Instructions - GB
Instrucțiuni de utilizare - RO
Anleitung - D
Eredeti használati utasítás - HU
Ръководство за употреба - BG
Instrukcja obsługi - PL
www.heinner.com
VMF001
GASOLINE CHAIN SAW
SAFETY FIRST
Instructions contained in warnings within this manual marked with a symbol concern critical points which
must be taken into consideration to prevent possible serious bodily injury, and for this reason you are
requested to read all such instructions carefully and follow them without fail.

NOTES ON TYPES OF WARNINGS IN THE MANUAL
WARNING
This mark indicates instructions which must be followed in order to prevent accidents which could lead to
serious bodily injury or death.
IMPORTANT
This mark indicates instructions which must be followed, or it leads to mechanical failure, breakdown or
damage.
NOTE
This mark indicated hints or directions useful in the use of the product.
CONTENTS
1. PARTS LOCATION ............................................................................................................................ 3
2. WARNING LABELS ON THE MACHINE .............................................................................................. 3
3. SYMBOLS ON THE MACHINE ........................................................................................................... 4
4. SAFETY PRECAUTIONS .................................................................................................................... 4
5. INSTALLING GUIDE BAR AND SAW CHAIN ....................................................................................... 7
6. FUEL AND CHAIN OIL ...................................................................................................................... 8
7. OPERATING THE ENGINE ................................................................................................................. 9
8. SAWING ....................................................................................................................................... 12
9. MAINTENANCE .............................................................................................................................. 14
10. MAINTENANCE OF SAW CHAIN AND GUIDE BAR ......................................................................... 16
11. SPECIFICATIONS .......................................................................................................................... 17
2
GASOLINE CHAIN SAW
1. PARTS LOCATION
1 - Front guard
2 - Starter knob
3 - Air cleaner
4 - Choke knob
5 - Throttle lever
6 - Right handle
7 - Throttle lever
8 - Throttle lock button
9 - Engine switch
10 - Fuel tank
11 - Oil tank
12 - Left handle
13 - Saw chain
14 - Guide bar
2. WARNING LABELS ON THE MACHINE
(1) Read owner’s manual before operating this machine.
(2) Wear head, eye and ear protection.
(3) Use the chain saw with two hands.
(4) Warning! Kickback danger.
(5) Warning/Attention
3
GASOLINE CHAIN SAW
IMPORTANT
If warning seals peel off or become soiled and impossible to read. you should contact the dealer from
which you purchased the product to order new seals and affix the new seals in the required location.
WARNING
Never remodel the product. We won’t warrant the machine, if you use the remodeled product or you
don’t observe the proper usage writer in the manual.
3. SYMBOLS ON THE MACHINE
For safe operation and maintenance. symbols are carved in relief on the machine.
According to these indications, please be careful not to take a mistake.
(a). The port to refuel the “MIX GASOLINE”
Position: fuel tank cap
(b). The port to refuel the “CHAIN OIL”
Position: oil cap
(c). The indication regarding the switch.
Flipping the engine switch to the “o” (STOP)direction, the engine stops.
Position: rear-left of the unit
(d). The indication regarding the choke.
Pulling out the choke knob, the choke closes.
Position: rear-right of the unit
(e). The indication regarding the chain oil adjuster nut.
“MIN” direction-the oil flow decrease
“MAX” direction-the oil flow increase
Position: bottom of the clutch side
(f). The position of H-needle
The position of L-needle
The position of idle adjusting screw
Position: rear-left of the unit
4. SAFETY PRECAUTIONS
 BEFORE USING THE MACHINE
a. Read this owner’s manual carefully to understand how to operate this unit properly.
b. You should never use the product alcohol, when suffering from exhaustion or lack to sleep, when suffering
from drowsiness as a result of having taken cold medicine, or at any other time when a
possibility exists that your judgment might be impaired or that you might not be able to
operate the machine property and in a safe manner.
c. Avoid running the engine indoors. The exhaust gases contain harmful carbon monoxide.
d. Never use the product under circumstances like those described below:
1. When the ground is slippery or which might make it not possible to maintain a steady
posture.
2. At night, at times of heavy fog, or at any other times when your field of vision might be
limited and it would be difficult to gain a clear view of the area.
3. During rain storms, during lightning storms, at times of any other times when weather
conditions might make it unsafe to use this product.
e. When using this product for the first time, before beginning actual work. Learn to handing
4
GASOLINE CHAIN SAW
it from skilled worker.
f. Lack of sleep, tiredness or physical exhaustion results in lower attention spans, and this in turn leads to
accidents and injury. Limit the amount of time of using the machine continuously to somewhere around 10
minutes per session, and take 10-20 minutes or rest between work sessions. Also try to keep the total single
day under 2 hours or less.
g. Be sure to keep this manual handy so that you may refer to it later whenever any questions arise.
h. Always be sure to include this manual when selling, lending, or otherwise transferring the
ownership of this product.
i. Never allow children or anyone unable to fully understand the directions given in this manual
to use this product.
 WORKING GEAR AND CLOTHING
a. When using the product, you should wear proper clothing and protective equipment at follows.
(1) Helmet
(2) Protection goggles or face protector
(3) Thick work gloves
(4) Non-slip-sole work boots
(5) Ear protectors
b. And you should carry with you.
1. Attached tools and files.
2. Properly preserved fuel and chain oil.
3. Things to notify your working area (rope, warning signs)
4. Whistle (for collaboration or emergency)
5. Hatchet or saw (for removal of obstacles)
c. Never use the product when wearing pants with loose cuffs. when wearing pants with loose
cuffs. when wearing sandals. or when barefoot.

