Untitled - Harbor Freight Tools

Table of contents
SAfETy
Safety .................................................2
Specifications .....................................8
Setup ..................................................9
Operation ...........................................10
Maintenance ......................................12
Parts List and Diagram ......................14
Warranty ............................................16
WARNING SyMBOLS AND DEfINITIONS
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.
SETUP
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
OPERATION
IMPORTANT SAfETy INfORMATION
General Power Tool Safety Warnings
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term ″power tool″ in the warnings refers to your mains-operated (corded) power tool.
MAINTENANcE
Work Area Safety
1. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools create sparks which
may ignite the dust or fumes.
Page 2
3. Keep children and bystanders
away while operating a power tool.
Distractions can cause you to lose control.
For technical questions, please call 1-888-866-5797.
Item 61741
2. Avoid body contact with grounded
5. When operating a power tool outdoors,
use an extension cord
surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased
suitable for outdoor use.
Use of a cord suitable for outdoor use
risk of electric shock if your body is grounded.
reduces the risk of electric shock.
3. Do not expose power tools to rain or
wet conditions. Water entering a power
6. If operating a power tool in a damp
tool will increase the risk of electric shock.
location is unavoidable, use a Ground
fault circuit Interrupter (GfcI)
protected supply. Use of a GFCI
reduces the risk of electric shock.
Personal Safety
2. Use personal protective equipment.
Always wear eye protection.
Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or
hearing protection used for appropriate
conditions will reduce personal injuries.
3. Prevent unintentional starting.
Ensure the Trigger is in the off‑position
before connecting to power source,
picking up or carrying the tool.
Carrying power tools with your finger on
the Trigger or energizing power tools that
have the Trigger on invites accidents.
4. Remove any adjusting key or wrench
before turning the power tool on.
A wrench or a key left attached to
a rotating part of the power tool
may result in personal injury.
Item 61741
5. Do not overreach. Keep proper
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
6. Dress properly. Do not wear loose
clothing or jewelry. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewelry or long
hair can be caught in moving parts.
7. If devices are provided for the connection
of dust extraction and collection
facilities, ensure these are connected
and properly used. Use of dust collection
can reduce dust-related hazards.
8. Only use safety equipment
that has been approved by an
appropriate standards agency.
Unapproved safety equipment may
not provide adequate protection.
Eye protection must be ANSI-approved
and breathing protection must be
NIOSH-approved for the specific
hazards in the work area.
For technical questions, please call 1-888-866-5797.
MAINTENANcE
1. Stay alert, watch what you are
doing and use common sense when
operating a power tool. Do not use
a power tool while you are tired or
under the influence of drugs, alcohol
or medication. A moment of inattention
while operating power tools may
result in serious personal injury.
SETUP
4. Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase
the risk of electric shock.
OPERATION
1. Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs
with grounded power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
SAfETy
Electrical Safety
Page 3
Power Tool Use and care
SAfETy
1. Do not force the power tool. Use
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
2. Do not use the power tool if the Trigger
does not turn it on and off.
Any power tool that cannot be
controlled with the Trigger is
dangerous and must be repaired.
SETUP
3. Disconnect the plug from the power
source before making any adjustments,
changing accessories, or storing
power tools. Such preventive safety
measures reduce the risk of starting
the power tool accidentally.
4. Store idle power tools out of the
reach of children and do not allow
persons unfamiliar with the power tool
or these instructions to operate the
power tool. Power tools are dangerous
in the hands of untrained users.
5. Maintain power tools. check for
misalignment or binding of moving
parts, breakage of parts and any other
condition that may affect the power tool’s
operation. If damaged, have the power
tool repaired before use. Many accidents
are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely
to bind and are easier to control.
7. Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
Service
OPERATION
Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Drill Safety Warnings
1. Use auxiliary handle(s), if supplied
with the tool. Loss of control
can cause personal injury.
5. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
MAINTENANcE
2. Hold power tools by insulated gripping
surfaces, when performing an operation
6. Avoid unintentional starting.
Prepare to begin work before
where the cutting accessory may contact
turning on the tool.
hidden wiring or its own cord. Cutting
accessory contacting a ″live″ wire may make
7. Do not lay the tool down until it has come to
exposed metal parts of the power tool ″live″
a complete stop. Moving parts can grab the
and could give the operator an electric shock.
surface and pull the tool out of your control.
3. Let bit cool before touching, changing
8. When using a handheld power tool,
or adjusting it. Bits heat up dramatically
maintain a firm grip on the tool with
while in use, and can burn you.
both hands to resist starting torque.
4. If the drill bit jams, release the
9. Do not leave the tool unattended when
Trigger immediately; drill torque
it is plugged into an electrical outlet.
can cause injury or break bit.
Turn off the tool, and unplug it from
its electrical outlet before leaving.
Page 4
For technical questions, please call 1-888-866-5797.
Item 61741
12. WARNING: Some dust created by power
sanding, sawing, grinding, drilling, and
other construction activities, contains
chemicals known [to the State of California]
to cause cancer, birth defects or other
reproductive harm. Some examples of
these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement or
other masonry products
13. WARNING: Handling the cord on this product
will expose you to lead, a chemical known
to the State of California to cause cancer,
and birth defects or other reproductive harm.
Wash hands after handling.
(California Health & Safety Code
§ 25249.5, et seq.)
14. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
SAfETy
11. People with pacemakers should consult their
physician(s) before use. Electromagnetic
fields in close proximity to heart pacemaker
could cause pacemaker interference or
pacemaker failure. In addition, people with
pacemakers should:
• Avoid operating alone.
• Do not use with Trigger locked on.
• Properly maintain and inspect to avoid
electrical shock.
• Properly ground power cord.
Ground Fault Circuit Interrupter (GFCI)
should also be implemented – it prevents
sustained electrical shock.
• Arsenic and chromium from
chemically treated lumber
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to these
chemicals: work in a well ventilated area,
and work with approved safety equipment,
such as those dust masks that are specially
designed to filter out microscopic particles.
(California Health & Safety Code
§ 25249.5, et seq.)
SETUP
10. This product is not a toy.
Keep it out of reach of children.
1. Anyone using vibrating tools regularly
or for an extended period should first
be examined by a doctor and then have
regular medical check-ups to ensure
medical problems are not being caused
or worsened from use. Pregnant women
or people who have impaired blood
circulation to the hand, past hand injuries,
nervous system disorders, diabetes, or
Raynaud’s Disease should not use this tool.
If you feel any symptoms related to
vibration (such as tingling, numbness,
and white or blue fingers), seek medical
advice as soon as possible.
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
4. Use tools with the lowest vibration
when there is a choice.
5. Include vibration-free periods
each day of work.
6. Grip tool as lightly as possible
(while still keeping safe control of it).
Let the tool do the work.
7. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.
SAVE THESE INSTRUcTIONS.
Item 61741
For technical questions, please call 1-888-866-5797.
Page 5
MAINTENANcE
This tool vibrates during use.
Repeated or long-term exposure to vibration may
cause temporary or permanent physical injury,
particularly to the hands, arms and shoulders.
To reduce the risk of vibration-related injury:
OPERATION
Vibration Safety
Grounding
SAfETy
TO PREVENT ELEcTRIc SHOcK AND DEATH fROM INcORREcT GROUNDING
WIRE cONNEcTION:
check with a qualified electrician if you are in doubt as to whether the outlet is
properly grounded. Do not modify the power cord plug provided with the tool.
Never remove the grounding prong from the plug. Do not use the tool if the power cord or
plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will
not fit the outlet, have a proper outlet installed by a qualified electrician.
Grounded Tools: Tools with Three Prong Plugs
SETUP
2. The grounding prong in the plug is
connected through the green wire inside
the cord to the grounding system in the tool.
The green wire in the cord must be
the only wire connected to the tool’s
grounding system and must never be
attached to an electrically “live” terminal.
