “SET”
button (3) successively. The iron runs through the
following cycle:
Steam mode
Indicator lamp (4)
Medium
(continuous steam)
“eco”
(green)
Maximum
(continuous steam)
“max”
(red)
Dry ironing
(ironing without steam)
off
Steam production can be controlled manually for steam
ironing only when necessary. Select dry ironing mode and
press the motor activation trigger (1*).
shot
6. Shot of steam function
Shot of steam can be used to remove stubborn wrinkles
or to press in a sharp crease or pleat.
 1  Set the temperature control (13) to at least “●●”.
 2  Press the shot of steam button (6) repeatedly with
intervals of at least 5 seconds.
* Model dependent
BOSCH
7
7. Vertical steam
Vertical steam can be used to remove creases from
hanging clothes, curtains etc.
10 cm / 4 in
 1  Set the temperature control (13) to “max”.
 2  Hang article of clothing on a clothes hanger.
 3  Operate the iron in a vertical position at a distance of
10 cm / 4 in, and press the shot of steam button (6)
repeatedly with pauses of at least 5 seconds.
8. Spray
Spray can be used to remove stubborn wrinkles.
 1  When ironing, press the spray button (5) and
water will spray out of the spray nozzle (8) onto the
garment.
Tip: Do not use the spray function with silk.
9. After ironing
 1  Unplug the iron from the mains socket.
 2  Empty the water tank.
 3  Set the iron aside in a vertical position on its heel (15)
to cool down.
 4  Coil the power cable (16) loosely around the heel of
the iron. Store the iron in an upright position.
Tip: For immediate storage of the iron, you may use the
“StoreProtect ” accessory (see “Accessories” section).
8
B O S CH
Cleaning & Maintenance
EEAttention! Risk of burns!
Always unplug the appliance from the mains
supply before carrying out any cleaning or
maintenance operation on it.
 1  If the iron is only slightly soiled, pull out the plug and
allow the soleplate (10) to cool down. Wipe the housing
and the soleplate with a damp cotton cloth only.
 2  To keep the soleplate smooth, you should avoid hard
contact with metal objects. Never use a scouring pad
or chemicals to clean the soleplate.
antiCalc
Descaling systems
A“self-clean”
The “self-clean” filter prevents motor from blocking.
B“anti-calc”
The “anti-calc” cartridge has been designed to reduce the
build-up of scale produced during steam ironing.
S
C“Calc'n Clean” function
The “Calc'n Clean” function helps to remove scale
particles out of the steam chamber.
If the water in your area is very hard, you may use this
function approximately every two weeks.
 1  Unplug the iron from the mains socket.
Tip: For deep descaling, it is recommended to use the
descaling liquid (see “Accessories” section). This
procedure should be carried out every 3 months.
25ml
Pour a measure (25 ml) of the descaling fluid into the
water tank.
45º
 2  Fill the water tank up to the level mark for maximum
filling.
BOSCH
9
 3  Plug in the iron and set the temperature to “max”.
 4  When the lamp “TempOK” (13) remains lit
continuously, unplug the iron (very important!).
 5  Hold the iron over a sink.
 6  Press the “clean” button (11) and shake the iron
back and forth keeping it in a horizontal position until
approximately one third of the water capacity of the
tank is evaporated. Boiling water and steam will
come out, carrying scale or deposits that might be
there.
 7  Release the “clean” button, and gently shake the iron
for some seconds.
 8  Repeat steps 6 and 7.
 9  Check carefully that the water tank is empty (very
important!).
 10  Plug the iron in and heat it up again until the
remaining water has evaporated.
 11  Unplug the iron and let the soleplate cool down. Wipe
the soleplate with a damp cotton cloth only.
Accessories
The accessories may be purchased from the customer
service or specialist shops.
Descaling
liquid
For deep descaling of
the steam iron.
Contents:
4 bottles x 25 ml
Name: TDZ1101
Accessory code:
00311715
10
B O S CH
“StoreProtect”
Enables an immediate and
safe storage of the iron, even
with a hot soleplate.
Name: TDZ1750
Accessory code:
00575960
“TextileProtect”
Used for steam-ironing
delicate garments at maximum
temperature and maximum
steam without damaging them.
Name: TDZ1550
Accessory code:
00575494
Trouble shooting
Problem
Probable cause
Solution
The iron does not
heat up.
The “SensorSteam” function
has been activated. The iron
is set to stand-by.
Grip the handle of the iron to
re-start it.
Water drips out of
the soleplate when
using the “shot of
steam” function.
You have pressed the shot
of steam button (6)
repeatedly without waiting
for 5 seconds between each
press.
Wait 5 seconds between each
press of the shot of steam
button.
Steam does not
come out in
horizontal position.
Dry ironing steam mode has
been selected.
Set the steam control to “eco”
or “max” position.
Excessive dripping
or steaming.
No proper closing of “clean”
button (11).
Point the iron away from the
ironing area. Actuate a few
times the “clean” button.
The motor does not
work.
The iron is not in a
horizontal position.
Use the iron in a horizontal
position.
Smoke comes out
when connecting the
iron for the first time.
This may be caused by the
lubrication of some of the
internal parts.
This is normal and will stop
after a few minutes.
Deposits come out
through the holes in
the soleplate (10).
Traces of lime scale are
coming out of the steam
chamber.
Carry out a cleaning cycle (see
“Calc'n Clean function”
section).
The appliance
makes a pumping
sound.
Water is being pumped into
the steam chamber.
This is normal.
If none of the above solves the problem, get in touch with
an Authorised Technical Service.
Guarantee conditions
The terms of the guarantee for this appliance are in
accordance with that stated by our representative for the
country in which it is sold.
The details of these conditions can be obtained from
the retailer from whom the appliance was purchased.
The purchase receipt must be presented when making
any claims against the terms of this guarantee.
BOSCH
11
Customer Service
Great Britain
Bosch Customer Service
Grand Union House
Old Wolverton Road Milton Keynes
MK12 5PT
002 Di90 GB i-Temp / AntiShine / Hygienic 09/17
9001183792
UK +44 (0)344 892 8979
IRL +353 (0)1450 2655
www.bosch-home.co.uk
Download PDF
Similar pages