WARNING CONSIDERING HANDLING OF FUEL
a. The engine of this product is designed to run on a mixed fuel which contains highly
flammable gasoline. Never store cans of fuel or refill the fuel tank in any place where there
is a boiler, stove, welding sparks, or any other source of heat or fire which might ignite the
fuel.
b. Smoking while operation the product or refilling its fuel tank is sure to keep lit cigarettes away from the
product at all times.
c. When refilling the tank always turn off the engine first and take a careful look around to make sure that
there are no sparks or open flames anywhere nearby before refueling.
d. If any fuel spillage occurs during refueling, use a dry rag to wipe u spills before turning the engine back
on again.
e. After refueling, screw the fuel cap back tightly onto the fuel tank and then carry the product to a spot 3M
or more away from where it was refueled before turning on the engine.

BEFORE STARTING ENGINE
 Check working place, the cutting object and cutting direction. if there is obstacle, remove it.
 Never start cutting until you have a clear work area. secure footing and a planned retreat path from
the falling tree.
 Use caution and keep bystanders and animals out of the working area whose diameter is 2.5 times
5
GASOLINE CHAIN SAW
of the cutting object.
 Inspect the machine for worn, loose, or damaged parts. Never operate the machine that is
damaged, improperly adjusted, or is not completely and securely assembled. Make sure that the
saw chain stops moving when the throttle control trigger is released.

WHEN STARTING THE ENGINE
 Always hold the machine firmly with both hands when the engine is running. Use a firm grip with
thumb and fingers encircling the handles.
 Keep all parts of your body away from the machine when the engine is running.
 Before starting the engine, make sure the saw chain is not contacting anything.

OPERATION
 Keep the handles dry, clean and free of oil or fuel mixture.
 Never touch the muffler, spark plug or other metallic parts of the engine while
the engine is in operation or immediately after stopping the engine. Doing so
could result in serious burns or electrical shock.
 Use extreme caution when cutting small size brush and saplings because
slender material may catch the saw chain and be whipped toward you or pull
you off balance.
 When cutting a limb that is under tension, be alert for spring back so that you
will not be struck when the tension in the wood fibers is released.
 Check the tree for dead branches that could fall during the felling operation.
 Always shut of the engine before setting it down.

KICKBACK SAFETY PRECAUTIONS FOR CHAIN SAW USERS
WARNING
 Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in
and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning fast reverse reaction.
kicking the guide bar up and back towards the operator. Pinching the saw chain along the top of the guide
bar may push the guide bar rapidly back towards the operator. Either of these reactions may cause you
to lose control serious personal injury.
 Do not rely exclusively on the safely devices built into your saw. As a chain saw user you should take
several steps to keep cutting jobs free from accident or injury.
(1) With a basic understanding of kickback, you can reduce or eliminate the element of surprise. Sudden
surprise contributes to accidents.
(2) Keep a good grip on the saw with both hands, the right hand on the rear handle, and the left hand on
the front handle, when the engine is running. Use a firm grip with thumbs and fingers encircling the
chain saw handles. A firm grip will help you reduce kickback and maintain control of the saw.
(3) Make certain that the area in which you are cutting is free form obstructions. Do not let the nose of the
guide bar contact a log, branch, or and other obstruction which could be hit while you are operating the
saw.
(4) Cut at high engine speeds.
(5) Do not overreach or cut above shoulder height.
(6) Follow manufactures sharpening and maintenance instructions for saw chain.
(7) Only use replacement bars and chains specified by the manufacturer or the equivalent.
6
GASOLINE CHAIN SAW

MAINTENANCE
 In order to maintain your product in proper working order, perform the maintenance and checking
operations described in the manual at regular intervals.
 Always be sure to turn off the engine before performing any maintenance or checking procedures.
WARNING
The metallic parts reach high temperatures immediately after stopping the engine.
 Leave all maintenance other than the items listed in the owner’s manual to your
competent servicing dealer.

