HEATING TECHNIQUE
Centrometal d.o.o. - Glavna 12, 40306 Macinec, Croatia, tel: +385 40 372 600, fax: +385 40 372 611
TECHNICAL INSTRUCTIONS
for installation, use and maintenance
of pellet stove
CentroPelet Z6
TUZ6ENG-9-2016-HR
GB
Dear Customer,
We thank you for having chosen one of our products, the fruit of technological experience and of continual research for
a superior quality product in terms of safety, dependability, and service.
In this manual you will find all the information and useful suggestions to use your product with the maximum safety
and efficiency.
We highly recommend to turn to our Authorized Service Centre for the installation and the first
ignition of the device as it not only carries out the installation perfectly but also verifies the
regular operation of it.
• Incorrect installation, incorrectly performed maintenance, improper use of the product release the manufacturer from
every eventual damage derived from the use of the stove.
• The unit cannot be used as an incinerator. Do not use fuels other than pellets.
• This manual has been realized by the manufacturer and constitutes an integral part of the product and must remain
with it during its entire lifetime. If the product is sold or transferred, be sure that the booklet is present since the
information contained in it are addressed to the buyer, and to all those persons of various titles who complete the
installation, use and maintenance.
• Carefully read the instructions and the technical information contained in this manual, before proceeding with the
installation, use, and any operation on the product.
• The observance of the indications contained in the present manual guarantees the safety of people and the product,
the economy of use and a longer functioning lifetime.
• Although the carefully studied design and the risk analysis done by our company has permitted the realization of a
safe product, in any case, before effecting any operation on the stove, it is recommended to keep said manual available and pay scrupulous attention to the instructions written therein.
• Be very careful when moving the ceramic details where present.
• Check the precise flatness of the pavement where the product will be installed
• The wall where the product will be placed must not be constructed in wood, or in any case, made of an inflammable
material, and in addition it is necessary to maintain a safety distance.
• While the stove is in operation, several parts of the stove (door, handle, sides) can reach high temperatures. Therefore
pay attention and use the proper precautions, above all in the presence of children, elderly or disabled persons, and
animals.
• Assembly must be performed by authorized persons (Authorized Assistance Center).
• Diagrams and drawings are furnished for the purpose of illustration; the manufacturer, with the intent of pursuing a
policy of constant development and renewal of the product can, without any notice, make any modifications that are
believed opportune.
• When the stove is working at its maximum speed, it is strongly suggested to wear gloves while handling with the
door for pellets loading and the door handle.
• It is prohibited to install in bedrooms or in explosive environments.
• Only use replacement parts recommended by the supplier.
Never cover the body of the stove in any way or obstruct the openings placed on the upper side
when the device is operating. All our stoves are trial lighted on the construction line.
In the event of a fire, disconnect the power supply, use an extinguisher and call the fire fighters if necessary.
After that contact the Authorized Assistance Center.
This instruction booklet is an integral part of the product: make sure that it always accompanies the appliance, even in
case of transfer to another owner or in the case of transfer to another place. In the event of damage or loss, request a
copy from the area technician.
These symbols indicate specific messages in this booklet:
ATTENTION:
This warning sign indicates that the message to which it refers should be carefully read and understood,
because failure to comply with what these notices say can cause serious damage to the stove and
put the user’s safety at risk.
INFORMATION:
This symbol is used to highlight information which is important for proper stove operation. Failure to
comply with these provision will compromise use of the stove and its operation will not be satisfactory.
2
GB
Norms and declarations of conformity
Our company declares that the stove conforms to the following norms for the EC European Directive labelling:
• 2014/30 UE (regulation EMCD) and following
amendments;
• 2014/35 UE (Low Voltage Directive) and following
amendments;
• 2011/65 EU (RoHS 2 directive);
• The New Rules of Construction Products (CPR-Construction Products Regulation) No. 305/2011 regarding
the construction world;
• For installations in Italy, please refer to UNI 10683/98 or
following changes. While installing the unit respect
the local, national and Europen rules;
• EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3;
EN 60335-1; EN 60335-2-102; EN 62233, EN 50581.
Safety information
Please carefully read this use and maintenance manual
before installing and operating the stove!
If clarification is needed, please contact the dealer or the
Authorized Assistance Center.
• The pellet stove must only be operated in living environments. This stove, being controlled by an electronic
board, permits a completely automatic and controlled
combustion; the exchange, in fact, regulates the lighting
phase, 5 power levels and the shut down stage, guaranteeing the safe operation of the stove.
• The basket used for combustion allows most of the ash
produced by the combustion of the pellets to fall into
the collection compartment. Nevertheless, check the
basket daily, given that not all pellets have high quality
standards (use only quality pellets recommended by the
manufacturer).
Responsibility
With the delivery of the present manual, we decline all
responsibility, both civil and penal, for accidents deriving
from the partial or total lack of observance of the instructions contained herein.
We decline every responsibility derived from improper
use of the stove, from incorrect use by the user, from unauthorized modifications and/or repairs, from the use of
replacement parts that are not original for this model.
The manufacturer declines every civil or penal, direct or
indirect responsibility due to:
• Lack of maintenance;
• Failure to observe the instructions contained in the
manual;
• Use in non-conformity with the safety directives;
3
• Installation in non-conformity with the norms in force in
the country;
• Installation by unqualified or untrained personnel;
• Modifications and repairs not authorized by the manufacturer;
• Use of non-original replacement parts;
• Exceptional events.
• Use only wood pellets;
• Keep / store the pellets in a cool dry
place;
• Never pour pellets directly on the hearth;
• The stove must be fueled only with quality
pellets with a diameter of 6 mm and a maximum
length of 30 mm of the type recommended by
the manufacturer.
• Before making the electrical connection of the
stove the discharge tubes must be connected
with the flue;
• The protective grill placed inside the pellet
container must never be removed;
• The environment where the stove is installed
must have a sufficient exchange of air;
• It is forbidden to operate the stove with the door
open or the glass broken;
• Do not use the stove as an incinerator; the stove
should be used only for the intended purpose;
• Any other use is considered improper and
therefore dangerous. Do not put in the hopper
other than wood pellets;
• When the stove is operating, the surfaces, glass,
handle and tubes become very hot: during
operation do not touch these parts without
adequate protection;
• Keep the fuel and other inflammable materials
off the stove.
Fuel is loaded from the upper part of the stove by opening
a door.
Pour the pellets in the hopper; vacuum contains about 11
kg of pellets. This is easier if performed in two steps:
• Pour half of the contents of the bag into the hopper and
wait for the fuel to settle on the bottom.
• Then pour in the second half;
• Keep the cover closed , after loading the pellets , the lid
of the fuel tank;
• Before closing the door load-pellet make sure that there
are no residues of pellets around the seal. If carefully
cleaned to avoid compromising the seals.
GB
Charge pellet
Never remove the protection grille in the
hopper. When filling, do not let the sack
of pellets touch any hot surfaces.