3. The tool must be plugged into an appropriate
outlet, properly installed and grounded in
1. Tools marked with “Grounding Required”
accordance with all codes and ordinances.
have a three wire cord and three prong
The plug and outlet should look like those in
grounding plug. The plug must be connected
the preceding illustration.
to a properly grounded outlet. If the tool
(See 3‑Prong Plug and Outlet.)
should electrically malfunction or break
down, grounding provides a low resistance
path to carry electricity away from the
user, reducing the risk of electric shock.
3‑Prong Plug and Outlet
OPERATION
Double Insulated Tools: Tools with Two Prong Plugs
1. Tools marked “Double Insulated” do not
require grounding. They have a special
double insulation system which satisfies
OSHA requirements and complies with
the applicable standards of Underwriters
Laboratories, Inc., the Canadian Standard
Association, and the National Electrical Code.
MAINTENANcE
Outlets for 2‑Prong Plug
Page 6
2. Double insulated tools may be used in either
of the 120 volt outlets shown in the preceding
illustration. (See Outlets for 2‑Prong Plug.)
For technical questions, please call 1-888-866-5797.
Item 61741
Extension cords
SAfETy
Symbology
Double Insulated
Canadian Standards Association
n0 xxxx/min.
No Load Revolutions
per Minute (RPM)
WARNING marking concerning
Risk of Eye Injury.
Wear ANSI-approved safety
goggles with side shields.
Underwriters Laboratories, Inc.
Read the manual before
set-up and/or use.
V
Volts
~
Alternating Current
A
Amperes
WARNING marking concerning
Risk of Fire.
Do not cover ventilation ducts.
Keep flammable objects away.
WARNING marking concerning
Risk of Electric Shock.
Properly connect power
cord to appropriate outlet.
Item 61741
SETUP
150´
0 – 2.0
18 18 18 18 16
2.1 – 3.4
18 18 18 16 14
3.5 – 5.0
18 18 16 14 12
5.1 – 7.0
18 16 14 12 12
7.1 – 12.0
18 14 12 10
12.1 – 16.0
14 12 10
16.1 – 20.0
12 10
* Based on limiting the line voltage drop to
five volts at 150% of the rated amperes.
OPERATION
6. If you are using an extension cord
outdoors, make sure it is marked with the
suffix “W-A” (“W” in Canada) to indicate
it is acceptable for outdoor use.
(at full load)
EXTENSION cORD
LENGTH
For technical questions, please call 1-888-866-5797.
Page 7
MAINTENANcE
5. If you are using one extension cord for more
than one tool, add the nameplate amperes
and use the sum to determine the required
minimum cord size. (See Table A.)
NAMEPLATE
AMPERES
100´
4. When using more than one extension cord
to make up the total length, make sure
each cord contains at least the minimum
wire size required. (See Table A.)
Table A: Recommended Minimum
Wire Gauge for Extension cords*
(120/240 Volt)
75´
3. The smaller the gauge number of the wire,
the greater the capacity of the cord. For
example, a 14 gauge cord can carry a higher
current than a 16 gauge cord. (See Table A.)
8. Protect the extension cords from
sharp objects, excessive heat,
and damp or wet areas.
50´
2. As the distance from the supply outlet
increases, you must use a heavier gauge
extension cord. Using extension cords with
inadequately sized wire causes a serious
drop in voltage, resulting in loss of power
and possible tool damage. (See Table A.)
7. Make sure the extension cord is properly
wired and in good electrical condition.
Always replace a damaged extension
cord or have it repaired by a qualified
electrician before using it.
25´
1. Grounded tools require a
three wire extension cord.
Double Insulated tools can use either
a two or three wire extension cord.
Specifications
SAfETy
Electrical Rating
120VAC / 60Hz / 6.3A
Motor No Load Speed
0-1200 RPM
Chuck Capacity
1/16" - 1/2" (12.7mm)
Max. Bit Diameter
1/2"
4006159
SETUP
OPERATION
MAINTENANcE
Page 8
For technical questions, please call 1-888-866-5797.