TRANSPORTATION
 Always carry the unit with the engine stopped, the guide bar covered with the protector to the rear,
and muffler away from your body.
5. INSTALLING GUIDE BAR AND SAW CHAIN
A standard saw unit package contains the items as illustrated. (F1)
(1) Power unit
(2) Bar protector
(3) Guide bar
(4) Saw chain
(5) Plug wrench
(6) Screwdriver for carburetor adjustment
(7) Spike and mounting screws
Open the box and install the guide bar and the saw chain on the power unit as follows:
WARNING
The saw chain has very sharp edges. Use thick protective gloves for safety.
1. Pull the guard towards the front handle to check that the chain brake is not on.
2. Loosen the nuts, and remove the chain cover.
3. Install the attached spike to the power unit.
4. Gear the chain to the sprocket and while fitting the saw chain around the guide bar, mount the guide bar
to the power unit. adjust the position of chain tensioner nut on the chain cover to the lower hole of guide
bar. (F2)
(8) Hole
(9) Tensioner nut
(10) Chain cover
NOTE
Pay attention to the correct direction of the saw chain. (F3)
(1) Moving direction
7
GASOLINE CHAIN SAW
5. Fit the chain cover to the power unit and fasten the nuts to finger tightness.
6. While holding up the tip of the bar, adjust the chain tension by turning the tensioner screw until the tie
straps just touch the bottom side of the bar rail. (F4)
7. Tighten the nuts securely with the bar tip held up (12-15 Nm). Then
check the chain for smooth rotation and proper tension while moving it
by hand. If necessary, readjust with the chain cover loose.
8. Tighten the tensioner screw.
(2) Loosen
(3) Tighten
(4) Tensioner screw
NOTE
A new chain will expand its length in the beginning of use. Check and readjust the tension frequently as a
loose chain can easily derail or cause rapid wear of itself and the guide bar.
6. FUEL AND CHAIN OIL
 FUEL
Mix a regular grade gasoline (leaded or unleaded, alcohol-tree) and a quality proven motor oil for air cooled
2 cycle engines.
Recommended mixing ratio:
Condition
Up to 20 hours use
After 20 hours use
25:1 mix chart
Gasoline (liters)
2-cycle oil (ml)
Gasoline : Oil
20:1
25:1
1
40
2
80
3
120
4
160
5
200
WARNING
 Keep open flames away from the area where fuel is handled or stored.
 Mix and store fuel only in an approved gasoline container.
NOTE
Most engine troubles are caused, directly or indirectly, by the fuel used on the machine. Take special care
not to mix a motor oil for 4 cycle engines.