The stove is a product by heating, presents the external
surfaces particularly hot.
For this reason, we recommend extreme caution when
operating in particular:
• Do not touch the stove body and the various components,
do not approach the door , it could cause burns;
• Do not touch the exhaust fumes;
• Do not perform any type of cleaning;
• Do not dump the ashes;
• Do not open the ash tray;
• Be careful that children do not come near;
Instructions for safe and efficient use
• The device can be used by children that are not less than
8 years old and people with reduced physical, sensory or
mental capabilities, or lack of experience or knowledge,
provided being under supervision of someone responsible
or after having received instructions relating to the safe
use of the device and to the understanding of the dangers
inherent to it. Children should not play with the device.
Cleaning and maintenance to be performed by the user
should not be made by children without supervision;
• The stove must be connected to an electrical system
equipped with an earthing conductor in accordance with
regulations 73/23 and 93/98 EEC;
• The system must be of adequate electrical power
declared the stove;
• Do not wash the inside of the stove with water.
The water could damage the electrical insulation, causing
electric shock;
• Do not use the stove as a ladder or scaffold;
• Do not put clothes to dry on the stove.
Any clothes hangers and suchlike must be kept a suitable
distance from the stove. - Risk of fire
• Do not expose your body to hot air for a long time.
Do not overheat the room you are in and where the stove
is installed.
This can damage the physical conditions and cause
health problems;
• Carefully explain that the stove is made from material
subjected to high temperatures for the elderly, the
disabled, and in particular for all children, keeping them
away from the stove during operation
• Do not expose to direct the flow of hot air plants or
animals;
• The pellet stove is not a cooking element;
• Do not touch the stove with wet hands: the stove has
electrical components that could produce sparks if
handled incorrectly.
• External surfaces during operation can become very
hot. Do not touch them except with the appropriate
protection.
• Never open the glass door of the pellet stove while the
stove is in operation.
4
GB
Operating area
For proper functioning and a good temperature distribution,
the stove shoul be positioned in a location where it is able
to take in the air necessary for combustion of the pellet
(about 40 m3/h must be available), as laid down in the
standard governing the installation and in accordance with
local national standards.
The volume of the room must not be less than 30 m3.
The air must come in through permanent openings made
in walls (in proximity to the stove) which give onto the
outside, with a minimum cross-section area of 100 cm2.
These openings must be made in such a way that it is not
possible for then to be obstructed in any way. Alternatively,
the air can be taken from rooms adjacent to the one which
needs ventilating, as long as they are provided with an air
intake from the outside, and are not used as bedrooms or
bathrooms, and provided there is no fire risk such as there
is for example in garages, woodsheds, and storerooms,
with particular reference to what is laid down in current
standards.
It is not permissible to install the stove in
bedrooms, bathrooms, or in a room where
another heating appliance is installed
(fireplace, stove etc.) which does not have its own
independent air intake.
Locating the stove in a room with an explosive
atmosphere is prohibited.
The floor of the room where the stove is to be
installed must be strong enough to take its weight. If
walls are flammable, maintain a minimum distance
of 10 cm at the rear (A), of 30 cm at the side (B) and
100 cm at the front.
If the room contains objects which are believed to
be particularly delicate, such as drapes, sofas and
other furniture, their distance from the stove should
be considerably increased.
10 cm (A)
30 cm
(B)
Min.
100
cm2
Connection to the external air intake
It is essential that at least as much air must be able to flow
into the room where the stove is installed as is required for
proper combustion in the appliance and for the ventilation
of the room.
This can be effected by means of permanent openings in
the walls of the room to be ventilated, which give onto the
outside, or by single or collective ventilation ducts.
For this purpose, on the external wall near the stove, a
hole must be made with a minimum free cross-section of
100 cm2. (equivalent to a round hole of 12 cm diameter or
a square hole 10x10 cm) protected by a grille on the inside
and the outside.
5
The air intake must also:
• communicate directly with the room where the stove is
installed
• be protected by a grille, metal mesh or suitable guard, as
long as this does not reduce the area below the minimum
• be positioned in such a way as to be impossible to
obstruct.
In the presence of wood floors, install a
floor protection surface in compliance
with the rules in force in the country
GB
Connection to the flue pipe
The flue pipe must have internal dimensions not larger
than 20x20 cm, or diameter 20 cm. In the event of larger
dimensions, or of the flue pipe being in poor condition ( for
example cracks, poor insulation, etc.), it is advisable to fit
a stainless steel pipe of suitable diameter inside the flue
pipe throughout its length, right up to the top.
Check with suitable instruments that there is a draught
between 10 Pa and 12 Pa. This type of connection
ensures the evacuation of the fumes even in the event of
a temporary power cut.
At the bottom of the flue pipe, provide an inspection cap
to allow periodic checking and cleaning, which must be
done annually. Make a gas-tight connection to the flue
pipe, using pipes and connectors as recommended by us.
You must ensure that a windproof cowl should be fitted
which complies with the standards in force
Connection to an external flue with insulated or
double-wall pipe
The only type of pipe which is permissible is insulated
(double-walled) stainless steel, smooth on the inside,
fixed to the wall.
Flexible stainless steel pipe must not be used. At the
bottom of the flue pipe, provide an inspection cap to allow
periodic checking and cleaning, which must be done
annually. Make a gas-tight connection to the flue pipe,
using pipes and connectors as recommended by us. You
must ensure that a windproof cowl should be fitted which
complies with the standards in force.
Check with suitable instruments that there is a draught
between 10 Pa and 12 Pa.
Connection to the flue pipe
For proper functioning, the connecting pipe between the
stove and the chimney or flue duct must have a slope of
not less than 3% in the horizontal stretches, the length of
which must not exceed 2 metres and the vertical distance
between one tee connector and another (change of
direction) must not be less than 1,5 m. Check with suitable
instruments that there is a draught between 10 Pa and 12
Pa. At the botton of the flue pipe, provide an inspection
cap to allow periodic checking and cleaning, which must
be done annually.
Make a gas-tight connection to the flue pipe, using pipes
and connectors as recommended by us.
You must ensure that a windproof cowl should be fitted
which complies with the standards in force.
Fig. 2: connection to the
flue pipe.
Fig. 3: connection to an
external flue with insulated or
double-wall pipe.
6
GB
Fireplace flue gas
Distance to objects
Avoid contact with combustible materials (example:
wooden beams) and in any case provide for their insulation
with flame retardant material. In case of pipe penetrations
through roofs or walls is recommended to use special
kits crossing, certificates, are available commercially. In
the event of a chimney fire, turn off the stove, disconnect
from the network and never open the door. Then call the
authorities.
It is also recommended to keep the pellets and all
flammable materials at a suitable distance from the stove.
10 cm
30 cm
The chimney cap
The chimney cap must respect the following requirements:
• It must have the equivalent diameter and internal form
of the flue.
• It must have a useful outlet diameter of not less than
double that of the flue.
