5
Lock strike release
time: 50mS
1-99, #
Lock strike release
time:1-99S (default
5S)
0, #
Type A electronic
lock④
1, #
Type B electronic
lock ⑤ (default)
Reader mode settings
Flash Flash
Red
Red Red and Green
Green
Function
0, #
2, #
5.1 To unlock the door for card users,
Read valid card once, the electronic lock will unlock
5.2 To unlock the door for card and PIN users
Read valid card once then enter 4-6 digits PIN#, the lock will unlock
5.3 To unlock the door for card or PIN users
Read valid card once, the lock will unlock
Or enter 4-6 digits PIN#, the lock will unlock
5.4 To change the PIN of a PIN user
*, Read Card, input 4-6 digits old PIN , #, input 4-6 digits new PIN,
#, repeat input 4-6 digits new PIN, #.
or*, Input 1-500 (ID), #, input 4-6 digits old PIN, #, input 4-6 digits
new PIN, #, repeat input 4-6 digits new PIN, #.
LOCK-
LOCK+
D_IN(LED)
OPEN(BZ)
D1
D0
GND
+12V
LOCK-
LOCK+
OPEN(BZ)
D1
D0
GND
+12V
Operation Status
Standby
Press Key
Read Card
Door Open
Operation Successful
Operation failed
PIN Inputting
Card & PIN inputting
1st menu
2nd menu
Under Setting
Alarm
Remark: For PIN users without card, must get ID number and
initial PIN from the master. For users with card, must read card to
change initial PIN.
40uS
0V
6.2 Magnetic Contact Switch on the Door
While connecting to a door position switch, if door-forced
conditions are supported, the buzzer alarm will activate if the
door is forced open..
6.3 Remove the alarm
While anti-tamper and door status alarm is valid, read valid card,
or input master code can remove the alarm. The alarm will also
stop after 1 min if there is no operation.
Green LED
OFF
OFF
OFF
OFF
ON
ON
ON
Slow flash
Slow flash
Slow flash
Slow flash
ON
Quick flash
OFF
OFF
OFF
Slow flash
ON
OFF
40uS
0V
Buzzer
Short Ring
Long Ring
Long Ring
Long Ring
3 Short Ring
There are 3 formats for the card output by Wiegand 26.
Format 0: 4-6 digits key press sends card number format: Input
4-6 digits PIN, press “#”, output a Wiegand 26, 10-bit decimal
card number. For example, input password 999999, the output
card number is 0000999999, could be displayed by 10-bit
decimal card number display equipment.
Format 1: Each key press sends 4 bits data, the corresponding
relationship is:
Alarm
1
4
7
*
(0001) ,
(0100) ,
(0111) ,
(1010) ,
2 (0010) ,
5 (0101) ,
8 (1000) ,
0 (0000) ,
3 (0011)
6 (0110)
9 (1001)
# (1011)
Format 2: Each key press sends 8bit output data, the first 4 digits
is ones-complement code for the last 4 digits, the corresponding
relationship is:
Reader Mode
Red
2mS
D1 +5V
8. Reader Application (wiring diagram)
6. Alarm
6.1 Anti Tamper Alarm
While anti-tamper function is valid, if the access control unit is
removed from the cover, the buzzer alarm will activate.
Red LED
ON
2mS
D0 +5V
Reset to factory default, the users' information is still retained.
8. Sound and Light Indication
5. User Settings
1
4
7
*
(11100001) ,
(10110100) ,
(10000111) ,
(01011010) ,
2 (11010010) , 3 (11000011)
5 (10100101) , 6 (10010110)
8 (01111000) , 9 (01101001)
0 (11110000) , # (01001011)
Black Green White Brown Yellow Orange Blue
+12V GND
D0
LED
D1
BZ
Access Control
Set the unit to reader application, functions as below:
4
5
Function
Master mode
(default 888888)
The wire in green (D0) is the wire for Wiegand 0, and the wire
in white is the wire for wiegand 1. The pulse width for low voltage
is 40uS; and the time interval is 2mS.
LOCK-
4
0, #
1, #
Flash Red
7. Reset to Factory Default
Power off, press *, power on, the red and green LED will turn on,
release it until hear two beeps, then will hear one beep and the
red LED will turn on, resets to factory default setting is done.
