IECEx/ATEX INTRINSICALLY SAFE RADIO

VHF AND UHF DIGITAL TRANSCEIVERS (dPMR™)
(VHF transceiver for Europe version)
(UHF transceiver for Europe version)
(VHF transceiver for Export versions)
(UHF transceiver for Export versions)
IECEx/ATEX INTRINSICALLY SAFE RADIO
IP67
IEC Certifications
Mining : Ex ib I Mb
Gas
: Ex ib IIC T4 Gb
Dust
: Ex ib IIIC T110°C Db
–20°C≤Ta≤+55°C
IEC 60079-0 (2011), IEC 60079-11 (2011)
ATEX Certifications
Mining : I M2 Ex ib I Mb
Gas
: II 2G Ex ib IIC T4 Gb
Dust
: II 2D Ex ib IIIC T110°C Db
–20°C≤Ta≤+55°C
EN 60079-0 (2012), EN 60079-11 (2012)
IP67 Dust-tight & Waterproof Protection
The IC-F3202DEX/F3203DEX series provides rugged protection against dust and
water that is equivalent to IP67. The IC-F3202DEX/F3203DEX series can withstand 1m depth of water for 30 minutes and its dust-tight construction shuts out
powder dust, sand and other objects.
dPMR™ Mode 1/2 Operation
The IC-F3202DEX/F3203DEX series provides basic operation in dPMR Mode 1, 2
conventional mode. It is compatible with Mode 2 multi-site system. The following
dPMR features are programmable.
• PTT ID (TX)
• Individual/Group call
• Power ON/OFF status call (TX)
• Stun/kill/revive (RX)
• Ambience listening (RX)
• Emergency (TX)
• Lone worker/Man down function
• Digital voice scrambler
• Voting scan for Mode 2 multi-site system
TX: Transmit, RX: Receive
Analogue Mode Compatible
The IC-F3202DEX/F3203DEX series has built-in 5-Tone, 2-Tone, CTCSS and
DTCS signaling capability for analogue mode group communication and selective
calling. The lone worker and man down functions automatically send an emergency signal to assist in worker safety. The radio is perfect for use as an analogue
transceiver ready for future digital migration.
Other Features
• 16 memory channels with channel announcement function
• BIIS 1200 PTT ID transmission • DTMF autodial
• Three programmable buttons (including emergency red button)
• Low electrical resistivity body; Carrying case is not required
• 19.5–21 hours* operating time with BP-277EX (* 5: 5: 90 duty cycle with Power save.)
• Optional waterproof speaker-microphone, HM-203EX
VHF AND UHF TRANSCEIVERS (dPMR™)
SPECIFICATIONS
OPTIONS
IC-F3202DEX
IC-F3203DEX
IC-F4202DEX
IC-F4203DEX
BATTERY PACK
RAPID CHARGER
GENERAL
Frequency coverage
400–470, 450–520,
350–400 MHz
16 channels
16K0F3E, 14K0F3E, 8K50F3E, 4K00F1E/F1D
16K0F3E, 11K0F3E, 8K50F3E, 4K00F1E/F1D
7.4 V DC nominal
136–174 MHz
Number of channels
Type of
EUR
emission
EXP
Power supply requirement
Current drain (approx.)
Tx High
Rx Max. audio/Standby
Antenna impedance
Operating temperature range
Dimensions (W × H × D)
(Projections not included)
550 mA
300 mA (Internal SP)/110 mA (Digital mode)
50 Ω
–20°C to +55°C
BP-277EX
Rechargeable
Li-ion, 7.4 V
1800 mAh (min.)
1900 mAh (typ.)
Charges the BP-277EX in 2 hours (approx.).
SPEAKER-MICROPHONE
BELT CLIP
BC-123S*1
ANTENNAS
• FA-SC25V : 136–150 MHz
• FA-SC55V : 150–174 MHz
• FA-SC01U : 350–400 MHz
• FA-SC25U : 400–430 MHz
• FA-SC57U : 430–470 MHz
• FA-SC72U : 470–520 MHz
63 × 144 × 50 mm (With BP-277EX)
250 g (Radio only)
466 g (With MB-94EX, BP-277EX & FA-SC55V) 460 g (With MB-94EX, BP-277EX & FA-SC57U)
258 g (Radio only)
Weight (approx.)