• The chimney cap on the roof or that remains in contact
with the outside (for example, in case of open lofts or
attics), must be covered with elements in brick or tile
and must, in any case, be well insulated.
• It must be constructed to prevent rain, snow, and
extraneous bodies from entering the flue and so that
the discharge of the products of combustion is not
inhibited by wind from any quarter or strength (windproof chimney cap).
• The chimney cap must be positioned in such a way as
to guarantee the adequate dispersion and dilution of the
products of combustion and in any case, must be out of
the reflux zone. This zone has different dimensions and
forms according to the angle of inclination of the roof so
it is necessary to adopt minimum heights.
• The chimney cap must be a wind-proof type and must
be above the ridge.
• Eventual structures or other obstacles that are higher
than the chimney cap must not be too close to the
chimney cap itself.
• The device should not be installed in the flue shared.
YES
NO
Fig. 5: characteristics of chimney
7
100 cm
REMARKS:
- the appliance must be installed by a qualified technician in
possession of the technical and professional requirements
according to the DM37/2008 that, under its responsibility,
to ensure compliance with the rules of good technique.
- you need to keep in mind all laws and national, regional,
provincial and municipal laws of the country in which you
installed the device
- check that the floor is not flammable: if necessary use a
suitable platform
- in the room where the generator must be installed to
heat must not pre-exist or be installed with an extractor
hood or ventilation ducts of the collective type.
Should these devices be located in adjacent rooms
communicating with the installation, and ‘prohibited the
simultaneous use of the heat generator, where there is a
risk that one of the two rooms being placed in depression
than the other
- it is not permissible to install in bedrooms or bathrooms.
5
1
GB
Control board
6
AL C
AL F
4
2
7
11
8
9
10
12
3
1. Temperature or power decrease
2. Temperature or power increase
3. Key On/Off
4. Receiver
5. Led alarm ALC
6. Led alarm ALF
7. Led chrono-thermostat
8. Led temperature ok
9. Led pellets loading
10. Led resistance
11. Display LED 7 segments
12. Led On/Off
Display keys and functions
1. Using the key on the menu Set temperature, you can
decrease the temperature from a maximum value of 40 °C
to a minimum value of 7 °C.
With the key on the menu Set power, you can decrease the
working power from a maximum value of 5 to a minimum
value of 1.
2. Using the key on the menu Set temperature, you can
increase the temperature from a min. value of 7°C to a
max. value of 40°C.
With the key on the menu Set power, you can increase the
working power from a min. value of 1 to a max. value of 5.
3. Keep the key pressed for 2 seconds to switch the stove
on or off.
4. Sensor receiving the settings of the remote control.
5. The led blinks in the event of a malfunction or alarm.
6. The led blinks in the event of a malfunction or alarm.
7. This means the automatic single or daily programming
of the switching on or off of the stove is on.
The automatic programming can be set only with the
remote control (optional).
10. This led is on only while the stove is lighting up in order
to indicate that the resistance is warming the air which will
fire the pellets.
11. On the display you can read the different working
functions of the stove, the room temperature and the set
working power. In the event of a malfunction, the display
shows the relative error codes (see paragraph on alarm
codes).
12. This led indicates the different phases of the stove:
- it is on if the stove is switched on and working
- it is off if the stove is switched off
- it blinks if the stove is switching off
Stove setting
How to change the wished room temperature
Join the following procedure to change the wished
temperature: press the key
(1) once to enter the menu
and set temperature. You will read the word “Set” and the
wished temperature on the display. Use the keys
(2)
and
(3) to increase or reduce the wished value.
The stove will leave the menu Set temperature automatically
as soon as you do not work on it for some seconds.
AL C
1
2
AL F
3
How to change the working power
Join the following procedure to change the working power:
(1) once to enter the menu and set the
press the key
working power. You will read the word “Pot” and the range
(2)
of 5 possible powers on the display. Use the keys
and
(3) to increase or reduce the wished value.
The stove will leave the menu Set working power
automatically as soon as you do not use it for some
seconds.
AL C
AL F
8. This is on when the stove reaches the set temperature.
In this case you will read the word “Eco” and the set
temperature on the display.
9. This led blinks every time the stove is loading pellets.
2
1
3
8
GB
Remote control (if any)
Keys and main functions
TURBO
This key activates or deactivates the function
TURBO. Keep the key pressed for at least two
seconds to activate or deactivate this function.
The remote control can be used
to check the stove. The remote
control offers some functions
which are not available from
the keyset, like the automatic
programming of the switching on
and off of the unit.
CLOCK FUNCTION
Please join the following procedure to set the clock
function on the remote control:
and the time blinking.
- press the symbol
- use the keys
and
to set hour and
minutes.
- press
again to confirm and SEND to transmit
the function to the pcb.
How to use the remote control:
1. Direct the remote control on
the control board of the stove
2. Check there are no obstacles
between the remote control and
the receiver on the stove
3. Every function you set on the
remote control must be confirmed
pressing the key SEND. After
selecting the wished function, an
acoustic signal will confirm your
choice.
ON1
Using this key you can set a single time schedule for
the automatic switching on of the stove (program 1).
LCD 2
On/Off
This function is used to switch the stove and the
remote control on or off. Keep the key pressed for
at least two seconds to switch the system on or
off. Then press the key SEND.
You can use the two keys to set the wished
temperature between a min. value of 7°C and a
max. value of 40°C.
Please join the following procedure to set the
functioning mode:
Automatic Functioning
power 1
(on1)
power 2
(on2)
power 3
(on3)
power 4
(on4)
power 5
(on5)
SEND
Use this key to transmit the selected information
to the pcb.
ECONO
This key activates or deactivates the function
ECONO. Keep the key pressed for at least two
seconds to activate or deactivate this function.
9
OFF1
Using this key you can set a single time schedule
for the automatic switching off of the stove
(program 1).
ON2
Using this key you can set a single time schedule
for the automatic switching on of the stove
(program 2).
OFF2
Using this key you can set a single time schedule
for the automatic switching off of the stove
(program 2).
AUTO
With this key you can decide to repeat the
programmed switching on and off (program 1 and
2) every day. The key AUTO activates this function.
Keep the key pressed for at least two seconds to
activate or deactivate this function.
CANCEL
Use the key CANCEL in the event you want to
cancel some programmed switching on or off of
the stove.
GB
Function TURBO
You can change the temperature
using the keys
(1) and
(2). The temperature range goes
from a min. value of 7°C to a
max. value of 40°C.
Once you have chosen the
wished temperature, confirm
your selection pressing the key
(3).
This function has been developed
in the event you need to heat your
room quickly, for example when you
have just switched the stove on.
When you choose this function, the
2
stove will work at its max. power for
a period of thirty minutes and the
temperature will be automatically
3
set at 30°C. After thirty minutes (or
earlier if you give different selections
1
from the remote control), the stove
will restart working as it did before
you activated the turbo function.
