quick shave pro rotary shaver

QUICK SHAVE PRO
ROTARY SHAVER
USE & CARE
MANUAL
PLEASE READ
PRIOR TO USE
To register your product go to
remington-products.com.au
remington.co.nz
2 YEAR WARRANTY
XR1415AU
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should
always be observed, including the following.
READ ALL INSTRUCTIONS BEFORE USING
For additional protection, the installation of a residual
current device (rcd) having a rated residual operating
current not exceeding 30 mA is advisable in the electrical
circuit supplying the bathroom. Ask your installer for advice.
WARNING: To reduce the risk of burns, electrocution and
fire or injury to persons.
DANGER: As with most electrical appliances, electrical
parts are electrically live even when the switch is off.
• The appliance should never be left unattended when plugged
into a power outlet, except when charging the appliance.
• This appliance should not be used by children or other
persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge unless they have
been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning
and use maintenance shall not be made by children without
supervision.
• Never operate this appliance if it has a damaged cord or
plug, if it is not working correctly, if it has been dropped or
damaged, or dropped into water. If the supply cord or plug
of the appliance is damaged it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard. It cannot be repaired. Keep the
cord away from heated surfaces.
• Charge, use and store the product at a temperature between
0°C and 32°C.
2
• Do not use outdoors or where aerosol (spray) products are
being used, or where oxygen is being administered.
• Do not use this appliance with damaged or broken tracks or
cutters, as injury may occur.
• Do not plug or unplug the appliance with wet hands.
• For household use only.
• Do not place or store the appliance or charging adaptor
where it can fall or be knocked into a sink or bath.
• Do not place in or drop into water or any other liquid.
• If an appliance falls into water, “unplug it” immediately. Do
not reach into the water.
• Unplug the charging adaptor from the electrical outlet
immediately after fully charging.
• Unplug and switch off this appliance before cleaning it.
• Use this appliance only for its intended use as described in
this manual.
• Do not use attachments not recommended by Remington.
• Never drop or insert any object into any opening of this
appliance.
• Always store the charging adaptor in a moisture-free
location.
• Do not use on people who are asleep.
• Do not use an extension cord or a voltage converter with this
appliance.
• Do not wrap the cord around the appliance.
Remington strongly recommends that an approved Safety Switch
(residual current device) be installed to protect all bathroom power
outlets. Ask an electrical contractor for advice.
SAVE THESE INSTRUCTIONS
3
XR1415AU QUICK SHAVE PRO ROTARY SHAVER USE & CARE MANUAL
Thank you for purchasing your new Remington® Quick Shave Pro Rotary Shaver.
Inside this manual you will find tips on using and caring for your shaver.
1
2
3
8
5
6
7
4
9
10
11
12
13
KEY PARTS
1.
2.
3.
4.
5.
6.
7.
8.
9.
Rotary shaver head
Pop-up detail trimmer
(not shown)
Main body
Charging pins
On/off button
Battery indicator display
Trimmer head
Adjustable comb
Storage bag
10.
11.
12.
13.
Deep cleansing brush
Brush mount
Daily cleansing brush
Pre-shave brush
Also Includes:
• Head Guard
• Cleansing Brush
• Power Adaptor
4
XR1415AU SPECIFICATIONS
Power System
Cordless
Full Charge Time
4 Hours
Cordless Run Time
45 Minutes
Indicators
LED Battery Indicators
Voltage Type
Worldwide 100 - 240V
Shaver Head Replacement Part No.
SPR-XR1415AU
Power System
The XR1415AU shaver can only be used without the power cord. The shaver will not
run while it is charging.
LED Battery Indicators
Lights display the battery charge level
•
Low Charge: Top LED light will glow solid red to indicate the shaver needs to
be recharged. There is less than 5 minutes of run time remaining.
•
Charging: Bottom LED light will glow solid green to indicate the battery is
taking a charge.
•
Full Charge: When fully charged the green LED light will go off.
Worldwide Voltage
Shaver automatically adapts to an outlet voltage between 100V and 240V.
NOTE: Some countries will require the use of a plug adaptor that is not included
with your shaver.
CHARGING
1.
Plug power cord adaptor into the shaver.
2.
Plug the adaptor into the wall outlet.
3.
Fully charge your shaver for 4 hours before its first use. This first charge is
important to the shaver’s battery life.