LOCK+
2, #
3
Reader mode
Access control mode (default)
4-6 digits key press sends card
number
Each key press sends 4bit output
data (default)
Each key press sends 8bit output
data
OPEN(BZ)
To unlock by
card and PIN
To unlock by card
or PIN (default)
1, #
0, #
1, #
D_IN(LED)
3
7
1
Red
3
D1
0, #
⑤ Type B electronic lock: Fail Safe lock(Unlock when power off),
such as EM Lock, Electronic Bolt Lock, etc.
2
D0
Delete all users
and PIN
To unlock by card
0000, #
④ Type A electronic lock: Fail Secure lock(Unlock when power
on), such as Electronic Controlling Lock.
6-8 digits master PIN,#
GND
2
③ After one card is added , you can continue to add other cards
or PIN without exiting the mode.
Wiring diagram (special power supply for access control)
+12V
1-500 (ID) , #
B Lock
8 or 10 digits card number, #
Open Door delay
0(50ns) for type A lock
A Lock
Read card
Lock
Add one user PIN,
or add more than
1 users PIN
Delete one card,
or delete more
than 1 cards
Delete one user,
or delete more
than one users
1-500 (ID) , #, 4-6 digits user
PIN, #
1
Add one card②,
or add more than
1 cards③
Exit Button
0
Change
master PIN
② A PIN 1234 is added for a card, it can not be used to unlock the
lock, can be used to change PIN.
PUSH +12V GND NO COM NC
Red Black Green White Brown Yellow Orange Blue
Door Contact
Electronic lock schematic diagram
Access control mode settings
6-8digits new PIN, #,
repeat 6-8digits new PIN, #
Read card
1-500 (ID) , #, Read card
8 or 10 digits card number①,
1-500 (ID) , #, 8 or 10 digits card
number, #
special power supply
Master Operation
Access Control Black
Keypad / Reader Card Reader
Standalone No Software 500 Users
0
Exit Button
Door Contact
VIS-3012
Standalone Access Control
VIS-3012
Function
+12V Power Input
GND
Wiegand output D0
Wiegand output D1
Green light input
Buzzer input
Remark:
① 8 digits card number, such as 118,32319, some cards has no
mark of the first 3 digits 118, remains 32319. It requires to add
card by read card, adding cards by input card number is not
acceptable;10 digits card number, such as 0007765567, some
cards has no mark of the first 3 digits 000, remains 7765567,
requires to input 10 digits 0007765567 by add 000 before
7765567.
Wiring diagram (DC 12V power supply)
LOCK-
Red and Green LED ON
Description
+12V DC
GND
D0
D1
LED
Buzzer
Enter Master Operation Mode. It will return to normal mode if
there is no right Master PIN input in 5 seconds. After input of right
master PIN, it will also return to normal mode if there is no valid
operation in 30 seconds. Press “#” to confirm the input number,
return to previous menu by press “*”, the LED will indicate the
operation mode.
DC12V
Power
2.Installation and Wiring Instructions
Flash
Red
Functionality
4. Master keypad Operation
1.3 Specifications
> Operating voltage range: DC12-24V
> Static input current: ≤ 20mA
> Max proximity card read range: 5-8cm (1.96 – 3.14in.)
> Excitation Frequency: 125KHz
> Card transmit format: Wiegand 26
> Keypad transmit format: 4-6 digits key press to output card number
format. Each press outputs a 4 bits or 8 bits data.
> Size: 90(L) x 60(An) x 27(Al)mm – 3.54(L) x 2.36(An) x 1.06(Al) in.
> Operating temperature range : -40°C~60°C (-4°F~140°F)
> Operating humidity: 0∼95% (non-condensing)
LOCK+
Color
Red
Black
Green
White
Brown
Yellow
Black Green White Brown Yellow Orange Blue
Red
1.2 Features
Backlit keypad, multi-function, operating as access control or card
reader, suitable for various occasions.
+12V
3. Wiring Definition
VIS-3012 Standalone Access Control
D_IN(LED)
INSTRUCTION
MANUAL
1. Introduction, Features and Specifications
1.1 Introduction
VIS-3012 is a standalone, convertible integrated reader and
access control. It controls electronic lock, exit button, and the
magnetic contact switch on the door. If the unit is connected to a
standard access control unit, then it functions as a reader. The
unit accepts up to 500 users, allow entry via a 4-6 digits PIN
and/or by presenting a proximity EM card.
6
7
Download PDF
Similar pages