Keep the key TURBO (1) pressed for at least two seconds
to activate this function. You will read the word “TURBO”
(2) on the display of the remote control. Set temperature
and working power will disappear. Press SEND (3) to
transmit the selection to the pcb.
You will read the word “Turb” on the control board on the
upper part of the stove. This word will appear together
with the room temperature and working power set before
activating the function TURBO.
If you want to deactivate this function before thirty minutes
have passed, press the key TURBO (1) once again for at
least two seconds. The word TURBO on the display of
the remote control will disappear and you will see the set
temperature and power again. Press the key SEND (3) to
confirm your selection.
Set
temperature
Change the temperature
1
2
3
Change the power
(1)to select the
Use the key
power of the stove. The marks
(2) on the display of the remote
control indicate the five possible
powers. Press the key SEND
(3) to confirm your selection.
You will see the words on1on2-on3-on4-on5 and the room
temperature on the control
board of the stove according to
the selected power.
You can also select the
automatic
function.
Please
refer to the paragraph on the
Automatic Power Function to
understand how the stove works
in this mode.
2
1
3
Automatic power function
To enter this function, press
the key
(1), until you see
the symbol
on the display.
Press SEND (2) to transmit
your selection. You will read
the word “Auto” and the room
temperature on the control
board of the stove.
When you select this mode, the
1
pcb will set the working power
2
automatically according to the
difference in degrees between
the set temperature and the temperature identified by the
sensor on the back of the stove.
Press
, once more, select the wished power and press
SEND to go back to the usual functioning.
Function ECONO
The function ECONO has been
developed to save money and it is
used when you want to keep the
temperature constant in the room.
2
This function lets the stove decrease
its working power every 10 minutes
until it reaches the power 1.
3
Keep the key ECONO (1) pressed
for at least two seconds to activate
1
this function. You will read the word
“ECONO” (2) on the display of the
remote control. Set temperature
and working power will disappear.
Press SEND (3) to transmit the selection to the pcb.
You will read the word “Econ” on the control board on the
upper part of the stove. This word will appear together
with the room temperature and working power set before
activating the function ECONO.
If you want to return to the standard function, press the
key ECONO (1) once again for at least two seconds. The
word ECONO on the display of the remote control will
disappear and you will see the set temperature and power
again. Press the key SEND (3) to confirm your selection.
10
GB
Function chrono-thermostat
(available only through the remote control)
5
With the function chrono-thermostat, you can schedule
up to two automatic switching on and off of the stove per
day.
If you want to repeat the switching on and off every day,
then you need to use the function AUTO too (as explained
in the paragraph “Daily repeat AUTO”).
AL C
AL F
Automatic switching off OFF1
• The time of the automatic switching on
and off must be set when the remote
control is Off;
• In the event of an even very short lack of current,
you will miss the set time for the automatic
switching on or off. Once the power supply is
back, please program the stove again using the
remote control;
• The stove switching on at the scheduled time will
keep the same temperature and power you set
before you last switched it off;
• Please consider an interval of min. 20 minutes
between the switching off and subsequent
switching on of the stove. In this way the unit
will have time to arrange a complete cooling
phase; in the event this minimal interval is
not calculated, the stove will not switch on as
scheduled.
OFF1
Press the key
(1). You will
see the hours and minutes and
the symbol OFF1 blinking on the
remote control. Use the keys
(2) and
(3) to change
the wished time (intervals of
10 minutes). To scroll the time
faster, keep the keys
(2)
and
(3) pressed.
4
Confirm your selection pressing
2
the key
(1). once again.
You will now read the set
3
switching off time on the remote
1
control. Press SEND (4) to
transmit your selection to the pcb of the stove.
The LED chrono-thermostat will light up on the control
board indicating that the programming is on (5).
The LED chronothermostat switches off as soon as the
automatic switching on and off are completed.
The remote control does not show the previously set time
schedule anymore.
Program 1 (ON1 and OFF1)
Automatic switching on ON1
Program 2 (ON2 and OFF2)
As above but with the keys
ON2 and OFF2
ON 1
Please join the following
procedure to set the time for
the automatic switching on
according to the program 1:
Press the key
(1). You will
see the hours and minutes and
the symbol ON1 blinking on the
remote control. Use the keys
4
(2) and
(3) to change
2
the wished time (intervals of
10 minutes). To scroll the time
3
faster, keep the keys
(2)
and
(3) pressed.
1
Confirm your selection pressing
the key
(1) once again.
You will now read the set switching on time on the remote
control. Press SEND (4) to transmit your selection to the
pcb of the stove.
The LED chrono-thermostat will light up on the control
board indicating that the programming is on (5).
11
Cancel any eventual already
set timetables.
Please join the following
3
procedure to cancel any other
already set timetables. This
example refers to the automatic
1
switching off of the program
1 (Off1). The procedure is the
2
same for all plans.
Press the key corresponding to
the switching on or off time you want to cancel.
Referring to the example: press the key
(1).
You will see the hours and minutes and the symbol OFF1
blinking on the display of the remote control. Now press
the key “CANCEL” (2) to cancel the automatic switching
on or off timetables from the display.
Press the key SEND (3) to confirm your selection and
transmit it to the pcb of the stove.
GB
Daily repeat AUTO
2
Using the function AUTO, you
can repeat the single automatic
switching on and off you
selected every day.
You just need to press the key
AUTO (1) for at least two seconds
3
to activate the function. You will
read the words AUTO (2) on the
display of the remote control.
Press SEND (3) to confirm your
1
selection and transmit it to the
pcb of the stove.
The LED chrono-thermostat
will light up on the control board indicating that the
programming is on.
You can deactivate the automatic repeat whenever you
want just pressing the key AUTO again for at least two
seconds. The words AUTO will disappear from the display.
Press SEND (3) to confirm your selection and transmit it to
the pcb of the stove.
Always clean the brazier before starting an
automatic switching on in order to avoid
any possible missed starts up which would
damage your stove and the environment.
Replace the batteries of the remote control
If you need to replace the
batteries of the remote
control, remove the back
cover as shown in the
picture. Replace the old
batteries with the new ones
respecting the polarity +
and -.
The batteries needed are
AAA, 1,5 V.
Display information
“OFF”: the stove is off or it is in a shutting
down phase.
“FAN-ACC”: the stove is in the phase
of preheating the resistor, preceding
lighting.
“LOAD WOOD”: the stove is loading
pellets. On the control board the LED
resistance is on.
“FIRE ON”: The stove is in the flame
stabilization phase (flame present).
“ON 1”: the stove is in the operational
phase at minimum power.
“ECO”: the stove has reached the
temperature set by the user and is in the
energy saving phase. In this phase it is
not possible to modify the power setting.
If the temperature is set at 41°C the stove
will remain in continuous operation at
the programmed work power without
passing to the economy mode (ECO).
“STOP FIRE”: the stove is in a selfcleaning of the basket phase; the smoke
extractor runs at the maximum speed
and the pellet loader at minimum.