NOTE: During the initial charge ignore the electronic indicators as they are in “Start
Up Cycle”.
CAUTION:
•
Make sure the shaver and your hands are dry when charging the shaver.
•
Always charge the shaver in a cool, dry place.
5
CHANGING THE ATTACHMENTS
1.
The unit should be turned off when changing attachments.
2.
Remove the attachment by lifting upward from the base.
3.
After selecting the attachment you want, align the hexagon shapes of the
base and attachment and press to snap the attachment onto the base.
4.
For brush heads, first snap the brush mount onto the base. Then snap the
cleansing or pre-shave brush onto the brush mount.
INSTRUCTIONS FOR USE
Cleansing
1.
Add a drop of facial cleanser to the brush head and dampen under the faucet
or shower.
2.
Press on/off button to turn on.
3.
Divide your face into 4 main sections; forehead, nose and chin, left cheek,
right cheek.
4.
While applying gentle pressure, move the rotating brush in circular motions
over each section for approximately 30 seconds.
Grooming
1.
Use the grooming head without the adjustable
comb for trimming hair close to the skin.
2.
Attach the comb onto the groomer head by
hooking the front of the comb over the trimmer
blades, then snapping the comb down onto the
groomer.
Comb
Position
~Cut
Length
1
2mm
2
3mm
Adjust the comb setting to desired length by
rotating the wheel clockwise to increase length
and counterclockwise to reduce length.
3
4mm
4
5mm
4.
Press on/off button to turn the groomer on.
5
6mm
5.
Place the groomer head against the skin and
slide against the growth direction of hair.
3.
Pre-Shave
Use the silicone pre-shave massage brush to exfoliate skin and lift hair for an extra
close shave.
1.
Dampen the silicone pre-shave massage brush.
2.
Press on/off button to turn on.
3.
While applying gentle pressure, move the rotating brush in circular motions
over each section of face.
6
SHAVING
NOTE: If shaving with gel or foam, first wet face and then apply to applicable area.
1.
Press on/off button to turn the shaver on.
2.
Hold the shaver at a right angle to the skin so that all three heads are touching
the skin with equal pressure.
3.
Stretch the skin with free hand so hairs stand upright.
4.
While applying light pressure, use short, circular strokes to shave the face.
5.
Rinse shaver under warm water to clean away excess gel or debris.
SHAVING TIPS
•
Remington Quick Shave Pro Rotary Shaver is waterproof. You may use shaving
foam or gel with your shaver. You may also shave in the shower.
•
Wait at least 15 minutes after getting up before shaving, to ensure your face
is free of puffiness that may be present from sleeping.
•
Always hold the shaver at a right angle to the skin so that all three heads are
touching the skin with equal pressure.
•
Stretch skin with the free hand so hairs stand upright, making it easier for
them to enter the cutting chamber.
•
Use moderate to slow, circular stroking movement.
•
The use of short, circular motions in stubborn areas may obtain a closer
shave, especially along the neck and chin line.
•
Do not press hard against the skin as this can cause skin irritation and/or
damage to the rotary heads.
NOTE: When using the shaver with foam or gel it is important to rinse the cutting
head clean after each use. This will avoid having the foam or gel dry in the cutting
head and clogging the shaver.
TRIMMING
POP-UP TRIMMER:
1.
Pull down the pop up trimmer release button to engage trimmer (Diagram A).
2.
Trim and shape sideburns and facial hair to the desired length and shape.
3.
Close trimmer by pressing down (Diagram B).
NOTE: Lubricate teeth with
oil every 6 months.
B
A
7
$
$
$
$
$
$24.95 NZD
$24.95 NZD
$24.95 NZD
$14.95 NZD
$14.95 NZD
$19.95 AUD
$19.95 AUD
$19.95 AUD
$11.95 AUD
$11.95 AUD
SPR-XFMAU
SPR-XFNAU
SPR-XFDAU
SP4
SP5
Pre-Shave Brush
Charcoal Infused Deep Cleansing Brush
Daily Cleansing Brush
Shaver Saver: Aerosol Spray Cleaner
Face Saver: Pre-shave Powder Stick
Remington is a Registered Trademark
of Spectrum Brands, Inc., or one
of its subsidiaries.