CHAIN OIL
Use motor oil SAE # 10 W-30 all year round or SAE #30 - #40 in summer, and SAE #20
in winter.
NOTE
Do not use wasted or regenerated oil that can cause damage to the oil pump.
8
GASOLINE CHAIN SAW
7. OPERATING ENGINE
 STARTING ENGINE
1. Fill fuel and chain oil tanks respectively, and tighten caps
securely. (F7)
2. Put the switch to “l” position. (F8)
3. While holding the throttle interlock. push in the side throttle
lock button and release the throttle lever to hold it at the starting
position. (F9)
(1) Chain oil
(2) Fuel
(3) Switch
(4) Throttle lock button
(5) Throttle lever
(6) Throttle interlock
(7) Chock knob
4. Pull out the chock knob to the closed position. (F10)
NOTE
When restarting immediately after stopping the engine, leave the
choke knob at the open position.
5. While holding the saw unit securely on the ground, pull the
starter rope vigorously. (F11)
WARNING
Do not start the engine while hanging the chain saw with a
hand. The saw chain may touch your body. It’s very dangerous.
6. When engine has ignited first, push in the choke knob and pull
the starter again to start the engine.
7. Allow the engine to warm up with the throttle lever pulled
slightly.
WARNING
Keep clear of the saw chain as it will start rotating upon starting
of engine.
 CHECKING OIL SUPPLY
After starting the engine, run the chain at medium speed and see
if chain oil is scattered off as shown in the figure. (F12)
(1) Chain oil
9
GASOLINE CHAIN SAW
The chain oil flow can be changed by inserting a screwdriver in the hole on
bottom of the clutch side. Adjust according to your work conditions. (F13)
(1) Adjuster
NOTE
The oil tank should become nearly empty by the time fuel is used up. Be sure to refill the oil tank every time
when refueling the unit.
 ADJUSTING CARBURETOR (F14)
The carburetor on your unit has been factory adjusted, but may require fine
running due to change in operating condition. Before adjusting the carburetor,
make sure that provided are clean air/fuel filters and fresh, properly mixed
fuel. When adjusting, take the following steps:
NOTE
Be sure to adjust the carburetor with the bar chain attached.
1. Stop engine and screw in both H and L needles until they stop. Never force. Then set them back the initial
number of turns as shown below.
H needle: 1 ⅜
L needle: 1 ¼
2. Start engine and allow it to warm up at half-throttle.
3. Turn L needle slowly clockwise to find a position where idling speed is maximum, then set the needle back
a quarter (1/4) turn counterclockwise.
4. Turn idle adjusting screw (T) counterclockwise so that saw chain does not turn, If idling speed is too slow,
turn the screw clockwise.
5. Make a test cut and adjust the H needle for best cutting power, not for maximum speed.
(1) L needle
(2) H needle
(3) Idle adjusting screw
 CARBURETOR ANTI-FREEZE MECHANISM
Operating the chain saw in temperatures of 0-5 °C at times of high humidity may result in ice forming within
the carburetor, and forming within the carburetor, and this in turn may cause the output power of the engine
to be reduced or for the engine to fail to operate smoothly. This product has accordingly been designed with
a ventilation hatch the back of the air cleaner cover to allow warm air to be supplied to the engine and to
thereby prevent icing from occurring. Under normal circumstances, the product should be used in normal
operating mode, i.e. in the mode to which it is set at the time of shipment. However, when the possibility
exists that icing may occur, the unit should be set to operate in anti-freeze mode before use. (F15)
10
GASOLINE CHAIN SAW

HOW TO SWITCH BETWEEN OPERATING MODES (F15)
1. Flip the engine switch to turn off the engine.
2. Remove the air cleaner cover form the cylinder cover
3. Loosen a screw and remove the screen on the back of the air cleaner cover.
4. Reattach the screen right side left so as to the anti-icing plate if on the right.
Reinstall the cover.
(1) Air cleaner cover
(2) Anti-icing plate
(3) Screw
(4) Normal operating mode
(5) Anti-freeze mode
(6) Screen
WARNING
Continuing to use the product in anti-freeze mode even when temperatures have risen and returned to
normal may result in the engine falling to start properly or in the engine falling to operate at its normal
speed. And for this reason, you should always be sure to return the unit to normal operating mode if there
is no danger of icing occurring.
When using the saw with the anti-freeze mode, frequently check the screen and keep it clean of saw dust.
 CHAIN BRAKE
This machine is equipped with an automatic brake to stop saw chain rotation
upon occurrence of kickback while in saw cutting operated. by inertial force
which acts on the weight fitted inside the front guard. This brake can also be
operated manually with the front guard turned down to the guide bar. (F16)
To release brake, pull up the front guard toward the front handle till “click” sound
is heard.
IMPORTANT
Be sure to confirm brake operation on the daily inspection.
How to confirm:
(1) Turn off the engine.
(2) Holding the chain saw horizontally. release your hand from the front handle.
hit the tip of the guide bar to a stump or a piece of wood. and confirm brake
operation. Operating level varies by bar size. (F17)
In case the brake is not effective. ask our dealer inspection and repairing. The
engine, if being kept rotated at high speed with the brake engaged. heats the
clutch. causing a trouble. When the brake is operated while in operation,
immediately release your fingers form the throttle lever and keep the engine
idling.
11
GASOLINE CHAIN SAW
 STOPPING ENGINE
1. Release the throttle lever to allow the engine idling for a few minutes
2. Put the switch to the “O”(stop) Position. (F18)
(1) Switch
8. SAWING
WARNING
 Before proceeding to your job, read “For Safe Operation” section it is recommended to first practice
sawing easy logs. This also helps you get accustomed to your unit.
 Always follow the safety regulations. The chain saw must only be used for cutting wood. It is forbidden to
cut other types of material. Vibrations and kickback vary with different materials and the requirements of
the safety regulations would not be respected. Do not use the chain saw as a lever for lifting, moving or
splitting objects. Do not lock it over fixed stands. It is forbidden to hitch tools or applications to the p.t.o.
that are not specified by the manufacturer.
 It is not necessary to force the saw into the cut. Apply only light pressure while running the engine at full
throttle.
 When the saw chain is caught in the cut, do not attempt to pull it out by force, but use a wedge or a lever
to open the way.
 GUARD AGAINST KICKBACK (F19)
 This saw is equipped with a chain brake that will stop the chain in the event of kickback
if operating properly. You must check the chain brake operation before each usage by
running the saw at full the throttle for 1-2 seconds and pushing the front hand guard
forward.
 The chain should stop immediately with the engine at full speed. If the chain is slow
to stop or does not stop. replace the brake hand and clutch drum before use.
 It is extremely important that the chain brake be checked for proper operation before
each use and that the chain be sharp in order to maintain the kickback safely lever of this saw. Removal
of the safety devices. Inadequate maintenance. or incorrect replacement of the bar or chain may increase
the risk of serious personal injury due to kickback.
 FELLING A TREE (F20)
1. Decide the felling direction considering the wind, lean of the tree, location of heavy
branches, ease of job after felling and other factors.
2. While cleaning the area around the tree, arrange a good foothold and retreat path.
3. Make a notch cut one-third of the way into the tree on the felling side.
4. Make a felling cut from the opposite side of the notch and at a level slightly higher
than the bottom of the notch.
12
GASOLINE CHAIN SAW
WARNING
When you fell a tree, be sure to warn your neighboring workers of the danger.
(1) Notch cut
(2) Felling cut
(3) Felling direction