“ATTE”: you will read these letters when
you try to start up the stove while it is
completing a cooling cycle. Wait until
the cooling phase is completed before
proceeding with a new switching on.
12
770
770
Aspirazione Aria
Air intake
50
431 25
80
80
177
158
174
25
174 107
107
770
770
487
487
32 431
Flue gas tube
50
158
32
6
Uscita Fumi
177
GB
Technical Specification
Materiale
TOLLERANZE GENERALI DI LAVORAZIONETOLLERANZE GENERALI
DI LAVORAZIONE
DIMENSIONI LINEARI
DIMENSIONI LINEARI
GRADO DI
Peso
I
2000A OLTRE
FINO A DA
DA 400 DA 1000 DAFINO
6 DA 60 DA 120 PRECISIONE
DA
6 DA 60 DA 120 DA 400 DA 1000
GRADO DI
PRECISIONE
6
6
A
± 0,15
60
± 0,1
± 0,05
120
A
400
A 1000
A 2000
A 4000
6
± 1,2
±±20,15
± 0,15
± 0,25
± 0,4
± 0,6
±12
1
±±1,5
0,1
± 0,1
± 0,15
± 0,2
± 0,3
±3,2
0,5
± 0,2
12
3,2
A
± 0,5
± 0,3
± 0,8
DIMENSIONI ANGOLARI
LUNGH. LATO CORTO
FINO A 10
CAMPO TOLLERANZA
± 3°
DA 10 A 50 LUNGH.
DALATO
50 A CORTO
150
± 2°
CAMPO TOLLERANZA
± 1°
± 0,05
36030 San Vito di Leguzzano(VI) - ITALIA
Disegnato
MZ
400
±±3,5
0,2 Spessore
± 0,3
± 0,5
±±2.5
0,15
± 0,4
± 0,25
± 0,1 Trattamento
± 0,2
± 0,15
A 1000
H
G
± 0,8
F
± 0,6
E
± 0,3
DIMENSIONI ANGOLARI D
OLTRE
FINO150
A 10
± 30'
± 3°
Il presente disegno rimane di proprietà di AMG S.p.A.
Ci riserviamo di tutelare i nostri diritti a termini di legge
Via delle Arti e dei Mestieri 1/3
41547
A 120 gA
4000
A
60
Approvato
Via delle Arti e dei Mestieri 1/3
ColoreDA 10 A 50
± 2°
A 2000
± 1,2
±2
± 3,5
±1
± 1,5
± 2.5
± 0,5
C 50 A 150
DA
B ± 1°
OLTRE 150
36030 San Vito di Leguzzano(VI) - ITALIA
41547 g
Spessore
legge
Approvato
MZ
ASSIEME
6KW ESTETICA MIGNON
I
- measurements are approximate and may
vary based on to the aesthetics of the stove
- the positions of the tubes in the rear view
are indicative and tolerance of +/- 10 mm
- measures with a tolerance of about 10
mm
13
Scala
Data
B
A
Modifica Rev.
1:5 17/05/2016
Data
Dis.
Modifica
DESCRIZIONE
ASSIEME 6KW ESTETICA MIGNON
32
32
487
487
431
431
426
426
4705001
E
D
C
426
426
REMARKS:
Codice
H
G
F
Colore
± 30'
Ci riserviamo
di tutelare
i nostri
diritti a termini
di
1:5
17/05/2016
Data
Rev.
Dis.
Rev.
4705001
Peso
Trattamento
Scala
Datadisegno rimane
A di proprietà di AMG S.p.A.
Il presente
Disegnato
DESCRIZIONE
Codice
Materiale
DA 2000 OLTRE
A 4000 4000
Rev.
GB
PARAMETER
UNIT OF M.
CENTROPELET Z6
Heat input
kW
6,15
Nominal heat output
kW
5,53
Reduced heat output
kW
2,5
CO concentration at nominal reference (13% O2)
mg/m3
185,6
CO concentration at reduced reference (13% O2)
mg/m3
633,2
Nominal efficiency
%
90
Reduced efficiency
%
93,34
Pellet consumption (min-max)
Kg/h
1,28 - 0,54
Heated surface
mc
160
Flue gas flow rate (min-max)
g/s
3,81 - 2,11
Draft advised (min-max)
Pa
8-5
Flue gas temperature (min-max)
°C
175,21 - 97
Tank capacity
Kg
11
Recommended fuel
(ø x H) mm
pellet 6 x 30
Diameter smoke outlet tube
mm
80
Diameter air intake
mm
50
Nominal voltage
V
230
Nominal frequency
Hz
50
Power consumption max
W
62 - 300
Stove weight
Kg
45
N° Test Report
K18532016T1
It is recommended that the control of emissions after installation.
Pellet
The pellets are cylinders of compressed wood, produced from sawdust and wood processing (chips and
sawdust), generally produced by sawmills and carpenters. The binding capacity of the lignin contained
in wood, allows to obtain a compact product without adding additives and foreign chemicals to the
wood, is therefore obtained a natural fuel with high yield.
The use of expired pellets or any other unsuitable material can damage parts of
the stove and impair proper operation: this can lead to the termination of the
guarantee, and its producer responsibility.
For our stoves use pellets diameter 6 mm, length 30 mm and a maximum
of 8% moisture. Store the pellets away from heat sources and not in
humid environments or with explosive atmospheres.
14
GB
Stove start up
Remove any components which might
burn from the firebox and from the glass
(various instructions and adhesive labels).
Charge pellet
Fuel is loaded from the upper part of the thermostove
by opening a door. Pour the pellets in the hopper. When
empty contains about 11 kg of pellets.
This is easier if performed in two steps:
• Pour half of the contents of the bag into the hopper and
wait for the fuel to settle on the bottom.
• Then pour in the rest.
Never remove the protection grille in the
hopper. When filling, do not let the sack of
pellets touch any hot surfaces.
The brazier should be cleaned before each
starting.
First lighting of the stove
• Before switching on, make sure that the grate is clean and
empty of any pellet residues from previous combustions.
Otherwise make sure you empty and clean it
• Fill the container 3/4 full with the pellets recommended
by the manufacturer
• Connect the stove to an electrical outlet with the cable
that has been supplied
• Press the lighting switch located on the back part of the
stove
• The upper display will read “OFF”
• Press the button for 2 seconds. After a few moments
the smoke extractor and the lighting resistor will start
and the display will read “START”; The led resistance is
switched on
• After 1 minute the display will read “LOAD PELL ET ”, the
stove will load the pellets and continue lighting the resistor
• Once the appropriate temperature has been reached
the display will read “FLAME LIGHT”: this means that the
stove has begun the last phase in lighting, at the end of
which the stove will be completely operational; The led
resistence is switched off
• After some minutes the display will show the words
“WORK” alternating room temperature and current working
power. The stove is now completely on
• When the stove reaches the set temperature, the display
will show “MODULATION”.
15
Before lighting a small amount of smoke
may fill the combustion chamber.