TRANSMITTER
Output power (at 7.4 V DC)
Max. permissible deviation
Frequency stability
Spurious
EUR
emissions
EXP
FM Hum and Noise (EXP)
Residual modulations (EUR)
Audio harmonic distortion
FSK error
Ext. microphone connector
1 W, 0.8 W, 0.6 W (Hi, L2, L1)
±5.0 kHz/±4.0 kHz/±2.5 kHz (W/M/N)
±1.0 ppm
0.25 μW (≤ 1 GHz), 1.0 μW (> 1 GHz)
66 dB min.
46/40 dB typ. (W/N)
50/46 dB typ. (W/N)
54/53/50 dB typ. (W/M/N)
48/46/42 dB typ. (W/M/N)
1.0/1.0/1.5% typ. (W/M/N) (@ AF 1 kHz 40% deviation)
2.0% typ. (Digital)
1.5% typ. (Digital)
14-pin multi-connector/2.2 kΩ
*1 BC-123SA for USA.
SE for Europe. SV for Australia.
MB-94EX
Aligator type
Same as supplied.
HM-203EX
DO NOT use the transceiver with any other equipment other than the above options.
The battery charger, BC-212EX must not be used in an explosive atmosphere.
ATEX mining protection and meaning
I
M2 Ex
ib
I
Mb
Mb = Mining equipment protection level: High protection
I = Protection in mining group: Methane
RECEIVER
Digital (5% BER)
Sensitivity Analog (EUR, 20 dB SINAD)
Analog (EXP, 12 dB SINAD)
Adjacent channel selectivity
Spurious response
Intermodulation
BC-212EX
EUR
EXP
Hum and EUR (With CCITT filter)
EXP (Without CCITT filter)
noise
Audio output power
External speaker connector
–8 dBμV emf typ.
–9 dBμV emf typ.
–4 dBμV emf typ.
–5 dBμV emf typ.
0.24 μV typ.
0.22 μV typ.
78/75/70/62 dB typ. (W/M/N/D) 74/72/66/57 dB typ. (W/M/N/D)
85 dB typ. (W/M/N),
75 dB typ. (W/M/N),
87 dBμV emf typ. (Digital)
79 dBμV emf typ. (Digital)
67 dB typ. (W/M/N), 73 dBμV emf typ.(Digital)
75/75/67 dB typ. (W/N/D)
74/74/73 dB typ.(W/N/D)
53/51/48 dB typ. (W/M/N)
46/44/41 dB typ. (W/M/N)
48/43 dB typ. (W/N)
43/37 dB typ. (W/N)
400 mW typ. (at 5% distortion with 32 Ω load)
14-pin multi-connector/32 Ω
ib = Intrinsic safety
Ex = Explosion proof equipment
M2 = Must be switched OFF in case of firedamp
I = Group I, Mining
ATEX gas protection and meaning
II
2 G Ex ib IIC T4 Gb
T4 = Device surface temperature will not exceed 135°C
IIC = Protection in GAS group: Acetylene, Hydrogen
ib = Intrinsic safety
Measurements made in accordance with TIA-603, EN 300-086, EN 301-166.
All stated specifications are subject to change without notice or obligation.
Ex = Explosion proof equipment
G = Gas, vapour and mist
Applicable U.S. Military Specifications & IP Rating
2 = High level protection for use in Zone 1 (gas)
MIL 810G
Standard
Method
Low Pressure
500.5
High Temperature
501.5
Low Temperature
502.5
Temperature Shock
503.5
Solar Radiation
505.5
Rain Blowing/Drip
506.5
Humidity
507.5
Salt Fog
509.5
Dust Blowing
510.5
Immersion
512.5
Vibration
514.6
Shock
516.6
Also meets equivalent MIL-STD-810-C, -D, -E and -F.