Spectrum Brands Australia Pty Ltd
Locked Bag 3004
Braeside, VIC 3195
AUSTRALIA
$
$14.95 NZD
$9.95 AUD
SPR-XFOAU
Brush Mount for Brush Heads
TOTAL
$
$7.50
$
$
N/A
Sub Total
Postage &
handling
$
$44.95 NZD
$37.95 AUD
Replacement Shaving Heads & Cutters for XR1415AU
$39.95 AUD
Amount
SPR-XTAU
Qty
SPR-XR1415AU
Price each
NZD
Price each
AUD
Part No.
Beard Trimmer Attachment for XR1415AU
Article
SPARE PARTS ORDER FORM
CLEANING & MAINTENANCE
NOTE: When cleaning your shaver, make sure the shaver is turned off and
disconnected from the power cord.
The shaver is a washable appliance. The head and body may be cleaned under warm water.
CAUTION:
•
When cleaning the external surfaces of the shaver, do not use strong
detergents or other chemicals.
•
To dry, wipe the surface of the shaver with a dry towel. Do not use a hair dryer
or heater to dry the shaver.
NOTE: The shaver head and neck assembly is designed to be detachable from the
shaver body. Simply pull upwards from the neck of the shaver for easy release.
To reattach the neck, align it with the neck attachment cavity so that it clips back
into position.
CLEANING YOUR SHAVER
1
2
3
4
SHAVER PARTS
1.
2.
3.
4.
Head & cutter (hair pocket) assembly
Detachment grooves
Neck assembly
Neck attachment cavity
DAILY CLEANING
1.
Locate the detachment grooves on the head & cutter assembly. Gently pull to
detach the hair pocket from the neck assembly (Diagram C).
2.
Tap out excess hair shavings (Diagram D).
3.
Rinse the head of the shaver in running water.
4.
Gently reattach the hair pocket to the neck assembly until it locks in place
on all three sides. The hair pocket may be reattached in any configuration
(Diagram I).
10
LC
LC
LD
M
M
EM
N
G
PO
PP
QH
QIQ
NFN
O
WEEKLY CLEANING
1.
Perform the daily cleaning steps 1 and 2.
2.
Place the body of the shaver aside.
3.
Slide the blue cutter support frame upwards towards the direction of the two
cutters to release it from the assembly (Diagram E).
4.
Lift and remove the cutter support frame away from the cutters.
5.
Remove the cutters (Diagram F).
6.
Thoroughly rinse away any debris from inner and outer cutters with warm
water.
7.
Replace the inner cutters (Diagram G).
8.
Hold the cutter support frame with the raised centre section facing upwards.
Place it over the cutters so that the centre mouth opening is facing the
botttom cutter. Slide the cutter carrier downwards until the locking tab locks
under the centre triangle (Diagram H).
9.
Lubricate each cutter with Remington Shaver Saver (SP4).
10. Gently reattach the hair pocket to the neck assembly until it locks in place
on all three sides. The hair pocket may be reattached in any configuration
(Diagram I).
11
OO
REPLACING SHAVING HEADS & CUTTERS
Please refer to the shaver grid on page 5 of this manual that lists the correct
replacement part number for your shaver.
It is very important to replace the shaving heads and cutters when necessary
to ensure a close, comfortable shave without irritation. We recommend they be
replaced every 12 months. Here are some signs of head and cutter wear, indicating
that replacement is needed:
•
Irritation: As the heads get excessively worn you may experience some skin
irritation. This would be especially noticeable when you apply moisturising
lotion.
•
Pulling: When the cutters wear you may feel a sense of pulling and a loss of
closeness when you shave. This is an indication that it is time to replace the
shaving heads and cutters.
Replacement heads & cutters may be obtained from your local retailer, or directly
from Remington ®. Simply fill out the attached accessory order form or alternatively
your order can be processed over the phone via the Remington® Service Hotline refer to page 14.
This product is suitable for use in the bath or shower.
This product conforms to radio frequency interference requirements
Any product purchased and used commercially carries a limited 90 Day Warranty.
MONEY BACK OFFER – AUSTRALIA / NEW ZEALAND ONLY
If within 60 days you are not fully satisfied with your Remington ® shaver, just return the shaver
with this completed coupon and a copy of your Australian/New Zealand purchase receipt to
Remington ®. In return, we will send you a cheque for the full purchase price of the shaver.
Please allow 6-8 weeks for your cheque to arrive.