Item 61741
Setup ‑ Before Use:
SAfETy
Read the ENTIRE IMPORTANT SAfETy INfORMATION section
at the beginning of this manual including all text under
subheadings therein before set up or use of this product.
Functions
Power Indicator Light
SETUP
Side Handle
chuck
Direction
Button
OPERATION
Trigger
Lock ON
Button
MAINTENANcE
chuck
Key
Item 61741
For technical questions, please call 1-888-866-5797.
Page 9
Operating Instructions
SAfETy
Read the ENTIRE IMPORTANT SAfETy INfORMATION section
at the beginning of this manual including all text under
subheadings therein before set up or use of this product.
Tool Set Up
TO PREVENT SERIOUS INJURy fROM AccIDENTAL OPERATION:
Make sure that the Trigger is in the off‑position and unplug the tool from
its electrical outlet before adjusting tool or installing accessories.
Thread the Side Handle fully into a
hole in the side of the housing.
SETUP
Drill Bit Installation
cAUTION! Wear heavy-duty work gloves
to provide protection when inserting
and removing drill bits. Drill bits become
very hot during use. Do not remove
drill bits until the bit has cooled.
1. Loosen the Chuck with the Chuck Key
until the jaws of the drill are opened
enough to fit the drill bit.
OPERATION
2. Place the desired drill bit or screwdriver bit
into the drill between the Chuck Jaws.
NOTIcE: Use sharp bits. Dull, bent,
or damaged bits will cause stress
on the drill and/or break.
3. Insert the tip of the Chuck Key into a hole
on the side of the Chuck so that the teeth
on the Key engage the gear on the Chuck.
4. Keep the bit centered in the Chuck jaws
while tightening the Chuck securely
with the Key. Then, remove the Key.
Workpiece and Work Area Set Up
1. Designate a work area that is clean
and well lit. The work area must not
allow access by children or pets to
prevent distraction and injury.
MAINTENANcE
2. Route the power cord along a safe route
to reach the work area without creating a
tripping hazard or exposing the power cord
to possible damage. The power cord must
reach the work area with enough extra length
to allow free movement while working.
Page 10
3. Secure loose workpieces using a
vise or clamps (not included) to
prevent movement while working.
4. There must not be objects, such
as utility lines, nearby that will
present a hazard while working.
For technical questions, please call 1-888-866-5797.
Item 61741
cAUTION! The bit may be hot to the touch.
Allow the bit to cool before removing.
2. Slide the Direction Button to
the forward setting.
Note: If a bit becomes wedged into workpiece,
stop and slide the Direction Button to the
reverse setting. Then slowly squeeze the
Trigger to back the bit out of the workpiece.
3. Place the tip of the drill bit on the workpiece.
4. Grasp the handles firmly with both hands
and slowly squeeze the Trigger.
5. To lock the Drill on, press and hold the
Trigger then press the Lock ON Button.
Release the Trigger then the Lock
ON Button. Press and release the
Trigger to turn the Drill off.
6. Allow the bit to cut the hole.
8. To prevent accidents, turn off the tool and
unplug it after use. Clean, then store the
tool indoors out of children’s reach.
MAINTENANcE
OPERATION
7. Remove the bit from the finished hole then
release the Trigger, or press and release the
Trigger if the Lock ON Button is engaged.
Wait for the Drill to come to a complete
stop before laying the tool down.
Note: When drilling wood, plastic or
plastic-coated chip board, place bit at point to
be drilled. When drilling metal, use a punch
(sold separately) to mark the drilling position.
Use a lubricant to the prolong life of bit and
increase drilling action with most metals.
With steel, tin, and sheet metal use a light
machine oil, with aluminum, use paraffin. Do not
use lubricants with brass, copper, and cast iron.
SETUP
1. Make sure that the Trigger is in the
off-position, then plug in the tool.
SAfETy
General Operating Instructions
Item 61741
For technical questions, please call 1-888-866-5797.
Page 11
Maintenance and Servicing
SAfETy
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURy fROM AccIDENTAL OPERATION:
Make sure that the Trigger is in the off‑position and unplug the tool from its electrical
outlet before performing any inspection, maintenance, or cleaning procedures.