Ingress Protection Standard
Dust & Water
Procedure
I, II
I, II
I, II
I-C
I
I, III
II
–
I
I
I
I, IV
II = Group II, other (non-mining) areas
ATEX dust protection and meaning
II 2 D Ex ib IIIC T110°C Db Db = Dust equipment protection level: High protection
T110°C = Maximum temperature of device surface
IIIC = Dust group: Conductive dust (R≤103Ωm)
ib = Intrinsic safety
Ex = Explosion proof equipment
D = Dust
2 = High level protection for use in Zone 21 (dust)
II = Group II, other (non-mining) areas
IP67 (Dust-tight and waterproof)
Supplied accessories: (May differ according to version)
• Battery pack, BP-277EX
• Belt clip, MB-94EX
• Battery charger, BC-212EX • AC adapter, BC-123S
Gb = GAS equipment protection level: High protection
* Please ask your dealer to ensure the ATEX and IECEx ratings are acceptable for
the intended place of use.
• Antenna
Read all instructions enclosed with the transceiver carefully and completely before using the transceiver.
Icom, Icom Inc. and Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand and/or other
countries. IDAS and IDAS logo are trademarks of Icom Incorporated. dPMR and the dPMR logo are trademarks of the dPMR MoU Association. All other trademarks are the properties of their respective holders.
1-1-32, Kamiminami, Hirano-Ku, Osaka 547-0003, Japan Phone: +81 (06) 6793 5302
Fax: +81 (06) 6793 0013
www.icom.co.jp/world
12421 Willows Road NE,
Kirkland, WA 98034, U.S.A.
Phone: +1 (425) 454-8155
Fax:
+1 (425) 454-1509
E-mail: sales@icomamerica.com
URL: http://www.icomamerica.com
Communication Equipment
Auf der Krautweide 24
65812 Bad Soden am Taunus, Germany
Phone: +49 (6196) 76685-0
Fax:
+49 (6196) 76685-50
E-mail: info@icomeurope.com
URL: http://www.icomeurope.com
Zac de la Plaine,
1 Rue Brindejonc des Moulinais, BP 45804,
31505 Toulouse Cedex 5, France
Phone: +33 (5) 61 36 03 03
Fax:
+33 (5) 61 36 03 00
E-mail: icom@icom-france.com
URL: http://www.icom-france.com
6F No. 68, Sec. 1 Cheng-Teh Road,
Taipei, Taiwan, R.O.C.
Phone: +886 (02) 2559 1899
Fax:
+886 (02) 2559 1874
E-mail: sales@asia-icom.com
URL: http://www.asia-icom.com
Glenwood Centre #150-6165
Highway 17A, Delta, B.C.,
V4K 5B8, Canada
Phone: +1 (604) 952-4266
Fax:
+1 (604) 952-0090
E-mail: info@icomcanada.com
URL: http://www.icomcanada.com
Ctra. Rubi, No. 88 "Edificio Can Castanyer"
Bajos A 08174, Sant Cugat del Valles,
Barcelona, Spain
Phone: +34 (93) 590 26 70
Fax:
+34 (93) 589 04 46
E-mail: icom@icomspain.com
URL: http://www.icomspain.com
Unit 1 / 103 Garden Road,
Clayton, VIC 3168 Australia
Phone: +61 (03) 9549 7500
Fax:
+61 (03) 9549 7505
E-mail: sales@icom.net.au
URL: http://www.icom.net.au
No.101, Building 9, Caifuxingyuan Park,
No.188 Maoting Road, Chedun Town,
Songjiang District, Shanghai, 201611, China
Phone: +86 (021) 6153 2768
Fax:
+86 (021) 5765 9987
E-mail: bjicom@bjicom.com
URL: http://www.bjicom.com
Rua Itororó, 444 Padre Eustáquio
Belo Horizonte MG,
CEP: 30720-450, Brazil
Phone: +55 (31) 3582 8847
Fax:
+55 (31) 3582 8987
E-mail: sales@icombrazil.com
Blacksole House, Altira Park,
Herne Bay, Kent, CT6 6GZ, U.K.
Phone: +44 (0) 1227 741741
Fax:
+44 (0) 1227 741742
E-mail: info@icomuk.co.uk
URL: http://www.icomuk.co.uk
39C Rennie Drive, Airport Oaks,
Auckland, New Zealand
Phone: +64 (09) 274 4062
Fax:
+64 (09) 274 4708
E-mail: inquiries@icom.co.nz
URL: http://www.icom.co.nz
Count on us!
Your local distributor/dealer:
15HS020B
© 2015–2016 Icom Inc.
Printed in Japan
Download PDF
Similar pages