We highly recommend to turn to our
Authorized Service Centre for the
installation and the first ignition of the
device as it not only carries out the installation
perfectly but also verifies the regular operation of it.
During the first lighting the environment should
be well ventilated since during the first hours of
operation unpleasant odours could develop due to
the physical stabilizing of the paint and from the
grease in the tube bundle.
Stove switching off
To switch off the stove, press the key
on the control
board until you read “CLEANING FINAL ” on the display.
After the stove has been switched off, the fan continues
working for a set time in order to grant a fast smokes
exhaust from the combustion chamber.
If you have a model with remote control, you just need to
switch the remote control off keeping the key pressed for
2 seconds and confirming the selection pressing the key
SEND.
If you try to switch on the stove during this phase, the
display will show “waiting cooling ” (that means wait for
cooling) in order to inform you a switching off phase is
running. Wait until the cooling phase is completely off and
the display shows “OFF” before staring a new light up.
REMARKS:
• Do not continuously turn the stove on and off as this
could provoke sparks that could shorten the life of the
electrical components.
• Do not touch the stove with wet hands: the stove
has electrical components that could produce sparks
if handled incorrectly. Only authorized technicians can
resolve possible problems.
• Do not remove any screws from the fire chamber without
first lubricating them well.
• Never open the glass door of the pellet stove while the
stove is in operation.
• Be sure that the brazier basket is positioned correctly.
• The flue system must be suitable for inspecion. If it cannot
be removed, it must have some holes for inspection and
cleaning.
GB
Alarm signals
In the event of a working defect, the system informs the user about the type of failure occurred.
The following table summarises the alarms, kind of problem and possible solution:
"Cool fire": in the event of an even
very short lack of current, the stove
switches off. As soon as the power
supply is back, the stove will start a
cooling cycle and the display will show
the words “Cool fire”. After completing
the cooling cycle, the stove will start up
again.
NOTE: If your stove is supplied with
a remote control and there is a lack
of current, remember to program the
eventual switching on and off times
again. In the event of a lack of current,
the stove will loose any previous time
settings.
Once the power supply is back, press
the key SEND on the remote control to
retransmit the automatic programming
you previously set to the stove.
"Alarm Sond fumi": this alarm
occurs in the event the sensor for smokes
temperature is broken or not connected.
You will read the words Alarm Son fumi
on the display. In this case press the key
On/Off to reset the alarm and contact
the technical assistance.
"Alarm Dep Sic fail": this alarm is
signalised by the Leds ALF and ALC
blinking on the control board.
It indicates two different possibilities:
an obstruction in the flue or a possible
overheating of the stove. In both cases
the motor reducer to load the endless
screw stops working and the stove
switches off. Press the key On/Off to
reset the alarm. Check the possible
activation of the manual reset thermostat
on the back of the stove (4). Unscrew the
safety cap and press the key.
In the event you have the same problem
more than once, please contact the
technical assistance.
"Serv": the signal “Serv” on the display
means that the stove has reached
1200 hours working. Please contact an
authorised technical service to arrange a
supplementary maintenance.
"Alarm No acc": this alarm occurs
when the time foreseen for a light up
(around 15 minutes) passes and the
smokes temperature is still too low. This
can occur also when there is not enough
pellets flow to light up the unit. Press the
key On/Off on the control board to reset
the alarm. Wait until the cooling phase
is completed, clean the brazier and start
up with a new switching on.
"Alarm No fire": this alarm occurs in
the event the stove switches off during
its working phase (for example if there is
no pellets left in the pellets tank).
Press the key On/Off on the control
board to reset the alarm. Wait until the
cooling phase is completed, clean the
brazier and start up with a new switching
on.
Regular checks should be carried out by the user, who
should only contact the Authorized Assistance Center
if no solution is found.
1
2
3
4
1. Lighting button
2. Fuse F4AL250V
3. Thermostat reset button
4. Environmental probe
"Alarm Fan Fail": this alarm occurs
in the event the smokes ejector is broken
or the pcb cannot detect the speed of
the smokes exhaust fan.
In this case press the key On/Off to reset
the alarm and contact the technical
assistance.
16
GB
Maintenance and cleaning of the stove
Before effecting any maintenance operation or cleaning
on the stove, take the following precautions:
• be sure that all parts of the stove are cold.
• be sure that the ashes are completely cold.
• be sure that the general switch is in the “OFF” position.
• be sure that the plug is pulled out of the socket to avoid
accidental contact.
• once the maintenance phase is completed check that
everything is in order as per before the intervention (the
brazier is placed correctly).
Follow carefully the following cleaning
instructions. Failure to follow these
instructions could create problems with
the operation of the stove.
Cleaning the brazier and brazier support
When the flame assumes a red colour or seems weak, and
is accompanied by black smoke, this means that there
are ash deposits or incrustations that do not permit the
correct functioning of the stove and that must be removed.
Remove the brazier every day by simply raising it from its
slot; then clean out the ashes and eventual incrustations
that may have formed, paying particular attention to
liberating the holes by using a pointed tool (not included
with the stove).
This operation is made particularly necessary before
every lighting the first several times and above all if using
pellets that differ from those supplied by our company.
The frequency of this operation is determined by how
frequently the stove is used and the choice of pellets.
It is also a good idea to check the brazier support,
vacuuming the eventual ash present.
Ash box
Open the door and use a
vacuum to remove all the
ash deposited inside the ash
box.
This operation must be
performed more or less
frequently depending on the
quality of the pellets used.
Cleaning the glass
The glass is a self cleaning type, therefore, while the
stove is working, a veil of air is blown across its surface to
remove ash and dirt; nevertheless over a period of several
hours, a greyish patina tends to form which should be
cleaned when the stove is next shut down. How dirty the
glass becomes also depends on the quality and quantity
of pellets used.
Cleaning the glass should be done when the stove is cold
with products recommended and tested by our company.
When performing this operation, always check that the
grey seal around the glass is in a good state; failure to
check the efficiency of this gasket can compromise the
function of the stove.
Poor quality pellets can, in any case, cause the glass to
become dirty.
If the glass is broken, do not attempt to
light the stove.
Cleaning the surfaces
To clean the surfaces, use a rag dampened with water or
with water and a neutral detergent.
The use of aggressive detergents or thinners can damage the surfaces of the stove.
Before using any detergent it is advisable
to try it on a small section out of sight or contact
the Authorized Assistance Centre for information
regarding the product.
Cleaning the metal parts
To clean the metal parts of the stove, use a soft cloth
dampened with water. Never clean the metal parts with
alcohol, thinners, petrol, acetone or other degreasing
substances. If such substances are used, our company
declines any responsibility.
Eventual variations in the colour of the metal parts can be
caused by an incorrect use of the stove.
17
GB
It is necessary to daily clean the brazier
and often clean the ash box. The lack of
cleanliness can prevent the starting of the
stove, causing damages to the stove itself and to
the environment (possible emission of unbrunt
material and soot). Do not re-use the pellet possibly
remained in the brazier due to no starting-up.