TO PREVENT SERIOUS INJURy fROM TOOL fAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.
cleaning, Maintenance, and Lubrication
SETUP
1. BEfORE EAcH USE, inspect the general
condition of the tool. Check for:
• loose hardware,
• misalignment or binding of moving parts,
• cracked or broken parts,
• damaged electrical wiring, and
2. AfTER USE, wipe external surfaces
of the tool with clean cloth.
3.
WARNING! If the supply cord
of this power tool is damaged,
it must be replaced only by a
qualified service technician.
• any other condition that may
affect its safe operation.
OPERATION
MAINTENANcE
Page 12
For technical questions, please call 1-888-866-5797.
Item 61741
Troubleshooting
Performance
decreases
over time.
Excessive noise
or rattling.
Overheating.
2. No power at outlet.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other loads.
3. Tool’s thermal reset
breaker tripped
(if equipped).
3. Turn off tool and allow to cool.
Press reset button on tool.
4. Internal damage
or wear.
(Carbon brushes or
switch, for example.)
Extension cord too long
or wire size too small.
4. Have technician service tool.
1. Accessory dull
or damaged.
2. Carbon brushes
worn or damaged.
Internal damage or wear.
(Carbon brushes or
bearings, for example.)
1. Forcing tool to
work too fast.
Eliminate use of extension cord.
If an extension cord is needed, use shorter/
heavier gauge cord. See Extension Cords
in Grounding section on page 6.
1. Keep cutting accessories sharp.
Replace as needed.
SETUP
Tool operates
slowly.
Likely Solutions
1. Check that cord is plugged in.
2. Have qualified technician replace brushes.
Have technician service tool.
1. Allow tool to work at its own rate.
2. Accessory misaligned. 2. Check and correct accessory to
fence and/or table alignment.
3. Accessory dull
or damaged.
3. Keep cutting accessories sharp.
Replace as needed.
4. Blocked motor
housing vents.
4. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while
blowing dust out of motor using compressed air.
5. Motor being
strained by long
or small diameter
extension cord.
5. Eliminate use of extension cord.
If an extension cord is needed, use one
with the proper diameter for its length
and load. See Extension Cords in
Grounding section on page 6.
For technical questions, please call 1-888-866-5797.
MAINTENANcE
follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.
Item 61741
SAfETy
Possible causes
OPERATION
Problem
Tool will not start. 1. Cord not connected.
Page 13
PLEASE READ THE fOLLOWING cAREfULLy
SAfETy
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND
ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY
OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS
TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS
TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Parts List and Diagram
SETUP
Parts List
Part
OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Description
Screw M5X20
Chuck
Chuck Key
Spindle
Spindle Key
Flange Clip
Screw st 4.2X 30
Side Handle
Bearing 6002
Head Shell
Bearing 606ZZ
Middle Spindle Gear
Middle Spindle Clip
Large Gear
Steel Ball
Small Gear
Large Gear Clip
Needle Bearing hk0810
Oil Seal 6X8X10
Gearbox Middle Cover
Qty
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
Part
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Description
Brush Holder Cap
Carbon Brush
Brush Holder
Right Housing
Screw st 4.2X16
LED
Switch
Cable Plate
Screw st 4.2X14
Power Cord
Cord Protector
Left Housing
Direction Button
Stator
Screw st 4.2X60
Baffle Ring
Bearing
Rotor
Fan
Bearing 609ZZ
Qty
2
2
2
1
6
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
MAINTENANcE
Page 14
For technical questions, please call 1-888-866-5797.
Item 61741
MAINTENANcE
OPERATION
SETUP
SAfETy
Assembly Diagram
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Item 61741
For technical questions, please call 1-888-866-5797.
Page 15
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase. This
warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or
accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to
you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection verifies the defect, we will either repair or
replace the product at our election or we may elect to refund the purchase price if we cannot
readily and quickly provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted from causes not
within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • camarillo, cA 93011 • 1‑888‑866‑5797
Download PDF
Similar pages