BUCKING AND LIMBING
WARNING
 Always ensure your foothold. Do not stand on the leg.
 Be alert to the rolling over of a cut log. Especially when working on a slope, stand on the uphill side of the
log.
 Follow the instructions in “For Safe Operation” to avoid kickback of the saw.
Before starting work, check the direction of bending force inside the log to be cut. Always finish cutting from
the opposite side of bending direction to prevent the guide bar from being caught in the cut.
A Log lying on the ground (F21)
Saw down halfway, then roll the log over and cut from the opposite side.
A Log hanging off the ground (F22)
In area A, saw up from the bottom one-third and finish by sawing down form the
top. In area B, saw down from the top one-third and finish by sawing up from the
bottom.
Cutting limb of Fallen Tree (F23)
First check to which side the limb is bent, then make the initial cut from the bent
side and finish by sawing from the opposite side.
WARNING
Be alert to the spring back of a cut limb.
Pruning of Standing Tree (F24)
Cut up from the bottom, finish down form the top.




WARNING
Do not use an unstable foothold or ladder.
Do not overreach.
Do not cut above shoulder height.
Always use your both hands to grip the saw.
13
GASOLINE CHAIN SAW
9. MAINTENANCE
WARNING
Before cleaning, inspecting or repairing your unit, make sure that engine has stopped and is cool.
Disconnect the spark plug to prevent accidental starting.

MAINTENANCE AFTER EACH USE
1. Air filter
Dust on the cleaner surface can be removed by tapping a comer of the cleaner against
a hard surface. To clean dirt in the meshes. Split the cleaner into halves and brush in
gasoline. When using compressed air, blow from the inside. (F25)
NOTE
When installing the main filter, make sure that the grooves on the filter edge are
correctly fit with the projections on the cylinder cover.
2. Oiling port
Dismount the guide bar and check the oiling port for clogging. (F26)
(1) Oiling port
3. Guide bar
When the guide bar is dismounted, remove sawdust in the bar groove and the oiling
port. (F27)
Grease the nose sprocket form the feeding port on the tip of the bar. (F28)
(1) Oiling port
(2) Grease port
(3) Sprocket
4. Others
Check for fuel leakage and loose fastenings and damage to major parts, especially handle joints and guide
bar mounting. If any defects are found, make sure to have them repaired before operation again.