Name:
Address:
City:
State: Postcode:
Contact No: Area Code: Ph:
Product Model number:
Is this the first Remington shaver you have owned/purchased? Yes What is the reason you are returning this product?
12
No
Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Limited
WARRANTY AGAINST DEFECTS
In this warranty:
Australian Consumer Law means the Australian consumer law set out in Schedule 2 to the
Competition and Consumer Act 2010;
CGA means the New Zealand Consumer Guarantees Act 1993;
Goods means the product or equipment which was accompanied by this warranty and
purchased in Australia or New Zealand, as the case may be;
Manufacturer, We or us means:
1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd
ACN, 007 070 573; or
2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Limited,
as the case may be, contact details as set out at the end of this warranty;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods
in Australia or in New Zealand; and
You means you, the original end-user purchaser of the Goods.
1. Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law, or the CGA. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
2. The benefits provided by this Warranty are in addition to all other rights and remedies in
respect of the Goods which the consumer has under either the Australian Consumer Law
or the CGA. The original purchaser of the Goods is provided with the following Warranty
subject to the Warranty Conditions:
3. We warrant the Goods for all parts defective in workmanship or materials for the period of
two (2) years from the date of purchase (Warranty Period). If the Goods prove defective
within the Warranty Period by reason of improper workmanship or material, we may, at our
own discretion, repair or replace the Goods without charge.
Warranty Conditions
4. The Goods must be used in accordance with the manufacturer’s instructions. This Warranty
does not apply should the defect in or failure of the Goods be attributable to misuse, abuse,
accident or non-observance of manufacturer’s instructions on the part of the user. As far as
the law permits, the manufacturer does not accept liability for any direct or consequential
loss, damage or other expense caused by or arising out of any failure to use the Goods in
accordance with the manufacturer’s instructions.
5. Exhaustible components (such as shaver heads, cutters and foils) of the Goods are included
under this Warranty only where there is a defect in workmanship or materials used.
6. The warranty granted under clause 3 is limited to repair or replacement only.
7. Any parts of the Goods replaced during repairs or any product replaced remain the property
of the manufacturer. In the event of the Goods being replaced during the Warranty Period,
the warranty on the replacement Goods will expire on the same date as for the Warranty
Period on the original Goods which are replaced.
13
8. In order to claim under the warranty granted under clause 3 you must:
(a) Retain this warranty with your receipt/proof of purchase; and
(b) Return the Goods to us at the relevant address below or to the Supplier by prepaid
freight within the Warranty Period accompanied with (i) the legible and unmodified original
proof of purchase, which clearly indicates the name and address of the Supplier, the
date and place of purchase, the product name or other product serial number and (ii) this
warranty.
9. This warranty is immediately void if:
(a) Any serial number or appliance plate is removed or defaced;
(b) The Goods have been serviced or otherwise repaired by a person not authorised to do so
by us or where non approved replaced parts are used.
10. The Goods are designed for domestic use only. A limited 90-day Warranty applies to any
industrial or commercial use of the Goods. The Goods must be connected to the electrical
voltage requirements as specified in the ratings label located on the Goods.
11. This warranty does not cover the cost of claiming under the warranty or transport of the
Goods to and from the Supplier or us.
12. This warranty is only valid and enforceable in Australia against Spectrum Brands Australia
Pty Ltd and in New Zealand against Spectrum Brands New Zealand Limited.
Contact us or the Supplier for further details.
Spectrum Brands Australia Pty Ltd
Locked Bag 3004
Braeside, VIC 3195
AUSTRALIA
Customer service in Australia: 1800 623 118
E-mail: consumer.enquiry@remington-products.com.au
Website: www.remington-products.com.au
Spectrum Brands New Zealand Limited
PO Box 9817
Newmarket, Auckland 1149
NEW ZEALAND
Customer service in New Zealand: 0800 736 776
E-mail: info@remington.co.nz
www.remington.co.nz
REMINGTON SERVICE HOTLINE
Australia 1800 623 118 (toll free)
New Zealand 0800 736 776 (toll free)
Registered Trade Mark of Spectrum Brands, Inc., or one of its subsidiaries
Made in China to the Specifications of Spectrum Brands, Inc.
2017 Spectrum Brands Inc.
REV: 07/17
PART NO: T22-0005195
®
©
14
Download PDF
Similar pages