• remove the electrical feed cable;
• remove the cap from the T-joint and proceed with the
cleaning of the ducts. If necessary, at least for the first few
times, call in qualified personnel;
• carefully clean the smoke discharge system: for this,
contact a professional chimney sweep;
• once a year clean the dust, cobwebs, etc. from the zone
behind the internal covering panels, paying particular
attention to the fans.
Cleaning the fans
CLEANING BY THE TECHNICAL
Check every year
Clean the combustion chamber
Remove the brazier and clean it of any residue. (photo 1)
The stove is furnished with fans (environmental and
smoke) positioned at the rear and below the stove.
Eventual deposits of dust or ash on the blades of the
fan can cause an imbalance in the fans leading to noisy
performance. It is, therefore, necessary to clean the fans
at least once a year.
Since said operation requires dismantling several parts of
the stove, have the fans cleaned only by our Technical
Assistance Centre.
Season end cleaning
At the end of the season, when the stove will not be used
for some time, it is advisable to perform a thorough and
general cleaning:
• Remove all the pellets from the container and the screw
feeder;
• Carefully clean the brazier, the brazier support, the
combustion chamber and the ash box.
1
Remove the 5 screws that secure the combustion
chamber. (photo 2)
Remove the walls of the combustion chamber and clean
the residue remaining behind this wall. (photo 3)
2
Once the preceding points have been observed, it only
means that the state of the stove has been verified. It is
necessary to thoroughly clean the smoke discharge tube
or flue and check the condition of the basket.
If necessary, order a new one from our Authorized
Assistance Centre.
If necessary, lubricate the hinges of the door and the
handle. Also check the ceramic fibre cord near the glass,
on the internal wall of the door; if it is worn or too dry,
order a new one from the Authorized Assistance Centre.
3
Cleaning the clearing system
Until a reasonable experience is acquired regarding
the operating conditions, it is advisable to perform this
maintenance on at least a monthly basis.
18
GB
Maintenance and cleaning
All cleaning of all parts must be carried out with the stove completely cold and unplugged to
avoid burns and thermal shock. The stove does not need much maintenance if used with certified
quality pellet. The need for maintenance varies depending on the conditions of use (switching on
and off repeatedly) and depending on the performance required.
Parts
Everyday
Brazier
Every 2-3
days
Every
week
Every 15
days
Every 30
days
Every 6090 days
Every year /
1200-1400 h
◊
Cleaning ash collection compartment
◊
Cleaning ash tray
◊
Cleaning the door and glass
◊
Cleaning the interior heat exchanger /
smoke fan compartment
•
Cleaning complete exchanger
Clean "T" to exhaust
•
•
Flue
•
Door gasket ash
•
Internal parts
•
Flue pipe
•
Electromechanical components
•
◊ by the user
• by the authorised qualified technical assistance
Every 1200 hours of work the electronic board sends a warning signal and the display will show
“SERVICE”. This indicates the need for a thorough cleaning of the stove by a CAT. The lack of such
cleaning could result in failure of the stove and poor combustion, thereby resulting in a lower yield.
19
GB
Safety devices
Pressure switch: monitors
depression in the smoke duct.
It is designed to shut down
the pellet feed screw in the
event of an obstructed flue or
significant back-pressure in
the presence of wind. At the
time of the pressure switch will
show “ALAR-DEP-FAIL”.
Reduction motor: if the
motor stops, the thermostove
continues to function until the
flame goes out for lack of fuel,
and until It has cooled down to
the minimum level.
Flue gas temperature sensor:
thermocouple that measures
the temperature of the fumes
while keeping the operation or
shuts the thermostove when
the flue gas temperature drops
below the preset value.
RESTART
PELLET
Electrical
safety:
the
stove is protected against
violent surges of current (ex.
lightnings) by the main fuse
4 A which is located on the
control panel at the rear of the
thermostove. Other fuses to
protect the electronic boards
are to be found on the boards
themselves.
Pellets temperature safety:
In the rare event there is a too
high temperature in the tank,
the thermostat for pellets
safety with manual reset
creates an alarm “ALAR-SICFAIL” stopping the pellet boiler
stove. You
need to reset the system
working on the device placed
on the back of the thermostove.
Room thermostat: the room
thermostat detects the present
temperature in the room. When
it detects the set temperature
on the display, the stove will
go into operation in ECO ie
hold function to save fuel.
The
room
thermostat
should be spread so as not
to be conditioned by the
temperature of the body stove.
Tampering with the safety devices is prohibited. It is only after eliminating the cause which gave
rise to the intervention of the safety system, that it is possible to relight the stove and thus reset
the automatic operation of the sensor. To understand which anomaly has occurred, consult this
manual at paragraph relating to alarms which explains what to do based on the alarm message the
stove display.
20
GB
Problems and solutions
All repairs must be carried out exclusively by a specialised technician, with the stove completely
cold and the electric plug pulled out. Is prohibited from any unauthorized modification to the
device and the replacement of parts with other non-original. The operations marked in bold type
must be carried out by specialised personnel.
Any inconvenience and solutions
Given that all stoves are tested in their parts handling and work and therefore are delivered in perfect physical condition and operation, it should be remembered that the transport, unloading, handling, misuse or poor maintenance,
can be causes of drawbacks.
The main problems may be solved by reading the table below.
If after doing as hereinafter described the problem is not resolved, contact your authorized service center.
PROBLEM
POSSIBLE CAUSE
REMEDY
Display off and buttons are not working
1. Power failure in the network
2. Switch back off
3. Display defective
4. Fault in the connection of the
display with the card
5. Fuse board interrupted
6. Card defective
1. Check that the power cord is connected
2. Use the switch back to operate it
3. Unplug the stove from the power outlet for about
one minute and then turn on. If the problem persists,
contact an authorized service center
4. Check that the display and board are properly connected. Contact your authorized service
center
5. Contact an authorized service center
6. Contact an authorized service center
Remote inefficient
1. Too far from the stove
2. No batteries in the remote
3. The remote control is broken
1. Move closer to the stove
2. Check and change the batteries
3. Replace the remote control
Failure to ignite
the stove
1. Excessive accumulation of ash
in the grate
2. Incorrect ignition procedure
1. Clean the grate
2. Repeat the ignition procedure. If the problem
persists, contact your authorized service center
Smoke comes from
the grill
1. Accidental electrical blackout
1. In case of ignition phase interrupted and momentary interruption of the fan, can occur slight amount
of smoke
Hot air fan is not
working
1. The stove has not yet been
heated
1. Wait until the conclusion of the ignition cycle.
Arrived in temperature, the fan will start automatically.
If the problem persists, contact your authorized service center.