PERIODICAL SERVICE POINTS
1. Cylinder fins
Dust clogging between the cylinder fins will cause overheating of the engine.
Periodically check and clean the cylinder fins after removing the air cleaner and the
cylinder cover. When installing the cylinder cover, make sure that switch wires and
grommets are positioned correctly in place. (F29)
NOTE
Be sure to block the air intake hole.
14
GASOLINE CHAIN SAW
2. Spark plug (F30)
Clean the electrodes with a wire brush and reset the gap to 0.65 mm as necessary.
3. Sprocket (F31)
Check for cracks and for excessive wear interfering with the chain drive. If the wearing is found obviously.
Replace it with new one. Never fit a new chain on a worn sprocket, or a worn chain on a new sprocket.
(1) Sprocket
(2) Needle bearing
(3) Clutch drum
(4) Spacer
(5) Clutch shoe
4. Fuel filter
(a) Using a wire hook, take out the filter from the filler port. (F32)
(b) Disassemble the filter and wash with gasoline, or replace with new one if needed.
(1) Fuel filter
NOTE
 After removing the filter, use a pinch to hold the end of the suction pipe.
 When assembling the filter, take care not to allow filter fibers or dust inside
5. Oil tank
With a wire hook, take out the oil filter through the filler port and clean in gasoline. When putting the filter
back into the tank, make sure that it comes to the front right corner. Also clean off dirt in the tank. (F33)
(2) Oil filter
6. Front and Rear dampers
Replace if adhered part is peeled or crack s observed on the rubber part.
15
GASOLINE CHAIN SAW
10. MAINTENANCE OF SAW CHAIN AND GUIDE BAR

SAW CHAIN
WARNING
It is very important for smooth and safe operation to keep the cutters always sharp.
Your cutters need to be sharpened when:
 Sawdust becomes powder-like.
 You need extra force to saw in.
 The cut way does not go straight.
 Vibration increase.
 Fuel consumption increases.
Cutter setting standards:
WARNING
Be sure to wear safety gloves.
Before filing:
 Make sure the saw chain is held securely.
 Make sure the engine is stopped.
 Use a round file of proper size for your chain.
File size: 3/16 in (4.76 mm).
Place your file on the cutter and push straight forward. Keep the file position as
illustrated. (F34)
After every cutter has been set. Check the depth gauge and file it to the proper
level as illustrated. (F35)
WARNING
Be sure to round off the front edge to reduce the chance of kickback or tie-strap
breakage.
(1) Appropriate gauge checker
(2) Make the shoulder round
(3) Depth gauge standard
Make sure every cutter has the same length and edge angles as illustrated (F36)
(4) Cutter length
(5) Filing angle
(6) Side plate angle
(7) Top plate cutting angle
16
GASOLINE CHAIN SAW
 GUIDE BAR
 Reverse the bar occasionally to prevent partial wear.
 The bar rail should always be a square. Check for wear of the bar rail. Apply a ruler to the bar and the
outside of a cutter. If a gap is observed between them, the rail is worn. Such a bar needs to be corrected
or replaced. (F37)
(1) Ruler
(2) Gap
(3) No gap
(4) Chain tilts
11. SPECIFICATIONS*
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Displacement (cm3)
Fuel
Fuel tank capacity (ml)
Chain oil
Oil tank capacity (ml)
Ignition system
Carburetor
Spark plug
Oil feeding system
Sprocket
Guide bar type
Guide bar size(in)
Saw chain pitch (in)
Saw chain gauge (in)
58
Mixture (Gasoline 25 : Two-cycle oil 1)
550
Motor oil SAE#10W-30
260
Pointless (CDI)
Walbro
XIAHUI L7T
Automatic pump with adjuster
(Teeth x Pitch): 0.325
Sprocket nose
20”
0.325
0.058
*Specifications are subject to change without notice.
RECYCLING
Electrical and electronic equipment waste (WEEE) might contain dangerous materials which can have a
negative impact on the environment and human health if not collected separately.
This item is in conformity with the European Directive EU WEEE (2012/19/EU) and is marked with an
electronic and electrical waste logo graphically represented in the image below.
This icon shows that WEEE should not be collected with household waste but separately.
We recommend you to consider the following:
- Materials and components used when manufacturing this item are high quality materials
which can be reused and recycled;
17
GASOLINE CHAIN SAW
- Do not throw away the item with household waste at the end of life;
- Take the item to a collecting point where it will be collected for free;
- Please contact the local authorities for details on the collecting centers.
Conformity with the RoHS Directive: the item you purchased is in conformity with the EU Directive RoHS
(2011/65/UE). It does not contain materials listed as harmful or prohibited in the Directive.
Thank you for helping us protect the environment and our health!
Manufactured for
Network One Distribution
Marcel Iancu St., no. 3-5, Bucharest, 020757
2017
18
Download PDF
Similar pages