21
GB
1. The tank is empty.
2. The resistance does not reach
the temperature
3. Resistance damaged
4. The pellet drops
5. Screw motor defective
6. The grate is not in place or is
dirty
7. Obstruction of nests or foreign
bodies in the chimney or fireplace
8. Check operation of the glow
plug
9. The ash drawer is not closed
properly
10. Clogged flue and chimney
11. Smoke extractor not working
12. Temperature sensor defective
13. Pellet wet
1. Fill the tank with pellets
2. Check the electrical wiring and fuses, replace if
the resistance is broken
3. Replace the resistance
4. It is recommended to unplug the power supply
before:
- check that the pellet is not caught in the chute
- check that the cochlea is not blocked by dirt
- check the seal of the pellet-door
5. Contact an authorized service center
6. Check that the hole in the brazier matches the
glow plug, clean brazier
7. Remove any foreign body from the chimney or flue
pipe
8. Make sure that there is power. Replace the spark
plug if burned
9. Close the drawer ashtray
10. Perform periodic cleaning
11. Check the operation of the extractor flue
12. Contact an authorized service center
13. Make sure the place of stowage pellet and replace it with a handful of dry pellets
Lock the stove.
Pellets not being fed
into the combustion
chamber
1. The tank is empty
2. The cochlea is no pellet
3. Technical problem of the
cochlea
4. Reduction motor failure
5. Electronic board faulty
1. Load the pellets in the tank.
2. Fill the tank and proceed as instructed before ignition stove
3. IT IS RECOMMENDED to unplug the power supply before:
- empty the thank and manually free the auger from
obstructions (sawdust)
- release the slide from obstructions
- remove the dust accumulation of pellets in the bottom of the tank
4. Replace the reduction motor
5. Replace the electronic board
The stove runs for a
few minutes and then
turn off
1. Lighting cycle not completed
2. Temporary failure of electricity
3. Probes fumes defective or
broken or not inserted
1. Re-run power
2. Re-run power
3. Check and replace sensors
Fume extraction fan
does not stop
1. The stove has not yet cooled
1. Allow the stove to cool. Only after cooling fan will
stop. If the problem persists, contact your authorized service center
The stove does not
turn on automatically
22
GB
The stove is clogged
early in the brazier
with burning irregular,
door glass gets dirty,
the flame is long, reddish and weak
1. Flue with presence of stretches too long or clogged
2. Too pellet
3. Excessive pellet or ash deposits in the brazier
4. The brazier is not found in its
slot
5. Wind contrary to the exhaust
flow
6. Insufficient combustion air
7. You changed the type of pellets used
8. Smoke extractor motor broken
9. Door closed incorrectly
1. Perform periodic cleaning. See paragraph stove
installation in the user manual. Check chimney
cleaning
2. Decrease in the parameters the charge level of the
pellets
3. Clean the brazier after waiting for the total shutdown of the stove. If you repeat contact your
Authorized Service Center
4. Check that the hole in the brazier matches the
glow plug
5. Check the chimney cap windproof and / or possibly install it
6. Check the correct position of the brazier, its cleanliness and check that the air intake in both free environment, verify the status of the door seal, increase
the level in the parameter relative to the speed of
the fan exhaust fumes. Contact your Authorized
Service Center
7. Check the quality of the pellets. Contact your
Authorized Service Center
8. Increase the level in the parameters relating to the
speed of the fan exhaust fumes. Check and eventually replace motor
9. Check that the glass is sealed and the seal guarantees tightness
Smell of smoke in the
environment. Turning
off the stove.
1. Poor combustion
2. Malfunction of fan fumes
3. Installation of the flue performed incorrectly
4. Clogged chimney
1. Contact your Authorized Service Center
2. Contact your Authorized Service Center
3. Contact your Authorized Service Center
4. Contact your Authorized Service Center
In the automatic position the stove always
runs at full power
1. Room thermostat set to maximum
2. Significant temperature sensor
failure
3. Control panel defective or
broken
1. Reset the thermostat temperature
2. Check the operation of the sensor and replace if
necessary
3. Check the control panel and replace if necessary
The engine smoke
extraction does not
work
1. The stove has no voltage
2. The motor is broken
3. The board is defective
4. The control panel has failed
1. Check the supply voltage and the protection fuse.
2. Check the motor and capacitor and replace if
necessary.
3. Replace the circuit board.
4. Replace the control panel.
23
GB
The fire goes out or
the stove stops automatically
1. The pellet tank is empty
2. No power
3. Pellets not being fed
4. Excessive deposit of ashes in
the grate
5. Intervention probe temperature
safety of the pellet
6. Cochlea blocked by dirt
7. The door is not closed properly or gaskets worn
8. Pellet inadequate
9. Low pellet
10. Chimney or drain clogged
with nests or foreign bodies
11. Pressure switch cuts
12. Smoke extraction motor
failure
13. Alarm active
1. Fill the tank with pellets
2. Check plug and presence electricity
3. Fill the tank with pellets
4. Clean the brazier
5. Let the stove cool down completely, reset the
manual reset and restart the stove. If the problem
persists, contact your authorized service representative
6. Pull the plug, empty the tank, remove any foreign
objects
7. Close the door or replace the gaskets with original
8. Change the type of pellet recommended by the
manufacturer. Sometimes, depending on the type,
the stage of adjustment of the parameters need
to vary the level relating to the loading of pellets
9. Increase the level in the parameter for the pellet feed. To check the flow of fuel from technical
authorized
10. Eliminate all foreign matter from the chimney
Clean the smoke duct. Perform periodic cleaning.
11. Verify potential smoke duct is blocked and if
the pressure switch is working properly
12. Check and replace the motor if necessary
13. See paragraph alarms
The air fan convention
(ambient air) never
stops
1. Temperature sensor temperature control defective or broken
2. Smoke probe fails
1. Check the operation of the sensor and replace if
necessary
2. Replace smoke probe
The stove does not
light.
1. Lack of electricity
2. Probe pellets in bulk
3. Fuse blown
4. Pressure switch broken (lockout indicated)
5. Smoke outlet or duct clogged
1. Check that the electrical outlet is plugged in and
the power switch to "I"
2. Lockout by resetting the rear thermostat, replace
the thermostat if it happens again
3. Replace the fuse
4. Replace the pressure
5. Clean the smoke outlet and / or smoke duct
The manufacturer of the stove any liability and will void the warranty terms of the product for any
inconvenience caused by not following the rules described above. Any work of service center will
be borne by the applicant if they are not complied with these instructions.
24
GB
NOTES
25
Centrometal d.o.o. Glavna 12, 40306 Macinec, Croatia
central tel: +385 40 372 600, fax: +385 40 372 611
service tel: +385 40 372 622, fax: +385 40 372 621
www.centrometal.hr
e-mail: servis@centrometal.hr
HEATING TECHNIQUE
Centrometal d.o.o. shall not be responsible for possible incorrect data caused by printing errors or error made in transcription and all figures and diagrams are for explanatory purposes only and relevant
adjustment have to be made at the spot. In any case, it reserves the right to modify its products as deemed to be required and useful without any prior notification.
Download PDF
Similar pages